After migrating to kernel 5.15, upgrading causes the units to become
soft-bricked, hanging forever at the kernel startup.
Kernel size limitation of 4000000 bytes is suspected here, but this is
not fully confirmed.
Disable the images to protect users from inadvertent bricking of units,
because recovery of those is painful with Cisco's U-boot, until the root
cause is found and fixed.
Previously both lan1 and lan2 leds were wrongly labelled as lan2.
Moreover they were connected to the wrong lan port.
Fixes 8fde82095ba0 ("ramips: add support for Wavlink WL-WN535K1")
Reported-by: Nicolò Maria Semprini <nicosemp@gmail.com> Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
(cherry picked from commit c71dada92654a53c63bbc5bebcc40fe924750ed7)
Installation:
* Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
be directly used to install OpenWrt. Firmware must be upgraded using the
'force' and 'do not save configuration' command line options (or
correspondig web interface checkboxes) since the vendor firmware is from
the pre-DSA era.
Recovery Mode:
* Press reset button, power up the device, wait for about 10sec.
* Upload sysupgrade image through the firmware recovery mode web page at
192.168.1.1.
netfilter: fix typo in nf-socket and nf-tproxy kconfig
Fix a typo where the wrong KCONFIG was used and fix selecting the
correct kernel config option to use these packages.
Fixes: 4f443c885ded ("netfilter: separate packages for kmod-ipt-socket and kmod-ipt-tproxy") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3ebebf08be950a8a0f3bf5b2c3db910621f2cc21)
David Bauer [Wed, 17 May 2023 10:04:00 +0000 (12:04 +0200)]
mac80211: always use mac80211 loss detection
ath10k does not report excessive loss in case of broken block-ack
sessions. The loss is communicated to the host-os, but ath10k does not
trigger a low-ack events by itself.
The mac80211 framework for loss detection however detects this
circumstance well in case of ath10k. So use it regardless of ath10k's
own loss detection mechanism.
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap105.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
The Arcadyan AR7516, AKA Orange Bright Box or EE Bright Box 1, is a wifi
fast ethernet router, 2.4 GHz single band with two internal antennas. It
comes with a horizontal stand black shiny casing.
Newer Bright Box 1 model stands vertically, and comes with a totally
different board inside, not compatible with this firmware.
Installation in two steps, new CFE bootloader and firmware:
Install new CFE:
1. Power off the router and press the RESET button
2. Power on the router and wait some seconds
3. Release the RESET button
3. Browse to http://192.168.1.1, this web interface will offer both
firmware (“Software”) upgrade and bootloader upgrade; be sure to
use the bootloader section of the upload form.
4. Upload the new CFE (availabe at the wiki page)
5. Wait about a minute for flashing to finish and reboot into the new bootloader.
Install OpenWrt via new CFE web UI:
1. After installing the new CFE, visit http://192.168.1.1
2. Upload the Openwrt cfe firmware
5. Wait a few minutes for it to finish
This patch initially introduced in 94b4da9b4aaded6ed8a5bd93bf38a7c92753fe68
breaks mvebu devices when using vlan filtering with kernel 5.15 or 6.1,
it was working ok in 5.10.
With this patch, frame that should exit untagged from the switch exit tagged.
Running 'tcpdump -Q out -evnnli eth1' (eth1 being the dsa interface)
- with the hack, frame is sent directly to the
destination port 4 with VID 2, so the switch leave the tag as instructed:
11:22:33:44:55:66 > 77:88:99:aa:bb:cc, Marvell EDSA ethertype 0xdada (Unknown), rsvd 0 0, mode From CPU, target dev 0, port 4, tagged, VID 2, FPri 0, ethertype ARP (0x0806), length 50: Ethernet (len 6), IPv4 (len 4), Request who-has 5.6.7.8 tell 1.2.3.4, length 28
- without the hack, frame is sent to the switch that
performs the forwarding decision and untagging:
11:22:33:44:55:66 > 77:88:99:aa:bb:cc, Marvell EDSA ethertype 0xdada (Unknown), rsvd 0 0, mode Forward, dev 1, port 0, tagged, VID 2, FPri 0, ethertype ARP (0x0806), length 50: Ethernet (len 6), IPv4 (len 4), Request who-has 5.6.7.8 tell 1.2.3.4, length 28
Removing this patch makes my Turris Omnia usable with vlan filtering,
ie wifi device can talk to wired device again.
