Jean Thomas [Thu, 9 Nov 2023 10:28:45 +0000 (11:28 +0100)]
mediatek: Add support for GL.iNet X3000 (Spitz AX) and XE3000 (Puli AX)
The GL.iNet X3000 and XE3000 are Wi-Fi 6 5G cellular routers, based on
MediaTek MT7981A SoC. The XE3000 is the same device as the X3000,
except for an additional battery.
Specifications:
- SoC: Filogic 820 MT7981A (1.3GHz)
- RAM: DDR4 512M
- Flash: eMMC 8G, MicroSD card slot
- WiFi: 2.4GHz and 5GHz with 6 antennas
- Ethernet:
- 1x LAN (10/100/1000M)
- 1x WAN (10/100/1000/2500M)
- 5G: Quectel RM520N-GL with two nano-SIM card slots
- USB: 1x USB 2.0 port
- UART:
- 3.3V, TX, RX, GND / 115200 8N1
MAC addresses as verified by OEM firmware:
vendor OpenWrt address source
WAN eth0 label factory 0x0a (label)
LAN eth1 label + 1
2g phy0-ap0 label + 2 factory 0x04
5g phy1-ap0 label + 3
Installation via U-Boot rescue:
1. Press and hold reset button while booting the device
2. Wait for the Internet led to blink 5 times
3. Release reset button
4. The rescue page is accessible via http://192.168.1.1
5. Select the OpenWrt sysupgrade image and start upgrade
6. Wait for the router to flash new firmware and reboot
Revert to stock firmware:
1. Download the stock firmware from GL.iNet website
2. Use the method explained above to flash the stock firmware
Switch the modem network port between PCIe and USB interfaces:
1. Connect to the AT commands (/dev/ttyUSB2) port using
e.g. minicom: minicom -D /dev/ttyUSB2
2. Check the current modem mode with 'AT+QCFG="data_interface"':
- 0,0 indicates that the network port uses the USB interface
- 1,0 indicates that the network port uses the PCIe interface
3. Switch the active interface with:
- 'AT+QCFG="data_interface",0,0' to use the USB interface
- 'AT+QCFG="data_interface",1,0' to use the PCIe interface
4. Reboot
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
Jean Thomas [Thu, 7 Dec 2023 15:18:02 +0000 (16:18 +0100)]
mediatek: mt7981: pinctrl: add additional emmc groups
Add new emmc groups in the pinctrl driver for the
MediaTek MT7981 SoC:
* emmc reset, with pin 15.
* emmc 4-bit bus-width, with pins 16 to 19, and 24 to 25.
* emmc 8-bit bus-width, with pins 16 to 25.
The existing emmc_45 group is kept for legacy reasons, even
if this is the union of emmc_reset and emmc_8 groups.
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
Daniel Golle [Wed, 13 Mar 2024 18:44:52 +0000 (18:44 +0000)]
generic: mtk_eth_soc: fix PPE hanging issue
A patch to resolve an issue was found in MediaTek's GPL-licensed SDK:
In the mtk_ppe_stop() function, the PPE scan mode is not disabled before
disabling the PPE. This can potentially lead to a hang during the process
of disabling the PPE.
Without this patch, the PPE may experience a hang during the reboot test.
Liu Dongmiao [Tue, 12 Mar 2024 06:48:08 +0000 (06:48 +0000)]
libevent2: make cmake use relative imported path
libevent2's cmake use absolute path, then cmake cannot find it when cross compiling:
```
-- Found libevent include directory: /builder/staging_dir/target-mips_24kc_musl/usr/include
-- Found libevent component: /builder/staging_dir/target-mips_24kc_musl/usr/lib/libevent_core.so
-- Found libevent component: /builder/staging_dir/target-mips_24kc_musl/usr/lib/libevent_extra.so
-- Found libevent component: /builder/staging_dir/target-mips_24kc_musl/usr/lib/libevent_openssl.so
-- Found libevent 2.1.12 in /builder/staging_dir/target-mips_24kc_musl/usr
CMake Error at /builder/staging_dir/target-mips_24kc_musl/usr/lib/cmake/libevent/LibeventTargets-shared.cmake:102 (message):
The imported target "libevent::core" references the file
"/usr/lib/libevent_core-2.1.so.7.0.1"
but this file does not exist. Possible reasons include:
* The file was deleted, renamed, or moved to another location.
