Hauke Mehrtens [Mon, 4 Oct 2021 21:48:20 +0000 (23:48 +0200)]
mac80211: Update to version 5.11.22-1
The removed patches were applied upstream.
This backports version 5.11.22 and later does not support kernel
versions < 4.4, this allows us to remove some patches too.
e983a25 Update regulatory rules for Ecuador (EC) a0bcb88 wireless-regdb: Update regulatory rules for Norway (NO) on 6 and 60 GHz cdf854d wireless-regdb: Update regulatory rules for Germany (DE) on 6GHz 86cba52 wireless-regdb: reduce bandwidth for 5730-5850 and 5850-5895 MHz in US 6fa2384 wireless-regdb: remove PTMP-ONLY from 5850-5895 MHz for US 9839e1e wireless-regdb: recent FCC report and order allows 5850-5895 immediately 42dfaf4 wireless-regdb: update 5725-5850 MHz rule for GB
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Deomid Ryabkov [Sat, 23 Oct 2021 13:22:39 +0000 (16:22 +0300)]
base-files: chmod 1777 /var/lock
Per FHS 3.0, /var/lock is the location for lock files [1].
However its current permissions (755) are too restrictive
for use by unprivileged processes.
Debian and Ubuntu set them to 1777, and now so do we.
Signed-off-by: Deomid Ryabkov <rojer@rojer.me>
[fixed typo in commit message, had to remove "rojer" due to git hooks] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Sven Eckelmann [Sat, 23 Oct 2021 09:27:35 +0000 (11:27 +0200)]
ath79: ag71xx: Disable napi related interrupts during probe
ag71xx_probe is registering ag71xx_interrupt as handler for the gmac0/gmac1
interrupts. The handler is trying to use napi_schedule to handle the
processing of packets. But the netif_napi_add for this device is
called a lot later in ag71xx_probe.
It can therefore happen that a still running gmac0/gmac1 is triggering the
interrupt handler with a bit from AG71XX_INT_POLL set in
AG71XX_REG_INT_STATUS. The handler will then call napi_schedule and the
napi code will crash the system because the ag->napi is not yet
initialized:
The gmcc0/gmac1 must be brought in a state in which it doesn't signal a
AG71XX_INT_POLL related status bits as interrupt before registering the
interrupt handler. ag71xx_hw_start will take care of re-initializing the
AG71XX_REG_INT_ENABLE.
Fixes: f529a3742043 ("surprise :p") Signed-off-by: Sven Eckelmann <sven@narfation.org>
This allows to specify and control switch LEDs on devices using mt7530
(typically mediatek and ramips targets).
Normally these LED GPIOs are 0, 3, 6, 9, and 12. wan/lan assignment is
per device. GPIO 9 is normally inverted. so GPIO_ACTIVE_HIGH instead of
GPIO_ACTIVE_LOW.
Tan Zien [Fri, 22 Oct 2021 20:15:08 +0000 (04:15 +0800)]
ipq40xx: MR33: Fix LP5562 LED driver probe
Add the reg and color property to each channel node. This update is
to accommodate the multicolor framework.
Refer to:
<https://lore.kernel.org/all/20200622185919.2131-9-dmurphy@ti.com>
<https://lore.kernel.org/all/20210818070209.1540451-1-michal.vokac@ysoft.com>
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[replaced links to lore, wrote something of a commit message] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates all current APM82181 devices over to that
"new LED naming scheme". This includes many updates to the
device-tree:
- dropped the deprecated, but beloved "label" property.
- rename all DT leds node names to led-#.
- add function and color properties.
- utilized panic-indicator property.
- dropped led- aliases (see below).
migration scripts for all devices are included.
For more information. See:
<https://www.kernel.org/doc/html/latest/leds/leds-class.html>
For the future: It looks like the color+function properties
won over the dt-alias / label. This will need to be wired up
into openwrt eventually. For APM821xx the situation is that
all devices have a dedicated power and fault indicator.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Back in the AR71XX days, the lzma-loader code could be customized
based on the $BOARD variable. These would be passed as a
compile-time -DCONFIG_BOARD_$DEVICE_MODEL flag to the compiler.
Hence, the lzma-loader would be able to include device-specific
fixups.
Note: There's still a fixup for the TpLink TL-WR1043ND V1 found
in the lzma-loader's board.c code. But since the days of AR71XX
I couldn't find a forum post or bug reported. So, I left it
as is to not break anything by enabling it.
