Fix Totolink X6000R image failing to upgrade via sysupgrade due to an
incorrect upgrade case. The fallback upgrade path used the NAND upgrade
routine, which caused the "layout volume not found" error on NOR flash
devices. By adding a specific case for this board, sysupgrade now uses
`default_do_upgrade`, which is compatible with the NOR flash layout.
Ari Kurniawan [Mon, 15 Sep 2025 13:13:29 +0000 (20:13 +0700)]
mediatek: filogic: add support for Totolink X6000R
Specification :
- SOC : Mediatek MT7981B (1.3GHz)
- RAM : 256MB
- Flash : 16MB SPI NOR
- Ports : 4 LAN (1G) & 1 WAN (1G)
- WIFI : MediaTek dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Buttons : Reset & WPS/Mesh
- LEDS : WAN (Green), Status (Red & Blue)
- Power : 12V1A
Install via OEM web ui:
Upload the sysupgrade image to firmware upgrade page on OEM web ui
Install via recovery / revert to stock firmware:
1. Unplug from power
2. Download the Sysupgrade (for openwrt installation) or OEM Factory image (for revert to stock firmware)
3. Set your computer ethernet IP to 192.168.1.X, subnet 255.255.255.0 (X=your chosen ip number ranging from 2-254)
4. Press and hold reset button while turn on / plug power adapter to the router. Wait untill ALL LAN green LED turn on, then release the reset button.
5. Plug the LAN cable from your computer into LAN 1 port then open web browser, and type in the address column : 192.168.1.1
6. Upload the sysupgrade / oem factory image
7. Wait until the router finished flashing (the router will reboot)
8. Set ethernet ip to dhcp
9. Open 192.168.1.1 (for openwrt install) / 192.168.0.1 (for OEM firmware)
Florian Maurer [Fri, 3 Oct 2025 07:30:59 +0000 (09:30 +0200)]
ath11k: fix transmit queue flushing through flush_sta implementation
warning print "ath11k c000000.wifi: failed to flush transmit queue 0"
is observed during busy times.
The mac80211 fallback implementation of `flush_sta` does not handle the per STA queues well.
This is fixed by providing a ath11k specific implementation of flush_sta telling the firmware to flush a given station.
The draining of the transmit queues should therefore stop correctly, even if new packets arrive in the mean time.
An upstream ath11k RFC is available at:
https://patchwork.kernel.org/project/linux-wireless/patch/GV1P250MB14333A5BF24623C4753A10E1E8E0A@GV1P250MB1433.EURP250.PROD.OUTLOOK.COM/
Shine [Wed, 10 Dec 2025 23:21:48 +0000 (00:21 +0100)]
mpc85xx: p1010: Use zImage loader for Watchguard Firebox T10
Since kernel 6.1, the Watchguard Firebox T10 can't boot anymore due to
increased kernel size.
This commit introduces the zImage loader from 7d768a9 to boot the kernel.
This is required, since the U-Boot version used in this device appears
to have a hard limit of 16MB for the kernel size it can handle. The
current kernel size is around 17MB, though, due to kernel page alignment
required for memory protection.
Marcin Leksmark [Wed, 12 Nov 2025 20:39:56 +0000 (21:39 +0100)]
ramips: fix support for Cudy r700
This PR fixes support for Cudy r700.
Original PR: https://github.com/openwrt/openwrt/pull/18532
Fixed:
- WAN port functionality;
- RESET button;
- Status LED;
- LAN port names consistent with the chassis;
- Merged partitions "debug", "backup" & "firmware" to one partition "firmware" ("debug" & "backup" contained unimportant data);
- Removed redundant DTS elements.
Installation:
To install OpenWRT, you need the intermediate firmware from Cudy. (U-boot is locked). After installing the intermediate firmware, you can install OpenWRT via sysupgrade.
Recovery:
TFTP available.
1. Place the recovery.bin in the serving directory of your TFTP server.
2. Set your IP to 192.168.1.88/24.
3. Press the “Reset” button of Cudy router and hold it. Before the Cudy router is powered on and before TFTP start to download the firmware, don't release the “Reset” button.
