Nick Hainke [Fri, 13 Jan 2023 23:20:32 +0000 (00:20 +0100)]
archs38: switch to 5.15 by default
It appears that only a few users are using the archs38 SoC. The most
active user of the target has already approved the testing kernel and
so it is very unlikely bugs will be reported in the near future.
Therefore, the target should be directly bumped to 5.15.
David Bauer [Mon, 16 Jan 2023 00:30:29 +0000 (01:30 +0100)]
dosfstools: switch to AC_CHECK_LIB
This fixes spurious build-errors on OpenWrt, where the AM_ICONV macro
is undefined while invoking autoconfig. Later in the build, the ICONV
LDOPTIONS are set to @LIBICONV@, failing the build.
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard (J1004)
the connector size is a 4-pin 2.0 mm JST PH.
RX/TX is working, u-boot bootwait is active, secure boot is enabled.
Notes:
- Serial is completely deactivated in the stock firmware image.
- This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
- Installation can be done by serial connection or
SSH access on OEM firmware
Installation Instructions:
Most part of the installation is performed from an initramfs image
running OpenWrt, and there are two options to boot it.
Boot initramfs option 1: Using serial connection (3.3V)
1. Stop auto boot to get to U-boot shell
2. Transfer initramfs image to device
(openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
Tested using TFTP and a FAT-formatted USB flash drive.
3. Boot the initramfs image
# bootm
Boot initramfs option 2: From SSH access on OEM firmware
1. Copy the initramfs image to a FAT-formatted flash drive
(tested on single-partition drive) and connect it to device USB port.
2. Change boot command so it loads the initramfs image on next boot
Fallback to OEM firmware is provided.
# fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
3. Reboot the device to boot the initramfs
# reboot
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Check MTD partition table.
rootfs and rootfs_1 should be mtd18 and mtd20
depending on current OEM slot.
# cat /proc/mtd
4. Do a ubiformat to both rootfs partitions:
# ubiformat /dev/mtd18 -y -f /path_to/factory_image
# ubiformat /dev/mtd20 -y -f /path_to/factory_image
5. Set U-boot env variable: mtdids
# fw_setenv mtdids 'nand0=nand0'
6. Get offset of mtd18 to determine current OEM slot
- If current OEM slot is 1, offset is 16777216 (0x1000000)
- If current OEM slot is 2, offset is 127926272 (0x7a00000)
# cat /sys/class/mtd/mtd18/offset
7. Set U-boot env variable: mtdparts
If current OEM slot is 1, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)'
If current OEM slot is 2, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)'
8. Set U-boot env variable: bootcmd
# fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0'
9. Reboot the device
# reboot
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Robert Marko [Mon, 10 Jan 2022 23:50:37 +0000 (00:50 +0100)]
ipq807x: Add Xiaomi AX9000
Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet:
* 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* 1x2.5G RJ45 port (QCA8081) with 1x status LED
* WLAN:
* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
* 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
* 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate
* 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate
* USB: 1x USB3.0 Type-A port
* LED-s:
* System (Blue and Yellow)
* Network (Blue and Yellow)
* RGB light bar on top in X shape
* Buttons:
* 1x Power switch
* 1x Soft reset
* 1x Mesh button
* Power: 12V DC Jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd21 and mtd22 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
• LEDs:
7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, hold WPS button til the second beep
(yes the router has a buzzer)
SSH is available on port 22200, login with user admin and
password "mac address of the router".
Installation Instructions:
• obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial)
• stop auto boot
• setenv serverip 192.168.10.1
• setenv ipaddr 192.168.10.10
• tftpboot the initramfs image
(openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb)
• bootm
• make sure that current_entry is set to "0":
"fw_printenv -n current_entry" should be print "0". If not,
do "fw_setenv current_entry 0"
• copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
to the device to /tmp folder
• sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4)
• reboot
Note: this leaves the second kernel / rootfs parition untouched. So if you want
to go back to stock, stop u-boot autoboot, "setenv current_entry 1" ,
"saveenv", "bootipq".
Stock firmware should start from the second partition.
Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt
in the first partitions
Make 10G Aquantia phy's work:
The aquantia phy's need a firmware to work. This can either be loaded
in linux with a userspace tool or in u-boot.
I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is
aq_load_fw available in u-boot. But first the right firmware needs to write
to the 0:ETHPHYFW mtd partition (it is empty on my device)
Grab the ethphy firmware image from:
https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn
and scp that to openwrt.
Check the 0:ETHPHYFW partition number:
cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10.
