The OEM firmware has telnet enabled by default. If not, it can be enabled
from the firmware web interface. You need a TFTP server on your computer
and the OpenWrt factory image should be available as "n650factory.bin".
It is assumed that your computer has the IP 192.168.1.1 and the N650
192.168.1.20 (default IP address).
1. Connect via Telnet to the device and log in with the default credentials
"admin:admin"
2. Exploit the limited interface by typing "ps & /bin/sh"
3. Press <ENTER> to start the shell
4. Enter the following commands:
UART installation is possible since the serial header is already soldered
on. The pinout is GND - Tx - Rx - VCC from top to bottom (RJ45 ports are
at the bottom). Connect with 115200 8N1.
First, boot OpenWrt from TFTP. Enter the following commands in the U-Boot
shell, assuming your computer has the IP address 192.168.1.1 and a TFTP
server running where the initramfs image is provided as n650.bin:
Back to stock is only possible if you saved a partition backup before
installing OpenWrt. Assuming you have fullbackup.bin covering the whole
flash, you need to prepare the image as follows:
Update to checksum only/no patches required a rebase.
Per the changelog, this is a trivial upstream bump with only 4
commits, 2 of which being reverts.
David Bauer [Thu, 12 Dec 2024 15:36:50 +0000 (16:36 +0100)]
wifi-scripts: fix failing mesh setup with missing wpa_supplicant
The initialization of mesh interfaces currently fail when wpa_supplicant
is not installed. This is due to the script calling the wpa_supplicant
feature indicator without verifying wpa_supplicant is installed at all.
To avoid failing, first check if wpa_supplicant is installed before
determining the available featureset.
86da5cbcdb9d system-linux: do not pull ifindex/flags from netlink messages on rtnl events cd96f61ba63e proto-shell: fix spurious interface teardowns with host deps a39fe3a8b150 wireless: add support for adding a list of devices for a wifi-iface d29cf707478c iprule: add ipproto property 768027c5a764 system-linux: restore reading flags from netlink messages
This commit adds OpenWrt U-Boot (UBI) layout support for MERCUSYS MR90X
v1.
Stock U-Boot UBI size: 50 MiB
OpenWrt U-boot UBI size: 126 MiB
Install
-------
1. Perform steps 1-14 of the OpenWrt installation guide (use OpenWrt
initramfs-recovery.itb instead of initramfs-kernel.bin at the step 10,
12 and 14). Link: https://openwrt.org/toh/mercusys/mr90x_v1#installation
2. Make backups:
```
cat /dev/mtd0 > /tmp/boot.bin
cat /dev/mtd5 > /tmp/tp_data.bin
```
Copy /tp_data dir content, /tmp/boot.bin and /tmp/tp_data.bin and to
your PC using scp. You can also backup the remaining partititons. Copy
backups to a safe place, they are required for the next steps and stock
firmware recovery.
3. Reboot to OpenWrt initramfs:
```
reboot
```
4. Copy OpenWrt ubi-bl31-uboot.fip, ubi-preloader.bin,
ubi-squashfs-sysupgrade.itb and MT7986_EEPROM.bin, default-mac (from
/tp_data backup) to the /tmp folder of the router using scp.
Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
button.
3. Use OpenWrt initramfs system for recovery.
4. Erase UBI and reboot:
```
mtd erase ubi
reboot
```
5. Open U-Boot web recovery, upload stock firmware image and start
upgrade. Link: http://192.168.1.1
6. Complete steps 1-9 of the OpenWrt installation guide to get root
rights. Link: https://openwrt.org/toh/mercusys/mr90x_v1#installation
7. Upload "tp_data" partition backup (tp_data.bin) to the /tmp folder of
the router using scp.
The device path to the devices changed. Migrate the wifi
configurations from the old path to the new one. This is needed to
migrate Wireless configurations from OpenWrt 23.05 to OpenWrt 24.10.
This script is based on these two files:
target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
Ondřej Niesner [Sat, 7 Dec 2024 16:55:29 +0000 (17:55 +0100)]
mediatek: filogic: prevent faulty mac address assignment
The vendor U-Boot on the Cudy WR3000 assign random mac addresses on boot
and set the 'local-mac-address' property which prevents Openwrt from
assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add
the property.
