mediatek: filogic: add support for WAVLINK WL-WN573HX3
The WL-WN573HX3 is an AX3000 outdoor Access Point by WAVLINK,
also sold in Europe as 7Links WLR-1300 (ZX-5612).
Specifications:
- MT7981B + MT7976 AX3000 2x2 DBDC (160 MHz)
- 16 MiB SPI NOR, 256 MiB RAM
- Gigabit ethernet port, 802.3af PoE
- IP67 outdoor case for wall or pole mounting with
four single band RP-SMA fiberglass antennas (8 dBi)
Installation:
- OEM Web UI is at 192.168.30.1 which will forward to
http://netlogin.link (using a captive portal)
- login with default password `admin`
- skip setup wizard by navigating directly to
http://netlogin.link/html/meshUpgrade.html
- upload WN573HX3-sysupgrade.bin
- reset to factory defaults to discard OEM UCI settings
MAC address assignment:
LAN 80:xx:xx:76:xx:25 hw 0x44e
WLAN 2.4G 80:xx:xx:76:xx:27 factory 0x04 (label MAC)
WLAN 5G 82:xx:xx:46:xx:27
pair key 8a:xx:xx:76:xx:27 also on label, not used by OpenWrt
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Flashing via OEM WebUI:
1. Download the firmware image *-squashfs-factory.bin
2. Upload firmware image via OEM WebUI firmware update, do not keep settings
To revert back to OEM firmware:
https://wiki.teltonika-networks.com/view/Bootloader_menu
To enable mobile data connection send command to modem:
echo -ne 'AT+QNETDEVCTL=3,1\r\n' > /dev/ttyUSB2
Create DHCP interface with usb0 device.
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
Flashing via OEM WebUI:
1. Download the firmware image *-squashfs-factory.bin
2. Upload firmware image via OEM WebUI firmware update, do not keep settings
To revert back to OEM firmware:
https://wiki.teltonika-networks.com/view/Bootloader_menu
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
Update Mofi 5500 to at least stock firmware version 4.8.6. (Available on the Mofi website.)
Previous versions are untested in the upgrade process. Log into the LuCI web interface,
usually at 192.168.10.1 and visit the 'System->Backup/Flash Firmware' page.
Upload and flash the firmware as usual.
Note to Maintainers: Do not remove SUPPORTED_DEVICES from the Makefile!
The customized Mofi version of OpenWRT (stock firmware) expects to see mofi5500 as the device
name. The stock firmware does not allow for forcing an installation.
Without this line, users cannot upload the new firmware through the stock Mofi firmware.
This device uses cell modems that could use QMI or MBIM.
Add LuCI Modem Manager to allow people to use these. Also, if they have
two cell network cards, ethernet, USB, or other kinds of networks, they may wish
to use MWAN3 to allow failover amongst their networks.
Please compile it with mwan3 for multiple WAN connections.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com> Signed-off-by: Rick Mac Gillis <noreply@rickmacgillis.com>
Robert Marko [Thu, 17 Apr 2025 11:20:06 +0000 (13:20 +0200)]
uboot-tools: remove uneeded syncconfig
During envtools conversion to the generic uboot-tools package, a syncconfig
call was added to the configure step which was previously not there.
We received multiple spourious reports that now envtools were failing to
build [1], but it was not reproducible.
However, it seems that this could easily be reproduced on MacOS 15 and
somehow that syncconfig call is breaking build by Makefile.autoconf not
being executed and thus no "include/config.h" is generated.
So, since this call was not previously there and U-Boot will actually do
syncconfig on its own when needed lets drop it.
Jakub Łabuz [Fri, 11 Apr 2025 16:33:49 +0000 (18:33 +0200)]
comgt-ncm: fix modem manufacturer detection
Fix an issue where NCM interface initialization fails because of wrong
modem manufacturer detection.
gcom call returns an output with Windows-style line breaks (containing \r)
what makes awk call return empty or malformed manufacturer name. Changing
awk RS variable to handle both \n and \r\n as line break fixes this issue.