Backup the 0:ETHPHYFW partition:
dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place.
Write the new firmware image to the 0:ETHPHYFW partition:
"mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10".
Reboot to u-boot.
Check if aq_load_fw is working:
"aq_load_fw 0", that checks the firmware and if successfull,
loads iram and dram to one of the aquantia phy's.
If that worked, add the aq_load_fw to the bootcmd:
setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq"
"saveenv"
"reset"
Board reboots and the firmware load to both phy's should start and
then openwrt boots.
Check if the 10G ports work.
Note: lan port labeled "10G-2" is configured as WAN port as per default.
All other port are in the br-lan. This can be changed in the network config.
• LEDs:
3 x GPIO-controlled System-LEDs
(form one virtual RGB System-LED)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An unpopulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, but it drops only
to a limited shell .
Installation Instructions:
black_small_square obtain serial access
black_small_square stop auto boot
black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
black_small_square bootm
black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
to the device
black_small_square write the image to the NAND:
black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs-
nand-factory.ubi
black_small_square reboot
Note: Device is not using dual partitioning (NAND contains other partitions
with different manufacture data etc.)
Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Robert Marko [Wed, 19 May 2021 19:04:43 +0000 (21:04 +0200)]
ipq807x: add Xiaomi AX3600
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* WLAN:
* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
* System (Blue and Yellow)
* IoT (Blue)
* Network (Blue and Yellow)
* Buttons: 1x Soft reset
* Power: 12V DC Jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm NSS-DP is as its name says Qualcomms ethernet driver for the NSS
subsystem (Networking subsystem) built-into various Qualcomm SoCs.
It has 2 modes of operation:
* Without NSS FW and rest of code required for offloading
This is the one that we will use as the amount of kernel patching required
for NSS offloading and the fact that its not upstreamable at all makes it
unusable for us.
Driver in this mode is rather basic, it currently only offers NAPI GRO
(Added by us as part of the fixup) and basically relies on the powerfull
CPU to get good throughput.
* With NSS FW and rest of code required for offloading
In this mode, driver just registers the interfaces and hooks them into
NSS-ECM to allow offloading.
This mode is not viable for use in OpenWrt due to reasons already described
above.
This driver is required for ipq807x to have wired networking until a better
one is available, so lets add the fixed-up version for 5.15 for now.
Robert Marko [Tue, 13 Dec 2022 22:55:26 +0000 (23:55 +0100)]
mac80211: add ath11k AHB support
This is the follow up to the PCI support commit now providing support for
AHB variant as well, though currently only for ipq807x as that is only
OpenWrt supported SoC ath11k supports as well.
Currently, we are disabling coldboot calibration on ipq807x as it does not
work, there is a remoteproc bug that makes it come late out of reset so
disable coldboot until that is fixed.
Also, as ath11k is quite memory hungry, we are introducing a config option
to use the limits for 512MB of RAM, similar to what QCA does downstream but
in way simpler and cleaner way so that 512MB save some RAM.
512MB profile is also set as the default for now.
Robert Marko [Sat, 5 Feb 2022 22:40:51 +0000 (23:40 +0100)]
ipq807x: add Qualcomm Atheros IPQ807x target
Qualcomm Atheros IPQ807x is a modern WiSoC featuring:
* Quad Core ARMv8 Cortex A-53
* @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye
* @ 1.4 GHz (IPQ8070A/1A) Codename Acorn
* Dual Band simultaneaous IEEE 802.11ax
* 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A)
* 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A)
* 5G: 2x2/80MHz (IPQ8070A)
* 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A)
* 2G: 2x2/40MHz (IPQ8070A/1A)
* 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports)
* 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye
* 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn
* DDR3L/4 32/16 bit up to 2400MT/s
* SDIO 3.0/SD card 3.0/eMMC 5.1
* Dual USB 3.0
* One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane)
* Parallel NAND (ONFI)/LCD
* 6x QUP BLSP SPI/I2C/UART
* I2S, PCM, and TDMA
* HW PWM
* 1.8V configurable GPIO
* Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc)
Note that only v2 SOC models aka the ones ending with A suffix are
supported, v1 models do not comply to the final 802.11ax and have
lower clocks, lack the Gen3 PCIe etc.
SoC itself has two UBI32 cores for the NSS offloading system, however
currently no offloading is supported.
Robert Marko [Tue, 13 Dec 2022 22:26:37 +0000 (23:26 +0100)]
generic: 5.15: add MHI SBL callback for ath11k
This adds the MHI SBL callback that ath11k will utilize in order to
support multiple PCI cards or AHB+PCI combo which currently does not
work due to QRTR ID-s conflicting.
