Explain some of the more obscure logic, or where we deviate from
what the original awk code did. Also, give a count of the usable
addresses on the subnet.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
base-files: ipcalc.sh: Add support for decimal output
This is useful if you later need to perform numeric range-checking
on addresses, i.e. to see if an address falls inside a CIDR range,
etc. and what interface it corresponds to.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Pawel Dembicki [Fri, 8 Dec 2023 08:32:41 +0000 (09:32 +0100)]
kirkwood: fix Ctera C200 V1 ubi part name
In 749237967a12 downstream dts was replaced with upstream accepted
patch. But in upstream version last partition was called "rootfs"
instead "ubi". OpenWrt require "ubi" label for ubi rootfs.
This patch restore proper label.
The kernel patches apply with only minor changes. The only other notable
change is that octeon-usb has moved from staging and had its config
macro renamed from CONFIG_OCTEON_USB to CONFIG_USB_OCTEON_HCD.
Daniel Golle [Fri, 17 Nov 2023 02:25:09 +0000 (02:25 +0000)]
mediatek: add support for Adtran SmartRG Bonanza Peak series
The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s
Wi-Fi 6 residential gateway, access point and mesh router products.
All of them come with an eMMC to boot from, are powered via USB-C and
got a USB 3.0 type-A port. All of them got a Dialog (Renesas) DA14531
Bluetooth module connected via UART. If the device was previously
running stock firmware, the BT chip's internal flash has been loaded
with firmware and it can be attached using hciattach when using
OpenWrt.
* SDG-8612 - Dual-band RJ-45 gateway
2x 2.5G MaxLinear PHY for WAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8614 - Dual-band SFP gateway
1x SFP cage with up to 2.5G speed
1x 2.5G MaxLinear PHY for LAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8622 - Tri-band mesh router
2x 2.5G MaxLinear PHY
The MT7986 2G and 5G are used as 2G and 5G high band.
There’s a MT7915 PCIe card for 5G low band.
* SDG-8632 - Tri-band mesh router with 6 GHz
2x 2.5G MaxLinear PHY
The MT7986 serves the 2G and 6G bands.
There’s a MT7915 PCIe card for 5G.
Installation via U-Boot serial console:
0. setup TFTP server with IP 192.168.1.10/24, place initramfs image
renamed to openwrt.XXX where XXX is the internal product number:
SDG-8612: XXX = 412
SDG-8614: XXX = 414
SDG-8622: XXX = 422
SDG-8632: XXX = 432
1. connect to the serial console and power on the device.
Interrupt the bootloader by pressing 'st'
2. setenv boot_mode openwrt ; saveenv
3. run boot1
Load firmware via TFTP and write to flash
4. run boot2
Now OpenWrt initramfs should boot
5. upload sysupgrade.bin via scp to /tmp
6. sysupgrade
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 10 Dec 2023 01:15:36 +0000 (01:15 +0000)]
kernel: hack: support inverted LEDs on MaxLinear GPY211 PHY
Add downstream DT property to setup the PHY LEDs of the MaxLinear
GPY211 PHY in such way that the VDD of the LED is driven by the SoC
pin rather than the GND (which is the default).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 17 Nov 2023 00:02:05 +0000 (00:02 +0000)]
base-files: add mmc_get_mac_ascii function
Similar to the *_get_mac_binary function, also split the common parts
off mtd_get_mac_ascii into new get_mac_ascii function and introduce
mmc_get_mac_ascii which uses it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add Generic subtarget definition. This is needed to keep consistent name
on every other target/subtarget and also to permit correct work of CI
workflows that expect a target/subtarget pattern.
Fixes: c16b2293fe71 ("ixp4xx: Resurrect IXP4xx support using device tree") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Kamil Jońca [Sun, 5 Nov 2023 13:49:01 +0000 (14:49 +0100)]
ramips: add TP-LINK TL-WR902AC v4
Seems to be very similar to: https://openwrt.org/toh/tp-link/tl-wr902ac_v3
1 x usb
1 x eth
Powered by mini usb port.
