realtek: 6.12: refactor EEE for RTL8218B/D and RTL8214FC
Three different code paths for the same phy model. Now the bus
is prepared to handle c45 (mmd) read/writes correctly. Remove
the custom implementations and let generic kernel functions do
their best. To achieve this
- disable the PHY-mode EEE in rtl821x_config_init() as upstream does
- provide mmd read/write functions that avoid EEE via c45 over c22
While chaning the phy_driver functions sort them alphabetically.
With the follow up EEE patches the mdio bus will run c22 and c45
accesses during initial scan. Especially when accessing addresses
beyond the CPU port phy requests might fail in a way that cannot
be handled gratefully. Do two things
- do not allow access to addresses starting from cpu port
- set the scan disable bitmask to ports starting from cpu port
realtek: 6.12: enhance mdio max port patch (once again)
Some bits where missed during the last enhancement of the mdio
patch. In the forthcoming patches the phy_mask will be populated
to avoid unwanted ports (>= cpu port) from being scanned. Add
additional locations where 32 bit values need to be converted
to 64 bits.
realtek: 6.12: align internal/external mac eee function names
The DSA driver uses set_mac_eee() for the outside API while
the interal helper is called port_eee_set(). Align that.
Additionally do not call the internal helpers directly by
the function names but use the register assignments.
Upstream will get rid of the get_mac_eee() function in the DSA
driver and replace it by a boolean alternative. While we fill a
lot of data here (because of EEE bugs in the Realtek phy layer)
other DSA drivers only return if EEE is available or not for a
port. To make the next kernel upgrade easier follow that design.
realtek: 6.12: relocate R4K deactivation to late CPU init
To avoid unneeded interrupts the R4K timer is deactivated during
secondary cpu initialization. This is currently done during
phase init_secondary(). With the upgrade to 6.12 the kernel runs
a primary/secondary cpu timer/counter synchronization to verify the
proper setup in synchronise_count_slave(). That runs at a later
point in time and expects the secondary counter to be fully
functional. Finding a deactivated counter results in the following
messages:
WARNING: CPU: 1 PID: 0 at arch/mips/kernel/sync-r4k.c:99 check_counter_warp+0x220/0x254
Warning: zero counter calibration delta: 0 [max: 6500000]
Counter synchronization [CPU#0 -> CPU#1]:
Measured 278760029 cycles counter warp between CPUs
Relocate the deactivation to smp_finsh() at the end of the cpu
startup sequence. Additionally polish the startup code and remove
all unneeded parts.
realtek: 6.12: fix phy-mode for XGS1250-12 port 1-8
Per IEEE 802.3 definition we have:
- parallel XGMII for single 10GBit ONLY links
- serial USGMII for 8 port 1GBit links (not known by kernel)
- serial USXGMII: for single/multiple links with a total bandwidth of 10GBit
The phy-mode of the first eight ports of the XGS1250-12 have always been
defined as XGMII (without S). This came from a confusion with the similar
named Realtek proprietary XSGMII (with S) mode that is basically 10GB SGMII.
From the above definition this is wrong but worked until kernel 6.6. With
the upgrade to 6.12 there is an enforced capabilities check within
phy_caps_from_interface() and link validation fails with
lan1: validation of xgmii with support 62ef and advertisement 62c0 failed: -EINVAL
lan1: failed to connect to PHY: -EINVAL
lan1: error -22 setting up PHY for tree 0, switch 0, port 0
Switch the ports to USXGMII as the most flexible option. This might be no
final solution but at least it better describes the phy/mac link.
realtek: 6.12: adapt RTL9300 i2c bus & mux drivers
Fix minor compilation errors due to kernel changes.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com> Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> Link: https://github.com/openwrt/openwrt/pull/18935 Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream has integrated the Realtek target into the generic MIPS
initialization and so MACH_REALTEK_RTL has gained some new features.
Especially:
- CONFIG_MACH_GENERIC_CORE generates central modules
- board-realtek module adds device specific extensions
The current downstream initialization works well and upgrading to
kernel 6.12 is not the right time to harmonize this. Modify the
MACH definitions to the current needs.
The validate function no longer exists in phylink_mac_ops. Remove
it for the internal ethernet interface. Instead provide some
meaningful mac capabilities.
realtek: 6.12: replace ethtool_eee with ethtool_keee
EEE functions are now called with ethtool_keee instead of
ethtool_eee. Replace all occurrences. This will fix function
signature checks but still produces compilation errors due
to structure changes.
Eric Fahlgren [Fri, 6 Jun 2025 23:43:27 +0000 (16:43 -0700)]
package: rework contents of package index.json
Rework the generation of the index.json version of the package
indexes to match the original intent (i.e., for use by the ASU
server and other downstream projects). The current file contains
package names that have ABI versioning, making them unusable by ASU,
so we now remove the ABI suffixes.