Eric Long [Mon, 25 Nov 2024 13:26:47 +0000 (21:26 +0800)]
bpftool: turn off libbfd feature in host build
libbfd feature is not used when building eBPF program, and it makes bpftool fail to build in a clean environment, since binutils in toolchain have libbfd disabled.
Marty Jones [Mon, 25 Nov 2024 17:58:57 +0000 (12:58 -0500)]
mac80211: realtek: backport support for RTL8812AU/RTL8821AU
Backport support for RTL8812AU/RTL8821AU USB adapters
Manually backported patch:
045-v6.13-wifi-rtw88-Enable-the-new-RTL8821AU-RTL8812AU-driver
Patches from 046 to 051 are pending.
Robert Marko [Sat, 7 Dec 2024 21:08:18 +0000 (22:08 +0100)]
qualcommax: ipq807x: add Netgear DEVICE_VARS
Add NETGEAR_BOARD_ID and NETGEAR_HW_ID to DEVICE_VARS as multiple devices
set them in their recipes, so without them being added to DEVICE_VARS then
simply the value from last recipe that gets evaluated is used and images
are generated with the wrong ID-s.
build: Unconditionally append kmod feed for BuildBot
Recent changes to BuildBot config moved the kmods to a dedicated
directory and dropped them from the packages dir. This was needed as
both OPKG and APK gets confused if both entry are present.
To fix this, unconditionally append the kmod feed line if
CONFIG_BUILDBOT is enabled.
"ethaddr" is stored into the "u-boot-env" (stock: "Config") partition
and it's quoted with double-quotations, but that format is not supported
by the current NVMEM u-boot-env driver (and mac_pton() function) and the
MAC address won't be parsed to byte array.
This causes random MAC addresses on the adapters, so revert the above
commit.
Petr Štetiar [Wed, 27 Nov 2024 08:32:01 +0000 (08:32 +0000)]
apk: mark package as broken to hide it by default
During the last OpenWrt developer meeting 2024-11-26 it was decided,
that 24.10 will be the last release using opkg package manager and thus
apk won't be supported, so make it explicit and mark apk package manager
as broken.
Hannu Nyman [Sun, 10 Nov 2024 15:16:51 +0000 (17:16 +0200)]
gdb: Fix description for apk, remove backtick
Remove backtick from gdb description text, as that seems to
be recognized as a shell action by compilation with apk,
causing error.
Example from test buildbot:
rstrip.sh: /builder/shared-workdir/build/sdk/build_dir/target-aarch64_generic_musl/gdb-15.2/ipkg-aarch64_generic/gdb/usr/bin/gdb: executable
bash: -c: line 1: unexpected EOF while looking for matching ``'
bash: -c: line 2: syntax error: unexpected end of file
make[3]: *** [Makefile:123: /builder/shared-workdir/build/sdk/bin/packages/aarch64_generic/base/gdb-15.2-r1.apk] Error 2
Local compilation:
rstrip.sh: /OpenWrt/aarch64/build_dir/target-aarch64_cortex-a53_musl/gdb-15.2/ipkg-aarch64_cortex-a53/gdb/usr/bin/gdb: executable
bash: -c: line 1: unexpected EOF while looking for matching ``'
make[2]: *** [Makefile:123: /OpenWrt/aarch64/bin/packages/aarch64_cortex-a53/base/gdb-15.2-r1.apk] Error 2
John Audia [Sun, 29 Oct 2023 08:32:21 +0000 (04:32 -0400)]
kernel: enable pressure interface
PSI provides a canonical way to see resource pressure increases as
they develop, with pressure metrics for three major resources:
memory, CPU, and IO. PSI stats are like barometers that provide
fair warning of impending resource shortages, enabling users to
take more proactive, granular, and nuanced steps when resources
start becoming scarce.
This commit adds OpenWrt U-Boot layout support for Routerich AX3000. The
aims:
1. Get open-source U-Boot;
2. Get maximum available free space in OpenWrt.
Install
-------
1. Copy OpenWrt ubootmod-bl31-uboot.fip, ubootmod-preloader.bin, to the
/tmp folder of the router using scp.
2. Make mtd partitions backups:
http://192.168.1.1/cgi-bin/luci/admin/system/flash -> Save mtdblock
contents
5. Copy OpenWrt ubootmod-initramfs-recovery.itb to the tftp server root
with IP 192.168.1.254.
6. Reboot router:
```
reboot
```
U-Boot will automatically download from the tftp server and boot OpenWrt
initramfs system.
