Daniel Golle [Mon, 18 Dec 2023 21:22:12 +0000 (21:22 +0000)]
mvebu: fix RTC of IEI-World Puzzle M90x devices
The Puzzle devices come with an I2C-connected Epson RX8130 RTC.
Disable the (dysfunctional) RTC units of the SoC and add driver
kmod-rtc-ds1307 to support the Epson RX8130 instead.
Tested-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Thibaut VARÈNE [Mon, 11 Dec 2023 14:23:03 +0000 (15:23 +0100)]
dnsmasq: invert logic for "localuse"
Prior to this commit, "localuse" (which enables local resolving through
dnsmsasq) was off by "default". That default was in turn overridden when
"noresolv" was unset (which itself is the default for "noresolv") *and*
"resolvfile" was "/tmp/resolv.conf.d/resolv.conf.auto" (also the default
for this parameter).
In other words, the "default" unset value for "localuse" would only be
ever used in specific *non-default* configurations.
However, the problem with that logic is that a user who wants to ignore
their ISP-provided resolvers by setting "noresolv" to true ends up with
a device that will *only use* said resolvers for local DNS queries,
serving clients' queries via dnsmasq (which now ignores the ISP
resolvers). This can lead to confusion and break random setups as the
DNS lookup performed on clients behalf can differ in their replies from
DNS lookups performed locally on the router.
Furthermore, "localuse" is not configurable through Luci, contrary to
the other two involved settings, adding further confusion for the end
user.
To work around this situation, the logic that sets "localuse" is
inverted: "localuse" now defaults to on by default, and IFF "noresolv"
is unset (default) AND "resolvfile" is changed from default THEN
"localuse" gets turned back off, allowing for more sensible behaviour.
"localuse" value set in config/dhcp still overrides the logic in all
cases, as it did already.
Commit 25746a3fa2da ("drm/i915: fix up merge with usb-next branch") was
internally applied to the 5.15 patch but wasn0t applied to the backport
for kernel 6.1. Apply the same treatement also there to fix compilation
warning.
Fixes: a14240d384af ("kernel: backport list_count_nodes()") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Pawel Dembicki [Fri, 8 Dec 2023 08:32:41 +0000 (09:32 +0100)]
kirkwood: backport fix Ctera C200 V1 ubi part name to 6.1
From the original Patch:
|In 749237967a12 downstream dts was replaced with upstream accepted
|patch. But in upstream version last partition was called "rootfs"
|instead "ubi". OpenWrt require "ubi" label for ubi rootfs.
|This patch restore proper label.
|
|Fixes: 749237967a12 ("kirkwood: Replace dtses with upstream accepted")
|
|Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(patch updated to include 6.1, dropped label properties) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Chukun Pan [Sat, 3 Jun 2023 15:20:13 +0000 (23:20 +0800)]
ipq807x: add support for ZTE MF269
Hardware specifications:
SoC: Qualcomm IPQ8071A
RAM: 512MB of DDR3
Flash1: Eon EN25S64 8MB
Flash2: MX30UF2G18AC 256MB
Ethernet: 2x 2.5G RJ45 port
Phone: 1x RJ11 port (SPI)
USB: 1x Type-C 2.0 port
WiFi1: QCN5024 2.4GHz
WiFi2: QCN5054 5GHz
Button: Reset, WPS
Flash instructions:
1. Connect the router via serial port (115200 8N1 1.8V)
2. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
3. Interrupt U-Boot and run these commands:
tftpboot initramfs.bin
bootm
4. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Robert Marko <robimarko@gmail.com>
Raylynn Knight [Fri, 1 Dec 2023 05:17:07 +0000 (00:17 -0500)]
realtek: Clean up and standardize realtek-poe support
This patch cleans up and standardizes realtek-poe support for realtek
based switches that have supported PoE ports.
The power output of switches supported by realtek-poe package can be
configured in the 02_network ucidef_set_poe() function. This was missed
when some PoE capable switches supported by realtek-poe were added.
The realtek-poe package at one point replaced a lua-rs232 based script
and some devices were not updated to use the realtek-poe package.
Consistently add realtek-poe package to DEVICE_PACKAGES for switches
with supported PoE.
Dirk Buchwalder [Fri, 24 Nov 2023 14:56:39 +0000 (15:56 +0100)]
ipq807x: fix edgecore EAP102 lan/wan
We have a report in the forum, that lan/wan is non-functional
on the EAP102 (https://forum.openwrt.org/t/edgecore-eap102/178449)
Fixing that by swapping label and phy-handle of the dp-nodes and
updating the lan/wan bmp.
Note: the original commiter of the device support seems absent for a
long time in the forum and on the OpenWrt github group.