4. Power on the Cudy router.
5. You can release the reset button only when TFTP starts downloading firmware.
6. When the SYSTEM LED turns solid green, the upgrade is complete.
Marcin Leksmark [Sat, 6 Dec 2025 13:43:22 +0000 (14:43 +0100)]
ramips: add support for Cudy C200P
This patch adds support for Cudy C200P.
Because v24.10 stable has no regulator definition, so we cannot make simple cherry-pick. We need another DTS file.
Switch: 1 WAN, 4 LAN (Gigabit)
Gigabit RJ45 PoE Ports on 2~5
Max Power on a Single PoE Ports 30W
PoE Ports : The PoE ports comply with IEEE 802.3at/af standards.
Ports: 1 USB-A 3.0 Ports
LED:
System
PoE Max Status
Link/ACT/PoE Status of Each PoE Port
Physical Buttons:
Reset Button
Power Input:
DC Jack
Power Methods:
DC: 54V 1.11A
802.3at/af PoE
Passive PoE: 24/48V
Max Power Consumption (W):
Total: 60W
PoE: 55W
PoE (when USB Device is plugged in): 50W
No PoE: 5W
Installation:
To install OpenWRT, you need the intermediate firmware from Cudy. (U-boot is locked). After installing the intermediate firmware, you can install OpenWRT via sysupgrade.
Recovery:
TFTP available.
1. Place the recovery.bin in the serving directory of your TFTP server.
2. Set your IP to 192.168.1.88/24.
3. Press the “Reset” button of Cudy router and hold it. Before the Cudy router is powered on and before TFTP start to download the firmware, don't release the “Reset” button.
4. Power on the Cudy router.
5. You can release the reset button only when TFTP starts downloading firmware.
6. When the SYSTEM LED turns solid green, the upgrade is complete.
Serial:
1. Serial connection parameters: 115200 / 8N1
2. Serial connection voltage: 3.3V
PoE is not supported at the time of PR. The IP804R chip is not yet supported by OpenWRT.
Coia Prant [Wed, 1 Oct 2025 10:04:26 +0000 (18:04 +0800)]
ramips: add support for Hongdian H8850 v20
This is an industrial 4G router equipped with OpenWrt SNAPSHOT OEM
customized version
WARNING: The original firmware device tree is modified from evb
boards, and the device tree name is evb board. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Issue:
- Factory partition not store mac address on original firmware
Flash instruction:
Using TTL:
1. Connect the board to the computer via TTL.
2. Enter original firmware failsafe mode.
3. Use wget download firmware to board /tmp
4. Use command "mtd -r write openwrt-ramips-mt76x8-hongdian_h8850-v20-squashfs-sysupgrade.bin firmware"
to flash
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h8850-v20-and-flash.html
GL-MV1000 external SD controller was broken by a recent kernel update
between OpenWRT releases 24.10.2 and 24.10.3 due to a mistake in Device
Tree: "regulator-gpio" was defined without required "gpios" property.
Since "no-1-8-v" property is also defined for this controller
a switchable vqmmc-supply regulator performs no function - a fixed 3.3V
IO voltage will always be used.
This regulator definition was probably added by mistake from a Device
Tree from another device.
Remove incomplete vcc_sd_reg1 regulator definition to fix this issue.
Issue discussion for reference: openwrt/openwrt#20309
1. Download or make the OpenWrt initramfs.trx image
2. Connect the PC via LAN to one of the yellow router ports and wait until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1/
4. If your router is brand new, finish the setup process and log into the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using SCP and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
TFTP Method:
1. Download the OpenWrt initramfs image.
Copy the image to a TFTP server reachable at 192.168.1.70/24.
Rename the image to tufax4200q.bin.
2. Connect the PC with TFTP server to the TUF-AX4200Q.
Set a static ip on the ethernet interface of your PC.
(IP address: 192.168.1.70, subnet mask: 255.255.255.0)
Connect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
Backport upstream commit that fixes handling of multicast packets.
Without this patch, ARP resolution fails, and connectivity from a
station to an AP does not work reliably until traffic is initiated
by the AP.
Marcin Leksmark [Thu, 11 Sep 2025 14:40:20 +0000 (16:40 +0200)]
ramips: add support for D-Link DIR-2660 A2
This patch adds support for D-Link DIR-2660 A2.
Based on the commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=b5dd746cbb1aaf91f4b68e9f3eda97413550d904,
Both devices look identical, except for the A1/A2 designation.