=> If you have a TL-WR1043ND V1 and you have problem with
the ethernet: let me know. Because otherwise, the fixup
might simply no longer needed with ath79 and it can be removed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The MX60's kernel is limited to 0x3EFC00 by the values in
mkmerakifw.c. Since the initramfs method of loading the
kernel seems to be working, this patch does away with the
use of the mkmerakifw tool for the MX60(W).
But this will go along with a change in u-boot as well.
So before you upgrade, please attach the serial cable and
perform:
| setenv owrt510_boot run meraki_ubi owrt_bootargs\; run owrt_load1 owrt_bootkernel\; run owrt_load2 owrt_bootkernel
| setenv bootcmd run owrt510_boot
| saveenv
Note: You won't be able to use older OpenWrt releases without
switching the bootcmd back to owrt_boot!
Note2: We are no longer compatible with older OpenWrt MX60 installs.
the legacy BOARD_NAME and SUPPORTED_DEVICES can be dropped. This is
because upgrades from older images are not possible without uboot env
changes anymore. Also the bogus BLOCKSIZE value
(which was set to 63k back then, in order to get the kernel properly
aligned after the fdt + meraki header) can be set to the NANDs real
value. The FDT size (which was needed for alignment) can now be
slimmed down as well.
Co-developed-by: Martin Kennedy <hurricos@gmail.com> Signed-off-by: Martin Kennedy <hurricos@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
apm821xx: MBL: HDD regulators overhaul for MBL DUO
Takimata reported on the OpenWrt forum in thread [0], that his
MyBook Live Duo wasn't booting OpenWrt 21.02 after upgrading
from the previous OpenWrt 19.07.
The last logged entries on his console
|[ 0.531599] sata1-regulator GPIO handle specifies active low - ignored
|[ 0.538391] sata0-regulator GPIO handle specifies active low - ignored
|[ 0.759791] ata2: SATA link down (SStatus 0 SControl 300)
|[ 0.765251] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
|[ 5.909555] ata1.00: qc timeout (cmd 0xec)
|[ 5.913656] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
|[ 6.231757] ata1: SATA link down (SStatus 0 SControl 300)
This extract clearly showed that the HDD on which OpenWrt is installed,
simply disappeared after the SATA power regulators had been initialized.
The reason why this worked with OpenWrt 19.07 was because the kernel
config symbol CONFIG_REGULATOR=y was not set in the target's config-4.14.
(This shows that the MBL Single does differ from the DUO in that
it does not have programmable power regulators for the HDDs.)
This patch removes CONFIG_MTD_SPI_NOR_USE_4K_SECTORS from the default
symbols for the ath79/mikrotik target.
MikroTik devices hold some of their user-configurable settings in the
soft_config partition, which is typically sized 4 KiB, of the SPI NOR
flash memory. Previously, in the ar71xx target, it was possible to use
64 KiB erase sectors but also smaller 4 KiB ones when needed. This is
no longer the case in ath79 with newer kernels so, to be able to write
to these 4 KiB small partitions without erasing 60 KiB around, the
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS symbol was added to the defaults.
However, this ended up making sysupgrade images which were built with
64 KiB size blocks not to keep settings (e.g., the files under
/etc/config/) over the flashing process.
Using 4 KiB erase sector size on the sysupgrade images (by setting
BLOCKSIZE = 4k) allows keeping settings over a flashing process, but
renders the process terribly slow, possibly causing a user to
mistakenly force a manual device reboot while the process is still on-
going. Instead, ditching the 4 KiB erase sectors for the default
64 KiB erase size provides normal SPI write speed and sysupgrade times,
at the expense of not being able to modify the soft_config partition
(which is rarely a required thing).
An OpenWrt patch for MTD_SPI_NOR_USE_4K_SECTORS_LIMIT may once have
allowed to use different per-partition erase sector sizes. Due to
changes on recent kernels it now only works on a per-device basis.
Also, partial eraseblock write can be performed in ath79 with kernels
5.4 and lower, by copying the blocks from the 64 KiB, erasing the whole
sector and restoring those blocks not meant to be modified. A kernel
bump had that patch broken for a long time, but got fixed in bf2870c.
Note: the settings in the soft_config partition can be reset to their
defaults by holding the reset button for 5 seconds (and less than 10
seconds) at device boot.