Using kernel 5.15 some broadcast/multicast traffic is still leaked
(on a VLAN 2 access port I see tagged VLAN 3 frame),
using kernel 6.1 fixes that.
People needing the extra performance should try the bridger package.
Acked-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 244328b19c3943bb145b72f0d85062f535e56fbd)
Installation via CFE web UI:
1. Power off the router and press the RESET button
2. Power on the router and wait 12 or more seconds
3. Release the RESET button
4. Browse to http://192.168.1.1 and upload the Openwrt cfe firmware
5. Wait a few minutes for it to finish
bmips: enable the data Read Ahead Cache for BMIPS4350
The data RAC is left disabled by the bootloader in some SoCs, at least in
the core it boots from. Enabling this feature increases the performance up
to +30% depending on the task.
The kernel enables the whole RAC unconditionally on BMIPS3300 CPUs. Enable
the data RAC in a similar way also for BMIPS4350.
Tested on DGND3700 v1 (BCM6368) and HG556a (BCM6358).
Installation (fw 2.0.9)
-----------------------
1. Login to the web interface under SuperUser (root) credentials.
Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
device written on the backplate stick.
2. Navigate to Setting -> WAN. Add:
Name - WAN1
Connection Type - Static
IP Address - 172.16.0.1
Netmask - 255.255.255.0
Save -> Apply. Set default: WAN1
3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
Protocol - SSH
Port - 22
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN Interface - WAN1
Save ->Apply
Add:
Protocol - HTTP
Port - 80
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN interface - WAN1
Save -> Apply
4. Set up your PC ethernet:
Connection Type - Static
IP Address - 172.16.0.2
Netmask - 255.255.255.0
Gateway - 172.16.0.1
5. Connect PC using ethernet cable to the WAN port of the router
6. Connect to the router using SSH shell under SuperUser account
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 171.16.0.2
Recovery
--------
Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery
MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:e8 |
| WAN | label + 1 | *:e9 |
| 2g | label + 4 | *:ec |
| 5g | label + 5 | *:ed |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
This improves compatibility with the elder stock firmwares of the
following devices, which have not yet been merged into OpenWrt:
- Beeline SmartBox Pro
- Beeline SmartBox Turbo+
- WiFire S1500.NBN
Without this, OpenWrt factory image installation may fail.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> Signed-off-by: Maximilian Weinmann <x1@disroot.org>
(cherry picked from commit 35a4418d3966ccf6229916b0021bd18871ef22dd)
* Modified to define the variable i as suggested by DragonBluep in PR discussion.
See: https://github.com/openwrt/openwrt/pull/12823#issuecomment-1578518576
ipq806x: set PERFORMANCE as the default cpufreq governor
Move default cpufreq governor from ONDEMAND to PERFORMANCE. The temp
increase is just 2°C and Watt usage the change is minimal in the order
of additional millwatt. The SoC and krait in general looks to suffer for
some problem with cache scaling. To have better system stability, force
cpu freq and cache freq to the max value supported by the system. This
follows mvebu platform where cpufreq is broken and cause minimal
temp/watt increase.
User can still tweak the governor to ondemand using sysfs entry if
needed.
Fixes: 9ceeaf4c6cac ("brcm63xx: switch to hardware led controllers") Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit 0e01ba93610240ad84f9bbc5fc6e5982a07d39f9)
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Installation via OEM web UI:
1. Use the admin credentials to login via web UI
2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
3. Press "Update Firmware" button and wait some minutes until it finish
The HPNA hardware probably needs a firmware to make the coaxial port work.
In the OEM firmware, it's apparently sent with an utility (inhpna) through
the ethernet port.
Installation via CFE web UI:
1. Connect the UART serial port.
2. Power on the router and press enter at the console prompt to stop the
bootloader.