This is a prerequisite for the mac80211 patch targeting ath11k as it
uses MHI from kernel.
Robert Marko [Thu, 29 Dec 2022 18:23:11 +0000 (19:23 +0100)]
archs38: mark as source-only
archs38 seems to be pretty much unused, usually only treewide changes or
kernel bumps in order to branch off new stable are done to it.
Considering that target only support some Synopsis HS38 ARC reference
boards and no consumer hardware so mark the target as source-only to stop
using Buildbot resources on building the target and packages for it.
Harm Berntsen [Sun, 8 Jan 2023 16:03:25 +0000 (17:03 +0100)]
ramips: mt7621: Add Arcadyan WE420223-99 support
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access
point distributed as Experia WiFi by KPN in the Netherlands. It features
two ethernet ports and 2 internal antennas.
Specifications
--------------
SOC : Mediatek MT7621AT
ETH : Two 1 gigabit ports, built into the SOC
WIFI : MT7615DN
BUTTON: Reset
BUTTON: WPS
LED : Power (green+red)
LED : WiFi (green+blue)
LED : WPS (green+red)
LED : Followme (green+red)
Power : 12 VDC, 1A barrel plug
Serial
------
The serial port needs a TTL/RS-232 3V3 level converter! The Serial
setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin
header.
The pinout is: VCC (the square), RX, TX, GND.
Installation
------------
See the Wiki page [1] for more details, it comes down to:
1. Open the device, take off the heat sink
2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also
connect the RESET pin for stability (thanks @FPSUsername for reporting)
3. Make a backup in case you want to revert to stock later
4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash
5. Ensure the bootpartition variable is set to 0 in the U-Boot
environment located at 0x30000
Note that the U-Boot is password protected, this can optionally be
removed. See the forum [2] for more details.
The label address is stored in ASCII in the board_data partition
Notes
-----
- This device has a dual-boot partition scheme, but OpenWRT will claim
both partitions for more storage space.
Known issues
------------
- 2g MAC address does not match stock due to missing support for that in
macaddr_add
- Only the power LED is configured by default
- The three WiFis were fully tested and are configured with the same settings as in the vendor firmware.
- The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream.
- Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working.
Bluetooth:
========
- Fully working with the following caveats:
- RFKILL need to be enabled in the kernel.
- An older version of bluez is needed as bccmd is needed to configure the chip.
Zigbee:
======
- The spidev device is available in the /dev directory.
- GPIOs are configured the same way as in the vendor firmware.
- Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working.
Installation:
=========
The squash-factory image can be installed via the Linksys Web UI:
1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device).
2. Login with your admin password.
3. To enter into the support mode, click on the "CA" link and the bottom of the page.
4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button.
5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups.
The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts.
If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row.
It can also be done via TFTP:
1. Setup a local TFTP server and configure its IP to 192.168.1.100.
2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server.
3. Connect to the device through the serial console.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2".
6. Once flashed, enter "reset" to reboot the device.
Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
Marcin Gajda [Wed, 28 Dec 2022 18:01:40 +0000 (19:01 +0100)]
ipq40xx: Add support ZTE MF18A
Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home).
Device specification
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz (QCA9982): a/n/ac, 3x3
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up)
Power: 5VDC, 2,1A via USB-C socket
Bootloader: U-Boot
On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software )
Installation
1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port,
with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) :
VCC (3.3V). Do not use unless you need to source power for the converer from it.
TX
RX
GND
Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1.
2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
3.Connect TFTP server to RJ-45 port (WAN/LAN1).
4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb
bootm 0x84000000
5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do:
If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command:
nand erase 0x1800000 0x1D00000
6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1):
ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it
7. Install image via :
sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin
previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward.
Back to Stock (!!! need original dump taken from initramfs !!!) -------------
Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
Connect serial console (115200,8n1) to serial console connector .
Connect TFTP server to RJ-45 port (WAN/LAN1).
rename mtd8.bin to web.img and mtd9.bin to root_uImage_s
Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase Web and RootFS:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 root_uImage_s
nand erase 0x1800000 0x1D00000
nand write 0x84000000 0x1800000 0x1D00000
This will restore Web Interface:
tftpboot 0x84000000 web.img
nand erase 0x1000000 0x800000
nand write 0x84000000 0x1000000 0x800000
After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router
As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com
Luo Chongjun [Thu, 15 Dec 2022 09:25:15 +0000 (17:25 +0800)]
ath79: Fix glinet ar300m usb not working
glinet forum users reported the problem at
https://forum.gl-inet.com/t/gl-ar300m16-openwrt-22-03-0-rc5-usb-port-power-off-by-default/23199
The current code uses the regulator framework to control the USB power
supply. Although usb0 described in DTS refers to the regulator by
vbus-supply, but there is no code related to regulator implemented
in the USB driver of QCA953X, so the USB of the device cannot work.
