Disassembly:
At the bottom, under the LEDs, there are 2 screws hidden by rubber feet. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it.
Serial Interface:
The serial interface can be connected to the 5 pin dots located on the right between the operating mode switch and the antenna.
Pins (from antenna to operating mode switch):
VCC
TX
RX
NC
GND
Settings: 115200, 8N1
Flashing via OEM recovery software:
1. Download the OEM recovery software from the manufacturer's website
2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1212_recovery.bin
3. Replace the file in the fw folder OEM recovery software with the file from step 2.
4. Run the OEM recovery software and follow the instructions.
Flashing via TFTP:
1. Connect your PC and router to port 1-3, configure PC interface using IP 192.168.1.2, mask 255.255.255.252
2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1212_recovery.bin via TFTP
3. Power up the router while pressing Reset button on the back
4. Release Restart button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image.
When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size.
Until now the timer management on the RTL931x devices depends
on the MIPS default timer. Looking at the clock progress on
these devices one can see that it is totally off. It is running
at half the required speed (e.g. if 1 minute passes the date
command shows that according to the timers only 30 seconds have
elapsed). This is a mix from wrong DTS and bad startup code.
This is not only a cosmetic issue but has effects on every
delay operation inside the kernel. Switch RTL931x to the proven
Otto timer.
Upstream has gained support for forced affinity settings in the MIPS
GIC interrupt controller. This is needed to enable the Otto timer on
the RTL931x platform. See
Check Point V-80 (Quantum Spark 1590 Appliance) is an Appliance, based
on Armada 8040 (88F8040).
Specification:
- SoC : Marvell Armada 8040 (88F8040)
- RAM : DDR4 2 GiB (4x 512 MiB chip)
- Flash : eMMC 4 GiB
- Ethernet : 10x 10/100/1000 Mbps
- LAN 1-8 : Marvell 88E6393X
- WAN : Marvell 88E1512
- DMZ : Marvell 88E1512 (RJ-45/SFP combo)
- LEDs/Keys (GPIO): 11x/1x
- UART : "CONSOLE" port (USB 1.1 Type-C)
- chip : Silicon Labs CP2102N
- port : ttyS0
- settings : 115200bps 8n1
- HW Monitoring : 2x nuvoTon NCT7802Y
- USB : USB 3.0 Type-A
- Power : 12 VDC, 3.3 A
- plug : DC Plug 2.5/5.5 mm (inner/outer)
Flash instruction (common):
1. Boot V-81 normally
2. Login to the vendor CLI (default: admin/admin) and login to the Linux
CLI by `expert` command
3. Update U-Boot environment variables by the following commands
Attention: don't forget single quatations of values to prevent
expansion of variables
4. Turn off the device
Flash instruction (USB-boot/SD-boot):
1. Extract and burn (squashfs|ext4)-sdcard.img.gz to USB storage or
MicroSD card
2. Connect that storage to V-81
3. Turn on V-81 and it will be booted with OpenWrt in that USB storage
Flash instruction (eMMC-boot):
1. Copy initramfs image, dtb and bootsctipt to the USB storage with
renaming
2. Connect that storage to the USB 3.0 port on V-81
3. Turn on V-81 and it will be booted with OpenWrt initramfs image in
that USB storage
4. Upload (squashfs|ext4)-sysupgrade.gz to V-81
5. Perform sysupgrade with the uploaded image
6. Wait ~100 seconds to complete flashing
Reverting to stock firmware:
1. Turn on V-81 and interrupt booting by Ctrl + C
2. Select "4. Restore to Factory Defaults (local)"
3. Wait ~180 seconds to complete restoring and rebooting
Notes:
- The partition table in the internal eMMC has single partition, but
"blkdevparts=" parameter will be passed from the bootloader and that
definition will be used instead.
- The port-side LED pairs of RJ-45/SFP ports on V-81 are switched by a
GPIO pin of pin7 on &cp0_gpio2. (High(1): RJ-45, Low(0): SFP)
This needs to be switched manually.
- The MicroSD card slot is too unstable and the following messages are
printed without "marvell,xenon-phy-slow-mode;" property.
