MAC:
LAN MAC: label mac (eeprom@4)
WAN MAC: label mac (eeprom@4)
2.4G MAC: label mac (eeprom@4)
5G MAC: label mac + 1 (eeprom@8004)
Installation:
The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image
with the 'Keep settings' option turned off.
Robert Marko [Sat, 18 Jan 2025 11:25:01 +0000 (12:25 +0100)]
qualcommax: dl-wrx36: fix 2.5G port LED-s
Currently, 2.5G port LED-s on Dynalink are incorrectly configured and thus
they will light up all of the time.
So, lets fix this by:
1. Current green LED is actually yellow, change the color
2. Fix its polarity as its actually active-low
3. The yellow LED that was registered as being connected to LED_1 pin on
the PHY is not actually connected at all, so remove it.
4. The actual green LED is connected to LED_2 on the PHY so add it.
generic: r8169: remove reverted temperature sensor patch
The patch adding temperature sensor support for r8169 has been removed upstream
and the functionality will be added to Realtek PHY instead:
https://github.com/torvalds/linux/commit/1f691a1fc4bef1c5cf5f503e14e1a22fc37c97e3
Felix Fietkau [Thu, 16 Jan 2025 11:35:47 +0000 (12:35 +0100)]
netifd: improve packet steering on ipq40xx (and possibly others)
Some platforms a single ethernet device for all ports with multiple rx rings
and NAPI threading enabled. In this case, the steering script was limiting
performance by keeping all NAPI threads assigned to the same CPU.
Fix this by assigning each rx queue and the corresponding NAPI task separately.
Additionally, if the number of rx queues is at least as big as the number of
CPUs, skip weight based assignment and distribute the load across all CPUs
directly.
Fixes: https://github.com/openwrt/openwrt/issues/17611 Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit acce25b789d40f2d88a2326a7d9921bd1743fe54)
The package coreutils-stty is not part of the OpenWrt main packages. A
board can not depend on it. Remove the dependency to fix a build problem
seen in the build bots.
Use USB2.0 FAT32 pendrive with openwrt-mvebu-cortexa9-wd_cloud-mirror-gen2-initramfs-kernel.bin
1. stop boot by pressing 1
2. usb start
3. fatload usb 0:1 0x02000000 openwrt-mvebu-cortexa9-wd_cloud-mirror-gen2-initramfs-kernel.bin;bootm 0x02000000 -
4. do backup mtd1 mtd3
5. use sysupgrade
Or tftp
1. stop boot by pressing 1
2. setenv ethact egiga2;setenv serverip 192.168.11.114;setenv ipaddr 192.168.11.113
3. tftpboot 0x02000000 openwrt-mvebu-cortexa9-wd_cloud-mirror-gen2-initramfs-kernel.bin; bootm 0x02000000 -
4. do backup mtd1 mtd3
5. use sysupgrade
or Evgeny Kolesnikov <evgenyz@gmail.com> method from his failed PR 2040
- Using original firmware's network settings obtain SSH access to the device.
- Put *-image-cfs-factory.bin and *-uImage-factory.bin images into device's /tmp directory.
- Write kernel (uImage) image 'flash_eraseall /dev/mtd1 && nandwrite --markbad -p /dev/mtd1 /tmp/*-uImage-factory.bin'.
- Write rootfs (image-cfs) image 'ubiformat /dev/mtd3 -f /tmp/*-image.cfs-factory.bin -y'.
- Reboot the device.
Installation (upgrade):
Use *-sysupgrade.bin in a usual way.
Weltrend MCU control is done via uart1 19200
stty -F /dev/ttyS1 raw speed 19200
stty -F /dev/ttyS1 raw speed 19200
Power LED Control
Blue
echo -n -e '\xfa\x26\x00\x11\x00\x01\xfb' > /dev/ttyS1
Red
echo -n -e '\xfa\x26\x00\x14\x00\x01\xfb' > /dev/ttyS1
Orange
echo -n -e '\xfa\x26\x00\x12\x00\x01\xfb' > /dev/ttyS1
more here: https://github.com/c-MM/mcm-daemon/blob/master/mcm.h
Bringing up a mesh interface using wpa_supplicant already supports a
per-VIF basic rate selection. Add the same ability when creating a mesh
VIF without wpa_supplicant.