4. Browse to http://192.168.1.1 and upload the OpenWrt CFE firmware
5. Wait a few minutes for it to finish
base-files: upgrade: nand: add JFFS2 cleanmarkers support
Some Broadcom MIPS devices require JFFS2 cleanmarkers to be present on the
kernel partition or the bootloader will identify the partition as corrupt and
won't boot the kernel.
The DGND3700v2 renames the cferam bootloader from cferam to cfeXXX, where XXX
is the number of firmware upgrades performed by the bootloader. Other bcm63xx
devices rename cferam.000 to cferam.XXX, but this device is special because
the cferam name isn't changed on the first firmware flashing but it's changed
on the subsequent ones.
Therefore, we need to look for "cfe" instead of "cferam" to properly detect
the cferam partition and fix the bootlop.
The DGND3700v2 renames the cferam bootloader from cferam to cfeXXX, where XXX
is the number of firmware upgrades performed by the bootloader. Other bcm63xx
devices rename cferam.000 to cferam.XXX, but this device is special because
the cferam name isn't changed on the first firmware flashing but it's changed
on the subsequent ones.
Therefore, we need to look for "cfe" instead of "cferam" to properly detect
the cferam partition and fix the bootlop.
Some devices rename cferam bootloader using specific patterns and don't follow
broadcom standards for renaming cferam files. This requires supporting
different cferam file names.
Zoltan HERPAI [Sun, 16 Dec 2018 10:05:58 +0000 (11:05 +0100)]
sifiveu: add new target for SiFive U-based boards
RISC-V is a new CPU architecture aimed to be fully free and open. This
target will add support for it, based on 5.15.
Supports running on:
- HiFive Unleashed - FU540, first generation
- HiFive Unmatched - FU740, current latest generation, PCIe
SD-card images are generated, where the partitions are required to have
specific type codes. As it is commonplace nowadays, OpenSBI is used as the
first stage, with U-boot following as the proper bootloader.
Add patch until it gets accepted in firmware-utils upstream.
The SiFive RISC-V SoCs use two special partition types in the boot process.
As a first step, the ZSBL (zero-stage bootloader) in the CPU looks for a
partition with a GUID of 5B193300-FC78-40CD-8002-E86C45580B47 to load the
first-stage bootloader - which in OpenWrt's case is an SPL image. The FSBL
(SPL) then looks for a partition with a GUID of 2E54B353-1271-4842-806F-E436D6AF6985 to load the SSBL which is usually an
u-boot.
With ptgen already supporting GPT partition creation, add the required GUID
types and name them accordingly to be invoked with the '-T <GPT partition
type>' parameter.
Zoltan HERPAI [Sun, 26 Jan 2020 22:45:48 +0000 (23:45 +0100)]
opensbi: add package for RISC-V
OpenSBI is a form of a first-stage bootloader, which initializes
certain parts of an SoC and then passes on control to the second
stage bootloader i.e. an u-boot image.
We're introducing the package with release v1.2, which provides
SBI v0.3 and the SBI SRST extensions which helps to gracefully
reboot/shutdown various HiFive-U SoCs.
Petr Štetiar [Fri, 2 Jun 2023 11:54:20 +0000 (13:54 +0200)]
u-boot.mk: add support for config customization
Make it possible to easily customize U-Boot config options via new
`UBOOT_CUSTOMIZE_CONFIG` variable, so we don't need to patch config
files or override config step with shell hackery.
This generic approach uses `config` CLI to tweak the .config as needed,
for example:
Mathew McBride [Wed, 5 Oct 2022 01:40:22 +0000 (12:40 +1100)]
kernel: kmod-amazon-ena: move to top level netdevices
The Amazon ENA network devices are also used on the
AWS Arm (Graviton) instance types, so move it from
the x86-only module file to the top level netdevices.
Mathew McBride [Mon, 13 Feb 2023 06:51:26 +0000 (06:51 +0000)]
armvirt: 64: disable CONFIG_SMC91X
The SMC91X family is a ISA-age Ethernet controller.
I'm not particularly sure what it's doing in armvirt/64,
as it's unlikely there is a QEMU or real hardware configuration
that exists with it.
armvirt: config changes required for framebuffer console
These Kconfig options are required to get a screen console
working with the VMware Fusion ARM (Apple Silicon) preview.
