From ff5e66a9208a0fcf20315faef8797d34dea7792d Mon Sep 17 00:00:00 2001 From: Mikhail Zhilkin Date: Sat, 20 Dec 2025 18:43:45 +0300 Subject: [PATCH] mediatek: add support for Routerich BE7200 This PR adds support for Routerich BE7200 router. Specification ------------- - SoC : MediaTek MT7987A Quad-core ARM Cortex-A53 2.0 GHz - RAM : 1024 MiB DDR4 - Flash : SPI-NAND 512 MiB (Giga Device) - WLAN : MediaTek MT7992E, WiFi 7 - 2.4 GHz : b/g/n/ax, MIMO 4x4 - 5 GHz : a/n/ac/ax, MIMO 4x4 - Ethernet : 10/100/1000 Mbps x3 (LAN, Airoha AN8855AE) 10/100/1000/2500 Mbps x1 (WAN, SoC internal phy) - USB : 3.0 x1 - Buttons : Mesh, Reset - LEDs : 1x Status (blue), gpio-controlled 1x WiFi (blue), gpio-controlled 1x mesh (blue), gpio-controlled 3x LAN activity (blue), gpio-controlled 1x WAN activity (blue), gpio-controlled 1x WAN no-link (red), gpio-controlled - Power : 12 VDC, 1.5 A Installation ------------ 1. Update stock firmware via the web interface (don't keep settings). Update U-Boot (optional) ------------------------ After installing OpenWrt, you may want to install opensource U-Boot. 1. Install kmod-mtd-rw: apk update && apk add kmod-mtd-rw 2. Unlock bootloader: insmod mtd-rw i_want_a_brick=1 mtd unlock BL2 mtd unlock FIP 3. Download and write open-source BL2 and FIP: cd /tmp wget https://.../openwrt-mediatek-filogic-routerich_be7200-preloader.bin wget https://.../openwrt-mediatek-filogic-routerich_be7200-bl31-uboot.fip mtd write /tmp/openwrt-mediatek-filogic-routerich_be7200-preloader.bin BL2 mtd write /tmp/openwrt-mediatek-filogic-routerich_be7200-bl31-uboot.fip FIP 4. Reboot the router. Return to stock --------------- 1. Update OpenWrt wirh the vendor's firmware (don't keep settings). Recovery (original U-Boot) ----------------------------- 1. Press Reset button and power on the router. After ~10 sec release the button; 2. Upload and flash squashfs-sysupgrade.itb image via the web interface. Recovery (open-source U-Boot) ----------------------------- 1. Place OpenWrt 'openwrt-mediatek-filogic-routerich_be7200-initramfs-recovery.itb' image on the tftp server (IP: 192.168.1.254) 2. Press Reset button and power on the router. After ~10 sec release the button. 3. Use OpenWrt initramfs system for recovery Recovery (full disaster) ------------------------ Use UART and mtk_uartboot tool. Link: https://github.com/981213/mtk_uartboot USB power control ----------------- Disable: echo disabled > /sys/devices/platform/usb-power/state Enable: echo enabled > /sys/devices/platform/usb-power/state UART ---- UART pins are silkscreened on the PCB. Don't connect Vcc. Serial connection parameters: 115200, 8n1, 3.3V MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | WAN | 24:0f:5e:xx:xx:30 | label | | LAN | 24:0f:5e:xx:xx:31 | label+1 | | WLAN 2g | 24:0f:5e:xx:xx:32 | label+2 | | WLAN 5g | 24:0f:5e:xx:xx:33 | label+3 | +---------+-------------------+-----------+ The WLAN 2g MAC was found in 'Factory', 0x4 Signed-off-by: Mikhail Zhilkin Link: https://github.com/openwrt/openwrt/pull/21235 Signed-off-by: Hauke Mehrtens --- package/boot/uboot-mediatek/Makefile | 12 + .../patches/467-add-routerich-be7200.patch | 373 ++++++++++++++ .../uboot-envtools/files/mediatek_filogic | 1 + .../mediatek/dts/mt7987a-routerich-be7200.dts | 480 ++++++++++++++++++ .../filogic/base-files/etc/board.d/01_leds | 8 + .../filogic/base-files/etc/board.d/02_network | 1 + .../base-files/lib/upgrade/platform.sh | 1 + target/linux/mediatek/image/filogic.mk | 28 + 8 files changed, 904 insertions(+) create mode 100644 package/boot/uboot-mediatek/patches/467-add-routerich-be7200.patch create mode 100644 target/linux/mediatek/dts/mt7987a-routerich-be7200.dts diff --git a/package/boot/uboot-mediatek/Makefile b/package/boot/uboot-mediatek/Makefile index fc10c074774..78932ea46f2 100644 --- a/package/boot/uboot-mediatek/Makefile +++ b/package/boot/uboot-mediatek/Makefile @@ -881,6 +881,17 @@ define U-Boot/mt7987_bananapi_bpi-r4-lite-nor FIP_COMPRESS:=1 endef +define U-Boot/mt7987_routerich_be7200 + NAME:=Routerich BE7200 + BUILD_SUBTARGET:=filogic + BUILD_DEVICES:=routerich_be7200 + UBOOT_CONFIG:=mt7987a_routerich_be7200 + UBOOT_IMAGE:=u-boot.fip + BL2_BOOTDEV:=spim-nand0 + BL2_SOC:=mt7987 + DEPENDS:=+trusted-firmware-a-mt7987-spim-nand0 +endef + define U-Boot/mt7988_arcadyan_mozart NAME:=Arcadyan Mozart BUILD_SUBTARGET:=filogic @@ -1152,6 +1163,7 @@ UBOOT_TARGETS := \ mt7987_rfb-emmc \ mt7987_rfb-sd \ mt7987_rfb-spim-nand \ + mt7987_routerich_be7200 \ mt7988_arcadyan_mozart \ mt7988_asus_zenwifi-bt8 \ mt7988_bananapi_bpi-r4-emmc \ diff --git a/package/boot/uboot-mediatek/patches/467-add-routerich-be7200.patch b/package/boot/uboot-mediatek/patches/467-add-routerich-be7200.patch new file mode 100644 index 00000000000..9a1353b51cf --- /dev/null +++ b/package/boot/uboot-mediatek/patches/467-add-routerich-be7200.patch @@ -0,0 +1,373 @@ +--- /dev/null ++++ b/configs/mt7987a_routerich_be7200_defconfig +@@ -0,0 +1,133 @@ ++CONFIG_ARM=y ++CONFIG_SYS_HAS_NONCACHED_MEMORY=y ++CONFIG_POSITION_INDEPENDENT=y ++CONFIG_ARCH_MEDIATEK=y ++CONFIG_TEXT_BASE=0x41e00000 ++CONFIG_SYS_MALLOC_F_LEN=0x4000 ++CONFIG_NR_DRAM_BANKS=1 ++CONFIG_DEFAULT_DEVICE_TREE="mt7987a-routerich_be7200" ++CONFIG_OF_LIBFDT_OVERLAY=y ++CONFIG_TARGET_MT7987=y ++CONFIG_CPU_ARMV8=y ++CONFIG_SYS_BOOTM_LEN=0x6000000 ++CONFIG_SYS_LOAD_ADDR=0x48000000 ++CONFIG_PRE_CON_BUF_ADDR=0x4007ef00 ++CONFIG_DEBUG_UART_BASE=0x11000000 ++CONFIG_DEBUG_UART_CLOCK=40000000 ++CONFIG_DEBUG_UART=y ++CONFIG_FIT=y ++CONFIG_AUTOBOOT_MENU_SHOW=y ++CONFIG_DEFAULT_FDT_FILE="mt7987a-routerich_be7200" ++CONFIG_SYS_CBSIZE=512 ++CONFIG_SYS_PBSIZE=1049 ++CONFIG_LOGLEVEL=7 ++CONFIG_PRE_CONSOLE_BUFFER=y ++CONFIG_LOG=y ++# CONFIG_BOARD_INIT is not set ++CONFIG_BOARD_LATE_INIT=y ++CONFIG_HUSH_PARSER=y ++CONFIG_SYS_PROMPT="MT7987> " ++# CONFIG_BOOTM_NETBSD is not set ++# CONFIG_BOOTM_PLAN9 is not set ++# CONFIG_BOOTM_RTEMS is not set ++# CONFIG_BOOTM_VXWORKS is not set ++# CONFIG_CMD_BOOTEFI_BOOTMGR is not set ++CONFIG_CMD_LICENSE=y ++CONFIG_CMD_BOOTMENU=y ++CONFIG_CMD_ASKENV=y ++CONFIG_CMD_ERASEENV=y ++CONFIG_CMD_ENV_FLAGS=y ++CONFIG_CMD_STRINGS=y ++CONFIG_CMD_CPU=y ++CONFIG_CMD_DM=y ++CONFIG_CMD_GPIO=y ++CONFIG_CMD_PWM=y ++CONFIG_CMD_GPT=y ++CONFIG_CMD_I2C=y ++CONFIG_CMD_MMC=y ++CONFIG_CMD_MTD=y ++CONFIG_CMD_PART=y ++CONFIG_CMD_PCI=y ++CONFIG_CMD_USB=y ++CONFIG_CMD_TFTPSRV=y ++CONFIG_CMD_RARP=y ++CONFIG_CMD_CDP=y ++CONFIG_CMD_SNTP=y ++CONFIG_CMD_LINK_LOCAL=y ++CONFIG_CMD_DHCP=y ++CONFIG_CMD_DNS=y ++CONFIG_CMD_PING=y ++CONFIG_CMD_PXE=y ++CONFIG_CMD_CACHE=y ++CONFIG_CMD_PSTORE=y ++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000 ++CONFIG_CMD_UUID=y ++CONFIG_CMD_HASH=y ++CONFIG_CMD_SMC=y ++CONFIG_CMD_EXT4=y ++CONFIG_CMD_FAT=y ++CONFIG_CMD_FS_GENERIC=y ++CONFIG_CMD_FS_UUID=y ++CONFIG_CMD_SF_TEST=y ++CONFIG_CMD_UBI=y ++CONFIG_CMD_UBI_RENAME=y ++# CONFIG_CMD_XIMG is not set ++CONFIG_ENV_OVERWRITE=y ++CONFIG_ENV_IS_IN_UBI=y ++CONFIG_ENV_REDUNDANT=y ++CONFIG_ENV_UBI_PART="ubi" ++CONFIG_ENV_UBI_VOLUME="ubootenv" ++CONFIG_ENV_UBI_VOLUME_REDUND="ubootenv2" ++CONFIG_ENV_USE_DEFAULT_ENV_TEXT_FILE=y ++CONFIG_ENV_DEFAULT_ENV_TEXT_FILE="defenvs/routerich_be7200_env" ++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y ++CONFIG_VERSION_VARIABLE=y ++CONFIG_NETCONSOLE=y ++CONFIG_USE_IPADDR=y ++CONFIG_IPADDR="192.168.1.1" ++CONFIG_USE_NETMASK=y ++CONFIG_NETMASK="255.255.255.0" ++CONFIG_USE_SERVERIP=y ++CONFIG_SERVERIP="192.168.1.254" ++CONFIG_NET_RANDOM_ETHADDR=y ++CONFIG_BUTTON=y ++CONFIG_BUTTON_GPIO=y ++CONFIG_CLK=y ++CONFIG_DM_I2C=y ++CONFIG_SYS_I2C_MTK=y ++CONFIG_LED=y ++CONFIG_LED_BLINK=y ++CONFIG_LED_GPIO=y ++# CONFIG_MMC is not set ++CONFIG_MTD=y ++CONFIG_DM_MTD=y ++CONFIG_MTD_SPI_NAND=y ++CONFIG_MTD_UBI_FASTMAP=y ++CONFIG_PHY_ETHERNET_ID=y ++CONFIG_PHY_FIXED=y ++CONFIG_MEDIATEK_ETH=y ++CONFIG_PHY=y ++CONFIG_PHY_MTK_TPHY=y ++CONFIG_PINCTRL=y ++CONFIG_PINCONF=y ++CONFIG_PINCTRL_MT7987=y ++CONFIG_POWER_DOMAIN=y ++CONFIG_MTK_POWER_DOMAIN=y ++CONFIG_DM_REGULATOR=y ++CONFIG_DM_REGULATOR_FIXED=y ++CONFIG_DM_REGULATOR_GPIO=y ++CONFIG_DM_PWM=y ++CONFIG_PWM_MTK=y ++CONFIG_SCSI=y ++CONFIG_DM_SERIAL=y ++CONFIG_SERIAL_RX_BUFFER=y ++CONFIG_MTK_SERIAL=y ++CONFIG_SPI=y ++CONFIG_DM_SPI=y ++CONFIG_MTK_SPIM=y ++CONFIG_USB=y ++CONFIG_USB_XHCI_HCD=y ++CONFIG_USB_XHCI_MTK=y ++CONFIG_USB_STORAGE=y ++CONFIG_ZSTD=y ++CONFIG_HEXDUMP=y +--- /dev/null ++++ b/defenvs/routerich_be7200_env +@@ -0,0 +1,57 @@ ++ipaddr=192.168.1.1 ++serverip=192.168.1.254 ++loadaddr=0x48000000 ++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0 ++bootcmd=run check_buttons ; if pstore check ; then run boot_recovery ; else run boot_ubi ; fi ++bootconf=config-1 ++bootdelay=0 ++bootfile=openwrt-mediatek-filogic-routerich_be7200-initramfs-recovery.itb ++bootfile_bl2=openwrt-mediatek-filogic-routerich_be7200-preloader.bin ++bootfile_fip=openwrt-mediatek-filogic-routerich_be7200-bl31-uboot.fip ++bootfile_upg=openwrt-mediatek-filogic-routerich_be7200-squashfs-sysupgrade.itb ++bootled_status=blue:status ++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60 ++bootmenu_default=0 ++bootmenu_delay=0 ++bootmenu_title= ( ( ( OpenWrt ) ) ) ++bootmenu_0=Initialize environment.=run _firstboot ++bootmenu_0d=Run default boot command.=run boot_default ++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return ++bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return ++bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return ++bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return ++bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return ++bootmenu_6=Load BL31+U-Boot FIP via TFTP then write to NAND.=run boot_tftp_write_fip ; run bootmenu_confirm_return ++bootmenu_7=Load BL2 preloader via TFTP then write to NAND.=run boot_tftp_write_bl2 ; run bootmenu_confirm_return ++bootmenu_8=Reboot.