Andreas Böhler [Mon, 10 Jul 2023 09:55:30 +0000 (11:55 +0200)]
ipq4019: add support for ZTE MF287 Pro aka DreiNeo Pro
The ZTE MF287 Pro is a LTE router used (exclusively?) by the network
operator "3". It is very similar to the MF287+, but the hardware layout
and partition layout have changed quite a bit.
LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1
Installation
============
Option 1 - TFTP
---------------
TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:
Option 2 - From stock firmware
------------------------------
The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.
The exploit will be available at the device wiki page.
Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".
ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".
Option 2 - from within OpenWrt
------------------------------
This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.
Follow the commands from Option 1 to flash back to stock.
LTE Modem
=========
The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.
Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.
Other Notes
===========
Contrary to the stock firmware, the USB port on the back can be used.
There is one GPIO Switch "Power button blocker" which, if enabled, does not
trigger a reset of the SoC if the modem reboots. If disabled, the SoC is
rebooted along with the modem. The modem can be rebooted via the exported
GPIO "modem-reset" in /sys/class/gpio.
Arınç ÜNAL [Thu, 10 Aug 2023 12:23:09 +0000 (15:23 +0300)]
bcm53xx: add support for ASUS RT-AC3100
ASUS RT-AC3100 is ASUS RT-AC88U without the external switch.
OpenWrt forum users effortless and ktmakwana have confirmed that there are
revisions with either 4366b1 or 4366c0 wireless chips.
Therefore, include firmware for 4366b1 along with 4366c0. This way, all
hardware revisions of the router will be supported by having brcmfmac use
the firmware file for the wireless chip it detects.
Stijn Tintel [Fri, 4 Aug 2023 07:03:10 +0000 (10:03 +0300)]
hostapd: revert upstream commit to fix #13156
Commit e978072baaca ("Do prune_association only after the STA is
authorized") causes issues when an STA roams from one interface to
another interface on the same PHY. The mt7915 driver is not able to
handle this properly. While the commits fixes a DoS, there are other
devices and drivers with the same limitation, so revert to the orginal
behavior for now, until we have a better solution in place.
A hack adjusting fw_devlink value was added to workaround issue with
probing device drivers caused by of_platform_populate(). With upstream
mtd commit (the one adding OF_POPULATED) backported there is no need for
that hack anymore.
Robert Marko [Fri, 11 Aug 2023 21:54:36 +0000 (23:54 +0200)]
ipq40xx: remove DK01 and DK04 boards
DK01 and DK04 board support has been in a form of 2 patches that we have
been carrying for a long time.
Both of the patches contain weird changes, dont follow any DT syntax and I
honestly doubt they are even valid.
DK01 and DK04 also have not been converted to DSA even after a long time
and I doubt that anybody in the community even has these boards as they are
QCA reference boards that are not even obtainable anymore.
Since patches for these 2 boards have been just causing us pain when trying
to update the kernel to a new major release or even point releases lets
remove the support for these boards, and if there are users they can easily
be reinstated.
This update changes the default lockfile directory from /var/lock to
/run [1]. In OpenWRT we still use the "legacy" /var/lock and /run might
not even exist, so we add a patch to revert this particular change.
Martin Schiller [Fri, 4 Aug 2023 10:59:03 +0000 (12:59 +0200)]
linux/named-gpio-export: add support for OPEN_DRAIN and OPEN_SOURCE flag
This change makes it possible to use the GPIO_OPEN_DRAIN /
GPIO_OPEN_SOURCE Flags when exporting GPIOs via dts.
We need to emulate the open-source or open-drain functionalities for the
initial value, because the used functions (gpiod_direction_output_raw)
do not take this into account.
Mathew McBride [Thu, 10 Aug 2023 04:01:20 +0000 (04:01 +0000)]
armsr: armv8: enable AHCI/SATA controllers for mvebu,qoriq,juno
When comparing the generated OpenWrt .config to the Linux arm64
defconfig, I noticed these SATA controllers were not included.
As they may be used as a boot drive, they should be built into
the kernel.
CONFIG_SATA_MVEBU is for Marvell platforms.
CONFIG_SATA_QORIQ is for NXP Layerscape.
