Thanks to
https://forum.openwrt.org/t/zyxel-gs1900-10hp-revision-b1-support-openwrt-firmware/131841/32
for putting me on the right track for this problem
Error that is being fixed - running fw_printenv results in:
"Warning: Bad CRC, using default environment"
and not showing boardmodel
Workaround, manually changing /etc/fw_env.config to
"/dev/mtd1 0x0 0x400 0x10000"
Felix Fietkau [Wed, 12 Feb 2025 10:54:59 +0000 (11:54 +0100)]
hostapd: fix sta psk index for dynamic psk auth
Depending on the config / circumstances, the get_psk call can be called
multiple times from differnt places, which can lead to wrong sta->psk_idx
values. The correct call is the one that is also interested in the vlan_id,
so use the vlan_id pointer as indication of when to set sta->psk_idx.
Also fix off-by-one error for secondary PSKs
Fixes: b2a2c286170d ("hostapd: add support for authenticating with multiple PSKs via ubus helper") Signed-off-by: Felix Fietkau <nbd@nbd.name>
Shiji Yang [Sat, 25 Jan 2025 11:16:48 +0000 (19:16 +0800)]
uboot-mediatek: enable auto switch chip detect for Xiaomi AX3000T
The Xiaomi AX3000T has two hardware revisions. One uses MT7531
switch, and the other uses AN8855 switch. Set "mediatek,switch"
property to "auto" to be compatible with different switches.
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com> Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Some patches have been manually rebased to match the upstream
changes. This patch also fixes the dtc warning for reserved-memory
dts node. If #address-cells and #size-cells are not same as the
root node definitions, the dtc will complain about it.
All defconfigs are refreshed by `make "$board"_defconfig` and
`make savedefconfig`.
Evan Jobling [Thu, 23 Jan 2025 00:13:35 +0000 (00:13 +0000)]
realtek: HPE 1920-48G-PoE: allow fan speed control
The JG928A has an RTL8231 on the aux mdio bus. Add it to dts to expose
the GPIO pins used to control and monitor the fan speed. To enable speed
control, add the appropriate kernel driver module to DEVICE_PACKAGES.
Of note, this does not control all fans for the unit. The power supply
fans are not controlled.
Robert Marko [Sat, 8 Feb 2025 13:06:30 +0000 (14:06 +0100)]
qualcommax: drop the fake IPQ5018 SNAND compatible
Devices that rely on faking the NAND controler compatible for U-Boot
to patch the nodes should add it in their DTS directly, this does not
belong in the SoC DTSI.
Robert Marko [Fri, 7 Feb 2025 09:12:25 +0000 (10:12 +0100)]
qualcommax: ipq50xx: refresh kernel config
Refresh the ipq50xx kernel config as it looks like it was created by hand
instead of kernel_menuconfig so we have stuff like DWC3 which is packaged
as a kmod in a generic way, QMI helpers are part of backports etc.
This commit fixes nmbm configuration mismatch error on Xiaomi AX3000t
with Winbond W25N01KVZEIR spi-nand:
'''
[ 0.786783] NMBM configuration mismatch
'''
Root cause:
1. U-Boot W25N01KV spi-nand driver ia compiled with 64B OOB size for the
chip and store this size in the nmbm signature;
2. Linux W25N01KV driver use 96B OOB.
The change doesn't affect AX3000t variants with other spi-nand chips
(ESMT, Foresee) because their Linux drivers use 64B OOB.
Fixes: openwrt#16972 Tested-by: Aleksandr Danilov <sc16me@gmail.com> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> Link: https://github.com/openwrt/openwrt/pull/17549 Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds new "mediatek,bmt-mtd-overridden-oobsize" property. The
property helps avoid "NMBM configuration mismatch" error if mtd "OOB size"
is not equal to the "spare size" which is stored in the nmbm signature.
