Chuncheng Chen [Thu, 20 Oct 2022 03:43:11 +0000 (11:43 +0800)]
ramips: add support for ASUS 4G-AX56
Specifications:
- Device: ASUS 4g-AX56
- SoC: MT7621AT
- Flash: 128MB
- RAM: 512MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LTE : Fibocom FG621-EA
- LEDs: 1x POWER (white, configurable)
1x 2.4G (white, not configurable)
1x 5G (white, not configurable)
1x WAN (white, not configurable)
1x 3G/4G (white, not configurable)
3x signal (white, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.0.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.0.1
Input TFTP server's IP address: 192.168.0.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_4g-ax56-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Notice:
- LTE module is disable after flash openwrt image so you must active LTE by following two AT command
echo -e "AT+GTAUTOCONNECT=1\r\n" > /dev/ttyUSB0
echo -e "AT+GTRNDIS=1,1\r\n" > /dev/ttyUSB0
- After finish AT command once, you don't need to input command later even if reboot/restore default
Both 2.4GHZ and 5GHZ are working, it is enabled by default since there is no
physical ethernet port in the device.
All LED's and buttons work.
UART: 57600 8N1 3.3V
Installation
Upload the openwrt-ramips-mt7620-trendnet_tha103ac-initramfs-kernel.bin via
the manufacturer firmware upgrade page on the device.
Upon reboot wait +- 3 mins until the green power LED is not flashing anymore
(do not be tempted to switch the device off while the LED is flashing, unless
you are ready for soldering and TTL) and then press the WPS button to enable
the default OpenWrt Wifi AP, the BLUE wifi LED will start flash.
Then install openwrt-ramips-mt7620-trendnet_tha103ac-squashfs-sysupgrade.bin
via OpenWrt.
The integrated power monitoring and relay do not work in OpenWrt as the PL7223
chip source/documentation is unavailable.
Recovery
Mis-configuration can be dealt with using the RESET button to reset to factory,
worst case scenario will require some serious work and soldering, there's pads
on the PCB for both the UART and ETH0, and I soldered and tested that it does
work.
You will have to power the board using the header pins GND & 5V, see the 8-pin
header socket.
Rosen Penev [Mon, 25 Nov 2024 22:33:06 +0000 (14:33 -0800)]
ath79: pqi-air-pen: adjust mac addresses
The original ar71xx version of this device used 1002 as mac address for
both ethernet and wireless. The ath79 version inexplicably changes this
to 2, which seems to be done nowhere else in ath79, indicating it's
bogus.
Restore previous ar71xx assignment. 1002 is used as an ethernet
interface with some other devices as well.
Also remove the bogus caldata userspace extraction. The size is bogus
and it's already handled in dts.
The MAC addresses are derived from the `fac_mac` field in the `bdinfo` partition, formatted as `fac_mac = HWMAC`. The allocation is as follows:
| Vendor | OpenWrt Interface | Address | Notes |
|---------|-------------------|---------------|------------------------------------------------|
| LAN | br-lan | Label MAC | Default |
| WAN | lan4 | Label MAC+1 | Only when lan4 is switched to WAN |
| 2.4GHz | phy0-ap0 | Label MAC | |
| 5GHz | phy1-ap0 | Label MAC | (Local Admin bit set) |
| Modem | eth1 | Label MAC+2 | |
1. Log in to the router via `http://192.168.66.1`/.
2. Upgrade the official firmware to dual-system mode.
3. Select **Burn second system** and upload the `sysupgrade.bin` image.
- Download the image from the OpenWrt build system or build it yourself using the OpenWrt buildroot.
4. Wait for 30 seconds and click **Switch system**.
5. The device will reboot and switch to OpenWrt.
Set the U-Boot environment variable `boot_system=0` and reboot:
```bash
fw_setenv boot_system 0
```
Power off the router, hold the **WPS button**, and power it back on.