Under the regulator framework, adding the regulator-always-on attribute
fixes this problem, but it means that USB power will not be able to be
turned off. Since we need to control the USB power supply in user space,
I didn't find any other better way under the regulator framework of Linux,
so I directly export gpio.
Signed-off-by: Luo Chongjun <luochongjun@gl-inet.com>
Keith Harrison [Sat, 7 Jan 2023 15:23:03 +0000 (10:23 -0500)]
ramips: add support for D-Link DIR-1935 A1
Add support for D-Link DIR-1935 A1 based on similarities to DIR-882 A1,
DIR-867 A1 and other DIR-8xx A1 models. Existing DIR-882 A1 openwrt
"factory" firmware installs without modificaitons via the D-Link
Recovery GUI and has no known incompatibilities with the DIR-1935 A1.
Changes to be committed:
new file: target/linux/ramips/dts/mt7621_dlink_dir-1935-a1.dts
modified: target/linux/ramips/image/mt7621.mk
modified: target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
Specifications:
* Board: Not known
* SoC: MediaTek MT7621 Family
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615 Family (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
WiFi 5G (green)
Notes:
* 160MHz 5GHz is available in LuCi but does not appear to work (i.e. no
SSID is visible in wifi scanning apps on other devices) with either
official DIR-882 A1 firmware or a test build for the DIR-1935 A1 based
on the 22.03.2 branch. 80 MHz 5GHz works.
Serial port:
* Untested (potential user damage/error)
* Expected to be identical to other DIR-8xx A1 models:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
2 - RXD
3 - TXD
4 - GND
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Keith Harrison <keithh@protonmail.com>
Jo Deisenhofer [Fri, 2 Dec 2022 15:41:13 +0000 (16:41 +0100)]
ramips: add support for xiaomi RA75 Range Extender
This device is a 'Range extender' variant of the Xiaomi 4A router.
Its identical to the 100m non-intl/chinese version as much as it can run
the same firmware, differences being form factor, LEDs, WPS button
and one 100M port only.
The stock firmware differs significantly, being 'app managed only'.
MAC Addresses
-------------
All 3 MACs are read from flash and identical to stock.
Label MAC is WIFI 2G
Installation
------------
No HTML UI on this device, serial console only. The serial connector
is unpopulated but standard size and clearly marked. Flash from the
U-Boot shell at boot by choosing (2) and flashing the sysupgrade file
via tftp.
Recovery/Debricking procedures of the xiaomi 4A and variants should
work, but there currently is no official source for the stock firmware.
Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
pressing 't'
3. Load and run OpenWrt initramfs image:
tftpboot
bootm
4. Once inside OpenWrt, switch to the first boot image:
fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv BootImage 1
reboot
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
the OEM firmware
MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
| | MAC example 1 | MAC example 2 | Algorithm |
+---------+-------------------+-------------------+-------------+
| label | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| LAN | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WAN | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2 |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).
Notes
-----
[1] WAN MAC address:
a. First octet of WAN MAC is differ than others and OUI is not related
to TP-Link company. This probably should be fixed.
b. Flipping bits in first octet and hex delta are different for the
different MAC examples:
+-----------------+----------------+----------------+
| | Example 1 | Example 2 |
+-----------------+----------------+----------------+
| LAN | 68 = 0110 1000 | 50 = 0101 0000 |
| MAC (1st octet) | ^ ^ ^ | |
+-----------------+----------------+----------------+
| WAN | 72 = 0111 0010 | 54 = 0101 0100 |
| MAC (1st octet) | ^ ^ ^ | ^ |
+-----------------+----------------+----------------+
| HEX delta | 0xa | 0x4 |
+-----------------+----------------+----------------+
| DEC delta | 4 | 4 |
+-----------------+----------------+----------------+
c. DEC delta is a constant (4). This looks like a mistake in OEM
firmware and probably should be fixed.
Based on the above, I decided to keep correct OUI and make WAN MAC =
label + 1.
[2] Bootloaders
The device contains 3 bootloaders:
- First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
located on NAND Flash to load next full-feature Uboot.
- Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
bootloader includes recovery webserver. Requires special uImages to
continue the boot process:
0x00 (os0, os1) - firmware uImage
0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
- Additionally, both slots of the original TP-Link firmware contains
Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
magics and CRCs. We don't use this U-Boot with OpenWrt.
INAGAKI Hiroshi [Sat, 1 Oct 2022 12:10:33 +0000 (21:10 +0900)]
ramips: separate and update dtsi of ELECOM WRC-2533GHBK-I/GHBK2-T
ELECOM WRC-2533GHBK2-T has the almost same hardware as WRC-2533GHBK-I,
so separate the common parts from dts to dtsi.
Additionaly, add color/function properties to LED nodes and change the
trigger of wlan2g/wlan5g LED to "phy*tpt" trigger.
This is an RTL8393-based switch with 48 RJ-45 and 2 SFP ports.
Hardware
--------
SoC: Realtek RTL8393M
RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI)
FLASH: 8MB NOR (Macronix MX25L6433F)
ETH: 48x 10/100/1000 Mbps RJ-45 Ethernet
SFP: 2x SFP
BTN:
- 1x Reset button
LEDS:
- 50x Green-Amber leds: lan/sfp status
- 1x Green led: power (Always on)
UART:
- 115200-8-N-1 (CN3, pin-out on PCB)
Everything works correctly except for the 2 SFP ports that are not
working unless you enable it every boot in U-Boot with the command:
rtk network on
Installation
------------
You can install Openwrt using one of the following methods.
Warning: flashing OpenWrt will delete your current configuration.
Warning 2: if the -factory.bix file is not available anymore, you must
follow Method 2.
Method 1:
Check the firmware version currently running on your switch. If you are
running FW V1.0.1.10 or greater, you have to download the firmware
V1.0.1.8 from Netgear website and then flash this version. When the
switch restarts, it should be on version V1.0.1.8. Now you can get the
OpenWrt -factory.bix file and then flash it using the OEM web interface.
Method 2 (requires the UART connection):
Boot the -initramfs-kernel.bin image from U-Boot with these commands:
rtk network on;
tftpboot 0x8f000000 openwrt-realtek-rtl839x-netgear_gs750e-initramfs-kernel.bin;
bootm;
And then flash the -sysupgrade.bin file from OpenWrt.
Revert to stock
---------------
Get the stock firmware from the Netgear website and flash it using the
OpenWrt web interface. Remember to not keep the current configuration
and check the "Force upgrade" checkbox
Once reverted to stock the firmware could complain in the UART console
about mtdblock3 and/or mtdblock4 not being mounted correctly but it
seems to work anyway without any problems. Sample error:
mount: Mounting /dev/mtdblock4 on /mntlog failed: Input/output error
If you want to get rid of these error messages you can boot the
-initramfs-kernel.bin image from U-Boot with these commands:
rtk network on;
tftpboot 0x8f000000 openwrt-realtek-rtl839x-netgear_gs750e-initramfs-kernel.bin;
bootm;
And then erase the corresponding partitions using the command:
For mtdblock3:
mtd erase jffs2_cfg
For mtdblock4:
mtd erase jffs2_log
Now you can reboot the switch and the errors should be gone
Note
----
To get the SFP ports fully working, all the right GPIOs must be found.
In the GPL sources I found these:
- GPIO_14: SFP_TX_DIS1;
- GPIO_19: SFP_TX_DIS0;
Sander Vanheule [Fri, 13 Jan 2023 21:16:58 +0000 (22:16 +0100)]
image: add FACTORY_SIZE to DEFAULT_DEVICE_VARS
FACTORY_SIZE is used as a device recipe variable on both the D-Link
DIR-825-B1 and Trendnet TEW-673GRU, but is not listed as a device
variable, neither globally, nor for ath79. Being assigned the same
value, this probably hasn't caused any issues.
Add FACTORY_SIZE to the global list DEFAULT_DEVICE_VARS, to ensure the
variable is reset for every device, and to allow it to be used outside
of the ath79 target.
Linhui Liu [Thu, 12 Jan 2023 08:27:06 +0000 (16:27 +0800)]
tools/patchelf: update to 0.17.2
Changes from version 0.17.1 to version 0.17.2:
- fix incorrect version in 0.17.1
Changes from version 0.17.0 to version 0.17.1:
- Also pass STRIP to the tests
- Fix Out-of-bounds read in the function modifySoname
- Split segment size fix
Robert Marko [Wed, 11 Jan 2023 21:42:34 +0000 (22:42 +0100)]
mac80211: ath11k: fix monitor bringup
Currently, ath11k will crash the crash if we try to bringup the monitor
mode interface.