Robert Marko [Thu, 6 Feb 2025 11:39:26 +0000 (12:39 +0100)]
libiwinfo: update to Git HEAD (2025-02-06)
9ff15f7ee3a0 devices: add device id for MediaTek MT7992E 94b3a3c1a6c4 devices: add device id for Qualcomm Atheros IPQ5018 9cec6b4dd2df devices: add device id for Qualcomm Atheros QCN6122
Chukun Pan [Mon, 20 Jan 2025 15:10:36 +0000 (23:10 +0800)]
tools: add xxhash package for ccache
The ccache build requires xxhash, which is download from
the Internet. So add host-build package for xxhash.
Fixes: #16851 Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
[ use git source proto ] Link: https://github.com/openwrt/openwrt/pull/17700 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
qualcommax: ipq50xx: add support for Linksys MX2000 and MX5500
Add support for Linksys MX2000 (Atlas 6) and MX5500 (Atlas 6 Pro).
These devices are completely identical except for the secondary wifi
chip used for 5Ghz: QCN6102 is used on MX2000 while QCN9024 is used
on MX5500
Flash instructions (in case of MX2000, else replace with MX5500 images):
1. On OEM firmware, login to the device (typically at http://192.168.1.1) and click 'CA'
in the bottom right corner -> Connectivity -> Manual Upgrade. Alternatively, browse to
http://<router IP>/fwupdate.html.
Upgrade firmware using openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin image.
Optionally install on second partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
MX2000: https://support.linksys.com/kb/article/585-en/
MX5500: https://support.linksys.com/kb/article/587-en/
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MX2000_1.1.7.210469_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MX2000_1.1.7.210469_prod.img kernel
QCN6122 is a PCIe based solution that is attached to and enumerated
by the WPSS (Wireless Processor SubSystem) Q6 processor.
Though it is a PCIe device, since it is not attached to APSS processor
(Application Processor SubSystem), APSS will be unaware of such a decice
and hence it is registered to the APSS processor as a platform device(AHB).
Because of this hybrid nature, it is called as a hybrid bus device.
As such, QCN6122 is a hybrid bus type device and follows the same codepath
as for WCN6750.
This is a reversed engineered and heavily simplified version of below
downstream patch:
https://git.codelinaro.org/clo/qsdk/oss/system/feeds/wlan-open/-/ \
blob/NHSS.QSDK.12.4.5.r2/mac80211/patches/232-ath11k-qcn6122-support.patch
Co-developed-by: George Moussalem <george.moussalem@outlook.com> Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org> Signed-off-by: George Moussalem <george.moussalem@outlook.com> Link: https://github.com/openwrt/openwrt/pull/17182 Signed-off-by: Robert Marko <robimarko@gmail.com>
Add ability to download and package ath11k firmware for QCN6122.
QCN6122 is specific/exclusive to the IPQ5018 platform and firmware
files are publishes in a subdirectory of the IPQ5018 firmware files.
While at it, add support for packaging BDFs for QCN6122 wifi and
update iwinfo to recognize QCN6122 wifi.
mac80211: ath11k: Support setting bdf-addr and caldb-addr via DT
IPQ5018 uses different BDF and caldb addresses for vairous boards,
so let's support reading these addresses from the device tree.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com> Signed-off-by: George Moussalem <george.moussalem@outlook.com> Link: https://github.com/openwrt/openwrt/pull/17182 Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com> Signed-off-by: George Moussalem <george.moussalem@outlook.com> Link: https://github.com/openwrt/openwrt/pull/17182 Signed-off-by: Robert Marko <robimarko@gmail.com>
Add ability to download and package ath11k firmware for IPQ5018.
As part of commit 172ccf7, the source is pointed to the new QCA repo.
Until QCA publishes updated firmware for IPQ5018 and QCN6122, we need
to download the firmware from the old QUIC repo. As such, add a new
download routine for IPQ5018/QCN6122 to fetch the firmware files from
the old repo.
While at it, add support for packaging BDFs for IPQ5018-based boards
and update iwinfo to recognize IPQ5018 wifi.
Introduce support for the Qualcomm IPQ50xx SoC.
