Flash instructions:
1. Download and flash the vendor migration firmware via webUI:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7986-jdcloud_re-cp-03-vendor-migration.bin
(Default address is 192.168.68.1, user root, no password)
2. After device has booted up, write new GPT table:
dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
Justin Klaassen [Sat, 13 Jan 2024 20:28:57 +0000 (20:28 +0000)]
rockchip: fix boot from non-MMC devices
Booting from non-MMC devices on Rockchip targets without this
change results in a boot failure:
Model: FriendlyElec NanoPi R5S
Net: eth0: ethernet@fe2a0000
Hit any key to stop autoboot: 0
** Booting bootflow 'nvme#0.blk#1.bootdev.part_1' with script
** No partition table - mmc 0 **
** No partition table - mmc 0 **
Couldn't find partition mmc 0:1
Can't set block device
Wrong Image Type for bootm command
ERROR -91: Protocol wrong type for socket: can't get kernel image!
Boot failed (err=1)
This change fixes the default boot script for Rockchip targets to
support booting from non-MMC devices such as NVMe or USB drives.
Some targets with only a boot rom (e.g. NanoPi R5S) may require u-boot
to be installed on the eMMC or a MicroSD card in order to boot from
non-MMC devices.
Cedric DOURLENT [Fri, 12 Jan 2024 08:23:46 +0000 (09:23 +0100)]
build: add option for building with stack-protector-all
The GCC option -fstack-protector-all is a security feature used to protect against stack-smashing attacks.
This option enhances the stack-smashing protection provided by -fstack-protector-strong.
-fstack-protector-all option applies stack protection to all functions, regardless of their characteristics.
While this offers the most comprehensive protection against stack-smashing attacks, it can significantly impact
the performance of the program because every function call includes additional checks for stack integrity.
This option can incur a performance penalty because of the extra checks added to every function call,
but it significantly enhances security, making it harder for attackers to exploit buffer overflows to execute arbitrary code.
It's particularly useful in scenarios where security is paramount and performance trade-offs are acceptable.
Felix Fietkau [Fri, 19 Jan 2024 13:48:05 +0000 (14:48 +0100)]
mediatek: fix WED + wifi reset
The WLAN + WED reset sequence relies on being able to receive interrupts from
the card, in order to synchronize individual steps with the firmware.
When WED is stopped, leave interrupts running and rely on the driver turning
off unwanted ones.
WED DMA also needs to be disabled before resetting.
David Bauer [Thu, 18 Jan 2024 21:47:17 +0000 (22:47 +0100)]
hostapd: ACS: Fix typo in bw_40 frequency array
[Upstream Backport]
The range for the 5 GHz channel 118 was encoded with an incorrect
channel number.
Fixes: ed8e13decc71 (ACS: Extract bw40/80/160 freqs out of acs_usable_bwXXX_chan()) Signed-off-by: Michael Lee <michael-cy.lee@mediatek.com> Signed-off-by: David Bauer <mail@david-bauer.net>
The raspberypi/userland repository has been deprecated and the RPi tools have
been moved to the raspberrypi/utils repository.
https://github.com/raspberrypi/userland/commit/96a7334ae9d5fc9db7ac92e59852377df63f1848
Shiji Yang [Tue, 16 Jan 2024 11:56:05 +0000 (19:56 +0800)]
ramips: mt7621: convert MT7915 EEPROM to NVMEM format
Some MT7915 calibration data consists of two parts. The first part
"eeprom" size is 0xe00. The second part "precal" size is 0x19c10.
Though some devices may not have precal data, it's better to assume
that precal data exists as no users/developers confirm it. On the
other hand, some devices definitely do not contain precal data
because the EEPROM partition size is smaller than the precal NVMEM
cell size.
raspberrypi/firmware is about 40G, so getting the full history log isn't an
option.
There have been multiple improvements and also support for the RPi 5 has been
added.
Marty Jones [Mon, 25 Dec 2023 00:03:31 +0000 (19:03 -0500)]
bcm27xx-userland: update to latest version
This is the last update for bcm27xx-userland as it has been
deprecated but funcional up to raspberry pi 5.