* An install or uninstall procedure did not complete successfully.
* The installation package was faulty and contained
Mikhail Zhilkin [Sat, 2 Mar 2024 19:58:40 +0000 (19:58 +0000)]
ramips: add support for Z-ROUTER ZR-2660
This commit adds support for Z-ROUTER ZR-2660 (also known as Routerich
AX1800) wireless WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (AMD/Spansion S34ML01G2)
- WLAN :
- 2.4 GHz : MediaTek MT7905D/MT7975 (14c3:7916), b/g/n/ax, MIMO 2x2
- 5 GHz : MediaTek MT7915E (14c3:7915), a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- USB : 1x 2.0
- UART : 3.3V, 115200n8, pins are silkscreened on the pcb
- Buttons : 1x Reset
- LEDs : 1x WiFi 2.4 GHz (green)
1x WiFi 5 GHz (green)
1x LAN (green)
1x WAN (green)
1x WAN no-internet (red)
- Power : 12 VDC, 1 A
Installation
------------
1. Run tftp server on your PC (IP: 192.168.2.2) and put OpenWrt initramfs
image (initramfs.bin) to the tftp root dir
2. Open the following link in the browser to enable telnet:
http://192.168.2.1/cgi-bin/telnet_ssh
3. Connect to the router (default IP: 192.168.2.1) using telnet shell
(credentials - user:admin)
4. Run the following commands in the telnet shell (this will install
OpenWrt initramfs image on nand flash):
cd /tmp
tftp -g -r initramfs.bin 192.168.2.2
mtd write initramfs.bin firmware
mtd erase firmware_backup
reboot
5. Copy OpenWrt sysupgrade image (sysupgrade.bin) to the /tmp dir of the
router
6. Connect to the router (IP: 192.168.1.1) using ssh shell and run
sysupgrade command:
sysupgrade -n /tmp/sysupgrade.bin
Return to stock
---------------
1. Copy stock firmware (stock.bin) to the /tmp dir of the router using scp
2. Run following command in the router shell:
cd /tmp
mtd write stock.bin firmware
reboot
Recovery
--------
Connect uart (pins are silkscreened on the pcb), interrupt boot process by
pressing any key, use u-boot menu to flash stock firmware image or OpenWrt
initramfs image.
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | 24:0f:5e:xx:xx:4c | label |
| WAN | 24:0f:5e:xx:xx:4d | label+1 |
| WLAN 2g | 24:0f:5e:xx:xx:4e | label+2 |
| WLAN 5g | 24:0f:5e:xx:xx:4f | label+3 |
+---------+-------------------+-----------+
The WLAN 2.4 MAC was found in 'factory', 0x4
The LAN MAC was found in 'factory', 0xfff4
The WAN MAC was found in 'factory', 0xfffa
Robert Marko [Tue, 12 Mar 2024 04:06:14 +0000 (00:06 -0400)]
kernel: config: 6.6: disable ZSTD debug info compression by default
When kernel 6.6 is being compiled with GCC13 it will prompt for:
Compressed Debug information
> 1. Don't compress debug information (DEBUG_INFO_COMPRESSED_NONE)
2. Compress debugging information with zlib (DEBUG_INFO_COMPRESSED_ZLIB)
3. Compress debugging information with zstd (DEBUG_INFO_COMPRESSED_ZSTD) (NEW)
This is because kernel now also has support for compressing debug info
with ZSTD, so add the missing symbol and disable it by default.
Flash instructions:
The vendor firmware is based on OpenWrt, the sysupgrade image can be
flashed using the '-F' (force) option on the CLI.
Make sure not to keep settings when doing so.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CharlesMengCA [Tue, 12 Mar 2024 04:06:14 +0000 (00:06 -0400)]
kernel: config: add symbol introduced with 6.2
CONFIG_DEBUG_INFO_COMPRESSED_ZSTD, required by GCC 13.0+
Compress the debug information using zstd. This may provide better compression than zlib, for about the same time costs, but requires newer toolchain support. Requires GCC 13.0+ or Clang 16.0+, binutils 2.40+, and zstd.
