Michal Simek [Fri, 10 Nov 2023 12:34:35 +0000 (13:34 +0100)]
arm64: zynqmp: Add multiboot support for SPL/SPI offset calculation
In case of A/B update systems there should be an option to load the same
binary/binaries to different location and they should work.
Before this patch boot.bin with U-Boot SPL can be added to whatever 32k
offset in SPI and SPL finds u-boot.itb at CONFIG_SYS_SPI_U_BOOT_OFFS
offset. In case of A/B update systems that means that SPL is at different
locations but it still points to the same u-boot.itb which is not correct.
That's why include multiboot value to offset calculation to be able to
point to image from the same base.
It doesn't affect any current system which starts from 0 offset.
This patch also change Kria defconfig which uses A/B setup. Partition
A starts at multiboot 64, partition B at multiboot 496.
And also print message about used SPI offset which is useful for all cases.
Mayuresh Chitale [Thu, 16 Nov 2023 16:43:36 +0000 (22:13 +0530)]
drivers: xilinx_spi: Probe fifo_depth at runtime
If the fifo-size DT parameter is not provided then probe the
controller's fifo depth at runtime. This is ported from a patch
in the Linux Xilinx SPI driver.
Mayuresh Chitale [Thu, 16 Nov 2023 16:43:34 +0000 (22:13 +0530)]
drivers: xilinx_spi: Use udevice in start_tranfer
Modify start_transfer and related functions to take a udevice parameter
as input instead of spi_slave. This is needed so that start_transfer can
be used directly via the xfer callback. Also fix a compiler warning.
Michal Simek [Mon, 13 Nov 2023 09:05:28 +0000 (10:05 +0100)]
xilinx: zynq: Enable capsule update for Antminer S9
Capsule update helps with easier firmware development that's why enable it
by default to be able to update system without replugging SD card again and
again.
Michal Simek [Mon, 13 Nov 2023 09:05:27 +0000 (10:05 +0100)]
xilinx: zynq: Generate dfu for SPI only when enabled
Bitmain S9 board is not enabling SPI that's why CONFIG_SYS_SPI_U_BOOT_OFFS
symbol is not present which ends in build failure when EFI/DFU
infrastructure is enabled.
Mayuresh Chitale [Thu, 16 Nov 2023 16:51:03 +0000 (22:21 +0530)]
pci: xilinx: Enable MMIO region
The host bridge MMIO region is disabled by default due to which MMIO
accesses cause an exception. Fix it by setting the bridge enable bit.
This change is ported from the linux pcie-xilinx driver.
Mayuresh Chitale [Thu, 16 Nov 2023 16:40:24 +0000 (22:10 +0530)]
net: axi_emac: Use reg property for DMA registers
As per the xlnx,axi-ethernet-1.00.a DT documentation in linux, the AXI
DMA registers can be obtained via the reg property or via a separate
node for the axistream DMA controller. Currently only the latter is
supported, so add support to fetch the DMA controller registers from the
"reg" property.
Michal Simek [Wed, 8 Nov 2023 07:36:40 +0000 (08:36 +0100)]
arm64: zynqmp: Remove description for 8T49N240
8T49N240 driver was never upstreamed by IDT and there is no user of this
driver that's why remove description for this chip with also remove this
driver.
Michal Simek [Mon, 6 Nov 2023 15:55:48 +0000 (16:55 +0100)]
arm64: zynqmp: Do not expose usbhub nodes
Upstream dwc3 U-Boot driver is not able to handle child nodes properly
that's why comment them in DT for now. This patch should be reverted when
dwc3 driver handles it properly.
DT node itself is aligned with dt schema.