96a7334 README: Update to make it clear that most code in this repo is deprecated 3c97f76 userland: dtoverlay: /boot/firmware is a valid path 153a235 Assorted clang static analysis fixes eca070c bcm_host: Update kms/fkms check for pi5 06a7618 dtoverlay: Support bcm2712 as a platform 0489c07 dtoverlay: Add dtoverlay_first/next_subnode a1c7f81 dtoverlay: Support literal assignments of path strings 44a3953 raspivid: Also flush PTS file if flush is enabled cc1ca18 userland: dtoverlay: Use os_prefix if set 9d5250f libfdt: Add null-ptr check for prop-data to resolve clang --analyzer warning 50527c6 mmal: Only include Videocore components if not running on Videocore df245ea tvservice: Update unsupported message to recommend kmsprint de0cfe8 dtoverlay: Fix clang warnings 0182f05 dtoverlay: Fix various compiler warnings 2a6306b dtoverlay: Fix path rebasing and exports d1e92d7 dtoverlay: Add support for string escape sequences b1ee39e gencmd: Add a fallback to mailbox interface if vchiq is not available 54fd97a hello_pi: Fix some build issues
Flash instruction, web UI:
1. Set a static IP on your computer compatible with 192.168.1.1, i.e
192.168.1.100.
2. Connect the ethernet cable from your computer to the router.
3. Make sure the router is powered off.
4. Press the reset button, don't release it yet!
5. While pressing reset, power on the router.
6. Wait 10 seconds or more.
Note: The power LED is red at first then turns to solid green when
ready.
7. Release the reset button.
8. Browse to 192.168.1.1
9. Select .bin file.
10. Upgrade the image.
11. Wait for it to reboot.
Yangyu Chen [Mon, 18 Dec 2023 19:21:53 +0000 (03:21 +0800)]
bcm27xx: 6.1: turn on cpu erratum for A72 and disable A53
The original configuration might be copied from bcm2710 which uses
cortex A53 rather than A72 in BCM2711, without errata might be harmful
to system stability and security.
Hauke Mehrtens [Wed, 10 Jan 2024 21:10:28 +0000 (22:10 +0100)]
bcm27xx: Remove unneeded kernel patch
This problem was fixed upstream in a different way, see:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-6.1.y&id=f434703fb893ddffcdbc1eec7646ce321e1190a8
Drop PSGMII PHY patch as it has been moved to generic in preparation for
the PHY driver to be also used for ipq807x SoC as the same PHY is also
used there.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Bryan Berg [Sun, 26 Nov 2023 21:34:01 +0000 (13:34 -0800)]
ipq806x: Stabilize LAN 2 MAC address, interface ordering
Part 1 of #13629 split.
* Sets the LAN 2 MAC address in the DTS by deriving it from LAN 1's
address. The factory OS derives this from the `eth1addr` u-boot env
variable, but the nvmem_u-boot-env driver doesn't support parsing MAC
addresses from fields other than `ethaddr`. But for all of the device
samples I've checked (~10) it derives the correct MAC.
* Updates 02_network to ensure that interfaces are assigned to roles
correctly and consistently.
generic: 6.1: initial backport of at803x PHY driver cleanup
Initial backport of at803x PHY driver cleanup. This is in preparation
for split and addition of new PHY Family based on at803x needed for
ipq807x and other IPQ Series SoC.
Other affected patch are automatically refreshed with
make target/linux/refresh
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It shouldn't gate on the value, since the value will ostensibly
always be set; instead it should depend on the variable being
prepended to being non-empty.
Fixes #14403
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Peter Körner [Tue, 19 Sep 2023 22:44:39 +0000 (00:44 +0200)]
rtl838x: fix RTL838X_LED_SW_CTRL definition
According to https://svanheule.net/realtek/maple/register/led_sw_ctrl and also
drivers/net/dsa/rtl83xx/debugfs.c LED_SW_CTRL on the RTL838X should be 0xa00c
not 0x0128. Please note, that is is 0x0128 on the RTL8390/cypress SOC family.
To prevent use of host's library path on Void Linux:
/usr/lib/libacl.so: file not recognized: file format not recognized
collect2: error: ld returned 1 exit status
libtool: error: error: relink 'libgettextlib.la' with the above command before installing it
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
Thomas Schröder [Wed, 10 Jan 2024 10:12:10 +0000 (11:12 +0100)]
mediatek: GL-MT6000: Change LED colors
Fine tuning PR: openwrt/openwrt#14355 Ref: 5a82bb909bf1
("mediatek: GL-MT6000: Add missing LED state definitions")
As the only LED is using white in the stock firmware when the device is
running and blue for the bootloader I suggest following changes:
- Using blue for the BL and preinit+failsafe
- White for normal operation (like the original FW) and sysupgrade
With this changes it's clear by looking to the LED in which operation
mode the device is and a possible BL stuck can be seen easily.
