openssl: add package for openssl.cnf, misc changes
- Add the /etc/ssl/openssl.cnf as a separate package, to avoid breaking
the transitional mechanism, allowing libopenssl_1.0* and
libopenssl_1.1* to coexist.
- Remove the (selecting) dependency on @KERNEL_AIO
- Use global SOURCE_DATE_EPOCH
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Add a patch to enable the option to change the default ciphersuite list
ordering to prefer ChaCha20 over AES-GCM. This is used by default for
all platforms, except for x86_64 and aarch64. The assumption is that
only the latter have AES-specific CPU instructions and asm code that
uses them in openssl. Chacha20Poly1305 is 3x faster than AES-256 in
systems without AES instructions, with an equivalent strength.
Disable error messages by default except for devices with small flash or
RAM, to aid debugging.
Disable ASM by default on arm platform with small flash. Size
difference on mips and powerpc, the other platforms with small flash
devices, are not really relevant (using 100K as a threshold). All of
the affected platforms are source-only anyway.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
This version adds the following functionality:
* TLS 1.3
* AFALG engine support for hardware accelleration
* x25519 ECC curve support
* CRIME protection: disable use of compression by default
* Support for ChaCha20 and Poly1305
Patches fixing bugs in the /dev/crypto engine were applied, from
https://github.com/openssl/openssl/pull/7585
This increses the size of the ipk binray on MIPS32 by about 32%:
old:
693.941 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk
193.827 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk
Adds the following configuration options:
* using optimized assembler code (was always on before)
* use of x86 SSE2 instructions
* dyanic engine support
* include error messages
* Camellia, Gost, Idea, MDC2, Seed & Whirlpool algorithms
* RFC3779, CMS protocols
* VIA padlock hardware acceleration engine
Installs openssl.cnf with the library as it is used by engines
independent of the openssl util.
Fixes DTLS option that was innefective before.
Disables insecure SSL3 protocol and SHA0.
Adds openwrt-specific targets to Configure script, including asm support
for i386, ppc and mips64.
Strips building dirs from CFLAGS shown in binary.
Skips the fuzz directory during build.
Removed include/crypto/devcrypto.h that was included here, to use the
cryptodev-linux package, now that it was been moved from the packages
feed to the main openwrt repository.
This decreses the size of the ipk binray on MIPS32 by about 3.3%:
old:
706.957 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk
199.294 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk
Felix Fietkau [Tue, 12 Feb 2019 15:37:30 +0000 (16:37 +0100)]
base-files: fix ucert verification
ucert needs to check the firmware part with metadata, but without the signature.
Use the new fwtool mode to extract that without altering the firmware image inside
the check
Tony Ambardar [Fri, 14 Dec 2018 07:49:32 +0000 (23:49 -0800)]
iproute2: tc: reduce size of dynamic symbol table
In the case of SHARED_LIBS=y, don't use -export-dynamic to place *all*
symbols into the dynamic symbol table. Instead, use --dynamic-list to
export a smaller set of symbols similar to that defined in static-syms.h
in the case of SHARED_LIBS=n, avoiding an 11 KB tc package size increase.
Tony Ambardar [Thu, 13 Dec 2018 19:48:55 +0000 (11:48 -0800)]
iproute2: tc: enable and fix support for using .so plugins
This enables using the tc module m_xt.so, which uses the act_ipt kernel
module to allow tc actions based on iptables targets. e.g.
tc filter add dev eth0 parent 1: prio 10 protocol ip \
u32 match u32 0 0 action xt -j DSCP --set-dscp-class BE
Make the SHARED_LIBS parameter configurable and based on tc package
selection.
Fix a problem using the tc m_xt.so plugin as also described in
https://bugs.debian.org/868059:
Sync include/xtables.h from iptables to make sure the right offset is
used when accessing structure members defined in libxtables. One could
get “Extension does not know id …” otherwise. (See also: #868059)
Patch to sync the included xtables.h with system iptables 1.6.x. This
continues to work with iptables 1.8.2.