Tom Rini [Tue, 12 Dec 2023 21:32:30 +0000 (16:32 -0500)]
Merge tag 'u-boot-imx-20231212' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
- Fix emmc detection on colibri_imx7
- Fix DDR configuration on tqma6 to improve Ethernet performance
- Fix aliases and chosen nodes indentation on imx7s-warp
- Convert pico-imx6ul to DM_SERIAL
- Convert pico-pi-imx7d to watchdog driver model to fix 'reset' command
- Select CONFIG_NET_RANDOM_ETHADDR on imx8mp_evk to fix networking on
older boards
- Add USBH_EN gpio hog to fix USB host interface not working on some
Apalis Toradex carrier boards with Apalis iMX8 SoM
- Add PCI fixup for GW73xx-F+
- Fix broken EEPROM read on imx8mn-var-som
Marcel Ziswiler [Tue, 12 Dec 2023 11:28:15 +0000 (08:28 -0300)]
board: colibri_imx7: fix emmc detection
Later versions of Colibri iMX7D V1.1B modules use a "new" SoC fusing. The
difference lies in whether we enable the boot ROM to use the eMMC reset
signal. Depending on the SoC fuse, the boot ROM configures this pin as a
GPIO output to drive the reset signal. Our eMMC vs NAND detection
currently only sets that signal to a GPIO without explicitly setting any
direction. Previously, by default, it was set as an input. As the boot ROM
now configures it as an output, we receive a value of zero instead of one,
indicating the absence of the pull-up on eMMC modules.
To fix this, set the SION bit, allowing the reading back of the value
even if it is configured as an output by the boot ROM. It's important to
note that with the new SoC fusing, we now read back what the boot ROM
drives rather than the real value caused by the pull-up resistor. However,
if it were ever driven low, the eMMC would permanently be reset.
In addition, remove hard-coded variant in the eMMC build case as since the
commit 0c39564d0281 ("toradex: colibri_imx7: Enable nand/emmc detection
and set boot variant") will anyways always get overridden by the detection
routing in board code.
Fixes: 0c39564d ("toradex: colibri_imx7: Enable nand/emmc detection and set boot variant") Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Miquel Raynal [Fri, 17 Nov 2023 15:00:44 +0000 (16:00 +0100)]
tqma6: Fix DDR configuration
Initially investigating a Linux network issue causing a lot of drop and
poor network performances on a custom system based on a TQMA6A module
(based on an iMX6Q), [1st link below].
I eventually correlated my observations with a contention at the NIC
level when in concurrency with the graphics pipeline. Troubleshooting
this in the kernel lead to disabling DMA bursts accesses made by the IPU
in order to avoid triggering the QoS at the interconnect level, reducing
from 50 to 10% the drop rate on eth0, [2nd link below]. The solution
worked on my setup but not on others, which still suffered from
abnormally high drop rates even with this "fix".
After looking a while into TQ Systems BSP I figured out a number of
differences in recent U-Boot out-of-tree patches they had in their
repository [3rd link]. Parsing the differences one after the other lead
me to this final solution.
The reset pad of the DDR controller was apparently misconfigured, Bit
18-19 picturing the "DDR select field". The current value b11 is
reserved. The only defined value as of version 6 of the iMX6Q manual was
b00 "DDR3 and LPDDR2 mode". In practice no register difference has been
spotted after changing this configuration but all issues tracked thus
far just vanished. All previous fixes have been proven irrelevant. Just
clearing this field solved all our network issues and the drop rate as
measured by iperf3 felt back to 0%.
Fabio Estevam [Thu, 26 Oct 2023 12:16:36 +0000 (09:16 -0300)]
imx8mp_evk: Select CONFIG_NET_RANDOM_ETHADDR
On an early revision of the imx8mp-evk that I have access to,
the MAC addresses fuses are not programmed, causing failure to bring
the Ethernet interfaces.
Fix this problema by selecting CONFIG_NET_RANDOM_ETHADDR so that
random MAC addresses are assigned and the Ethernet ports become
functional out of the box.
USB host interface is not working on some Apalis Toradex carrier
boards with Apalis iMX8 SoM. This is due to USBH_EN pin, which
powers USB peripherals, having a strong pull-down on some boards,
and a weak pull-down on the others. This USBH_EN pin is left
unconfigured, which means it is in its default state at cold boot:
input with a strong pull-up. As a result, carrier boards with a
weak pull-down have this signal high enough to trigger power
delivery to USB peripherals, and opposite - boards with strong
pull-down on USBH_EN have this signal below the threshold needed
to trigger USB power delivery.