INAGAKI Hiroshi [Thu, 9 Jan 2025 13:36:36 +0000 (22:36 +0900)]
uboot-ath79: update to v2025.04
Update uboot-ath79 package to v2025.04 for ath79 devices.
Additionally, new "CONFIG_NO_NET" option was introduced and replaced
disabled CONFIG_NET option ("# CONFIG_NET is not set"). So replace
that old options in the NEC Aterm devices as well.
Robert Marko [Wed, 16 Apr 2025 12:04:26 +0000 (14:04 +0200)]
tools: gmp: fix compilation with GCC15
Fedora 42 updated to GCC15 which now defaults to GNU23 as the default
instead of GNU17[1], and this breaks GMP compilation by failing to find
a working compiler test.
Its been fixed upstream [2][3], so backport the fix to fix GCC15 compilation.
Georgi Valkov [Mon, 14 Apr 2025 13:07:25 +0000 (16:07 +0300)]
toolchain: gcc: fix build error with Xcode 16.3
Xcode 16.3 defines TARGET_OS_MAC, it was not defined in prior versions.
zutil.h conditionally defines fdopen as NULL when this macro is defined,
resulting in the following build error:
In Xcode 16.2 and earlier, TARGET_OS_MAC was not defined so this entire
block was ignored, gcc and gdb used to compile and work fine.
This may have been used for compatibility with older versions of macOS,
but is no longer needed. By pure luck, the build worked fine for a long
time, because it did not properly detect macOS.
Fixed by removing the check for TARGET_OS_MAC.
Note that since Xcode 16.3, an entire set of TARGET_OS macros
are now defined, most of which are set to 0:
TARGET_OS_LINUX 0
TARGET_OS_MAC 1
TARGET_OS_OSX 1
Georgi Valkov [Mon, 14 Apr 2025 12:28:23 +0000 (15:28 +0300)]
toolchain: gdb: fix build error with Xcode 16.3
Xcode 16.3 defines TARGET_OS_MAC, it was not defined in prior versions.
zutil.h conditionally defines fdopen as NULL when this macro is defined,
resulting in the following build error:
In Xcode 16.2 and earlier, TARGET_OS_MAC was not defined so this entire
block was ignored, gcc and gdb used to compile and work fine.
This may have been used for compatibility with older versions of macOS,
but is no longer needed. By pure luck, the build worked fine for a long
time, because it did not properly detect macOS.
Fixed by removing the check for TARGET_OS_MAC.
Note that since Xcode 16.3, an entire set of TARGET_OS macros
are now defined, most of which are set to 0:
TARGET_OS_LINUX 0
TARGET_OS_MAC 1
TARGET_OS_OSX 1
Upstream version of ARM gc sections skip eeping some section. It was
reported some kernel load hang hence restore what we original did and
introduce a new patch that add the additional entry on top of the
upstream version.
Fixes: #18500 Fixes: 7843f21c5120 ("generic: replace ARM gc sections patch with upstream version") Tested-by: Stefan Kalscheuer <stefan@stklcode.de> (Turris Omnia) Link: https://github.com/openwrt/openwrt/pull/18503 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some regression were reported with the backported upstream version. Old
kernel require an additional flush in some case and this was handled in
the old downstream patch.
Reintroduce the flush to fix the regression and refresh affected patch.
The ATS SFP GT-T quirk patch was backported to stable kernel 6.6 but
was not notice while bumping the kernel version as they listed the quirk
at the bottom of the SFP quirk table while our hack patch put it at the
top.
With migrating to the upstream version, the duplication was made more
apparent.
Drop the double entry for the SFP module as it's already there and not
needed and refresh patches.
Chukun Pan [Tue, 4 Mar 2025 15:18:38 +0000 (23:18 +0800)]
kernel: add missing submenu for diag modules
The submenu of two diag modules is missing, fix it.