Also adds a 'version' field to the json, so downstream utilities
can detect the new semantics of the package name fields.
Multiple users have reported a regression [1] in OpenWRT 24.10 with the
ramips/mt7621 target, which has the MT7530 PHYs: the Ethernet link is
periodically going down for a brief period of time:
mt7530-mdio mdio-bus:1f lan1: Link is Down
br-lan: port 1(lan1) entered disabled state
mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
The symptoms stop after disabling EEE and it was reported by Mediatek in
2021 that EEE is unstable for the MT7530 PHYs [2]:
> EEE of the 10-year-old MT7530 internal gephy has many IOT problems, so
> it is recommended to disable its EEE.
EEE is enabled by default for these devices in OpenWRT 24.10 whereas in the
previous version (OpenWRT 23.05, Linux 5.15) it was not. It was determined
that in Linux 6.6, the PHY driver tries to disable EEE in
mtk_gephy_config_init() in drivers/net/phy/mediatek-ge.c, but this is later
overridden by a subsequent execution of the genphy_c45_write_eee_adv()
function, which enables every EEE mode supported.
The best way forward for now seems to be to mark EEE as broken directly in
the devicetree, which affects the genphy_c45_write_eee_adv() function.
There are some devices, like GnuBee GB-PC2, that define additional PHYs,
for example ethernet-phy@5 or ethernet-phy@7. As reported by Chester A.
Unal, these are not MT7530 PHYs and they are not affected.
This would need to be cherrypicked for the OpenWRT 24.10 branch.
bmips: bcm6358: add support for Huawei HG556a ver C
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR Macronix MX29GL128EHT2I-90G
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Ralink RT3062F
- 3x USB 2.0 port
- 4x Button
- 13x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg556a-c-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
It's time to give the patches documentation some love by:
- Using Markdown.
- Differentiating between generic and specific target patches.
- Adding deeper explanation about patch numbering.
Missing headers causes an error on kernel 6.12:
arch/mips/ralink/irq.c:86:5: error: no previous prototype for 'get_c0_perfcount_int' [-Werror=missing-prototypes]
86 | int get_c0_perfcount_int(void)
| ^~~~~~~~~~~~~~~~~~~~
arch/mips/ralink/irq.c:92:14: error: no previous prototype for 'get_c0_compare_int' [-Werror=missing-prototypes]
92 | unsigned int get_c0_compare_int(void)
| ^~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Replace macros with empty body with 'do {} while (0)'.
Remove unnecessary semicolons.
Fixes:
drivers/mmc/host/mtk-mmc/sd.c: In function 'msdc_irq':
drivers/mmc/host/mtk-mmc/sd.c:1969:87: error: suggest braces around empty body in an 'else' statement [-Werror=empty-body]
1969 | IRQ_MSG("XXX CMD<%d> MSDC_INT_RSPCRCERR", cmd->opcode);
| ^
drivers/mmc/host/mtk-mmc/sd.c:1975:84: error: suggest braces around empty body in an 'else' statement [-Werror=empty-body]
1975 | IRQ_MSG("XXX CMD<%d> MSDC_INT_CMDTMO", cmd->opcode);
| ^
cc1: all warnings being treated as errors
Mathew McBride [Tue, 18 Mar 2025 23:00:52 +0000 (10:00 +1100)]
kernel: netdevices: rtl8366: ensure CONFIG_NET_DSA_REALTEK_RTL8366RB_LEDS is enabled
Add new setting CONFIG_NET_DSA_REALTEK_RTL8366RB_LEDS which
was introduced in kernel 6.12 and allows enabling LEDs for
the Realtek RTL8366RB subdriver.