7. Copy OpenWrt ubootmod-squashfs-sysupgrade.itb to the /tmp dir of the
router using scp.
8. Run sysupgrade:
```
sysupgrade -n /tmp/squashfs-sysupgrade.itb
```
Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
button.
3. Use OpenWrt initramfs system for recovery.
BL2 and FIP recovery
--------------------
Use mtk_uartboot and UART connection if BL2 or FIP in UBI is destroyed: Link: https://github.com/981213/mtk_uartboot
Return to stock:
----------------
1. Copy partition backups (BL2.bin and FIP.bin) to the /tmp dir of the
router using scp.
The mt76x8 series SoCs use the MIPS generic systick timer. Sync the
upstream Ralink systick driver changes and disable it for mt76x8
target to reduce the kernel size.
Hauke Mehrtens [Sun, 24 Nov 2024 13:39:57 +0000 (14:39 +0100)]
x86: Deactivate kernel options with extra overhead
Deactivate CONFIG_CONTEXT_TRACKING_USER_FORCE: Force user context
tracking: This is a testing feature which should not be activate in
production environments according to the Kconfig help. It adds an extra
overhead.
Deactivate CONFIG_RCU_NOCB_CPU_DEFAULT_ALL: Offload RCU callback
processing from all CPUs by default: This option should only be used in
aggressive HPC or real-time workloads which we do not have in OpenWrt.
For normal workloads it increases the number of context switches.
In the default Arch Linux kernel both options are not activated.
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000s.bin"
George Oldfort [Mon, 11 Nov 2024 10:18:19 +0000 (11:18 +0100)]
mediatek: add support for Acer Predator W6d and Acer Vero W6m
This commit adds support for two variants of the already supported router
Acer Predator Connect W6: The Acer Predator Connect W6d (W6 without 6 GHz
wifi) and the Acer Connect Vero W6m (W6 without 2.5G eth1 port, usb3 port,
and the 6 on-board gpio RGB LEDs, and with a KTD2026 RGB LED controller
instead of the KTD2061 LED controller of the W6/W6d).
The device tree for the W6m refers to the KTD202x driver suggested in
PR #16860.
Patching target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
removes the code repetition in (old) lines 121 to 124 on the occasion.
This is the last of four commits into which the original commit was split
to make reviews easier and more targeted.
George Oldfort [Mon, 11 Nov 2024 09:40:45 +0000 (10:40 +0100)]
mediatek: improve device tree for Acer Predator Connect W6
In order to prepare for OpenWrt support other Acer W6 devices and to get
a step further to full hardware support for Acer Predator Connect W6, this
commit
- adjusts the product name ("Acer Predator Connect W6")
- updates gpio LED labels to function/color scheme
- show router status by using first rgb led instead of it's red color only
(blue: booting/failsafe mode; red: sysupgrade; green: running – was: red)
- changes switch/eth1 led configuration to reflect RX/TX activity and speed
(green: full 1Gbps/2.5Gbps speed; amber: lower speed; blink: RX/TX)
- shortens dummy dm-mod.create string in bootargs
- enables W6's i2c interface
This is the third of four commits into which the original commit was split
to make reviews easier and more targeted.
George Oldfort [Mon, 11 Nov 2024 09:14:55 +0000 (10:14 +0100)]
mediatek: make use of Acer Predator Connect W6's u-boot environment
In order to prepare OpenWrt support for other Acer W6 devices and to adapt
the procedure to read and set mac addresses which other devices of the same
target are using (instead of needing an additional script and creating an
additional structure in the file system), this commit
- reads device mac addresses from u-boot environment
- avoids the detour via the file system to set the mac addresses
- drops redundant file /lib/preinit/05_extract_factory_data.sh
The idea and the implementation were thankfully taken from PR #16410.
This is the second of four commits into which the original commit was split
to make reviews easier and more targeted.
George Oldfort [Mon, 11 Nov 2024 08:25:56 +0000 (09:25 +0100)]
mediatek: split Acer/W6 dts into W6 common dtsi and device specific dts
In order to prepare OpenWrt support for other Acer W6 devices, this commit
moves all device tree components that are used by all Acer W6/W6e/W6d/W6m
routers from mt7986a-acer-predator-w6.dts to mt7986a-acer-w6-common.dtsi
(new file) and includes this dtsi file in mt7986a-acer-predator-w6.dts.