Fixes: 65de1e0 ("kernel: add missing symbols for lxc") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Link: https://github.com/openwrt/openwrt/pull/18480 Signed-off-by: Robert Marko <robimarko@gmail.com>
generic: replace ARM gc sections patch with upstream version
Replace ARM gc sections patch with upstream version. It seems this
feature is finally supported upstream with some minor difference.
In theory the upstream version should cut even more stuff, this really
needs to be evaluated if it's OK also to handle regression with the
kernel 6.12 update.
Rudy Andram [Thu, 27 Mar 2025 10:55:59 +0000 (10:55 +0000)]
dnsmasq: bump release to 2.91
updated 200-ubus_dns.patch
all remaining patches not required
Changelog for version 2.91 - https://thekelleys.org.uk/dnsmasq/CHANGELOG
version 2.91
Fix spurious "resource limit exceeded messages". Thanks to
Dominik Derigs for the bug report.
Fix out-of-bounds heap read in order_qsort().
We only need to order two server records on the ->serial field.
Literal address records are smaller and don't have
this field and don't need to be ordered on it.
To actually provoke this bug seems to need the same server-literal
to be repeated twice, e.g., --address=/a/1.1.1.1 --address-/a/1.1.1.1
which is clearly rare in the wild, but if it did exist it could
provoke a SIGSEGV. Thanks to Daniel Rhea for fuzzing this one.
Fix buffer overflow when configured lease-change script name
is too long.
Thanks to Daniel Rhea for finding this one.
Improve behaviour in the face of non-responsive upstream TCP DNS
servers. Without shorter timeouts, clients are blocked for too long
and fail with their own timeouts.
Set --fast-dns-retries by default when doing DNSSEC. A single
downstream query can trigger many upstream queries. On an
unreliable network, there may not be enough downstream retries
to ensure that all these queries complete.
Improve behaviour in the face of truncated answers to queries
for DNSSEC records. Getting these answers by TCP doesn't now
involve a faked truncated answer to the downstream client to
force it to move to TCP. This improves performance and robustness
in the face of broken clients which can't fall back to TCP.
No longer remove data from truncated upstream answers. If an
upstream replies with a truncated answer, but the answer has some
RRs included, return those RRs, rather than returning and
empty answer.
Fix handling of EDNS0 UDP packet sizes.
When talking upstream we always add a pseudo header, and set the
UDP packet size to --edns-packet-max. Answering queries from
downstream, we get the answer (either from upstream or local
data) If local data won't fit the advertised size (or 512 if
there's not an EDNS0 header) return truncated. If upstream
returns truncated, do likewise. If upstream is OK, but the
answer is too big for downstream, truncate the answer.
Modify the behaviour of --synth-domain for IPv6.
When deriving a domain name from an IPv6 address, an address
such as 1234:: would become 1234--.example.com, which is
not legal in IDNA2008. Stop using the :: compression method,
so 1234:: becomes
1234-0000-0000-0000-0000-0000-0000-0000.example.com
Fix broken dhcp-relay on *BSD. Thanks to Harold for finding
this problem.
Add --dhcp-option-pxe config. This acts almost exactly like
--dhcp-option except that the defined option is only sent when
replying to PXE clients. More importantly, these options are sent
in reply PXE clients when dnsmasq in acting in PXE proxy mode. In
PXE proxy mode, the set of options sent is defined by the PXE standard
and the normal set of options is not sent. This config allows arbitrary
options in PXE-proxy replies. A typical use-case is to send option
175 to iPXE. Thanks to Jason Berry for finding the requirement for
this.
Support PXE proxy-DHCP and DHCP-relay at the same time.
When using PXE proxy-DHCP, dnsmasq supplies PXE information to
the client, which also talks to another "normal" DHCP server
for address allocation and similar. The normal DHCP server may
be on the local network, but it may also be remote, and accessed via
a DHCP relay. This change allows dnsmasq to act as both a
PXE proxy-DHCP server AND a DHCP relay for the same network.