- There are no detailed information about maximum power consumption
limit of the SFP port or optional DSL-SFP modules sold officially.
But the power requirement of almost DSL-SFP modules are 3.3V/700mA, so
set the maximum value of the SFP port to 2000 mW (Power Level III).
- Do not insert a MicroSD card before turning of the device when OpenWrt
installation. The stock firmware deletes all files in the first
partition automatically, to use it as a storage for logs.
Check Point V-80 (Quantum Spark 1550 Appliance) is an Appliance, based
on Armada 7040 (88F7040).
Specification:
- SoC : Marvell Armada 7040 (88F7040)
- RAM : DDR4 2 GiB (4x Nanya NT5AD512M8D3-HR)
- Flash : eMMC 4 GiB (Toshiba THGBMNG5D1LBAIL)
- Ethernet : 6x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6352
- WAN : Marvell 88E1512
- LEDs/Keys (GPIO): 6x/1x
- UART : "CONSOLE" port (USB 1.1 Type-C)
- chip : Silicon Labs CP2102N
- port : ttyS0
- settings : 115200bps 8n1
- HW Monitoring : 2x nuvoTon NCT7802Y
- USB : USB 3.0 Type-A
- Power : 12 VDC, 3.3 A
- plug : DC Plug 2.5/5.5 mm (inner/outer)
Flash instruction (common):
1. Boot V-80 normally
2. Login to the vendor CLI (default: admin/admin) and login to the Linux
CLI by `expert` command
3. Update U-Boot environment variables by the following commands
Attention: don't forget single quatations of values to prevent
expansion of each variables
4. Turn off the device
Flash instruction (USB-boot):
1. Burn (squashfs|ext4)-sdcard.img.gz to USB storage
2. Connect that storage to the USB 3.0 port on V-80
3. Turn on V-80 and it will be booted with OpenWrt in that USB storage
Flash instruction (eMMC-boot):
1. Copy initramfs image, dtb and bootsctipt to the USB storage with
renaming
2. Connect that storage to the USB 3.0 port on V-80
3. Turn on V-80 and it will be booted with OpenWrt initramfs image in
that USB storage
4. Upload (squashfs|ext4)-sysupgrade.gz to V-80
5. Perform sysupgrade with the uploaded image
6. Wait ~100 seconds to complete flashing
Reverting to stock firmware:
1. Turn on V-80 and interrupt booting by Ctrl + C
2. Select "4. Restore to Factory Defaults (local)"
3. Wait ~180 seconds to complete restoring and rebooting
Notes:
- V-80 has some HW versions. Internal MicroSD card slot and mPCIe slot
is available on some HW versions, but not on the other HW versions.
confirmed (MicroSD/mPCIe slots):
- 1.0.1: unavailable
- 1.0.3: available
- The partition table in the internal eMMC has single partition, but
"blkdevparts=" parameter will be passed from the bootloader and that
definition will be used instead.
Installation:
Cudy has distributed intermediate firmware to make installation easier
1. Go to [Cudy CN official website](https://www.cudy.com/zh-cn/pages/download-center/tr3000-1-0) and download the intermediate firmware
2. Upgrade the intermediate firmware on the page
3. Visit the intermediate firmware 192.168.1.1 webpage and use the sysupgrade image to update
other:
If you fail to flash the device, you can use TFTP to flash back to the original firmware.
1. Ask Cudy CN official customer service for the original firmware
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an recovery.bin firmware file.
realtek: make use of serdes helper for Zyxel GS1900-24(HP) v1/v2
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
realtek: make use of serdes helper for D-Link DGS-1210-26
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
realtek: make use of serdes helper for D-Link DGS-1210-10P
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
realtek: make use of serdes helper for Zyxel GS1900-10HP
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
realtek: make use of serdes helper for TP-Link SG2xxx
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
realtek: make use of serdes helper for Panasonic M8EG PN28080K
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
realtek: make use of serdes helper for Netgear GS310TP v1
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
REMARK! The original commit c829bc1f2c3c47e2 ("realtek: Add support for
Netgear S350 series switches GS308T and GS310TP") says that the SFP
ports are untested. Looking at device internal pictures from
https://techinfodepot.shoutwiki.com/wiki/Netgear_GS310TP there are no
external phys for the SFP ports. So fix port description.