Tested with [GL-MT6000](https://openwrt.org/toh/gl.inet/gl-mt6000).
Signed-off-by: Thomas Schröder <tschroeder_github@outlook.com> Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
MAC Address: LAN1 (label) at APPSBL partition
LAN2: label + 1
WLAN2: label + 8
WLAN5: label + 16
Installation
------------
Connect to the RJ45 console (TTL)
Connect LAN1 to host, set host ip as 192.168.1.10
Start a tftp server to serve the initramfs image
Open console connection (9600n8)
Connect power through the DC jack
`Hit any key to stop autoboot: 5`: press any key
`Enter G,Q,or H:`: press `K` to access the hidden option
`Enter password:`: `fap22b1!$` to access a limited u-boot console
`(FAP) #`: `tftpboot your_initramfs_image_name.itb`
`(FAP) #`: `bootm`
Once OpenWrt has booted, install the firmware through sysupgrade
a-gave [Thu, 11 Jan 2024 10:33:21 +0000 (11:33 +0100)]
imagebuilder: copy from buildroot only target/linux/generic and target/linux/<target> to reduce the size
This reduces the size of a single imagebuilder by about 40MB
In example for the target ath79 it would be the sum of generic and <target> directories, so about 16MB,
instead of the whole size of the target directory, about 53MB:
11M target/linux/generic/
3.9M target/linux/ath79/
base-files: add support for rootfs mount options from cmdline
Add support for configuring rootfs mount options from cmdline.
Rootfs mount options can be passed by declaring in the kernel
cmdline as much options as needed prefixed with "rootfs_mount_options."
An example usage is with rootfs with F2FS filesystem to enable
compress_algorithm to reduce flash wear by compressing the files before
writing to flash.
Example usage:
"... rootfs_mount_options.compress_algorithm=zstd ..."
To pass multiple options:
"... rootfs_mount_options.compress_algorithm=zstd rootfs_mount_options.noinline_data ..."
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
97bacb70138a libfstools: query drivers by priority 41e619ed1352 block: recognize /dev/fit* block devices bc3b8cdd3de3 libfstools: add uImage.FIT fitblk driver 846302d09246 libfstools: partname: raise priority to 25 1a5695925ecf mount_root: add support for passing args to mount_root start 1858a492c300 mount_root: permit to pass mount options for rootfs mount
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Chukun Pan [Wed, 20 Dec 2023 15:15:31 +0000 (23:15 +0800)]
mediatek: Cudy WR3000: simplify mac address setup
The mac address of the network port under the switch is
the same as the corresponding gmac by default, so there
is no need to repeat the setting. Compile test only.
Jacob Potter [Sun, 24 Dec 2023 02:37:54 +0000 (21:37 -0500)]
realtek: rtl838x: add Netgear GS110TUP v1 support
The GS110TUP v1 is a managed switch similar to the GS110TPP v1, but with
port 10 as SFP instead of RJ-45 and a total budget of 240 watts. Ports
1-4 support 60-watt 802.3bt PoE and ports 5-8 support 30-watt 802.3at.
The flash layout of the two switches are identical, and the U-Boot
configurations are the same except for having a different magic number,
so installation can be done via the same U-Boot method.
The following command will be needed to enable the port LEDs as per
https://forum.openwrt.org/t/72510/51 :
fw_setenv bootcmd "rtk network on; boota"
Additionally, port 9 (1000base-T from a separate QSGMII PHY) does not
function without this. Port 10 was not tested as no SFP module was
available.
Signed-off-by: Jacob Potter <jacob@j4cbo.com>
[rebase on merged flash layout] Signed-off-by: Sander Vanheule <sander@svanheule.net>
This reverts commit b7f9742da82fa9b122e8d63e48a9a5c0dec298f2.
There are several reports of regressions with this commit. Will be added
back once I've figured out and fixed the cause
Felix Fietkau [Sun, 22 Oct 2023 16:00:08 +0000 (18:00 +0200)]
mac80211.sh: fix deadlock on configuring multiple PHYs simultaneously
When hitting a timing window where ubus configuration calls are hitting hostapd
and wpa_supplicant simultaneously, they can deadlock waiting for each other.
Fix this by using a lock around the ubus calls.