Fix erroneous "DNSSEC validated" state with non-DNSSEC
upstream servers. Thanks to Dominik Derigs for the bug report.
Handle queries with EDNS client subnet fields better. If dnsmasq
is configured to add an EDNS client subnet to a query, it is careful
to suppress use of the cache, since a cached answer may not be valid
for a query with a different client subnet. Extend this behaviour
to queries which arrive a dnsmasq already carrying an EDNS client
subnet.
Handle DS queries to auth zones. When dnsmasq is configured to
act as an authoritative server and has an authoritative zone
configured, and receives a query for that zone _as_forwarder_
it answers the query directly rather than forwarding it. This
doesn't affect the answer, but it saves dnsmasq forwarding the
query to the recursor upstream, which then bounces it back to dnsmasq
in auth mode. The exception should be when the query is for the root
of zone, for a DS RR. The answer to that has to come from the parent,
via the recursor, and will typically be a proof-of-non-existence
since dnsmasq doesn't support signed zones. This patch suppresses
local answers and forces forwarding to the upstream recursor for such
queries. It stops breakage when a DNSSEC validating client makes
queries to dnsmasq acting as forwarder for a zone for which it is
authoritative.
Implement "DNS-0x20 encoding", for extra protection against
reply-spoof attacks. Since DNS queries are case-insensitive,
it's possible to randomly flip the case of letters in a query
and still get the correct answer back.
This adds an extra dimension for a cache-poisoning attacker
to guess when sending replies in-the-blind since it's expected
that the legitimate answer will have the same pattern of upper
and lower case as the query, so any replies which don't can be
ignored as malicious. The amount of extra entropy clearly depends
on the number of a-z and A-Z characters in the query, and this
implementation puts a hard limit of 32 bits to make resource
allocation easy. This about doubles entropy over the standard
random ID and random port combination. This technique can interact
badly with rare broken DNS servers which don't preserve the case
of the query in their reply. The first time a reply is returned
which matches the query in all respects except case, a warning
will be logged. In this release, 0x020-encoding is default-off
and must be explicitly enabled with --do-0x20-encoding. In future
releases it may default on. You can avoid a future release
changing the behaviour of an installation with --no-x20-encode.
Fix a long-standing problem when two queries which are identical
in every repect _except_ case, get combined by dnsmasq. If
dnsmasq gets eg, two queries for example.com and Example.com
in quick succession it will get the answer for example.com from
upstream and send that answer to both requestors. This means that
the query for Example.com will get an answer for example.com, and
in the modern DNS, that answer may not be accepted.
* Update Mozilla certificate authority bundle to version 2.70.
The following certificate authorities were added (+):
+ Telekom Security TLS ECC Root 2020
+ Telekom Security TLS RSA Root 2023
+ FIRMAPROFESIONAL CA ROOT-A WEB
+ TWCA CYBER Root CA
+ SecureSign Root CA12
+ SecureSign Root CA14
+ SecureSign Root CA15
The following certificate authorities were removed (-):
- Security Communication Root CA (closes: #1063093)
ath79: fix initramfs execution for NEC Aterm devices
Fix execution of initramfs image on NEC Aterm devices by increasing
available memory for lzma extraction of lzma-loader.
The size of initramfs image of v24.10.0 exceeds available memory
(LZMA_TEXT_START - LOADADDR) and loader data running at LZMA_TEXT_START
will be overwritten by extracted data. As a result, LZMA extraction will
be broken and stuck (or unexpectedly reset).
Fix that issue by setting higher LZMA_TEXT_START address to increase
available memory for LZMA extraction by lzma-loader.
