A lot of soc_info usage has been reorganized. Nevertheless there
are some consumers left. A very critical one is the dsa/qos coding.
It makes use of the cpu_port in this shared structure. This is
totally broken as that info is never properly initialized. Fill
the cpu_port according to the identified hardware.
Remark: Looking at the prom.c history soc_info.cpu_port was never
setup since the beginning of time. So no "fixes" tag here.
realtek: RTL930x: setup highmem registers during init
For some reason the highmem configuration of RTL930x
devices was totally missed until now. Take over the
setup from the SDK. This will avoid boot stalls on
switches with more than 256 MB RAM when switching
over to kernel 6.18.
realtek: determine memory size during initialization
For proper highmem initialization on RTL930x the size of the
installed memory is needed during early bootup. Enhance the
soc_info structure and fill the data from the registers.
While we are here remove the obsolete compatible variable from
the soc_info structure.
Adapt boot message to show the memory size.
old: SoC Type: Realtek RTL9301 rev B (6487)
new: Realtek RTL9301 rev B (6487) SoC with 512 MB
There is mix of variable naming in prom.c. Use a fixed
prefix of "rtl_" for all static variables. Additionally
remove the prefix from rtl83xx_set_system_type as it is
a generic function for all SoC types.
George Sapkin [Thu, 25 Dec 2025 15:16:18 +0000 (17:16 +0200)]
ca-certificates: provide a virtual package
Switch ca-certs provides to use the new virtual provides semantic that
enables ca-bundle and ca-certificates to be installed side-by-side.
Provide the new format virtual ca-certificates-any in ca-bundle.
Fixes: https://github.com/openwrt/openwrt/issues/21257 Signed-off-by: George Sapkin <george@sapk.in> Link: https://github.com/openwrt/openwrt/pull/21288 Signed-off-by: Robert Marko <robimarko@gmail.com>
George Sapkin [Sun, 28 Dec 2025 15:22:41 +0000 (17:22 +0200)]
build: provide virtual self in kmods
Add an implicit self-provide to kmods. apk can't handle self provides,
be it versioned or virtual, so opt for a prefix and a suffix instead.
Package name without a prefix/suffix is too generic and might conflict
with other packages, e.g. wireguard. This allows several variants to
provide the same virtual package without adding extra provides to the
default one, e.g. r8169 implicitly provides kmod-r8169-any and is marked
as default, so r8125 can explicitly provide @kmod-r8169-any as well.
George Sapkin [Thu, 25 Dec 2025 13:32:29 +0000 (15:32 +0200)]
build: add support for virtual provides
Allow defining virtual provides using the PROVIDES field by prefixing
them with @, e.g.:
PROVIDES:=@ca-certs
Virtual provides don't own the provided name and multiple packages with
the same virtual provides can be installed side-by-side. Packages must
still take care not to override each other's files.
Add an implicit self-provide to packages. apk can't handle self
provides, be it versioned or virtual, so opt for a suffix instead. This
allows several variants to provide the same virtual package without
adding extra provides to the default one, e.g. wget implicitly provides
wget-any and is marked as default, so wget-ssl can explicitly provide
@wget-any as well.
Filter out virtual provides when generating metadata.
Filter out virtual provides prefix and self provide where appropriate.
Co-authored-by: Goetz Goerisch <ggoerisch@gmail.com> Signed-off-by: John Audia <therealgraysky@proton.me> Link: https://github.com/openwrt/openwrt/pull/21329 Signed-off-by: Robert Marko <robimarko@gmail.com>
Eric Fahlgren [Mon, 3 Nov 2025 20:34:37 +0000 (12:34 -0800)]
mediatek: filogic: fix supported_devices list for gl-mt2500
The SUPPORTED_DEVICES sets for both Maxlinear (v1) and Airoha (v2)
devices were identical, so sysupgrade was unable to detect when an
incorrect image was being installed. This caused "soft bricking" of
devices when a v1 image was installed on a v2 device, and vice versa.
Fix this by making the supported_devices distinct for each device
version, by renaming the devices with a version-specific name.
This is reflected in the file name and the image metadata.