David Bauer [Tue, 9 Jan 2024 19:52:56 +0000 (20:52 +0100)]
ath79: read back reset register
Read back the reset register in order to flush the cache. This fixes
spurious reboot hangs on TP-Link TL-WDR3600 and TL-WDR4300 with Zentel
DRAM chips.
This issue was fixed in the past, but switching to the reset-driver
specific implementation removed the cache barrier which was previously
implicitly added by reading back the register in question.
Uwe Niethammer [Fri, 10 Nov 2023 01:06:15 +0000 (02:06 +0100)]
uqmi: added timeouts in qmi.sh
Modems which are using qmi do not reply on the 1st sync but they do
on subsequent. Sometimes uqmi is hanging - even when using an early
dummy access to unlock the modem. To always guarantee a proper
initialisation, running or hanging uqmi processes must be stopped
before. All uqmi calls have now a timeout option -t to avoid hanging.
Installation
1. Open web management interface.
2. Go to Settings > System Tools > Firmware upgrade.
3. Select "Browse" and select the OpenWrt image with factory.bin suffix.
4. After selecting "Upgrade" firmware writing process will start.
5. Wait till device reboots, power LED should stay solid when it's fully
booted, then it's ready for configuration through LAN port.
Additional information
With how device manufacturer patrtitioned the flash memory, it's possible
that with default packages set, initial factory.bin image won't be
created. In such case, try to reduce packages amount or use older release
for initial conversion to OpenWrt. Later You can use sysupgrade.bin
image with full set of packages because OpenWrt uses unpartitioned flash
memory space unused by vendor firmware.
Reverting to vendor firmware involves converting firmware using
tplink-safeloader with -z option (can be found in ImageBuilder or SDK)
and forcibly applying converted firmware as sysupgrade.
Known issues
WARNING: after removing casing of the device one is exposed to high
voltage and is in a risk of being electrocuted.
Caution when interfacing whith bootloader, saving its environment either
by issuing "saveenv" or selecting option "1: Load system code to SDRAM
via TFTP." in boot menu, any of those will lead to overwriting part of
kernel. This will lead to need of firmware recovery. The cause of this
issue is bootloader having environment offset on flash at 0x40000,
while kernel starts from 0x20000.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[Wrap long line in DTS] Signed-off-by: Sander Vanheule <sander@svanheule.net>
Rafał Miłecki [Wed, 27 Dec 2023 15:20:45 +0000 (16:20 +0100)]
uhttpd: handle reload after uhttpd-mod-ubus installation using postinst
Use postinst script to reload service instead of uci-defaults hack. It's
possible thanks to recent base-files change that executes postinst after
uci-defaults.
This fixes support for uhttpd customizations. It's possible (again) to
adjust uhttpd config with custom uci-defaults before it gets started.
Cc: Hauke Mehrtens <hauke@hauke-m.de> Fixes: d25d281fd668 ("uhttpd: Reload config after uhttpd-mod-ubus was added")
Ref: b799dd3c705d ("base-files: execute package's "postinst" after executing uci-defaults") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Harshal Gohel [Wed, 3 Jan 2024 15:15:12 +0000 (16:15 +0100)]
rtl83xx: dsa: reset PVID to 1 instead of 0
Before, PVID is reset for all ports and goes out of bounds. Also, PVID
is later changed by dsa configuration by `ip link` and `bridge vlan`
commands, this does not change the CPU port PVID and CPU PVID stays 0.
It does not allow sending packets from OpenWrt to any connected devices
unless default configuration is changed
This change iterates up to and including cpu_port and sets default PVID
to 1. For lan* ports PVID can be configured with `ip link` and `bridge
vlan` commands
Acked-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Harshal Gohel [Wed, 3 Jan 2024 14:53:47 +0000 (15:53 +0100)]
rtl93xx: dsa: Fix 802.1QinQ for trunk ports
Fix incorrect register value being set for VLAN_PORT_FWD
Before, the 0b1111 would be set for the register which means outgoing
packets would receive an extra tag, corresponding to the PVID of the
port.
On untagged ports, this meant outgoing packets with a single tag.
On tagged ports, this meant outgoing QinQ packets, where the inner tag
was either the PVID of the untagged ingress port, or the already
assigned original (single) tag.