1. Rename the stock firmware file to **`recovery.bin`**.
2. Set your PC's Ethernet IP to **192.168.1.88** and connect it to the lan1 port on the router.
3. Run a TFTP server and place the `recovery.bin` file in its root directory.
4. Power off the router, press and hold the **Reset button**, and power it back on.
5. Release the Reset button when the TFTP server shows activity.
6. Wait for the router to flash the firmware and reboot automatically.
- By default, `lan4` is part of `br-lan` and uses the label MAC address.
- To query the RM520N-GL module, use the following command:
```bash
cat /dev/ttyUSB2 & printf 'ATI\r\n' > /dev/ttyUSB2
```
David Bauer [Sat, 7 Dec 2024 13:47:29 +0000 (14:47 +0100)]
wifi-scripts: don't fail on unset PSK
Don't fail wireless interface bringup on empty PSK set. This is a valid
configuration, resulting in a PSK network which can't be connected to.
It does not fail the bringup of the hostapd process.
Keep failing the interface setup in case a password with invalid length
is used.
This is also beneficial when intending to configure a PPSK network. It
allows to create a network where no PPSK is yet set.
Andreas Gnau [Tue, 28 Feb 2023 11:24:57 +0000 (16:54 +0530)]
dropbear: Name pid file by uci section name
Name the pidfile of each dropbear instance according to the
corresponding uci section name. This enables a 1:1 mapping between the
definition of the service instance and its process.
Sybil127 [Thu, 23 May 2024 16:49:54 +0000 (18:49 +0200)]
hostapd: add support for rxkh_file
Initial support for dynamic reload of RxKHs.
In order to check if RxKHs need reloading.
RxKHs defined in the rxkh_file first has to be parsed and formated,
the same way as hostapd will read from the file and also output,
with the command GET_RXKHS.
Then each list of RxKHs can be hashed and compared.
Ucode implementation of hostapds rkh_derive_key() function.
Hostapd converts hex keys with 128-bits or more when less than 256-bits
to 256-bits, and truncates those that are more than 256-bits.
See: https://w1.fi/cgit/hostap/commit/hostapd/config_file.c?id=245fc96e5f4b1c566b7eaa19180c774307ebed79
Signed-off-by: Sybil127 <sybil127@outlook.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sybil127 [Thu, 23 May 2024 15:43:07 +0000 (17:43 +0200)]
wifi-scripts: introduce rxkh_file uci option
With rxkh_file, hostapd will read a list of RxKHs from a text file.
This also makes it possible for hostapd to dynamically reload RxKHs.
RxKHs defined in rxkh_file should be formated as described in hostapd.conf,
with one entry per line.
R0KH/R1KH format:
r0kh=<MAC address> <NAS Identifier> <256-bit key as hex string>
r1kh=<MAC address> <R1KH-ID> <256-bit key as hex string>
Reworked behavior of the uci options r0kh and r1kh.
When rxkh_file is not configured:
Instead of appending the RxKHs to the hostapd bss configuration.
They will be added to a interface specific file with name
/var/run/hostapd-phyX-apX.rxkh.
This file will be used as the rxkh_file in the hostapd bss configuration.
When rxkh_file is configured:
The specified file will be used in the hostapd bss configuration,
and will be the only source for configured RxKHs.
All RxKHs defined with the uci options r0kh or r1kh will be ignored.
Signed-off-by: Sybil127 <sybil127@outlook.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
David Bauer [Thu, 12 Dec 2024 15:36:50 +0000 (16:36 +0100)]
wifi-scripts: fix failing mesh setup with missing wpa_supplicant
The initialization of mesh interfaces currently fail when wpa_supplicant
is not installed. This is due to the script calling the wpa_supplicant
feature indicator without verifying wpa_supplicant is installed at all.
To avoid failing, first check if wpa_supplicant is installed before
determining the available featureset.
Jonathan Brophy [Tue, 10 Sep 2024 09:43:23 +0000 (21:43 +1200)]
kernel: modules: add support for led-group-multicolor
This option enables support for monochrome LEDs that are grouped into multicolor
LEDs which is useful in the case where LEDs of different colors are physically
grouped in a single multi-color LED and driven by a controller that doesn't have
multi-color support.