Felix Fietkau [Wed, 20 Oct 2021 19:13:10 +0000 (21:13 +0200)]
hostapd: fix a race condition on adding AP mode wds sta interfaces
Both hostapd and netifd attempt to add a VLAN device to a bridge.
Depending on which one wins the race, bridge vlan settings might be incomplete,
or hostapd might run into an error and refuse to service the client.
Fix this by preventing hostapd from adding interfaces to the bridge and
instead rely entirely on netifd handling this properly
Jitao Lu [Sun, 17 Oct 2021 06:16:57 +0000 (14:16 +0800)]
ncurses: add tmux terminfo
They're preferred terminal descriptions for tmux, with additional support to
some special characters and italic fonts. More info can be found at:
https://github.com/tmux/tmux/wiki/FAQ
Fixes: FS#3404 Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
David Bauer [Sun, 17 Oct 2021 21:29:57 +0000 (23:29 +0200)]
hostapd: fix goto loop for ubus assoc handler
When a ubus event handler denies a association with a non-zero return
value, the code jumps to preceeding code, creating an endless loop until
the event handler accepts the assc request.
Move the ubus handler further up the code to avoid creating such a loop.
wireguard-tools: add uci option to disable wireguard peers
Right now when I want to temporarily disable wg peer I need to delete
the entire peer section. This is not such a good solution because I
loose the previous configuration of the peer.
This patch adds `disabled` option to peer config which causes that
the config section is ignored.
Signed-off-by: Stepan Henek <stepan.henek@nic.cz>
[use $(AUTORELEASE)] Signed-off-by: Paul Spooren <mail@aparcar.org>
Andre Heider [Sat, 2 Oct 2021 08:50:49 +0000 (10:50 +0200)]
wolfssl: always build with --enable-reproducible-build
This gates out anything that might introduce semantically frivolous jitter,
maximizing chance of identical object files.
The binary size shrinks by 8kb: 1244352 staging_dir/target-mipsel_24kc_musl/usr/lib/libwolfssl.so.4.8.1.39c36f2f 1236160 staging_dir/target-mipsel_24kc_musl/usr/lib/libwolfssl.so.4.8.1.39c36f2f
Andre Heider [Wed, 6 Oct 2021 08:54:48 +0000 (10:54 +0200)]
wolfssl: build with WOLFSSL_ALT_CERT_CHAINS
"Alternate certification chains, as oppossed to requiring full chain
validataion. Certificate validation behavior is relaxed, similar to
openssl and browsers. Only the peer certificate must validate to a trusted
certificate. Without this, all certificates sent by a peer must be
used in the trust chain or the connection will be rejected."
This fixes e.g. uclient-fetch and curl connecting to servers using a Let's
Encrypt certificate which are cross-signed by the now expired
DST Root CA X3, see [0].
This is the recommended solution from upstream [1].
The binary size increases by ~12.3kb: 1236160 staging_dir/target-mipsel_24kc_musl/usr/lib/libwolfssl.so.4.8.1.39c36f2f 1248704 staging_dir/target-mipsel_24kc_musl/usr/lib/libwolfssl.so.4.8.1.39c36f2f
Felix Fietkau [Sun, 17 Oct 2021 14:05:34 +0000 (16:05 +0200)]
ramips: remove kmod-mt7663-firmware-sta from device packages
This firmware should only be used for mobile devices (e.g. laptops), where
AP mode functionality is typically not used. This firmware supports a lot
of power saving offload functionality at the expense of AP mode support.
Daniel Golle [Fri, 20 Aug 2021 17:31:48 +0000 (18:31 +0100)]
mediatek: add EEPROM data for BPi-R64 2.4GHz wmac
EEPROM data extracted from vendor image found at
http://forum.banana-pi.org/t/bpi-r64-mt7622-mac80211-wifi-driver/10246/77
http://forum.banana-pi.org/uploads/short-url/jworbyBYpvrw9VQ2sx92B9z6DWS.bin
MAC address in the EEPROM has been zero'd which results in random
address on boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
David Bauer [Sat, 5 Dec 2020 19:17:35 +0000 (20:17 +0100)]
hostapd: ubus: add BSS transtiton request method
The existing wnm_disassoc_imminent ubus method only supports issuing a
bss transition request with the disassoc imminent flag set.
For use-cases, where the client is requested to roam to another BSS
without a pending disassoc, this existing method is not suitable.