You can safely install the A1 firmware for the A2 – I've been testing it for several months as a DUMB AP – without any problems.
Specifications:
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white), USB 2.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
Andreas Gnau [Wed, 10 Dec 2025 17:21:45 +0000 (18:21 +0100)]
build: depend on tools/zstd for download
Downloading packages from git requires zstd to compress their tarballs.
Make sure that zstd from host tools is compiled when running make
download. Otherwise, either the download would fail because zstd is not
present or a random version from the host would be used leading to hash
mismatches.
Tianling Shen [Thu, 13 Nov 2025 13:41:30 +0000 (21:41 +0800)]
mediatek: fix ubi size for zbtlink zbt z8102ax v2
According to the factory uboot and firmware[1], the ubi size is set
to 512 MiB (0x20000000) and it exceeds the size of the flash, after
that the uboot and kernel resizes it to 114.5 MiB (0x7280000) instead
of 114.125 MiB (0x7220000). The mismatch of the ubi size causes
kernel fails to read ubi volumes and throws panic.
Shine [Tue, 11 Nov 2025 18:49:16 +0000 (19:49 +0100)]
mpc85xx: p1010: Fix Sophos RED 15w NAND partitions
This partially reverts 78d259e7d28d212425164fc64bf0b9d8669d6020.
That commit broke mounting the root fs on Sophos RED 15w due to
partition size mismatch, and changed the partition sequence, causing
the OpenWrt partition numbers to change from mtd3:kernel/mtd4:ubi to
mtd4:kernel/mtd5:ubi.
Andy Chiang [Tue, 9 Sep 2025 00:37:09 +0000 (07:37 +0700)]
ppp: add reqprefix norelease ac_mac
Use ppp and enable autoipv6, odhcp6c supports reqprefix and norelease to minimize the chance of IPv6 PD changes.[1]
PPPoE supports connecting to a specific AC/BRAS by using the pppoe-mac parameter.[2]
MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
2G: 80:3F:5D:xx:xx:x3
5G: 80:3F:5D:xx:xx:x4
* Installation with OEM WebUI:
Note: Make sure PC is connected on LAN1 port. The OEM firmware has an unknown root password and settings are kept after upgrading firmware. Therefore, a customized Openwrt firmware is needed to remove the root password on login, by adding `passwd -d root` to /etc/init.d/bootcount. The WebUI does a filename check so the customized firmware is named accordingly.
1. Download modified firmware file `WAVLINK_WN536AX6-A_M36AX6_V250320-WO-437baca-modified.bin` from https://github.com/ses1er/firmware-misc/tree/main/wavlink/wl-wn536ax6a
2. Log into WebUI on default IP: http://192.168.20.1
3. Browse to More (top menu) -> System -> Firmware Upgrade.
4. Under `Local Upgrade` section, check the device to be upgraded and upload downloaded modified firmware. Click `UPLOAD FILE`, then `APPLY`
5. Wait about 2 minutes (ignore progress bar), and browse to http://192.168.20.1. You should see LUCI login page. Username is root and no password.
6. Browse to `System -> Backup/Flash Firmware`, click on `Flash Image`, click `Browse` and locate `openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin` file.
7. Uncheck `Keep settings and retain the current configuration` and click `Continue`.
8. Router will now be set to IP 192.168.1.1 which is the Openwrt default.
* Installation with UART:
Note: Having UART connected while cold booting the device will result in a kernel panic when initializing wifi. I've found this workaround:
1. Power off the device and ensure UART is not connected to PC.
2. Power up the device, when lights come on, plug in UART.
3. Warm boots and soft restarts will not cause kernel panic for the duration of device being powered on. Repeat steps for subsequent cold boots.
1. Configure TFTP server with IP 192.168.1.66. Copy `openwrt-mediatek-filogic-wavlink_wl-wn536ax6a-initramfs.itb` to TFTP root.
2. Interrupt boot by pressing 0.
3. Run the following in Uboot console: `setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x46000000 openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-initramfs.itb; bootm`
4. Transfer `openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin` to device:
(`scp -O openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/`)
5. Run the following on device: `sysupgrade -n /tmp/openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin`
Installation:
The factory firmware is locked: you can only work with Cudy signed firmware.