They are likely to be the same for other Arm standard
"desktop" hardware that may emerge.
Anton Antonov [Thu, 22 Dec 2022 12:01:59 +0000 (12:01 +0000)]
armvirt: 64: Add storage support for qemu-sbsa platform
Enable SATA support, which is used by the Server Base
System Architecture reference board[1].
Signed-off-by: Anton Antonov <Anton.Antonov@arm.com> Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://qemu.readthedocs.io/en/latest/system/arm/sbsa.html
(23.05/5.15 version of 26905c96124af10a795167509116252e9357baea)
Anton Antonov [Thu, 22 Dec 2022 12:00:12 +0000 (12:00 +0000)]
armvirt: 64: Add NXP i.MX 8M Mini/Nano/Quad/Plus EVK support
Also includes Advantech RSB-3720 (iMX8 Plus) support.
Signed-off-by: Anton Antonov <Anton.Antonov@arm.com> Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Re-sort into kernel config, move network into modules]
(23.05/5.15 version of commit 3efb3b801bb1393897ff58b9af3753157f28f441)
armvirt: 64: add support for other SystemReady-compatible vendors
These changes are to support other vendors that have SystemReady/EFI
support, including:
* Marvell Armada
** (This is speculative as I don't have a machine of my own to test)
* Amazon Graviton (tested bare-metal and virtualized instances)
* VMware (Fusion for ARM Mac preview)
* NXP/Freescale (Layerscape series not already selected)
* HiSilicon
* Allwinner/sunxi
* Rockchip (untested, options taken from arm64 defconfig)
To give an idea of the hardware certified for SystemReady,
see
https://www.arm.com/architecture/system-architectures/systemready-certification-program/ir
and
https://www.arm.com/architecture/system-architectures/systemready-certification-program/es
Other vendors that _should_ work include Marvell Octeon 10
and Ampere. I understand these systems should work
"out of the box" in ACPI mode but may require other drivers
(e.g PCIe NICs and storage controllers).
This fixes an issue with NXP's DPAA2 platforms (LS1088/2088/LX2160)
* A deadlock issue when attempting to detach the SFP management from
a PHY interface (e.g when trying to reboot). These issues were fixed
in kernel 6.2[1], but it's version does not cleanly apply onto 5.15.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - see patch series "Fix rtnl_mutex deadlock with DPAA2 and SFP modules",
https://patchwork.kernel.org/project/netdevbpf/cover/20221129141221.872653-1-vladimir.oltean@nxp.com/
Mathew McBride [Tue, 1 Jun 2021 01:48:25 +0000 (01:48 +0000)]
build: use 128MiB as the boot/kernel partition size on armvirt target
The nominal partition type for EFI boot partitions is FAT32,
which has a minimum size of 32MiB on a 512-byte-sector block device.
To ensure that the boot partition is created as FAT32 set a size
well above this minimum.
A useful discussion about EFI partition sizes can be found here:
https://superuser.com/questions/1310927/what-is-the-absolute-minimum-size-a-uefi-system-partition-can-be
I have found 128MiB works pretty consistently across both
tools (mkfs.fat) and firmwares (EDKII)
scripts: gen_image_generic: allow the partition types to be set
The use case for this is to set the kernel partition as the
EFI system partition. Versions of U-Boot with the
EFI boot manager (eficonfig and efidebug commands) will
store their boot order data on the ESP.
Mathew McBride [Wed, 19 Jan 2022 03:24:45 +0000 (03:24 +0000)]
armvirt: update README with new image names
The introduction of EFI support has changed how armvirt
images are generated. The kernel and filesystem binaries
can still be used as before with QEMU directly.
armvirt: disable LD dead code elimination on ARM32
This interferes with the generation of the EFI stub section for
ARM32. As this target is not size constrained, disable the dead code
data elimination hack.
Its currently impossible to flash/recover the device using that image as
losetup is missing:
root@OpenWrt:/# sysupgrade -v /tmp/openwrt-ipq807x-generic-prpl_haze-squashfs-sysupgrade.bin
...