Tony Ambardar [Sun, 16 Dec 2018 02:26:48 +0000 (18:26 -0800)]
iproute2: use tc package variant to limit other package sizes
Replace the old 'tc' with a singleton package variant which will be used
to enable additional functionality and limit it only to tc. Non-variant
packages will only be installed during 'tiny' variant builds, hence will
be configured without extra features, thus preserving previously limited
functionality and reduced package sizes.
Also set ip-tiny as the default variant, and install 'tiny' versions of
development libraries.
Tony Ambardar [Sat, 24 Nov 2018 07:56:24 +0000 (23:56 -0800)]
iproute2: simplify Makefile, patches and fix feature detection
Compile-based feature detection (e.g. xtables, ipset support) was broken
due to silent compilation errors in the configure script, caused by a
Makefile variable KERNEL_INCLUDE referring to kernel build headers. Use
userspace headers by setting the same "user_headers" kernel include path
as used for the iptables build.
Remove redundant or unused Build/Configure definitions from package
Makefile, including KERNEL_INCLUDE, LIBC_INCLUDE and DBM includes.
Don't pass LDFLAGS within MAKE_FLAGS as this interferes with LDFLAGS in
tc/Makefile and masks a link parameter ("-Wl,-export-dynamic"). Instead,
use standard TARGET_LDFLAGS.
Replace EXTRA_CCOPTS in MAKE_FLAGS with cleaner TARGET_CPPFLAGS, and also
drop now unneeded patch 150-extra-ccopts.patch.
Enable defining XT_LIB_DIR from Makefile, needed to set the iptables
modules directory to something other than /lib/xtables, and also add
libxtables dependency. Both are needed with working xtables detection.
Note that libxtables is also pulled in by iptables, firewall or luci, so
this change has no size impact in most cases.
Tony Ambardar [Fri, 23 Nov 2018 09:09:23 +0000 (01:09 -0800)]
iproute2: fix broken configuration patch
Since v4.13, iproute2 switched to a config.mk file with greater use of
pkg-config for library/feature detection. Replace the old Config patch
with one modifying the configure script but enabling the same changes:
- explicitly disable TC_CONFIG_ATM
- rely on feature detection for IP_CONFIG_SETNS and TC_CONFIG_XT
Tony Ambardar [Tue, 18 Dec 2018 05:29:33 +0000 (21:29 -0800)]
kernel: enable CONFIG_BPF_JIT by default
Enable the built-in BPF JIT compiler for all 4.9, 4.14 and 4.19 kernels,
which should speed up cBPF and eBPF-based packet filtering (tc, iptables)
and packet sniffing (libpcap, tcpdump, fwknopd, etc).
This has minimal kernel size impact, increasing the size of uImage-lzma
(normally ~2 MB on mips_24kc or mips64el_mips64) by 5 KB for the MIPS32
arch cBPF JIT and by 9 KB for the MIPS64 arch eBPF JIT, on kernel 4.14.
With JIT enabled (cBPF only), the standard BPF test module (test_bpf.ko)
running on a DIR-835 (mips_24kc) used 33 CPU seconds, but 68 without JIT.
This change aligns with the notion of OpenWRT as the network go-to swiss
army knife for packet handling, especially on CPU-constrained platforms.
Tony Ambardar [Mon, 19 Nov 2018 17:16:48 +0000 (09:16 -0800)]
kernel/modules: add kmod-bpf-test package
Add the test_bpf module that runs various test vectors against the BPF
interpreter or BPF JIT compiler. The module must be manually loaded, as
with the kmod-crypto-test module which serves a similar purpose.
Tony Ambardar [Tue, 30 Oct 2018 13:27:04 +0000 (06:27 -0700)]
kernel/modules: add kmod-sched-ipset package
Add em_ipset module to support tc filter classification by IP set. Build
as a standalone package to help avoid pulling in rest of kmod-sched and
isolate new dependency on kmod-ipt-ipset.
