Kyle Hendry [Sun, 24 Nov 2024 19:29:33 +0000 (11:29 -0800)]
bmips: pinctrl-bcm63268: add gpio function
Right now there's no way to know what state CFE will leave the pinctrl
registers in, so they should be explicitly set by linux on boot. This
patch adds a gpio configuration for drivers that need it, i.e. gpio-leds.
Tony Ambardar [Sun, 8 Dec 2024 03:49:49 +0000 (19:49 -0800)]
bpftool: Update to v7.5.0
Update to the latest upstream release to include recent improvements and
bugfixes, and simplify use of PKG_SOURCE_VERSION.
This version supports BPF objects of either endianness, allowing for
introspection, linking and skeleton creation, and enables cross-compiling
modern BPF applications for targets with non-native byteorder.
Chukun Pan [Fri, 20 Dec 2024 14:30:01 +0000 (22:30 +0800)]
trusted-firmware-a.mk: fix release download URL
The URL of trusted-firmware-a is no longer available for
downloading release:
https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/
curl: (22) The requested URL returned error: 401 Unauthorized
So we switch to the GitHub mirror repository to download.
Antonio Pastor [Fri, 20 Dec 2024 16:28:45 +0000 (11:28 -0500)]
kernel: generic: patch: 802.2+LLC - set transport_header offset
Conversion to DSA broke 802.2+LLC+SNAP packet processing. Frames
received by napi_complete_done with GRO and DSA have transport_header
set two bytes short, or pointing 2 bytes before network_header &
skb->data. As snap_rcv expects transport_header to point to SNAP
header (OID:PID) after LLC processing advances offset over LLC header
(llc_rcv & llc_fixup_skb), code doesn't find a match and packet is
dropped.
Image built at this commit operates properly: 86dadeba48 - generic: add patch for GPON-ONU-34-20BI quirk
Image built at following commit exhibits the issue: 337e36e0ef - ipq806x: convert each device to DSA implementation
As issue is LLC specific, to avoid impacting non-LLC traffic, and to
follow up on original assumption made on kernel commit fda55eca5a33
("net: introduce skb_transport_header_was_set()") stating "network
stacks usually reset the transport header anyway", llc_fixup_skb to
reset and advance the offset. llc_fixup_skb already assumes the LLC
header is at skb->data, and by definition SNAP header immediately
follows.
Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.67..HEAD
(HEAD -> 811ff707533bcd67cdcd368bbd46223082009b12)
Commit 56d97fff55f3 backported leds-ktd202x from upstream but didn't add the
generic config symbol.
Fixes: 56d97fff55f3 ("generic: backport support for KTD2026/7 rgb(w) led controller") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Link: https://github.com/openwrt/openwrt/pull/17396 Signed-off-by: Robert Marko <robimarko@gmail.com>
Joel Low [Fri, 27 Dec 2024 00:13:26 +0000 (08:13 +0800)]
netfilter: fix bogus reference to `kmod-nf-conntrack-timeout`
Fix bogus reference to kmod-nf-conntrack-timeout, fixing the warning
`WARNING: Makefile 'package/kernel/linux/Makefile' has a dependency on
'kmod-nf-conntrack-timeout', which does not exist`.
Fixes: 0e2dcfc4f488 ("netfilter: add kmod-nfnetlink-ct{helper,timeout}") Signed-off-by: Joel Low <joel@joelsplace.sg> Link: https://github.com/openwrt/openwrt/pull/17388 Signed-off-by: Robert Marko <robimarko@gmail.com>
John Audia [Wed, 11 Dec 2024 20:06:30 +0000 (15:06 -0500)]
bcm27xx/bcm2712: add RP1 drivers via kmods
Add kmods for the following RP1 options that not all users
will necessarily need or want compiled in:
* Composite video
* Display video
* LED control
* PWM control
* Serial video
Shiji Yang [Wed, 25 Dec 2024 12:33:23 +0000 (20:33 +0800)]
ramips: mt762{0,8}: reduce default MMC clock to 24 MHz
The upstream mtk-sd driver did not perform specific timing
optimization for MT762x series SoC, hence the SDHC peripheral
of some boards cannot run at too high frequency. Reduce the
maximum clock frequency to fix the mmc read/write error.