Installation:
Can use TFTP method to install:
1. establish TFTP server at 192.168.0.66
2. provide tp_recover.bin file to the TFTP server
3. turn on router with reset button pressed
4. wait for led blinking, then release reset
Specification based on dmesg from already flashed device:
SoC Type: MediaTek MT7628AN ver:1 eco:2
CPU0 revision is: 00019655 (MIPS 24KEc)
Memory: 56028K/65536K available
CPU Clock: 580MHz
WiFi: MT7613BE
MAC addresses are all the same, except wifi5g which last part is decrement by one, ie.:
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (superadmin:xxxxxxxxxx, where
xxxxxxxxxx is a new password from the p.5)
9. Enable SSH access to the router (Settings -> Access control -> SSH)
10. Connect to the router using SSH shell using superadmin account
11. Run in SSH shell:
sh
12. Make a mtd backup (optional, see related section)
13. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
14. Login to the router web interface under admin account
15. Remove dots from the OpenWrt factory image filename
16. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.0.2
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | f4:*:66 |
| WAN | label + 11 | f4:*:71 |
| 2g | label + 2 | f4:*:68 |
| 5g | label + 3 | f4:*:69 |
+-----+------------+---------+
The label MAC address was found in Factory, 0x21000
Florian Eckert [Mon, 7 Aug 2023 09:15:28 +0000 (11:15 +0200)]
tools: add tmon package
Add the 'tmon' packages. This is as a tool to help visualize,
tune, and test the complex thermal subsystem.
We get a compile warning for the tool that the printf format does not
fit. This commit contains a patch that fixes this warning. This patch
has also been sent upstream to the Linux kernel [1].
Felix Fietkau [Tue, 5 Dec 2023 11:59:49 +0000 (12:59 +0100)]
libnl-tiny: update to Git HEAD (2023-12-05)
af57bb123f93 socket: add debug callbacks for rx/tx 785e11aee7dd socket: call rx debug callback once per packet instead of per batch 965c4bf49658 socket: change debug callbacks to pass struct nl_msg
Rafał Miłecki [Mon, 20 Nov 2023 10:46:26 +0000 (11:46 +0100)]
mediatek: filogic: add Acelink EW-7886CAX support
Acelink EW-7886CAX is an MT7986A (AKA Filogic 830) based access point.
It has 512 MiB of RAM, one 2.5 Gbps PoE (802.3at) Ethernet port and
on-SoC Wi-Fi. There is no printed MAC label (on my unit).
My unit came with Mediatek's firmware (based on OpenWrt 21.02)
installed. It was possible to simply upgrade using OpenWrt's sysupgrade
tool.
Another verified upgrade method is using U-Boot (requires UART). During
every boot there is "U-Boot Boot Menu". Selecting option "2. Upgrade
firmware" allows using U-Boot's tftp client to load and flash factory
image.
David Bauer [Mon, 4 Dec 2023 12:54:56 +0000 (13:54 +0100)]
mpc85xx: allow mapping of cpu1 spin-table page
The no-map property was incorrectly added, which kept the system-memory
available on the WS-AP3825 limited to 190MB. We are allowed to map the
page containing the CPU1 spin-table, we are just not allowed to write to
it.
Fixes: 57d7382cb159 ("mpc85xx: increase available RAM on Extreme Networks WS-AP3825i") Signed-off-by: David Bauer <mail@david-bauer.net>
Nick Hainke [Sat, 11 Nov 2023 07:54:17 +0000 (08:54 +0100)]
tools/xz: update to 5.4.5
* liblzma:
- Use __attribute__((__no_sanitize_address__)) to avoid address
sanitization with CRC64 CLMUL. It uses 16-byte-aligned reads
which can extend past the bounds of the input buffer and
inherently trigger address sanitization errors. This isn't
a bug.
- Fixed an assertion failure that could be triggered by a large
unpadded_size argument. It was verified that there was no
other bug than the assertion failure.
- Fixed a bug that prevented building with Windows Vista
threading when __attribute__((__constructor__)) is not
supported.
* xz now properly handles special files such as "con" or "nul" on
Windows. Before this fix, the following wrote "foo" to the
console and deleted the input file "con_xz":
echo foo | xz > con_xz
xz --suffix=_xz --decompress con_xz
* Build systems:
- Allow builds with Windows win95 threading and small mode when
__attribute__((__constructor__)) is supported.
- Added a new line to liblzma.pc for MSYS2 (Windows):
Cflags.private: -DLZMA_API_STATIC
When compiling code that will link against static liblzma,
the LZMA_API_STATIC macro needs to be defined on Windows.
- CMake specific changes:
* Fixed a bug that allowed CLOCK_MONOTONIC to be used even
if the check for it failed.
* Fixed a bug where configuring CMake multiple times
resulted in HAVE_CLOCK_GETTIME and HAVE_CLOCK_MONOTONIC
not being set.
* Fixed the build with MinGW-w64-based Clang/LLVM 17.
llvm-windres now has more accurate GNU windres emulation
so the GNU windres workaround from 5.4.1 is needed with
llvm-windres version 17 too.
