John Thomson [Wed, 16 Oct 2024 02:51:22 +0000 (12:51 +1000)]
kernel: mtdsplit_minor: accept bootimage filename
RouterBOOT v7 on NOR devices no longer accepts the YAFFS kernel ELF
method of booting. It will accept an NPK image named bootimage.
Adjust mtdsplit_minor to accept this second possible boot file name.
Use the conservative value of 127 for YAFFS max name length (used when
YAFFS compiled with unicode support) vs 255.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> Acked-by: Thibaut VARENE <hacks@slashdirt.org> Link: https://github.com/openwrt/openwrt/pull/16780 Signed-off-by: Robert Marko <robimarko@gmail.com>
John Thomson [Tue, 15 Oct 2024 21:13:25 +0000 (07:13 +1000)]
kernel: mtdsplit_minor: return 0 if not fatal
Introduced with Linux 6.7, in commit: 5c2f7727d437 ("mtd: mtdpart: check for subpartitions parsing result"),
when a parser returns an error, this will be passed up, and
consequently, all parent mtd partitions get torn down.
Adjust the MiNOR mtdsplit driver to only return an error if there is a
critical problem in reading from the mtd device or allocating memory.
Otherwise return 0 to indicate that no partitions were found.
Also add logging to indicate what went wrong.
This mtdsplit parser makes a very limited check of the first YAFFS
header. For example, this will not match expectations when initially booting
an initramfs image with OEM on MTD.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> Acked-by: Thibaut VARENE <hacks@slashdirt.org> Link: https://github.com/openwrt/openwrt/pull/16780 Signed-off-by: Robert Marko <robimarko@gmail.com>
Paul Spooren [Sun, 27 Oct 2024 15:36:33 +0000 (16:36 +0100)]
include/package-pack: drop version from provides
Adding a version to the provides causes it to conflict with other
packages that provides the same package, further details are available
here: https://gitlab.alpinelinux.org/alpine/apk-tools/-/blob/master/doc/apk-package.5.scd#L199
This was intitally done, if I remember correctly, to support depending
on the specific kernel modules. Due to patches to APK, versions
containing hashes work now, too, so this is no longer required.
Only add the version to packages that define an ABI version since other
packages depend against the package name plus ABI version.
While at it, format the now rather complex call.
Fixes: https://github.com/openwrt/openwrt/issues/16795 Signed-off-by: Paul Spooren <mail@aparcar.org>
layerscape: set firmware package to skip installation
Add the '~' prefix to package that needs to skip installation as they
are meta-package just to download and compile firmware package for the
final firmware.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ramips: mt7621: drop kmod-i2c-ralink from ASUS RP-AC56
Drop kmod-i2c-ralink from ASUS RP-AC56 as it was wrongly added. Such
kmod is not supported on mt7621 as i2c is handled by the mediatek driver
and not bay the ralink downstream one.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ipq40xx: drop ipq-wifi-teltonika_rutx from Teltonika RUTX50
Drop ipq-wifi-teltonika_rutx from Teltonika RUTX50, the board file was
merged upstream but the ipq package was never dropped from
DEVICE_PACKAGES list.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
build: detach apk repository handling from rootfs.mk
To better support imagebuilder declaring --repositories-file on calling
apk macro, detach this and --repository from rootfs.mk macro and move it
to package Makefile and image.mk where they are used to permit a more
generic usage.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
build: permit overwrite PACKAGE_DIR and PACKAGE_DIR_ALL
Permit to overwrite PACKAGE_DIR and PACKAGE_DIR_ALL variables in
rules.mk.
This is to handle a special case with the ImageBuilder where these
variable are overwrite.
The main problem is that any include calling rules.mk again (example
image.mk) will set these variables again dropping the modified value.
To keep the modified value, set the PACKAGE_DIR and PACKAGE_DIR_ALL only
if not already set. This permits the ImageBuilder to use custom
directory instead of the default one defined in rules.mk.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Til Kaiser [Sun, 27 Oct 2024 13:02:14 +0000 (14:02 +0100)]
xdp-tools: fix compilation when bpftool is installed
Currently, xdp-tools doesn't compile on build systems where
bpftool is installed because additional tools and BPF programs
will be compiled then, which results in build errors.
This commit disables the compilation of those bpftool-dependent tools.
realtek: ethernet: Improve SMI polling configuration based on DTS
Although Zyxel XGS1210 devices are not yet officially supported there
are several patches floating around to enable them. This is a very imporant
one because it fixes a SMI misconfiguration. In the known DTS the SFP+
port settings are set as follows.
