Shiji Yang [Sat, 23 Sep 2023 01:25:15 +0000 (09:25 +0800)]
mac80211: rt2x00: fix MT7620 low RSSI issue
Introducing SoC specific RSSI base value to fix the low RSSI issue
on MT7620. With this fix[1], the RSSI value reported by MT7620 will
increase by 10 dB.
Daniel Golle [Tue, 12 Sep 2023 23:57:49 +0000 (00:57 +0100)]
mediatek: add build for MT7981 RFB
Add build for the MTK3943 reference board for MT7981B+MT7976C.
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: various options
- RAM: 256MB DDR3
- Ethernet: 4 x 10/100/1000 Mbps via MT7531AE switch
EITHER 1 x 10/100/1000 Mbps built-in PHY
OR 1 x 10/100/1000/2500 Mbps MaxLinear GPY211C
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: RST, WPS
**Flash instructions for SPIM-NAND:**
- write *mt7981-rfb-spim-nand-preloader.bin to 'BL2' partition
- write *mt7981-rfb-spim-nand-bl31-uboot.fip to 'FIP' partition
- erase 'ubi' partition
- reset board
- create ubootenv and ubootenv2 UBI volumes in U-Boot
- edit environment and set bootcmd, e.g.
setenv bootconf 'config-1#mt7981-rfb-spim-nand#mt7981-rfb-mxl-2p5g-phy-eth1'
setenv bootcmd 'ubi read $loadaddr fit; bootm $loadaddr#$bootconf'
- load initramfs image via TFTP:
setenv serverip 192.168.1.254
setenv ipaddr 192.168.1.1
setenv bootfile openwrt-mediatek-filogic-mediatek_mt7981-rfb-initramfs.itb
saveenv ; saveenv
tftpboot
bootm $loadaddr#$bootconf
- Now use sysupgrade to write OpenWrt firmware to flash.
SNFI-NAND, SPIM-NOR and eMMC all work very similar, a bootable SD card image
is also being generated. However, as the board I've been provided only comes
with SPIM-NAND all other boot media are untested.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 18 Sep 2023 15:40:30 +0000 (16:40 +0100)]
arm-trusted-firmware-mediatek: fix copy&paste error in Makefile
When adding builds for MT7981 the related Makefile sections for MT7986
have apparently been copied, but in one instance the rename from 7986 to
7981 has been omitted. Fix that now.
Fixes: 602cb4f325 ("arm-trusted-firmware-mediatek: add build for MT7981 DDR3") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 11 Sep 2023 21:49:59 +0000 (22:49 +0100)]
kernel: serial: 8250_mtk: track busclk state to avoid bus error
UARTs not used as boot console are currently broken on some MediaTek
targets due to register access depending on the bus clock being enabled.
Add patch to make sure this dependency is always met.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Andreas Böhler [Sat, 9 Sep 2023 20:54:01 +0000 (22:54 +0200)]
ipq4019: add support for ZTE MF282 Plus aka DreiTube
The ZTE MF282 Plus is a LTE router used (exclusively?) by the network
operator "3". It is very similar to the MF286/MF287 but in the form factor
of the MF282.
LAN: from config
WiFi 1: from config + 1
WiFi 2: from config + 2
Installation
============
Option 1 - TFTP
---------------
TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:
Option 2 - From stock firmware
------------------------------
The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.
The exploit will be available at the device wiki page.
Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".
ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd9 is the partition labelled "rootfs" by calling
"cat /proc/mtd".
Option 2 - from within OpenWrt
------------------------------
This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.
Follow the commands from Option 1 to flash back to stock.
LTE Modem
=========
The LTE modem is similar to the MF286R, it provides an RNDIS interface
and an AT interface.
Other Notes
===========
There is one GPIO Switch "Power button blocker" which, if enabled, does not
trigger a reset of the SoC if the modem reboots. If disabled, the SoC is
rebooted along with the modem. The modem can be rebooted via the exported
GPIO "modem-reset" in /sys/class/gpio.
Robert Marko [Thu, 3 Aug 2023 11:16:05 +0000 (13:16 +0200)]
mvebu: eDPU: add support for version with external switch
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.