Joan Moreau [Sat, 28 Sep 2024 13:53:02 +0000 (13:53 +0000)]
ath79: add support for KuWfi CPE830(D) / YunCore CPE830(D)
Short specification:
* 650/600/216 MHz (CPU/DDR/AHB)
* 2x 10/100 Mbps Ethernet, passive PoE support
* 64 MB of RAM (DDR2)
* 16 MB of FLASH
* 2T2R 2.4 GHz with external PA, up to 30 dBm (1000mW)
* 2x internal 14 dBi antennas
* 8x LED, 1x button
* No UART on PCB on some versions
* Display panel with 2x buttons (F/N) not supported (and not relevant in OpenWrt)-
Flash instructions
* Connect PC with 192.168.0.141 to WAN port
* Install a TFTP server on your PC ('atftp' is doing the job for instance)
* Copy your firmware in the TFTP folder as upgrade.bin
* Power up device pushing the 'reset' button
* The device shall upload upgrade.bin, install it and reboot
* Device shall be booting on 192.168.1.1 as default
Kyle Hendry [Sun, 17 Nov 2024 02:16:31 +0000 (18:16 -0800)]
bmips: dts: fix pinctrl error
The kernel logs the error "bcm6368_nand 10000200.nand: there is not valid
maps for state default" on boot and all nand pins show as UNCLAIMED in
sysfs pinmux-pins.
bcm6362.dtsi, bcm6368.dtsi and bcm63268.dtsi use the undocumented property
group which the driver doesn't understand. This has been documented upstream
in commit caf963efd4b0b9ff42ca12e52b8efe277264d35b.
Replacing group with pins allows the nand pins to be properly configured.
Sander Vanheule [Tue, 24 Dec 2024 08:56:11 +0000 (09:56 +0100)]
realtek: generate compat_version 2.0 for GS1900
The GS1900 images have been updated to have a larger firmware partition,
bumping the compatibility version to 2.0. However, since this version is
generated on first boot and the default was used, these images still
advertised 1.0 after a fresh install.
Add a new uci-defaults script that will generate the correct version for
all affected Zyxel GS1900 devices.
Rosen Penev [Mon, 16 Dec 2024 22:15:08 +0000 (14:15 -0800)]
ath79: fix calibration size for AR9287
These devices use AR9287, which uses 3d8 as the calibration size, not
440 like newer chips do. Add a compatible line to make it clear that
this is the case.
Joel Low [Sat, 14 Dec 2024 13:39:36 +0000 (21:39 +0800)]
netfilter: add kmod-nfnetlink-ct{helper,timeout}
Add kmod-nfnetlink-ct{helper,timeout} to allow handling firewall rules
in userspace (together with conntrackd). The timeout module allows
specifying custom expiration rules.
Roland Reinl [Fri, 13 Dec 2024 17:58:26 +0000 (18:58 +0100)]
mediatek: filogic: Add support for D-Link AQUILA PRO AI M60
Specification:
- MT7986 CPU using 2.4GHz and 5GHz WiFi (both AX)
- MT7531 switch
- 512MB RAM
- 128MB NAND flash (MX35LF1GE4AB-Z4I) with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718 (Same as D-Link M30 A1)
- 3 buttons (WPS, reset, LED on/off)
- 1x 2.5 Gbit WAN port with Maxlinear GPY211C
- 4x 1 Gbit LAN ports
Disassembly:
- There are five screws at the bottom: 2 under the rubber feet, 3 under the label.
- After removing the screws, the white plastic part can be shifted out of the blue part.
- Be careful because the antennas are mounted on the side and the top of the white part.
Serial Interface
- The serial interface can be connected to the 4 pin holes next to/under the antenna cables.
- Note that there is another set of 4 pin holes on the side of the board, it's not used.