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Eric Fahlgren [Fri, 6 Jun 2025 15:19:15 +0000 (08:19 -0700)]
apk-tools: update to git HEAD (2025-06-06)
3efd75dc7e49 crypto: fix segfault when passing --hash 51306cf1424e test: export APK_CONFIG=/dev/null b91e9e17ceb6 build: mark scdoc dependency as native 123fa05b787a build: mark lua interpreter dependency as native 5fbb85426ea0 libfetch: fix fetch_err* for negative error codes 1458737d58c2 db, index: fix 'index' loading of old index cbd1e6b49add add: use solver error when arch is incompatible f66d84fcd42d doc: update apk-package(5) regarding arch validation f5df274d248c test: don't use temporary files for diffing output 42034f7961f0 apk: allow per-applet option to override group options b6ca99d44119 serializer: start_array(num=-1) indicates unknown amount 14881b9ffb2e query: a new api and applet to search and output information dd2255e10ee9 package: use apk_array_foreach ae17b61de83b info: use apk_array_foreach 6d4471f55ada solver: use apk_array_foreach 7951798121c1 db: use apk_array_foreach 5e3cac4ccb85 commit: use apk_array_foreach 86c725d97afd db: allocate protected paths with balloc 0fe23ce1a501 array: make apk_array_foreach* evaluate end only once a50f7ea2dd02 io_url_wget: correctly init wget_out on apk_io_url_init call 2cdfdd86e3d4 commit: Fix 'upgrade' typo on cache-pre-download 3fb50f645203 Add man page for protected_paths.d 652a1365aa30 fetch: account existing files to progress 0257acf6b120 doc: remove .d from apk-protected_paths(5) man page name aeb74de67818 db: include index file name for APK_REPOTYPE_NDX 6ec4fe6fa334 mkpkg: handle apk_blob_split failure c47b6e17fe6d extract: handle apk_blob_split failure b7c6b0b468d7 mkpkg: print error message when using forbidden fields b9483c46bdf9 fetch: fix APK_BLOB_STRLIT used with char argument d495be9e9f25 adbsign: fix recompressing when alg is NONE or level is 0 5348babed78e mkndx: fix memory leak when with large dependency list in v2 packages 11dd5923f6a1 mkndx: don't return ADB_ERROR from mkndx_parse_v2meta 8415dbf6df42 mkndx: reset pkginfo on error 684bef440cde mkndx: remove workaround for abuild license field a94fa1878df9 pkg: move same origin check after replaces check 3abcd400bdbf pkg: fix package repos after 16th missing 216ac57b7a1a arch: reserve wasi32 architecture name for WASI APKs 3761e38d1a00 add wasi32/wasi64 reservations to apk-package(5) 68c1fa58113e dot: only initialize qs->mode.empty_matches_all once 56019c5ed390 {blob,tar,adb}: avoid overflow when pulling numbers 5112b60c4440 index: only check file name for old index 345863787484 db: fix ${name} check in apk_db_get_pkg_by_name 5ce64d14ead8 manifest: replace memset 0 with apk_blob_pushed 7765f134215d info: include name and version when --all is used d2ca47f9f3b4 fix indentation 33c822e93267 build: install apk_repoparser.h header 0762b25eb2ad ctx: initialize progress_char in apk_ctx_init 0a3fa796a532 doc: fix typos 10a184f3f43d search: fix incorrect error when no match was found aa9502dc3720 ctx: fix closing of root_fd 2ac55a0f26bd io: fix id_cache when root_fd is 0 c39b22fe49c7 fetch: fix outdir_fd when openat returns 0 9d42be2316fc meson: Build Python module using standard Meson python build functions 48c6e526ee6f meson: Allow overriding the names of the Lua binary and pkgconfig file 249f0d937afb ci: Add build test on Fedora Linux 10dbdf7263eb pkg: replace files/dirs from packages that will be removed acae571db2b9 pkg: apk_pkg_replaces_{dir,file} access ipkgs consistently 8b0b567544b7 io: initialize 'r' in apk_dir_foreach_config_file 55ab583de9a3 io: fix undefined behaviour in apk_istream_get_delim deadab38aea9 db: flush progress notes after opening indexes 32b3a448c3e2 info: always show name/version for no-legacy-info dbba5797269b crypto: make crypto backend an implementation detail c0288de355e6 test: fix failing tests due to missing PATH_MAX definition 1863ccbf7abb make: remove -DCRYPTO_USE_* e2fb020c96ca apk: shared error message for invalid arguments 29040298f5de adb: fix handling of empty adb blocks 2aa08ec9da6a adb: fix exact comparison of objects containing arrays e475a2fab226 Update apk-v3.5.scd 76c629d79473 doc: combine --no-* and --* descriptions afc1ee46ca55 mkpkg: convert --rootnode to APK_OPT_BOOL 2c52e9415653 pkg: correctly check empty atoms in apk_package f384d7d11229 test: add tests for query 0c044cb8323d tests: fix permissions on replaces.sh 31bc2263a10f defines: make BIT() always return a 64-bit type dc86ad784eef solver: always resolve conflict names in install-if 8b6e9c9d6421 db, pkg: separate "virtual" repository for command line packages d7f77eb68aa5 adb: reduce alignment of ADB_TYPE_INT_64 to 32 bits 1ffd648aca45 array: generalize apk_deps_balloc to apk_array_balloc 2089f8a8225b adb, pkg, query: add support for 'recommends' 59c207b582cc array: generalize apk_deps_bclone to apk_array_bclone 617ba801f760 commit: fix size_diff on package removal 649859806c65 commit, upgrade: never suggest --force-broken-world 4f84ee8156e1 help: group option group help first 44a7498d6102 fetch: fix error reporting if package is not selected 7516cf61fe94 adb: return bool from adb_block_is_ext f47cb4bdac15 adb: validate signature header version specific size 1925de55beef adb, pkg: add support for custom tags f174f287b1b2 db, doc: update and document environment variables for scripts 603eeea614b5 upgrade: improve the mechanism to detect self-upgrade done 97c2d3318d8d upgrade: determine apk-tools package name from /proc/self/exe 088f88cdb6a5 build, test: fix limits.h including and testing selfupgrade 8acf4c0e95da pkg: export APK_PACKAGE for package scripts ab907a6b682e io: ignore dot files in apk_dir_foreach_file() f5e4cbc3900e info: make --legacy-info the default for the time being 7f1afedb7cae doc/apk-v3(5): document that multiple SIG blocks are allowed 2204c49b9d7e adb: validate block type before testing the allowed mask 9331888de6bd apk-tools-3.0.0_rc5
The ENC28J60 is a 10 Mbps half-duplex Ethernet controller interfaced via SPI.