We have seen hung devices and failures during SPI transactions on
Fritzbox devices with a gluon based freifunk network. We have narrowed
down that disabling DMA for spi fixes the problem, so disable dma for
the SPI controller on the Fritzbox 4040.
Mark Mentovai [Sat, 27 Jul 2024 03:28:36 +0000 (23:28 -0400)]
.gitattributes: ignore some whitespace "violations" in .patch files
git's default core.whitespace[1] setting doesn't agree with .patch
files. This causes whitespace warnings when running `git apply`,
(including via `git am`) and causes red highlighting when viewing diffs
to .patch files via `git diff` (including via `git show`) when
outputting to a terminal.
These types of whitespace “violations” will now be explicitly disabled
for .patch files in the repository-wide .gitattributes file to prevent
git from suggesting that there’s anything wrong with checked-in .patch
files.
A .patch file will naturally have `space-before-tab` if a context line
(not a +/- line) begins with a tab character (as is common in patches to
files that use the tab indent convention), and will also naturally have
`trailing-space` if a context line is blank (also common).
Neither `indent-with-non-tab` nor `tab-in-indent` are enabled in
core.whitespace by default, but could also occur naturally in .patch
files, and are also explicitly disabled here for completeness to cover
cases where they may be enabled in core.whitespace at the global or
system level.
These false violations may be flagged frequently in OpenWrt, because the
repository contains many .patch files. There are currently just over
5,000 .patch files, representing slightly more than half of all files.
Markus Gothe [Tue, 7 Feb 2023 21:00:33 +0000 (22:00 +0100)]
rules.mk: Update ccache's compiler check.
Update the compiler check for ccache so we don't
end up with the wrong binaries. Right now the
compiler check will not be able to correctly
distinguish the compiler used for build
ARMv8 binaries from the one used to build
ARMv7 binaries.
Chuck R [Sun, 8 Sep 2024 19:28:06 +0000 (14:28 -0500)]
dnsmasq: pass environment variables to hotplug
dnsmasq passes a limited amount of information via DHCP script arguments. Much
more information is available through environment variables starting with
DNSMASQ_, such as DNSMASQ_INTERFACE. However, when the dhcp-script builds its
JSON environment and passes it to hotplug, all of this information is discarded
since it is not copied to the JSON environment.
Personally, I have a custom-made set of DDNS scripts and rely on environment
variables such as DNSMASQ_INTERFACE in order to determine which DNS zones
to update. So, not being able to access these variables was detrimental to me.
I patched in a quick copy of all DNSMASQ_ variables to the JSON environment
so that they can be used in hotplug scripts. In order to do so I also copied
/usr/bin/env into dnsmasq's chroot jail.
Rany Hany [Mon, 2 Dec 2024 11:30:07 +0000 (11:30 +0000)]
hostapd: add SAE support for wifi-station and optimize PSK file creation
Regarding SAE support in wifi-station:
Important Note: Unlike PSK wifi-stations, both `mac` and `key` options are required
to make it work. With PSK, hostapd used to perform a brute-force match to find which
PSK entry to use, but with SAE this is infeasible due to SAE's design.
When `mac` is omitted, it will allow any MAC address to use the SAE password if it
didn't have a MAC address assigned to it, but this could only be done once.
The last wildcard entry would be used.
Also, unlike "hostapd: add support for SAE in PPSK option" (commit 913368a),
it is not required to set `sae_pwe` to `0`. This gives it a slight advantage
over using PPSK that goes beyond not needing RADIUS.
Example Configuration:
```
config wifi-vlan
option iface default_radio0
option name 999
option vid 999
option network management
config wifi-station
# Allow user with MAC address 00:11:22:33:44:55 and matching
# key "secretadminpass" to access the management network.
option iface default_radio0
option vid 999
option mac '00:11:22:33:44:55'
option key secretadminpass
config wifi-vlan
option iface default_radio0
option name 100
option vid 100
option network guest
config wifi-station
# With SAE, when 'mac' is omitted it will be the fallback in case no
# other MAC address matches. It won't be possible for a user that
# has a matching MAC to use this network (i.e., 00:11:22:33:44:55
# in this example).
option iface default_radio0
option vid 100
option key guestpass
```
Regarding PSK file creation optimization:
This patch now conditionally runs `hostapd_set_psk_file` depending on `auth_type`.