This change configures the USBH_EN pin as gpio hog, fixing this
issue for all Apalis carrier boards regardless of pull-down
resistor value.
Also, update apalis-imx8_defconfig via savedefconfig.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
- StarFive: Add StarFive watchdog driver
- VisionFive2: Support device tree overlay for VisionFive2 board
- Andes: Fix PLIC-SW setting
- RISC-V: Fix NVMe support by implying NVME_PCI for QEMU
- RISC-V: Fix binman for 64 bit format load address
Tom Rini [Sat, 9 Dec 2023 18:16:14 +0000 (13:16 -0500)]
Merge patch series "bootflow: bootmeth_efi: Fix network efi boot."
To quote the author:
Currently bootmeth_efi crashes while doing a network (dhcp) boot.
This patch series fixes issues and both network and disk boot works.
# Do not modify or remove the line above.
# Everything below it will be ignored.
#
# Please enter a commit message to explain why this merge is necessary,
# especially if it merges an updated upstream into a topic branch.
#
# An empty message aborts the commit.
Shantur Rathore [Sun, 19 Nov 2023 16:54:58 +0000 (16:54 +0000)]
bootflow: bootmeth_efi: Set bootp_arch as hex
bootmeth_efi sets up bootp_arch which is read later in bootp.c
Currently bootp_arch is being set as integer string and being
read in bootp.c as hex, this sends incorrect arch value to dhcp server
which in return sends wrong file for network boot.
For ARM64 UEFI Arch value is 0xb (11), here we set environment as 11
and later is read as 0x11 and 17 is sent to dhcp server.
Setting it as hex string fixes the problem.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Shantur Rathore <i@shantur.com>
Janne Grunau [Fri, 1 Dec 2023 07:12:33 +0000 (08:12 +0100)]
arm: apple: t602x: Add missing MMIO regions to memmap
The memory maps for Apple's M2 Pro/Max/Ultra left MMIO space out which
was not used by any driver at the time. The display out exposed as
simple-framebuffer use a power-domain controlled by a device in an
unmapped region.
Add a map covering this region as well as another MMIO region in the
range 0x4'0000'0000 - 0x5'0000'0000. The added regions cover all MMIO
annotated in Apple's device tree in this range.
Signed-off-by: Janne Grunau <j@jannau.net> Reviewed-by: Eric Curtin <ecurtin@redhat.com> Reviewed-by: Neal Gompa <neal@gompa.dev> Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Marek Vasut [Sat, 7 Oct 2023 21:41:03 +0000 (23:41 +0200)]
test: bdinfo: Test both bdinfo and bdinfo -a
Factor out the core of test for all bdinfo output into bdinfo_test_all()
and then reuse it to verify that both 'bdinfo' and 'bdinfo -a' print all
the bdinfo output.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Sat, 7 Oct 2023 21:40:58 +0000 (23:40 +0200)]
cmd: bdinfo: Optionally use getopt and implement bdinfo -a
Add optional support for getopt() and in case this is enabled via
GETOPT configuration option, implement support for 'bdinfo -a'.
The 'bdinfo -a' behaves exactly like bdinfo and prints 'all' the
bdinfo information. This is implemented in preparation for other
more fine-grained options.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
spi: cadence_qspi: Select flash subnode at runtime
Currently spi driver gets flash parameter from first subnode.
Few boards have more than one flash with different parameters
and selection of flash is done by on board switch settings.
In such case, uboot needs to be recompiled with updated
device tree to align with board switch settings.
This patch allows to select flash node at runtime.
Boards those are supporting multiple flashes
needs to implement cadence_qspi_get_subnode function and return correct
flash node.
Cc: Apurva Nandan <a-nandan@ti.com> Signed-off-by: Udit Kumar <u-kumar1@ti.com> Reviewed-by: Neha Malcom Francis <n-francis@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
mtd: spi-nor: Add MT25U01G part number for SPI NOR Flash
MT25QU01 OPN with 4B OPCODE support is currently not supported in
source code and the driver reuses the definition for "n25q00a"
which has the same silicon ID but is a slower part.