* The import library on Windows is now properly named
"liblzma.dll.a" instead of "libliblzma.dll.a"
* Fixed a bug causing the Ninja Generator to fail on
UNIX-like systems. This bug was introduced in 5.4.0.
* Added a new option to disable CLMUL CRC64.
* A module-definition (.def) file is now created when
building liblzma.dll with MinGW-w64.
* The pkg-config liblzma.pc file is now installed on all
builds except when using MSVC on Windows.
* Added large file support by default for platforms that
need it to handle files larger than 2 GiB. This includes
MinGW-w64, even 64-bit builds.
* Small fixes and improvements to the tests.
* Updated translations: Chinese (simplified) and Esperanto.
David Bauer [Sun, 3 Dec 2023 05:49:40 +0000 (06:49 +0100)]
uboot-envtools: fix GL-MT2500 offset
The previous offsets did also work, as they've wrapped back to 0x0.
However, in reality the environment starts at offset 0x0 of the
u-boot-env MMC partition.
Marty Jones [Tue, 28 Nov 2023 18:27:18 +0000 (13:27 -0500)]
kernel: backport fixes for realtek r8152
Fixes issues with RTL8156 2.5G USB adapters
- # ethtool eth1
Settings for eth1:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 2500Mb/s
Duplex: Half
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
MDI-X: Unknown
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
- #
- r8152: break the loop when the budget is exhausted
- r8152: Block future register access if register access fails
- r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE
- r8152: add vendor/device ID pair for D-Link DUB-E250
- r8152: try to use a normal budget
- r8152: set bp in bulk
- r8152: adjust generic_ocp_write function
- r8152: fix the autosuspend doesn't work
- r8152: Add __GFP_NOWARN to big allocations
- r8152: reduce the control transfer of rtl8152_get_version()
- r8152: remove rtl_vendor_mode function
- r8152: avoid to change cfg for all devices
- r8152: add USB device driver for config selection
- r8152: use napi_gro_frags
- cdc_ether: no need to blacklist any r8152 devices
- cdc_ether: add u-blox 0x1313 composition
- use color, function, function-enumerator properties.
- removes the label properties from LED nodes.
- add panic-indicator to the blue power/status LED.
Note: yes this brings the combined LAN/"switch" LED sort of back,
though I fully admit, it's a bit jank. Do you know a better option?
then please tell/make a PR!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Shiji Yang [Tue, 31 Oct 2023 10:47:49 +0000 (18:47 +0800)]
base-files: support parse DT LED color and function
The 'label' property in led node has been deprecated and we'd better
to avoid using it. This patch allows us to extract DT OF LED name
from the newly introduced LED properties "color", "function" and
"function-enumerator".
Russell Senior [Fri, 1 Dec 2023 21:48:56 +0000 (13:48 -0800)]
qoriq: pad rootfs with zeros
Presently, sysupgrade -n does *not* reset the overlayfs, retaining
unwanted filesystem contents. Adding PADDING=1 in front of
gen_image_generic.sh in image/Makefile ensures that the overlayfs is
recreated on firstboot.
Fixes: 080a769b4da8 ("qoriq: new target") Signed-off-by: Russell Senior <russell@personaltelco.net>
[add Fixes tag, rewrite commit subject and message to respect line
length] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Russell Senior [Fri, 1 Dec 2023 21:48:55 +0000 (13:48 -0800)]
qoriq: set compat_version in board.d
Currently, sysupgrade without the -n option complains:
# sysupgrade -v tmp/openwrt-qoriq-generic-watchguard_firebox-m300-squashfs-sysupgrade.img.gz
upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n).
upgrade: Kernel switched to FIT uImage. Update U-Boot environment.
upgrade: Reading partition table from bootdisk...
upgrade: Extract boot sector from the image
upgrade: Reading partition table from image...
Image check failed.
So, add the missing 05_compat-version to /etc/board.d/ to allow
sysupgrade to save config without using -f.
Fixes: c4b499bc03ab ("qoriq: use FIT uImage for Firebox M300 kernel") Signed-off-by: Russell Senior <russell@personaltelco.net>
[drop invalid copyright header, add SPDX license header, shorten commit
subject, add fixes tag] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Remove upstreamed patches:
* replace usage of the deprecated "pci-dma-compat.h" API (6c03b27)
* remove uaccess and get_fs calls from PCIe for Kenel >= 5.18 (1d0d08c)
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
projects / thirdparty / openwrt.git / log