realtek: make use of serdes helper for HPE 1920 8G
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
realtek: make use of serdes helper for Engenius EWS2910P
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
realtek: make use of serdes helper for D-Link DGS-1210-10MP
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
realtek: make use of serdes helper for Linksys LGS310C
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
This indicates that the link is driven by a serdes directly without
external phy. As the devices have multiple serdes it must be clarified
what serdes is responsible for that port.
Nevertheless all other devices have the same requirements. E.g. RTL838x
usually drives port 24 from serdes 4 and port 26 from serdes 5. All this
currently works because the driver has a lot of hardcoded port/serdes
mapping.
Make the situation better by adding dts helpers that can describe the
topology as needed.
Eric Fahlgren [Mon, 9 Jun 2025 23:59:13 +0000 (16:59 -0700)]
package: include abiversion tag in package metadata
OpenWrt library packages are often named using their ABI version,
for example 'libubus20250102'. Updates that cause the ABI version
to change result in changes to the package name. This makes it
impossible for downstream tools to determine when a package update
is available without further information.
The opkg package manager stores the ABI version as part of its
package metadata in the ABIVersion field. This makes extraction
of the canonical name of the package possible, allowing various
versions of a package to be associated with one another, their
versions or build dates compared.
We add a custom tag 'openwrt:abiversion=<ABI version>' to the
apk v3 package metadata, restoring the status quo and making it
functionally backwards compatible with opkg (the tag format was
selected per the guidelines in the apk-tools documentation).
Zheng Zhang [Sat, 14 Jun 2025 14:56:04 +0000 (22:56 +0800)]
qualcommbe: enable CONFIG_THERMAL and CONFIG_THERMAL_HWMON
The Qualcomm TSENS driver only exposes sensors to as a thermal
zone without registering hwmon, making these temperature sensors
unreadable by lm-sensors. This commit enables CONFIG_THERMAL and
CONFIG_THERMAL_HWMON for qualcommbe target to access the sensors
from hwmon.
Suggested-by: Yao Zi <ziyao@disroot.org> Signed-off-by: Zheng Zhang <everything411@qq.com> Link: https://github.com/openwrt/openwrt/pull/19137 Signed-off-by: Robert Marko <robimarko@gmail.com>
Zheng Zhang [Sun, 15 Jun 2025 00:34:26 +0000 (08:34 +0800)]
qualcommax: enable CONFIG_THERMAL and CONFIG_THERMAL_HWMON
The Qualcomm TSENS driver only exposes sensors to as a thermal
zone without registering hwmon, making these temperature sensors
unreadable by lm-sensors. This commit enables CONFIG_THERMAL and
CONFIG_THERMAL_HWMON for qualcommax targets to access the sensors
from hwmon.
Suggested-by: Yao Zi <ziyao@disroot.org> Signed-off-by: Zheng Zhang <everything411@qq.com> Link: https://github.com/openwrt/openwrt/pull/19137 Signed-off-by: Robert Marko <robimarko@gmail.com>
xiao bo [Sun, 22 Jun 2025 01:29:15 +0000 (09:29 +0800)]
kernel: remove expired i40evf drivers
In the development history of Intel's drivers, the i40evf driver was later
renamed the iavf driver. For example, some documents mention that
Intel® Network Connections Software Version 24.0 renamed the i40evf
and ixlv drivers to iavf. In subsequent versions, the i40evf driver was
gradually removed, and its functions were taken over by the iavf driver.
In the Linux system, relevant configuration instructions also exist. For
instance, the User Guide for X722 Onboard Network Card states that the
i40evf driver module should be disabled, and the iavf driver should be
installed and used.