This series adds support for the following components:
- minimal boot support: GCC/pinctrl/watchdog/CPUFreq/SDI (upstreamed)
- USB2 (upstreamed)
- Thermal/Tsens
- PCIe gen2 1&2-lane PHY and controller
- PWM and PWM LED
- QPIC SPI NAND controller
- CMN PLL Block (provider of fixed rate clocks to GCC/ethernet/more.)
- Ethernet: IPQ5018 Internal GE PHY (1 gbps)
- Remoteproc MPD driver for IPQ5018 (2.4G) & QCN6122 (5/6G) Wifi
Co-developed-by: Ziyang Huang <hzyitc@outlook.com> Signed-off-by: Ziyang Huang <hzyitc@outlook.com> Signed-off-by: George Moussalem <george.moussalem@outlook.com> Link: https://github.com/openwrt/openwrt/pull/17182 Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the Qualcomm IPQ50xx in the QCA NSS dataplane driver.
The QCA implementation uses depracated DMA api calls and a downstream SCM
call, so convert to proper Linux DMA and SCM api calls.
In addition, add fixed-link support to support SGMII which is used to
connect the internal IPQ50xx switch to an external switch (ex. QCA8337)
Co-developed-by: Ziyang Huang <hzyitc@outlook.com> Signed-off-by: Ziyang Huang <hzyitc@outlook.com> Signed-off-by: George Moussalem <george.moussalem@outlook.com> Link: https://github.com/openwrt/openwrt/pull/17182 Signed-off-by: Robert Marko <robimarko@gmail.com>
Michael Heimpold [Thu, 28 Nov 2024 07:00:36 +0000 (08:00 +0100)]
mxs: adapt default package list for Duckbill devices
Replace outdated package names, order the remaining.
firewall4 is added again, since it is enabled by default.
The device is not a router by default, so this package
makes no sense in the default config. User can enable it
by theirself, or it will be automatically pulled via
dependency, e.g. luci-app-firewall.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Michael Heimpold [Sun, 15 Sep 2024 08:39:40 +0000 (10:39 +0200)]
mxs: fix image generation for I2SE Duckbills
The standard U-Boot boot scripts for Duckbills expect the
Linux kernel and device tree files installed below /boot
within the (ext4) root filesystem.
Also a raw zImage is expected instead of uImage.
Extend the SD card generation accordingly and while at,
install all possible Duckbill DT blobs there.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Sander Vanheule [Tue, 28 Jan 2025 07:14:03 +0000 (08:14 +0100)]
realtek: drop old RTL8231 driver
The old RTL8231 driver integrated the MDIO bus access with the GPIO
control ops, making this driver not very portable to newer platforms.
It depended on the SoC ID instead of the compatible to determine the
MDIO access register, further complicating portability.
A new MFD driver is now available, which offers proper pin config as
well as optional LED support, which can work on any (bitbanged) MDIO
bus. Now that all devices have been migrated, we can drop the old code.
Chuanhong Guo [Tue, 14 Jan 2025 06:36:36 +0000 (14:36 +0800)]
siflower: sf21: add support for Bananapi BPI-RV2
Specification:
- Siflower SF21H8898
- 512MB DDR3, 128MB SPI-NAND and 16MB SPI-NOR
- 5x Gigabit ports (SF23P1240 QSGMII PHY and SF23P1211F RGMII PHY)
- 1x 2.5G port (Airoha EN8811H PHY)
- M.2 Key B slot with USB2.0, PCIEx1 and a NanoSIM card slot
- MiniPCIe slot with USB2.0 and PCIEx1
- 1x USB2.0 port through USB Hub
- PCF8563-compatible RTC
The SoC can only boot from SPI0. Two SPI flash chipselects are connected
to GPIO5 (SPI0 CS) and GPIO36 through a 2x2 jumper. It boots from
SPI-NOR or SPI-NAND depending on how the jumpers are connected.
The firmware can be flashed using U-boot web recovery from Siflower
vendor U-boot.
Chuanhong Guo [Tue, 8 Oct 2024 06:16:15 +0000 (14:16 +0800)]
siflower: add ngpios property to gpio-siflower
The same GPIO controller is found on all current Siflower SoCs,
with different number of GPIOs. Add ngpios property instead of
specifying it with dt match data.