Tested-by: Antonio Della Selva <antonio.dellaselva@uniurb.it> Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de> Reviewed-by: Robert Marko <robimarko@gmail.com>
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.bin, and host it with tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.bin
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Robert Marko <robimarko@gmail.com>
Chukun Pan [Fri, 20 Oct 2023 15:30:21 +0000 (23:30 +0800)]
kernel: add support for Toshiba TH58NYG3S0HBAI4
Correct oob size from 128 to 256 for Toshiba TH58NYG3S0HBAI4 flash.
Since it is not ONFI compliant NAND, the model name cannot be read
from anywhere, add a static NAND ID entry to correct this.
However, the NAND ID of this flash is inconsistent with the datasheet.
The actual NAND ID is only 4 ID bytes, the last ID byte is missing.[1]
Maybe this flash is counterfeit, or maybe it's another problem.
Another Toshiba flash had the same problem before. Refer to commit a83dc6b ("kernel: move Toshiba-TC58NVG0S3H patch to ipq40xx"), put
the patch into qualcommax target to avoid affecting other devices.
The patch is verified on Arcadyan AW1000.
[1] Datasheet available at (the ID table is on page 50):
https://europe.kioxia.com/content/dam/kioxia/newidr/productinfo/datasheet/201910/DST_TH58NYG3S0HBAI4-TDE_EN_31565.pdf
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Robert Marko <robimarko@gmail.com>
package: kernel: detach of-mdio dependency from stmmac-core
Detach of-mdio dependency from stmmac-core kmod to fix support for
x86_64 target. This target doesn't use OpenFirmware infrastructure and
stmmac-core for the dwmac-intel driver doesn't depends on it.
Add kmod-of-mdio to any other user of stmmac-core as it's not inherit
from stmmac-core anymore.
Explain some of the more obscure logic, or where we deviate from
what the original awk code did. Also, give a count of the usable
addresses on the subnet.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
base-files: ipcalc.sh: Add support for decimal output
This is useful if you later need to perform numeric range-checking
on addresses, i.e. to see if an address falls inside a CIDR range,
etc. and what interface it corresponds to.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Pawel Dembicki [Fri, 8 Dec 2023 08:32:41 +0000 (09:32 +0100)]
kirkwood: fix Ctera C200 V1 ubi part name
In 749237967a12 downstream dts was replaced with upstream accepted
patch. But in upstream version last partition was called "rootfs"
instead "ubi". OpenWrt require "ubi" label for ubi rootfs.
This patch restore proper label.
The kernel patches apply with only minor changes. The only other notable
change is that octeon-usb has moved from staging and had its config
macro renamed from CONFIG_OCTEON_USB to CONFIG_USB_OCTEON_HCD.
Daniel Golle [Fri, 17 Nov 2023 02:25:09 +0000 (02:25 +0000)]
mediatek: add support for Adtran SmartRG Bonanza Peak series
The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s
Wi-Fi 6 residential gateway, access point and mesh router products.
All of them come with an eMMC to boot from, are powered via USB-C and
got a USB 3.0 type-A port. All of them got a Dialog (Renesas) DA14531
Bluetooth module connected via UART. If the device was previously
running stock firmware, the BT chip's internal flash has been loaded
with firmware and it can be attached using hciattach when using
OpenWrt.
* SDG-8612 - Dual-band RJ-45 gateway
2x 2.5G MaxLinear PHY for WAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8614 - Dual-band SFP gateway
1x SFP cage with up to 2.5G speed
1x 2.5G MaxLinear PHY for LAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8622 - Tri-band mesh router
2x 2.5G MaxLinear PHY
The MT7986 2G and 5G are used as 2G and 5G high band.
There’s a MT7915 PCIe card for 5G low band.
* SDG-8632 - Tri-band mesh router with 6 GHz
2x 2.5G MaxLinear PHY
The MT7986 serves the 2G and 6G bands.
There’s a MT7915 PCIe card for 5G.
Installation via U-Boot serial console:
0. setup TFTP server with IP 192.168.1.10/24, place initramfs image
renamed to openwrt.XXX where XXX is the internal product number:
SDG-8612: XXX = 412
SDG-8614: XXX = 414
SDG-8622: XXX = 422
SDG-8632: XXX = 432
1. connect to the serial console and power on the device.
