Robert Marko [Tue, 5 Mar 2024 19:15:55 +0000 (20:15 +0100)]
kernel: crypto: package SHA3
SHA3 is now required by jitterentropy_rng in kernel 6.6, so lets start
preparing by packaging SHA3 support as its supported in 5.15 and 6.1
kernels as well.
AFAIK, only ARMv8.2 has a crypto extension for SHA3, however I am not aware
of any SoC we support that uses ARMv8.2 ISA so its not enabled currently.
• LEDs:
4 x GPIO-controlled LEDs
- 1 Power LED (orange)
- 1 LAN LED (blue)
- 1 WIFI 5g LED (blue)
- 1 WIFI 2g LED (blue)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An populated serial header is onboard, format is
1.25mm 4p (DF13A-4P-1.25H)
RX/TX is working, bootwait is active, secure boot is not
enabled.
The root password of the stock firmware is unknown,
but failsafe mode can be entered to reset the password.
Installation Instructions:
- obtain serial access
- stop auto boot (press "4", Entr boot command line
interface)
- setenv active_fw 0 (to boot from the primary rootfs,
or set to 1 to boot from the secondary rootfs
partition)
- saveenv
- tftpboot the initramfs image
- bootm
- copy
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
to the device
- write the image to the NAND:
- cat /proc/mtd and look for rootfs partition (should
be mtd11,
or mtd12 if you choose active_fw 1)
- ubiformat /dev/mtd11 -f -y
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
- reboot
Note: the firmware is senao-based. But I was unable to build
a valid senao-header into the image.
Maybe they changed the header format and senaoFW isn't
working any more.
1. Acknowledgement to @heheb and @DragonBluep. Upstream commit for ref: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.80&id=9c5662e95a8dcc232c3ef4deb21033badcd260f6
build: do not depend on $(STAGING_DIR)/.prepared when in SDK
The dependency can't be satisfied when building using the SDK, breaking
package builds. As the staging and bin dirs are distributed with the SDK
archive, ignoring the dependency is fine when SDK is set.
BCM63xx maintainance is a PITA since there's no full Device Tree support and
therefore every board needs it's own definition in board_bcm963xx.c
There's no DSA support for this board and there have been very few
contributions in the last years.
Moreover, BCM63xx SoCs >= BCM6358 are already supported in bmips target, so
any efforts to keep this target alive aren't worth the time.
Let's focus the community efforts on improving bmips instead.
Jo-Philipp Wich [Mon, 4 Mar 2024 13:50:46 +0000 (14:50 +0100)]
base-files: sysupgrade: fix streaming backup archives to stdout
Due to previous refactoring in sysupgrade, writing backup archives to
stdout became impossible since the hardcoded gzip output redirection
did not account for the `-` special case filename.
Fix this issue by substituting `-` with `/proc/self/fd/1` in the tar
archive output path variable.
Also remove a redundant `rm -f` of the target file path that occurs
before the file could've possibly been written.
Fixes: #14773 Fixes: https://github.com/openwrt/luci/issues/6961 Fixes: e36cc53092 ("base-files: sysupgrade: use tar helper to include installed_packages.txt") Signed-off-by: Jo-Philipp Wich <jo@mein.io>
build: add $(STAGING_DIR) and $(BIN_DIR) preparation to target and package subdir compile dependencies
In a pristine build, these directories are created as dependencies of
the tools subdir compile, however this step never runs when the tools
compile stamp already exists. Since commit ed6ba2801c0a ("tools: keep
stamp file in $(STAGING_DIR_HOST)"), this will happen after `make clean`:
$(STAGING_DIR) has been deleted, but the tools stamp still exists, so
the next build will fail because $(STAGING_DIR) has not been set up
correctly.
Fix builds after `make clean` by adding the preparation as dependencies
for the target and package directories as well.
Daniel Golle [Sun, 3 Mar 2024 15:22:54 +0000 (15:22 +0000)]
kernel: lantiq: ltq-vmmc: introduce user group for vmmc
asterisk-chan-lantiq is by now the only user of the VMMC interface.
And asterisk runs as user 'asterisk' which doesn't give it permission
to open the /dev/vmmc* devices.
Introduce a new user group 'vmmc' and give permission to access the
/dev/vmmc* devices to that group.