Paul Spooren [Sat, 1 Feb 2025 23:01:58 +0000 (23:01 +0000)]
build: lock versions for special APK packages
The three packages base-files, libc and kernel are special, the former
can't be upgraded in place since it's content are modified on startup,
the latter two are virtual packages only used as constraints for the
package manager.
Historically base-files was "locked" via a special OPKG function, the
latter two were hidden from the package index and thereby never picked
as possible upgrade.
Time moved forward and we now have APK and tools like OWUT. The latter
compares available packages with installed packages and generates user
readable output, requiring versions for libc and kernel, too. At the
same time, APK uses a different looking mechanism, which is set during
installation instead of part of the package metadata.
In short, this patch adds version constraints to the three packages,
allowing them to be part of the package index.
Fixes: #17774 Fixes: #17775 Fixes: efahl/owut#31 Signed-off-by: Paul Spooren <mail@aparcar.org>
It looks like the eeprom gets broken after this change.
I think this change was not tested on a real device before it was
merged.
The MAC addresses will be broken again after this revert.
ipq806x: make use of ASCII env NVMEM driver for Linksys EAX devices
Make use of ASCII env NVMEM driver for Linksys EAX devices. This also
fix a problem with Linksys EAX devices where the 2 MAC interface had the
same MAC address causing a conflicts with FDB entry. This got much more
present with the DSA conversion making the system not usable.
To fix this, increment + 1 the MAC address for the WAN interface.
generic: add pending support for NVMEM ASCII ENV layout driver
Add pending patch to support NVMEM ASCII ENV layout driver. This is a
generic driver to handle simple NVMEM partition that store environment
in a simple text format. This is the case for Linksys devinfo partition
that are litterally txt file with format "name=value\n"
Such driver works similar to u-boot,env with a similar format. While at
it also introduce a patch to generalize mac-base handling for also other
layout driver.
ipq806x: fix broken WAN on Linksys EAX and Asrock G10
Fix broken WAN on Linksys EAX and Asrock G10 by incrementing the WAN
interface MAC address + 1. This caused conflicting entry in the FDB
table and caused the WAN port to malfunction with the DSA conversion.
Daniel Golle [Sat, 1 Feb 2025 05:03:50 +0000 (05:03 +0000)]
mediatek: mt7622: fix SATA on BPi-R64
Two commits which made their way into Linux stable broke the SATA
support on the BPi-R64.
Fix this by reverting a node rename which broke DT-overlay application
and import a (still pending) patch re-adding the 'syscon' compatible to
the pciesys clock-controller which also contains phy-mode bits
referenced by the ahci_mtk driver expecting to access them using
syscon_regmap_lookup_by_phandle().
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes: eaa82118eadf ("mvebu: Switch to use a module for mv88e6xxx") Signed-off-by: Kabuli Chana <newtownBuild@gmail.com> Link: https://github.com/openwrt/openwrt/pull/17793 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
b11bff90f2ad r8169: add support for RTL8125BP rev.b b3593df26ab1 r8169: add support for RTL8125D rev.b b299ea006928 r8169: adjust version numbering for RTL8126 bb18265c3aba r8169: remove support for chip version 11 2e20bf8cc057 r8169: remove unused flag RTL_FLAG_TASK_RESET_NO_QUEUE_WAKE e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
mediatek: filogic: fix 2.5G phy compatible for WR3000H
Following the initial support of the Cudy WR3000H with PHY C22 for the 2.5G WAN
interface, several improvements fixing issues with RealTek RTL8221B PHYs have
been merged.
Therefore we can now bring the DT in line with other equipment and declare the
2.5G WAN PHY as C45.