Interrupt the bootloader by pressing 'st'
2. setenv boot_mode openwrt ; saveenv
3. run boot1
Load firmware via TFTP and write to flash
4. run boot2
Now OpenWrt initramfs should boot
5. upload sysupgrade.bin via scp to /tmp
6. sysupgrade
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 10 Dec 2023 01:15:36 +0000 (01:15 +0000)]
kernel: hack: support inverted LEDs on MaxLinear GPY211 PHY
Add downstream DT property to setup the PHY LEDs of the MaxLinear
GPY211 PHY in such way that the VDD of the LED is driven by the SoC
pin rather than the GND (which is the default).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 17 Nov 2023 00:02:05 +0000 (00:02 +0000)]
base-files: add mmc_get_mac_ascii function
Similar to the *_get_mac_binary function, also split the common parts
off mtd_get_mac_ascii into new get_mac_ascii function and introduce
mmc_get_mac_ascii which uses it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add Generic subtarget definition. This is needed to keep consistent name
on every other target/subtarget and also to permit correct work of CI
workflows that expect a target/subtarget pattern.
Fixes: c16b2293fe71 ("ixp4xx: Resurrect IXP4xx support using device tree") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Kamil Jońca [Sun, 5 Nov 2023 13:49:01 +0000 (14:49 +0100)]
ramips: add TP-LINK TL-WR902AC v4
Seems to be very similar to: https://openwrt.org/toh/tp-link/tl-wr902ac_v3
1 x usb
1 x eth
Powered by mini usb port.
Installation:
Can use TFTP method to install:
1. establish TFTP server at 192.168.0.66
2. provide tp_recover.bin file to the TFTP server
3. turn on router with reset button pressed
4. wait for led blinking, then release reset
Specification based on dmesg from already flashed device:
SoC Type: MediaTek MT7628AN ver:1 eco:2
CPU0 revision is: 00019655 (MIPS 24KEc)
Memory: 56028K/65536K available
CPU Clock: 580MHz
WiFi: MT7613BE
MAC addresses are all the same, except wifi5g which last part is decrement by one, ie.:
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (superadmin:xxxxxxxxxx, where
xxxxxxxxxx is a new password from the p.5)
9. Enable SSH access to the router (Settings -> Access control -> SSH)
10. Connect to the router using SSH shell using superadmin account
11. Run in SSH shell:
sh
12. Make a mtd backup (optional, see related section)
13. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
14. Login to the router web interface under admin account
15. Remove dots from the OpenWrt factory image filename
16. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.0.2
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | f4:*:66 |
| WAN | label + 11 | f4:*:71 |
| 2g | label + 2 | f4:*:68 |
| 5g | label + 3 | f4:*:69 |
+-----+------------+---------+
The label MAC address was found in Factory, 0x21000
Florian Eckert [Mon, 7 Aug 2023 09:15:28 +0000 (11:15 +0200)]
tools: add tmon package
Add the 'tmon' packages. This is as a tool to help visualize,
tune, and test the complex thermal subsystem.
We get a compile warning for the tool that the printf format does not
fit. This commit contains a patch that fixes this warning. This patch
has also been sent upstream to the Linux kernel [1].
Felix Fietkau [Tue, 5 Dec 2023 11:59:49 +0000 (12:59 +0100)]
libnl-tiny: update to Git HEAD (2023-12-05)
af57bb123f93 socket: add debug callbacks for rx/tx 785e11aee7dd socket: call rx debug callback once per packet instead of per batch 965c4bf49658 socket: change debug callbacks to pass struct nl_msg
Rafał Miłecki [Mon, 20 Nov 2023 10:46:26 +0000 (11:46 +0100)]
mediatek: filogic: add Acelink EW-7886CAX support
Acelink EW-7886CAX is an MT7986A (AKA Filogic 830) based access point.
It has 512 MiB of RAM, one 2.5 Gbps PoE (802.3at) Ethernet port and
on-SoC Wi-Fi. There is no printed MAC label (on my unit).
My unit came with Mediatek's firmware (based on OpenWrt 21.02)
installed. It was possible to simply upgrade using OpenWrt's sysupgrade
tool.
Another verified upgrade method is using U-Boot (requires UART). During
every boot there is "U-Boot Boot Menu". Selecting option "2. Upgrade
firmware" allows using U-Boot's tftp client to load and flash factory
image.
David Bauer [Mon, 4 Dec 2023 12:54:56 +0000 (13:54 +0100)]
mpc85xx: allow mapping of cpu1 spin-table page
The no-map property was incorrectly added, which kept the system-memory
available on the WS-AP3825 limited to 190MB. We are allowed to map the
page containing the CPU1 spin-table, we are just not allowed to write to
it.
Fixes: 57d7382cb159 ("mpc85xx: increase available RAM on Extreme Networks WS-AP3825i") Signed-off-by: David Bauer <mail@david-bauer.net>
projects / thirdparty / openwrt.git / log