Another commit for asterisk-chan-lantiq will add the 'asterisk' user
to that group.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tobias Schramm [Mon, 26 Feb 2024 11:47:29 +0000 (12:47 +0100)]
mvebu: add support for SolidRun ClearFog Pro
The SolidRun ClearFog Pro is a router based on the SolidRun CN9130 SOM.
Specs:
- SoC: Quad-Core Cortex-A72 CN9130 SoC
- RAM: 4GiB DDR4
- Serial: Micro-USB port on front (FT232R, 115200 8n1)
- Storage: 8GiB eMMC, microSD card slot, 8MiB SPI NOR flash
- Ethernet: 7x GbE (1 port dedicated on SoC, 6 port switch with single GbE CPU port)
- SFP: 1x SFP+
- USB: 1x USB-A 3.1 Gen 1
- PCIe: 2x mini PCIe (one slot with USB and SIM card socket)
- SATA: 1x M.2 Key-B
In addition to the usual connectivity options this device also features
an internal mikroBUS expansion connector.
SATA is currently untested due to lack of a suitable M.2 SSD.
Installation
============
1. Write sdcard sysupgrade image to microSD card using dd or similar
2. Insert microSD card into router and apply power
3. Device boots into OpenWRT
4. (optional) dd sysupgrade image to /dev/mmcblk0 to install to eMMC
Tobias Schramm [Mon, 26 Feb 2024 09:40:50 +0000 (10:40 +0100)]
kernel: 6.1: backport Marvell Armada 8k AP807 cpufreq support
Upstream a patch adding support for cpufreq on AP807-based SoC like the
CN913x was submitted. Include it in patches to ensure best performance
under load and lowest power consumption in idle.
Tianling Shen [Sun, 25 Feb 2024 12:33:08 +0000 (20:33 +0800)]
u-boot.mk: override default PATH to avoid pick hostpkg python
hostpkg python from packages feed can be picked when do a incremental
build because hostpkg has higher priority in PATH. It may lead build
faliure as it's heavily trimmed (e.g. lacks necessary modules).
For uboot which uses binman and intree dtc, this is forced as hostpkg
python will never provide those modules by default.
INAGAKI Hiroshi [Thu, 22 Feb 2024 10:00:57 +0000 (19:00 +0900)]
ath79: add support for ELECOM WAB-I1750-PS
ELECOM WAB-I1750-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 3T3R
- 2.4 GHz : Qualcomm Atheros QCA9558 (SoC)
- 5 GHz : Qualcomm Atheros QCA9880
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 2x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- "SERIAL" : RS232C (+-12V)
- port : ?
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- settings : 115200n8
- note : compatible with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1.04 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.26 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-I1750-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- "SERIAL" port is provided by HS UART on QCA9558 SoC that has
compatibility with qca,ar9330-uart, but QCA955x SoC's is not supported
on Linux Kernel and OpenWrt.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
INAGAKI Hiroshi [Thu, 22 Feb 2024 10:00:57 +0000 (19:00 +0900)]
ath79: add support for ELECOM WAB-S1167-PS
ELECOM WAB-S1167-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9557.
Specification:
- SoC : Qualcomm Atheros QCA9557
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm Atheros QCA9557 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 1x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-S1167-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- The same PCB is used with WAB-S600-PS.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
INAGAKI Hiroshi [Thu, 22 Feb 2024 10:00:57 +0000 (19:00 +0900)]
ath79: add support for ELECOM WAB-S600-PS
ELECOM WAB-S600-PS is a 2.4/5 GHz band 11n (Wi-Fi 4) access point, based
on QCA9557.
This device also supports 11ac (Wi-Fi 5) with the another official
firmware.