Tony Ambardar [Tue, 30 Oct 2018 12:50:51 +0000 (05:50 -0700)]
kernel/modules: kmod-sched: add some common, useful actions
Add act_pedit, act_csum, act_gact and act_simple modules for additional
tc action support. Module act_simple helps with debug and logging, similar
to iptables LOG target, while act_gact provides common generic actions.
Modules act_pedit and act_csum support general packet mangling, and have
been the subject of feature requests and forum discussions (e.g. DSCP),
as well as being added to the Turris OS fork of OpenWrt ~2 years ago.
Also select dependency kmod-lib-crc32c to support act_csum.
All tc ematch modules, including those in kmod-sched-core and kmod-sched,
use cls_basic as a core dependency. Relocate cls_basic from kmod-sched to
kmod-sched-core to avoid requiring kmod-sched unnecessarily.
This change is also backwards compatible since any past tc ematch users
will have had to install both kmod-sched-core and kmod-sched anyway.
Add the matchall kernel module cls_matchall introduced in kernel 4.8. The
matchall classifier matches every packet and allows the user to apply
actions on it. It is a simpler, more efficient replacement for the common
but cryptic tc classifier idiom "u32 match u32 0 0".
Installation
------------
1. Connect to the device via UART.
2. Interrupt the U-Boot on power-on by pressing enter when prompted.
3. Connect you computer to one of the routers LAN ports.
Assign yourself the IP 192.168.31.10/24.
Copy the OpenWRT initramfs image to a tftp server root directory.
Rename the image to 'x4q.bin'.
4. Load the initramfs image to the router by executing following command
in U-Boot. The image will boot afterwards.
> tftpboot 0x81000000 x4q.bin; bootm
5. SCP the sysupgrade-image into '/tmp'.
Remember to assign yourself an IP in 192.168.1.0/24 for this step!
Sven Eckelmann [Fri, 8 Feb 2019 20:20:20 +0000 (21:20 +0100)]
mac80211: ath10k: support for management rate control
Issues a wmi command to firmware when multicast rate change is received with the
new BSS_CHANGED_MCAST_RATE flag. Also fixes the incorrect fixed_rate setting
for CCK rates which got introduced with addition of ath10k_rates_rev2 enum.
By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Sven Eckelmann [Fri, 8 Feb 2019 20:20:20 +0000 (21:20 +0100)]
ath10k-ct: support for management rate control
By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.
This change makes use of WMI_VDEV_PARAM_MGMT_RATE param for configuring the
management packets rate to the firmware.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2019-02-08:
Fix rate-ctrl assert related to bad logic that tried to guess
that lower bandwidth probes were automatically successful if
higher was. The NSS mismatch that can happen here caused the
assert. Just comment out the offending code
(per comment from original QCA code). This is bug 69.
2019-02-10:
Fix bssid mis-alignment that broke 4-addr vlan mode (bug 67).
Original buggy commit was
commit 2bf89e70ecd1 ("dev-ds: Better packing of wal_vdev struct.")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
build: add KERNEL_ENTRY and sort DEFAULT_DEVICE_VARS
The KERNEL_ENTRY was missing from the DEFAULT_DEVICE_VARS.
This bug was discovered while preparing alternative images
for the mpc85xx's TP-Link WDR4900-V1, which all failed to
boot due to this:
|## Booting kernel from Legacy Image at 02000000 ...
| Image Name: POWERPC OpenWrt Linux-4.14.96
| Image Type: PowerPC Linux Kernel Image (uncompressed)
| Data Size: 2056568 Bytes = 2 MiB
| Load Address: 01000000
| Entry Point: 00000000
| Verifying Checksum ... OK
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hans Dedecker [Sat, 9 Feb 2019 19:59:55 +0000 (20:59 +0100)]
vti: remove setting default firewall zone to wan
Same reasoning as in bdedb798150a58ad7ce3c4741f2f31df97e84c3f; don't set
default firewall zone to wan as the firewall zone for the vti interface
can be configured in the firewall config or it makes it impossible not to
specify a firewall zone for the vti interface.