Thomas Richard [Mon, 5 May 2025 08:28:59 +0000 (10:28 +0200)]
kernel/stm32: Restore kernel files for v6.6
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Shiji Yang [Tue, 29 Apr 2025 12:09:09 +0000 (20:09 +0800)]
x86: refresh kernel symbol configs
All kernel config symbols are refreshed by `make kernel_oldconfig`.
Some symbols are moved to the generic/config-6.12 because the
refresh tool will automatically trim them.
Change deprecated function strlcpy to strscpy
for compatibility with kernel 6.12.
strlcpy() reads the entire source buffer first.
This read may exceed the destination size limit.
This is both inefficient and can lead to linear read
overflows if a source string is not NUL-terminated [1].
In an effort to remove strlcpy() completely [2], replace
strlcpy() here with strscpy().
Direct replacement is safe here since DEV_ASSIGN is only used by
TRACE macros and the return values are ignored.
realtek: activate MIPS power cluster controller for RTL931x
The SMP environment is prepared well for the RTL93X. Now describe the
power cluster controller in the DTS. Tested on RTL9311 based Linksys
LGS352C.
Without patch:
root@OpenWrt:~# dmesg | grep CPU
[ 0.140425] CPU1 revision is: 0001a120 (MIPS interAptiv (multi))
[ 0.191952] Synchronize counters for CPU 1: done.
[ 1.232191] CPU2: failed to start
[ 1.237863] No online CPU in core 1 to start CPU3
[ 2.273784] CPU3: failed to start
[ 2.277589] smp: Brought up 1 node, 2 CPUs
root@OpenWrt:~# cat /proc/cpuinfo | grep -E "model|proc"
processor : 0
cpu model : MIPS interAptiv (multi) V2.0
processor : 1
cpu model : MIPS interAptiv (multi) V2.0
With patch:
root@OpenWrt:~# dmesg | grep CPU
[ 0.000000] CPU0 revision is: 0001a120 (MIPS interAptiv (multi))
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Failed to get CPU clock: -2
[ 0.000000] CPU frequency from device tree: 1000MHz
[ 0.133360] smp: Bringing up secondary CPUs ...
[ 0.140418] CPU1 revision is: 0001a120 (MIPS interAptiv (multi))
[ 0.191950] Synchronize counters for CPU 1: done.
[ 0.230103] CPU2 revision is: 0001a120 (MIPS interAptiv (multi))
[ 0.289220] Synchronize counters for CPU 2: done.
[ 0.326189] CPU3 revision is: 0001a120 (MIPS interAptiv (multi))
[ 0.378861] Synchronize counters for CPU 3: done.
[ 0.413829] smp: Brought up 1 node, 4 CPUs
processor : 0
cpu model : MIPS interAptiv (multi) V2.0
processor : 1
cpu model : MIPS interAptiv (multi) V2.0
processor : 2
cpu model : MIPS interAptiv (multi) V2.0
processor : 3
cpu model : MIPS interAptiv (multi) V2.0
Introduced with Linux 6.7, in commit: 5c2f7727d437 ("mtd: mtdpart: check for subpartitions parsing result"),
when a parser returns an error, this will be passed up, and
consequently, all parent mtd partitions get torn down.
Adjust the mtdsplit_uimage driver to only return an error if there is a
critical problem in reading from the mtd device or allocating memory.
Otherwise return 0 to indicate that no partitions were found.
Also add logging to indicate what went wrong.
E.g. on Realtek devices that are booted for the first time through
initramfs with OpenWrt never installed before boot log will show
[ 0.975518] Creating 7 MTD partitions on "spi0.0":
[ 0.981062] 0x000000000000-0x0000000e0000 : "u-boot"
[ 1.041320] 0x0000000e0000-0x0000000f0000 : "u-boot-env"
[ 1.060683] 0x0000000f0000-0x000000100000 : "u-boot-env2"
[ 1.080992] 0x000000100000-0x000000200000 : "jffs2-cfg"
[ 1.100988] 0x000000200000-0x000000300000 : "jffs2-log"
[ 1.120599] 0x000000300000-0x000000fe0000 : "firmware"
[ 1.157426] mtdsplit_uimage: no rootfs after uImage in "firmware"
[ 1.176456] mtdsplit_uimage: no rootfs after uImage in "firmware"
[ 1.200262] 0x000000fe0000-0x000001000000 : "log"
Similar issues were fixed before with commit ade045084bd3f8696
("kernel: mtdsplit_minor: return 0 if not fatal") and c78765213ecbe830204 ("kernel: mtdsplit_uimage: return 0 if not fatal")
Valeriy Manzhos [Sun, 15 Jun 2025 10:08:29 +0000 (13:08 +0300)]
ath79: enable USB by default on hAP ac
Due to a bug, USB is not powered on after boot on hAP ac.