Previously, `hostapd_set_psk` would always execute `hostapd_set_psk_file`, which
would create a new file if `wifi-station` was in use even if PSK was not enabled.
This change checks the `auth_type` to ensure that it is appropriate to parse the
`wifi-station` entries and create those files.
Furthermore, we now only configure `wpa_psk_file` when it is a supported option
(i.e., psk or psk-sae is used). Previously, we used to configure it when it was
not necessary. While it didn't cause any issues, it would litter `/var/run` with
unnecessary files. This patch fixes that case by configuring it depending on the
`auth_type`.
The new SAE support is aligned with these PSK file changes.
John Crispin [Wed, 11 Dec 2024 14:41:21 +0000 (15:41 +0100)]
umdns: update to latest HEAD
93458ac dns: fix response to TYPE_PTR query 68af311 fix unicast response port and timeout a2b4979 service: announce all services in single dns answer 4537734 display announced services in ubus call umdns browse 0b50c29 display more srv attributes in output of ubus browse function
To take advantage of the bigger kernel partition,
the uboot environment has to be changed:
setenv nboot 'nand read 0x81000000 0x60000 0x500000; bootm 0x81000000'
setenv bootcmd 'run nboot'
saveenv
Of course you need a u-boot capable of handling this.
The u-boot discussed in this forum thread:
https://forum.openwrt.org/t/zyxel-p2812hnu-f1-u-boot/100281
should be able to handle kernels up to an uncompressed size of 16MiB.
Allows us to drop 2 upstreamed patches:
package/network/utils/iproute2/patches/010-bridge-mst-fix-a-musl-build-issue.patch
package/network/utils/iproute2/patches/011-bridge-mst-fix-a-further-musl-build-issue.patch
The device path to the devices changed. Migrate the wifi
configurations from the old path to the new one. This is needed to
migrate Wireless configurations from OpenWrt 23.05 to OpenWrt 24.10.
This script is based on these two files:
target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
Ondřej Niesner [Sat, 7 Dec 2024 16:55:29 +0000 (17:55 +0100)]
mediatek: filogic: prevent faulty mac address assignment
The vendor U-Boot on the Cudy WR3000 assign random mac addresses on boot
and set the 'local-mac-address' property which prevents Openwrt from
assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add
the property.
Related to: a55ab9e1343e ("mediatek: filogic: prevent faulty mac address assignment") Fixes: https://github.com/openwrt/openwrt/issues/15587 Signed-off-by: Ondřej Niesner <ondra.niesner@seznam.cz> Link: https://github.com/openwrt/openwrt/pull/17201 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Eric Long [Mon, 25 Nov 2024 13:26:47 +0000 (21:26 +0800)]
bpftool: turn off libbfd feature in host build
libbfd feature is not used when building eBPF program, and it makes bpftool fail to build in a clean environment, since binutils in toolchain have libbfd disabled.
Notes:
* The device supports dual boot mode
* Fn led reassigned to wlan 2.4
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3811-squashfs-factory.bin"
to "KN-3811_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Hannu Nyman [Thu, 5 Dec 2024 20:28:45 +0000 (22:28 +0200)]
busybox: Save shell history into /tmp
Enable the busybox feature to save shell command history.
(.apk size increase 0.5 kB)
To prevent flash wear,
* save history only at the exit from a shell session, and
* set /tmp as the default location for the history file. The history
is kept on ramdisk until a reboot, when the history is then lost.