Daniel Golle [Mon, 11 Mar 2024 23:23:23 +0000 (23:23 +0000)]
kernel: modules: don't override NLS dependencies
Recent changes for Linux 6.6 broke things when building with older
kernels:
Package kmod-fs-jfs is missing dependencies for the following libraries:
nls_base.ko
Fix this by adding NLS dependencies after the added dependency applying
on Linux 6.6.
Fixes: f9198480da ("kernel: modules: fs: adapt for kernel 6.6") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Robert Marko [Thu, 7 Mar 2024 14:08:27 +0000 (15:08 +0100)]
kernel: crypto: add kmod-crypto-geniv as dependency to modules that use it
Now that geniv is packaged separately for kernel 6.6, we need to add it
as a dependency to kmod-crypto-seqiv and kmod-crypto-echainiv that require
it under kernel 6.6.
Tan Zien [Sun, 3 Mar 2024 16:57:03 +0000 (00:57 +0800)]
kernel: modules: hwmon: adapt for kernel 6.6
Adapt hwmon kmods for building under kernel 6.6:
* ad7418 now requires regmap
* Invert criteria to allow adt7410 be built with Linux 6.1 as well
as Linux 6.6.
Weijie Gao [Sun, 3 Mar 2024 14:07:29 +0000 (22:07 +0800)]
kernel: modules: crypto: adapt for kernel 6.6
Adapt crypto kmods for building under kernel 6.6:
* mpi.ko moved from lib/mpi/mpi.ko to lib/crypto/mpi/mpi.ko
* jitterentropy_rng requires SHA3 support for kernel 6.6
Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Tan Zien <nabsdh9@gmail.com> Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Weijie Gao [Sat, 6 Jan 2024 08:19:10 +0000 (16:19 +0800)]
kernel: modules: video: adapt for kernel 6.6
Adapt video kmods for building under kernel 6.6:
* Add drm_exec.ko and drm_suballoc_helper.ko for kmod-drm as they
are added since 6.6 and 6.4
* Add uvc.ko for kmod-video-uvc as related contents was split as a
new module since 6.3
Signed-off-by: Tan Zien <nabsdh9@gmail.com> Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Weijie Gao [Sat, 6 Jan 2024 08:12:06 +0000 (16:12 +0800)]
kernel: modules: block: adapt for kernel 6.6
Adapt block kmods for building under kernel 6.6:
* To build scsi_transport_iscsi.ko, change CONFIG_SCSI_ISCSI_ATTRS
from =y to =m as this config is always tristate since 2.6.
Weijie Gao [Sat, 6 Jan 2024 07:56:26 +0000 (15:56 +0800)]
kernel: modules: fs: adapt for kernel 6.6
Adapt fs kmods for building under kernel 6.6:
* Add kmod-fs-netfs as dependency for kmod-fs-9p
* Add kmod-fs-netfs as dependency for fs-smbfs-common as netfs is
required for cifs since 6.3
* Add new kmod-nls-ucs2-utils as dependency for smbfs/jfs as UCS2
support was split as new module since 6.6.
* Add kmod-lib-zlib-deflate and kmod-lib-zlib-inflate as
dependencies for kmod-pstore due to crypto API compression was
replaced with zlib_deflate library calls since 6.6
* Remove nfs_ssc.ko from kmod-fs-nfs-common. The nfs_ssc was no
longer a kernel module described by NFS_V4_2_SSC_HELPER since 5.13 [1]
Weijie Gao [Sat, 6 Jan 2024 07:17:17 +0000 (15:17 +0800)]
kernel: modules: usb: adapt for kernel 6.6
Adapt usb kmods for building under kernel 6.6:
* Add kmod-phylink as dependency for usb-net-asix
* Add kmod-net-selftests as dependency for usb-net-smsc95xx
* Add kmod-iio-core as dependency for usb-hid-mcp2221 as ADC/DAC
support was added since 6.2 which requires IIO.
Daniel Golle [Sat, 2 Mar 2024 04:21:29 +0000 (04:21 +0000)]
kernel: modules: netdevices: adapt for kernel 6.6
Adapt netdevices kmods for building under kernel 6.6:
* Add missing module dependency for kmod-stmmac-core on kmod-of-mdio.