It achieves real-world bandwidth up to 5Mbit/s on devices like the RPi Zero due
to SPI limits.
Commonly used with Raspberry Pi Zero boards for wired network connectivity.
building with CONFIG_ALL_KMODS unearthed all sorts of interesting
failures
ERROR: module 'crypto/chacha-x86_64.ko' is missing.
ERROR: module 'crypto/poly1305-x86_64.ko' is missing.
ERROR: module 'crypto/curve25519-x86_64.ko' is missing.
ERROR: module 'crypto/camellia-x86_64.ko' is missing.
These stem from the main UML Makefile.
|# UML only makes sense on linux
|ifeq ($(HOST_OS),Linux)
| ifeq ($(HOST_ARCH),x86_64)
|
|ARCH:=x86_64
|BOARD:=uml
The modules in question define x86_64 optimized version and
the OpenWrt's buildsystem expects that these modules will be present.
SPI is not available due to the UML Architecture not setting HAS_IOMEM.
In the future, UML could get (virtualized) IOMEM and/or SPI could drop
the HAS_IOMEM dependency. A patch for the latter has been sent:
<https://lore.kernel.org/linux-spi/20250530234941.950431-1-chunkeey@gmail.com/T/#u>
mt76: Unfortunately, the firmware packages are picked up, but the
associated drivers can't be build because iowrite32+ioread32 are
not defined.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ramips: mt7621: include uboot-envtools in some missed devices
Add uboot-envtools (removing -uboot-envtools) to devices which were
missed in the commit 79bd017 ("ramips: mt7621: add uboot-envtools to
all devices")
- Mi Router 3G
- Mi Router AC2100
While at here remove two redundant entries from devices which were added
just after the referenced commit 79bd017 and did not account for the
new DEFAULT_PACKAGES member:
- SNR-CPE-ME1
- SNR-CPE-ME2-SFP
Fixes: 79bd017 ("ramips: mt7621: add uboot-envtools to all devices") Fixes: https://github.com/openwrt/openwrt/issues/18960 Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com> Link: https://github.com/openwrt/openwrt/pull/19012 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Sat, 7 Jun 2025 12:47:27 +0000 (08:47 -0400)]
kernel: add backport to fix build with GCC 15.1
Add the following to fix builds with GCC 15.1:
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/arch/mips/vdso?h=next-20250606&id=0f4ae7c6ecb89bfda026d210dcf8216fb67d2333
% dmesg | grep gcc
[ 0.000000] Linux version 6.6.93 (facade@redline) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 15.1.0 r29972+15-7d617804cfe7) 15.1.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sat Jun 7 12:13:18 2025
Error for reference:
./include/linux/stddef.h:11:9: error: cannot use keyword 'false' as enumeration constant
11 | false = 0,
| ^~~~~
./include/linux/stddef.h:11:9: note: 'false' is a keyword with '-std=c23' onwards
./include/linux/types.h:35:33: error: 'bool' cannot be defined via 'typedef'
35 | typedef _Bool bool;
| ^~~~
./include/linux/types.h:35:33: note: 'bool' is a keyword with '-std=c23' onwards
./include/linux/types.h:35:1: error: useless type name in empty declaration [-Werror]
35 | typedef _Bool bool;
| ^~~~~~~
CC arch/mips/lib/delay.o
AR arch/mips/fw/lib/built-in.a
AR arch/mips/fw/lib/lib.a
CC arch/mips/ralink/of.o
CC fs/read_write.o
CC block/elevator.o
cc1: all warnings being treated as errors
make[9]: *** [scripts/Makefile.build:243: arch/mips/vdso/vgettimeofday.o] Error 1
make[8]: *** [scripts/Makefile.build:480: arch/mips/vdso] Error 2
Shiji Yang [Sat, 15 Mar 2025 02:00:10 +0000 (10:00 +0800)]
ramips: some minor FDT improvements for HiWiFi devices
This patch contains various minor FDT improvements for ramips
HiWiFi series devices:
* Add mt76 driver compatibles.