Acked-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Harshal Gohel [Tue, 12 Dec 2023 14:48:56 +0000 (15:48 +0100)]
rtl930x: Rework per port LED configuration
Use led_setX to determine number of LEDs per port. Introduce macros to
calculate register value and shift for particular LED in a particular
set.
Problem with previous implementation is that it uses is10G status to
determine leds per port. However with usxgmii, driver sets 10g, 5g and
2.5g so even though there are only 2 leds per port it selects 4 leds per
port
This implementation relies on configured led_set node.
Acked-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Felix Fietkau [Tue, 9 Jan 2024 14:15:08 +0000 (15:15 +0100)]
mediatek: fix BPI-R3 wifi mac address
Setting/clearing bits on the first byte of the mac address causes collisions
when using multiple SSIDs on both PHYs. Change the allocation to alter the
last byte instead.
Felix Fietkau [Thu, 21 Dec 2023 16:29:45 +0000 (17:29 +0100)]
libubox: work around recent macOS linker change
rpath handling seems to be more restrictive now. To deal with this,
link the libubox library from STAGING_DIR_HOST to STAGING_DIR_HOSTPKG, so that
packages installed to STAGING_DIR_HOSTPKG can pick it up. This mainly affects
ucode, but possibly other host builds as well
I was able to SSH into the stock firmware of my device.
1. Attach the router to the network
2. Use scp (-O) to copy the sysupgrade image
3. Connect using SSH and run `sysupgrade -n`
Option #2 - U-Boot
One way to use the bootloader for flashing is using TFTP:
1. Connect to the router using an ethernet cable
2 Spin up a TFTP server serving the sysupgrade file
3. Open the case and attach a UART
4. Attach power to the router and interrupt the countdown by pressing
any key
5. Select option #2 (Upgrade firmware)
6. Enter IP address information and image name
7. Wait patiently
Co-Authored-By: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net> Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Hannu Nyman [Sat, 6 Jan 2024 17:59:13 +0000 (19:59 +0200)]
mediatek: GL-MT6000: Add missing LED state definitions
Adjust LED names and provide the OpenWrt status indicator aliases
to actually use LEDs by the OpenWrt boot & sysupgrade processes.
* Name both LEDs clearly by the color
* Add the missing OpenWrt LED status indicator aliases and
remove the now unnecessary default status from blue LED
After this commit, the LEDs are used as:
* bootloader, really early Linux boot: blue LED is on
* preinit/failsafe: white LED blinks rapidly
* late boot: white LED blinks slowly
* boot completed, running normally: blue LED is on
Paul Spooren [Sat, 6 Jan 2024 17:50:00 +0000 (18:50 +0100)]
packages: add PKG_URL variable
Using PKG_URL one may set the URL for all sub packages, which is usually
shared anyway. Future packages should only use PKG_URL instead of adding
it per sub-package.
Paul Spooren [Sat, 6 Jan 2024 17:48:46 +0000 (18:48 +0100)]
packages: store URL in Manifest
The manifest should provide as much information as possible about the
package, including the project URL. With this commit the URL is stored
as it's own attribute instead of at the end of the description.
Antennas
--------
The device features internal antennas as well as external antenna
connectors. By default, the internal antennas are used.
Two GPIOs are exported by name, which can be used to control the
antenna-path mux. Writing a logical 0 enables the external antenna
connectors.
Installation
------------
1. Download the OpenWrt sysupgrade image to the device. You can use scp
for this task. The default username and password are "ubnt" and the
device is reachable at 192.168.1.20.
David Bauer [Thu, 30 Nov 2023 06:32:52 +0000 (07:32 +0100)]
mac80211: avoid crashing on invalid band info
Frequent crashes have been observed on MT7916 based platforms. While the
root of these crashes are currently unknown, they happen when decoding
rate information of connected STAs in AP mode. The rate-information is
associated with a band which is not available on the PHY.
Check for this condition in order to avoid crashing the whole system.
This patch should be removed once the roout cause has been found and
fixed.
Chuanhong Guo [Sun, 7 Jan 2024 15:56:05 +0000 (23:56 +0800)]
kernel: copy only *.ko for debug info
Previous commits installed non-elf files into /lib/modules/$VER/.
COLLECT_KERNEL_DEBUG tries to strip all files and these two files
break the build.
Fix it by copying only kernel modules for debug info collection.
Fixes: e1d8e57614 ("kernel: include modinfo for built-in modules") Fixes: 29f6da4340 ("kernel: include built-in module list") Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
projects / thirdparty / openwrt.git / log