Fil Dunsky [Fri, 12 Dec 2025 15:51:39 +0000 (18:51 +0300)]
mediatek: add ubootmod layout for Cudy WBR3000UAX v1
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
If you are at factory firmware, please refer
to [PR](https://github.com/openwrt/openwrt/pull/21141)
to boot into OpenWrt first.
1. Log in to the device and backup all the partitions,
especially unique `Factory` and `bdata` partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing:
```bash
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
```
3. Write new OpenWrt (U-Boot Layout) `BL2` and `FIP`:
```bash
mtd write openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-bl31-uboot.fip FIP
```
4. Set static IP on your PC: `192.168.1.254`, gateway `192.168.1.1`
5. Serve openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean `/dev/mtd5` ubi partition to utilize maximum of free space & create ubootenvs:
```bash
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
4. Perform sysupgrade.
Based on a factory layout with only 64mb partition for easier transition from factory to OpenWrt for users if the "intermediate" RSA signed firmware will be provided by Cudy.
**Installation**
The installation must be done via UART & TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware and dts to make installation easier, but since this router is OEM special WB order for local RU market there is a possibility they will not provide it.
**Install using UART & TFTP**
1. Connect to UART.
2. Since the factory BL is locked and the boot process can not be stopped, you have to use mtkuartboot, hold reset, engage the power, boot into your payloaded bl2 & fip.
3. Connect to LAN and set your IP to 192.168.1.254.
4. Configure a TFTP server to serve openwrt-mediatek-filogic-cudy_wbr3000uax-v1-initramfs-kernel.bin file.
5. Run these steps in u-boot using the name of your file:
Since there are many similar devices from Cudy (TR3000 / WR3000E / WR3000P / WR3000S / WBR3000UAX) this will allow to create OpenWrt U-Boot layout for all of them using same DDR3 target.
Hauke Mehrtens [Sun, 28 Dec 2025 22:03:32 +0000 (23:03 +0100)]
wifi-scripts: use OWE + country for 6GHz
Wifi on the 6GHz band does not support open networks, configure owe by
default. 6GHz wifi also needs a country code, configure a broken country
code '00' by default to hint the user to change it.
Hal Martin [Sun, 28 Dec 2025 13:43:17 +0000 (14:43 +0100)]
ipq40xx: add support for Cisco Meraki MR20
This commit adds support for the Cisco Meraki MR20/Go GR10.
The Meraki MR20 is a Cisco 802.11ac/WiFi 5 AP with 1 Ethernet port.
It can be powered by a 12V DC barrel jack (5.5x2.5mm, center positive)
or via 802.3af POE.
The Meraki Go GR10 (codename: Maggot) is identical to the MR20
(codename: Grub), so this document will refer to both devices as the MR20.
This device ships with secure boot, and cannot be flashed without
external programmers (TSOP48 NAND and I2C EEEPROM)!
Disassembly:
Remove the four rubber feet on the rear of the AP and the four
Torx T8 screws under the feet.
Using a guitar pick or similar plastic tool, insert it on the side
along the seam around the edge. Push in gently while gently lifting
the front of the housing to release the plastic retention clips.
There are 15 clips in total.
Once you have removed the plastic front (shown above already removed
so you know where the clips are), remove the 4 Philips screws holding
down the two metal WiFi antennas.
Lift the PCB gently while pushing the Ethernet port into the housing
to release it. The PCB should come free from the metal heat spreader.
The TSOP48 NAND flash (U9, Macronix/MXIC MX30LF1G18AC) is located on
the opposite side of the PCB.
To flash, you need to desolder the TSOP48 or use a 360 clip.
You also need to reprogram the I2C EEPROM (U20, Atmel 24c64).
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/mr20_gr10
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Decompress `ubi.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `ubi` portion of NAND from
`0xc60000`-`0x8400000` (length `0x77a0000`). Offsets here include OOB data.
* Dump your original EEPROM. Change the byte at offset `0x49` to `0x1e`
(originally `0x2c` or `0x25`). Remember to re-write the EEPROM with the
modified data.
* This can be done on Linux via the following command:
`printf "\x1e" | dd of=/tmp/eeprom.bin bs=1 seek=$((0x49)) conv=notrunc`
**Note**: the device will not boot if you modify the board major number and
have not yet overwritten the `ubi` and `u-boot` regions of NAND.