So these are PHYs linked to an internal SerDes. During initialization
rtl838x_mdio_init() generates smi_bus=0 & smi_addr=27/28 for these ports.
Although this seems like a valid configuration integrated PHYs attached
to an SerDes do not have an SMI bus. Later on the mdio reset wrongly feeds
the SMI registers and as a result the PHYs on SMI bus 0 do not work.
Without patch (loaded with rtk network on & initramfs):
...
mdio_bus mdio-bus: MDIO device at address 0 is missing.
mdio_bus mdio-bus: MDIO device at address 1 is missing.
mdio_bus mdio-bus: MDIO device at address 2 is missing.
mdio_bus mdio-bus: MDIO device at address 3 is missing.
mdio_bus mdio-bus: MDIO device at address 4 is missing.
mdio_bus mdio-bus: MDIO device at address 5 is missing.
mdio_bus mdio-bus: MDIO device at address 6 is missing.
mdio_bus mdio-bus: MDIO device at address 7 is missing.
...
rtl83xx-switch ... : no phy at 0
rtl83xx-switch ... : failed to connect to PHY: -ENODEV
rtl83xx-switch ... : error -19 setting up PHY for tree 0, switch 0, port 0
rtl83xx-switch ... : no phy at 1
rtl83xx-switch ... : failed to connect to PHY: -ENODEV
rtl83xx-switch ... : error -19 setting up PHY for tree 0, switch 0, port 1
...
With patch (loaded with rtk network on & initramfs):
Signed-off-by: Birger Koblitz <git@birger-koblitz.de> Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> Link: https://github.com/openwrt/openwrt/pull/16457 Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently RTL8218D detection works for a range of devices. That can lead to
false positives. E.g. RTL8218B or RTL8214FC are covered by the detection mask
as well. That is wrong. Nail detection down to the real RTL8218D phy id.
Three PHYs share the same identifier. Until now we simply assume
the type depending of the bus address it is attached to. Make it
better and check the chip mode register instead.
The kernel will either detect by id/mask or by match_phy_device().
Remove the unneeded settings.
realtek: dsa: increase RTL839x max phy page to 8191
According to the specs the RTL839x provides up to 8192 phy pages.
Especially the "raw" page 8191 is used for different initialization
tasks. Increase the limit.
Kevin Zhang [Sun, 27 Oct 2024 05:13:05 +0000 (01:13 -0400)]
rockchip: Add support for RK3566 FriendlyElec NanoPi R3S
This commit adds support for the FriendlyElec NanoPi R3S.
CPU: Rockchip RK3566, Quad-core Cortex-A55
RAM: 2GB LPDDR4X
Ethernet: GMAC RTL8211F GbE, PCIe R8111H GbE
USB3.0 Host: Type-A x1
Storage: MicroSD Slot x 1, and optional on-board 32GB eMMC
Debug Serial Port: 3.3V TTL, 3-pin 2.54mm pitch connector, 1500000 bauds
LED: LED x 3
RTC: One low-power RTC, supports backup battery input
Both GbE controllers are working (WAN eth0, LAN eth1).
Appropriate LAN/WAN interface assignments and MAC address generation.
All three LEDs are working.
USB appears to be working and has been tested with mass storage.
Installation - microSD:
-Uncompress the OpenWRT sysupgrade.img.gz
-Write image to microSD card using dd or similar tool
Installation - eMMC:
-Boot from microSD
-Uncompress the OpenWRT sysupgrade.img.gz
-Flash to eMMC : dd if=x.img of=/dev/mmcblk0
-sync
-Remove microSD card
-Reboot
Daniel Golle [Sat, 26 Oct 2024 00:35:29 +0000 (01:35 +0100)]
kernel: add MultiPath TCP diag kernel module
Add INET diag socket monitoring interface module for MultiPath TCP.
It allows using native Linux socket diagnostic tools such as 'ss' for
Multipath TCP connections.
Co-authored-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com> Signed-off-by: sKy King <29267720+sKyissKy@users.noreply.github.com> Link: https://github.com/openwrt/openwrt/pull/12884 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 26 Oct 2024 14:18:50 +0000 (15:18 +0100)]
generic: mtk_wed: fix path of MT7988 WO firmware
commit eee3c695f3 ("linux-firmware: add offloading firmware for MT7988")
added mt7988_wo_{0,1}.bin in the 'mediatek/mt7988' directory while driver
currently expects the files in the 'mediatek' directory.