Specification:
- SoC : Qualcomm Atheros QCA9557
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm Atheros QCA9557 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 1x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-S600-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- The same PCB is used with WAB-S1167-PS.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
[original work of common dtsi part for WAB-I1750-PS] Signed-off-by: Yanase Yuki <dev@zpc.st>
[adding support for WAB-S600-PS] Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tim Harvey [Thu, 2 Mar 2023 22:29:39 +0000 (14:29 -0800)]
octeontx: update default network config
Update the default network configuration for Gateworks Newport boards
such that the left-most front-panel NIC is WAN and any additional are in
LAN bridge:
- gw610x/gw6903; single NIC: eth0
- gw620x/gw630x; two NIC's from left to right are: eth1 eth0
- gw640x; multiple NIC's from left to right: eth4 eth0 eth1 eth2 eth3
apm821xx: MBL DUO-only: enable USB-Storage for boot from USB support
it is possible to boot and run OpenWrt from an image on an USB-Stick
on the MyBook Live DUO. (No, the MyBook Live Single does NOT have an
USB-Port and attempts at enabling it sadly all failed... so far).
To do that:
First, prepare a USB-Stick by writing the raw and uncompressed OpenWRT
factory image for the device onto the stick (i.e.
# gunzip -c openwrt-*wd_mybooklive*-factory.img.gz > /dev/sd$XX).
Then enter the u-boot via an attached TTL/CMOS 3.3V cable adapter and
give the following commands a try in the:
usb start; sata init
ext2load usb 0:1 ${fdt_addr_r} /boot/apollo3g.dtb
ext2load usb 0:1 ${kernel_addr_r} /boot/uImage
setenv bootargs 'root=/dev/sdc2 rw rootfstype=squashfs,ext4 rootdelay=5'
run addtty; bootm ${kernel_addr_r} - ${fdt_addr_r}
Notes:
- booting from USB-Sticks takes a long time! Be prepared to wait a few
minutes. (~3 minutes for 4 MiB /boot/uImage file on a USB 2.0 Stick)
- the bootargs part 'root=/dev/sdX2' depends on how many HDDs/SSDs are
slotted in. (if none: then use sda, if one: sdb. if two: sdc)
- rootdelay is important as the storage on the USB-Sticks do not show
up fast enough. 5 seconds might be excessive though.
- it's possible to concat these commands together in one line and
write it into u-boot's "bootcmd" environment variable and save the
environment to make the device to always boot from USB from then on.
if you have accidentally overridden the 'bootcmd' and want to return
to 'spec' enter the following commands :
Note about the MyBook Live.
The MyBook Live didn't have the encompassing fixed-partitions.
This is needed for the u-boot,env compatible to be read as otherwise
the kernel assumes this is a legacy NOR/NAND node and this binding
is unsupported.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Robert Marko [Fri, 1 Mar 2024 18:51:24 +0000 (19:51 +0100)]
qualcommax: enable DEBUG_BUGVERBOSE
Enable DEBUG_BUGVERBOSE by default on qualcommax as without it once BUG()
is called we will not get any output other than
"------------[ cut here ]------------"
which is not usefull at all, so since we dont have kernel size constraints
lets enable it by default.
The main goal here is to keep this close to upstream.
Changes include:
- allow symbols implied by y to become m
- make 'imply' obey the direct dependency
- allow only 'config', 'comment', and 'if' inside 'choice'
- qconf: make search fully work again on split mode
- qconf: navigate menus on hyperlinks
- remove '---help---' support
- qconf: allow to edit "int", "hex", "string" menus in-place
- qconf: drop Qt4 support
- nconf: fix core dump when searching in empty menu
- nconf: stop endless search loops
- Create links to main menu items in search
- fix segmentation fault in menuconfig search
- nconf: Add search jump feature
- port qconf to work with Qt6 in addition to Qt5
- fix possible buffer overflow
- fix memory leak from range properties
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Daniel Golle [Fri, 1 Mar 2024 00:06:47 +0000 (00:06 +0000)]
mediatek: mt7622: rtl8367c: add casts to fix compiler warnings
Use type casts to prevent compiler warnings which are going to turn
into errors when we switch to Linux 6.6.
In the long run we should try to get rid of this downstream driver
now that RTL8367S is support by the rtl8365mb DSA driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 29 Feb 2024 23:52:56 +0000 (23:52 +0000)]
mediatek: rename or replace accepted patches
Rename kernel patches accepted upstream to indicate at which version
they have been accepted, replacing downstream variants which what was
accepted upstream. Note that some of them are fixes which will
find their way to older kernel versions as well via linux-stable.