Luckily, it has already been fixed upstream, so backport the patches
fixing it.
Fixes: 93ae4353cdf6 ("mac80211: add ath11k PCI support") Signed-off-by: Robert Marko <robimarko@gmail.com>
scripts/dl_github_archieve.py: fix generating unreproducible tar
Allign dl_github_archieve.py to 8252511dc0b5a71e9e64b96f233a27ad73e28b7f
change. On supported system the sigid bit is applied to files and tar
archieve that on tar creation. This cause unreproducible tar for these
system and these bit should be dropped to produce reproducible tar.
Add the missing option following the command options used in other
scripts.
Fixes: 75ab064d2b38 ("build: download code from github using archive API") Suggested-by: Eneas U de Queiroz <cotequeiroz@gmail.com> Tested-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There is currently a problem with making reproducible version of lldpd.
The tool version is generated based on 3 source:
1. .dist-version file in release tar
2. git hash with presence of .git directory
3. current date
Using the codeload tar from github results in getting the repo without
the .git directory and since they are not release tar, we don't have
.dist-version. This results in having lldpd bin with a version set to
the current build time.
Switch to release tar so that we correctly have a .dist-version file and
the version is not based on the build time.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
Michal Hrusecky [Mon, 9 Jan 2023 14:59:02 +0000 (15:59 +0100)]
mvebu: backport upstream patch to fix COMPHY reset
Upstream commit [1] included in the Linux kernel version 6.2 was
backported to Linux kernels 6.1.4, 6.0.18. It should be possible that it
is going to be backported even to the 5.15 series, but before it happens,
let's include it here.
It was discovered that on SOC Marvell Armada 3720, which is using e.g.
Turris MOX, and if you are also using it with older ARM Trusted Firmware
v1.5, it is not possible to detect connected USB 3.0 devices, but they
are working just fine when connected with USB 2.0 cable. This patch
fixes it.
Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Michal Hrusecky <michal.hrusecky@turris.com> Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[improve commit description, added tag to the patch]
CI: kernel: test each target with additional changes than target/linux
Test each target if there are additional changes than target/linux.
This is needed to do wide test with changes to kmods, include/kernel and
changes to the workflow files.
While at it also cleanup and rework the code to drop duplication.
Also drop since_last_remote_commit to better track changes.
Fixes: 04ada8bc4118 ("CI: kernel: build only changed targets") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
We've few low spec (make -j3) build workers attached to the 22.03
buildbot instance which from time to time exhibit following build
failure during image generation (shortened for brewity):
+ dd bs=512 if=root.ext4 of=openwrt-22.03...sdcard.img.gz.img
dd: failed to open 'root.ext4': No such file or directory
Thats happening likely due to the fact, that on buildbots we've
`TARGET_PER_DEVICE_ROOTFS=y` which produces differently named filesystem
image in the SD card image target dependency chain:
and that hardcoded `root.ext4` image filename becomes available from
other Make targets in the later stages. So lets fix this issue by using
IMAGE_ROOTFS Make variable which should contain proper path to the root
filesystem image.
Petr Štetiar [Tue, 3 Jan 2023 11:44:51 +0000 (12:44 +0100)]
at91: sama7: fix racy SD card image generation
We've few low spec (make -j3) build workers attached to the 22.03
buildbot instance which from time to time exhibit following build
failure during image generation:
+ dd bs=512 if=root.ext4 of=openwrt-22.03-snapshot-r20028-43d71ad93e-at91-sama7-microchip_sama7g5-ek-ext4-sdcard.img.gz.img seek=135168 conv=notrunc
dd: failed to open 'root.ext4': No such file or directory
Thats likely due to the fact, that on buildbots we've
`TARGET_PER_DEVICE_ROOTFS=y` which produces differently named filesystem
image in the SD card image target dependency chain:
and that hardcoded root.ext4 becomes available from other target in the
later stages. So lets fix this issue by using IMAGE_ROOTFS Make variable
which should contain proper path to the root filesystem image.
Add concurrency limits for pull request test so that on pull request
refresh old jobs are cancelled.
The group is created based on the github ref + workflow name and the
workflow is cancelled only it it comes from a pull_request event.
Push events are not affected by this limit.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
treewide: derive host and hostpkg path from STAGING_DIR
STAGING_DIR may be provided from command line. We currently hardcoded
STAGING_DIR_HOST and STAGING_DIR_HOSTPKG to the default location but we
currently have some relocatable patch that derive the path from
STAGING_DIR.
