From db1de8d21fd7f115cc1a6274f031119c9f36eefd Mon Sep 17 00:00:00 2001 From: Fil Dunsky Date: Sun, 6 Jul 2025 12:08:27 +0300 Subject: [PATCH] mediatek: add Huasifei WH3000 Pro support **Huasifei WH3000 Pro** Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ with 5G modems module and PWM Fan. **Specifications** SoC: Filogic 820 MT7981A (1.3GHz) RAM: DDR4 1GB Flash: eMMC 8GB WiFi: 2.4GHz and 5GHz with 3 antennas Ethernet: 1x WAN (10/100/1000M) 1x LAN (10/100/1000/2500M) USB: 1x USB 3.0 port Two buttons: power/reset and mode (BTN_0) LEDS: blue, red, blue+red=pink UART: 3.3V, TX, RX, GND / 115200 8N1 **Installation via U-Boot rescue** 1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1 2. Connect to the WAN port and hold the reset button while booting the device. 3. Wait for the LED to blink 5 times, and release the reset button. 4. Open U-boot web page on your browser at http://192.168.1.1 5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade. 6. Wait for the router to flash the new firmware. 7. Wait for the router to reboot itself. **Installation via sysupgrade** Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings. **Installation via SSH** Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command: ``` sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-pro-squashfs-sysupgrade.bin ``` **Factory MAC** You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4` ``` dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C ``` Cherry-picked from https://github.com/coolsnowwolf/lede/commit/949d0bd77a2e97c2d982531f72b76c575fb28839 Fixed `green` to `blue` LED in dts, added `SUPPORTED_DEVICES += huasifei,fudy-pro` - to make sysupgrade compatible with factory QWRT/Lede fork firmware. Signed-off-by: Fil Dunsky Link: https://github.com/openwrt/openwrt/pull/19315 Signed-off-by: Hauke Mehrtens --- .../dts/mt7981b-huasifei-wh3000-pro.dts | 213 ++++++++++++++++++ .../filogic/base-files/etc/board.d/02_network | 3 +- .../base-files/etc/board.d/03_gpio_switches | 3 + .../base-files/lib/upgrade/platform.sh | 2 + target/linux/mediatek/image/filogic.mk | 13 ++ 5 files changed, 233 insertions(+), 1 deletion(-) create mode 100644 target/linux/mediatek/dts/mt7981b-huasifei-wh3000-pro.dts diff --git a/target/linux/mediatek/dts/mt7981b-huasifei-wh3000-pro.dts b/target/linux/mediatek/dts/mt7981b-huasifei-wh3000-pro.dts new file mode 100644 index 00000000000..b8a5a4cc350 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-huasifei-wh3000-pro.dts @@ -0,0 +1,213 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include +#include +#include + +#include "mt7981b.dtsi" + +/ { + model = "Huasifei WH3000 Pro"; + compatible = "huasifei,wh3000-pro", "mediatek,mt7981"; + + aliases { + serial0 = &uart0; + led-boot = &led_sys_red; + led-failsafe = &led_sys_red; + led-running = &led_sys_blue; + led-upgrade = &led_sys_blue; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " root=PARTLABEL=rootfs rootwait"; + }; + + gpio-export { + compatible = "gpio-export"; + + modem-power { + gpio-export,name = "modem_power"; + gpio-export,output = <0>; + gpios = <&pio 4 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + + mode { + label = "mode"; + linux,code = ; + linux,input-type = ; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led_sys_red: led-0 { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&pio 11 GPIO_ACTIVE_LOW>; + }; + + led_sys_blue: led-1 { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + phy-handle = <&phy1>; + + nvmem-cells = <&macaddr_factory_4 2>; + nvmem-cell-names = "mac-address"; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "gmii"; + phy-handle = <&int_gbe_phy>; + + nvmem-cells = <&macaddr_factory_4 3>; + nvmem-cell-names = "mac-address"; + }; +}; + +&mdio_bus { + phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <1>; + reset-assert-us = <100000>; + reset-deassert-us = <100000>; + reset-gpios = <&pio 39 GPIO_ACTIVE_LOW>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&pio>; + realtek,aldps-enable; + }; +}; + +&fan { + interrupt-parent = <&pio>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + pwms = <&pwm 1 40000 0>; + status = "okay"; +}; + +&mmc0 { + bus-width = <8>; + cap-mmc-highspeed; + max-frequency = <52000000>; + non-removable; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_default>; + pinctrl-1 = <&mmc0_pins_uhs>; + vmmc-supply = <®_3p3v>; + status = "okay"; + + card@0 { + compatible = "mmc-card"; + reg = <0>; + + block { + compatible = "block-device"; + + partitions { + block-partition-factory { + partname = "factory"; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1000>; + }; + + macaddr_factory_4: macaddr@4 { + compatible = "mac-base"; + reg = <0x4 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + }; + }; + }; +}; + +&pio { + mmc0_pins_default: mmc0-pins-default { + mux { + function = "flash"; + groups = "emmc_45"; + }; + }; + + mmc0_pins_uhs: mmc0-pins-uhs { + mux { + function = "flash"; + groups = "emmc_45"; + }; + }; + + pwm1_pins: pwm1-pins { + mux { + function = "pwm"; + groups = "pwm1_0"; + }; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm1_pins>; + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + nvmem-cells = <&eeprom_factory_0>; + nvmem-cell-names = "eeprom"; + status = "okay"; +}; + +&xhci { + status = "okay"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index ae99120e1a2..17fb2bddd1c 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -74,7 +74,8 @@ mediatek_setup_interfaces() ;; bananapi,bpi-r3-mini|\ edgecore,eap111|\ - huasifei,wh3000) + huasifei,wh3000|\ + huasifei,wh3000-pro) ucidef_set_interfaces_lan_wan eth0 eth1 ;; bananapi,bpi-r4) diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/03_gpio_switches b/target/linux/mediatek/filogic/base-files/etc/board.d/03_gpio_switches index 1fe74f2b6fd..e2fe814439d 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/03_gpio_switches +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/03_gpio_switches @@ -5,6 +5,9 @@ board_config_update board=$(board_name) case "$board" in +huasifei,wh3000-pro) + ucidef_add_gpio_switch "modem_power" "Modem power" "modem_power" "0" + ;; zbtlink,zbt-z8102ax|\ zbtlink,zbt-z8102ax-v2) ucidef_add_gpio_switch "5g1" "Power 1st modem" "5g1" "1" diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index bd7501d8daa..2a05b9b10c9 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -110,6 +110,7 @@ platform_do_upgrade() { glinet,gl-x3000|\ glinet,gl-xe3000|\ huasifei,wh3000|\ + huasifei,wh3000-pro|\ smartrg,sdg-8612|\ smartrg,sdg-8614|\ smartrg,sdg-8622|\ @@ -276,6 +277,7 @@ platform_copy_config() { glinet,gl-x3000|\ glinet,gl-xe3000|\ huasifei,wh3000|\ + huasifei,wh3000-pro|\ jdcloud,re-cp-03|\ nradio,c8-668gl|\ smartrg,sdg-8612|\ diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 14b8ecd02ae..65304632131 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -1088,6 +1088,19 @@ define Device/huasifei_wh3000 endef TARGET_DEVICES += huasifei_wh3000 +define Device/huasifei_wh3000-pro + DEVICE_VENDOR := Huasifei + DEVICE_MODEL := WH3000 Pro + DEVICE_DTS := mt7981b-huasifei-wh3000-pro + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-hwmon-pwmfan kmod-usb3 f2fsck mkf2fs + KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += huasifei_wh3000-pro + define Device/jcg_q30-pro DEVICE_VENDOR := JCG DEVICE_MODEL := Q30 PRO -- 2.47.2