* Resolder the NAND after overwriting the `u-boot` and `ubi` regions.
OpenWrt Installation:
* After flashing NAND and EEPROM with external programmers. Plug in an
Ethernet cable and power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_mr20-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, created the `ART` ubivol with
the WiFi radio calibration from the mtd partition:
```
cat /dev/mtd10 > /tmp/ART.bin
ubiupdatevol /dev/ubi0_1 /tmp/ART.bin
```
* `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr20-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr20-squashfs-sysupgrade.bin"
```
Hal Martin [Mon, 22 Dec 2025 09:48:46 +0000 (10:48 +0100)]
ipq40xx/meraki: refactor common device tree
qcom-ipq4029-insect-common.dtsi was common to the MR33 and MR74, but was no
longer common with the other supported Meraki devices. I have refactored
insect-common and wired-qca-common into qcom-ipq4029-meraki-common.dtsi
which contains the actual common components (e.g. NAND partitions, ART nvmem).
Individual devices reference qcom-ipq4029-meraki-insect.dtsi
plus their own individual configuration.
The SerDes mode setting at the end of rtpcs_931x_setup_serdes is
currently broken although it is mostly similar to what the SDK does [1].
It prevents several modes from being set, especially fiber modes. This
seems to be one (if not the only) issue for currently missing SFP
support.
Add a small helper function which takes cares of setting the mode, to
keep the still valid different procedure when using XSGMII mode. Only
this helper is called in rtpcs_931x_setup_serdes to keep it clean there.
As a functional change, call mode application in every case, not just
for SGMII, QSGMII and USXGMII. We can assume the SDK is misleading in
this case, either accidentially or on purpose. This makes SFP modules
work in theory. In practice, there still seem to be device-specific
issues which need to be fixed later. These issues may include no link
detection or link flapping.
The SDK and our code for finally applying the hardware mode are quite
confusing. There are two different "places" where a mode can be set,
in a SerDes register and in a global SerDes mode register. Neither the
SDK nor any of the datasheet/documentation serve any explanation for
that. The functions are just named "fiber_mode_set" and "mii_mode_set"
which is basically as useless as it can be to understand it.
Try to get rid off this confusion by naming the functions
'sds_set_mac_mode' and 'sds_set_ip_mode' to make clear where the mode
is set. While at it, also clarify the naming of 'config_mode' by
renaming it to 'config_hw_mode'.
The naming is based on the following assumption:
> Realtek uses an SerDes IP core design (probably from another vendor)
> in their switch. This supports a variety of modes and must be
> configured properly for each mode. Usually, changing the mode in the
> MAC's registers triggers a proper configuration of the SerDes IP block
> in the background.
> However, for some modes this seems to be incomplete, at least missing
> important parts so it doesn't work on its own in the end. In this
> case, the SerDes IP block needs to be configured manually with the
> missing bits to make it work.
There are several places in the SDK that support this assumption, both
for RTL931X and RTL930X (as they are somewhat similar), e.g. [1].
Improve the current mode setting functions to address a few issues:
- add missing mode from SDK reference (instead of using the
corresponding value as a default value)
- use and return error values
- give internal variable a more meaningful name
- consistently use lowercase letters in hex values
Jonas Jelonek [Sat, 20 Dec 2025 21:09:52 +0000 (21:09 +0000)]
realtek: pcs: rtl931x: merge and drop unused helper
Merge the unused helper 'rtpcs_931x_sds_fiber_disable' into Fiber mode
setting, and drop the helper itself. As with the MII helper in a
previous commit, functionality is basically the same just with a value
for OFF mode. If functionality is required later, Fiber mode setting can
be used with the OFF mode instead of carrying the unused helper until
it's used.
Jonas Jelonek [Sat, 20 Dec 2025 20:40:12 +0000 (20:40 +0000)]
realtek: pcs: rtl931x: merge helper into mode setting
Merge the 'rtpcs_931x_sds_disable' helper into the MII mode setting and
use that instead. The helper was essentially doing same just with a
value for OFF state.
Moreover, the name of the helper was confusing. It implied it disables
the whole SerDes. However, this is used in Fiber mode setting and thus,
cannot completely disable the SerDes.