CONFIG_SATA_SIL24 is for Arm's Juno development board, see Linux
kernel commit d7c38ff1cd86 ("arm64: defconfig: Add Juno SATA
controller").
Mathew McBride [Tue, 20 Jun 2023 03:30:51 +0000 (03:30 +0000)]
armsr: armv8: enable Broadcom arch'es
This is part of an effort to reduce differences between
the OpenWrt armsr/armv8 config and Linux arm64 defconfig.
This enables CONFIG_ARCH_BCM and downstream
CONFIG_ARCH_BCM2835 (= BCM2711 like Raspberry Pi 4)
and CONFIG_ARCH_BCM_IPROC (Broadcom iProc packet processors).
The broadband specific SoC's (ARCH_BCMBCA) are left out
as it is assumed these will not be doing EFI boot.
Mathew McBride [Wed, 7 Jun 2023 04:39:25 +0000 (04:39 +0000)]
armsr: armv8: fix NXP/Freescale i.MX family configuration
Due to an error on my part, Anton Antonov's
i.MX changes[1] did not fully make it into my
armvirt kernel 6.1 EFI pull request. I have updated
them using the options he supplied[1] as well
as comparing to the Linux arm64 defconfig.
The notable exception is:
CONFIG_USB_DWC3_OF_SIMPLE currently disabled
due to an issue with i.MX8P and i.MX8Q.
Mathew McBride [Mon, 14 Aug 2023 06:31:14 +0000 (06:31 +0000)]
armsr: enable ACPI_BUTTON
A review of the generated OpenWrt kernel .config
vs the Linux arm64 defconfig showed that this
option was not being enabled, as it is disabled
in OpenWrt's generic config.
ACPI_BUTTON is needed to report and respond to
power button events, so it should be enabled.
Mathew McBride [Tue, 20 Jun 2023 01:31:12 +0000 (01:31 +0000)]
armsr: armv8: sync CPU features, EFI, CMA and scheduler options with Linux defconfig
To bring the armsr/armv8 kernel configuration closer to the Linux
arm64 defconfig, synchronize options related to CPU features
(especially more recent Armv8.X variants), scheduler, EFI vars,
CMA and scheduler options.
Mathew McBride [Tue, 15 Aug 2023 03:47:23 +0000 (03:47 +0000)]
kernel: default ARM_PMU on for armsr/armv8
CONFIG_ARM_PMU (Arm Performance Monitor Unit) is a requirement
to use KVM (virtualization) from Linux 5.11+, as the virtualised
guest has virtualized PMU access.
Rosen Penev [Sat, 12 Aug 2023 02:13:41 +0000 (19:13 -0700)]
tools/pkgconf: update to 2.0.1
Changes from 2.0.0 to 2.0.1:
----------------------------
* The behavior of --modversion was largely reverted back to the traditional
pkg-config behavior, but still operates on a solved dependency graph.
The order of --modversion output is based on the dependency resolution
queue which is passed to the solver, which itself generally maps to the
order of the constrants provided on the command line.
* A new flag, --verbose, has been added. When used with `--modversion`, it
is possible to disambiguate which version belongs to which module:
% pkgconf --modversion --verbose foo bar
foo: 1.2.3
bar: 1.3
Changes from 1.9.5 to 2.0.0:
----------------------------
* When flattening the dependency graph, retain the latest seen edges
rather than the earliest.
* Fix a long-standing bug where the dependency resolution queue was
evaluated in reverse. This bug masked the aforementioned dependency
flattening bug in many cases.
* Fix handling of --with-path, which was appending paths to the search
list rather than prepending them as intended.
* Error when --modversion is requested with more than one package, as
the output is ambiguous.
Andre Heider [Sun, 30 Jul 2023 11:24:25 +0000 (13:24 +0200)]
tools: mold: update to 2.1.0
v2.0.0:
- transition from AGPL to MIT
- Previously, mold could not produce an object file with more than 65520
sections using the --relocatable option. Now the bug has been fixed.
- mold now interprets -undefined as a synonym for --undefined instead of
-u ndefined. This seems inconsistent, as -ufoo is generally treated as
-u foo (which is an alias for --undefined foo), but this is the behavior
of the GNU linkers and LLVM lld, so we prioritize compatibility over
consistency.