No functional changes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Linus Walleij [Fri, 23 Feb 2024 07:23:47 +0000 (08:23 +0100)]
kirkwood: Add Marvell RTC to all machines with nothing else
The Kirkwood SoCs all have an onchip RTC that can hold the time
over e.g. a reboot which will help if no NTP servers are available.
Create a kernel module package for the Marvell RTC, and add it to
all Kirkwood devices that do not have their own discrete
battery-backed RTC. Adding it to platforms with a proper RTC
is just surplus.
All Kirkwoods have at least one RTC so add RTC to the features
list for Kirkwood as well.
OEM:
root@RE3000:~# ifconfig |grep HWaddr
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 (label)
br-wan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra2 Link encap:Ethernet HWaddr 82:XX:XX:28:XX:X0
rax0 Link encap:Ethernet HWaddr 82:XX:XX:38:XX:X0
rax2 Link encap:Ethernet HWaddr 82:XX:XX:58:XX:X0
OpenWrt
root@OpenWrt:/# ifconfig |grep HW
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy0-ap0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy1-ap0 Link encap:Ethernet HWaddr 82:XX:XX:08:XX:X1
tftp Installation via u-boot:
Connect TTL3.3V converter
connector is under the radiator Set speed 115200 8 N 1
Interrupt boot process by holding down-arrow key during boot then
>> 6. Load image
>> 0 - TFTP client (Default)
enter IP adresses and initramfs-kernel.bin
write to flash via sysupgrade or gui
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Zoltan HERPAI [Wed, 7 Jun 2023 09:54:34 +0000 (11:54 +0200)]
opensbi: allow building on upcoming d1 target
U-boot on D1 also uses OpenSBI as its payload. As the current version of
OpenSBI already supports D1 with no further patches required, allow
building it on the upcoming TARGET_d1 too.
Rafał Miłecki [Wed, 28 Feb 2024 10:51:01 +0000 (11:51 +0100)]
base-files: sysupgrade: use tar helper to include installed_packages.txt
Replace mount + overlay with manually built tar archive that gets
prepended to the actual config files backup. This allows more
flexibility with including extra backup files. They can be included at
any paths and don't require writing to flash or mounting an overlay
which has its own limitations (mount points).
Felix Fietkau [Wed, 28 Feb 2024 08:52:08 +0000 (09:52 +0100)]
mediatek: re-enable mt7622-rfb1-ubi with changed partition layout
The boot loader does not have a fixed size limit for the kernel,
so we're free to change the layout. This may break sysupgrade, but a fresh
flash from initramfs works.
Fixes: 6e2962d4c548 ("mediatek: mt7622: skip build for MT7622 rfb1 (UBI)") Signed-off-by: Felix Fietkau <nbd@nbd.name>
Install instructions:
Detailed instructions can be found on the wiki https://openwrt.org/toh/arcadyan/vrv9510kwac23
1. Boot into UART mode and upload the the https://raw.githubusercontent.com/danielhuici/arcadyan-vrv9510kwac23-utils/main/u-boot.asc file via serial console to boot into U-Boot.
2. Perform a backup of the NAND
3. Setup a TFTP server and serve the https://github.com/danielhuici/arcadyan-vrv9510kwac23-utils/raw/main/u-boot.ltq.lzo.nandspl. Replace the OEM bootloader with this one. Erase your NAND and write the image into it
4. Reboot the router
5. Serve the OpenWrt ramdisk image on your TFTP server and boot it via U-Boot
6. When OpenWrt boots, flash the SquashFS OpenWrt image using LuCi interface, so OpenWrt gets installed into the NAND
Signed-off-by: Daniel Huici <danielhuici@hotmail.com>
This patch avoids learning non-unicast targets in the vxlan FDB. They
are non-unicast and thus should be sent to the broadcast-IPv6 instead of
a unicast address
The following kernel module package was added to the build recipe for the
Turris Omnia: kmod-mt7915-firmware
This module enables support for the official Wi-Fi 6 upgrade kit sold by
CZ.NIC, which includes the AW7915-NP1 miniPCIE board based on Mediatek
MT7915AN, providing 5 GHz Wi-Fi 6 connectivity. With this commit we now
support the latest Turris Omnia Wi-Fi 6 Edition
Signed-off-by: Jan Jasper de Kroon <jajadekroon@gmail.com>
Oskari Rauta [Wed, 14 Feb 2024 04:38:49 +0000 (06:38 +0200)]
e2fsprogs: add libe2p and development headers
this patch separates libe2p from e2fsprogs package, like all other
provided libraries are their own packages. Also some development headers
were missing so I added those along with pkg-config files.
