Hauke Mehrtens [Wed, 10 Jan 2024 21:10:28 +0000 (22:10 +0100)]
bcm27xx: Remove unneeded kernel patch
This problem was fixed upstream in a different way, see:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-6.1.y&id=f434703fb893ddffcdbc1eec7646ce321e1190a8
Drop PSGMII PHY patch as it has been moved to generic in preparation for
the PHY driver to be also used for ipq807x SoC as the same PHY is also
used there.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Bryan Berg [Sun, 26 Nov 2023 21:34:01 +0000 (13:34 -0800)]
ipq806x: Stabilize LAN 2 MAC address, interface ordering
Part 1 of #13629 split.
* Sets the LAN 2 MAC address in the DTS by deriving it from LAN 1's
address. The factory OS derives this from the `eth1addr` u-boot env
variable, but the nvmem_u-boot-env driver doesn't support parsing MAC
addresses from fields other than `ethaddr`. But for all of the device
samples I've checked (~10) it derives the correct MAC.
* Updates 02_network to ensure that interfaces are assigned to roles
correctly and consistently.
generic: 6.1: initial backport of at803x PHY driver cleanup
Initial backport of at803x PHY driver cleanup. This is in preparation
for split and addition of new PHY Family based on at803x needed for
ipq807x and other IPQ Series SoC.
Other affected patch are automatically refreshed with
make target/linux/refresh
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It shouldn't gate on the value, since the value will ostensibly
always be set; instead it should depend on the variable being
prepended to being non-empty.
Fixes #14403
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Peter Körner [Tue, 19 Sep 2023 22:44:39 +0000 (00:44 +0200)]
rtl838x: fix RTL838X_LED_SW_CTRL definition
According to https://svanheule.net/realtek/maple/register/led_sw_ctrl and also
drivers/net/dsa/rtl83xx/debugfs.c LED_SW_CTRL on the RTL838X should be 0xa00c
not 0x0128. Please note, that is is 0x0128 on the RTL8390/cypress SOC family.
To prevent use of host's library path on Void Linux:
/usr/lib/libacl.so: file not recognized: file format not recognized
collect2: error: ld returned 1 exit status
libtool: error: error: relink 'libgettextlib.la' with the above command before installing it
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
Thomas Schröder [Wed, 10 Jan 2024 10:12:10 +0000 (11:12 +0100)]
mediatek: GL-MT6000: Change LED colors
Fine tuning PR: openwrt/openwrt#14355 Ref: 5a82bb909bf1
("mediatek: GL-MT6000: Add missing LED state definitions")
As the only LED is using white in the stock firmware when the device is
running and blue for the bootloader I suggest following changes:
- Using blue for the BL and preinit+failsafe
- White for normal operation (like the original FW) and sysupgrade
With this changes it's clear by looking to the LED in which operation
mode the device is and a possible BL stuck can be seen easily.
Tested with [GL-MT6000](https://openwrt.org/toh/gl.inet/gl-mt6000).
Signed-off-by: Thomas Schröder <tschroeder_github@outlook.com> Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
MAC Address: LAN1 (label) at APPSBL partition
LAN2: label + 1
WLAN2: label + 8
WLAN5: label + 16
Installation
------------
Connect to the RJ45 console (TTL)
Connect LAN1 to host, set host ip as 192.168.1.10
Start a tftp server to serve the initramfs image
Open console connection (9600n8)
Connect power through the DC jack
`Hit any key to stop autoboot: 5`: press any key
`Enter G,Q,or H:`: press `K` to access the hidden option
`Enter password:`: `fap22b1!$` to access a limited u-boot console
`(FAP) #`: `tftpboot your_initramfs_image_name.itb`
`(FAP) #`: `bootm`
Once OpenWrt has booted, install the firmware through sysupgrade
a-gave [Thu, 11 Jan 2024 10:33:21 +0000 (11:33 +0100)]
imagebuilder: copy from buildroot only target/linux/generic and target/linux/<target> to reduce the size
This reduces the size of a single imagebuilder by about 40MB
In example for the target ath79 it would be the sum of generic and <target> directories, so about 16MB,
instead of the whole size of the target directory, about 53MB:
11M target/linux/generic/
3.9M target/linux/ath79/
base-files: add support for rootfs mount options from cmdline
Add support for configuring rootfs mount options from cmdline.