This prevents extroot configurations from working as overlayfs is mounted
before USB device can be powered on. This commit fixes this by enabling USB
in devicetree.
Related discussion links:
- https://forum.openwrt.org/t/usb-power-is-off-on-boot/229007
---
Extroot configuration requires the USB to be powered on before
preinit_main/80_mount_root. Probably the simplest approach is to enable
it in the devicetree. Another approach would be to add a script into
/lib/preinit that will power on USB via /sys/class/gpio/usb-power/value
E.g.
cat /lib/preinit/79_power_on_usb
do_power_on_usb(){
echo '1' > /sys/class/gpio/usb-power/value
}
boot_hook_add preinit_main do_power_on_usb
Yijie Jin [Sat, 28 Dec 2024 07:00:28 +0000 (15:00 +0800)]
ramips: mt7621: add support for JDCloud RE-SP-01B
JDCloud RE-SP-01B is a dual-band WiFi 5 router based on the MT7621AT.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 512MB DDR3
- Flash: 32MB SPI NOR
- WiFi: MediaTek MT7603EN (2.4GHz), MediaTek MT7615N (5GHz)
- Ethernet: 1x WAN, 2x LAN (Gigabit Ethernet)
- LEDs: red, blue, green (GPIO controlled)
- Button: Reset (GPIO controlled)
- eMMC: Single onboard (32GB/64GB/128GB)
- USB: 1x USB 2.0 port
MAC Address Structure:
The MAC addresses share the structure DC:D8:7C:XX:XX:XX, where:
- WAN, LAN, and 2.4GHz WiFi: same as the label MAC address.
- 5GHz WiFi: label MAC address + 0x800000.
The manufacturer writes the label MAC address at different
offsets depending on the storage version of the device:
Flash Instruction:
A 3rd party bootloader is required to boot the image. You can
use a SOP16 test clip to burn the image/bootloader to the flash.
The official bootloader does provide a web recovery interface
which only accepts an official image. To access it, you will
need to hold the reset button and power on the device, set your
IP address to 192.168.68.2 and visit http://192.168.68.1.
Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn> Signed-off-by: Yijie Jin <jinyijie@outlook.com> Link: https://github.com/openwrt/openwrt/pull/17409 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
realtek: fix/add switchcore syscon nodes for RTL838x/RTL839x/RTL931x
The switchcore node is the central location that describes the Realtek switch
register addresses starting at 0x1b000000. It will be used by current and
future regmap enabled device drivers. The upstream MDIO driver already makes
use of it by calling syscon_node_to_regmap(dev->parent->of_node);
In the current DTS base we have 3 issues that should be fixed:
- rtl838x.dtsi has a length of 0x20000 instead of 0x10000
- rtl839x.dtsi has a length of 0x20000 instead of 0x10000
- rtl931x.dtsi has no switchcore node at all
Align these mismatches with the "good" RTL930x template.
Jonas Jelonek [Mon, 16 Jun 2025 19:57:27 +0000 (19:57 +0000)]
realtek: rtl931x: fix I2C sda pin
The drivers for I2C bus and mux for RTL931x have an incorrectly defined
SDA0 pin number, causing an error with correct pin numbers specified in
the device tree.
Using the `show tech-support board` on the vendor firmware of a Netgear
MS510TXM shows the correct pin numbers but they don't work with the
drivers. So fix this.
Jonas Jelonek [Wed, 18 Jun 2025 09:52:02 +0000 (09:52 +0000)]
realtek: rtl931x: add missing function reference for l2_hash_seed
Add missing function reference for the l2_hash_seed call in rtl931x_reg
in the rtl83xx DSA driver part.