Jonas Jelonek [Sat, 20 Dec 2025 21:42:34 +0000 (21:42 +0000)]
realtek: pcs: rtl931x: fix MII mode setting
The function 'rtpcs_931x_sds_mii_mode_set' does not correctly write the
register. It just write a plain value at the determined register
address. While this works for SerDes with (id mod 4 == 0), it doesn't
for the other SerDes.
Fix that by using a corresponding shift and writing only some bits
instead of the whole register.
While at it, drop an unneeded blank line, add comment to explain a bit
that is set and use the BIT(..) helper for that instead of manual shift.
Jonas Jelonek [Sat, 20 Dec 2025 18:36:56 +0000 (18:36 +0000)]
realtek: pcs: rtl931x: fix clearing symbol errors
Fix the implementation to clear symbol errors. Up to now, it was barely
functional because important modes weren't handled. Add another function
(which is needed in the future anyway) and pick to missing bits from
that function into the symbol clearing function to handle the modes
1000Base-X and 10GBaseR too. All that is based on [1].
While at it, rename the function to adhere to a common naming scheme and
fix some minor style issues.
realtek: mdio: move cpu_port to configuration structure
Relocate the cpu port definition over to the new configuration
structure. There are several family specific places where the
driver checks port ranges. These are a wild mix of arbitrary
values (64) or constant defines. Remove them as the the central
read/write functions already have a proper check with -ENODEV
bail out in place.
With the cleanup drop the port defines as there is only one
consumer (config structure) left.
realtek: mdio: add per family configuration structure
The mdio driver already has a family specific compatible that
is used in the dts to denote the device type. Nevertheless it
is not evaluated. The driver determines the family on its own
in rtmdio_get_family().
Break up this dependency by providing a configuration structure
that can be automatically assigned by device_get_match_data().
For now only move the rawpage variable over there.
realtek: ethernet/dsa: Reduce mach include dependency
The ethernet and dsa drivers still rely on several defines from
the central mach include. Move important defines over to the
driver specific includes as a first decoupling step.
Zhenyu Qi [Sat, 13 Dec 2025 21:04:51 +0000 (14:04 -0700)]
qualcommax: ipq60xx: enable dual-boot for 360v6
Add dual-partition upgrade support for Qihoo 360v6 using the generic
bootconfig.sh library. This enables safe system upgrades with automatic
failover capability.
The device uses Qualcomm's bootconfig structure to control A/B partition
switching. The bootloader dynamically maps physical NAND partitions to
logical MTD devices based on the bootconfig, ensuring firmware always
writes to the inactive partition.
Implementation details:
- Use bootconfig.sh library (copied from ipq50xx) for bootconfig operations
- Operate on 'rootfs' partition by name instead of hardcoded offset
- Add magic header validation for safety
- Remove OEM UBI volumes (wifi_fw and ubi_rootfs) before sysupgrade
- Toggle bootconfig before removing OEM volumes
Hardware details:
- SoC: Qualcomm IPQ6000
- Flash: NAND with dual rootfs partitions (mtd16/mtd17)
- Bootconfig: controls slot selection via partition name lookup
Installation:
Standard sysupgrade process. After upgrade, the system will boot
from the new partition while preserving the old system as backup.
The OEM volume cleanup is necessary because these volumes are created
by the stock firmware and are not automatically cleaned by the standard
nand_upgrade_prepare_ubi() function, which only removes volumes named
'kernel', 'rootfs', and 'rootfs_data'. Without this cleanup, the remaining
OEM volumes consume available space, causing the creation of rootfs_data
to fail during sysupgrade.
Tested on Qihoo 360v6 running stock firmware and OpenWrt.
Nick Hainke [Sat, 27 Dec 2025 12:43:47 +0000 (13:43 +0100)]
wifi-scripts: fix race in wireless interface creation
When wdev interfaces and hostapd interfaces are mixed, race conditions
can occur. Sometimes all interfaces are started correctly, sometimes only
the wdev interface and some of the hostapd interfaces, and sometimes only
the wdev interface.
Fix this by creating the wdev interfaces first, before processing
wpa_supplicant or hostapd interfaces.
RTL930x devices have highmem starting address at 0x20000000.
The Linksys LGS328C highmem definition is wrongly shared with
the larger LGS352C RTL931x model and starts at 0x90000000.