Adding mt25u01g definition to the source code to support a faster
read response for MT25QU01 QSPI NOR Flash device.
Signed-off-by: Jit Loon Lim <jit.loon.lim@intel.com>
[jagan: fix the id position and commit head] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tom Rini [Sat, 9 Dec 2023 03:00:01 +0000 (22:00 -0500)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
The first four patches are actual fixes. The last three patches add
support for the apparently popular OrangePi Zero 3 board: multiple
people seem to be champing at the bit, so I'd rather give them
something real instead of people using random trees they found on the
Internet. It's actually mostly the new defconfig file anyway, so the
chances for regressions are very slim.
Tom Rini [Sat, 9 Dec 2023 00:03:03 +0000 (19:03 -0500)]
Merge tag 'efi-2024-01-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2024-01-rc5
Documentation:
* Update and correct support notes on clang
* sandbox: Fix VPL instructions
UEFI:
* Fix a bug in DisconnectController
* Provide better error messages for missing CONFIG_EFI_CAPSULE_ESL_FILE
* Create EFI memory reservations when booting via ACPI
* Make ACPI tables accessible in EFI app
Neil Armstrong [Wed, 6 Dec 2023 09:04:21 +0000 (10:04 +0100)]
configs: meson: enable missing DM_USB_GADGET
Since commit b96640cbfb ("ARM: meson: g12a: switch dwc2 otg to DM")
and commit e327e2affd ("ARM: meson: switch AXG & GX dwc2 otg to DM")
Amlogic boards now requires DM_USB_GADGET to have USB Gadget to work.
Add it to the boards configs as returned by:
$ grep -L DM_USB_GADGET $(grep -l CONFIG_USB_GADGET $(grep -l MESON configs/*))
Andre Przywara [Wed, 18 Oct 2023 00:06:52 +0000 (01:06 +0100)]
sunxi: H616: Add OrangePi Zero 3 board support
The OrangePi Zero 3 is a small development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI
connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for
which was recently added to U-Boot.
Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Mikhail Kalashnikov <iuncuim@gmail.com> Tested-by: Bob McChesney <bob@electricworry.net> Tested-by: Stephen Graf <stephen.graf@gmail.com>
Andre Przywara [Tue, 17 Oct 2023 16:08:52 +0000 (17:08 +0100)]
sunxi: H616: remove default AXP305 selection
The original H616 devices released about three years ago were typically
paired with an X-Powers AXP305 PMIC. Newer devices uses the smaller
AXP313, and there seem to be far more systems with this PMIC around now.
Remove the default AXP305 selection for the H616 SoC from the Kconfig,
and move the PMIC selection into the board defconfig files instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Chukun Pan [Sun, 29 Oct 2023 07:40:09 +0000 (15:40 +0800)]
sunxi: dts: arm64: update emac for Orange Pi Zero 3
The current emac setting is not suitable for Orange Pi Zero 3,
move it back to Orange Pi Zero 2 DT. Also update phy mode and
delay values for emac on Orange Pi Zero 3.
With these changes, Ethernet now looks stable.
Fixes: 95c3b0635ea4 ("sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Stephen Graf [Fri, 1 Dec 2023 18:50:39 +0000 (10:50 -0800)]
sunxi: correct documentation for SPI flashing
The mtd_debug write does not work in this context. The flashcp command does
work, provides both the erase and write functions and with the verbose
option gives good feedback.
Signed-off-by: Stephen Graf <stephen.graf@gmail.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Wed, 13 Jul 2022 15:27:57 +0000 (16:27 +0100)]
sunxi: h616: (really) lower SPL stack address to avoid BROM data
When using the USB OTG FEL mode on the Allwinner H616, the BootROM
stores some data at the end of SRAM C. This is also the location where
we place the initial SPL stack, so it will overwrite this data.
We still need the BROM code after running the SPL, so should leave that
area alone.