Add a new bss_transition_request ubus method, which provides a more
universal way to dispatch a transition request. It takes the following
arguments:
Required:
addr: String - MAC-address of the STA to send the request to (colon-seperated)
Optional:
abridged - Bool - Indicates if the abridged flag is set
disassociation_imminent: Bool - Whether or not the disassoc_imminent
flag is set
disassociation_timer: I32 - number of TBTTs after which the client will
be disassociated
validity_period: I32 - number of TBTTs after which the beacon
candidate list (if included) will be invalid
neighbors: blob-array - Array of strings containing neighbor reports as
hex-string
David Bauer [Wed, 21 Oct 2020 18:50:01 +0000 (20:50 +0200)]
hostapd: ubus: add notification for BSS transition response
To allow steering daemons to be aware of the STA-decided transition
target, publish WNM transition responses to ubus. This way, steerings
daemons can learn about STA-chosen targets and send a better selection
of transition candidates.
Felix Fietkau [Wed, 13 Oct 2021 14:36:16 +0000 (16:36 +0200)]
tools/fakeroot: explicitly pass CPP variable
For some reason, the generated configure script fails to properly set up
the internal preprocessor command variable, causing the host OS check for
Darwin to fail after the last update.
Explicitly setting CPP fixes this issue
Paul Spooren [Mon, 11 Oct 2021 20:33:26 +0000 (10:33 -1000)]
x86/64: enable MMIO_CMDLINE_DEVICES for firecracker support
This Kernel option allows to run OpenWrt witin a `firecracker` micro VM.
Firecracker is a KVM-based tool for superfast booting VMs on x86_64 and
aarch64. It makes rootfs available to the guest as a virtio-mmio device
and passes its address via the kernel cmdline. A kernel without
CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES will not recognize the rootfs
virtio-mmio device.
Suggested-by: Packet Please <pktpls@systemli.org> Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Mon, 11 Oct 2021 20:29:40 +0000 (10:29 -1000)]
armvirt: enable MMIO_CMDLINE_DEVICES for firecracker support
This Kernel option allows to run OpenWrt witin a `firecracker` micro VM.
Firecracker is a KVM-based tool for superfast booting VMs on x86_64 and
aarch64. It makes rootfs available to the guest as a virtio-mmio device
and passes its address via the kernel cmdline. A kernel without
CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES will not recognize the rootfs
virtio-mmio device.
Suggested-by: Packet Please <pktpls@systemli.org> Signed-off-by: Paul Spooren <mail@aparcar.org>
Daniel Golle [Tue, 12 Oct 2021 23:38:12 +0000 (00:38 +0100)]
procd: update to git HEAD
97bcdcf uxc: fix segfault caused by use-after-free 6398e05 uxc: don't free the stack 324ebd0 jail: fs: add support for asymmetric mount bind c44ab7f jail: netifd: generate netifd uci config and mount it 82dd390 jail: make use of per-container netifd via ubus
The new per-jail netifd is now configured by filtering the host
network configuration. As libuci is used for that, procd-ujail now
depends on libuci.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
As Hauke commented, this causes builder failures on 5.4 kernels.
This revert includes changes to the mx100 kernel modules
dependency as well as the uci led definitions.
Tested-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Szabolcs Hubai [Sat, 9 Oct 2021 23:32:30 +0000 (01:32 +0200)]
ipq40xx: use zImage for GL.iNet GL-B1300, GL-S1300 to shrink below 4096k
In the "ipq40xx: switch to Kernel 5.10" discussion at GitHub,
Adrian noted [0] that these GL.iNet Conexa series devices,
GL-B1300 and GL-S1300 failed their image generation [1] as their gzipped
uImage kernel went above 4096k.
While notifying the vendor about this problem [2], I tested all U-Boot
releases from GL.iNet:
- they really fail to boot kernel above 4096k
- they don't support lzma: "Unimplemented compression type 3"
- but they boot zImage
Using zImage (xz compression) the kernel is 2909k which is
more than a megabyte away from the KERNEL_SIZE := 4096k limit.
The gzip compressed version would be 4116k.
[0]: https://github.com/openwrt/openwrt/pull/4620#issuecomment-932765776
[1]: commit 7b1fa276f5a2 ("ipq40xx: add testing support for kernel 5.10")
[2]: https://forum.gl-inet.com/t/ipq40xx-kernel-size-and-u-boot-v5-10-is-too-big-for-4-mb/17619
UART:
The UART header is named CONN11 and is found in the
center of the mainboard. The pinout from Pin 1 (marked
with a black triangle) to pin 4 is below:
Pin 1: VCC
Pin 2: TX
Pin 3: RX
Pin 4: GND
Note that VCC is not required for UART on this device.