Fix it by splitting the definition.
Fixes: 853d73f ("realtek: add support for Linksys LGS328C") Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> Link: https://github.com/openwrt/openwrt/pull/21262 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Nick Hainke [Fri, 26 Dec 2025 17:35:01 +0000 (18:35 +0100)]
wifi-scripts: fix mcast_rate type (number, not array)
The multicast rate (mcast_rate) is defined as a single numeric value,
not an array. The ucode scripts already expect a single number, and
the OpenWrt documentation specifies this option as an integer [0].
Adjust the wireless schema accordingly. This also fixes the wdev.uc
call path for the iw fallback mesh setup.
Nick Hainke [Thu, 25 Dec 2025 17:41:10 +0000 (18:41 +0100)]
wifi-scripts: fix wdev fallback for mesh interfaces
The previous wdev.uc invocation failed for mesh interfaces.
Rewrite it as a loop so the mesh interface is created correctly
when no wpa_supplicant mesh support is installed.
Yuhei Amemiya [Sun, 21 Dec 2025 07:03:20 +0000 (15:03 +0800)]
mediatek: add support for Elecom WRC-G01
Hardware is identical to WRC-X3200GST3.
- SoC: MediaTek MT7622
- RAM: 512MB
- Flash: 128MB SPI-NAND
The -W suffix in the retail name (WRC-G01-W) denotes the casing color
and is omitted from the model name in the OpenWrt configuration to
maintain consistency with other Elecom devices.
Nick Hainke [Thu, 25 Dec 2025 19:32:28 +0000 (20:32 +0100)]
wifi-scripts: ucode: fix wpa_supplicant mesh
Mesh interfaces may not define an encryption setting. This results in
a ucode runtime error when parse_encryption() is called:
Reference error: left-hand side expression is null
In parse_encryption(), file /usr/share/ucode/wifi/iface.uc, line 20, byte 32:
called from function setup_sta (/usr/share/ucode/wifi/supplicant.uc:59:31)
called from function generate (/usr/share/ucode/wifi/supplicant.uc:243:41)
called from function setup (./mac80211.sh:254:61)
called from anonymous function (./mac80211.sh:342:14)
` config.auth_type = encryption[0] ?? 'none';`
Near here ------------------------^
Interrupt vector for reo2host-status is wrongly assigned.
Status interrupts weren't received and a workaround was applied to
mac80211 to periodically poll the reo status ring. Therefore, the
workaround can be removed with the proper hardware interrupt line
assigned.
Flash instructions:
************************************************************************
NOTE: serial access is required! Although the web UI allows you to
install the Openwrt image, secure boot is enabled which will prevent
booting an unsigned image. The boot sequence must be adjusted in U-boot
to allow booting unsigned images.
************************************************************************
1. On OEM firmware, login to the web UI (typically @ http://192.168.1.1)
and click 'CA' in the bottom right corner.
Then click -> Connectivity -> Manual Upgrade.
Alternatively, browse to
http://<router IP>/fwupdate.html.
Upload openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-factory.ubi.
Continue with step 5.
2. Installation on alternate partition using serial connection from OEM
firmware (default login: root, password: admin):
flash_erase /dev/mtd19 0 0
nandwrite -p /dev/mtd19 openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-factory.ubi
reboot
Continue with step 5.
3. Installation using serial connection from initramfs
setup tftp server listening on IP in 192.168.1.0/24 (other than the
router IP 192.168.1.1). In U-boot, load the initramfs image to memory:
tftp $loadaddr <your IP>:openwrt-qualcommax-ipq50xx-linksys_mx6200-initramfs-uImage.itb
boot the image using command:
bootm $loadaddr
when fully booted, scp the sysupgrade image to your router IP (default:
192.168.1.1):
scp -O <path>/openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-sysypgrade.bin root@192.168.1.1:/tmp/
use sysupgrade to flash the image to nand:
sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-sysupgrade.bin
Continue with step 5.
4. Optionally install on alternate partition. From Openwrt:
mtd -r -e rootfs_1 -n write openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-factory.ubi rootfs_1
Continue with step 5.
5. Setup U-boot for ability to dual boot signed (stock) and non-signed
(Openwrt) images with auto-detection.