- Pins (from front to rear):
- 3.3V (do not connect)
- TX
- RX
- GND
- Settings: 115200, 8N1
MAC addresses:
- MAC address is stored in partition "Odm" at offset 0x81 (for example XX:XX:XX:XX:XX:52)
- MAC address on the device label is ODM + 1 (for example XX:XX:XX:XX:XX:53)
- WAN MAC is the one from the ODM partition (for example XX:XX:XX:XX:XX:52)
- LAN MAC is the one from the ODM partition + 1 (for example XX:XX:XX:XX:XX:53)
- WLAN MAC (2.4 GHz) is the one from the ODM partition + 2 (for example (XX:XX:XX:XX:XX:54)
- WLAN MAC (5 GHz) is the one from the ODM partition + 5 (for example (XX:XX:XX:XX:XX:57)
Flashing via OEM web interface:
- Currently not supported because image crypto is not known
Flashing via recovery web interface:
- This is only working if the first partition is active because recovery images are always flashed to the active partition and OpenWrt can only be executed from the first partition
- Use a Chromium based browser, otherwise firmware upgrade might not work
- Recovery web interface is accessible via 192.168.200.1 after keeping the reset button pressed during start of the device until the LED blinks red
- Upload the recovery image, this will take some time. LED will continue flashing red during the update process
- The after flashing, the recovery web interface redirects to http://192.168.0.1. This can be ignored. OpenWrt is accessible via 192.168.1.1 after flashing
- If the first partition isn't the active partition, OpenWrt will hang during the boot process. In this case:
- Download the recovery image from https://github.com/RolandoMagico/openwrt/releases/tag/M60-Recovery-UBI-Switch (UBI switch image)
- Enable recovery web interface again and load the UBI switch image. This image works on the second partition of the M60
- OpenWrt should boot now as expected. After booting, flash the normal OpenWrt sysupgrade image (for example in the OpenWrt web interface)
- Flashing a sysupgrade image from the UBI switch image will make the first partition the active partition and from now on, default OpenWrt images can be used
Flashing via Initramfs:
- Before switching to OpenWrt, ensure that both partitions contain OEM firmware.
- This can be achieved by re-flashing the same OEM firmware version again via the OEM web interface.
- Flashing via OEM web interface will automatically flash the currently not active partition.
- Open router, connect serial interface
- Start a TFTP server at 192.168.200.2 and provide the initramfs image there
- When starting the router, select "7. Load Image" in U-Boot
- Settings for load address, load method can be kept as they are
- Specify host and router IP address if you use different ones than the default (Router 192.168.200.1, TFTP server 192.168.200.2)
- Enter the file name of the initramfs image
- Confirm "Run loaded data now?" question after loading the image with "Y"
- OpenWrt initramfs will start now
- Before flashing OpenWrt, create a backup of the "ubi" partition. It is required when reverting back to OEM
- Flash sysupgrade image to flash, during flashing the U-Boot variable sw_tryactive will be set to 0
- During next boot, U-Boot tries to boot from the ubi partition. If it fails, it will switch to the ubi1 partition
Reverting back to OEM:
- Boot the initramfs image as described in "Flashing via Initramfs" above
- Copy the backed up ubi partition to /tmp (e.g. by using SCP)
- Write the backup to the UBI partition: mtd write /tmp/OpenWrt.mtd4.ubi.bin /dev/mtd4
- Reboot the device, OEM firmware will start now
MAC Address:
use address(sample 1) source
label cc:e1:d5:xx:xx:ed art@macaddr_wan
lan cc:e1:d5:xx:xx:ec art@macaddr_lan
wan cc:e1:d5:xx:xx:ed $label
WiFi4_2G cc:e1:d5:xx:xx:ec art@cal_ath9k
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.11.10/24
to the ethernet port. Serve the OpenWrt initramfs image as
"openwrt.bin"
3. Boot the initramfs image using U-Boot
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm 0x84000000
4. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Installation from Web Interface
------------
To flash just do a firmware upgrade from the stock firmware (Buffalo
branded dd-wrt) with squashfs-factory.bin
Hauke Mehrtens [Sun, 22 Dec 2024 16:33:21 +0000 (17:33 +0100)]
mbedtls: Deactivate ARIA block cipher by default
The ARIA block cipher is pretty uncommon in TLS, deactivate it for now.
This saves some space and reduces the possible variations and attack
vectors of mbedtls.
ARIA support was deactivated in OpenWrt 23.05 by default.
Tianling Shen [Mon, 23 Dec 2024 13:57:15 +0000 (21:57 +0800)]
uboot-rockchip: fix build with swig 4.3.0
Fixes the following error by backporting upstream update:
```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function ‘_wrap_fdt_next_node’:
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function ‘SWIG_Python_AppendOutput’
5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val);
| ^~~~~~~~~~~~~~~~~~~~~~~~
```
Tianling Shen [Mon, 23 Dec 2024 13:56:31 +0000 (21:56 +0800)]
uboot-rockchip: increase rng-seed size
Increase rng-seed size to make Linux happy and initialize rng pool instantly.
Linux 5.19+ requires 32 bytes of entropy to initialize random pool, but u-boot
currently provides only 8 bytes.