Import pending patch which changes the path in the driver header now
that the firmware has been added.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Andreas Gnau [Fri, 25 Oct 2024 16:49:48 +0000 (18:49 +0200)]
airoha: Clarify subtarget compatibility
Clarify compatibility of the two subtargets with different SoCs to
reduce confusion. The added SoC names only differ in small details such
as features enabled (PoN vs DSL for example).
Shiji Yang [Wed, 23 Oct 2024 15:09:57 +0000 (23:09 +0800)]
ramips: dts: add the missing interrupt properties for GPIO nodes
The Ralink GPIO driver supports irqchip function. Hence we need to
add "interrupt-parent" and "interrupt-controller" properties to make
sure it works properly. It is worth noting that all GPIO devices
share the same interrupt line.
Shiji Yang [Wed, 23 Oct 2024 13:56:23 +0000 (21:56 +0800)]
ramips: ralink-gpio: use irqchip helpers to register driver
The gpiolib has already introduced a general GPIO irqchip framework
to initialize the GPIO irqchip[1]. This patch will make use of it
to simplify the legacy Ralink GPIO driver codes. This patch also
includes some code readability improvements.
Hauke Mehrtens [Wed, 23 Oct 2024 22:03:13 +0000 (00:03 +0200)]
mbedtls: update to 3.6.2
Fixes the following security problem:
* CVE-2024-49195: Fix a buffer underrun in mbedtls_pk_write_key_der()
when called on an opaque key, MBEDTLS_USE_PSA_CRYPTO is enabled, and
the output buffer is smaller than the actual output. Fix a related
buffer underrun in mbedtls_pk_write_key_pem() when called on an opaque
RSA key, MBEDTLS_USE_PSA_CRYPTO is enabled and MBEDTLS_MPI_MAX_SIZE is
smaller than needed for a 4096-bit RSA key.
Hauke Mehrtens [Mon, 21 Oct 2024 22:02:28 +0000 (00:02 +0200)]
scripts: Add script to reorder kernel config-* files
This script will reorder the content of all config-* files in the target
folder. It will also remove duplicates. It will not remove options
already defined in the generic configuration.
Piotr Dymacz [Mon, 22 Apr 2024 09:01:52 +0000 (11:01 +0200)]
ath79: add support for ALFA Network WiFi CampPro Nano Duo
ALFA Network WiFi CampPro Nano Duo is a dual-radio Wi-Fi signal extender
(router) in USB dongle form-factor (Type-A plug is used only for power),
based on combination of two radio chipsets: Qualcomm QCA9531 (main SOC)
and MediaTek MT7610U (connected over USB 2.0 interface).
Specifications:
- SOC: QCA9531 v2 (650 MHz)
- DRAM: DDR2 128 MiB (Nanya NT5TU64M16HG-AC)
- Flash: 16 MiB SPI NOR (Macronix MX25L12835F)
- Ethernet: 1x 10/100 Mbps Ethernet (QCA9531)
- Wi-Fi: 2x2:2 2.4 GHz Wi-Fi 4 (QCA9531)
1x1:1 2.4/5 GHz Wi-Fi 5 (MT7610U)
- Antenna: 3x RP-SMA (female) antenna connectors
- LED: 1x orange (RJ45, power indicator)
2x green (status + RJ45 activity/link)
1x blue (Wi-Fi 2.4 GHz status)
- Button: 1x button (reset)
- UART: 1x 4-pin, 2.00 mm pitch header on PCB
- Other: external h/w watchdog (EM6324QYSP5B, enabled by default)
GPIO-controlled USB power for MT7610U
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of status LED (indicates network setup), then
keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
The larger switches of the Linksys LGS series (e.g. LGS352C) make
use of NAND. So the vendor firmware uses other commands to upload
an image through the WebUI.
Add the required scripts. With this we can upload an image to all
devices of that series. Independant of NOR or NAND.
MX65 Hardware info:
- CPU: Broadcom BCM58625 Cortex A9 @ 1200Mhz
- RAM: 2 GB (4 x 4Gb SK Hynix H5TC4G83CFR)
- Storage: 1 GB (Micron MT29F8G08ABACA)
- Networking: BCM58625 switch (2x 1GbE ports, used for WAN ports 1 & 2)
2x Qualcomm QCA8337 switches (10x 1GbE ports, used for LAN ports 3-12)
- PSE: Broadcom BCM59111KMLG connected to LAN ports 11 & 12
- USB: 1x USB2.0
- Serial: Internal header
Notes:
- The Meraki provided GPL source are available at [2].
