mac80211: Do not build b43legacy on BRCM47xx mips74 subtarget
b43legacy needs ssb support and we do not compile the mips74 subtarget
of the brcm47xx target with SSB support. This causes a build failure in
the mac80211 package and only some of the kernel modules are being
created.
I am not aware of any device with a BRCM47xx mips74 CPU which uses a
b43legacy compatible device.
David Bauer [Thu, 11 Jul 2019 15:15:48 +0000 (17:15 +0200)]
ramips: add support for ASUS RT-AC57U
SoC: MediaTek MT7621AT
RAM: 128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi: MediaTek MT7603EN bgn 2SS
WiFi: MediaTek MT7612EN nac 2SS
BTN: Reset - WPS
LED: - Power
- LAN {1-4}
- WAN
- WiFi 2.4 GHz
- WiFi 5 GHz
- USB
UART: UART is present next to the Power LED.
TX - RX - GND - 3V3 / 57600-8N1
3V3 is the nearest one to the Power LED.
Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
> tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>
Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
> scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
> mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
> reboot
Update the lua5.3 package to build a shared object just like the old lua
package. Ported / recreated the same patch number as the other lua
package. Built and tested library / interpreter on BCM5301X.
mt7621 has the following memory map:
0x0-0x1c000000: lower 448m memory
0x1c000000-0x2000000: peripheral registers
0x20000000-0x2400000: higher 64m memory
detect_memory_region in arch/mips/kernel/setup.c only add the first
memory region and isn't suitable for 512m memory detection because
it may accidentally read the memory area for peripheral registers.
This commit adds memory detection capability for mt7621:
1. add the highmem area when 512m is detected.
2. guard memcmp from accessing peripheral registers:
This only happens when some weird user decided to change
kernel load address to 256m or higher address. Since this
is a quite unusual case, we just skip 512m testing and return
256m as memory size.
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ramips/mt7620: Synchronize Makefiles with DTS compatible
This will "rename" devices in Makefiles to the pattern used in
DTS compatible. This will systematize naming of devices
enormously.
As device names are used to for default SUPPORTED_DEVICES entries,
we need to adjust the source for /tmp/sysinfo/board_name, too.
So remove relevant entries from base-files/lib/ramips.sh and
use device compatible for that.
Despite that, base-files are updated, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
John Crispin [Wed, 10 Jul 2019 11:32:24 +0000 (13:32 +0200)]
include/package.mk: Add support for src-checkout/ folder
This feature is similar to the SRC_TREE_OVERRIDE. However instead of having
to manually create a symlink inside the package folder, the buildsystem
will check if $(TOP_DIR)/src-checkout/$(PKG_NAME)/.git is present and use
this instead.
This fixes the collection of target info during build, where the
device title for rb532/nand is just empty:
tmp/.config-target.in:44925:warning: leading whitespace ignored
tmp/.config-target.in:123738:warning: leading whitespace ignored
tmp/.config-target.in:123786:warning: leading whitespace ignored
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Lucian Cristian [Sun, 30 Jun 2019 06:31:15 +0000 (09:31 +0300)]
kernel: x86: enable NVME support for 64 bit target
Newer motherboards support NVMe U.2 connectors but also NVMe storage can
be used on add-on pcie adapters.
Enable kernel driver on x86 for now so the NVMe flash storage can be used
Chuanhong Guo [Thu, 27 Jun 2019 12:44:27 +0000 (20:44 +0800)]
ramips: use upstream RAW_APPENDED_DTB instead of our OWRTDTB
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit: 02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")
Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8] Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620] Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
kmod-sched-cake: drop out of tree package, use kernel version
CAKE made it to kernel 4.19 and since OpenWrt now at kernel 4.19 we can
drop the out of tree cake package in base repository.
Add kmod-sched-cake to netsupport so package dependencies are still met.
Similarly CAKE is retained as an optional qdisc module to avoid base
scheduler package size implications.
Backport upstream patches from k5.1 to address some small bugs and
support fwmark usage.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Its last usage was dropped back in 2013 in the commit b95bdc8ab56e
("kernel/base-files: clean up old code related to refreshing mtd
partitions, it is no longer used anywhere").