Sander Vanheule [Wed, 1 Jan 2025 19:05:20 +0000 (20:05 +0100)]
realtek: debounce reset key for Zyxel GS1900
When the reset button is next to the SFP cages, I2C operations on the
modules might cause interference on the button's GPIO line. Add a
debounce-interval of 5 times the poll-interval to ensure the line is
actually stable for some time and not just glitching.
This squashes commit 4357f32d41eb ("realtek: debounce reset key for
Zyxel GS1900") and commit 777c6106ed4e ("realtek: move debounce-interval
to correct node").
Lech Perczak [Mon, 6 Jan 2025 16:31:44 +0000 (17:31 +0100)]
ath79: teltonika-rut230: fix failsafe boot without SIM tray
Due to "SIM present" input defaulting to "button" type, it is
interpreted as such when booting, and causes the system to enter
failsafe, if the tray is missing. Similarly to rfkill switch on
TP-Link WDR4300 and Archer C7, make it EV_SW instead, to stop it from
interfering with the boot process.
OpenWRT on the WNDAP6x0 refuses to sysupgrade to itself
due to a compat_version imbalance. The Image is generated
with version 2.0, but the uci-defaults says that it needs
to be at 3.0 for the device.
Fix this by downgrading WNDAP6x0 05_fix-compat-version's
values back to 2.0 so it matches what we use.
Fixes: 5815884c3a2a ("apm821xx: migrate to DSA") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit e9415be4ad3cacbbd6e65fee5213baf3eaf9e07a)
Subtarget xrx200_legacy supports only a few devices. They all use
the integrated Lantiq GSWIP switch and lantiq xway PHYs. The atheros
and icplus PHYs can be safely disabled.
Switches used by individual devices are listed below.
lantiq: xrx200: add alternative names for Plusnet Hub One and BT Business Hub 5A
The Plusnet Hub One and BT Business Hub 5A have the same hardware as
the BT Home Hub 5A. This commit adds alternative names so that both
devices can be easily found in the firmware selector.
lantiq: xrx200_legacy: add alternative names for TP-Link TD-W9980(B)
The TP-Link TD-W9980(B) shares the same hardware with the TP-Link TD-W8980.
The only difference is that the TD-W8980 does not support VDSL. This is a
software limitation and once the software is changed, both work equally
supporting VDSL. This commit adds alternative names for devices so they
can be easily found in the firmware selector.
Kien Truong [Sat, 11 Jan 2025 05:20:12 +0000 (12:20 +0700)]
rockchip: disable kernel preemption
This setting is more suitable for device running OpenWRT.
Most OpenWRT targets are already default to this configuration,
and it has shown better performance in VPN (wireguard).
Updating the driver patches for ipq40xx (correctly) removed the
ethernet0 alias from qcom-ipq4019.dtsi; however, on some devices this
alias is needed for the bootloader to set MAC addresses in the FDT.
As it is unknown which devices actually need the alias, simply add it to
all devices trees for now that enable the &gmac now to avoid regressions
from previous OpenWrt releases. The additional alias should not cause any
issues even when it is not needed.
A TODO comment is added to the same Device Trees to document that the
alias may not be needed (hopefully preventing it from being copied
unnecessarily to newly added devices in the future). The following
devices are known to need the alias for correct MAC address assignment,
so no TODO comment is added:
This patch is needed on bmips since it fixes issues with GPIOs not being
properly configured due to gpio_request_enable not being called on bcm63xx
devices. Therefore we can now drop the bcm63268 gpio function patch.