Download a intermediate firmware signed by Cudy here:
https://www.cudy.com/blogs/faq/openwrt-software-download
After that, login to the router (192.168.10.254, password "admin") and install the intermediate firmware.
If you can reach LuCI or SSH now on the intermediate firmware, just use the sysupgrade image with the 'Keep settings' option turned off.
Special thanks to Daniel de Kock for starting the porting work at #16265.
Donghyun Ko [Fri, 1 Aug 2025 06:01:07 +0000 (15:01 +0900)]
mediatek: add support for ipTIME AX7800M-6E
Specification
-------------
- SoC : MediaTek MT7986AV quad-core ARM Cortex-A53 2GHz
- RAM : DDR4 512Mbytes, Nanya Technology NT5AD256M16E4
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976DAN, MediaTek MT7916AN, MediaTek MT7976AN
- 2.4GHz : b/g/n/ax, Multi User MIMO
- 5GHz : a/n/ac/ax, Multi User MIMO
- 6GHz : ax, Multi User MIMO
- Ethernet : 10/100/1000 Mbps x4, LAN (MediaTek MT7531AE)
10/100/1000/2500 Mbps x1, WAN (MaxLinear GPY211C0VC)
- UART : 1x4 pin header on PCB
- [J1] 3.3V, TX, RX, GND (115200, 8N1)
- Buttons : WPS, Reset
- Switches : Rfkill Slide Switch
- USB : 1x USB 3.0 (MediaTek MT7986AV peripheral)
- FAN : 1x Fan (off - slow - fast)
- LEDs : 1x Power (Blue)
1x CPU (Blue)
1x Wi-Fi 6GHz (Blue)
1x Wi-Fi 5GHz (Blue)
1x Wi-Fi 2.4GHz (Blue)
4x LAN activity (Blue)
1x WAN activity (Blue)
1x USB 3.0 (Blue)
- Power : 12VDC, 3.5A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+------------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+------------------------+
| WLAN 2.4G | 58:86:94:xx:xx:xx | label1 |
| WLAN 5G | 5A:86:94:xx:xx:xx | label2 with LA Bit set |
| WLAN 6G | 5A:86:94:xx:xx:xx | label1 with LA Bit set |
| WAN | 58:86:94:xx:xx:xx | label1 + 1 |
| LAN | 58:86:94:xx:xx:xx | label1 + 3 |
+-----------+-------------------+------------------------+
The WLAN 2.4G MAC address (label1) was found in 'Factory' partition, 0xA0004
The WLAN 5G MAC address (label2) was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software (ipTIME Firmware Wizard (11ac))
from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router (keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router (LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Note: The router will automatically reboot if no file is uploaded within
55 seconds.
Fan Control
------------
The fan speed is controlled by writing a value from 0 to 2 to the
`fan1_target` file.
```
cd /sys/devices/platform/gpio-fan/hwmon/hwmon2
echo '0' > fan1_target // off
echo '1' > fan1_target // slow
echo '2' > fan1_target // fast
```
Limitation: Enabling Wi-Fi 6E
----------
Wi-Fi 6E (6GHz) does not work out of the box on LuCI.
After installation, you need to configure a few settings in the `radio1`
and `default_radio1` sections of the `/etc/config/wireless`.
Once you have made these changes, you can enable and use Wi-Fi 6E.
In the `radio1` section, you need to add three common options:
- band: must be set to `6g`
- country: a valid country code for the 6GHz band
- channel: a preferrend scanning channel (PSC) for 6GHz
In the `default_radio1` section, you need to add the SSID and key:
- ssid: The public name of your Wi-Fi network
- key: The Wi-Fi password
- encryption: must be set to either `sae` for WPA3 or `owe` for OWE
(open network)
Example:
```
config wifi-device 'radio1'
...
option band '6g'
option country 'KR'
option channel '37'
...
Limitation: Maximum Transmit Power (Wi-Fi 6E)
----------
The maximum transmit power is currently broken. In the drop-down menu,
you can only choose between "driver default" and "255 dBm (2147493647
mW)". There is currently no workaround for the issue. Please leave the
maximum transmit power set to "driver default".