Rootfs mount options can be passed by declaring in the kernel
cmdline as much options as needed prefixed with "rootfs_mount_options."
An example usage is with rootfs with F2FS filesystem to enable
compress_algorithm to reduce flash wear by compressing the files before
writing to flash.
Example usage:
"... rootfs_mount_options.compress_algorithm=zstd ..."
To pass multiple options:
"... rootfs_mount_options.compress_algorithm=zstd rootfs_mount_options.noinline_data ..."
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
97bacb70138a libfstools: query drivers by priority 41e619ed1352 block: recognize /dev/fit* block devices bc3b8cdd3de3 libfstools: add uImage.FIT fitblk driver 846302d09246 libfstools: partname: raise priority to 25 1a5695925ecf mount_root: add support for passing args to mount_root start 1858a492c300 mount_root: permit to pass mount options for rootfs mount
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Chukun Pan [Wed, 20 Dec 2023 15:15:31 +0000 (23:15 +0800)]
mediatek: Cudy WR3000: simplify mac address setup
The mac address of the network port under the switch is
the same as the corresponding gmac by default, so there
is no need to repeat the setting. Compile test only.
Jacob Potter [Sun, 24 Dec 2023 02:37:54 +0000 (21:37 -0500)]
realtek: rtl838x: add Netgear GS110TUP v1 support
The GS110TUP v1 is a managed switch similar to the GS110TPP v1, but with
port 10 as SFP instead of RJ-45 and a total budget of 240 watts. Ports
1-4 support 60-watt 802.3bt PoE and ports 5-8 support 30-watt 802.3at.
The flash layout of the two switches are identical, and the U-Boot
configurations are the same except for having a different magic number,
so installation can be done via the same U-Boot method.
The following command will be needed to enable the port LEDs as per
https://forum.openwrt.org/t/72510/51 :
fw_setenv bootcmd "rtk network on; boota"
Additionally, port 9 (1000base-T from a separate QSGMII PHY) does not
function without this. Port 10 was not tested as no SFP module was
available.
Signed-off-by: Jacob Potter <jacob@j4cbo.com>
[rebase on merged flash layout] Signed-off-by: Sander Vanheule <sander@svanheule.net>
This reverts commit b7f9742da82fa9b122e8d63e48a9a5c0dec298f2.
There are several reports of regressions with this commit. Will be added
back once I've figured out and fixed the cause
Felix Fietkau [Sun, 22 Oct 2023 16:00:08 +0000 (18:00 +0200)]
mac80211.sh: fix deadlock on configuring multiple PHYs simultaneously
When hitting a timing window where ubus configuration calls are hitting hostapd
and wpa_supplicant simultaneously, they can deadlock waiting for each other.
Fix this by using a lock around the ubus calls.
David Bauer [Tue, 9 Jan 2024 19:52:56 +0000 (20:52 +0100)]
ath79: read back reset register
Read back the reset register in order to flush the cache. This fixes
spurious reboot hangs on TP-Link TL-WDR3600 and TL-WDR4300 with Zentel
DRAM chips.
This issue was fixed in the past, but switching to the reset-driver
specific implementation removed the cache barrier which was previously
implicitly added by reading back the register in question.
Uwe Niethammer [Fri, 10 Nov 2023 01:06:15 +0000 (02:06 +0100)]
uqmi: added timeouts in qmi.sh
Modems which are using qmi do not reply on the 1st sync but they do
on subsequent. Sometimes uqmi is hanging - even when using an early
dummy access to unlock the modem. To always guarantee a proper
initialisation, running or hanging uqmi processes must be stopped
before. All uqmi calls have now a timeout option -t to avoid hanging.
Installation
1. Open web management interface.
2. Go to Settings > System Tools > Firmware upgrade.
3. Select "Browse" and select the OpenWrt image with factory.bin suffix.
4. After selecting "Upgrade" firmware writing process will start.
5. Wait till device reboots, power LED should stay solid when it's fully
booted, then it's ready for configuration through LAN port.