* Remove useless platform compatibles.
* Add default USB LED trigger for HC5861.
* Disable unused usbphy for HC5661, HC5661A and HC581B.
* Add switch port map properties based on 02_network scripts.
* Move aliases node to device dts because the LED nodes it
references only exist in the device specific dts.
* Rename gpio-leds nodes to follow the upstream dt-bindings
suggested pattern "(^led-[0-9a-f]$|led)".
* Convert deprecated LED label property to color and function.
"system" LED has been renamed to "status", it is acceptable
because these LEDs do not have text labels.
Shiji Yang [Sat, 15 Mar 2025 02:00:10 +0000 (10:00 +0800)]
ramips: convert HiWiFi devices MAC address to NVMEM format
For all HiWiFi series devices, the base MAC address is stored on
"bdinfo" partition, offset 0x18a, ASCII text format. The recently
introduced "mac-base" nvmem layout can handle the ASCII text now,
so it's time to move MAC address configurations to dts. There is
no valid MAC info in the "factory" partition, hence they will be
replaced with the correct ones.
ramips: mt76x8: add Teltonika RUT951/RUT901 support
Specification:
- MediaTek MT7628AN SoC
- 128 MB of RAM EtronTech EM68C16CWQG-25IH
- 16MB of Flash Winbond W25Q128 SPI
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- MediaTek MT7628AN 2.4 GHz 802.11n WiFi
- Quectel EC25-EUX 4G cat 4 modem (RUT951) or Quectel EC200A-EU 4G cat 4 modem (RUT901)
- 1x Digital input
- 1x Digital output
- 2x SIM slot (can be swapped via GPIO)
- eSIM (depends on hardware configuration, can be swapped via GPIO)
GPIO:
- 1 button (Reset)
- 7 LEDs (power, status green/red, RSSI 1,2,3,4,5)
- 5 Modem control (power button, reset, status, SIM select, eSIM select)
- 1 Digital input
- 1 Digital output
Flashing via OEM WebUI:
1. Download the firmware image *-squashfs-factory.bin
2. Upload firmware image via OEM WebUI firmware update, do not keep settings
To revert back to OEM firmware:
https://wiki.teltonika-networks.com/view/Bootloader_menu
Mobile data connection:
Quectel EC200A-EU send command to modem:
echo -ne 'AT+QNETDEVCTL=3,1\r\n' > /dev/ttyUSB2
Create DHCP interface with usb0 device.
Quectel EC25-EUX create proto qmi interface.
ramips: mt76x8: add Teltonika RUT956/RUT906 support
Specification:
- MediaTek MT7628AN SoC
- 128 MB of RAM EtronTech EM68C16CWQG-25IH
- 16MB of Flash Winbond W25Q128 SPI
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- MediaTek MT7628AN 2.4 GHz 802.11n WiFi
- Quectel EC25-EUX (RUT956) or Meig SLM770A (RUT906) modem
- GNSS
- RS232, DB9 connector, Cypress ACM via USB, /dev/ttyACM0
- RS485 /dev/ttyS1
- microSD card slot
- 2.0 USB Type-A HOST port
- analog 0-24V input (MCP3221)
- Relay
- 2x Digital input
- 2x Digital output
- 2x SIM slot (can be swapped via GPIO)
- eSIM (depends on hardware configuration, can be swapped via GPIO)
GPIO:
- 1 button (Reset)
- 7 LEDs (power, status green/red, RSSI 1,2,3,4,5)
- 5 Modem control (power button, reset, status (v5 hw), SIM select, eSIM select)
- 2 Digital input
- 2 Digital output
- 1 Isolated input
- 1 RS485 tx enable
- 1 RS485 rx enable
- 1 Relay
- 1 Data Carrier Detect (DCD)
Flashing via OEM WebUI:
1. Download the firmware image *-squashfs-factory.bin
2. Upload firmware image via OEM WebUI firmware update, do not keep settings
To revert back to OEM firmware:
https://wiki.teltonika-networks.com/view/Bootloader_menu
Mobile data connection:
Meig SLM770 create proto DHCP interface with usb0 device.
Quectel EC25-EUX create proto qmi interface.
Marty Jones [Sat, 7 Jun 2025 23:02:25 +0000 (19:02 -0400)]
mac80211: realtek: rtw88: sync with v6.16
Renamed 046..051 pending patches with the merged tag/hash.