Interestingly this does not seem to have an adverse effect, I guess on
the "way out" (when we return to FEL after the SPL has run), this data
is not needed by the BROM, for just the trailing end of the USB operation.
However this is still wrong, and we should not clobber BROM data.
Lower the SPL stack address to be situated right below the swap buffers
we use in sunxi-fel: that should be out of the way of everyone else.
This obsoletes a previous commit (eb53e7743c8f) with the same name:
that one was changing the address in an *unused* macro in sunxi_common.h,
so the previous patch didn't have any effect at all.
Fixes: eb53e7743c8f ("sunxi: h616: lower SPL stack address to avoid BROM data") Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Sat, 25 Nov 2023 17:43:16 +0000 (17:43 +0000)]
sunxi: H616: OrangePi Zero 2: enable USB power supply
The OrangePi Zero 2 has a USB VBUS regulator, controlled by pin PC16.
This is correctly described in the DT, but the patches for supporting
this are still pending.
Meanwhile add our good old CONFIG_USB1_VBUS_PIN to the defconfig file,
to enable power on the USB port and allow using a USB flash drive, for
instance.
Fixes: 6acc5fa581b4 ("sunxi: H616: enable USB support for H616 boards") Reported-by: Mikhail Kalashnikov <iuncuim@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
William Zhang [Sat, 12 Aug 2023 02:03:19 +0000 (19:03 -0700)]
spi: bcm63xx-hsspi: Fix compiler warning
When build for arm64 target, comipler reports the following warning:
drivers/spi/bcm63xx_hsspi.c: In function ‘bcm63xx_hsspi_xfer_dummy_cs’:
include/linux/kernel.h:184:17: warning: comparison of distinct pointer
types lacks a cast
184 | (void) (&_min1 == &_min2); \
| ^~
drivers/spi/bcm63xx_hsspi.c:298:22: note: in expansion of macro ‘min’
298 | size_t curr_step = min(step_size, data_bytes);
This change fix this warning by casting the data_bytes to size_t.
riscv: andes: Fix enable register settings of PLICSW
On 32-core platform, hart31 gets stuck at secondary_hart_loop
as the corresponding enable bit is not set in enable_ipi().
We should program the next word (0x2f84) which is assigned
as the enable register of hart31. It should be done in the same
way when we invoke riscv_send_ipi() to trigger software interrupt
on hart31.
The following diagram shows the enable bits of the fixed PLICSW
scheme.
This patch includes some cleanups to macros/functions.
Fixes: ebf11273220a ("riscv: andes: Rearrange Andes PLICSW to single-bit-per-hart strategy") Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com> Reviewed-by: Randolph <randolph@andestech.com>
CONFIG_NVME=y without CONFIG_NVME_PCI=y does not provide working NVMe
support. Instead of implying CONFIG_NVME we must imply CONFIG_NVME_PCI
which will select CONFIG_NVME.
Fixes: e64db0d92e32 ("riscv: qemu: Enable e1000 and nvme support") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Chanho Park [Sun, 5 Nov 2023 23:13:16 +0000 (08:13 +0900)]
watchdog: Add StarFive Watchdog driver
Add to support StarFive watchdog driver. The driver is imported from
linux kernel's drivers/watchdog/starfive-wdt.c without jh7100 support
because there is no support of jh7100 SoC in u-boot yet.
Howver, this patch has been kept the variant coding style because JH7100
can be added later and have a consistency with the linux driver.
Signed-off-by: Chanho Park <chanho61.park@samsung.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Ilias Apalodimas [Tue, 28 Nov 2023 19:10:31 +0000 (21:10 +0200)]
efi_loader: Make DisconnectController follow the EFI spec
commit 239d59a65e20 ("efi_loader: reconnect drivers on failure")
tried to fix the UninstallProtocol interface which must reconnect
any controllers it disconnected by calling ConnectController()
in case of failure. However, the reconnect functionality was wired in
efi_disconnect_all_drivers() instead of efi_uninstall_protocol().
As a result some SCT tests started failing.