If the user wants to save history onto flash, he can change the location
definition in /etc/profile.d/busybox-history-file.sh
Pavel Shirov [Sat, 7 Dec 2024 12:29:28 +0000 (15:29 +0300)]
kernel: packages: fix building package/devel/perf with -O3
Add patch to fix failure to build package/devel/perf when
CONFIG_TARGET_OPTIMIZATION has -O3 enabled with this error:
```
In function 'elf_close',
inlined from 'elf_close' at elf.c:41:6,
inlined from 'elf_find_func_offset_from_file' at elf.c:267:2:
elf.c:45:9: error: 'elf_fd.elf' may be used uninitialized [-Werror=maybe-uninitialized]
45 | elf_end(elf_fd->elf);
| ^~~~~~~~~~~~~~~~~~~~
elf.c: In function 'elf_find_func_offset_from_file':
elf.c:260:23: note: 'elf_fd.elf' was declared here
260 | struct elf_fd elf_fd;
| ^~~~~~
In function 'elf_close',
inlined from 'elf_close' at elf.c:41:6,
inlined from 'elf_find_func_offset_from_file' at elf.c:267:2:
elf.c:46:9: error: 'elf_fd.fd' may be used uninitialized [-Werror=maybe-uninitialized]
46 | close(elf_fd->fd);
| ^~~~~~~~~~~~~~~~~
elf.c: In function 'elf_find_func_offset_from_file':
elf.c:260:23: note: 'elf_fd.fd' was declared here
260 | struct elf_fd elf_fd;
| ^~~~~~
```
kernel: fallback-sprom: create separate header files
Create a separate header files fallback-sprom.h
for BCMA and SSB Fallback SPROM Driver
to add function prototypes to fallback-sprom.c as well.
This prevents missing function prototype errors.
Robert Marko [Sat, 7 Dec 2024 21:08:18 +0000 (22:08 +0100)]
qualcommax: ipq807x: add Netgear DEVICE_VARS
Add NETGEAR_BOARD_ID and NETGEAR_HW_ID to DEVICE_VARS as multiple devices
set them in their recipes, so without them being added to DEVICE_VARS then
simply the value from last recipe that gets evaluated is used and images
are generated with the wrong ID-s.
Linksys MR7350 is a 802.11ax Dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ6000 Quad core Cortex-A53(A73) 1.5GHz
* RAM: 512MB of DDR3
* Storage: 256Mb NAND
* Ethernet: 5x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5052 2x2@80MHz or 802.11a/b/g/n/ac/ax 1201 Mbps PHY rate
* LED-s:
* RGB system led
* USB blue led
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition:
fw_printenv -n boot_part
- Change the partition:
fw_setenv boot_part 1
or
fw_setenv boot_part 2
depending on the current partition
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin kernel
Co-Authored-by: Chukun Pan <amadeus@jmu.edu.cn> Co-Authored-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Vladyslav Andreichykov <vladdrako007@gmail.com> Link: https://github.com/openwrt/openwrt/pull/14807 Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Fri, 6 Dec 2024 17:21:20 +0000 (18:21 +0100)]
ucode: update to Git HEAD (2024-12-06)
47b54cf5a4b6 types: introduce `ucv_array_sort_r()` and `ucv_object_sort_r()` efeb57806552 types, vm: refactor usage of global variables f9d2faf67de6 vm: reset signals when freeing VM 4e86847d802d lib: utilize `ucv_array_sort_r()` and `ucv_object_sort_r()` c71444ea301f types: ucv_resource_create(): rename `typename` parameter to `type` 373df7299c79 nl80211: properly support split_wiphy_dump for single phys 9bcd25f54708 lexer: Preserve keyword, regexp flags until processing non-comment tokens 0a7ff4715cb8 main: pretty-print `-p` output by default 4c3d5b469156 struct: Add new buffer API for incremental packing/unpacking efc4122124cb struct: do not use global variables for caching types
Fixes: https://github.com/jow-/ucode/issues/248 Fixes: https://github.com/jow-/ucode/issues/250 Fixes: https://github.com/efahl/owut/issues/25 Link: https://github.com/openwrt/openwrt/pull/17191 Signed-off-by: Robert Marko <robimarko@gmail.com>
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.itb
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Notes:
- The device supports dual boot mode
- The firmware partitions were concatenated into one
- The status button has been reassigned as the WPS button.