David Bauer [Sun, 22 Dec 2024 01:56:12 +0000 (02:56 +0100)]
mac80211: set basic-rate for mesh interfaces
Basic rates were not set for mesh-interfaces, resulting in the undesired
behavior where 11s frames might be sent with a rate which was not
configured.
Depending on the driver, the basic rate might also be used to determine
the beacon rate configured to the chip. One such example are MediaTek
MT7915 platforms.
Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com
Roland Reinl [Wed, 18 Dec 2024 14:45:37 +0000 (15:45 +0100)]
mediatek: Fix U-Boot variables handling for D-Link M30 A1
I think I implemented the U-Boot handling incorrectly on M30 (saw the issue while porting M60 to OpenWrt). Maybe someone with more U-Boot experience can have a look at it.
What I understood until now:
Before flashing, `sw_tryactive` must be set to 0 because OpenWrt runs on partition 0
During reset after flashing, U-Boot executes the following line:
`boot_rd_auto_sw_img=if itest.s ${sw_tryactive} == 2; then run boot_by_part; else run boot_by_tryactive; fi`
As `sw_tryactive` was set to 0 before flashing, `boot_by_tryactive` will be executed:
`boot_by_tryactive=if itest.s ${sw_tryactive} == 0; then setenv sw_tryactive 2; setenv sw_active 1; saveenv; run ub0; else setenv sw_tryactive 2; setenv sw_active 2; saveenv; run ub1; fi`
As `sw_tryactive` was set to 0 before flashing, `sw_active` will be set to 1 and `ub0` will be executed:
`ub0=setenv bootpart 0; mtkboardboot; run ub0to1; uip main; reset`
If the OpenWrt boot is successful, `ub0to1` and `uip` main will never be executed. Only in case OpenWrt cannot be loaded, `mtkboardboot` will return and the fallback `ub0to1` is executed.
Conclusion: It's sufficient to set `sw_tryacitve` to 0 before flashing, the added code in `target/linux/mediatek/filogic/base-files/etc/init.d/bootcount` is useless.
In the worst case (/proc/cmdline doesn't contain `bootpart=ubi0` as expected), the bootpart variable would be set to 1 and causes starting the firmware from the second partition instead of the one on the first partition.
Sander Vanheule [Wed, 1 Jan 2025 21:18:05 +0000 (22:18 +0100)]
realtek: trim default package selection
Images for certain devices are staring to become too large, as some
device only have 6MB available in their vendor partition layout for the
initial install. This is especially pressing for bootloaders only
supporting gzip compression.
Drop some packages from DEFAULT_PACKAGES that aren't strictly required
for a factory install. The user can always install more packages later
using opkg/apk, or via a sysupgrade to a custom build.
firewall4 is kept to ensure the most recent firewall package is selected
in builds including LuCI.
ethtool is kept as a frequently used diagnostics tool.
Linus Walleij [Thu, 2 Jan 2025 14:44:45 +0000 (15:44 +0100)]
ath79: Push MV88E6060 DSA switch into package
We can use a package for the MV88E6060 DSA switch on the single
ath79 device that uses it, saving around 600 KB of memory on
all other devices (for the DSA infrastructure, mainly).
As far as I can see the TP-Link TL WR941 v2 is the only device
using MV88E6060 and the only device with a DSA switch overall.
However the ath79 people should look at this so I'm not
mistaken.
Linus Walleij [Fri, 27 Dec 2024 23:13:37 +0000 (00:13 +0100)]
ixp4xx: Break out mv88e6060 DSA switch to package
Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.
The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.
lantiq: xrx200: add support for lan3 and lan4 on AVM 5490/5491
On the AVM 5490/5491, lan1, lan2 and wan ports are connected directly
to the internal GSWIP switch. The lan3 and lan4 ports are connected via
an external QCA8334 switch. This commit adds the missing entries in dts
and adds the driver module.