Two patches were skipped, they make use of WQ_BH present since v6.14:
https://github.com/torvalds/linux/commit/13221be72034d1c34630ab124c43438aefe7e656
https://github.com/torvalds/linux/commit/3e3aa566dd1803f1697530de6c8489a8350765b3
Manually refreshed 062-v6.14-wifi-rtw88-Add-support-for-LED-blinking.patch
Manually refreshed 063-v6.14-wifi-rtw88-add-RTW88_LEDS-depends-on-LEDS_CLASS-to-K.patch
Manually backported 090-v6.15-wifi-rtw88-Enable-the-new-RTL8814AE-RTL8814AU-driver.patch
git log --no-merges --pretty=oneline --abbrev-commit 4c2c372de...0daa521a drivers/net/wireless/realtek/rtw88: 4c2c372de2e1 wifi: rtw88: fix the 'para' buffer size to avoid reading out of bounds f24d0d8c3cd7 wifi: rtw88: Fix the random "error beacon valid" messages for USB 80fe0bc1659c wifi: rtw88: usb: Upload the firmware in bigger chunks 490340faddea wifi: rtw88: usb: Reduce control message timeout to 500 ms b7f0cc647e52 wifi: rtw88: rtw8822bu VID/PID for BUFFALO WI-U2-866DM 2c17afde9ff6 wifi: rtw88: Handle RTL8723D(S) with blank efuse 0ffa1ba81b35 wifi: rtw88: Fix RX aggregation settings for RTL8723DS 20d3c19bd8f9 wifi: rtw88: do not ignore hardware read error during DPK fc5f5a0ec463 wifi: rtw88: sdio: call rtw_sdio_indicate_tx_status unconditionally b2effcdc2379 wifi: rtw88: sdio: map mgmt frames to queue TX_DESC_QSEL_MGMT 581cf3a9cb61 wifi: rtw88: Fix the module names printed in dmesg b8d49bb8d16a wifi: rtw88: Don't set SUPPORTS_AMSDU_IN_AMPDU for RTL8814AU 0d2a88690e58 wifi: rtw88: Set AMPDU factor to hardware for RTL8814A dcbb7bb3a364 wifi: rtw88: usb: Enable RX aggregation for RTL8814AU bf1103654df9 wifi: rtw88: usb: Enable switching the RTL8814AU to USB 3 625fbc16524a wifi: rtw88: usb: Remove redundant 'flush_workqueue()' calls 5c4cf36c538b wifi: rtw88: sdio: Remove redundant 'flush_workqueue()' calls d58ad77d5cc2 wifi: rtw88: Add __nonstring annotations for unterminated strings deb3ddeb1865 wifi: rtw88: Enable the new RTL8814AE/RTL8814AU drivers bad060e8a425 wifi: rtw88: Add rtw8814au.c dad8e8793102 wifi: rtw88: Add rtw8814ae.c 1a7545784642 wifi: rtw88: Add rtw8814a.{c,h} e38246889cc9 wifi: rtw88: Add rtw8814a_table.c (part 2/2) f4debfcb1b3c wifi: rtw88: Add rtw8814a_table.c (part 1/2) 679ec431477c wifi: rtw88: Add some definitions for RTL8814AU c374281f8285 wifi: rtw88: Extend rtw_debugfs_get_tx_pwr_tbl() for RTL8814AU cfebabdd351e wifi: rtw88: Extend rtw_debugfs_get_phy_info() for RTL8814AU 8b42c46cf665 wifi: rtw88: Extend rtw_phy_config_swing_table() for RTL8814AU 053a7aace020 wifi: rtw88: Fix rtw_rx_phy_stat() for RTL8814AU 6be7544d19fc wifi: rtw88: Fix rtw_init_vht_cap() for RTL8814AU c7eea1ba05ca wifi: rtw88: Fix rtw_init_ht_cap() for RTL8814AU 86d04f8f991a wifi: rtw88: Fix rtw_desc_to_mcsrate() to handle MCS16-31 e66bca16638e wifi: rtw88: Fix rtw_mac_power_switch() for RTL8814AU 80c4668d024f wifi: rtw88: Add support for Mercusys MA30N and D-Link DWA-T185 rev. A1 9f00e2218e15 wifi: rtw88: Fix rtw_update_sta_info() for RTL8814AU 0f98a5959657 wifi: rtw88: Extend TX power stuff for 3-4 spatial streams ad815f392003 wifi: rtw88: Rename RTW_RATE_SECTION_MAX to RTW_RATE_SECTION_NUM e66f3b5c7535 wifi: rtw88: Constify some more structs and arrays 8f0076726b66 wifi: rtw88: Extend rtw_fw_send_ra_info() for RTL8814AU d80e7d9b6ba3 wifi: rtw88: Extend rf_base_addr and rf_sipi_addr for RTL8814AU 62f726848da4 wifi: rtw88: Extend struct rtw_pwr_track_tbl for RTL8814AU 9e8243025cc0 wifi: rtw88: Fix download_firmware_validate() for RTL8814AU 8425f5c8f04d wifi: rtw88: Fix __rtw_download_firmware() for RTL8814AU 105dc94233e4 wifi: rtw88: Fix a typo of debug message in rtw8723d_iqk_check_tx_failed() 0d1d165eff9d wifi: rtw88: Don't use static local variable in rtw8821c_set_tx_power_index_by_rate 00451eb3bec7 wifi: rtw88: Don't use static local variable in rtw8822b_set_tx_power_index_by_rate b4bfbc50b1b9 wifi: rtw88: add RTW88_LEDS depends on LEDS_CLASS to Kconfig 4b6652bc6d8d wifi: rtw88: Add support for LED blinking fb2fcfbe5eef wifi: rtw88: sdio: Fix disconnection after beacon loss a806a8160a0f wifi: rtw88: 8703b: Fix RX/TX issues 5ad483955acc wifi: rtw88: Delete rf_type member of struct rtw_sta_info 5b1b9545262b wifi: rtw88: Add USB PHY configuration