/lib/upgrade/do_stage2: line 38: losetup: not found
Failed to detach all loop devices. Skip this try.
So lets fix it by including the needed utils for sysupgrade in
DEFAULT_PACKAGES set.
- ARM Standard 20-pin 2.54mm/0.1" JTAG (1V8 !!!)
- Bluetooth v5.0 + EDR with integrated Class 1 PA (CYW20704)
- 1x M.2 B-key socket with PCIe 3.0
- 1x USB 3.0 port
- UART marked J6 is 4-pin 2.54mm/0.1" connector 3V3(arrow),RX,TX,GND (115200 8N1)
- Reset and WPS buttons
Flashing instructions:
1. From U-Boot boot OpenWrt using initramfs image:
* SFP feature not implemented/tested
* M.2 feature not implemented/tested
* Bluetooth feature not implemented/tested
* 6GHz wireless should be working, but not tested
* MAC address assigments for LAN interfaces
Petr Štetiar [Mon, 5 Jun 2023 10:06:41 +0000 (12:06 +0200)]
ipq-wifi: update to version 2023-06-03
Contains following updates:
* ipq8074: update RegDB in new submitted BDF
* Revert "ipq8074: update RegDB in new submitted BDF"
* qcn9074: update RegDB in new submitted BDF
* ipq8074: update RegDB in new submitted BDF
* qca-wireless: ipq40xx: add BDFs for ZTE MF287+
* Add BDFs for prpl Foundation Haze board
Michael Pratt [Tue, 30 May 2023 09:43:00 +0000 (05:43 -0400)]
tools/findutils: define list of installed programs
Define the variable PKG_PROGRAMS for the list
of programs installed by findutils,
which will create a stampfile for each
through a new feature in host-build.mk.
Michael Pratt [Tue, 30 May 2023 11:20:19 +0000 (07:20 -0400)]
host-build: add support for a stampfile per installed binary
Some individual build items install a group of programs
instead of a program matching the name of the build item.
Add support for installing stampfiles for each of the
programs installed by that build item,
which will allow more control and awareness
of what is installed by the rest of the build system,
if, for example, prereq symlink checks are looking
for the same program which is built already.
Michael Pratt [Mon, 29 May 2023 09:38:33 +0000 (05:38 -0400)]
prereq-build: replace relative symlinks only if broken
Some programs installed to staging_dir/host/bin
also install some symlinks to itself
for an alternative name.
Some of those new symlinks are overwriting
symlinks that were installed by prereq stage.
If prereq stage were to somehow be run again,
it should not be overwriting symlinks
that point to programs that are already built.
To filter that out, catch all symlinks
after first catching all symlinks
that have an absolute target
after all other cases in the case statement,
make sure it is not broken, and if so exit successfully.
Suggested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit b890e2fbf9211648ad4a74f3e8b47bbf04a3cc7a)
Michael Pratt [Sat, 27 May 2023 21:11:47 +0000 (17:11 -0400)]
prereq-build: do not replace binaries with symlinks
Some programs, like bash and patch, are checked by prereq stage
and have a symlink installed, but then is later built from source.
Now that the prereq-build checks are not successful
just by finding the file alone, it is possible for
a new symlink to overwrite the installed binary.
If a normal file is found in staging_dir/host/bin,
let the check look for the associated stampfile, and if found,
skip creation of a symlink and exit successfully.
Suggested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit 729909c07fae4201591e51895833112cb88485e1)
Michael Pratt [Thu, 25 May 2023 06:31:52 +0000 (02:31 -0400)]
prereq-build: fix inconsistent value of $PATH
In the recipe SetupHostCommand for checking
and creating symlinks, $PATH was only overridden
for one of several commands.
This causes the symlinks to be included
in the paths to pick a program from
when the check was repeated, because
staging_dir/host/bin was included in $PATH,
but only *sometimes*.
When the check ran again, the command succeded
with a $PATH including the symlink,
(eval "$$$$$$$$cmd")
while the path to the program was evaluated
with a $PATH NOT including the symlink,
(bin=...)
causing the symlink to be relinked incorrectly,
instead of passing as exactly the same.