Fixes: 9d66b8b ("mediatek: filogic: Add support for cudy wr3000h") Signed-off-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com> Link: https://github.com/openwrt/openwrt/pull/17739
[reword commit description] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Daniel Golle [Thu, 30 Jan 2025 05:49:43 +0000 (05:49 +0000)]
generic: net: phy: realtek: work-around hang on SerDes setup
On some but not all devices using the RTL8221B 2.5GBit/s PHY the SerDes
setup sequence may hang under some circumstances (eg. <2500M link
partner present during boot).
Work-around the issue by performing a hardware reset and subsequent
retry of the SerDes setup, which seems to always succeed.
Doing this requires moving ALDPS setup to config_init (which is anyway
the better place for that) as it otherwise doesn't survive the reset.
Also disable listening on MDIO address 0 which may be used by other PHYs
despite being spec'ed as "broadcast address", as bus activity on address
0 may otherwise confuse the RealTek PHY for good reasons.
Tested-by: Luis Mita <luis@luismita.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Wed, 29 Jan 2025 19:09:54 +0000 (19:09 +0000)]
config: add VERSION_FIRMWARE_URL
This new value points to where firmware can be downloaded. It's not
about a single release but all available firmware releases.
In the next step, this URL should be exposed via `ubus call system
board` as an entry of the `distribution` field. With that value, the
running firmware can check for newer releases.
We already have VERSION_REPO however that's different and only meant for
package managers to download their fitting package indexes/packages.
Jan Hoffmann [Thu, 30 Jan 2025 09:40:25 +0000 (10:40 +0100)]
mediatek: fix TUF-AX4200 WAN LED
With the current LED configuration using "mxl,led-config", the WAN LED
stops working after the interface is brought down and up again.
Since the driver also properly supports PHY LEDs now, switch to that
instead. This makes the LED work properly, but requires configuration
from userspace.
Hauke Mehrtens [Wed, 29 Jan 2025 22:37:34 +0000 (23:37 +0100)]
x86: Add kmod-drm-i915 as default package
Add kmod-drm-i915 to the default packages. It was build into the kernel
before and is now build as a kernel module.
Fixes: 77cfe8fd15d3 ("x86: make i915 as a kmod with required firmware") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Link: https://github.com/openwrt/openwrt/pull/17781 Signed-off-by: Robert Marko <robimarko@gmail.com>
Paweł Owoc [Thu, 2 Jan 2025 21:31:33 +0000 (22:31 +0100)]
qualcommax: ipq807x: Remove OEM UBI volume before upgrade for Linksys MX devices
Use 'remove_oem_ubi_volume' function to remove OEM UBI volume before upgrade.
This allows to upgrade even if we have OEM firmware on the second partition.
Applies to Linksys MX4200/MX4300/MX5300/MX8500.
Paweł Owoc [Sat, 24 Feb 2024 19:47:58 +0000 (20:47 +0100)]
qualcommax: ipq807x: Add ability to perform upgrade on current partition for Linksys MX devices
Dual firmware devices like Linksys MX4200, MX4300, MX5300 and MX8500 use separate rootfs partition.
This option helps to keep all configuration during upgrade.
Paweł Owoc [Sat, 24 Feb 2024 19:25:43 +0000 (20:25 +0100)]
base-files: sysupgrade: Add new option -s to perform upgrade on current partition
Add new option to be able to perform upgrade on current partition for dual firmware devices:
"-s stay on current partition (for dual firmware devices)"
Sander Vanheule [Mon, 27 Jan 2025 21:17:57 +0000 (22:17 +0100)]
realtek: add PoE enable line to Netgear GS110TPP
By switching to the new RTL8231 driver in commit b7af54d5c18c ("realtek:
Simple conversions to RTL8231 MFD driver"), the bootloader state of the
RTL8231's pins is now maintained. As the bootloader de-asserts the PoE
enable signal, this means PoE output is no longer available.
Add a gpio-hog with high output, restoring the line value from when the
pin was configured (by default) as an input with a pull-up resistor.
This will hard-enable the PoE output, but the individual ports can still
be administratively disabled by realtek-poe or a similar tool.
Switch the implementation for the RTL8231 GPIO expander to the new
driver.