Additional information
With how device manufacturer patrtitioned the flash memory, it's possible
that with default packages set, initial factory.bin image won't be
created. In such case, try to reduce packages amount or use older release
for initial conversion to OpenWrt. Later You can use sysupgrade.bin
image with full set of packages because OpenWrt uses unpartitioned flash
memory space unused by vendor firmware.
Reverting to vendor firmware involves converting firmware using
tplink-safeloader with -z option (can be found in ImageBuilder or SDK)
and forcibly applying converted firmware as sysupgrade.
Known issues
WARNING: after removing casing of the device one is exposed to high
voltage and is in a risk of being electrocuted.
Caution when interfacing whith bootloader, saving its environment either
by issuing "saveenv" or selecting option "1: Load system code to SDRAM
via TFTP." in boot menu, any of those will lead to overwriting part of
kernel. This will lead to need of firmware recovery. The cause of this
issue is bootloader having environment offset on flash at 0x40000,
while kernel starts from 0x20000.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[Wrap long line in DTS] Signed-off-by: Sander Vanheule <sander@svanheule.net>
Rafał Miłecki [Wed, 27 Dec 2023 15:20:45 +0000 (16:20 +0100)]
uhttpd: handle reload after uhttpd-mod-ubus installation using postinst
Use postinst script to reload service instead of uci-defaults hack. It's
possible thanks to recent base-files change that executes postinst after
uci-defaults.
This fixes support for uhttpd customizations. It's possible (again) to
adjust uhttpd config with custom uci-defaults before it gets started.
Cc: Hauke Mehrtens <hauke@hauke-m.de> Fixes: d25d281fd668 ("uhttpd: Reload config after uhttpd-mod-ubus was added")
Ref: b799dd3c705d ("base-files: execute package's "postinst" after executing uci-defaults") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Harshal Gohel [Wed, 3 Jan 2024 15:15:12 +0000 (16:15 +0100)]
rtl83xx: dsa: reset PVID to 1 instead of 0
Before, PVID is reset for all ports and goes out of bounds. Also, PVID
is later changed by dsa configuration by `ip link` and `bridge vlan`
commands, this does not change the CPU port PVID and CPU PVID stays 0.
It does not allow sending packets from OpenWrt to any connected devices
unless default configuration is changed
This change iterates up to and including cpu_port and sets default PVID
to 1. For lan* ports PVID can be configured with `ip link` and `bridge
vlan` commands
Acked-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Harshal Gohel [Wed, 3 Jan 2024 14:53:47 +0000 (15:53 +0100)]
rtl93xx: dsa: Fix 802.1QinQ for trunk ports
Fix incorrect register value being set for VLAN_PORT_FWD
Before, the 0b1111 would be set for the register which means outgoing
packets would receive an extra tag, corresponding to the PVID of the
port.
On untagged ports, this meant outgoing packets with a single tag.
On tagged ports, this meant outgoing QinQ packets, where the inner tag
was either the PVID of the untagged ingress port, or the already
assigned original (single) tag.
Acked-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Harshal Gohel [Tue, 12 Dec 2023 14:48:56 +0000 (15:48 +0100)]
rtl930x: Rework per port LED configuration
Use led_setX to determine number of LEDs per port. Introduce macros to
calculate register value and shift for particular LED in a particular
set.
Problem with previous implementation is that it uses is10G status to
determine leds per port. However with usxgmii, driver sets 10g, 5g and
2.5g so even though there are only 2 leds per port it selects 4 leds per
port
This implementation relies on configured led_set node.
Acked-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Felix Fietkau [Tue, 9 Jan 2024 14:15:08 +0000 (15:15 +0100)]
mediatek: fix BPI-R3 wifi mac address
Setting/clearing bits on the first byte of the mac address causes collisions
when using multiple SSIDs on both PHYs. Change the allocation to alter the
last byte instead.
Felix Fietkau [Thu, 21 Dec 2023 16:29:45 +0000 (17:29 +0100)]
libubox: work around recent macOS linker change
rpath handling seems to be more restrictive now. To deal with this,
link the libubox library from STAGING_DIR_HOST to STAGING_DIR_HOSTPKG, so that
packages installed to STAGING_DIR_HOSTPKG can pick it up. This mainly affects
ucode, but possibly other host builds as well
I was able to SSH into the stock firmware of my device.