Hans Dedecker [Sat, 9 Feb 2019 19:48:11 +0000 (20:48 +0100)]
ipip: remove setting default firewall zone to wan
Same reasoning as in bdedb798150a58ad7ce3c4741f2f31df97e84c3f; don't set
default firewall zone to wan as the firewall zone for the ipip interface
can be configured in the firewall config or it makes it impossible not to
specify a firewall zone for the ipip interface.
HsiuWen Yen [Thu, 31 Jan 2019 16:45:22 +0000 (00:45 +0800)]
netfilter: fix checking method of conntrack helper
This patch uses nfct_help() to detect whether an established connection
needs conntrack helper instead of using test_bit(IPS_HELPER_BIT,
&ct->status).
The reason for this modification is that IPS_HELPER_BIT is only set when
the conntrack helper is attached by explicit CT target.
However, in the case that a device enables conntrack helper via the other
ways (e.g., command "echo 1 > /proc/sys/net/netfilter/nf_conntrack_helper")
, the status of IPS_HELPER_BIT will not present any change. That means the
IPS_HELPER_BIT might lose the checking ability in the context.
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti XM and XW family, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.
Also add the required package for this.
While at that, remove coefficients needed for PWM LEDs, as XM and XW
boards do not support PWM LEDs.
Julien Rabier [Mon, 4 Feb 2019 20:03:35 +0000 (21:03 +0100)]
ar71xx: fix RB941-2nD detection
Some hAP lite routers aren't detected because
/proc/cpuinfo shows "RouterBOARD RB941-2nD"
instead of "RouterBOARD 941-2nD".
Fix that.
Signed-off-by: Julien Rabier <taziden@flexiden.org>
[Alter string to include all flavours + slight rewrite of commit msg] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Edoardo Scaglia [Fri, 1 Feb 2019 15:43:46 +0000 (16:43 +0100)]
ar71xx: fix Arduino Yun enabling of level shifters outputs
As show in Arduino Yun schematic [1] GPIO 21 and 22 are connected to
output enable pin (OE) of two NTB01xx level shifters.
NTB01xx datasheets [2] [3] states that OE pin are active-high
therefore we should initialize GPIO 21 (DS_GPIO_OE) and GPIO 22
(DS_GPIO_OE2) accordingly to actually enable level shifters outputs.
Petr Štetiar [Thu, 3 Jan 2019 19:20:19 +0000 (20:20 +0100)]
kernel: add missing symbols to 4.19
While preparing 4.19 for imx6 and test building it with
CONFIG_ALL_KMODS=y with verbose mode enabled, I was asked by kernel
config about few missing symbols/modules
Let's add them to the generic config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[slight rewrite of commit log] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Daniel Golle [Fri, 8 Feb 2019 03:50:47 +0000 (04:50 +0100)]
mac80211: rt2x00: remove patch causing low tx power
Remove 980-rt2x00-reduce-power-consumption-on-mt7620.patch which in
combination with the most recently added patch reportedly causes TX
power to be too weak.
"without patches rssi on receiver is ~ -23dBm with 980 about -35dBm,
with both patches drops below -40dBm. with 987 only ~-28dBm"
We may need to reconsider this once we have implemented TSSI.
Fixes: cdb58b2bfe ("mac80211: rt2x00: reduce tx power to nominal level on RT6352") Reported-by: Tomislav Požega <pozega.tomislav@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 7 Feb 2019 23:03:40 +0000 (00:03 +0100)]
mac80211: rt2x00: reduce tx power to nominal level on RT6352
Current implementation of RT6352 support provides too high tx power
at least on iPA/eLNA devices. Reduce amplification of variable gain
amplifier by 6dB to match board target power of 17dBm.
Transmited signal strength with this patch is similar to that of
stock firmware or pandorabox firmware. Throughput measured with iperf
improves. Device tested: Xiaomi Miwifi Mini.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Florian Eckert [Thu, 11 Oct 2018 11:10:56 +0000 (13:10 +0200)]
gre: remove setting default firewall zone to wan
There are two problems with this behaviour that the zone is set to wan
if no zone config option is defined in the interface section.