Shiji Yang [Fri, 13 Dec 2024 05:30:38 +0000 (13:30 +0800)]
base-files: enable get_mac_ascii() to handle redundant strings
The function get_mac_ascii() will fail when there are two or more
same MAC address variable names in the mtd partition. Only retain
the first variable to workaround this rare situation.
Shiji Yang [Sat, 21 Dec 2024 16:31:06 +0000 (00:31 +0800)]
uboot-mediatek: add missing LED command for OpenWrt One
The u-boot LED command "led_loop_done" is missing from the OpenWrt
One NAND flash u-boot. Copy it from the OpenWrt One NOR flash u-boot
default environment to fix this issue.
Shiji Yang [Wed, 1 Jan 2025 08:17:08 +0000 (16:17 +0800)]
ramips: make package kmod-sdhci-mt7620 conflict with kmod-mmc-mtk
These two packages are SDXC drivers for Mediatek mt762x series SoCs.
One is upstream implementation, and the other is downstream driver.
Installing them together will result in conflicts.
Shiji Yang [Sat, 13 Jul 2024 03:32:45 +0000 (11:32 +0800)]
ramips: mmc-mtk: add more vendor driver register init values
In the MTK vendor driver, mt762x SDXC registers MSDC_PATCH_BIT and
MSDC_PATCH_BIT1 have different init values than upstream driver.
These magical values should have some help for the stability.
Shiji Yang [Wed, 25 Dec 2024 12:33:23 +0000 (20:33 +0800)]
ramips: mt762{0,8}: reduce default MMC clock to 24 MHz
The upstream mtk-sd driver did not perform specific timing
optimization for MT762x series SoC, hence the SDHC peripheral
of some boards cannot run at too high frequency. Reduce the
maximum clock frequency to fix the mmc read/write error.
John Audia [Thu, 2 Jan 2025 12:50:26 +0000 (07:50 -0500)]
bcm27xx/bcm2712: Fix-up RP1 modules
Correct a few mistakes around dependencies and naming and unset
CONFIG_FIRMWARE_RP1 in RPi5B's config and instead of a builtin, build it
as a module.
Without this change, there are two entries for rp1.ko in
/lib/modules/$(uname -r)/modules.builtin due to how we strip the leading
directories when we generate it. See: package/kernel/linux/Makefile
around line 63.
Felix Fietkau [Sat, 4 Jan 2025 10:54:22 +0000 (11:54 +0100)]
mt76: update to Git HEAD (2025-01-04)
35bcf68a6297 wifi: mt76: scan: fix setting tx_info fields 4d8d6e2e7710 wifi: mt76: scan: set vif offchannel link for scanning/roc e354436db440 wifi: mt76: mt7996: use the correct vif link for scanning/roc
7a3bcd39ae1f r8169: use helper r8169_mod_reg8_cond to simplify rtl_jumbo_config e3e9e9039fa6 r8169: align WAKE_PHY handling with r8125/r8126 vendor drivers 330dc2297c82 r8169: improve rtl_set_d3_pll_down c507e96b5763 r8169: improve __rtl8169_set_wol 83cb4b470c66 r8169: remove leftover locks after reverted change 2cd02f2fdd8a r8169: improve initialization of RSS registers on RTL8125/RTL8126 a3d8520e6a19 r8169: align RTL8126 EEE config with vendor driver 4af2f60bf737 r8169: align RTL8125/RTL8126 PHY config with vendor driver eb90f876b796 r8169: align RTL8125 EEE config with vendor driver b8bd8c44a266 r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats f75d1fbe7809 r8169: add support for RTL8125D c4e64095c00c r8169: enable EEE at 2.5G per default on RTL8125B d64113c6bb5e r8169: remove rtl_dash_loop_wait_high/low 1c105bacb160 r8169: avoid duplicated messages if loading firmware fails and switch to warn level ac48430368c1 r8169: don't take RTNL lock in rtl_task() e3fc5139bd8f r8169: implement additional ethtool stats ops b8bf38440ba9 r8169: enable SG/TSO on selected chip versions per default 854d71c555df r8169: remove original workaround for RTL8125 broken rx issue 1ffcc8d41306 r8169: add support for the temperature sensor being available from RTL8125B
The following patches require backporting additional linux patches: e2015942e90a r8169: replace custom flag with disable_work() et al e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Hauke Mehrtens [Sun, 22 Dec 2024 16:33:21 +0000 (17:33 +0100)]
mbedtls: Deactivate ARIA block cipher by default
The ARIA block cipher is pretty uncommon in TLS, deactivate it for now.