Zoltan HERPAI [Mon, 24 Feb 2025 12:18:01 +0000 (12:18 +0000)]
include: move generic riscv64 ISA to rv64gc
The current CFLAGS (rv64imafdc) for the riscv64 targets do not contain
the full generic compute extension (g), as that also includes the
zicsr and zifencei extensions/instructions. Rename the default ISA to
'generic' to add distinction to the current binaries (although it's very
minimal), and use rv64gc for CFLAGS.
This is also a prep step for the upcoming gcv (vector-extension supporting)
targets like the Spacemit K1, and the thead-cores like the TH1520.
Robert Marko [Fri, 11 Apr 2025 22:07:16 +0000 (00:07 +0200)]
layerscape: armv7: drop skipped packages
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv7.
Robert Marko [Fri, 11 Apr 2025 22:06:02 +0000 (00:06 +0200)]
ls-rcw: select by default for layerscape/armv7
Currently, ls-rcw package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in: 377b66990b97 ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-rcw' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-rcw package in DEVICE_PACKAGES lets select it when
layerscape/armv7 target is selected.
Robert Marko [Fri, 11 Apr 2025 19:06:18 +0000 (21:06 +0200)]
layerscape: armv8_64b: drop skipped packages
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv8_64b.
Robert Marko [Fri, 11 Apr 2025 21:33:57 +0000 (23:33 +0200)]
ls-ddr-phy: select by default for layerscape/armv8_64b
Currently, ls-ddr-phy package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in: 377b66990b97 ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-ddr-phy' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-ddr-phy package in DEVICE_PACKAGES lets select it when
layerscape/armv8_64b target is selected.
Robert Marko [Fri, 11 Apr 2025 21:33:24 +0000 (23:33 +0200)]
ls-dpl: select by default for layerscape/armv8_64b
Currently, ls-dpl package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in: 377b66990b97 ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-dpl' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-dpl package in DEVICE_PACKAGES lets select it when
layerscape/armv8_64b target is selected.
Robert Marko [Fri, 11 Apr 2025 21:32:41 +0000 (23:32 +0200)]
ls-mc: select by default for layerscape/armv8_64b
Currently, ls-mc package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in: 377b66990b97 ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-mc' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-mc package in DEVICE_PACKAGES lets select it when
layerscape/armv8_64b target is selected.
Robert Marko [Fri, 11 Apr 2025 21:18:30 +0000 (23:18 +0200)]
fman-ucode: select by default for layerscape/armv8_64b
Currently, fman-ucode package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in: 377b66990b97 ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~fman-ucode' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the fman-ucode package in DEVICE_PACKAGES lets select it when
layerscape/armv8_64b target is selected.
Robert Marko [Fri, 11 Apr 2025 20:57:27 +0000 (22:57 +0200)]
tfa-layerscape: set BUILD_DEVICES
Currently, tfa-layerscape packages are being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in: 377b66990b97 ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~trusted-firmware-a-ls1012a-frdm' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the individual TFA packages in DEVICE_PACKAGES we can just
do what other targets do and set BUILD_DEVICES so that TFA packages are
automatically set.
Robert Marko [Fri, 11 Apr 2025 22:32:23 +0000 (00:32 +0200)]
bcm63xx-cfe: install into image staging dir
Currently, bcm63xx-cfe is being installed into kernel build dir, however
that does not work for Image Builder as only certain artifacts from kernel
build dir are included in Image Builder.
So, simply install bcm63xx-cfe into image staging dir so its artifacts can
be used in Image Builder as well.
Schneider Azima [Mon, 10 Mar 2025 01:42:51 +0000 (18:42 -0700)]
mediatek: add support for Mercusys MR80X v3
This commit adds support for Mercusys MR80X(EU) v3 router.
Device specification:
- SoC: Mediatek MT7981b, Cortex-A53, 64-bit
- RAM: 512MB
- Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
- Ethernet: 4x 100/1000 Mbps LAN1,LAN2,LAN3 & WAN
- Wireless: 2.4GHz (802.11 b/g/n/ax)
- Wireless: 5GHz (802.11 a/n/ac/ax)
- LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs
on ethernet ports
- Buttons: 1 (Reset)
- Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Installation (UART):
- Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2
- Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'.