- -nopie is now handled as a synonym for --no-pie.
- [RISC-V] R_RISCV_SET_ULEB128 and R_RISCV_SUB_ULEB128 relocation types are
now supported (4bffe26, 1ac5fe7)
- [PPC64] R_PPC64_REL32 relocation type is now supported. (ebd780e)
v2.1.0:
- Loongson's LoongArch CPU has been supported. (03b1a1c)
- -z nosectionheader has been added to eliminate section headers from the
output file. (084ca55)
- Previously, linking with the -z pack-relative-relocs option produces an
executable that glibc 2.38 refuses to run with DT_RELR without
GLIBC_ABI_DT_RELR dependency error. Now, mold produces binaries compatible
with glibc 2.38. (f467ad1)
- [ARM64] R_AARCH64_ADR_PREL_PG_HI21_NC relocation type has been supported.
(17a5c3e)
- [ARM64] R_AARCH64_MOVW_UABS_G3 relocation type has now been handled as a
PLT-generating relocation to fix an issue when main is not defined in the
main executable but rather in a .so file. (e764557)
- [RISC-V] We now merge input .riscv.attributes contents. Previously, we
just concatenated them. (aa64491)
Hauke Mehrtens [Sun, 13 Aug 2023 21:02:03 +0000 (23:02 +0200)]
x86: Add virtualization time sync support
This compiles the CONFIG_PTP_1588_CLOCK support into the kernel binary
and activates the drivers for KVM and VMware which allow syncing the
host time with the VM when OpenWrt is running in a VM. With this change
the CONFIG_HYPERV_UTILS driver is now build into the kernel, because it
depends on the PTP framework being compiled in. CONFIG_HYPERV_UTILS was
build as a module, but not packages before.
Hauke Mehrtens [Sun, 13 Aug 2023 20:50:19 +0000 (22:50 +0200)]
x86: Activate CONFIG_PCIEASPM
This activates PCI Express ASPM control in Linux. Without this option it
is completely controlled by the BIOS, now Linux will take over and apply
some workarounds if needed.
Robert Marko [Mon, 14 Aug 2023 11:50:47 +0000 (13:50 +0200)]
ipq40xx: meraki: define DTB load address
It seems that the Meraki bootloader does not respect the kernel ARM booting
specification[1] that requires that address where DTB is located needs to
be 64-bit aligned and often places the DTB on a non 64-bit aligned address
and then kernel fails to find the DTB magic and fails to boot.
Even worse, there is no prints until early printk is enabled and then its
visible that kernel is trying to find the ATAG-s as DTB was not found or
is invalid.
Unifi 6 devices had the same issue and it can be solved by passing the
load adress as part of the FIT image.
It seems that the vendor was aware of the issue and is always relocating
the DTB to 0x89000000, so lets just do the same.
Now that booting is reliable, reenable default images for the Meraki MR33
and MR74 devices.
Reviewed-by: Lech Perczak lech.perczak@gmail.com Signed-off-by: Robert Marko <robimarko@gmail.com>
Hauke Mehrtens [Sun, 13 Aug 2023 20:32:20 +0000 (22:32 +0200)]
linux-firmware: Update Intel AX200 and AX210 firmware
This updates the Intel iwlwifi firmware for AX200 and AX210 from version
66 to version 72. Version 72 is the latest version supported by iwlwifi
from kernel 6.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Sat, 12 Aug 2023 02:06:10 +0000 (19:06 -0700)]
tools/xz: update to 5.4.4
* liblzma and xzdec can now build against WASI SDK when threading
support is disabled. xz and tests don't build yet.
* CMake:
- Fixed a bug preventing other projects from including liblzma
multiple times using find_package().
- Don't create broken symlinks in Cygwin and MSYS2 unless
supported by the environment. This prevented building for the
default MSYS2 environment. The problem was introduced in
xz 5.4.0.
* Documentation:
- Small improvements to man pages.
- Small improvements and typo fixes for liblzma API
documentation.
* Tests:
- Added a new section to INSTALL to describe basic test usage
and address recent questions about building the tests when
cross compiling.
- Small fixes and improvements to the tests.