Hauke Mehrtens [Mon, 23 Dec 2024 00:49:04 +0000 (01:49 +0100)]
uboot-d1: Adapt BUILD_DEVICES to renamed boards
The boards where renamed, but BUILD_DEVICES was not adapted. This
variable points to the board name. Without this change the u-boot
binaries are not selected in the configuration.
Copy the u-boot binaries under the BUILD_DEVICES name as it is expected
by the image scripts.
Thomas Richard [Fri, 29 Nov 2024 10:53:14 +0000 (11:53 +0100)]
arm-trusted-firmware-stm32: bump to v2.12
No need to pass the option no-warn-rwx-segments. Since v2.12, TF-A
automatically selects it if needed.
A patch is added to revert commit 03a581e2 ("feat(stm32mp1-fdts): remove
RTC clock configuration").
This commit removed RTC clock configuration, as it assumed that it was done
correctly by OPTEE.
But it is not the case. Without this patch the RTC is in a bad state,
consequently the wifi module cannot be initialized.
stm32_rtc 5c004000.rtc: rtc_ck is slow
stm32_rtc 5c004000.rtc: Can't enter in init mode. Prescaler config failed.
stm32_rtc: probe of 5c004000.rtc failed with error -110
sdio mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.st,stm32mp135f-dk.bin failed with error -2
brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50
Thomas Richard [Thu, 28 Nov 2024 17:05:29 +0000 (18:05 +0100)]
uboot-stm32: bump to 2024.10
Now the tool mkeficapsule is built by default if EFI_LOADER config is set
(which is the case by default for armv7).
This tool needs gnutls, which only exists in the packages feed.
As we don't need mkeficapsule, just disable it.
- The original partition-Ubi partition-Ubi1 is an AB dual system, and Openwrt only uses Ubi. So flash requires modifying the uboot variable `boot_from=ubi` to ensure that it only starts from Ubi.
- The Product and Custom partitions are original and only exist to align with the original layout; they are not used by OpenWrt.
- **USB-to-TTL Serial Adapter** (e.g., CH340 or CP2102).
- **Dupont Wires** (male-to-male, 3 wires).
- **PC/Laptop** with a serial communication tool.
- Screwdriver (to open the router case).
1. **OpenWrt Firmware**:
- Download the appropriate `wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin` firmware file for your router from the [OpenWrt website](https://openwrt.org/).
2. **Serial Communication Tool**:
- Windows: PuTTY, Tera Term.
- Linux/Mac: Minicom, screen.
3. (Optional) **TFTP Server**:
- Install a TFTP server like Tftpd64 or tftp-hpa.
---
1. Open the router casing and locate the **TX, RX, and GND** pins.
2. Connect the router pins to the USB-to-TTL adapter as follows:
- **TX (router)** → **RX (adapter)**
- **RX (router)** → **TX (adapter)**
- **GND (router)** → **GND (adapter)**
3. Do **not** connect the VCC pin to avoid damage.
1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Select Option 0 by typing 0 and pressing Enter.
5. Input into
```plaintext
MT7981> setenv boot_from ubi
MT7981> saveenv
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
MT7981> printenv
baudrate=115200
boot_from=ubi
...
```
the above indicates system will start from *ubi*.
and then type
```plaintext
MT7981> reset
```
will boot from *ubi*
1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Choose Option 3: Upgrade Firmware
Enter Upgrade Mode
Select Option 3 by typing 3 and pressing Enter.
Upgrade Methods
You will be prompted to choose between:
```plaintext
*** Upgrading Firmware ***
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.10
Input IP netmask: 255.255.255.0
Input file name: wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin
```
Type Enter to proceed. The router will erase the old firmware and write the new one.
Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com
Rani Hod [Sun, 22 Dec 2024 00:53:51 +0000 (02:53 +0200)]
linux-firmware: package MediaTek MT7925 Bluetooth firmware
`btusb` fails to start on MT7925 hardware without the appropriate
firmware being loaded first:
```
bluetooth hci0: Direct firmware load for mediatek/mt7925/BT_RAM_CODE_MT7925_1_1_hdr.bin failed with error -2
bluetooth hci0: Falling back to sysfs fallback for: mediatek/mt7925/BT_RAM_CODE_MT7925_1_1_hdr.bin
```
Package firmware for MediaTek MT7925 Bluetooth from `linux-firmware`.
Eric Fahlgren [Tue, 3 Dec 2024 23:17:05 +0000 (15:17 -0800)]
build: d1: add SUPPORTED_DEVICES
Include specific SUPPORTED_DEVICES values derived from the .dts file.