- Set the uboot environment for startup.
setenv tp_boot_idx 0; setenv bootcmd bootm 0x46000000; saveenv
If the bootarg is set to boot from ubi1, also change it to ubi0.
- Load and run OpenWrt initramfs image.
setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm
- Browse IP 192.168.1.1, upload the 'sysupgrade' image and do upgrade.
Recovery:
- Press Reset button and power on the router.
- Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware.
wifi-scripts: add hotplug handler for slow-to-initialize ath12k radios
Some ath12k radios can take long time to initialize and register a
phy. This can cause netifd to fail to detect them during initial scan.
To address this issue, a hotplug script has been added to retry
configuration once they have registered their phy.
Paul Donald [Wed, 26 Mar 2025 17:43:45 +0000 (18:43 +0100)]
lldpd: enable hardware inventory information (TLV) management
lldpd can send several hardware inventory TLV fields. Extend the init
script to provide these when the existing flag 'lldpmed_no_inventory' is
disabled. Five new methods provide default values for some of them,
taken from /etc/os-release and /etc/board.json.
There is no homogeneous method to determine the hardware serial number,
so it can be provided manually, as can asset ID.
Note: properties >= 32 characters are truncated at send time (by lldpd),
and some (Cisco) equipment displays junk after strings >= 32 characters.
So truncate to 31.
Tested on: 24.10.0 (known compatible with 22 and 23 also)
generic: fix kernel warning no previous prototype for ...
It seems new kernel version introduced -Wmissing-prototypes. This new
warning reported drivers that define non static function that are used
statically in the driver.
Fix this by declaring making those function actually static if not
defined in any header and not used outside of the single driver.
It seems new kernel linux version reorganized the header include and now
of.h needs to be explicitly included. This should have been done from
when the driver was introduced.
Add the missing of.h header to fix compilation error in later kernel
version.
Yang Xiwen [Thu, 10 Apr 2025 11:09:42 +0000 (19:09 +0800)]
qualcommax: eap623od-hd-v1: fix phy node and LED config
The reason phy fails to probe without explicitly overrided phy id is
that the reset timing fails to match. Fix it with proper `reset-delay-us` and
`reset-post-delay-us`.
While at it, change LED settings to match EAP610-Outdoor.
Serial Interface:
TP10 - 3.3V can be used for level shifter, if needed
TP9 - TX
TP8 - RX
TP11 - GND
Interface properties: 115200, 8N1
Access to console using serial port for OEM firmware:
Username: admin
Password: 1234
Flashing via TFTP (no disassembling or soldering required):
1. Connect your PC and router to port LAN
2. Configure PC interface using static IP 192.168.1.225, mask
255.255.255.0
3. Place OpenWRT firmware image (*-squashfs-tftp-recovery.bin) to TFTP
root folder and renamed it to tp_recovery.bin
4. Unplug power from router
5. Press and hold Reset/WPS button
6. Power up the router
7. Wait until TFTP started uploading image (~10 seconds after power up)
and release Reset/WPS button
8. Wait until image uploaded, i.e. until LAN LED start lighting
9. Enable DHCP address on PC interface and wait for assigning address
10. Use ssh (root@192.168.1.1) to configure router properties
Depends on patch for firmware-utils package:
https://github.com/openwrt/firmware-utils/commit/2051fe5b
Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
Download initramfs image, reboot router,
waiting for tftp recovery to complete.
After openwrt boots up, perform sysupgrade.
CONFIG_QCOM_IPA kernel cofig was enabled by mistake and conflicts with
mac80211 as it indirectly selects QMI HELPERS. Backports project provid
his own version of QMI HELPERS hence it should not be built-in.
Make the RPM partition read-only. This was a mistake and a leftover from
staging branch but I can take this mistake as an excuse to document the
current problem with RPM.