mvebu: fill additional info for mvneta tx queue workaround patch
Because some still unresolved bugs in this driver, which sprout
occasional questions what this patch works around, point to the issue
which started this. Being here, fill headers required by git am.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Daniel Golle [Mon, 26 Feb 2024 03:56:36 +0000 (03:56 +0000)]
base-files: export whole disk of fitblk backing partition
After commit ad62247800 ("base-files: improve lib/upgrade/common.sh")
behavior of export_bootdevice has been made consistent in such way that
always the whole disk device is exported (as that was the case already
when matching via UUID) rather than the partition device.
Do the same for the device holding the fitblk backing partition.
Fixes: 5992f976b3 ("base-files: recognize bootdevice on devices using fitblk") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 26 Feb 2024 01:50:50 +0000 (01:50 +0000)]
mediatek: include 'fitblk' package for subtargets
If selected on a per-board base, fitblk doesn't end up in initramfs
images which always only come with the subtarget's default packages.
Hence fitblk needs to be included as a default package of all
subtargets making use of fitblk instead of it being selected for
individual boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 25 Feb 2024 21:01:01 +0000 (21:01 +0000)]
base-files: recognize bootdevice on devices using fitblk
Boards using the fitblk driver need special treatment when it comes to
detecting the actual block device used to store the image used to boot
from. Transparently handle this in 'export_bootdevice' and provide new
'fitblk_get_bootdev' function to replace implementations in
/lib/upgrade/platform.sh.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 25 Feb 2024 23:56:55 +0000 (23:56 +0000)]
kernel: fix compiler warning caused by NVMEM-on-UBI
When building the UBI NVMEM provider on 32-bit platforms a compiler
warning is triggered due to different sizeof(int).
Fix this by using integer types with well-defined size.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 25 Feb 2024 01:38:39 +0000 (01:38 +0000)]
mediatek: mt7623: bpi-r2: bump compat version on boot
The device booting successfully indicates that bootloader has been
updated. Set compat_version to 1.1 on new configs and bump
compat_version to 1.1 on first boot after a successful sysupgrade.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Flash instructions:
Currently one has to install OpenWrt only via the serial console
1. Rename the factory.bin to to test.bin
2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin
3. connect your device to the LAN port
4. power up the router and press 4 on the console to stop the boot process.
5. enter the following commands on the router console
tftp 0x80060000 test.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[Update leds, add fast-read] Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[Rebuilt version based on mt7620 tplink_archer.dtsi, support for external LNA, remove bad cell count info] Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
From driver point of view no differance between rtl8367b and rtl8367s
if it connected through EXT2 (rgmii only).
So this trivial patch add some identification and initialization only.
SGMII/HSGMII mode for EXT1 is not implemented for the sake of patch
clairity.
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
[Fix code format] Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[add flags to separate chip_num/chip_id detection; drop error print in
rtl8367b_init_regs, drop unnecessary info prints, code style fixes] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[rebase; use MII macros] Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[code optimization] Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Daniel Golle [Sat, 24 Feb 2024 17:00:46 +0000 (17:00 +0000)]
mediatek: mt7623: bpi-r2: set root=/dev/fit0 in bootargs
Set root=/dev/fit0 cmdline parameter as the kernel won't mount rootfs
otherwise after the change from the FIT partition parser to the fitblk
driver which replaces it.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 24 Feb 2024 03:32:13 +0000 (03:32 +0000)]
kernel: fix warning when building fitblk on 32-bit platforms
Kernel warns about comparision of different types without cast when
building the fitblk driver on 32-bit platforms.
Fix this by using `min_t(size_t, ...`.
Daniel Golle [Sat, 24 Feb 2024 03:00:27 +0000 (03:00 +0000)]
mediatek: mt7623: phase out uImage.FIT partition parser
Use the new fitblk driver on the BananaPi R2 as well as UniElec U7623.