While at it, rename the referenced function to proper naming convention
and simplify its content.
The missing reference causes a hard crash after a short time (on
MS510TXM) because the driver assumes the reference always exists.
Shiji Yang [Mon, 17 Mar 2025 16:42:19 +0000 (00:42 +0800)]
ramips: PCIe driver improvements for mt7620 and mt7628
This patchset fixes some PCIe bridge register access issues and
reworks the initialization procedure. It may bring some stability
improvements. To match the driver changes, the memory remap range
was extended and a PCIe reset pinctrl was added to mt7628an.dtsi.
Jonas Gorski [Wed, 18 Jun 2025 08:46:35 +0000 (10:46 +0200)]
iproute2: point KERNEL_INCLUDE to toolchain headers
Glibc since 2.41 tries to include linux/sched/types.h from sched.h, and
pointing KERNEL_INCLUDE to the kernel headers makes it use
linux/sched/types.h from the kernel headers instead of the installed
one.
This then breaks the configure (test) compile for setns() and the test:
mips-openwrt-linux-gnu-gcc -I/fork.openwrt/build_dir/target-mips_24kc_glibc/linux-ath79_generic/linux-6.6.93/include/uapi -o config.HaAJYe/setnstest config.HaAJYe/setnstest.c
In file included from /fork.openwrt/build_dir/target-mips_24kc_glibc/linux-ath79_generic/linux-6.6.93/include/uapi/linux/sched/types.h:5,
from /fork.openwrt/staging_dir/toolchain-mips_24kc_gcc-14.3.0_glibc/include/bits/sched.h:63,
from /fork.openwrt/staging_dir/toolchain-mips_24kc_gcc-14.3.0_glibc/include/sched.h:43,
from config.HaAJYe/setnstest.c:2:
/fork.openwrt/build_dir/target-mips_24kc_glibc/linux-ath79_generic/linux-6.6.93/include/uapi/linux/types.h:10:2: warning: #warning "Attempt to use kernel headers from user space, see https://kernelnewbies.org/KernelHeaders" [-Wcpp]
10 | #warning "Attempt to use kernel headers from user space, see https://kernelnewbies.org/KernelHeaders"
| ^~~~~~~
In file included from /fork.openwrt/build_dir/target-mips_24kc_glibc/linux-ath79_generic/linux-6.6.93/include/uapi/linux/posix_types.h:5,
from /fork.openwrt/build_dir/target-mips_24kc_glibc/linux-ath79_generic/linux-6.6.93/include/uapi/linux/types.h:14:
/fork.openwrt/build_dir/target-mips_24kc_glibc/linux-ath79_generic/linux-6.6.93/include/uapi/linux/stddef.h:5:10: fatal error: linux/compiler_types.h: No such file or directory
5 | #include <linux/compiler_types.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.
Fix this by pointing KERNEL_INCLUDE to the toolchain headers, which
include the installed kernel headers.
Tested with musl, glibc, and SDK.
Fixes: 60738feded ("iproute2: Fix KERNEL_INCLUDE in SDK") Reported-by: Signed-off-by: Konstantin Demin <rockdrilla@gmail.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
realtek: add new i2c-gpio-shared driver for shared SCL lines
Some Realtek switches have been designed with I2C busses that share a
single SCL line. The clock line is used for 2 or more busses. This cannot
be used with the standard i2c-gpio driver that relies on distinct SDA
and SCL pairs.
Provide a derived i2c-gpio-shared driver that can be used instead. This
driver can handle up to 4 busses with only a single clock line.
Josef Schlehofer [Fri, 13 Jun 2025 14:32:45 +0000 (16:32 +0200)]
perf: disable slang support
libs/slang2 is getting picked up from the packages feed, if the slang2
is compiled first and then if you try to compile perf, it fails
due to unmet dependency.
Fixes:
Package perf is missing dependencies for the following libraries:
libslang.so.2
projects / thirdparty / openwrt.git / log