Fix this and correctly derive STAGING_DIR_HOST and STAGING_DIR_HOSTPKG
from STAGING_DIR.
The intention is to fix inconsistency from the relocatable patch and the
use of STAGING_DIR_HOST that is always hardcoded.
This with a wrong configuration may end up in broken state with some
host tools expecing a PATH from STAGING_DIR and others using library
from the default staging_dir/host path.
To save downstream project the original implementation is saved while
fixing the inconsistency between patch and .mk.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Config evaluation require default with if to be put before the generic
default config with no condition. Putting the default config before any
conditional default results in always selecting the non conditional one.
This results in the version be hardcoded to gcc 12 even if gcc 11 is
selected in the Advanced build options.
Fix this by putting the gcc 12 default option as last after ANY
conditional default config.
Fixes: d9de5252a44e ("toolchain/gcc: switch to version 12 by default") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Felix Fietkau [Sun, 8 Jan 2023 19:38:40 +0000 (20:38 +0100)]
ucode: update to the latest version
34cfbb922c96 README.md: various spelling and documentation fixes ff32355ea645 build: make rtnl/nl80211 depend on linux instead of !APPLE c0e413c21f7b include: add uc_fn_thisval() 1e4d20932646 Merge pull request #134 from nbd168/thisval
Hauke Mehrtens [Mon, 19 Dec 2022 00:47:48 +0000 (01:47 +0100)]
toolchain/gcc: switch to version 12 by default
This was build tested with all core packages on all targets
successfully.
Most packages from the feed are also building fine.
This was run tested on the following systems:
* lantiq/xrx200 musl
* pistachio/generic musl
* sunxi/cortexa53 musl
* x86/64 musl
* x86/64 glibc
* armvirt/64 musl
The size of the images stays more or less the same for MIPS BE and
aarch64. I haven't tested other architectures.
With GCC 11 I got these sizes for lantiq/xrx200:
7,219,848 openwrt-lantiq-xrx200-tplink_tdw8970-initramfs-kernel.bin
7,472,208 openwrt-lantiq-xrx200-tplink_tdw8970-squashfs-sysupgrade.bin
With GCC 12 I got these sizes for lantiq/xrx200:
7,217,355 openwrt-lantiq-xrx200-tplink_tdw8970-initramfs-kernel.bin
7,406,674 openwrt-lantiq-xrx200-tplink_tdw8970-squashfs-sysupgrade.bin
The sysupgrade image is probably padded. The initramfs image is 0.03% smaller.
With GCC 11 I got these sizes for armvirt/64:
4,143,943 openwrt-armvirt-64-default-rootfs.tar.gz
10,887,176 openwrt-armvirt-64-Image
24,911,880 openwrt-armvirt-64-Image-initramfs
4,141,572 openwrt-armvirt-64-rootfs.cpio.gz
4,255,854 openwrt-armvirt-64-rootfs-ext4.img.gz
3,391,178 openwrt-armvirt-64-rootfs-squashfs.img.gz
With GCC 12 I got these sizes for armvirt/64:
4,142,778 openwrt-armvirt-64-default-rootfs.tar.gz
10,887,176 openwrt-armvirt-64-Image
24,911,880 openwrt-armvirt-64-Image-initramfs
4,138,105 openwrt-armvirt-64-rootfs.cpio.gz
4,255,463 openwrt-armvirt-64-rootfs-ext4.img.gz
3,390,390 openwrt-armvirt-64-rootfs-squashfs.img.gz
Hauke Mehrtens [Mon, 19 Dec 2022 23:58:19 +0000 (00:58 +0100)]
toolchain/gcc: Fix GCC version check
The version check which sets GCC_VERSION_FILE to the correct value only
worked when the advanced options menu was active and not when it was not
active.