The same image can be used on both versions as U-Boot will enable the
switch node and disable the unused ethernet controller.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Robert Marko [Fri, 18 Aug 2023 10:22:29 +0000 (12:22 +0200)]
uboot-mvebu: eDPU: add support for version with external switch
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.
In order to use the same image for both boards, U-Boot is responsible for
detecting the revision and enabling/disabling DTS nodes.
So, to make it easy for users, lets add the pending U-Boot patches to build
in OpenWrt.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Robert Marko [Thu, 14 Sep 2023 10:44:02 +0000 (12:44 +0200)]
generic: 5.15: backport support for Marvell 88E6361 switch
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.
Since 5.15 doesnt have phylink_get_caps I had to modify the backport to
use the old mv88e6393x_phylink_validate instead.
I had to fixup one more instance of port_max_speed_mode as well that is not
present in 6.5.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Andreas Böhler [Mon, 18 Sep 2023 10:08:18 +0000 (12:08 +0200)]
ipq40xx: ZTE MF287 series: move to gpio-export for modem-reset GPIO
Turn the "gpio-restart" node into a "gpio-export" node for all MF287
variants, similar to the MF287 Pro. Unfortunately, there doesn't seem to be
a "power button blocker" GPIO for the MF287 and MF287 Plus, so a modem
reset always triggers a system reset.
Andreas Böhler [Sat, 16 Sep 2023 19:55:01 +0000 (21:55 +0200)]
ipq40xx: refactor ZTE MF287 series
The ZTE MF287 requires a different board calibration file for ath10k than
the ZTE MF287+. The two devices receive their own DTS, thus the device tree
is slightly refactored.
Pascal Coudurier [Wed, 23 Aug 2023 20:45:31 +0000 (22:45 +0200)]
kernel: modules: video: adapt drm-amdgpu and drm-radeon for kernel 6.1
Package and add dependencies to drm-amdgpu and drm-radeon for 6.1
* package acpi-video, drm-display-helper and drm-buddy
* add acpi-video, drm-display-helper and drm-buddy as dependencies for
drm-amdgpu
* add acpi-video and drm-display-helper as dependencies for drm-radeon
Andreas Böhler [Tue, 12 Sep 2023 17:57:55 +0000 (19:57 +0200)]
ipq40xx: fix image building for ZTE MF287 series
For the ZTE MF287 series, a special recovery image is built. The Makefile
worked fine on snapshot, but created corrupt images on the 23.05 images.
By using the appropriate variable, this should be fixed.
Max Qian [Fri, 15 Sep 2023 04:54:30 +0000 (21:54 -0700)]
ramips: RT1800: fix invalid octal number error
This commit removes the padded zeros in the date formatting.
The padded zeros from the date command causes the numbers
to be interpreted as an octal number by printf. Months, days,
and years with the number 08 or 09 raise an error in printf as an
"invalid octal number" and get interpreted as a zero.
Robert Marko [Mon, 14 Aug 2023 10:56:49 +0000 (12:56 +0200)]
ipq40xx: move DSA and ethernet driver to 5.15 specific directory
As a preparation to move to 6.1, we need to move the DSA and ethernet
drivers to a 5.15 specific directory as 6.1 will use the latest patchset
that was sent upstream which is too hard to backport to 5.15.
On some WLR-7100 routers, significant packet loss was observed. This is
fixed by configuring a delay on the GMAC0 RXD and RXDV lines.
The values used in this commit are copied from the values used by the
stock firmare (based on register dumping).
Out of four test routers, the problem was consistently observed on two.
It is unclear what the relevant difference is exactly (the two working
routers were v1 001 with AR1022 and v1 002 with AR9342, the two broken
routers were both v1 002 with AR1022). All PCB routing also seems
identical, so maybe there is some stray capacitance on some of these
that adds just enough delay or so...
With this change, the packet loss disappears on the broken routers,
without introducing new packet loss on the previously working routers.
Note that the PHY *also* has delays enabled (through
`qca,ar8327-initvals`) on both RX and TX lines, but apparently that is
not enough, or it is not effective (registers have been verified to be
written).