It might happen that a board ship with a broken RPM .mbn, broken not in
the sense that the board doesn't boot or it's a brick but broken in the
sense that it's outdaed and suffer from a bug fixed in new version.
This bug consist in a problem with the regulators between USB and NSS.
The old RPM mess with the NSS regulator (l2) and change the voltage for
it while configuring the USB regulator (l5).
This cause the ethernet subsystem to malfunction with the port not
working.
To workaround this, it's needed to disable RPM handling and CPUFreq.
With these 2 disabled, the old RPM doesn't touch regulators and Ethernet
works correctly.
New RPM correctly handle regulators for USB (l5) and doesn't suffer from
this problem. A solution for this is getting discussed with QCOM hoping
to get some good feedback for it.
Add pending patch fixing NSSCC boot stall. These patch are needed to
prevent the ICC to disable critical clock for NSSCC NOC.
Without these the system will stall and reboot with watchdog.
While at it also remove an extra clock from DTSI as it currently have no
use. Original patch is not modified to keep consistency with series
proposed upstream.
qualcommbe: ipq95xx: Refresh dts SPI-NAND patch to v14
Refresh dts SPI-NAND patch to to v14. This is to keep stuff synced with
current pending patch revision and make it easier to replace patch
later (and discover something broke in the meantime)
qualcommbe: ipq95xx: Refresh the NSSCC and PORT patch for new PCIe patches
Refresh the NSSCC patch for new PCIe patches. To keep track of fuzz
changes for the IPQ95xx patches, patch are not refreshed currently.
For the specific case of NSSCC patch, quilt gets confused and apply the
patch in the wrong node, putting it in the RPM node (causing all kind of
funny errors at runtime)
Correctly fix the patch to put the node right after the PCIe nodes.
Also the PORT patch need to be refreshed as the gpio header is added by
the PCIe patch.
generic: move QCOM SPI NAND driver to generic backports
QCOM SPI NAND driver got merged upstream hence we can drop the special
patch from qualcommax and qualcommbe target and move them to the generic
backports directory to reduce patch maintenance.
While at it refresh any affected patch and target and also backport other
minor fixup for the SPI NAND driver merged upstream later.
Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.85..HEAD
(HEAD -> bba53a117a4a5c29da892962332ff1605990e17a)
Linus Walleij [Sun, 11 Jun 2023 22:15:18 +0000 (00:15 +0200)]
gemini: Activate serial USB console on the DNS-313
This brings up a serial console on the USB device port of
the DNS-313 by:
- Activating the usbgadget feature
- Selecting the usbgadget-acm package
- Adding an inittab that opens a console at ttyGS0 which is
the device side of ttyACMn of a connected host
Sync jitterentropy source code with linux-6.12 to solve the
issue of jitterentropy initialization failed:
[ 9.523489] jitterentropy: Initialization failed with host not compliant with requirements: 9
[ 9.661916] kmodloader: 1 module could not be probed
[ 9.662377] kmodloader: - jitterentropy_rng - 0
In linux upstream commit cf27d9475f37 ("crypto: jitter - use
permanent health test storage"), when FIPS crypto is disabled,
the health test results are always explicitly skipped. That means
it will never return error code 9 (health test failed) again.
Fixes: https://github.com/openwrt/openwrt/issues/16684 Signed-off-by: Shiji Yang <yangshiji66@outlook.com> Link: https://github.com/openwrt/openwrt/pull/18399 Signed-off-by: Robert Marko <robimarko@gmail.com>
build: bpf: fix LLVM tool paths with host toolchain
Do not assume that the various tools like llc can be found under the
same path as clang; instead, look them up through BPF_PATH (while still
preferring ones found next to clang).
This fixes build in common setups with ccache, where clang resolves to a
path like /usr/lib/ccache/bin/clang, but no other tools can be found at
that location.
projects / thirdparty / openwrt.git / log