=reset ++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset ++boot_first=if button reset ; then led $bootled_status on ; run boot_default ; fi ; bootmenu ++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever ++boot_production=led $bootled_status on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led bootled_status off ++boot_recovery=led $bootled_status on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led bootled_status off ++boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever ++boot_tftp_forever=led $bootled_status on ; while true ; do run boot_tftp ; sleep 1 ; done ++boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi ++boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi ++boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf ++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run mtd_write_fip && run reset_factory ++boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run mtd_write_bl2 ++check_buttons=if button reset ; then run boot_tftp ; fi ++ethaddr_factory=mtd read Factory 0x40080000 0x0 0x20000 && env readmem -b ethaddr 0x40080004 0x6 ; setenv ethaddr_factory ++part_default=production ++part_recovery=recovery ++reset_factory=ubi part ubi ; mw $loadaddr 0x0 0x800 ; ubi write $loadaddr ubootenv 0x800 ; ubi write $loadaddr ubootenv2 0x800 ++mtd_write_fip=mtd erase FIP && mtd write FIP $loadaddr ++mtd_write_bl2=mtd erase BL2 && mtd write BL2 $loadaddr ++ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic || run ubi_format ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic || run ubi_format ++ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset ++ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi ++ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs ++ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery ++ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data ++ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic && ubi write $loadaddr fit $filesize ++ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic && ubi write $loadaddr recovery $filesize ++_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv ++_firstboot=setenv _firstboot ; run ethaddr_factory ; run _switch_to_menu ; run _init_env ; run boot_first ++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title ++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title $ver" +--- /dev/null ++++ b/arch/arm/dts/mt7987a-routerich_be7200.dts +@@ -0,0 +1,77 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * Copyright (c) 2025 ++ * Author: Mikhail Zhilkin ++ */ ++ ++/dts-v1/; ++#include "mt7987a.dtsi" ++#include ++ ++/ { ++ model = "Routerich BE7200"; ++ compatible = "routerich,be7200", ++ "mediatek,mt7987"; ++ ++ gpio-keys { ++ compatible = "gpio-keys"; ++ ++ button-0 { ++ label = "mesh"; ++ linux,code = ; ++ gpios = <&pio 0 GPIO_ACTIVE_LOW>; ++ debounce-interval = <10>; ++ }; ++ ++ button-1 { ++ label = "reset"; ++ linux,code = ; ++ gpios = <&pio 1 GPIO_ACTIVE_LOW>; ++ debounce-interval = <10>; ++ }; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ ++ led-0 { ++ label = "blue:status"; ++ gpios = <&pio 4 GPIO_ACTIVE_LOW>; ++ }; ++ ++ led-1 { ++ label = "blue:wlan5g"; ++ gpios = <&pio 5 GPIO_ACTIVE_LOW>; ++ }; ++ ++ led-2 { ++ label = "blue:mesh"; ++ gpios = <&pio 7 GPIO_ACTIVE_LOW>; ++ }; ++ ++ led-3 { ++ label = "red:wan"; ++ gpios = <&pio 8 GPIO_ACTIVE_LOW>; ++ }; ++ ++ led-4 { ++ label = "blue:wan"; ++ gpios = <&pio 9 GPIO_ACTIVE_LOW>; ++ }; ++ ++ led-5 { ++ label = "blue:lan3"; ++ gpios = <&pio 10 GPIO_ACTIVE_LOW>; ++ }; ++ ++ led-6 { ++ label = "blue:lan2"; ++ gpios = <&pio 11 GPIO_ACTIVE_LOW>; ++ }; ++ ++ led-7 { ++ label = "blue:lan1"; ++ gpios = <&pio 12 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++}; +--- a/arch/arm/dts/Makefile ++++ b/arch/arm/dts/Makefile +@@ -1138,6 +1138,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \ + mt7986b-emmc-rfb.dtb \ + mt7987a-emmc-rfb.dtb \ + mt7987a-rfb.dtb \ ++ mt7987a-routerich_be7200.dtb \ + mt7987a-sd-rfb.dtb \ + mt7988-rfb.dtb \ + mt7988-sd-rfb.dtb \ +--- /dev/null ++++ b/arch/arm/dts/mt7987a-routerich_be7200-u-boot.dtsi +@@ -0,0 +1,84 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * Copyright (c) 2025 ++ * Author: Mikhail Zhilkin ++ */ ++ ++#include "mt7987a-u-boot.dtsi" ++#include "mt7987-netsys-u-boot.dtsi" ++ ++/ { ++ model = "Routerich BE7200"; ++ compatible = "routerich,be7200", ++ "mediatek,mt7987"; ++}; ++ ++ð0 { ++ status = "okay"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&mdio0_pins>; ++ phy-mode = "2500base-x"; ++ mediatek,switch = "auto"; ++ reset-gpios = <&pio 42 GPIO_ACTIVE_HIGH>; ++ ++ fixed-link { ++ speed = <2500>; ++ full-duplex; ++ pause; ++ }; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_flash_pins>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ must_tx; ++ enhance_timing; ++ dma_ext; ++ ipm_design; ++ support_quad; ++ tick_dly = <2>; ++ sample_sel = <0>; ++ ++ spi_nand@0 { ++ compatible = "spi-nand"; ++ reg = <0>; ++ spi-max-frequency = <52000000>; ++ spi-rx-bus-width = <4>; ++ spi-tx-bus-width = <4>; ++ ++ partitions { ++ compatible = "fixed-partitions"; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ partition@0 { ++ label = "BL2"; ++ reg = <0x0 0x100000>; ++ }; ++ ++ partition@100000 { ++ label = "u-boot-env (unused)"; ++ reg = <0x100000 0x80000>; ++ }; ++ ++ partition@180000 { ++ label = "Factory"; ++ reg = <0x180000 0x400000>; ++ }; ++ ++ partition@580000 { ++ label = "FIP"; ++ reg = <0x580000 0x200000>; ++ }; ++ ++ partition@780000 { ++ label = "ubi"; ++ reg = <0x780000 0x1f880000>; ++ compatible = "linux,ubi"; ++ }; ++ }; ++ }; ++}; diff --git a/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic index deffb4bffd3..5972233bae4 100644 --- a/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic @@ -42,6 +42,7 @@ nokia,ea0326gmp|\ openwrt,one|\ qihoo,360t7|\ routerich,ax3000-ubootmod|\ +routerich,be7200|\ snr,snr-cpe-ax2|\ tplink,tl-xdr4288|\ tplink,tl-xdr6086|\ diff --git a/target/linux/mediatek/dts/mt7987a-routerich-be7200.dts b/target/linux/mediatek/dts/mt7987a-routerich-be7200.dts new file mode 100644 index 00000000000..adda834ab10 --- /dev/null +++ b/target/linux/mediatek/dts/mt7987a-routerich-be7200.dts @@ -0,0 +1,480 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Author: Mikhail Zhilkin + */ + +/dts-v1/; +#include "mt7987a.dtsi" +#include +#include + +/ { + model = "Routerich BE7200"; + compatible = "routerich,be7200", + "mediatek,mt7987a", + "mediatek,mt7987"; + + aliases { + label-mac-device = &gmac1; + + led-boot = &led_status_blue; + led-failsafe = &led_status_blue; + led-running = &led_status_blue; + led-upgrade = &led_status_blue; + + serial0 = &uart0; + }; + + chosen { + bootargs = "console=ttyS0,115200n1 \ + earlycon=uart8250,mmio32,0x11000000 \ + pci=pcie_bus_perf"; + rootdisk = <&ubi_fit>; + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + button-0 { + label = "mesh"; + /* Reassigned to RF_KILL */ + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + debounce-interval = <10>; + }; + + button-1 { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + debounce-interval = <10>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led_status_blue: led-0 { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&pio 4 GPIO_ACTIVE_LOW>; + }; + + led-1 { + color = ; + function = LED_FUNCTION_WLAN_5GHZ; + gpios = <&pio 5 GPIO_ACTIVE_LOW>; + }; + + led-2 { + color = ; + function = "mesh"; + gpios = <&pio 7 GPIO_ACTIVE_LOW>; + }; + + led-3 { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&pio 8 GPIO_ACTIVE_HIGH>; + }; + + led-4 { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + led-5 { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <3>; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + + led-6 { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + gpios = <&pio 11 GPIO_ACTIVE_LOW>; + }; + + led-7 { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + gpios = <&pio 12 GPIO_ACTIVE_LOW>; + }; + }; + + memory@40000000 { + reg = <0x0 0x40000000 0x0 0x40000000>; + device_type = "memory"; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + regulator-name = "fixed-3.3V"; + }; + + reg_usb_5v: regulator-usb-5v { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&pio 14 GPIO_ACTIVE_HIGH>; + regulator-boot-on; + regulator-max-microvolt = <5000000>; + regulator-min-microvolt = <5000000>; + regulator-name = "usb-5v"; + }; + + usb-power { + compatible = "regulator-output"; + vout-supply = <®_usb_5v>; + }; +}; + +&gmac0 { + phy-mode = "2500base-x"; + status = "okay"; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_factory_4 (-1)>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; +}; + +&gmac1 { + openwrt,netdev-name = "wan"; + phy-mode = "internal"; + phy-handle = <&phy15>; + status = "okay"; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_factory_4 (-2)>; +}; + +&mdio { + an8855: mfd@1 { + compatible = "airoha,an8855-mfd"; + reg = <1>; + }; + + phy15: phy@15 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <15>; + + pinctrl-0 = <&i2p5gbe_led0_pins>; + pinctrl-names = "i2p5gbe-led"; + }; +}; + +&an8855 { + efuse { + compatible = "airoha,an8855-efuse"; + #nvmem-cell-cells = <0>; + + nvmem-layout { + compatible = "fixed-layout"; + + #address-cells = <1>; + #size-cells = <1>; + + shift_sel_port0_tx_a: shift-sel-port0-tx-a@c { + reg = <0xc 0x4>; + }; + + shift_sel_port0_tx_b: shift-sel-port0-tx-b@10 { + reg = <0x10 0x4>; + }; + + shift_sel_port0_tx_c: shift-sel-port0-tx-c@14 { + reg = <0x14 0x4>; + }; + + shift_sel_port0_tx_d: shift-sel-port0-tx-d@18 { + reg = <0x18 0x4>; + }; + + shift_sel_port1_tx_a: shift-sel-port1-tx-a@1c { + reg = <0x1c 0x4>; + }; + + shift_sel_port1_tx_b: shift-sel-port1-tx-b@20 { + reg = <0x20 0x4>; + }; + + shift_sel_port1_tx_c: shift-sel-port1-tx-c@24 { + reg = <0x24 0x4>; + }; + + shift_sel_port1_tx_d: shift-sel-port1-tx-d@28 { + reg = <0x28 0x4>; + }; + + shift_sel_port2_tx_a: shift-sel-port2-tx-a@2c { + reg = <0x2c 0x4>; + }; + + shift_sel_port2_tx_b: shift-sel-port2-tx-b@30 { + reg = <0x30 0x4>; + }; + + shift_sel_port2_tx_c: shift-sel-port2-tx-c@34 { + reg = <0x34 0x4>; + }; + + shift_sel_port2_tx_d: shift-sel-port2-tx-d@38 { + reg = <0x38 0x4>; + }; + }; + }; + + ethernet-switch { + compatible = "airoha,an8855-switch"; + reset-gpios = <&pio 42 GPIO_ACTIVE_HIGH>; + airoha,ext-surge; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + phy-mode = "internal"; + phy-handle = <&internal_phy1>; + }; + + port@1 { + reg = <1>; + label = "lan2"; + phy-mode = "internal"; + phy-handle = <&internal_phy2>; + }; + + port@2 { + reg = <2>; + label = "lan3"; + phy-mode = "internal"; + phy-handle = <&internal_phy3>; + }; + + port@5 { + reg = <5>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + + mdio { + compatible = "airoha,an8855-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + internal_phy1: phy@1 { + reg = <1>; + + nvmem-cells = <&shift_sel_port0_tx_a>, + <&shift_sel_port0_tx_b>, + <&shift_sel_port0_tx_c>, + <&shift_sel_port0_tx_d>; + nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d"; + }; + + internal_phy2: phy@2 { + reg = <2>; + + nvmem-cells = <&shift_sel_port1_tx_a>, + <&shift_sel_port1_tx_b>, + <&shift_sel_port1_tx_c>, + <&shift_sel_port1_tx_d>; + nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d"; + }; + + internal_phy3: phy@3 { + reg = <3>; + + nvmem-cells = <&shift_sel_port2_tx_a>, + <&shift_sel_port2_tx_b>, + <&shift_sel_port2_tx_c>, + <&shift_sel_port2_tx_d>; + nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d"; + }; + }; +}; + +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie0_pins>; + reset-gpios = <&pio 35 GPIO_ACTIVE_LOW>; + status = "okay"; + + pcie@0,0 { + reg = <0x0000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + + mt7992@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + + nvmem-cells = <&eeprom_factory_0>; + nvmem-cell-names = "eeprom"; + + #address-cells = <1>; + #size-cells = <0>; + + ieee80211-freq-limit = <2400000 2500000>, + <5170000 5835000>; + + band@0 { + reg = <0>; + nvmem-cells = <&macaddr_factory_4 (0)>; + nvmem-cell-names = "mac-address"; + }; + + band@1 { + reg = <1>; + nvmem-cells = <&macaddr_factory_4 (1)>; + nvmem-cell-names = "mac-address"; + }; + }; + }; +}; + +&pcie1 { + status = "disabled"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + flash@0 { + compatible = "spi-nand"; + reg = <0>; + + spi-cal-enable; + spi-cal-mode = "read-data"; + spi-cal-datalen = <7>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>; + spi-cal-addrlen = <5>; + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + + spi-max-frequency = <52000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env (stock bootloader)"; + reg = <0x100000 0x80000>; + read-only; + }; + + partition@180000 { + label = "Factory"; + reg = <0x180000 0x400000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1e00>; + }; + + macaddr_factory_4: macaddr@4 { + compatible = "mac-base"; + reg = <0x4 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@580000 { + label = "FIP"; + reg = <0x580000 0x200000>; + read-only; + }; + + partition@780000 { + label = "ubi"; + reg = <0x780000 0x1f880000>; + compatible = "linux,ubi"; + + volumes { + ubi_env: ubi-volume-ubootenv { + volname = "ubootenv"; + }; + + ubi_env2: ubi-volume-ubootenv2 { + volname = "ubootenv2"; + }; + + ubi_fit: ubi-volume-fit { + volname = "fit"; + }; + }; + }; + }; + }; +}; + +&ssusb { + status = "okay"; + + vusb33-supply = <®_3p3v>; + vbus-supply = <®_usb_5v>; +}; + +&tphyu3port0 { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; + +&ubi_env { + nvmem-layout { + compatible = "u-boot,env-redundant-bool-layout"; + }; +}; + +&ubi_env2 { + nvmem-layout { + compatible = "u-boot,env-redundant-bool-layout"; + }; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index 324f478f5ce..b7aef8f43a6 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -205,6 +205,14 @@ routerich,ax3000-v1) ucidef_set_led_netdev "wan" "wan" "blue:wan" "eth1" "link tx rx" ucidef_set_led_netdev "wan-off" "wan-off" "red:wan" "eth1" "link" ;; +routerich,be7200) + ucidef_set_led_netdev "lan-1" "lan-1" "blue:lan-1" "lan1" "link tx rx" + ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-2" "lan2" "link tx rx" + ucidef_set_led_netdev "lan-3" "lan-3" "blue:lan-3" "lan3" "link tx rx" + ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" "link tx rx" + ucidef_set_led_netdev "wan-off" "wan-off" "red:wan" "wan" "link" + ucidef_set_led_netdev "wlan5g" "wlan-5ghz" "blue:wlan-5ghz" "phy0.1-ap0" "link tx rx" + ;; smartrg,sdg-8612) ucidef_set_led_netdev "lan4" "LAN4" "mdio-bus:05:amber:lan" "lan4" "link_10 link_100" ucidef_set_led_netdev "lan4" "LAN4" "mdio-bus:05:green:lan-0" "lan4" "link_1000" diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index cb35353f3a1..c465a970223 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -56,6 +56,7 @@ mediatek_setup_interfaces() qihoo,360t7|\ routerich,ax3000|\ routerich,ax3000-ubootmod|\ + routerich,be7200|\ tenbay,wr3000k) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan ;; diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index 074fe3ee8e1..94a8df37cda 100644 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -109,6 +109,7 @@ platform_do_upgrade() { netcore,n60-pro|\ qihoo,360t7|\ routerich,ax3000-ubootmod|\ + routerich,be7200|\ snr,snr-cpe-ax2|\ tplink,tl-xdr4288|\ tplink,tl-xdr6086|\ diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 77172fe560f..b395f5f907f 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -2462,6 +2462,34 @@ define Device/routerich_ax3000-v1 endef TARGET_DEVICES += routerich_ax3000-v1 +define Device/routerich_be7200 + DEVICE_VENDOR := Routerich + DEVICE_MODEL := BE7200 + DEVICE_DTS := mt7987a-routerich-be7200 + DEVICE_DTS_DIR := ../dts + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_IN_UBI := 1 + UBOOTENV_IN_UBI := 1 + IMAGES := sysupgrade.itb + KERNEL_INITRAMFS_SUFFIX := -recovery.itb + KERNEL_LOADADDR := 0x40000000 + KERNEL := kernel-bin | gzip + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | \ + pad-to 64k + IMAGE/sysupgrade.itb := append-kernel | \ + fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-with-rootfs | \ + pad-rootfs | append-metadata + DEVICE_PACKAGES := mt7987-2p5g-phy-firmware kmod-mt7992-firmware | \ + kmod-regulator-userspace-consumer kmod-usb3 + ARTIFACTS := preloader.bin bl31-uboot.fip + ARTIFACT/preloader.bin := mt7987-bl2 spim-nand0 + ARTIFACT/bl31-uboot.fip := mt7987-bl31-uboot routerich_be7200 +endef +TARGET_DEVICES += routerich_be7200 + define Device/ruijie_rg-x60-pro DEVICE_VENDOR := Ruijie DEVICE_MODEL := RG-X60 Pro -- 2.47.3