Michal Halva [Sat, 2 Aug 2025 18:46:14 +0000 (20:46 +0200)]
mediatek: filogic: add support for Cudy WR3000P v1
Hardware
--------
MediaTek MT7981 WiSoC
512MB DDR4 RAM
128MB SPI-NAND
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
4 LAN MediaTek MT7531 PHY
1 WAN RTL8221B-VB-CG 2.5Gbps PHY
UART: 115200 8N1 3.3V
USB2 Port
PoE on WAN Port
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Gotchas:
WAN LED does not light up (might require further DTS tweaks)
PoE on WAN port was not tested
This commit is heavily based on WR3000H one, I've just ported DTS differences
from the official image to get USB support and proper LED mapping.
Installation
------------
[Untested as I've received and used a transitional image from Cudy]
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000p.bin"
Liangbin Lian [Thu, 13 Nov 2025 07:17:57 +0000 (15:17 +0800)]
uboot-rockchip: add dedicated uboot for LinkEase EasePi R1
The generic-rk3568 does not reset the gmac phy, causing the kernel to
fail to initialize gmac during cold boot with the error message
"mdio_bus stmmac-1: MDIO device at address 1 is missing."
Adding a dedicated uboot for EasePi R1 to resolve this issue.
The EasePi R1's DTS hasn't been merged into the Linux release yet,
so it cannot be submitted to the upstream u-boot.
Liangbin Lian [Wed, 24 Sep 2025 12:08:13 +0000 (20:08 +0800)]
rockchip: Add support for RK3568 LinkEase EasePi R1
Specification:
- Rockchip RK3568
- 2GB/4GB LPDDR4 RAM
- 16GB on-board eMMC
- 1x M.2 key for 2280 NVMe (PCIe 3.0)
- 1x USB 3.0 Type-A
- 1x USB 2.0 Type-C (for USB flashing)
- 2x 1000 Base-T (native, RTL8211F)
- 2x 2500 Base-T (PCIe, RTL8125B)
- 1x HDMI 2.0 Output
- 12v DC Jack
- 1x Power key connected to PMIC
- 2x LEDs (one static power supplied, one GPIO controlled)
Debug Serial Port: 3.3V TTL, 3-pin 2.54mm pitch connector, 1500000 bauds,
'J7' on board with G/R/T (GND/RX/TX) pins marked
Installation - eMMC:
-Boot official firmware (OpenWRT based)
-Upload sysupgrade.img.gz to /tmp/firmware.bin (with scp or web page)
-Flash to eMMC: sysupgrade -n -p -F /tmp/firmware.bin
package: drop creating spurious tmp directory in feed directory
In implementing APK support it seems a a leftover was never removed that
creates an unused tmp directory in the package feed directory.
Drop it as it's not used anywhere. What is actually needed is the
creation of the $$(PDIR_$(1)) directory for the feed package directory
in the bin/packages directory.
This was a side effect of using INSTALL_DIR on $$(PDIR_$(1))/tmp that
indirectly creates the $$(PDIR_$(1)) parent directory.
Fixes: d788ab376f85 ("build: add APK package build capabilities") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f9802d70c633e5c502466e7b276613362967c8cb)
Lorenzo Bianconi [Sun, 16 Nov 2025 14:17:32 +0000 (15:17 +0100)]
mt76: Enable NPU support for Airoha AN7581 SoC
Airoha AN7581 SoC supports a Network Processor (NPU) to offload WiFi
traffic. Add the required bits to enable the support of it in the MT76
driver. This will be enabled by default if we are compiling for the
Airoha AN7581 SoC.