* Invert criteria to allow Airoha EN8811H PHY driver to build with
Linux 6.1 as well as Linux 6.6.
* Mellanox mlx5 driver started exposing thermal sensors and now it requires
hwmon
Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Weijie Gao [Sat, 6 Jan 2024 07:09:12 +0000 (15:09 +0800)]
kernel: modules: netsupport: adapt for kernel 6.6
Adapt netsupport kmods for building under kernel 6.6:
* common part of mqprio was split into a new Kconfig since 6.3.
Add new kmod-sched-mqprio-common as dependency for kmod-sched-mqprio.
Weijie Gao [Sat, 6 Jan 2024 07:08:41 +0000 (15:08 +0800)]
kernel: modules: input: adapt for kernel 6.6
Adapt input kmods for building under kernel 6.6:
* kmod-input-touchscreen-edt-ft5x06 depends on kmod-regmap-i2c
from 6.3 as it starts to use regmap to access registers
* CONFIG_HID_SUPPORT needs to be set in addition to CONFIG_HID.
Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Robert Marko [Fri, 1 Mar 2024 13:15:15 +0000 (14:15 +0100)]
generic: 6.6: fix uncompressed kallsyms
Currently, the existing uncompressed kallsym support is causing qualcommax
boards to hang on boot, and only after earlycon and verbose BUG() prints
are enabled the trace is visible:
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] kernel BUG at kernel/kallsyms.c:340!
[ 0.000000] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
Felix has fixed up the uncompressed kallsyms support so modify the current
patch with the fix.
All credits for the code go to Felix.
Weijie Gao [Tue, 9 Jan 2024 15:20:18 +0000 (23:20 +0800)]
tools: add util-linux
since kernel 6.4, commit bca2f3a9406b ("efi/zboot: Add BSS padding
before compression") introduces the use of hexdump to padding the
EFI kernel binary before compression.
util-linux which containing hexdump should then be compiled as a host
tool to guarantee not breaking the kernel build process.
Daniel Golle [Mon, 11 Mar 2024 18:32:38 +0000 (18:32 +0000)]
mediatek: mt7988: fix clk for 2nd PCIe port
Due to what seems to be an undocumented oddity in MediaTek's MT7988
SoC design the CLK_INFRA_PCIE_PERI_26M_CK_P2 clock requires
CLK_INFRA_PCIE_PERI_26M_CK_P3 to be enabled.
This currently leads to PCIe port 2 not working in Linux.
Reflect the apparent relationship in the clk driver to make sure PCIe
port 2 of the MT7988 SoC works.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The lldpd man page says that "configure lldp tx-interval" can
specify an interval value in milliseconds by appending a "ms" suffix to
the figure. Thus mandating string handling, and not integer comparison.
Bump to 2.90 to get upstream's fix for DNSSEC KeyTrap (CVE-2023-50387,
CVE-2023-50868) among many other goodies and fixes (notably, upstream 568fb024... fixes a UAF in cache_remove_uid that was routinely crashing
dnsmasq in my deployment).
Olliver Schinagl [Fri, 23 Feb 2024 21:54:48 +0000 (22:54 +0100)]
scripts: Kernel bumper script
For years, we have struggled and been frustrated at loosing history of
files in git, due to the 'copy + add' strategy. This could have been
prevented with a double-commit 'mv + add' trick.
On the mailing list [0] the discussion was started to put the
instructions in a wiki. Instead, it is much better to just script it and
put it in the repo.
Instead of doing mv + copy, which leads to two commits, but no history
on the copied files, it uses move, + copy and merge, which results in
three (merge) commits, but keeps the history of all files. As always
with renames, `--follow` will be needed.
The tool is trivial and works either in the OpenWrt git root directory,
or in the actual target directory.
Tested on the `realtek` and generic targets.
Note, that the tool does not do any of the labor needed after the move,
such as updating configs, dropping patches etc.
To make sure this script is easily found by any developer, who just
wants to do a kernel bump, the script is added here and not to
maintainer-tools repo as those scripts are a little bit more specialized.
Bumping a kernel is a trivial task that often regular developers do,
where most do not even know the existence of maintainer tools, are not
part of the main repo they'd clone, not part of the docker container
they'd use and so discoverability is probably much more important.