Minor changes had to be made to the device tree in order to improve clarity
and – notably – to reduce the number of dtc warnings:
- replace (obviously wrong) led@<N> gpio led entities by led-<N>
- remove unnecessary (default-state = "off") gpio led statements
- rename entity “memory” to “memory@0”
- add missing #address-cells and #address-size in /soc/mmc@11230000
- add missing #address-cells and #address-size in /soc/pcie@11280000
- introduce symbols “nvmem” and “swport0” in dtsi (referenced in dts)
The changes were checked with `diff -BEZbdtwy --suppress-common-lines ...`
(comparing two dts files created using old and new fdt-1 blobs again), see
https://github.com/openwrt/openwrt/pull/16861/#issuecomment-2455680020 .
This is the first of four commits into which the original commit was split
to make reviews easier and more targeted.
Tim Noack [Mon, 21 Oct 2024 12:21:59 +0000 (12:21 +0000)]
ath79: add support for TP-Link CPE710-v2
TP-Link CPE710-v2 is an outdoor wireless CPE for 5 GHz with one Ethernet
port based on the AP152 reference board. Compared to the CPE710-v1, the
only change observed in hardware is that the mdio address of the ethernet
physical changed from 0x4 to 0x0.
Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
data rate), based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO parabolic antenna
- Power, LAN, WLAN5G Blue LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for around
30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.
Installation:
- Using the bootloader web server. Hold the reset button while turning
the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.
LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
(GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.
Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.
MAC addresses as verified by OEM firmware:
use address source
2g *:b0 factory 0x4 (label)
5g *:b1 factory 0x8004
LAN *:b2 factory 0x28
WAN *:b3 factory 0x2e
Antonio Pastor [Sat, 16 Nov 2024 20:09:49 +0000 (15:09 -0500)]
kernel: modules: appletalk: add for Netatalk v4
Netatalk v4 reintroduces AppleTalk and this module is required for
layer 3 protocol support.
Module was removed in kernel 4.14 for OpenWrt 18.06 (commmit 14a0131, 22/02/2018). At the time nothing used it as Netatalk v3
did not support AppleTalk.
Not building ipddp feature/module like it was in the past, as
recommended by upstream Netatalk maintainers.
Thomas Richard [Thu, 26 Sep 2024 14:55:22 +0000 (16:55 +0200)]
stm32: add new stm32 target
New stm32 target introduces support for stm32mp1 based devices.
For now it includes an initial support of the STM32MP135F-DK device.
The specifications bellow only list supported features.
Romanov Danila [Mon, 21 Oct 2024 18:34:34 +0000 (21:34 +0300)]
mediatek: change Routerich AX3000 ubi size
All new routers are shipped with ubi size 112MB since early September.
Bootloader update required (ask vendor , see wiki)
These partitions weren't used:
firmware_backup
zrsave
config2
Til Kaiser [Fri, 15 Nov 2024 15:49:14 +0000 (16:49 +0100)]
x86: add all ports to the Gowin 1U default network config
Commit e52c57bb1b30375e0bcc5523db76a672a4a8b4a4 renamed all
network ports to match the faceplate of the Gowin 1U Rack
Mount Server and added the br-lan bridge for the eth* ports.
This commit adds the PoE port to the br-lan bridge and a
br-wan bridge for the two SFP ports so that all ports are
part of the default network configuration.
pwm1 value fan rotation speed cpu temperature notes
-----------------------------------------------------------------
0 maximal 31.5 Celsius too noisy
40 optimal 35.2 Celsius no noise hearable
95 minimal
above 95 does not rotate 55.5 Celsius
-----------------------------------------------------------------
At the moment we have following cooling levels:
cooling-levels = <255 96 0>;
for cpu-active-high, cpu-active-medium and cpu-active-low modes correspondingly.
Thus only cpu-active-high and cpu-active-low are usable. I think this is wrong.
This patch fixes cpu-active-medium settings for bpi-r3 board.
PS: I know, the patch is not ideal as it can break pwm fan for some users.
There are some peoples that use handmade cooling solutions, but:
* discussed cooler is the only 'official' pwm cooler for bpi-r3
available on the market.
* most peoples will use passive cooling available on the market or
the discussed cooler.
* the pwm-fan dts section was added before the official cooler
appears on the market.
Thus it should not be a lot of harm from this fix.