1. Attach the router to the network
2. Use scp (-O) to copy the sysupgrade image
3. Connect using SSH and run `sysupgrade -n`
Option #2 - U-Boot
One way to use the bootloader for flashing is using TFTP:
1. Connect to the router using an ethernet cable
2 Spin up a TFTP server serving the sysupgrade file
3. Open the case and attach a UART
4. Attach power to the router and interrupt the countdown by pressing
any key
5. Select option #2 (Upgrade firmware)
6. Enter IP address information and image name
7. Wait patiently
Co-Authored-By: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net> Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Hannu Nyman [Sat, 6 Jan 2024 17:59:13 +0000 (19:59 +0200)]
mediatek: GL-MT6000: Add missing LED state definitions
Adjust LED names and provide the OpenWrt status indicator aliases
to actually use LEDs by the OpenWrt boot & sysupgrade processes.
* Name both LEDs clearly by the color
* Add the missing OpenWrt LED status indicator aliases and
remove the now unnecessary default status from blue LED
After this commit, the LEDs are used as:
* bootloader, really early Linux boot: blue LED is on
* preinit/failsafe: white LED blinks rapidly
* late boot: white LED blinks slowly
* boot completed, running normally: blue LED is on
Paul Spooren [Sat, 6 Jan 2024 17:50:00 +0000 (18:50 +0100)]
packages: add PKG_URL variable
Using PKG_URL one may set the URL for all sub packages, which is usually
shared anyway. Future packages should only use PKG_URL instead of adding
it per sub-package.
Paul Spooren [Sat, 6 Jan 2024 17:48:46 +0000 (18:48 +0100)]
packages: store URL in Manifest
The manifest should provide as much information as possible about the
package, including the project URL. With this commit the URL is stored
as it's own attribute instead of at the end of the description.
Antennas
--------
The device features internal antennas as well as external antenna
connectors. By default, the internal antennas are used.
Two GPIOs are exported by name, which can be used to control the
antenna-path mux. Writing a logical 0 enables the external antenna
connectors.
Installation
------------
1. Download the OpenWrt sysupgrade image to the device. You can use scp
for this task. The default username and password are "ubnt" and the
device is reachable at 192.168.1.20.
David Bauer [Thu, 30 Nov 2023 06:32:52 +0000 (07:32 +0100)]
mac80211: avoid crashing on invalid band info
Frequent crashes have been observed on MT7916 based platforms. While the
root of these crashes are currently unknown, they happen when decoding
rate information of connected STAs in AP mode. The rate-information is
associated with a band which is not available on the PHY.
Check for this condition in order to avoid crashing the whole system.
This patch should be removed once the roout cause has been found and
fixed.
Chuanhong Guo [Sun, 7 Jan 2024 15:56:05 +0000 (23:56 +0800)]
kernel: copy only *.ko for debug info
Previous commits installed non-elf files into /lib/modules/$VER/.
COLLECT_KERNEL_DEBUG tries to strip all files and these two files
break the build.
Fix it by copying only kernel modules for debug info collection.
Fixes: e1d8e57614 ("kernel: include modinfo for built-in modules") Fixes: 29f6da4340 ("kernel: include built-in module list") Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Mikhail Zhilkin [Sun, 3 Dec 2023 12:40:46 +0000 (12:40 +0000)]
ramips: update leds & buttons dts description
This commit:
1. Removes deprecated "label" property from the dts leds subnnodes;
2. Updates buttons and leds dts description according to kernel docs
examples.
Lech Perczak [Sat, 18 Nov 2023 15:54:59 +0000 (16:54 +0100)]
ath79: support MikroTik RouterBOARD 911G-5HPacD
The MikroTik RouterBOARD 911G-5HPacD is a stripped-down version of
RB921GS-5HPacD, removing the SFP cage.
This ports the board from ar71xx, and is based on support for
RB921GS-5HPacD.
Disable mdio1 and eth1 nodes in routerboard-92x.dtsi, then re-enable
them in devices using that, so the newly-added device has the port
disabled properly.
See https://mikrotik.com/product/RB911G-5HPacD for more info.