For detailed discussion of this issue and debug history, see
https://forum.openwrt.org/t/sitecom-wlr-7100-development-progress/79641
Robert Marko [Sat, 16 Sep 2023 09:26:35 +0000 (11:26 +0200)]
mac80211: ath11k: drop upstreamed patches
Commit ed3725e15a154ebebf44e0c34806c57525483f92
("wifi: ath11k: Fix qmi_msg_handler data structure initialization")
has been present upstream since 6.1.2 but it seems Quilt refreshed it
wrongly so it appeared like a completely different patch.
Commit 7c15430822e71e90203d87e6d0cfe83fa058b0dc
("wifi: ath11k: allow system suspend to survive ath11k")
has been present upstream since 6.1.16 but somehow quilt still happily
applied it.
Erik Karlsson [Wed, 6 Sep 2023 10:33:17 +0000 (12:33 +0200)]
procd: create /dev/fd symlink
This is needed for ksh/bash style process substitution such as
<(command) and >(command) which was introduced in ash as of busybox
version 1.34.0 to work.
Signed-off-by: Erik Karlsson <erik.karlsson@genexis.eu>
ath79: add support for MikroTik RouterBOARD 750 r2 (hEX lite)
This patch adds support for the MikroTik RouterBOARD 750 r2, marketed as
hEX lite, a small indoor router with 5x 10/100 Mbps Ethernet ports, one
with PoE in. The device was already supported by the ar71xx target.
See https://mikrotik.com/product/RB750r2 for more details.
Not working:
- Serial port (already not working in ar71xx)
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Only the
"Internet" port will ask for an initramfs image. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Hannu Nyman [Wed, 13 Sep 2023 13:49:03 +0000 (16:49 +0300)]
scripts/download.pl: Remove stale download sites and convert to https
Remove the stale site definitions from @APACHE, KERNEL etc.
* Remove site that had dropped APACHE
* Remove KERNEL site leading to wrong directory
* Remove dead sites
* Convert ftp/http URLs to https, if possible. Remove duplicate
Thomas Makin [Tue, 5 Sep 2023 00:00:14 +0000 (20:00 -0400)]
ipq40xx: add support for Netgear RBX40
This adds support for the RBR40 and RBS40 (sold together as RBK40),
two netgear routers identical to SRR60/SRS60 in all but antennae (and
hardware id). See 2cb24b3f3c for details.
Signed-off-by: Thomas Makin <halorocker89@gmail.com>
Felix Fietkau [Thu, 14 Sep 2023 17:08:34 +0000 (19:08 +0200)]
hostapd: fix more AP+STA issues
When STA is disconnected, ensure that the interface is in a cleanly stopped
state:
- if in regular enable/disable state, stop beacons if necessary
- in any other state, disable the interface
When the STA is up, ignore repeated start commands for the same channel, in
order to avoid unnecessary AP restarts
Felix Fietkau [Wed, 13 Sep 2023 09:00:53 +0000 (11:00 +0200)]
hostapd: update to the latest version
8e6485a1bcb0 PEAP client: Update Phase 2 authentication requirements de9a11f4dde9 TTLS client: Support phase2_auth=2 b2a1e7fe7ab9 tests: PEAP and TTLS phase2_auth behavior 518ae8c7cca8 P2P: Do not print control characters in debug a4c133ea73c7 WPS: Optimize attribute parsing workaround 7a37a94eaa0d Check whether element parsing has failed f80d83368818 ACS: Remove invalid debug print fb2b7858a728 FILS: Fix HE MCS field initialization 50ee26fc7044 P2P: Check p2p_channel_select() return value a50d1ea6a2b3 Add QCA vendor attributes for user defined power save parameters 4636476b7f22 Set RRM used config if the (Re)Association Request frame has RRM IE e53d44ac63e8 AP MLD: Use STA assoc link address in external auth status to the driver 99a96b2f9df7 AP MLD: OWE when SME is offloaded to the driver 96deacf5d710 nl80211: Skip STA MLO link channel switch handling in AP mode d320692d918a AP MLD: Handle new STA event when using SME offload to the driver