From U-boot, run (be aware: copy line by line):
setenv setnandbootargs 'setenv bootargs init=/sbin/init ubi.mtd=rootfs rootfstype=squashfs rootwait'
setenv nandinitcmd 'setenv mtdids nand0=nand0; run setrootfscmd; ubi part rootfs 2048'
setenv setrootfscmd 'if test $boot_part = 1; then setenv mtdparts mtdparts=nand0:0x${imgsize}@0x${prikern}(rootfs); else setenv mtdparts mtdparts=nand0:0x${imgsize}@0x${altkern}(rootfs); fi'
setenv readhdr1cmd 'ubi read $loadaddr kernel 0x40; setexpr IMGOFF $loadaddr + 0x10; setexpr CODEOFF $loadaddr + 0x14; setexpr SIGOFF $loadaddr + 0x1c; setexpr CERTOFF $loadaddr + 0x24'
setenv readhdr2cmd 'setexpr.l HDR *$loadaddr; setexpr.l IMGSZ *$IMGOFF; setexpr.l CODESZ *$CODEOFF; setexpr.l SIGSZ *$SIGOFF; setexpr.l CERTSZ *$CERTOFF; setexpr TSIZE $CODESZ + $SIGSZ; setexpr TSIZE $TSIZE + $CERTSZ'
setenv testmbncmd 'if test $HDR -ne edfe0dd0 -a $IMGSZ -eq $TSIZE; then bootipq; else ubi read $loadaddr kernel $kernsize; run setnandbootargs; bootm $loadaddr; fi'
setenv bootcmd2 'if test $auto_recovery = no; then bootipq; else run nandinitcmd; run readhdr1cmd; run readhdr2cmd; run testmbncmd; fi'
setenv bootcmd 'run bootcmd2'
saveenv
6. Back to the OEM firmware.
Download firmware from OEM website:
MX6200: https://support.linksys.com/kb/article/408-en/
From serial/SSH, in Openwrt, flash OEM firmware to alternate partition:
mtd -r -e rootfs_1 -n write FW_MX6200_1.0.11.216041_prod.signed.img rootfs_1
Switching active partition:
1. From U-boot, executive the following to switch to partition 1:
setenv boot_part 1
for partition 2:
setenv boot_part 2
2. From Openwrt:
fw_printenv boot_part
In case it's 1:
fw_setenv boot_part 2
. /lib/upgrade/platform.sh
linksys_bootconfig_set_primaryboot "0:bootconfig" 1
linksys_bootconfig_set_primaryboot "0:bootconfig1" 1
In case it's 2:
fw_setenv boot_part 1
. /lib/upgrade/platform.sh
linksys_bootconfig_set_primaryboot "0:bootconfig" 0
linksys_bootconfig_set_primaryboot "0:bootconfig1" 0
and
reboot
Add support for upgrades on dual firmware Linksys devices with the
partition table stored in SMEM and that store both the kernel and rootfs
in a single partition. Switching the active boot partition requires
updating the partition info table in SMEM in addition to setting
the active boot partition in a U-boot variable as U-boot will keep them
in sync upon reboot if they're not.
U-boot always sets the name of the active partition to rootfs and that
of the inactive partition to rootfs_1 in SMEM. when Linux loads the
partition table from SMEM it will load the right partition based on the
offset set in the SMEM partition table. For upgrades, flashing to the
alternate partition will always be to rootfs_1, while flashing the
current partition will be on rootfs.
qualcommax: ipq50xx: functions for bootconfig partition
The BOOTCONFIG partition is used by Qualcomm's boot chain to store
metadata about the device's startup configuration. It contains info such
as versioning, configuration flags, primary boot partition, and more.