not backported (3e3aa566dd18 wifi: rtw88: usb: Preallocate and reuse the RX skbs)
not backported (13221be72034 wifi: rtw88: Handle C2H_ADAPTIVITY in rtw_fw_c2h_cmd_handle() ) e9048e2935f7 wifi: rtw88: usb: Copy instead of cloning the RX skb 74a72c367573 wifi: rtw88: 8821a/8812a: Set ptct_efuse_size to 0 59ab27a9f20f wifi: rtw88: 8812a: Support RFE type 2
bmips: bcm6358: add support for Huawei HG556a ver A
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR Spansion S29GL128P10
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Atheros AR9223
- 3x USB 2.0 port
- 4x Button
- 13x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg556a-a-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Commit Fixes: 15430a13485b ("bmips: use wan ports as standalone ports")
removed bridge devices and therefore switch.1 no longer exists, so let's
use br-lan instead.
Fixes: 15430a13485b ("bmips: use wan ports as standalone ports") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Andreas Gnau [Fri, 30 May 2025 15:47:57 +0000 (17:47 +0200)]
uboot-mk: Enable specifying defconfig fragments
U-Boot allows specifying additional KConfig fragments to be applied on
top of a defconfig. These are usually located in the board
sub-directory.
make foo_defconfig bar.config baz.config
Add support for specifying additional KConfig fragments using the
UBOOT_CONFIG variable. Treat the first word in UBOOT_CONFIG as the name
of the defconfig, any additional words as additional fragments.
This can be useful to distinguish between different variants of U-Boot
builds such as different RAM, storage (NAND/eMMC), security etc.
While c05c0699d479 (u-boot.mk: add support for config customization,
2023-06-02) already added means to modify specific KConfig options
directly from the OpenWrt Makefile, leveraging existing fragments the
U-Boot source-dir provides a more convenient way to extend the config
when customising more than just one or two options. Furthermore it is
desirable to leverage existing fragments from upstream U-Boot where they
exist.
The Arcadyan WE410443 is a WiFi AC access point distributed by various ISPs
under various names, including KPN SuperWifi and BT Whole Home Wi-Fi. It
features one ethernet port, dual MT7615N radios and four internal antennas.
Installation:
The bootloader is locked with a password, so the image needs to be written
directly to the SPI flash chip. To do this, you need to open up the case,
remove the heatsink and connect the flash chip to a Raspberry Pi. Use the
following connections:
You can solder wires to the flash chip, or use a SOIC16 clip. More details on
the Raspberry Pi and SPI chip pinouts are available on the wiki [1]
When you have the Raspberry Pi connected to the flash chip, boot your Pi and
follow the instructions:
1) Make sure your Pi has SPI enabled with sudo raspi-config
Shiji Yang [Mon, 19 May 2025 23:50:56 +0000 (07:50 +0800)]
ramips: dts: adjust the power regulators of MMC controller
- Fix MMC bus IO voltage. The GPIO voltage of mt762x series SoCs
is fixed 3.3V. There are no visible registers that can control
the voltage level. Also add "no-1-8-v" property to indicate that
MMC controller doesn't support 1.8V IO.
- Drop useless property "enable-active-high". These dummy fixed
voltage regulators are not controlled by the GPIO. We don't need
to set the GPIO polarity.