This makes the generated profiles.json consistent with the 'board_name' from
'ubus call system board'.
Specifically, this fixes a bug in the generated profiles.json that breaks the
ASU clients when selecting the proper image from a build.
See the 'supported_devices' fields here for the incorrect (or incomplete) list:
https://downloads.openwrt.org/releases/24.10.0-rc1/targets/d1/generic/profiles.json
Links: https://forum.openwrt.org/t/owut-openwrt-upgrade-tool/200035/287 Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com> Link: https://github.com/openwrt/openwrt/pull/17155 Signed-off-by: Robert Marko <robimarko@gmail.com>
Shymon Samsel [Thu, 19 Dec 2024 17:28:43 +0000 (12:28 -0500)]
ipq-wifi: update to Git HEAD (2024-12-18)
4b849214b137 ipq8074: add TP-Link EAP620 HD v1 BDF Add board file for TP-Link EAP620 HD v1. Sourced from bdwlan_US.bin in stock firmware 1.1.0 Build 20211028
Shymon Samsel [Fri, 13 Dec 2024 10:59:04 +0000 (05:59 -0500)]
ipq807x: add support for TP-Link EAP620 HD v1
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 1.4 GHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCA5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (2x2 2.4 GHz 802.11b/g/n/ax)
* Ethernet: AR8031 (10/100/1000BASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively.
Be sure to crossover TX and RX.
3. Copy RAM firmware
openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
to a TFTP server's root that is in the same subnet as your AP.
4. Power up the AP hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip <TFTP server addr>
# setenv ipaddr <addr of AP>
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Known Issues:
* 5GHz radio instability (upstream current ath11k build bug maybe?)
Device support directly followed from EAP660HDv1 support
Links: #15832
The dual-boot partition layout for the Zyxel GS1900 switches results in
6.9MB for both kernel and rootfs. Depending on the package selection,
this may already leave no space for the user overlay.
Merge the two firmware partitions, effectively dropping dual boot
support with OpenWrt. This results in a firmware partition of 13.9MB,
which should leave some room for the future.
To maintain install capabilites on new devices, an image is required
that still fits inside the original partition. The initramfs is used as
factory install image, so ensure this meets the old size constraints.
The factory image can be flashed via the same procedure as vendor images
when reverting to stock, can be installed from stock, or can be launched
via tftpboot.
Sander Vanheule [Sun, 20 Feb 2022 18:50:38 +0000 (19:50 +0100)]
realtek: ZyXEL GS1900-48: drop gpio-restart
GPIO 5 on the RTL8231 is defined reset the system, but fails to actually
do so. This triggers a kernel a number of warnings and backtrace for
GPIO pins that can sleep, such as the RTL8231's. Two warnings are
emitted by libgpiod, and a third warning by gpio-restart itself after it
fails to restart the system:
[ 106.654008] ------------[ cut here ]------------
[ 106.659240] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 106.826218] ---[ end trace d1de50b401f5a153 ]---
[ 106.962992] ------------[ cut here ]------------
[ 106.968208] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 107.136718] ---[ end trace d1de50b401f5a154 ]---
[ 111.087092] ------------[ cut here ]------------
[ 111.092271] WARNING: CPU: 0 PID: 4279 at drivers/power/reset/gpio-restart.c:46 gpio_restart_notify+0xc0/0xdc
[ Stack dump and call trace ]
[ 111.256629] ---[ end trace d1de50b401f5a155 ]---
By removing gpio-restart from this device, we skip the restart-by-GPIO
attempt and rely only on the watchdog for restarts, which is already the
de facto behaviour.
Lorenz Brun [Fri, 20 Dec 2024 22:37:01 +0000 (23:37 +0100)]
octeon: enable AT803x PHY driver
The AR8035 PHY is used in most Octeon boards supported by OpenWRT (all
the Ubiquiti routers at least). To be able to use its PHY-specific
functionality (cable testing, LED Control, ...) it should be built on
Octeon. It also needs the regulator framework, so enable that as well.
These boards are not space-constrained, so this really has no downsides.
Tested on an EdgeRouter Lite, cable tests now work with ethtool-full.
This backport patch inserted suspend/resume callbacks
for the wrong PHY driver.
The fixed patch is needed for Huawei AP5030DN
to initialize its second PHY.
Refresh all affected patch with make target/linux/refresh.