* The zone for the interface is "normally" specified in the firewall
config file. So if we have defined "no" zone for this interface zone
option is set now to "wan" additonaly if we add the interface in the firewall
config section to the "lan" zone, the interface is added to lan and wan at once.
iptables-save | grep <iface>
This is not what I expect.
* If I do not want to set a zone to this interface it is not possible.
Remove the default assigment to wan if no zone option is defined.
If some one need the option it stil possible to define this option.
Signed-off-by: Florian Eckert <fe@dev.tdt.de> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Petr Štetiar [Thu, 3 Jan 2019 02:25:11 +0000 (03:25 +0100)]
ath79: ag71xx: Fix tx queue timeouts during ifup
On ath79 and UBNT Bullet M XW (ar9342) I was experiencing weird issues during
network setup[1] which I was able to reproduce easily with following commands:
uci set network.lan.ipaddr='192.168.1.20'
uci commit network
ifup lan
Which resulted after some time in:
...
WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:461 dev_watchdog+0x16c/0x280
NETDEV WATCHDOG: eth0 (ag71xx): transmit queue 0 timed out
...
Sometimes I wasn't able to use networking anymore, sometimes it was enough to
just ifdown/ifup lan and network was backup. On ar71xx it was all working just
fine.
I've found out, that it was happening because ag71xx_poll() wasn't called, thus
the TX queue wasn't emptied. The ag71xx_poll() is being called from napi
hrtimer, which is enabled by napi_schedule() in ar71xx_interrupt(), but since
no interrupts were ever fired again after ag71xx_stop() was called, it was
always leading to tx queue timeouts:
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[move ag->link before ag71xx_hw_disable to retain ordering as original] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Petr Štetiar [Fri, 18 Jan 2019 08:25:59 +0000 (09:25 +0100)]
build: Fix missing device variables for artifacts
It was reported to me today on IRC, that building of artifacts doesn't
work properly if the concat_cmd references DEVICE_NAME variable. I've
found out, that it's due to missing call of Device/Export in artifacts
building code path, so this patch adds the missing Device/Export call
which in turn exports DEFAULT_DEVICE_VARS into the artifacts
environment.
Fixes: 493c9a35516c ("build: Introduce building of artifacts") Tested-by: Oskari Lemmela <oskari@lemmela.net> Reported-by: Oskari Lemmela <oskari@lemmela.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
Ju Se Hoon [Tue, 8 Jan 2019 08:54:19 +0000 (17:54 +0900)]
ramips: add kmod-mt76x2 to WeVo 11AC NAS
The WeVo 11AC NAS has a MT7612E 802.11ac chip on the PCB.
Signed-off-by: Ju Se Hoon <joosahoon@gmail.com>
[renamed author from Albis-dev to real name, editted commit message] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
<https://www.openwall.com/lists/musl/2019/01/21/8>
"This release makes improvements with respect to default thread stack
size, including increasing the default from 80k to 128k, increasing
the default guard size from 4k to 8k, and allowing the default to be
increased via ELF headers so that programs that need larger stacks can
be build without source-level changes, using just LDFLAGS.
Insufficient stack size for AIO threads on kernels that don't honor
the constant MINSIGSTKSZ is also fixed.
The glob core has been rewritten to fix inability to see past
searchable-but-unreadable path components, and to avoid excessive
stack usage and unnecessary syscalls. The tsearch AVL tree
implementation has also been rewritten for better size and
performance. The math library adds more native single-instruction
implementations for arm, s390x, powerpc, and x86_64.
Various bugs are fixed, including several possible deadlocks, one of
which was a new regression in 1.1.20."
detailed release notes can be found in the WHATSNEW file:
<http://git.musl-libc.org/cgit/musl/tree/WHATSNEW#n1989>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Petr Štetiar [Sun, 30 Dec 2018 11:42:53 +0000 (12:42 +0100)]
ramips: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.
Petr Štetiar [Sun, 30 Dec 2018 11:17:25 +0000 (12:17 +0100)]
ramips: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.