Shiji Yang [Mon, 19 May 2025 23:50:56 +0000 (07:50 +0800)]
ramips: dts: mt7621: add the missing XHCI power regulators
The USB power regulators are essential for the Mediatek XHCI
controller. If any of them is missing, the kernel will throw
a warning. Add fixed voltage io/vbus regulators to workaround
this issue. Fix the following warnings:
[ 7.514572] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator
[ 7.522375] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
MAC Addresses in OEM firmware:
- There is one on the label, e.g. AA:BB:CC:DD:EE:FF
- WLAN (2.4G) uses the same as on the label
- WLAN (5G) is the one on the label but
- first byte (e.g. AA) + 2
- fourth byte (e.g. DD) - 0x40
- WAN is the one on the label + 1
- LAN is the one on the label
MAC Addresses in OpenWrt:
- Same handling as in WR3000s is used
GPIO:
- 2 Buttons (all low active):
- WPS on GPIO 0
- Reset on GPIO 1
- 6 LEDs (all low active):
- Power: Blue on GPIO 8, no red LED
- WPS: Blue on GPIO 10, Red on GPIO 4
- Internet: Blue on GPIO 11, no red LED
- LAN: Blue on GPIO 9, Red on GPIO 5
- WiFi 2.4G: Blue on GPIO 6, no red LED
- WiFi 5G: Blue on GPIO 7, no red LED
Disassembly:
- Remove the 4 screws at the bottom of the case
- Cover is clipped to the bottom part of the case with clips in the front and the back
UART:
- UART pins are accessible on the bottom of the board
- The connector with the square shape is TX
- Pins: [ ] TX, ( ) RX, ( ) GND, ( ) VCC
- Settings: 115200 8N1 3.3V
Migration to OpenWrt via OEM firmware:
- There should be a migration image available from Cudy as soon as there is official OpenWrt support
- Download the migration image via OEM web interface
- After flashing, OpenWrt is accessible via 192.168.1.1
- Flash the official OpenWrt image
Migration to OpenWrt using TFTP:
- Connect UART as described above
- Press the reset button while powering on the device
- U-Boot will now try to load a recovery.bin via TFTP, this must be ignored
- After detecting a timeout, the U-Boot console is available via UART
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the initramfs image via TFTP as cudy3000e.bin
- Run the following command in U-Boot: tftpboot 0x46000000 cudy3000e.bin; bootm 0x46000000
- OpenWrt initramfs image is now booting and accessible via 192.168.1.1
- Flash the sysupgrade image
Revert back to OEM:
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the Cudy firmware via TFTP as recovery.bin
- Press the reset button while powering on the device
- Recovery process will start now
- After recovery is done, the OEM firmware is available at 192.168.10.1 again
Benjamin Berg [Wed, 4 Jun 2025 19:00:03 +0000 (21:00 +0200)]
wifi-scripts: add missing entries for mesh_nolearn
The plumbing is there in the ucode files to set the parameter using
nl80211. However, the option is never forwarded because it was missing
in mac80211.sh. Add it there and in the schema file.
Robert Marko [Sat, 7 Jun 2025 09:53:48 +0000 (11:53 +0200)]
netifd: update to Git HEAD (2025-05-23)
61ae5732adea iprule: amend ipproto netlink nla_put_u32 to nla_put_u8 d610d68c71b8 device: add support for configuring vrf a1b6386a20a6 device: fix bonding primary port selection e8bbf246ce2e system-linux: fix sysfs name for all_ports_active flag 723c699e84f4 Restore disable_ipv6 sysctl after removing a device from bridge or bond d476e18e8d43 iprule: resolve ipproto by name 7901e66c5f27 netifd: iprule add sport and dport
Jonas Gorski [Wed, 4 Jun 2025 08:32:29 +0000 (10:32 +0200)]
bmips: use wan ports as standalone ports
With the recent fixes backported to 6.12, b53 ports should now fully
work as standalone ports outside of a switch.
So move them out of the switch and use them as standalone ports, which
makes configuring easier as VLANs don't need to be defined and reserved
anymore to use the wan port.
Tested on DGND3700v1.
While most devices do not define a wan port, I dropped the
ucidef_set_bridge_device() from all devices for consistency.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tim Harvey [Fri, 6 Jun 2025 16:04:39 +0000 (09:04 -0700)]
imx: 6-12: refresh patches and kernel configs
patches:
- remove patches from 6.7-6.12 that are now upstream.
- refresh remaining patches
- 502-6.13-arm64-dts-freescale-rename-gw7905-to-gw75xx.patch was
misnamed as that patch went upstream in 6.12 and thus is also removed
- 504-6.13-arm64-dts-imx-Add-i.MX8M-Plus-Gateworks-GW82XX-2X-support.patch
was refreshed to the final version that was accepted upstream
- 600-PCI-imx6-Start-link-at-max-gen-first-for-IMX8MM-and-IMX8MP.patch
was removed while I investigate an upstream approach for the issue
it was working around.
configs:
- config-6.12: unset new configs not needed for all cortexa7/a9/a53
- cortexa53/config-default: added new CONFIG_PCI_IMX6_HOST config for cortexA53 (IMX8M)
Tim Harvey [Thu, 5 Jun 2025 15:16:57 +0000 (08:16 -0700)]
kernel/imx: Restore kernel files for v6.6
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
projects / thirdparty / openwrt.git / log