Felix Fietkau [Thu, 6 Nov 2025 11:36:14 +0000 (11:36 +0000)]
mt76: update to Git HEAD (2025-11-06)
0aece3089a3a wifi: mt76: mt7996: Remove useless check in mt7996_msdu_page_get_from_cache() 05b3d899ad24 wifi: mt76: Move Q_READ/Q_WRITE definitions in dma.h 85e6517b0ac5 wifi: mt76: Add mt76_dev pointer in mt76_queue struct. a3b6c67c97d2 wifi: mt76: Add the capability to set TX token start ID 141a81557070 wifi: mt76: Introduce the NPU generic layer 647d11bb17e0 wifi: mt76: mt7996: Add NPU offload support to MT7996 driver 8ff3b2bfc37f wifi: mt76: mt7996: fix typos in comments 0043147439b4 wifi: mt76: mt7925: refactor regulatory domain handling to regd.[ch] f0e8fe441489 wifi: mt76: mt7925: refactor CLC support check flow 588cc87bf6a2 wifi: mt76: mt7925: refactor regulatory notifier flow dac1d45fe94b wifi: mt76: mt7925: improve EHT capability control in regulatory flow c166c4a0e750 wifi: mt76: mt7925: add auto regdomain switch support d7b059bba166 wifi: mt76: mt7925: disable auto regd changes after user set 84f62a6beb99 wifi: mt76: mmio_*_copy fix byte order and alignment f5ae5b2e8116 Revert "wifi: mt76: mt792x: improve monitor interface handling" 8ae7e6dc1d3a wifi: mt76: adjust BSS conf pointer handling 1b438ebe0d06 wifi: mt76: mt7925: cqm rssi low/high event notify 7519fa4ce62c wifi: mt76: mt7996: fix max nss value when getting rx chainmask ea0580ad065f wifi: mt76: mt7996: no need to wait ACK event for SDO command 74112c2956fb wifi: mt76: mt7996: fix implicit beamforming support for mt7992 361d6bdac45d wifi: mt76: mt7996: support fixed rate for link station d99274cdc30c wifi: mt76: mt7996: fix several fields in mt7996_mcu_bss_basic_tlv() ad90a85b652b wifi: mt76: mt7996: fix teardown command for an MLD peer e9fe8bc03e41 wifi: mt76: mt7996: set link_valid field when initializing wcid 050394665502 wifi: mt76: mt7996: use correct link_id when filling TXD and TXP 5d223855552c wifi: mt76: mt7996: fix MLD group index assignment ab8361dbc421 wifi: mt76: mt7996: fix MLO set key and group key issues 7ce7ab881b3f wifi: mt76: mt7996: fix using wrong phy to start in mt7996_mac_restart() 1e0c23ff754b wifi: mt76: mt7996: fix EMI rings for RRO eb567bc7f9b6 wifi: mt76: mt7925: ensure the 6GHz A-MPDU density cap from the hardware.
Pawel Dembicki [Wed, 12 Nov 2025 21:33:24 +0000 (22:33 +0100)]
mac80211: mwl8k: inject DSSS Parameter Set element into beacons if missing
Some Marvell AP firmware used with mwl8k misbehaves when beacons do not
contain the DSSS Parameter Set (WLAN_EID_DS_PARAMS) with the current
channel. When hostapd/mac80211 omits this element (which is valid on
some bands), the firmware may report bogus RX channel information and AP
mode becomes unusable.
Backport the upstream fix that ensures beacons always carry the DSSS
Parameter Set for mwl8k: when setting the beacon, detect if the element
is missing and inject it after SSID and Supported Rates (per spec
ordering). This mirrors behaviour in newer Marvell drivers and restores
stable operation.
scripts/patch-kernel.sh: do not try to check files after patch
Since we are not using patch -b, *.orig files are only created when
there are conflicts, or never according to posix patch.
As such, it doesn't really make sense to always delete *.orig files
presuming they are patch backups, even if they are patch backups.
Doing so is both deleting potentially useful information for failed
patch applications and creating hard to diagnose bugs [1].
In a similar vein, checking for *.rej files does not add any value
since we're already checking the patch command's return code.
Ernestas Kulik [Wed, 12 Nov 2025 08:16:30 +0000 (10:16 +0200)]
scripts: feeds: Don’t hardcode IS_TTY
When building in environments that set IS_TTY, the feeds script does not
honor it and passes a hardcoded value to scan.mk, causing unwanted
control characters to appear in stdout.
This commit addresses the issue by checking IS_TTY and MAKE_TERMOUT
variables and uses their values if defined.
airoha: backport patch fixing out of order DMA for ethernet driver
Backport upstream patch fixing out of order DMA access for ethernet
driver. This is relevant in the context of QoS when packets doesn't
follow linear handling by QDMA HW.
Shiji Yang [Tue, 11 Nov 2025 21:03:43 +0000 (23:03 +0200)]
ipq806x: migrate wifi configuration device paths for 6.12 kernel
The device tree PCIe host node names have been changed in the new
6.12 kernel[1]. Hence we have to update the wifi device path to
make sure it can work properly.