Robert Marko [Mon, 18 Nov 2024 16:15:54 +0000 (17:15 +0100)]
omnia-eeprom: depend only on subtarget
Now that omnia-eeprom is marked nonshared building the cortex-a9 mvebu
subtarget will fail with:
ERROR: unable to select packages:
omnia-eeprom (no such package):
required by: world[omnia-eeprom]
This is because omnia-eeprom depends on TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia
which will not be satisfied in buildbots since CONFIG_TARGET_ALL_PROFILES
and CONFIG_TARGET_PER_DEVICE_ROOTFS are set in which case
CONFIG_TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia is not set.
So, lets simply depend on the mvebu/cortex-a9 subtarget.
Sergey Ponomarev [Mon, 27 May 2024 23:50:09 +0000 (02:50 +0300)]
dropbear: use config_get_bool enable
The config_get_bool also works with on/off, yes/no, true/false.
Add 'main' section name. This will make it easier to change settings from uci.
Add a link to documentation.
Hauke Mehrtens [Sat, 16 Nov 2024 17:38:42 +0000 (18:38 +0100)]
omnia-eeprom: Mark it nonshared
This tool was build in the phase 2 build, there the
TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia dependecy was probably
not meat. Mark it as non shared to build it together with the target
where this option is set.
Rodrigo Balerdi [Fri, 8 Nov 2024 20:40:03 +0000 (17:40 -0300)]
ipq807x: prpl haze & qnap 301w: use the standard eMMC sysupgrade code
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Also note that the qnap 301w has a 'rootfs_data' partition in the eMMC
that is being ignored by fstools during boot, presumably due to a bug.
This is why the partition is also ignored in the sysupgrade code and
there is no definition of CI_DATAPART="rootfs_data".
Since the start of the Realtek target OpenWrt works with RTL83XX as the
target architecture. Upstream is using MACH_REALTEK_RTL instead. To
simplify further development align that.
But there is no `libreadline.so` or `libhistory.so` available.
So this happens:
```
root@OpenWRT:~# cat a.c
int main() {
}
root@OpenWRT:~# gcc a.c -lreadline
/usr/bin/ld: cannot find -lreadline: No such file or directory
collect2: error: ld returned 1 exit status
```
Unless, of course, one uses `-l:libreadline.so.8`... But that
doesn't help with binaries that try to dynamically open
`libreadline.so`. I have one of those here (the STklos Scheme
compiler -- I didn't make a PR for it because it's far from
being ready, but one issue is that it does use dlopen to use
readline...)
Another example: when trying to package rlwrap, the build failed
complaining it could not find readline (using `-lreadline`).
It would then be necessary to change rlwrap's `configure.ac`
(and also in all packages that use readline), but it seems
simpler to add the symlinks...
This PR changes the Makefile so it will include the links.
John Audia [Mon, 2 Sep 2024 23:53:47 +0000 (19:53 -0400)]
x86: switch config to a tickless kernel
This commit fixes and closes #16313.
Switch the x86 kernel's timer to tickless operation which is
more power efficient since it is not woken up by periodic timer
interrupts when idle. Also add several other options for CPU
idle governors particularly the upstream default for tickless
kernels, CONFIG_CPU_IDLE_GOV_MENU. Without this commit, my AMD
Ryzen 7 5800U can only achieve a minimum core frequency of 1,384
MHz which is over 3x higher than the processor's minimum
frequency of 400 MHz which is accessible with this modification.
In addition to the lower clock rate, I have seen a concomitant
reduction in both idle temps and at-the-wall power consumption.
Summary:
* Idle CPU freqs dropped from 1,384 MHz to 400 Mhz.
* Idle power consumption dropped from 7 W avg to 5 W.
* Idle temps have dropped from 50C on avg to 43C.
There are other well known reasons to switch to a tickless
timer including: reduced interrupt overhead, better use of CPU
resources, and reduced latency to name a few.
Shiji Yang [Sun, 13 Oct 2024 13:15:59 +0000 (21:15 +0800)]
ppp: remove more unnecessary kernel checks
The ppp package can support all features since Linux 4.7.0 kernel.
Therefore, most kernel version checks can pass unconditionally on
OpenWrt v18.06 and later version. This patch can reduce the size
of ppp package by approximately 2.5 KB.
projects / thirdparty / openwrt.git / log