Hardware:
* SoC: Atheros AR9342,
* RAM: DDR 64MB,
* SPI NOR: 64KB,
* NAND: 128MB,
* Ethernet: x1 10/100/1000 port with passive POE in,
* Wi-Fi: 802.11 a/b/g/n (depending on band variant)
* LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED,
Ethernet phy LED,
* Button,
* Beeper.
Flashing:
* Use the RouterBOARD Reset button to enable TFTP netboot,
boot kernel and initramfs and then perform sysupgrade.
* From ar71xx OpenWrt firmware run:
$ sysupgrade -F /tmp/<sysupgrade.bin>
For more info see: https://openwrt.org/toh/mikrotik/common.
Lech Perczak [Sat, 18 Nov 2023 15:53:20 +0000 (16:53 +0100)]
ath79: mikrotik: add RB912UAG-5HPnD as alternative name
Image for RB912UAG-2HPnD supports the 5GHz variant without
modifications. Add it as alternative name, so it can be found easier.
While at that, adjust board display name in device tree, to reflect
that.
Shiji Yang [Sat, 30 Dec 2023 11:52:18 +0000 (19:52 +0800)]
ramips: add missing syscon compatible strings for MT7688 and RT3052
MT7688 devices use the "mt7628an.dtsi" as the template. And RT3052
devices use the "rt3050.dtsi" as template. Therefore, we need to add
the corresponding system controller compatible strings to make them
work properly.
Fixes: 1f818b09f8ae ("ramips: add proper system clock and reset driver support for legacy SoCs") Fixes: #14305 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Tony Ambardar [Sat, 6 Jan 2024 17:26:33 +0000 (09:26 -0800)]
build: fix toplevel check target
Partially revert changes to verbose logging that break the 'check' target
dependencies and trigger many runtime warnings like:
/home/kodidev/openwrt-project/include/toplevel.mk:213: *** mixed implicit and normal rules: deprecated syntax
Fixes: e4a43cda0 ("build: allow var.% targets to bypass the prepare steps") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Samir Ibradžić [Mon, 1 Jan 2024 07:23:09 +0000 (16:23 +0900)]
qualcommax: Fix Buffalo WXR-5950AX12 wifi MAC
Currently, WiFi interfaces on WXR-5950AX12 / WXR-6000AX12 devices
come up with some MAC addresses inconsistent with vendor and Ethernet
addresses. This adds a hotplug override in order to make it consistent
with what is in u-boot env as well as OAM firmware where 1st radio MAC
is set at Ethernet MAC + 8, and 2nd radio mac at Ethernet MAC + 16.
1. Get ssh access. Supported stock firmware **1.0.47**
```
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20set%20ssh_en%3D1%0A"
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20commit%0A"
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Ased%20-i%20's%2Fchannel%3D.*%2Fchannel%3D%22debug%22%2Fg'%20%2Fetc%2Finit.d%2Fdropbear%0A"
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A"
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=********/api/misystem/arn_switch" -d "open=1&model=1&level=%0Apasswd%20-d%20root%0A
```
2. Backup stock partitions
```
nanddump -f /tmp/BL2.bin /dev/mtd1
nanddump -f /tmp/Nvram.bin /dev/mtd2
nanddump -f /tmp/Bdata.bin /dev/mtd3
nanddump -f /tmp/Factory.bin /dev/mtd4
nanddump -f /tmp/FIP.bin /dev/mtd5
nanddump -f /tmp/ubi.bin /dev/mtd8
nanddump -f /tmp/KF.bin /dev/mtd12
```
Then transfer them to your computer in a safe place.
3. Get firmware information `cat /proc/cmdline`
4. Copy openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi to **/tmp** and flash
If **firmware=0**
```
ubiformat /dev/mtd9 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
reboot
```
If **firmware=1**
```
ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
reboot
```
Then reboot your router, it should boot to the OpenWrt initramfs system now.
4. Flash stock images from backup
```
mtd write /tmp/BL2.bin BL2
mtd write /tmp/FIP.bin FIP
mtd write /tmp/ubi.bin ubi
```
Then reboot your router, waiting it finished rollback in minutes.
`ubiformat /dev/mtd7 -y -f /tmp/ubi.bin`
Then reboot your router, waiting it finished rollback in minutes.