This script is based on:
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
Backport the migration script that can also work backward, migrating
from 6.12 to 6.6. Like going from main/master to stable 24.10. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> Link: https://github.com/openwrt/openwrt/pull/20739 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Shiji Yang [Tue, 11 Nov 2025 21:02:22 +0000 (23:02 +0200)]
base-files: introduce a function to get kernel version number
A new function "get_linux_version()" to normalize and print the
kernel version as an integer. In some migration scripts, it is
useful for checking the Linux kernel version.
airona: an7583: fix typo for CONFIG_PHY_AIROHA_USB
KConfig flag have an extra whitespace for CONFIG_PHY_AIROHA_USB and
value is not ignored.
Drop the extra whitespace to correctly ignore the value on kernel
compilation.
Fixes: c5b12fc02ab1 ("airoha: Introduce support for Airoha AN7583 SoC") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit eedc7b3b79efed157636312e255b825d507a7182)
Enable USB node on eMMC RFB board and disable USB2 3.0 port to make the
3rd PCIe line correctly work.
This is needed to prevent the xHCI driver to mess with PCIe by
configuring the USB2 3.0 port. Port will still be detected but won't be
configureed by the driver and won't have PHY to configure for.
airoha: add pending patch for USB support on AN7581
Add pending patch for USB support on AN7581 SoC. This is also required
to make operational the 3rd PCIe line that use the USB2 Serdes for PCIe
operations.
(cherry picked from commit 7afc2da3fcc01a3932829ed4fb3ced6876b71846)
[ fix conflict errors, add missing Kconfig flag ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
airoha: an7581: add Aeonsemi AS21xxx PHY to RFB eMMC board
Airoha AN7581 eMMC RFB board mount 2 Aeonsemi AS21xxx PHY. One is
usually connected to GDM4 and the other is optionally connected to GDM2.
Add the relevant nodes to support the one connected to GDM4.
airoha: backport additional upstream patch for NPU support for AN7583
Backport additional patch required for NPU support of Airoha AN7583.
These are specific for the NPU module with some minor fixes and to adds
upport for loading the specific Airoha AN7583 NPU firmware.
airoha: an7583: drop bootloader artifacts entry and add default pkg
Fix the current image Makefile for Airoha AN7583 by dropping the
artifacts entry for bootloader and add default PKG for the PHY mounted
on the RFB boards.
The artifacts for the bootloader will be readded later once ATF-A
support will be pushed mainline.
airoha: an7583: add additional comments on EVB board
On the Airoha AN7583 EVB there are 2 Aeonsemi AS21xxx PHY but only the
one connected to Serdes Ethernet is usable as the other connected to
Serdes PON is not actually HW connected (as the serdes is connected to
the BOSA port)
Add missing syscon compatible for scuclk node.
Fix the unit-address of the scuclk node.
This fixes the pcs driver error:
airoha-pcs 1fa08000.pcs: probe with driver airoha-pcs failed with error -22
airoha-pcs 1fa09000.pcs: probe with driver airoha-pcs failed with error -22
Fixes: c3d70b1 ("airoha: en7581: Add support for external PHY") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Link: https://github.com/openwrt/openwrt/pull/20190 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a30daf8a0b3f3c25a46320f5e7932d01c63301ef)
Chukun Pan [Tue, 9 Sep 2025 15:06:02 +0000 (23:06 +0800)]
airoha: set default DEVICE_DTS/DEVICE_DTS_DIR
All devices under airoha use dts directory under the target,
so update the default DEVICE_DTS_DIR. Also set the default
DEVICE_DTS based on the SoC name for non-dev boards.
Introduce initial support for Airoha AN7583 SoC and add all the required
patch for basic functionality of the SoC.
Airoha AN7583 is based on Airoha EN7581 SoC with some major changes on
the PHY handling and Serdes. It can be see as a lower spec of EN7581
with modern and simplified implementations.
All the patch are sent upstream and are pending revision. Support for
PCIe and USB will come later as soon as DT structure is accepted
upstream.