faee8b99e928 tests: Fix eht_mld_sae_legacy_client to restore sae_pwe c3f465c56c94 wlantest: Handle variable length MIC field in EAPOL-Key with OWE 605034240e0c wlantest: Support multiple input files 053bd8af8ed2 Recognize FTE MLO subelements 43b5f11d969a Defragmentation of FTE 3973300b8ded FTE protected element check for MLO Reassociation Response frame 74e4a0a6f1e4 wlantest: Learn AP MLD MAC address from Beacon frames a5a0b2cf7b1b wlantest: Find non-AP MLD only from affiliated BSSs of the AP MLD 74472758584d wlantest: Recognize non-AP MLD based on any link address for decryption 1ffabd697c67 wlantest: Learn non-AP MLD MAC address from (Re)Association Request frames 4e8e515f92b9 wlantest: Use MLO search for the STA in reassociation 49bf9f2df95a wlantest: Use the MLD MAC address as well for matching STA entries 5434a42ec69c wlantest: Search for FT Target AP using MLD MAC address as well a19fcf685cae wlantest: Include the MLD MAC address of the AP MLD in new-STA prints 709d46da73da wlantest: Do not claim update to AP MD MAC address if no change 770760454f9e wlantest: Do not update BSS entries for other AP MLDs in PTK cloning 084745ffc508 Add QCA vendor attributes for NDP setup bf9cbb462fd9 Fix writing of BIGTK in FT protocol 011775af9443 tests: Check for beacon loss when using beacon protection 8f148d51322f Fix a compiler warning on prototype mismatch b7db495ad9c9 AP: Fix ieee802_1x_ml_set_sta_authorized() 232667eafe0d Fix CCMP test vector issues 30771e6e05ed Include PTID in PV1 nonce construction for CCMP test vector 34841cfd9aba Minor formatting changes to CCMP test vectors a685d84139e6 BSS coloring: Fix CCA with multiple BSS bc0636841a70 wpa_supplicant: Fix configuration parsing error for tx_queue_* 2763d1d97e66 hostapd: Fix AID assignment in multiple BSSID 763a19286e2f AP: Add configuration option to specify the desired MLD address bd209633eb10 AP: Use is_zero_ether_addr() to check if BSSID is NULL bc0268d053b4 wlantest: Guess SAE/OWE group from EAPOL-Key length mismatch a94ba5322803 EHT: Support puncturing for 320 MHz channel bandwidth 7e1f5c44c97e EHT: 320 MHz DFS support 6f293b32112a QCA vendor attributes for updating roaming AP BSSID info 5856373554eb Extend QCA vendor command to include more parameters for netdev events e080930aa0a5 Define QCA vendor roam control RSSI attributes fe72afe713ad Define QCA vendor attribute for high RSSI roam trigger threshold 47a65ccbfde2 P2P: Clean wpa_s->last_ssid when removing a temporary group network 884125ab7d21 tests: P2P autonomous GO and clearing of networking information 7637d0f25053 P2P: Do not filter pref_freq_list if the driver does not provide one dd1330b502ff Fix hostapd interface cleanup with multiple interfaces 0a6842d5030e nl80211: Fix beacon rate configuration for legacy rates 36, 48, 54 Mbps d606efe054d5 tests: Beacon rate configuration for 54 Mbps f91d10c0e6aa tests: Update RSA 3k certificates 07d3c1177bbb tests: Make sae_proto_hostapd_status_* more robust 1085e3bdc6f6 Update iface->current_mode when fetching new hw_features 338a78846b44 Add a QCA vendor sub command for transmit latency statistics 9318db7c38bc wlantest: Use local variables for AA/SPA in FT Request/Response processing 628b9f10223d wlantest: Derive PMK-R1 and PTK using AA/SPA for MLO FT over-the-DS 104aa291e5c8 wlantest: Fix FT over-the-DS decryption 37c87efecfe3 wlantest: Search SPA using MLO aware find for FT Request/Response frame 19f33d7929e8 wlantest: Learn the Link ID for AP MLD affiliated BSSs 6ae43bb10323 wlantest: Learn link address for assoc link from (Re)Association Request 4c079dcc64da Increment hmac_sha*_vector() maximum num_elem value to 25 e6f64a8e1daf FT: FTE MIC calculation