This saves some space and reduces the possible variations and attack
vectors of mbedtls.
ARIA support was deactivated in OpenWrt 23.05 by default.
Tianling Shen [Fri, 3 Jan 2025 12:37:41 +0000 (20:37 +0800)]
rockchip: fix phy reset on rk356x
The commit 7160820d742a ("phy: rockchip: naneng-combphy: fix phy reset")
was backported to kernel 6.6 branch by upstream, however the correspond
dtsi fixes was not, resulting the following error:
```
[ 0.225521] rockchip-naneng-combphy fe830000.phy: error -ENOENT: failed to get phy reset
[ 0.227467] rockchip-naneng-combphy fe840000.phy: error -ENOENT: failed to get phy reset
```
Felix Fietkau [Fri, 3 Jan 2025 19:22:13 +0000 (20:22 +0100)]
kernel: add workaround for page_pool_release warnings
defer_list skbs held by NAPI can block releasing page pools.
Work around this by scheduling rx softirq on all CPUs while trying to release
a page pool.
Robert Marko [Sat, 23 Nov 2024 13:29:49 +0000 (14:29 +0100)]
config: rename SECCOMP to USE_SECCOMP
It seems that we have some kind of a symbol name conflict which causes
CONFIG_SECCOMP to always be read as y.
Unfortunatelly, I could not figure out what is causing this, but simply
renaming SECCOMP to USE_SECCOMP seems to properly work and leaves the
symbol unset unless arch dependencies are satisfied.
This fixes qoriq and others that dont support seccomp from failing due
to procd-seccomp package being selected to get included but it cannot be
built for them:
ERROR: unable to select packages:
procd-seccomp (no such package):
required by: base-files-1637~52b6c92479[procd-seccomp]
Petr Štetiar [Sun, 17 Nov 2024 05:15:13 +0000 (05:15 +0000)]
linux: fix missing default packages in profiles.json
Robert reported, that in firmware images generated by ASU, there is
`apk` package manager missing after the commit 44598c233dd9 ("build:
remove broken dependency of metadata on toplevel .config variables").
That is happening, because apk got removed from `default_packages` list in
`profiles.json`, which is being generated by `json_overview_image_info` Make
target, which uses `scripts/json_overview_image_info.py` helper script,
which gets the information from `DEFAULT_PACKAGES` Make variable.
So lets fix it by providing `DEFAULT_PACKAGES` variable when its needed.
The reason why we didn't added those packages as a dependency to
base-files like any other packages, was to allow disabling them (in
order to save space).
Fixes: #16969 Fixes: openwrt/asu/issues/1084 Fixes: 44598c233dd9 ("build: remove broken dependency of metadata on toplevel .config variables") Reported-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz> Link: https://github.com/openwrt/openwrt/pull/16986 Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 90f0be8521a8608b0932c1ccb747c0ef1a085910)
Felix Fietkau [Wed, 13 Nov 2024 06:04:31 +0000 (07:04 +0100)]
build: fix including busybox, procd and apk/opkg in imagebuilder
Since the image builder pulls package lists from metadata directly,
add procd and busybox as depdendencies to base-files.
As for the package manager itself, since it can be disabled it needs
to be added directly in the image builder makefile
Fixes: 44598c233dd9 ("build: remove broken dependency of metadata on toplevel .config variables") Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 4c65359af49b6ccecd98987f842db5eba985f64b)
projects / thirdparty / openwrt.git / log