- Wireless capability on the MX64W and MX65W exists in the form of 2x
Broadcom BCM43520KMLG, which is not supported. These devices will work
otherwise as standard MX64 or MX65 devices.
- Early MX64 units use an A0 variant of the BCM958625 SoC which lacks
cache coherency and uses a different "secondary-boot-reg". As a
consequence a different device tree is needed.
- Installation of OpenWrt requires changing u-boot to a custom version.
This is due to the stock u-boot "nand read" command being limited to
load only 2MB, in spite of the bootkernel1 and bootkernel2 partitions
both being 3MB in the stock layout. It is also required to allow
booting via USB, enabling cache coherency and setting up the QCA
switches and Serdes link on the MX65. The modified sources for U-boot
are available for the MX64[3] and MX65[4].
- Initial work on this device used a small bootloader within the OEM
partition scheme. To allow booting of larger kernels, UBI and bootm
support has been added, along with ability to store env variables to
the NAND. The Shmoo and newly created env partitions have been moved
to the extra space available after the nvram data.
- Users who installed the previous non-UBI supporting bootloader will
need to convert to the new one before flashing a compatible image.
These steps are detailed below.
Initial installation steps:
1. Compile or obtain OpenWrt files for the MX64 or MX65, including
u-boot[3][4], initramfs and sysupgrade images.
2. A USB disk with DOS partition scheme and primary FAT partition is
required.
3. If installing onto an MX64, set up a local web server.
4. On the device, boot into diagnostic mode by holding reset when
powering on the device. Continue to hold reset until the orange LED
begins to flash white. On used units the white flash may be difficult
to see.
5. Plug an Ethernet cable into the first LAN port, set the host to
192.168.1.2 and confirm telnet connectivity to 192.168.1.1.
U-boot installation - MX64 Only:
1. Newer fw versions require extra steps to support OpenWrt. To check,
please connect via telnet and run:
`cat /sys/block/mtdblock0/ro`
If the result is 1, your mtd0 is locked will need to perform extra
steps 4 and 5 in this section. If the result is 0 then skip these.
2. Check which SoC is in use by running the following command:
`devmem 0x18000000`
If devmem is not found then try:
`devmem2 0x18000000`
If the output begins with anything between "0x3F00-0x3F03" you will
need to use the A0 release. For any other output, eg "0x3F04" or
higher, use the regular MX64 image.
3 Confirm the size of the device's boot(mtd0) partition. In most
cases it should be 0x100000 or larger. If this is the case, please
proceed to use the uboot_mx64 image. If the reported size is
0x80000, please use the uboot_mx64_small image, then follow the
later guide to change to the larger image.
`cat /proc/mtd`
Example output:
`# cat /proc/mtd
cat /proc/mtd
dev: size erasesize name
mtd0: 0010000000040000 "boot"
mtd1: 0008000000040000 "shmoo"
mtd2: 0030000000040000 "bootkernel1"
mtd3: 0010000000040000 "nvram"
mtd4: 0030000000040000 "bootkernel2"
mtd5: 3f70000000040000 "ubi"
mtd6: 4000000000040000 "all"`
4. Set up a webserver to serve the appropriate uboot_mx64 from the
following location and verify the SHA512:
https://github.com/clayface/U-boot-MX64-20190430_MX64
5. (Only if mtd0 is locked) You will also need the mtd-rw.ko kernel
module to unlock the partition from the same repo. An mtd executable
is also needed to write the mtd block. Place these on the web server
as well.
6. (Only if mtd0 is locked) Use wget to retrieve the files on the MX64:
`wget http://192.168.1.2/mtd-rw.ko`
`insmod mtd-rw.ko i_want_a_brick=1`
and confirm the unlock is set with dmesg
`mtd-rw: mtd0: setting writeable flag`
7. Download the appropriate u-boot image according to step 3. If you
did not need to unlock the mtd0 partition then use dd to write the
file, with caution:
`wget http://192.168.1.2/uboot_mx64`
`dd if=uboot_mx64 of=/dev/mtdblock0`
If you needed to unlock the mtd0 partition using the mtd-rw module,
run these commands instead to install u-boot instead:
`wget http://192.168.1.2/mtd`
`chmod +x mtd`
`wget http://192.168.1.2/uboot_mx64`
`./mtd write uboot_mx64 /dev/mtd0`
8. Once this has successfully completed, power off the device. If you
did not need to install the small u-boot image, proceed to
"OpenWrt Installation". Otherwise proceed to "UBI supporting
bootloader installation".