for MLO Reassociation Request frame a83575df5994 wlantest: FTE MIC calculation for MLO Reassociation Request frames ff02f734baf8 wlantest: Allow specific link BSS to be found with bss_find_mld() 7381c60db8f0 FT: Make FTE MIC calculation more flexible ac9bf1cc2a4c Decrement hmac_sha*_vector() maximum num_elem value to 11 aa08d9d76803 Fix use of defragmented FTE information 78b153f90a74 Calculate defragmented FTE length during IE parsing 8cf919ffd5c4 wlantest: FTE MIC calculation for MLO Reassociation Response frame d12a3dce82a9 wlantest: Store and check SNonce/ANonce for FT Authentication 20febfd7838d wlantest: Dump MLO association information in debug 609864d6a8a1 Add QCA vendor attribute to configure MLD ID in ML probe request 12154861e24a Add support for conversion to little endian for 24 bits c437665041c0 Add Non EHT SCS Capability in (Re)Association Request frames 33da386553b7 SCS: Add support for QoS Characteristics in SCS request edfca280cbe8 SCS: Add support for optional QoS Charateristics parameters 32dcec9529ec Send actual MFP configuration when driver takes care of BSS selection 123d16d860fa Update hw_mode when CSA finishes b3d852560bda Change QCA vendor configure attribution name of peer MAC address 12fabc4765c2 Add QCA vendor attribute for configuring max A-MPDU aggregation count f6eaa7b729cb Add QCA vendor attribute for TTLM negotiation support type f6dcd326fea7 wlantest: Indicate ToDS/FromDS values for BSS DATA entries 6ce745bb87d4 wlantest: MLO support for decrypting 4-address frames 850dc1482953 wlantest: Remove duplicated A1/A2/A3 override detection for MLO 770e5a808fbb wlantest: Determine whether A1 points to STA once in rx_data_bss_prot() 377d617b574a Define new BSS command info mask for AP MLD address d3ab6e001f62 wlantest: Use non-AP MLD's MLD MAC address in FT over-the-air derivation a845601ffe32 wlantest: Derive PTK in MLO using MLD MAC addresses for FT over-the-air 0cd2bfc8a402 wlantest: Fix FTE MIC calculation for MLO Reassociation Response frames 528abdeb673b wlantest: Learn group keys from MLO FT Reassociation Response frames 990600753dd9 wlantest: Defragment Basic MLE before processing de043ec01ab5 wlantest: Defragment the Per-STA Profile subelement bae1ec693c44 wlantest: Minimal parsing of Basic MLE STA Profile ba1579f3bf7c Clear BIGTK values from wpa_supplicant state machine when not needed b46c4b9a916a tests: Beacon protection and reconnection 3e71516936b7 Document per-ESS MAC address (mac_addr=3 and mac_value) f85b2b2dee3b Extend wpa_parse_kde_ies() to include EHT capabilities e3a68081bc1e driver: Add option for link ID to be specified for send_tdls_mgmt() c7561502f2e8 nl80211: Use a QCA vendor command to set the link for TDLS Discovery Response a41c8dbdd84e TDLS: Copy peer's EHT capabilities 626501434be1 TDLS: Learn MLD link ID from TDLS Discovery Response 5f30f62eead7 TDLS: Reply to Discovery Request on the link with matching BSSID 940ef9a05c0f TDLS: Use link-specific BSSID instead of sm->bssid for MLO cases f429064189c3 TDLS: Set EHT/MLO information for TDLS STA into the driver dd25885a9daa Remove space-before-tab in QCA vendor related definitions af6e0306b2a9 Fix typos in QCA vendor related definitions 4c9af238c1e4 Fix inconsistent whitespace use in QCA vendor related definitions e5ccbfc69ecf Split long comment lines in QCA vendor related definitions
Felix Fietkau [Sat, 9 Sep 2023 15:07:09 +0000 (17:07 +0200)]
hostapd: rework reload support and MAC address handling
MAC address and interface name assigned by mac80211.sh depend on the order in
which interfaces are brought up. This order changes when interfaces get added
or removed, which can cause unnecessary reload churn.