Kyle Hendry [Sun, 18 Feb 2024 20:26:38 +0000 (12:26 -0800)]
bmips: add support for SmartRG SR505n
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 16MB SPI NOR W25Q128WFG
- RAM: 128MB DDR3 W631GG6KB-15
- Ethernet: 1x 1000M, 3x 100M
- Wifi: BCM435F
- 1x USB 2.0 port
- 3x Button
- 12x LED
Flashing via serial
- Connect to the 3.3V TTL UART on the board
(J6 pinout Vcc Rx Tx Gnd) at 115200-8-N-1
- Press any key in the serial console when powering up the board to enter
the CFE prompt
- Configure an interface on your workstation to static IP 192.168.1.100
and connect it to the board
- Start a TFTP server with the firmware image
- On the CFE prompt, enter the command
"f 192.168.1.100:openwrt-bmips-bcm63268-smartrg_sr505n-squashfs-cfe.bin"
Zoltan HERPAI [Mon, 1 Jan 2024 12:50:46 +0000 (13:50 +0100)]
usb: add cdns3 support
CDNS3 is a SuperSpeed (SS) USB 3.0 Dual-Role-Device (DRD) controller from
Cadence. Add support for this device, and add the required symbols into
the generic configs.
Sungbo Eo [Sun, 4 Feb 2024 18:57:27 +0000 (03:57 +0900)]
ramips: add factory image for ipTIME AX2004M
Unlike the recovery image, this initramfs-factory image can be flashed
using the stock firmware web interface (from any active boot partition),
as well as the bootloader recovery web page. Drop the recovery image in
favor of the factory image.
Installation via stock/recovery web interface:
1. Flash **initramfs-factory** image through the web page.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Sungbo Eo [Sun, 4 Feb 2024 13:10:29 +0000 (22:10 +0900)]
ramips: mt7621: use variable for relocate-kernel argument
The "0x80001000" address logically comes from "loadaddr-y" variable for
mt7621 subtarget. Let's replace the hardcoded value with the predefined
variable. This change is purely cosmetic.
Sungbo Eo [Sun, 4 Feb 2024 12:46:14 +0000 (21:46 +0900)]
ramips: rename mtd partition of ipTIME NAND devices
Contrary to common ipTIME NOR devices, the "Config" partition of T5004
and AX2004M contain normal U-Boot environment variables. Renaming the
partition into "u-boot-env" serves for better description, and it also
conforms to common naming practice in OpenWrt.
This patch might also be extended to A3004T, but its u-boot-env
partition layout has not been confirmed yet.
Sungbo Eo [Sun, 17 Dec 2023 16:06:21 +0000 (01:06 +0900)]
ramips: add NMBM support for ipTIME AX2004M
AX2004M uses NMBM on its NAND flash, but it was not enabled in DTS as the
device support [1] had been added before NMBM feature in mtk_bmt driver [2].
Let's enable it now.
With this change, there is a low possibility of boot failure after
sysupgrade from older versions. As AX2004M already has gone through
two stable releases in the meantime, it would be safe to warn users
by bumping DEVICE_COMPAT_VERSION.
[1] 37753f34ac68 ("ramips: add support for ipTIME AX2004M")
[2] 06382d1af7b2 ("kernel: add support for mediatek NMBM flash mapping support")
Installation COVR Point A:
* In factory reset state: OEM Web UI is at 192.168.0.50
no DHCP, skip wizard by directly accessing:
http://192.168.0.50/UpdateFirmware_Simple.html
* After completing setup wizard: Web UI is at 192.168.0.1
DHCP enabled, login with empty password
* Flash factory.bin
* Perform a factory reset to restore OpenWrt UCI defaults
Installation COVR Points B:
* OEM Web UI is at 192.168.0.50, no DHCP, empty password
* Flash factory.bin
* Perform a factory reset to restore OpenWrt UCI defaults
Recovery:
* Keep reset button pressed during power on
* Recovery Web UI is at 192.168.0.50, no DHCP
* Flash factory.bin
used to work best with Chromium-based browsers or curl:
curl -F firmware=@factory.bin \
http://192.168.0.50/upgrade.cgi
since this fails to work on modern Linux systems,
there is also a script dlink_recovery_upload.py
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
projects / thirdparty / openwrt.git / log