Introduce boot device selection for fitblk's /chosen/rootdisk
handle, similar to how it is already done on MT7622, MT7986 and MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 24 Feb 2024 03:00:46 +0000 (03:00 +0000)]
uboot-mediatek: fix truncated patch
The default environment for the Linksys E8450 and Belkin RT3200 got
truncated by one line due to a broken patch. While the impact was
luckily only cosmetic, fix it so bootmenu title also shows U-Boot
version again.
Fixes: 6aec3c7b5b ("mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI build") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
WiFi class AC2200:
- radio0 : 5G on QCA9888 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps , 80MHz - limited for low channels
- radio1: 2,4G on IPQ4019 ,WiFi4- 802.11b/g/n MIMO2x2 300Mbps 40Mhz
- radio2: 5G on IPQ4019 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps ,80Mhz - limited for high channels (from 100 up to 165) . Becouse of DFS remember to set country before turning on.
Ethernet: 2x1GbE (WAN/LAN1, LAN2)
LEDs: section power : green and red , section on top (orbi) drived by TLC59208F: red, green ,blue and white
USB ports: No
Buttons: 2 Reset and SYNC(WPS)
Power: 12 VDC, 2,5 A
Connector type: Barrel
OpenWRT Installation
1. Simplest way is just do upgrade from webpage with *factory.img
2. You can also do it with standard tool for Netgear's debricking - NMPRFlash
3. Most advanced way is to open device , connect to UART console and :
- Prepare OpenWrt initramfs image in TFTP server root (server IP 192.168.1.10)
- Connect serial console (115200,8n1) to UART connector
- Connect TFTP server to RJ-45 port
- Stop in u-Boot and run u-Boot command:
- Login via ssh
- upload or download *sysupgrade.bin ( like wget ... or scp transfer)
- Install image via "sysupgrade -n" (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-netgear_lbr20-squashfs-sysupgrade.bin”)
Back to Stock
- Download firmware from official Netgear's webpage , it will be *.img file after decompressing.
- Use NMRPFlash tool ( detailed insructions on project page https://github.com/jclehner/nmrpflash )
Open the case
- Unscrew nuts and remove washers from antenna's conectors.
- There are two Torx T10 screws under the label next to antenna conectors. You have to unglue this label from left and right corner to get it
- Two parts of shell covers will slide out from eachother , you have to unglue two small rubber pads and namplate sticker on bottom to do that.
- PCB is screwed with 4Pcs of Torx T10 screws
- Before lifting up PCB remove pigtiles for LTE antennas and release them from PCB and radiator (black and white wires)
- On other side of PCB ,in left bottom corner there is already soldered with 4 pins UART connector for console. Counting from left it is +3,3V , TX , RX ,GND (reffer to this picture: https://i.ibb.co/Pmrf9KB/20240116-103524.jpg )
BDF's files are in firmware_qca-wireless https://github.com/openwrt/firmware_qca-wireless/ and in parallel sent to ath10k@lists.infradead.org.
ipq806x: replace ARM bootloader patch with pending upstream version
Replace ARM bootloader patch with pending upstream version. The patch
got reviewed upstream and tested on a Netgear R7800.
This fix a problem with the ARM decompressor and permits to use
AUTO_ZRELADDR without having to hardcode PHYS_OFFSET as the bootloader
now correctly parse the memory modes in the appended DTB.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Daniel Golle [Thu, 22 Feb 2024 19:13:34 +0000 (19:13 +0000)]
Revert "build: don't drop 'user' flag when using the ImageBuilder"
This reverts commit c42b915af0ea53bc1b65bc72afc9875da08b14d2.
Now that rpcd uses the 'Auto-Installed' field to differentiate between
deliberately and implicitely installed packages we can remove the
hotfix.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 23 Feb 2024 13:43:43 +0000 (13:43 +0000)]
mediatek: mt7622: no longer select FIT_PARTITION
All mt7622 board previously using the FIT partition parser have been
converted to use the fitblk driver: 6aec3c7b5b mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI build 41c053141e mediatek: mt7622: convert unifi6lr-v{1,2,3}-ubootmod to fitblk 208f6c1232 mediatek: mt7622: convert BPi-R64 to all-UBI layout and fitblk
Remove the now no longer needed FIT partition parser from builds for
mt7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
projects / thirdparty / openwrt.git / log