This allows specifying the GPIO driving the RTL8231's reset as a proper
MDIO reset line, so the gpio-hog can be dropped. Since it was pinned at
a high level, the reset line is actually active-low (i.e. high when not
in reset).
Sander Vanheule [Sun, 12 Jan 2025 16:57:33 +0000 (17:57 +0100)]
realtek: switch RTL8231 driver for D-Link DGS-1210
Update the common external GPIO DTSI file for the DGS-1210 devices to
use an MDIO device on the auxilairy MDIO bus, as the original driver was
doing behind the screen.
Switching to the new driver will allow for full pin-control and will no
longer reset pin config set by the bootloader.
Sander Vanheule [Sun, 12 Jan 2025 16:53:34 +0000 (17:53 +0100)]
realtek: Switch DGS-1210-10P DTS to gpio.dtsi
The DTS file for the DGS-1210-10P is slightly different from the other
DGS-1210 devices, in that it didn't specify a gpio-restart node when it
was added. The gpio-restart has been found to work on the DGS-1210-10P
as well, so switch it over to the common definitions.
This converts the last device from the product family to the common
definition for the (external) GPIOs.
Tested-by: Michel Thill <jmthill@gmail.com> Signed-off-by: Sander Vanheule <sander@svanheule.net>
Sander Vanheule [Sat, 18 Jan 2025 15:51:59 +0000 (16:51 +0100)]
realtek: Drop unused property on DGS-1210 gpio0
The 'indirect-access-id' property on gpio0 is a remnant from the
original GPIO driver. This property has not been relevant on the SoC's
embedded GPIO controller for a long time, so just drop it.
Uwe Kleine-König [Mon, 27 Jan 2025 15:12:23 +0000 (16:12 +0100)]
dnsmasq: add fix related to DNSSEC verification from upstream
To find the DS record for a given zone the parent zone's nameserver must
be queried and not the nameserver for the zone. Otherwise DNSSEC
verification for unsigned delegations breaks.
Hauke Mehrtens [Mon, 27 Jan 2025 00:09:33 +0000 (01:09 +0100)]
apm821xx: NETGEAR WNDR4700: Fix compat version
The definition for the netgear_wndr4700 had two different
DEVICE_COMPAT_VERSION definitions.
In commit 5815884c3a2 ("apm821xx: migrate to DSA"), an additional
DEVICE_COMPAT_VERSION := 3.0 attribute was added to the device
definition. The old one with version 2.0 stayed and was defined later
overwriting the new one.
Replace the old version 2.0 with the new version 3.0
Robert Marko [Mon, 27 Jan 2025 13:25:09 +0000 (14:25 +0100)]
generic: add missing CONFIG_LEDS_ST1202 symbol
ST1202 controller was added recently, but it was not disabled in the
generic config, so lets avoid individual target configs disabling it
and just disable it in generic config.
airoha: an7581: replace eMMC support with upstream version
Replace eMMC support with upstream version where we declare dummy clock
and dummy regulator instead of a specific compatible. Also drop the
downstream patch for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ramips: restore full switch performance for USW-Flex
Since commit f1c9afd80138 ("ramips: mt7621-dts: mux phy0/4 to gmac1") the
USW-Flex lan1 port has been attached directly to the CPU. This improves
routing performance but hinders switching.
This is a generally accepted trade-off in that commit but for USW-Flex it
is a questionable choice. This switch is designed to deliver PoE to remote
places and using it as a router is unlikely. Meanwhile, the lan1 port is
also PoE-in and will often be the uplink, carrying most of the traffic.
Reverting f1c9afd80138 for USW-Flex restores full 1 Gbps switching
performance on all ports.
Tim Harvey [Tue, 17 Dec 2024 22:52:48 +0000 (14:52 -0800)]
imx: 6.6: add a patch to work around a PCI init hang on IMX8M{M,P}
The act of attempting link at gen1 then trying to link at higher speeds
causes a hang with the specific PCIe switch used on the Gateworks Venice
boards. Work around this by linking at the highest speed first as is
common with all other PCI controller drivers.
projects / thirdparty / openwrt.git / log