This patch splits the big board case switch in 02_network in
two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs()
just like ath79 and ramips do.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Petr Štetiar [Sun, 30 Dec 2018 11:42:53 +0000 (12:42 +0100)]
brcm63xx: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.
Petr Štetiar [Sun, 30 Dec 2018 11:17:25 +0000 (12:17 +0100)]
brcm63xx: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.
* Jan 2, 2019
Rebase patches to make 9980 bisectable.
* Jan 2, 2019
Fix scheduling related assert when wal-peer is deleted with pending
tx buffers (bug 54, and others)
* Jan 7, 2019:
Fix specifying retransmits for AMPDU frames. It was previously ignored
since it is a 'software' retransmit instead of a hardware retransmit.
* Jan 9, 2019
Fix potential way to get zero rates selected (and then assert)
* Jan 18, 2019
pfsched has specific work-around to just return if we find invalid flags AND
if we are in an out-of-order situation. Maybe this is last of the pfsched
related issues (bug 54 and similar).
* Jan 24, 2019
The rcSibUpdate method can be called concurrently with IRQ tx-completion callback,
and that could potentially allow the tx-completion callback to see invalid state
and assert or otherwise mess up the rate-ctrl logic. So, disable IRQs in
rcSibUpdate to prevent this. Related to bug 58.
* Jan 28, 2019
Ensure that cached config is applied to ratectrl objects when fetched from
the cache. This should fix part of bug 58.
* Jan 28, 2019
Ensure that ratectrl objects from cachemgr are always initialized. This fixes
another part of bug 58.
* Jan 30, 2019
Better use of temporary rate-ctrl object. Make sure it is initialized, simplify
code path. This finishes up porting forward similar changes I made for wave-1
firmware long ago, and fixes another potential way to hit bug-58 issues.
* Jan 30, 2019
Cachemgr did not have a callback for when memory was logically freed. This means
that peers could keep stale references to rate-ctrl objects that were in process
of being DMA'd into to load a different peer's rate-ctrl state. This was causing
the bugcheck logic to fail early and often, and I suspect it might be a root cause
of bug 58 as well. The fix is to add a callback and set any 'deleted' memory references
to NULL so that we cannot access it accidentally. Thanks to excellent logs and patience
from the bug-58 reporter!
Hans Dedecker [Mon, 4 Feb 2019 07:48:01 +0000 (08:48 +0100)]
toolchain/gcc: backport FORTIFY patch to 5.5.0
Commit e61061a0886e2d0d6b075d75ae9b53d0a6bc9042 added support for hardening
options in the toolchain. However this breaks the gcc5.5.0 compilation in
case FORTIFY_SOURCE is set different from FORTIFY_SOURCE_NONE as reported
in [1].
Fix this by backporting the upstream patch which fixes this in later gcc versions
Felix Fietkau [Sun, 3 Feb 2019 19:45:26 +0000 (20:45 +0100)]
mt76: update to the latest version
a9d4c0e mt76: mt76x2: avoid running DPD calibration if tx is blocked 4d7e13f mt76: explicitly disable energy detect cca during scan e3c1aad mt76: run MAC work every 100ms 4e8766a mt76: clear CCA timer stats in mt76x02_edcca_init e301f23 mt76: measure the time between mt76x02_edcca_check runs 74075ef mt76: increase ED/CCA tx block threshold
drm: Add support for a panel-orientation connector property, v6
On some devices the LCD panel is mounted in the casing in such a way that
the up/top side of the panel does not match with the top side of the
device (e.g. it is mounted upside-down).
This commit adds the necessary infra for lcd-panel drm_connector-s to
have a "panel orientation" property to communicate how the panel is
orientated vs the casing.
Userspace can use this property to check for non-normal orientation and
then adjust the displayed image accordingly by rotating it to compensate.