Hauke Mehrtens [Fri, 28 Jun 2019 19:52:41 +0000 (21:52 +0200)]
kernel: Add missing includes mtdsplit_*.c
This fixes the following compile problem with kernel 4.9 on lantiq:
drivers/mtd/mtdsplit/mtdsplit_uimage.c:244:34: error: array type has incomplete element type 'struct of_device_id'
static const struct of_device_id mtdsplit_uimage_of_match_table[] = {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/mtdsplit/mtdsplit_uimage.c:245:4: error: field name not in record or union initializer
{ .compatible = "denx,uimage" },
Andrew Cameron [Sun, 30 Jun 2019 02:45:09 +0000 (21:45 -0500)]
ath79: increase kernel partition size for CPE610v1
Increase the Kernel partition to address the issue discussed here
https://forum.openwrt.org/t/cpe610-v1-sysupgrade-bin-missing-too-big/39637/5
Switch Back to the okli Loader to support increased partition size
Signed-off-by: Andrew Cameron <apcameron@softhome.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [add <> for e-mail]
Emil Muratov [Thu, 1 Nov 2018 18:53:43 +0000 (21:53 +0300)]
busybox: enable swapon/off by default to make it consistent with mkswap
No size increase on busybox binary.
Since busybox mkswap is already enabled by default it seems reasonable
to enable swapon/off too. For ex. this obsoletes installing block-mount
dependency for zram-swap.
Emil Muratov [Wed, 31 Oct 2018 21:16:58 +0000 (00:16 +0300)]
zram-swap: Add zram compaction and statistics info output
Executing '/etc/init.d/zram start' during runtime (with a swap being already
mounted) triggers zram device compaction and prints out nice stats info about
zram memory usage
Signed-off-by: Emil Muratov <gpm@hotplug.ru> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [use IEC's MiB unit]
Emil Muratov [Wed, 31 Oct 2018 08:43:49 +0000 (11:43 +0300)]
zram-swap: Fix busybox dependency check
- fix dependency on BUSYBOX_CONFIG_SWAPONOFF (removed in 84da2a6)
- add busybox defaults checking (fix zram-swap always installs swap-utils
and libblkid as dependency, even if busybox includes mkswap by default)
After commit 1e41de2f48 ("mpc85xx: convert TL-WDR4900 v1 to simpleImage")
XZ compression of zImage was enabled. This change exposed a problem with
the HiveAP-330 images, which was fixed by foregoing the compression on
the kernel altogether with commit 98089bb8ba8
("mpc85xx: Use uncompressed kernel on the HiveAP-330").
This patch adds back the gzip compression of the kernel image by
utilizing the generic OpenWRT uImage method instead of relying on
the PowerPC bootwrapper script that did it previously.
Compile-tested: p1020/hiveap-330
Tested-by: Chris Blake <chrisrblake93@gmail.com> [run-tested] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[filled in even more text]
This edjusts the selection of recently removed wolfssl options which
have always been built into the library even in their abscence.
Also remove the selection of libwolfssl itself, allowing the library to
be built as a module.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Removed options that can't be turned off because we're building with
--enable-stunnel, some of which affect hostapd's Config.in.
Adjusted the title of OCSP option, as OCSP itself can't be turned off,
only the stapling part is selectable.
Mark options turned on when wpad support is selected.
Add building options for TLS 1.0, and TLS 1.3.
Add hardware crypto support, which due to a bug, only works when CCM
support is turned off.
Reorganized option conditionals in Makefile.
Add Eneas U de Queiroz as maintainer.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This includes a fix for a medium-level potential cache attack with a
variant of Bleichenbacher’s attack. Patches were refreshed.
Increased FP_MAX_BITS to allow 4096-bit RSA keys.
Fixed poly1305 build option, and some Makefile updates.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The following warnings are introduced by our own patches:
lantiq_etop.c:173:1: warning: no semicolon at end of struct or union
};
^
lantiq_etop.c: In function 'ltq_etop_change_mtu':
lantiq_etop.c:725:2: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
int max = ETH_HLEN + VLAN_HLEN + new_mtu + ETH_FCS_LEN;
^~~
Petr Štetiar [Sun, 30 Dec 2018 11:17:25 +0000 (12:17 +0100)]
lantiq: dts: use generic node names
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[split out treewide patch, integrated P2812HNUF1 rename patch] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[merged key and led changes, use generic node name for flash, wifi and
gpio] Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias Kresin [Sun, 27 Jan 2019 15:34:33 +0000 (16:34 +0100)]
lantiq: dts: move localbus childs to dts
The localbus childs are highly board specific and need to be part of the
board dts. Otherwise we run into duplicate unit address issues if a
board has something else (NAND) connected to the bus id.
Paul Spooren [Sun, 16 Jun 2019 19:34:46 +0000 (21:34 +0200)]
ath79: split DEVICE_TITLE in multiple variables
This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and
DEVICE_VARIANT. All three are merged together to look the same as the
current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as
a *fallback* for devices which weren't upgraded yet.
This is based on the work of @sudhanshu16.
The motivation is to create JSON files based on provided metadata,
needing clear differentiation between vendor, model and revision.
projects / thirdparty / openwrt.git / log