* Translations:
- Fixed a mistake that caused one of the error messages to not
be translated. This only affected versions 5.4.2 and 5.4.3.
- Updated the Chinese (simplified), Croatian, Esperanto, German,
Korean, Polish, Romanian, Spanish, Swedish, Ukrainian, and
Vietnamese translations.
- Updated the German, Korean, Romanian, and Ukrainian man page
translations.
Daniel Golle [Wed, 9 Aug 2023 11:21:41 +0000 (12:21 +0100)]
uboot-mediatek: bpi-r3: prepare for larger FIT structures
Instead of reading only a single 4kiB page, read the first 128kiB to
determine the size of an uImage.FIT using 'imsz' or 'imszb'.
This will be needed once we add more Device Tree Overlays, which may
happen for the BPi-R3 mini.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 4 Aug 2023 13:07:43 +0000 (14:07 +0100)]
mediatek: filogic: mt7988: mark RTC clock as critical
A dependency of the MT7988 MMC host controller on the SoC's RTC clock
being running has been discovered. Mark RTC clock as critical to fix
MMC host on MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Zoltan HERPAI [Sun, 17 Jan 2021 22:26:33 +0000 (23:26 +0100)]
sunxi: add modules for AC100 MFD and RTC
The X-Powers AC100 is a multi-function IC used to provide RTC
and audio codec via RSB (reduced serial bus, an Allwinner-
speciality). On some boards using the A80/A83T SoCs, aside
from the RTC functionality, the RTC is used as a clocksource
for the Ampak WiFi/BT modules.
build: Add option KERNEL_KASAN_SW_TAGS and HW_TAGS
Currently KASAN is supported but only the generic one. SW-tag and HW-tag
based KASAN have less impact on memory footprint or performance, and are
worth supporting.
Add choice menu for software and hardware Tag-Based KASAN, in addition
to the generic one.
Felix Fietkau [Thu, 10 Aug 2023 16:33:04 +0000 (18:33 +0200)]
hostapd: reimplement AP/STA support via ucode
Drop obsolete control interface patches.
This fixes some corner cases in the previous code where the segment 0 center
frequency was not adjusted properly, leading to logspam and non-working AP
interfaces.
Additionally, shutting down the AP was broken, because the next beacon update
would re-enable it, leading to a race condition on assoc.
Linus Walleij [Mon, 7 Aug 2023 21:58:24 +0000 (23:58 +0200)]
gemini: Fix up kernel v6.1 config
The v6.1 kernel has moved around the options for the RTL8366RB
DSA switch used in the DIR-685 so it was missing when building
the kernel. Fix it up by adding the right Kconfig options.
Robert Marko [Wed, 9 Aug 2023 16:29:00 +0000 (18:29 +0200)]
qualcommax: remove upstreamed TRIM quirks
TRIM disable quirks for eMMC-s were merged upstreamed and backported to
stable in 6.1.39, however they were not dropped during the kernel update
and quilt is not complaining at all.
So, lets manually remove them as they are part of 6.1.39 [1] [2].
1. Needed to make a change to to package/kernel/linux/modules/netsupport.mk
due to upstream moving vxlan to its own directory[1]. @john-tho suggested
using the the 6.1 xvlan FILES to circumvent.
2. All patches automatically rebased.
Ivan Pavlov [Fri, 4 Aug 2023 12:28:12 +0000 (15:28 +0300)]
openssl: update to 3.0.10
Changes between 3.0.9 and 3.0.10 [1 Aug 2023]
* Fix excessive time spent checking DH q parameter value ([CVE-2023-3817])
* Fix DH_check() excessive time with over sized modulus ([CVE-2023-3446])
* Do not ignore empty associated data entries with AES-SIV ([CVE-2023-2975])
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
xdp-tools: disable stack protector for BPF programs
When building xdp-tools with CONFIG_USE_LLVM_HOST=y, on a host that
enabled stack protector by default in Clang, compilation fails with the
following error:
CLANG xdp-dispatcher.o
clang-16: error: ignoring '-fstack-protector-strong' option as it is not currently supported for target 'bpfeb' [-Werror,-Woption-ignored]
Add -fno-stack-protector to BPF_CFLAGS to fix this.
projects / thirdparty / openwrt.git / log