U-boot installation - MX65 Only:
1. Obtain telnet access to the MX65.
2. Confirm the size of the device's boot(mtd0) partition. In most
cases it should be 0x100000 or larger. If this is the case, please
proceed to use the uboot_mx65 image. If the reported size is
0x80000, please use the uboot_mx65_small image, then follow the
later guide to change to the larger image.
`cat /proc/mtd`
3. Prepare a USB drive formatted to FAT. Download the appropriate
uboot_mx65 to the USB drive from the following location and verify
the SHA512:
https://github.com/clayface/U-boot-MX64-20190430_MX65
3. Once you have telnet access to the MX65, plug in the USB disk and
run the following commands, with caution. The USB disk should
automount but if it does not, you will need to power off and on
again with reset held. Depending on step 2, use the uboot_mx65 or
uboot_mx65_small image accordingly:
`cd /tmp/media/sda1`
`dd if=uboot_mx65 of=/dev/mtdblock0`
4. Once this has successfully completed, power off the device. If you
did not need to install the small u-boot image, proceed to
"OpenWrt Installation". Otherwise proceed to "UBI supporting
bootloader installation".
UBI supporting bootloader installation:
These steps need to be followed if the older u-boot image was
installed, either because the Meraki diagnostic partition scheme used
0x80000 as the mtd0 size, or because you installed the u-boot provided
while OpenWrt support was still under development. If using OpenWrt,
please make a backup before proceeding.
1. Obtain the relevant image from the MX64(A0) or MX65 u-boot repo:
`openwrt-bcm5862x-generic-meraki_XXXX-initramfs-kernel.bin`
2. With the USB drive already inserted, power on the device while
holding the reset button. A white/orange flashing pattern will
occur shortly after power on. Let go of the reset button. The
device is now booting into OpenWrt initramfs stored on the USB
disk.
3. Connect by SSH to 192.168.1.1 and flash the embedded u-boot image,
changing X as appropriate:
`mtd write /root/uboot_mx6X /dev/mtd0`
You do not need to reboot as this image can handle "Kernel-in-UBI"
OpenWrt installation.
4. You can proceed to obtain and flash the appropriate OpenWrt image
at "OpenWrt Installation" Step 3.
5. Reboot will take significantly longer due to Shmoo calibration. In
case the device does not come online after several minute, power-
cycle the device and see if it boots. If you see an orange/white
flashing pattern, this indicates UBI booting was not successful and
you will need to copy a new bcm53xx image to a USB disk before
booting it and attempting to install OpenWrt again - refer to
"OpenWrt Installation" step 1. Do not attempt to reflash u-boot in
this scenario.
OpenWrt Installation:
1. Having obtained an OpenWrt image, please copy the file
`openwrt-bcm53xx-generic-meraki_XXXX-initramfs.bin`
to the base directory of a FAT formatted USB drive using DOS
partition scheme ,where XXXX is mx64, mx64_a0 or mx65 depending on
which device you have.
2. With the USB drive already inserted, power on the device. Boot time
will be longer than usual while Shmoo calibration takes place. A
different white/orange flashing pattern will eventually occur to
indicate device is now booting into OpenWrt initramfs stored on the
USB disk.
3. Ensuring Ethernet is plugged into a LAN port with IP set in the
192.168.1.0/24 subnet excluding 192.168.1.1, use SCP to copy the
sysupgrade file to 192.168.1.1:/tmp, eg:
`scp openwrt-bcm53xx-generic-meraki_XXXX-squashfs.sysupgrade.bin\
192.168.1.1:/tmp`
4. Connect by SSH to 192.168.1.1 and run sysupgrade:
`sysupgrade \
/tmp/openwrt-bcm53xx-generic-meraki_XXXX-squashfs.sysupgrade.bin`
5. OpenWrt should now be installed on the device.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
[ Rebase kernel configuration for 6.6,
fix failsafe by making kmod-eeprom-at24 and kmod-dsa-qca8k built-in,
resolve conflicts,
add LED aliases,
fix eth0 MAC address at probe ]
TODO:
- fix multiple LED colors not applied despite aliases - due to custom
/etc/diag.sh
- fix race condition between preinit and probing of the DSA tree,
causing no network interface available in failsafe mode (in general
case - to allow moving drivers back to modules)
projects / thirdparty / openwrt.git / log