Hauke Mehrtens [Mon, 19 Dec 2022 00:40:04 +0000 (01:40 +0100)]
rtl8812au-ct: Ignore address errors
GCC 12.2.0 shows these error messages:
````
rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c: In function 'rtw_mfree_stainfo':
rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c:210:24: error: the comparison will always evaluate as 'true' for the address of 'lock' will never be NULL [-Werror=address]
210 | if(&psta->lock != NULL)
| ^~
In file included from rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:109,
from rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c:22:
rtl8812au-ct-2021-11-07-39df5596/include/sta_info.h:95:17: note: 'lock' declared here
95 | _lock lock;
| ^~~~
````
````
CC [M] rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.o
rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c: In function 'cfg80211_rtw_scan':
rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c:2176:32: warning: the comparison will always evaluate as 'true' for the address of 'ssid' will never be NULL [-Waddress]
2176 | if(ssids->ssid != NULL
| ^~
In file included from rtl8812au-ct-2021-11-07-39df5596/include/osdep_service_linux.h:88,
from rtl8812au-ct-2021-11-07-39df5596/include/osdep_service.h:41,
from rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:32,
from rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c:22:
/home/hauke/openwrt/openwrt/staging_dir/target-mips_24kc_musl/usr/include/mac80211/net/cfg80211.h:2364:12: note: 'ssid' declared here
2364 | u8 ssid[IEEE80211_MAX_SSID_LEN];
| ^~~~
````
````
CC [M] rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.o
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c: In function 'phydm_cmd_parser':
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c:873:28: warning: the comparison will always evaluate as 'true' for the pointer operand in 'input + ((sizetype)i + 1) * 16' must not be NULL [-Waddress]
873 | if(input[i+1]) {
| ^~~~~
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c:894:28: warning: the comparison will always evaluate as 'true' for the pointer operand in 'input + ((sizetype)i + 1) * 16' must not be NULL [-Waddress]
894 | if(input[i+1]) {
| ^~~~~
````
This one was only seen on the rockchip/armv8 target:
````
CC [M] rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.o
In function '__nat25_add_pppoe_tag',
inlined from 'nat25_db_handle' at rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:909:10:
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:118:9: error: 'memcpy' reading between 2052 and 9220 bytes from a region of size 40 [-Werror=stringop-overread]
118 | memcpy((unsigned char *)ph->tag, tag, data_len);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c: In function 'nat25_db_handle':
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:878:63: note: source object 'tag_buf' of size 40
878 | unsigned char tag_buf[40];
| ^~~~~~~
````
Most of them are looking like real errors to me, but some fixes need a
deeper understanding of the driver and probably bigger changes to the driver.
Ignore these error messages for now. It would be nice if someone would
fix them.
Hauke Mehrtens [Mon, 19 Dec 2022 00:19:32 +0000 (01:19 +0100)]
uqmi: Ignore wrong maybe-uninitialized and dangling-pointer error
GCC 12.2.0 shows this false positive error message:
````
uqmi-2022-05-04-56cb2d40/dev.c: In function 'qmi_request_wait':
uqmi-2022-05-04-56cb2d40/dev.c:217:23: error: storing the address of local variable 'complete' in '*req.complete' [-Werror=dangling-pointer=]
217 | req->complete = &complete;
| ~~~~~~~~~~~~~~^~~~~~~~~~~
uqmi-2022-05-04-56cb2d40/dev.c:208:14: note: 'complete' declared here
208 | bool complete = false;
| ^~~~~~~~
uqmi-2022-05-04-56cb2d40/dev.c:208:14: note: 'req' declared here
cc1: all warnings being treated as errors
````
and this one:
````
In file included from uqmi-2022-05-04-56cb2d40/commands.c:28:
In function 'blobmsg_close_table',
inlined from 'cmd_nas_get_cell_location_info_cb' at /home/haukeuqmi-2022-05-04-56cb2d40/commands-nas.c:897:4:
/usr/include/libubox/blobmsg.h:256:9: error: 'c' may be used uninitialized [-Werror=maybe-uninitialized]
256 | blob_nest_end(buf, cookie);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from uqmi-2022-05-04-56cb2d40/commands.c:169:
uqmi-2022-05-04-56cb2d40/commands-nas.c: In function 'cmd_nas_get_cell_location_info_cb':
uqmi-2022-05-04-56cb2d40/commands-nas.c:713:15: note: 'c' was declared here
713 | void *c, *t, *cell, *freq;
| ^
cc1: all warnings being treated as errors
````
Hauke Mehrtens [Mon, 19 Dec 2022 00:07:38 +0000 (01:07 +0100)]
elfutils: Ignore wrong use-after-free error
GCC 12.2.0 shows this false positive error message:
````
In function 'bigger_buffer',
inlined from '__libdw_gunzip' at gzip.c:374:12:
gzip.c:96:9: error: pointer may be used after 'realloc' [-Werror=use-after-free]
96 | b = realloc (state->buffer, more -= 1024);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
gzip.c:94:13: note: call to 'realloc' here
94 | char *b = realloc (state->buffer, more);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
````
projects / thirdparty / openwrt.git / log