Newer devices with dual boot partitions not only store the active boot
partition in a U-boot variable but also in partition info in the
BOOTCONFIG partition. As such, add library functions to set and toggle
the active boot partition.
qualcommax: ipq50xx: move bootargs to Linksys board files
Move setting kernel bootargs from the base template down to the
respective Linksys board files. This allows for having devices which
require different bootargs use the base template device tree file.
qualcommax: ipq50xx: load Linksys partition tables from SMEM
The partition table on Linksys devices with a Qualcomm AX IPQ SoC is
stored in SMEM. As such, load partition table from SMEM rather than
statically defining them in their respective device trees. This helps
generalize the base template and requires less maintenance.
qualcommax: ipq50xx: remove ipq5018 and qcn6122 wifi m3 fw
The current ath11k driver does not support loading m3 firmware for
IPQ5018 and QCN6122 wifi. Although m3 firmware entries are specified
in Q6 WCSS nodes, the driver actually skips loading them. Editing the
driver to force loading m3 results in Q6 crashes and non-functioning
wifi. As such, remove m3 firmware entries for all boards until there's
proper support in the ath11k driver.
George Sapkin [Wed, 24 Dec 2025 02:32:01 +0000 (04:32 +0200)]
toolchain: fix libgcc ABI for libc
libc depends on knowing libgcc's ABI, so it needs to be evaluated first.
Otherwise libc will depend on an ABI-less libgcc causing the rest of the
toolchain to fail.
Building package index...
ERROR: unable to select packages:
libgcc (virtual):
note: please select one of the 'provided by'
packages explicitly
provided by: libgcc1
required by: world[libgcc]
Jonas Jelonek [Mon, 15 Dec 2025 19:41:16 +0000 (19:41 +0000)]
realtek: pcs: rtl931x: add helper for SerDes power up/down
Add a dedicated helper 'rtpcs_931x_sds_power' to power down/up a SerDes.
Up to now, plain register writes to the corresponding register were used
in several places and with slightly different syntax. Use the helper to
replace the existing boilerplate code for powering on/off SerDes.
Jonas Jelonek [Mon, 15 Dec 2025 18:45:54 +0000 (18:45 +0000)]
realtek: pcs: rtl931x: reorder modes in mode configuration
Reorder the modes within the switch statement in
rtpcs_931x_sds_config_mode to have a proper and non-confusing order.
Have fiber modes first and MII modes after, and sort all modes in
ascending speed/capabilities order.
Jonas Jelonek [Mon, 15 Dec 2025 17:37:01 +0000 (17:37 +0000)]
realtek: pcs: rtl931x: map interface mode to hardware mode
The PCS driver is intended to use a dedicated hardware mode in the
future because the hardware capabilities and modes of the SerDes do not
align with the PHY_INTERFACE_MODE_* modes.
For the beginning, use the previously introduced generic mode mapping
in the SerDes setup and assign the determined hardware mode to the
corresponding field of a SerDes instance. This allows parallel usage of
both mode representations for the time being, until the phy_interface_t
modes can be dropped from internal functions completely.
Jonas Jelonek [Sun, 14 Dec 2025 11:34:34 +0000 (11:34 +0000)]
realtek: pcs: rtl931x: move SerDes config out of setup
Slim the rtpcs_931x_setup_serdes entrypoint by moving the SerDes
configuration sequences for the different SerDes modes into a dedicated
function called rtpcs_931x_sds_config_mode. They form a logical block
similar to what the SDK does and can be taken out to follow the
'divide & conquer' principle.
Jonas Jelonek [Tue, 11 Nov 2025 09:55:42 +0000 (09:55 +0000)]
realtek: pcs: rtl931x: don't return error on USXGMII setup
Configuring USXGMII on RTL931X was disable because it is not setup
properly right now. Affected devices need to rely on U-boot setup for
now. However, it is not the proper way to return an error in case we
just want to skip USXGMII configuration. Thus, just return 0 in that
case indicating it is properly configured.
Jonas Jelonek [Fri, 19 Dec 2025 10:11:06 +0000 (10:11 +0000)]
realtek: pcs: add mapping for SerDes hardware mode
Add a generic mapper for mapping the PHY_INTERFACE_MODE_* modes to the
SerDes hardware modes RTPCS_SDS_MODE_*. This is to be used by all
subtargets step-by-step and avoids having subtarget-specific code for
that simple mapping.
Jonas Jelonek [Wed, 17 Dec 2025 21:33:17 +0000 (21:33 +0000)]
realtek: pcs: rename SerDes mode field
Rename the mode field in rtpcs_serdes from 'mode' to 'hw_mode' to make
clear what it actually is, to avoid confusion with the phy_interface_t
'mode' usually passed to functions.