Felix Fietkau [Thu, 31 Jan 2019 22:17:49 +0000 (23:17 +0100)]
mt76: update to the latest version
a4ec45c mt7603: fix LED support (copy CFLAGS from main Makefile) edda5c5 mt76x02: use mask for vifs dd52191 mt76x02: use commmon add interface for mt76x2u a80acaf mt76x02: initialize mutli bss mode when set up address 38e832d mt76x02: minor beaconing init changes 171adaf mt76x02: init beacon config for mt76x2u dcab682 mt76: beaconing fixes for USB ff81de1 mt76x02: enable support for IBSS and MESH 8027b5d mt7603: remove copyright headers e747e80 mt76: fix software encryption issues 2afa0d7 mt7603: remove WCID override for software encrypted frames
Felix Fietkau [Wed, 30 Jan 2019 14:17:01 +0000 (15:17 +0100)]
mt76: update to the latest version
c3da1aa mt7603: trigger beacon stuck detection faster 7a53138 mt7603: trigger watchdog reset if flushing CAB queue fails 6eef33b mt7603: remove mt7603_txq_init ae30c30 mt76: add driver callback for when a sta is associated 0db925f mt7603: update HT/VHT capabilities after assoc b5ac8e4 mt7603: initialize LED callbacks only if CONFIG_MT76_LEDS is set c989bac mt76x0: eeprom: fix chan_vs_power map in mt76x0_get_power_info 24bd2c0 mt76x0: phy: report target_power in debugfs bc7ce2a mt76x0: init: introduce mt76x0_init_txpower routine
When config_get is called as "config_get section option" the option
is unexpectedly globbed by the shell which differs from the way options
are read to a variable with "config_get variable section option".
Add another layer of double quotes to fix it.
Michal Hrusecky [Thu, 11 Oct 2018 16:23:19 +0000 (18:23 +0200)]
build: Use LINUX_DIR for Kernel/Patch
Use LINUX_DIR as a path when patching kernel. Doesn't break the current usage,
but allows to create packages that will contain variation of a kernel with
kernel being build in some subdirectory of PKG_BUILD_DIR.
Signed-off-by: Michal Hrusecky <michal.hrusecky@nic.cz>
Jo-Philipp Wich [Sat, 20 Oct 2018 10:18:03 +0000 (12:18 +0200)]
ar71xx: fix packed-not-aligned error with GCC 8.
Building ar71xx currently fails with:
In file included from ./include/linux/ipv6.h:5,
from ./include/net/ipv6.h:16,
from ./include/net/inetpeer.h:16,
from ./include/net/ip_fib.h:24,
from ./include/net/switchdev.h:17,
from ./include/net/dsa.h:23,
from arch/mips/ath79/dev-dsa.h:15,
from arch/mips/ath79/dev-dsa.c:17:
./include/uapi/linux/ipv6.h:107:1: error: alignment 1 of 'struct ipv6_destopt_hao' is less than 2 [-Werror=packed-not-aligned]
} __attribute__((packed));
Address this issue by correcting the alignment of the struct packing
pragma accordingly.
Jeffery To [Wed, 12 Dec 2018 17:33:36 +0000 (01:33 +0800)]
build: fix STAGING_DIR cleaning for packages
This fixes two issues with cleaning package files from STAGING_DIR:
* CleanStaging currently can only remove files and not directories. This
changes CleanStaging to use clean-package.sh, which does remove
directories.
* Because of the way directories are ordered in the staging files list,
clean-package.sh currently tries (and fails) to remove parent
directories before removing subdirectories. This changes
clean-package.sh to process the staging files list in reverse, so that
subdirectories are removed first.
Val Kulkov [Thu, 20 Dec 2018 20:04:43 +0000 (15:04 -0500)]
busybox: keep syslog.conf during sysupgrade
If a user finds that logd is too barebone for their needs and wishes
to have more control over syslog, the user presently has an option
to enable CONFIG_BUSYBOX_CONFIG_FEATURE_SYSLOG and configure syslog
with settings in /etc/syslog.conf.
Presently /etc/syslog.conf silently disappears on sysupgrade. This
patch prevents such unwanted behaviour if busybox syslog is enabled
via CONFIG_BUSYBOX_CONFIG_FEATURE_SYSLOG.
projects / thirdparty / openwrt.git / log