Coincidentally, this was only a problem
if the symlink targeted the alternative
program with a different name.
By overriding the value of $PATH at the invocation of Make,
it will apply to the entire environment of the checks.
Petr Štetiar [Mon, 29 May 2023 17:27:15 +0000 (19:27 +0200)]
qca-nss-dp: fix oops in nss_dp_probe
Currently kernel crashes when of_phy_connect has issues:
Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000308
...
pc : phy_attached_print+0x28/0x1b0
lr : phy_attached_info+0x14/0x20
...
Call trace:
phy_attached_print+0x28/0x1b0
phy_attached_info+0x14/0x20
nss_dp_adjust_link+0x544/0x6c4 [qca_nss_dp]
of_phy_connect returns either pointer or NULL, so can't be checked with
IS_ERR macro.
Felix Fietkau [Wed, 24 May 2023 08:21:23 +0000 (10:21 +0200)]
libubox: update to the latest version
b09b316aeaf6 blobmsg: add blobmsg_parse_attr function eac92a4d5d82 blobmsg: add blobmsg_parse_array_attr ef5e8e38bd38 usock: fix poll return code check 6fc29d1c4292 jshn.sh: Add pretty-printing to json_dump 5893cf78da40 blobmsg: Don't do at run-time what can be done at compile-time 362951a2d96e uloop: fix uloop_run_timeout 75a3b870cace uloop: add support for integrating with a different event loop
Felix Fietkau [Sun, 4 Jun 2023 14:54:19 +0000 (16:54 +0200)]
unetd: update to the latest version
412d03012f13 network: prevent adding endpoint routes for addresses on the network faaf9cee6ef4 utils: fix ipv4 checksum issue 0e1c2fad3540 pex-msg: fix memory leak on fread fail in pex_msg_update_request_init 51be0ed659d0 host: fix crash parsing gateway when no endpoint is specified ca17601dc24e wg-linux: add support for splitting netlink messages for allowed ips 7d3986b7a5a2 wg-linux: increase default messages size
Robert Marko [Fri, 2 Jun 2023 12:12:01 +0000 (14:12 +0200)]
mac80211: ath11k: sync with ath-next
Synchronize the ath11k backports with the current ath-next tree.
This introduces support for MBSSID and EMA, adds factory test mode and
some new HTT stats.
Tested-by: Francisco G Luna <frangonlun@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit acde5271a68835f51185aae1b11343439a9d4cab)
Robert Marko [Fri, 2 Jun 2023 12:08:31 +0000 (14:08 +0200)]
mac80211: backport EMA beacon support
Backport EMA beacon support from kernel 6.4.
It is required for MBSSID/EMA suport in ath11k that will follow.
Tested-by: Francisco G Luna <frangonlun@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 84b5735b4c59c8fcb3db647430a4ffd574fb10a3)
Robert Marko [Fri, 2 Jun 2023 10:27:19 +0000 (12:27 +0200)]
generic: b53: rename exported symbols to avoid upstream conflict
Upstream DSA driver is exporting symbols with the same name as our
downstream swconfig driver, so lets rename the downstream symbols to make
them unique and avoid the conflict on 6.1 kernel.
Without this change, building 6.1 with kmod-switch-bcm53xx would conflict
with the B53 DSA driver and CI would fail.
kernel: fix wrong detection of Linux-Testing-Version in makefile DUMP
When the split was done, the case for testing kernel version wasn't
handled and only the to-be-compiled kernel version details files was
included. This cause the kernel Linux-Testing-Version output from
makefile target DUMP to report only the kernel version without the minor
version (example 6.1 instead of 6.1.29).
This value is expected with the full kernel version and this cause the
dump-target-info.pl script to not correctly identify if a target have a
testing kernel for the kernels calls.
Fix this regression by correctly including the kernel details files if
the target declare support for a testing kernel version.
Fixes: 0765466a42f4 ("kernel: split kernel version to dedicated files") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 595608eb3f05cba31da59e0d5d82504ab6731c0b)
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit bcdf861519)
projects / thirdparty / openwrt.git / log