(cherry picked from commit c5b12fc02ab133be1c18722e9b3c5b93e7772925)
[ fix conflict errors, add MDIO_AIROHA config ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This add a pending version of the Airoha PCS driver to add support for
External PHY. The Airoha PCS driver will receive some minor modification
once we the PCS subsystem will be defined upstream.
Add all the required node for GDM2 and GDM4 and enable the PCS config.
Fixes warning:
/linux/arch/arm64/boot/dts/airoha/en7581-gemtek-w1700k.dtb: i2c1@1fbf8100 (mediatek,mt7621-i2c): status: 'oneOf' conditional failed, one must be fixed:
['disable'] is not of type 'object'
'disable' is not one of ['okay', 'disabled', 'reserved', 'fail', 'fail-needs-probe']
from schema $id: http://devicetree.org/schemas/dt-core.yaml#
The baud rate control on Airoha does not function properly. This
patch enables the inactive code responsible for this. The UART2
baud rate is correct. HSUART3 operates at twice the requested
baud rate. The same problem exists in the current code, so this
doesn't introduce any regression. Support for baud rates higher
than 460800 is still required. This will be added in the future.
Tested on Gemtek W1700k. UART2 and HSUART3 are working fine.
airoha: backport upstream fixes for pinctrl PHY LED and MDIO
Backport fixes for Airoha pinctrl driver for PHY LED and MDIO bus. This
fix a copy-paste error for PHY LED and a misconfiguration for MT7530
embedded Switch MDIO bus GPIO pin to permit usage of external PHYs.
airoha: replace thermal patch with upstream version
Replace thermal patch with upstream version. The thermal maintainer
reported that the sysfs entry are considered deprecated and that slope
and offset should be handled internally to the driver.
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
3. Download the sysupgrade firmware at openwrt.bin.
4. The firmware size should be 7995392 bytes. Fix the size of your firmware putting zeros to the end, with:
Shiji Yang [Sat, 24 May 2025 08:32:26 +0000 (16:32 +0800)]
ramips: dts: increase maximum MMC clock frequency
The High-Speed SD mode stability issue should have been fixed.
Increase the MMC max-frequency to improve the IO speed. We can
still use the sysfs to limit the clock frequency, e.g.
Shiji Yang [Sat, 24 May 2025 08:31:07 +0000 (16:31 +0800)]
ramips: mtk-mmc: fix data timeout value
The MT7628 programing guide shows that the correct DTOC unit is 1048576 clocks instead of 65536 clocks. This value is also used
by linux upstream mtk-sd driver. Correct the DTOC register and
also round up its value.
Shiji Yang [Mon, 19 May 2025 23:50:56 +0000 (07:50 +0800)]
ramips: dts: adjust the power regulators of MMC controller
- Fix MMC bus IO voltage. The GPIO voltage of mt762x series SoCs
is fixed 3.3V. There are no visible registers that can control
the voltage level. Also add "no-1-8-v" property to indicate that
MMC controller doesn't support 1.8V IO.
- Drop useless property "enable-active-high". These dummy fixed
voltage regulators are not controlled by the GPIO. We don't need
to set the GPIO polarity.
Andreas Gnau [Fri, 3 Oct 2025 08:59:42 +0000 (10:59 +0200)]
tools/ccache: same behaviour for local and CI builds
If the environment variable `CI` is set, ccache will enable the CMake
option CCACHE_DEV_MODE by default. This leads to differing behaviour
between local and CI builds which takes quite some time to debug. 🤯
Achieve consistent behaviour between local builds and CI builds by
setting CCACHE_DEV_MODE. Set it to OFF, because CCACHE_DEV_MODE amongst
other settings like linker choice, enables -Werror, which will lead to
potential compilation failures when the host compiler is updated. Using
-Werror for host utils is not desirable, because the compiler version
used is not controlled by the OpenWrt build system and host utils should
compile successfully on an as wide range of host OSes as possible.
Robert Marko [Wed, 23 Apr 2025 12:18:48 +0000 (14:18 +0200)]
mold: dont allow on MacOS
Mold does not really work on MacOS, when attempting to use it for example
for ubus:
mold: get_self_path is not supportedcollect2: error: ld returned 1 exit status
Which was introduced by [1] so it seems that MacOS is not supported, so
lets make it non selectable when MacOS is the host.
projects / thirdparty / openwrt.git / log