Specifically, BBTestOpenProtocolInterfaceTest333CheckPoint3() test
- Calls ConnectController for DriverImageHandle1
- Calls DisconnectController for DriverImageHandle1 which will
disconnect everything apart from TestProtocol4. That will remain
open on purpose.
- Calls ConnectController for DriverImageHandle2. TestProtocol4
which was explicitly preserved was installed wth BY_DRIVER attributes.
The new protocol will call DisconnectController since its attributes
are BY_DRIVER|EXCLUSIVE, but TestProtocol4 will not be removed. The
test expects EFI_ACCESS_DENIED which works fine.
The problem is that DisconnectController, will eventually call
EFI_DRIVER_BINDING_PROTOCOL.Stop(). But on the aforementioned test
this will call CloseProtocol -- the binding protocol is defined in
'DBindingDriver3.c' and the .Stop function uses CloseProtocol.
If that close protocol call fails with EFI_NOT_FOUND, the current code
will try to mistakenly reconnect all drivers and the subsequent tests
that rely on the device being disconnected will fail.
Move the reconnection in efi_uninstall_protocol() were it belongs.
Fixes: commit 239d59a65e20 ("efi_loader: reconnect drivers on failure") Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
efi_loader: create memory reservations in ACPI case
ACPI tables cannot convey memory reservations for ARM and RISC-V.
x86 uses the BIOS E820 table for this purpose. We cannot simply ignore the
device-tree when booting via ACPI. We have to assign EfiReservedMemory
according to the prior stage device-tree ($fdtaddr) or as fallback the
control device-tree ($fdtcontroladdr).
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Masahisa Kojima [Fri, 27 Oct 2023 07:43:26 +0000 (16:43 +0900)]
scripts/Makefile.lib: print error when no public key is specified
The current build system embeds the EFI Signature List(ESL)
into the dtb to be used in the EFI capsule authentication.
This ESL file is specified through the CONFIG_EFI_CAPSULE_ESL_FILE
Kconfig option. If CONFIG_EFI_CAPSULE_ESL_FILE is not specified,
U-boot build ends up with failure but the cause of failure is not
easily understandable. Current error message is as follows.
FATAL ERROR: Error reading file into data: Is a directoryCheck /home/ubuntu/src/ledge/u-boot/arch/arm/dts/.synquacer-sc2a11-developerbox.dtb.pre.tmp for errors
make[2]: *** [scripts/Makefile.lib:355: arch/arm/dts/synquacer-sc2a11-developerbox.dtb] Error 1
make[1]: *** [dts/Makefile:44: arch-dtbs] Error 2
make: *** [Makefile:1165: dts/dt.dtb] Error 2
make: *** Waiting for unfinished jobs....
This commit shows the error message that CONFIG_EFI_CAPSULE_ESL_FILE
must be specified when the EFI capsule authentication is enabled, then
terminate the build with error.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org> Reviewed-by: Weizhao Ouyang <o451686892@gmail.com>
Tom Rini [Tue, 21 Nov 2023 15:41:07 +0000 (10:41 -0500)]
doc: clang: Update and correct support notes
At this point, clang can be used on both 32bit and 64bit targets without
issue. Make note of logic we have that will inform clang of the
architecture to build for.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Chanho Park [Sun, 3 Dec 2023 08:30:40 +0000 (17:30 +0900)]
watchdog: Correct watchdog timeout print message
The wdt_start function takes timeout_ms as a parameter and starts the
watchdog with this value. However, when you output the message, it shows
the default timeout value for the watchdog device.
So this patch fixes that part to output the correct timeout value.
Before -->
StarFive # wdt start 3000
WDT: Started watchdog@13070000 without servicing (60s timeout)
After -->
StarFive # wdt start 3000
WDT: Started watchdog@13070000 without servicing (3s timeout)
Fixes: c2fd0ca1a822 ("watchdog: Integrate watchdog triggering into the cyclic framework") Signed-off-by: Chanho Park <chanho61.park@samsung.com> Reviewed-by: Stefan Roese <sr@denx.de>
Cong Dang [Mon, 19 Jun 2023 22:41:50 +0000 (00:41 +0200)]
ARM: dts: renesas: Disable RPC driver on R8A779G0 V4H White Hawk board
As requirement of CR side, QSPI Flash usage via RPC driver shall
be disabled and leaving the control of this module to CR side.