Tony Ambardar [Mon, 4 Dec 2023 11:09:28 +0000 (03:09 -0800)]
kernel: include built-in module list
Add modules.builtin to the kernel package for improved handling of loadable
and builtin modules. As with other distros, this allows 'modprobe <module>'
to consistently return success for both loaded/built-in modules, a useful
feature for presence-testing.
Given OpenWrt's few built-in modules, this change and related kmodloader
support add ~1 KB to the compressed image size.
Using sch_fq_codel (builtin) and sch_cake (loadable) for example:
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition
fw_printenv -n boot_part
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel
Replace (X) with your model version either 1 or 2
Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
Shiji Yang [Tue, 12 Dec 2023 05:18:45 +0000 (05:18 +0000)]
ramips: reset mt7620 ethernet phy via reset controller
Use reset controller to reset mt7620 ethernet phy instead of directly
writing system control registers. The reset line of "ephy" is 24, so
the DTS resets properties have been updated to get the correct reset
signal.
Currently OpenWRT does not know how to properly reset the network switch. This would result in
a switch that seemed to come up properly but was unable to handle any traffic. Presumably something
earlier in the boot chain is configuring a part of the switch that gets wiped out when its reset.
For now comment out the reset GPIO entry in the device tree until the driver better supports
bringing up the switch after a reset.
Signed-off-by: Michael 'ASAP' Weinrich <michael@a5ap.net>
Michael Pratt [Wed, 18 May 2022 03:06:36 +0000 (23:06 -0400)]
verbose.mk: fallback to standard file descriptors
In order to pass a status message at runtime,
which is usually listing subtargets
of a Makefile target or an error message,
from a child invocation of Make (submake)
through the parent process to the terminal,
the file descriptors 8 and 9 are opened to be used
by the functions MESSAGE and ERROR_MESSAGE.
However, there are situations where those functions
can be called while not in a submake or a subshell
or a child process which results in a shell error:
/bin/bash: 8: Bad file descriptor
Commit aee3594ffcb72ae3e18c3719012d52519ee2d160
("verbose.mk: print ERROR messages in non-verbose")
has exposed this issue to more cases, but it is not the root cause.
To solve this, use the exit code of the first printf attempt
to the alternative file descriptors in order to tell whether
the standard file descriptors need to be used instead.
In order to get rid of the "Bad file descriptor" error, stderr is
redirected to null after grouping the two printf alternatives
into one command to combine outputs.
For ERROR_MESSAGE, the real message is redirected to stderr
after redirecting the error from the attempted printing to null.
For MESSAGE, without redirection, the Make function "shell"
will absorb the actual message from stdout and input the value into the Makefile,
therefore the dummy variable "_NULL", previously used merely for causing
a call to the MESSAGE function to trigger without writing target rules,
now has and a real value when defined, so rename it to "_MESSAGE"
as a placeholder for the real message when the output should be stdout.
When "_MESSAGE" has a value, use Make function "info" to
finally bring it from the Makefile to the terminal.
This also fixes what is likely a typo, in that
while file descriptor 9 is meant to redirect to stderr
for use in error messages like in the function ERROR_MESSAGE,
that function has printf redirecting to file descriptor 8 instead.
Fixes: a4c8d4e37 ("build: make the color of the 'configuration out of sync' warning red") Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Fri, 24 Nov 2023 10:10:12 +0000 (05:10 -0500)]
build: ensure silent Make behavior for json scripts
Run the invocation of Make with verbosity in order to
prevent the printing of Makefile level and subtarget status.
e.g. make[3] -C target/linux val.DEFAULT_PACKAGES val.ARCH_PACKAGES
Remove piping of stderr, which is only useful when using
the "communicate" method over the "run" method,
and this script would not be written to handle a captured error anyway.
For error testing, stdout and stderr can be set to a file object
with the open() function like this:
out = open('json_out', 'w')
err = open('json_err', 'w')
Michael Pratt [Tue, 17 May 2022 21:50:23 +0000 (17:50 -0400)]
build: allow var.% targets to bypass the prepare steps
These targets are used to input variable values from the Make
context into other things like python scripts, so log messages
should be silenced and build prerequisites should be skipped.
The same thing is done for the other variable print target "val.%".
While at it, combine identical target rules into one definition.
projects / thirdparty / openwrt.git / log