Fixes: 06cdc07f8cc7 ("ath79: add support for Huawei AP5030DN") Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de> Link: https://github.com/openwrt/openwrt/pull/17312 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Jonas Jelonek [Wed, 13 Nov 2024 22:25:09 +0000 (22:25 +0000)]
mediatek: filogic: bpi-r4: set netdev-name for sfp ports
Sets openwrt,netdev-name for the gmac nodes in the dts of BPI-R4 which
correspond to the two sfp slots. By default they are automatically
named as eth1 and eth2 in bad order, however 'SFP1-WAN' and 'SFP2-LAN'
are printed on the PCB and the official metal case has labels 'SFP-WAN'
and 'SFP-LAN'. Thus, label the ports accordingly to match the
board/case labels.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Jonas Jelonek [Sun, 10 Nov 2024 00:43:23 +0000 (00:43 +0000)]
mediatek: filogic: bpi-r3: set netdev-name for sfp1 port
Sets openwrt,netdev-name for the gmac1 node in the dts of BPI-R3, which
corresponds to the sfp1 slot, to have a proper naming and match the
label on the official BPI-R3 metal case. This renames the port from eth1
to sfp1.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Jonas Jelonek [Mon, 25 Nov 2024 23:04:15 +0000 (23:04 +0000)]
mediatek: filogic: support openwrt,netdev-name for renaming interfaces
Add support in filogic subtarget for our own custom property
`openwrt,netdev-name` in the device tree instead of `label` for
renaming interfaces. This was suggested upstream to avoid potential
conflicts [1].
Rosen Penev [Sun, 16 Jun 2024 19:40:53 +0000 (12:40 -0700)]
ath79: tplink,deco-s4-v2: use nvmem for cal
Userspace handling is deprecated. MAC address stuff needs to remain
handled in userspace as it's encrypted. Maybe an NVMEM driver can be
written in the future...
Felix Fietkau [Wed, 18 Dec 2024 09:35:21 +0000 (10:35 +0100)]
firewall4: update to Git HEAD (2024-12-18)
e00958884416 fw4: do not add physical devices for soft offload dfbcc1cd127c fw4: skip not existing netdev names in flowtable device list 18fc0ead19fa init: use the reload data trigger to reload firewall on procd data changes
Fixes: https://github.com/openwrt/openwrt/issues/13410 Signed-off-by: Felix Fietkau <nbd@nbd.name>
Chukun Pan [Mon, 16 Dec 2024 15:09:26 +0000 (23:09 +0800)]
qualcommax: fix usb regulator supply for RT-AX89X
The qusb_phy node looks for the following supply:
"vdd", "vdda-pll", "vdda-phy-dpdm"
And ssphy node looks for the following supply:
"vdda-phy", "vdda-pll"
So fix the usb regulator supply for RT-AX89X.
Fixes: 1306237 ("qualcommax: use PHY regulator for USB GPIO") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Link: https://github.com/openwrt/openwrt/pull/17290 Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Tue, 17 Dec 2024 20:57:44 +0000 (21:57 +0100)]
unetd: update to Git HEAD (2024-12-17)
93461ca4c827 unet-cli: only apply defaults on create 3e5766783d5d unet-tool: add support for confirming password 074d3659ca4a unet-cli: confirm password when creating new seed based key bf3488a3807a unet-cli: add add/set-local-host command 9eb57c528461 unet-cli: add support for setting interface zone a0a2d80f3459 ubus: add firewall rules for network port/pex_port via procd
Felix Fietkau [Tue, 17 Dec 2024 20:53:36 +0000 (21:53 +0100)]
procd: update to Git HEAD (2024-12-17)
2e206dbe77ec service: add support for triggers on service/instance data changes 735b48728fca service: remove leftover lines from previous commit 32469644a029 service: allow incremental changes to service properties fd01fb852302 service: fix double free bug when dealing with data
Linus Walleij [Sun, 17 Nov 2024 21:47:27 +0000 (22:47 +0100)]
kirkwood: Make the Marvell DSA switch a module
Not all Kirkwood systems have the Marvell MV88E6XXX switches.
Drop those from the generic config and add them as modules
in the systems that have it.
This was inferred by inspecting the upstream DTS files for any
mv88e* strings and adding the mv88e6xxx kmod package to those
that have an upstream device tree with an MV88E6xxx switch
and an OpenWrt image target.
projects / thirdparty / openwrt.git / log