One part of the fix it making MAC address allocation more dynamic in both
wpa_supplicant and hostapd, by ignoring the provided MAC address using
the next available one, whenever the config does not explicitly specify one.
The other part is making use of support for renaming netdevs at runtime and
preserving the MAC address for renamed netdevs.
Aviana Cruz [Mon, 20 Jun 2022 13:55:45 +0000 (21:55 +0800)]
ramips: add support for mtk eip93 crypto engine
Mediatek EIP93 Crypto engine is a crypto accelerator which
is available in the Mediatek MT7621 SoC.
Signed-off-by: Aviana Cruz <gwencroft@proton.me> Co-authored-by: Richard van Schagen <vschagen@icloud.com> Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn>
Hannu Nyman [Fri, 8 Sep 2023 16:47:01 +0000 (19:47 +0300)]
base-files: sysupgrade: Add 2 sec sleep into process KILL loop
Add 2 seconds sleep after each forcibly killed/tried-to-kill process
in the final process termination loop in sysupgrade stage2.
This is needed especially for qualcommax/ipq807x, where ath11k
wireless driver may have a long 10-20 seconds delay after termination
before actually getting killed. This often breaks sysupgrade.
The current KILL loop in kill_remaining does all 10 kill attempts
consecutively without any delay, as evidenced here in a failing sysupgrade.
It does not allow any time for the process to finalize its internal
termination.
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending TERM to remaining processes ...
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending signal TERM to hostapd (2122)
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending signal TERM to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending KILL to remaining processes ...
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2122)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Failed to kill all processes.
sysupgrade aborted with return code: 256
The change in this commit adds a 2 seconds delay after each kill attempt
in order to allow some processes to more gracefully handle their
internal termination.
The result is like this:
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending TERM to remaining processes ...
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending signal TERM to hostapd (2309)
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending signal TERM to hostapd (2324)
Sun Sep 3 11:15:14 EEST 2023 upgrade: Sending KILL to remaining processes ...
Sun Sep 3 11:15:14 EEST 2023 upgrade: Sending signal KILL to hostapd (2309)
[ 699.827521] br-lan: port 7(hn5wpa2r) entered disabled state
[ 699.908673] device hn5wpa2r left promiscuous mode
[ 699.908721] br-lan: port 7(hn5wpa2r) entered disabled state
[ 701.038029] br-lan: port 6(hn5wpa3) entered disabled state
Sun Sep 3 11:15:16 EEST 2023 upgrade: Sending signal KILL to hostapd (2324)
[ 702.058256] br-lan: port 5(hn2wlan) entered disabled state
[ 709.250063] stage2 (8237): drop_caches: 3
Sun Sep 3 11:15:25 EEST 2023 upgrade: Switching to ramdisk...
The delay introduced here only kicks in if there is some process that
does not get terminated by the first TERM call. Then there is at least
one 2 sec wait after the first KILL loop round.
This commit is related to discussion in PRs #12235 and #12632
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> Reviewed-by: Robert Marko <robimarko@gmail.com>
Jonas Gorski [Sat, 9 Sep 2023 10:44:42 +0000 (12:44 +0200)]
x86: geode: fix hwrng register accesses
When the membase and pci_dev pointer were moved to a new struct in priv,
the actual membase users were left untouched, and they started reading
out arbitrary memory behind the struct instead of registers. This
unfortunately turned the RNG into a constant number generator, depending
on the content of what was at that offset.
To fix this, update geode_rng_data_{read,present}() to also get the
membase via amd_geode_priv, and properly read from the right addresses
again.
Closes #13417.
Reported-by: Timur I. Davletshin <timur.davletshin@gmail.com> Tested-by: Timur I. Davletshin <timur.davletshin@gmail.com> Suggested-by: Jo-Philipp Wich <jo@mein.io> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Daniel Golle [Mon, 11 Sep 2023 11:50:38 +0000 (12:50 +0100)]
kernel: backport two fixes for MediaTek Ethernet driver
Fix PSE port assignment for 3rd GMAC on MT7988 and make sure dma_addr
is always initialized to prevent potentially accessing uninitialized
stack memory in the error path.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
projects / thirdparty / openwrt.git / log