Perform DT modification to disable the RPC SPI.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Cong Dang <cong.dang.xn@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Do not modify defconfig, modify the DT instead, this way
the RPC SPI can be enabled without recompiling the U-Boot
itself. Update commit message accordingly.]
Use the phandle reference to &rpc node in arch/arm/dts/r8a779g0.dtsi
and remove properties which are already in arch/arm/dts/r8a779g0.dtsi.
No functional change and no resulting DT change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Compiling with CONFIG_USB_XHCI_PCI and CONFIG_PCI=n results in
usb/host/xhci-pci.c:48:(.text.xhci_pci_probe+0x44):
undefined reference to `dm_pci_write_config32
Add the missing Kconfig dependency.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Marek Vasut <marex@denx.de>
Hector Martin [Sun, 29 Oct 2023 07:23:30 +0000 (16:23 +0900)]
usb: storage: Use the correct CBW lengths
USB UFI uses fixed 12-byte commands (as does RBC, which is not
supported), but SCSI does not have this limitation. Use the correct
command block lengths depending on the subclass.
Signed-off-by: Hector Martin <marcan@marcan.st> Reviewed-by: Marek Vasut <marex@denx.de>
Hector Martin [Sun, 29 Oct 2023 06:37:43 +0000 (15:37 +0900)]
usb: xhci: Do not panic on event timeouts
Now that we always check the return value, just return NULL on timeouts.
We can still log the error since this is a problem, but it's not reason
to panic.
Signed-off-by: Hector Martin <marcan@marcan.st> Reviewed-by: Marek Vasut <marex@denx.de>
Hector Martin [Sun, 29 Oct 2023 06:37:41 +0000 (15:37 +0900)]
usb: xhci: Recover from halted bulk endpoints
There is currently no codepath to recover from this case. In principle
we could require that the upper layer do this explicitly, but let's just
do it in xHCI when the next bulk transfer is started, since that
reasonably implies whatever caused the problem has been dealt with.
Signed-off-by: Hector Martin <marcan@marcan.st> Reviewed-by: Marek Vasut <marex@denx.de>
Hector Martin [Sun, 29 Oct 2023 06:37:40 +0000 (15:37 +0900)]
usb: xhci: Allow context state errors when halting an endpoint
There is a race where an endpoint may halt by itself while we are trying
to halt it, which results in a context state error. See xHCI 4.6.9 which
mentions this case.
This also avoids BUGging when we attempt to stop an endpoint which was
already stopped to begin with, which is probably a bug elsewhere but
not a good reason to crash.
Signed-off-by: Hector Martin <marcan@marcan.st> Reviewed-by: Marek Vasut <marex@denx.de>
Hector Martin [Sun, 29 Oct 2023 06:37:39 +0000 (15:37 +0900)]
usb: xhci: Better error handling in abort_td()
If the xHC has a problem with our STOP ENDPOINT command, it is likely to
return a completion directly instead of first a transfer event for the
in-progress transfer. Handle that more gracefully.
We still BUG() on the error code, but at least we don't end up timing
out on the event and ending up with unexpected event errors.
Signed-off-by: Hector Martin <marcan@marcan.st> Reviewed-by: Marek Vasut <marex@denx.de>
Hector Martin [Sun, 29 Oct 2023 06:37:38 +0000 (15:37 +0900)]
usb: xhci: Guard all calls to xhci_wait_for_event
xhci_wait_for_event returns NULL on timeout, so the caller always has to
check for that. This addresses immediate explosions in this part
of the code when timeouts happen, but not the root cause for the
timeout.
Signed-off-by: Hector Martin <marcan@marcan.st> Reviewed-by: Marek Vasut <marex@denx.de>
projects / thirdparty / u-boot.git / log