Flash instruction:
This device doesn't support sysupgrade, so the only way to flash OpenWrt image
is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-keenetic_kn-3211-squashfs-factory.bin"
to "KN-3211_recovery.bin" and place it in tftp server directory.
3. Connect PC with the ethernet port, press the reset button, power up
the router and keep button pressed until power led starts blinking.
4. Router will download file from server, write it to flash and reboot.
Eric Fahlgren [Thu, 5 Dec 2024 15:06:46 +0000 (07:06 -0800)]
apk: add dependency on wget provider
The apk-* packages contain no declared dependencies on a wget provider,
which is required for proper operation. Let's add it.
Fixes: https://github.com/openwrt/openwrt/issues/17173 Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com> Link: https://github.com/openwrt/openwrt/pull/17176 Signed-off-by: Robert Marko <robimarko@gmail.com>
Rui Salvaterra [Thu, 28 Nov 2024 18:41:37 +0000 (20:41 +0200)]
busybox: update to 1.37.0
Add a patch to fix non-x86 builds, refresh patches and update/fix the
configuration as described in 98b09ba250 (cited here for future reference).
Config refresh:
Refresh commands, run after busybox is first built once:
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.37.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.37.0/.config > Config-defaults.in
Manual edits needed after config refresh:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* Config-defaults.in: correct the default ports that get reset
BUSYBOX_DEFAULT_FEATURE_HTTPD_PORT_DEFAULT 80
BUSYBOX_DEFAULT_FEATURE_TELNETD_PORT_DEFAULT 23
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in: change at "Options common to all shells" the conditional symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit a few Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014fcca)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[rebased with the change download line commit]
[corrected version in the refresh example in commit message] Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> Link: https://github.com/openwrt/openwrt/pull/17107 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Golle [Thu, 5 Dec 2024 01:32:00 +0000 (01:32 +0000)]
feeds.conf.default: enable video feed by default
As discussed in the previous OpenWrt meeting the easiest way to have
regular builds of packages on the video feed without adding additional
complexity is by enabling the video feed by default.
If that slows down the buildbots beyond being useful we can always
disable it again and find another way to only sporadically build
packages of the video feed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Robert Marko [Wed, 4 Dec 2024 14:09:23 +0000 (15:09 +0100)]
hostapd: enable EAP-pwd support only for the SSL variants
The internal hostapd version cannot be built with EAP-pwd support, so
enable it only for the SSL variants.
Fixes: #17163 Fixes: 6365316fab87 ("hostapd: add ubus support for wired driver") Link: https://github.com/openwrt/openwrt/pull/17164 Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Wed, 4 Dec 2024 12:31:24 +0000 (13:31 +0100)]
build: add locking around dtc call after running mkits.sh
mkits.sh creates a root.*.pagesync file with padding, which is global, and
the generated .its files reference it. Since dtc reads this file, it must
not run at the same time as mkits.sh
Fixes generating itb images with broken rootfs.
Robert Marko [Mon, 2 Dec 2024 18:54:36 +0000 (19:54 +0100)]
apk: update to Git HEAD (2024-11-30)
3da6c104f0f5 database: use APK_DB_LAYER_ROOT in more places 5437e3abada1 audit: add usr/lib/apk to the list of protected paths under --full de9baf912245 change default db location to /usr, but detect and use /lib if exists 218fdaa1a1a2 context: close root_fd on free d33294236cb4 database: add support for only-when-modified trigger paths 36935db0ef3b package: fix memfd_create warnings on Linux kernels < 6.7 1c3fc36051a3 blob: add and use apk_blob_trim_{start,end} af5f9e3f93b0 pkg: fix v3 package size setting to installeddb 9428e34694c8 version: allow --check and --test to work without database 4b4add5326a8 test: fix unit test registration function to be unique eac18cb200d4 test: add testlib.sh for user tests 20dae205b006 mkpkg: fix creation of package with hardlinks 7bdecdca6a95 pkg: only allow tags in world and some commands 76de228bcc0b commit: show tags of world constrains 9a1b1cf68420 test: use testlib for solver.sh 99fc2a2a5efc test: remove dependency on GNU tar 6927746b9a10 Revert usrmerge/LFS related changes to apk used paths 5d287a9b06e9 apk-tools-3.0.0_pre5 8d93a79fb895 mkpkg: fix hardlink on big-endian system
build: Unconditionally append kmod feed for BuildBot
Recent changes to BuildBot config moved the kmods to a dedicated
directory and dropped them from the packages dir. This was needed as
both OPKG and APK gets confused if both entry are present.