Shiji Yang [Fri, 12 Dec 2025 13:39:40 +0000 (21:39 +0800)]
kernel: rtl836x: convert to gpiod API
This is the recommended way for the OF based platform.
Tested-on TP-Link TL-WR2543N with RTL8367 switch:
```
root@OpenWrt:~# dmesg |grep -i rtl
[ 7.941126] rtl8367 rtl8367: cannot find mdio node phandle
[ 7.947562] rtl8367 rtl8367: RTL8367R ver. 0 chip found
[ 9.056830] rtl8367 rtl8367: cpu_port:9, assigned to extif0
root@OpenWrt:~# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 512-529, parent: platform/18040000.gpio, 18040000.gpio:
gpio-512 ( |lime:status ) out lo ACTIVE LOW
gpio-513 ( |rtl836x-sda ) in hi
gpio-518 ( |rtl836x-sck ) in lo
gpio-520 ( |lime:usb ) out hi ACTIVE LOW
gpio-523 ( |reset ) in hi IRQ ACTIVE LOW
gpio-524 ( |wps ) in hi IRQ ACTIVE LOW
```
realtek: ethernet: switch to new family_id location
family_id is now part of the register set and automatically assigned
during initialization. Make use of it. This is basically a conversion
from priv->family_id to priv->r->family_id.
While we are here convert some hard coded family ids to their proper
defines.
realtek: ethernet: provide soc family in register config
The ethernet driver currently determines the family from the soc_info
structure. To avoid the dependency add the family to the local register
structure.
realtek: ethernet: relocate ethernet below switchcore in DTS
The ethernet driver uses registers in the switchcore range.
Rearrange the DTS nodes accordingly. This allows to make use
of regmap with syscon_node_to_regmap(np->parent) later.
The Realtek Otto ethernet driver currently uses a single compatible
for all different models. Split this into the the four well known
subtargets. This allows to get rid of the central mach/soc include
later.
With kernel 6.18 the package shared structure will be hidden from
the phy drivers. Workaround that in advance by providing a shared
private structure that covers all information that is needed for
normal operation.
For further simplification provide a new join() function that takes
care of a consistent initialization.
Daniel Golle [Tue, 23 Dec 2025 14:49:48 +0000 (14:49 +0000)]
mediatek: filogic: asus,rt-ax57m: remove unused pinctrl groups
Remove unused pinctrl groups defined in the device tree, probably as a
result of importing the vendor device tree which is based on the
reference board from MediaTek's SDK.
114b5c2063 ("mediatek: filogic: Add support ASUS RT-AX57M") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2. Connect the PC via LAN to one of the yellow router ports and wait
until your PC to get a DHCP lease.
3. Browse to http://192.168.1.1 (or whatever your router IP is configured as)
4. If your router is brand new, finish the setup process and log into
the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the
downloaded OpenWrt initramfs.trx image.
6. Wait for OpenWrt to boot. Open the default OpenWrt IP in a web browser and perform a system upgrade using the sysupgrade image as instructed in the top banner.
---------------------------------------------------------------------------
Revert to stock firmware:
1: Install package facinstall -> https://forum.openwrt.org/t/facinstall-package-for-easy-installation-factory-images/177587
2. Install Asus stock trx image via OpenWRT LuCI interface.
Signed-off-by: Garrett Mesmer <garrettmesm@gmail.com> Co-authored-by: Oleg S <remittor@gmail.com> Signed-off-by: Oleg S <remittor@gmail.com> Link: https://github.com/openwrt/openwrt/pull/20491 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Jonas Jelonek [Mon, 22 Dec 2025 09:57:52 +0000 (09:57 +0000)]
realtek: image: add rt-loader-no-uimage recipe
Add a new recipe 'rt-loader-no-uimage' that passes the kernel load
address to rt-loader, causing it to use that instead of it's initial run
address.
The usual behavior is fine for uImages where the load address is
predefined in the header, U-boot loads the image to that address and
then runs it, rt-loader just takes over that address. For non-uImage
instead, the address is tightly coupled to where the image has been
transferred during serial or TFTP upload. This may not be possible on
several devices. Passing a separate kernel load address to rt-loader
decouples that and avoids taking the pain to change the load address of
the kernel itself.
projects / thirdparty / openwrt.git / log