Booting:
1. Flash/burn one of the images from this repo to a
flash drive.
2. Take the top off the MX100, and unplug the SATA
cable from the HDD.
3. Hook up UART to the MX100, plug in the USB drive,
and then power up the device.
4. At the BIOS prompt, quickly press F7 and then
scroll to the Save & Exit tab.
5. Scroll down to Boot Override, and select the
UEFI entry for your jumpdrive.
Note: UEFI booting will fail if the SATA cable for
the HDD is plugged in.
The issue is explained under the Flashing instructions.
Flashing:
1. Ensure the MX100 is powered down, and not plugged
into power.
2. Take the top off the MX100, and unplug the SATA
cable from the HDD.
3. Using the Mini USB female port found by the SATA
port on the motherboard,
flash one of the images to the system. Example:
`dd if=image of=/dev/sdb conv=fdatasync` where sdb
is the USB device for the MX100's NAND.
4. Unplug the Mini USB, hook up UART to the MX100,
and then power up the device.
5. At the BIOS prompt, quickly press F7 and then
scroll to the Boot tab.
6. Change the boot order and set UEFI: USB DISK 2.0
as first, and USB DISK 2.0 as second.
Disable the other boot options.
7. Go to Save & Exit, and then select Save Changes and
Reset
Note that OpenWRT will fail to boot in UEFI mode when
the SATA hard drive is plugged in. To fix this, boot
with the SATA disk unplugged and then run the following
command:
`sed -i "s|hd0,gpt1|hd1,gpt1|g" boot/grub/grub.cfg`
Once the above is ran, OpenWRT will boot when the HDD
is plugged into SATA. The reason this happens is the
UEFI implementation for the MX100 will always set
anything on SATA to HD0 instead of the onboard USB
storage, so we have to accomidate it since OpenWRT's
GRUB does not support detecting a boot disk via UUID.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Chris Blake [Fri, 24 Sep 2021 13:42:03 +0000 (08:42 -0500)]
gpio-cdev: add nu801 userspace driver
This adds a userspace interpretation of the nu801 driver used by Meraki
hardware. Previously this was a driver that was added per target, but as
multiple targets now have this driver, we should move to something that
can be shared by all targets since no driver exists upstream.
Co-developed-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
try to reduce the kernel size by disabling and moving
options from the common kernel configuration to the
SATA target that doesn't have the constraints.
For NAND this has become necessary because as with 5.10
some devices outgrew their kernels. Though, in my tests
this didn't help much: just a smidgen over 100kib was
saved on the uncompressed kernel.
... running make kernel_oldconfig also removed some
other config symbols, mostly those that already set
from elsewhere or became obsolete in the meantime.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Linus Walleij [Sat, 9 Oct 2021 11:32:09 +0000 (13:32 +0200)]
gemini: splash banner on framebuffer console
The D-Link DIR-685 has a small screen with a framebuffer
console, so if we have this, when we start, display the
banner on this framebuffer console so the user know they
are running OpenWRT as root filesystem.
apm821xx: WNDAP620 + WNDAP660: reorganize partitions for 5.10
Due to 5.10 increased kernel size, the current 4MiB-ish kernel
partition got too small. Luckily, netgear's uboot environment
is setup to read 0x60000 bytes from the kernel partition location.
... While at it: also do some cleanups in the DTS in there.
The original (re-)installation described in
commit d82d84694e60 ("apm821xx: add support for the Netgear WNDAP620 and WNDAP660")
seemed to be still working for now. What I noticed though
is that the bigger initramfs images needed to use a different
destination address (1000000) to prevent it overwriting
itself during decompression. i.e:
# tftp 1000000 openwrt-...-wndap620-initramfs-kernel.bin
# bootm
However, in case of the WNDAP620+660 the factory.img image can be
written directly to the flash through uboot.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
apm821xx: move CONFIG_DMA* to the generic apm821xx config
Both NAND and SATA targets need the DMA engine in one way
or another.
Due to a kernel config refresh various existing symbols
got removed from the apm821xx main config file as well.
(That being said, they are still included because the
built-in crpyto4xx depends on these.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
projects / thirdparty / openwrt.git / log