To fix this, unconditionally append the kmod feed line if
CONFIG_BUILDBOT is enabled.
Daniel Golle [Mon, 2 Dec 2024 01:05:01 +0000 (01:05 +0000)]
meson: allow using staging python
Introduce package flag MESON_USE_STAGING_PYTHON which allows packages
to be built with the OpenWrt-built python3/host instead of relying on the
buildhost's Python distribution.
This is useful for packages using Meson which require additional Python
modules during build.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
John Crispin [Tue, 22 Oct 2024 07:58:48 +0000 (09:58 +0200)]
wifi-scripts: add ucode based iwinfo
Add an ucode based re-implementation of iwinfo. The tool behaves like the old
one with a few minor output differences. It is now possible to add -j to any
command resulting in JSON output.
The new code is currently opt-in via WIFI_SCRIPTS_UCODE and defaults to
EXPERIMENTAL.
John Crispin [Fri, 1 Nov 2024 08:26:15 +0000 (09:26 +0100)]
ucode: update to latest HEAD
b0b5d93 Merge pull request #234 from IdWV/fs 60e7a88 Merge pull request #232 from sebastianertz/lib-digest 1752779 digest: implement compile time option to exclude less common algorithms c7268a1 ci: include libmd in MacOS CI builds fcb6f70 lib: introduce digest library 1323a27 Merge pull request #246 from jow-/fix-upvalue-resolve ed5ce8f types: resolve upvalue values in arrays and objects a6e0641 vm: resolve upvalues before pushing them onto the stack ef1baab ci: drop OpenWrt tests for now 63e18ea fs: eliminate the usage of global variables b1bd7b5 types: add ucv_resource_create() helper 3408edf Merge pull request #244 from nbd168/nl80211 8af77e7 nl80211: add new attributes for multi-radio support 1423ad7 nl80211: cover extended feature and EHT rate info attributes ee1d6d8 Merge pull request #237 from sebastianertz/math 4b18a9b Merge pull request #213 from jow-/improve-vector-macros 1f022c0 math: removed global variable for thread safety e5fe6b1 treewide: refactor vector usage code 20307ee utils: improve vector utilities aa18952 Merge pull request #241 from jow-/socket-local-fanout-decl 79ccd9c socket: provide local definition of `struct fanout_args` 402280d Merge pull request #239 from jow-/safe-insert-during-obj-iteration 07afe96 Merge pull request #240 from jow-/stricter-number-conversion 736d450 types: fix potential use after free on adding keys during iteration 4134e71 vallist: more thoroughly check for trailing garbage after numeric string 9cf53dd Merge pull request #226 from jow-/lexer-improvements 2b2e732 lexer: make api functions public 855854f lexer: emit comment and template statement block tokens 328a50f lexer: improve token position reporting fa22732 Merge pull request #225 from jow-/compiler-fix-keyword-property-labels-after-spread 6e88c62 Merge pull request #224 from jow-/lib-fs-readline-leak 94d1211 compiler: properly treat property names after spread expressions 67cd123 fs: fix potential memory leak on i/o errors in .read()
John Crispin [Fri, 29 Nov 2024 07:40:08 +0000 (08:40 +0100)]
hostapd: add radius WISPr rate control AVPs
This allows a radius server to send AVPs for client rate control inside the
accept message. Further add the ratelimits to the sta-authorized ubus
notification.
projects / thirdparty / openwrt.git / log
