From 658e4adca4b69e6ef18601ceb0fbae0a74f2b653 Mon Sep 17 00:00:00 2001 From: Fil Dunsky Date: Sun, 1 Feb 2026 12:33:53 +0300 Subject: [PATCH] mediatek: filogic: add support for Bazis AX3000WM - SoC: MediaTek MT7981B - CPU: 2x 1.3 GHz Cortex-A53 - Flash: 128 MiB SPI NAND (Winbond W25N01GV) - RAM: 256 MiB (Nanya NT5CC128M16JR-EK) - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax) - Ethernet: 1x 10/100/1000/2500 Mbps MaxLinear GPY211C WAN, 1x10/100/1000 Mbps MT7981 LAN - USB 3.0 port - 2x buttons: Reset, Mesh - 3x LEDs on top panel (red, green, blue) - 3x PHY port LEDs (1 amber, 2 green) - Board version: WD830M V2.0 - Power: 5 VDC, 3 A UART: internal test points, 3V3 115200 8N1 (RX, TX, GND) Interface MAC Algorithm LAN (label) 1c:bf:ce:xx:xx:x1 0x4 WAN 1c:bf:ce:xx:xx:x2 0xa WLAN 2.4G 1c:bf:ce:xx:xx:x3 0x2a WLAN 5G 1c:bf:ce:xx:xx:x4 0x24 At the moment installation is possible via UART only since SSH root is password protected. Set a static ip on the ethernet interface of your PC: (ip address: 192.168.1.2, subnet mask:255.255.255.0). Boot into initramfs via TFTP: ``` setenv serverip 192.168.1.2 tftpboot 0x46000000 openwrt-mediatek-filogic-bazis_ax3000wm-initramfs-recovery.itb bootm 0x46000000 ``` Install kmod-mtd-rw and activate it: ``` apk update && apk add kmod-mtd-rw insmod mtd-rw i_want_a_brick=1 ``` Upload to the router and write OpenWrt BL2 and FIP bootloader: ``` mtd write openwrt-mediatek-filogic-bazis_ax3000wm-preloader.bin BL2 mtd write openwrt-mediatek-filogic-bazis_ax3000wm-bl31-uboot.fip FIP ``` Prepare ubi partition: ``` ubidetach -p /dev/mtd4 ubiformat /dev/mtd4 -y ubiattach -p /dev/mtd4 ``` Upgrade via luci web interface with sysupgrade file or by issuing a command: ``` sysupgrade -n openwrt-mediatek-filogic-bazis_ax3000wm-squashfs-sysupgrade.itb ``` Signed-off-by: Fil Dunsky Link: https://github.com/openwrt/openwrt/pull/21813 Signed-off-by: Hauke Mehrtens --- package/boot/uboot-mediatek/Makefile | 13 + .../patches/502-add-bazis-ax3000wm.patch | 329 ++++++++++++++++++ .../lib/preinit/05_set_preinit_iface | 1 + .../mediatek/dts/mt7981b-bazis-ax3000wm.dts | 297 ++++++++++++++++ .../filogic/base-files/etc/board.d/01_leds | 6 + .../filogic/base-files/etc/board.d/02_network | 1 + .../base-files/lib/upgrade/platform.sh | 2 + target/linux/mediatek/image/filogic.mk | 25 ++ 8 files changed, 674 insertions(+) create mode 100644 package/boot/uboot-mediatek/patches/502-add-bazis-ax3000wm.patch create mode 100644 target/linux/mediatek/dts/mt7981b-bazis-ax3000wm.dts diff --git a/package/boot/uboot-mediatek/Makefile b/package/boot/uboot-mediatek/Makefile index 383fd222789..1cb38d42144 100644 --- a/package/boot/uboot-mediatek/Makefile +++ b/package/boot/uboot-mediatek/Makefile @@ -231,6 +231,18 @@ define U-Boot/mt7981_abt_asr3000 DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr3 endef +define U-Boot/mt7981_bazis-ax3000wm + NAME:=BAZIS AX3000WM + BUILD_SUBTARGET:=filogic + BUILD_DEVICES:=bazis_ax3000wm + UBOOT_CONFIG:=mt7981_bazis_ax3000wm + UBOOT_IMAGE:=u-boot.fip + BL2_BOOTDEV:=spim-nand + BL2_SOC:=mt7981 + BL2_DDRTYPE:=ddr3 + DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr3 +endef + define U-Boot/mt7981_cmcc_a10 NAME:=CMCC A10 BUILD_SUBTARGET:=filogic @@ -1106,6 +1118,7 @@ UBOOT_TARGETS := \ mt7628_ravpower_rp-wd009 \ mt7629_rfb \ mt7981_abt_asr3000 \ + mt7981_bazis-ax3000wm \ mt7981_cmcc_a10 \ mt7981_cmcc_rax3000m-emmc-ddr3 \ mt7981_cmcc_rax3000m-emmc-ddr4 \ diff --git a/package/boot/uboot-mediatek/patches/502-add-bazis-ax3000wm.patch b/package/boot/uboot-mediatek/patches/502-add-bazis-ax3000wm.patch new file mode 100644 index 00000000000..63b5a6765af --- /dev/null +++ b/package/boot/uboot-mediatek/patches/502-add-bazis-ax3000wm.patch @@ -0,0 +1,329 @@ +--- /dev/null ++++ b/configs/mt7981_bazis_ax3000wm_defconfig +@@ -0,0 +1,107 @@ ++CONFIG_ARM=y ++CONFIG_SYS_HAS_NONCACHED_MEMORY=y ++CONFIG_POSITION_INDEPENDENT=y ++CONFIG_ARCH_MEDIATEK=y ++CONFIG_TEXT_BASE=0x41e00000 ++CONFIG_SYS_MALLOC_F_LEN=0x4000 ++CONFIG_NR_DRAM_BANKS=1 ++CONFIG_DEFAULT_DEVICE_TREE="mt7981-bazis-ax3000wm" ++CONFIG_OF_LIBFDT_OVERLAY=y ++CONFIG_TARGET_MT7981=y ++CONFIG_SYS_LOAD_ADDR=0x46000000 ++CONFIG_PRE_CON_BUF_ADDR=0x4007ef00 ++CONFIG_DEBUG_UART_BASE=0x11002000 ++CONFIG_DEBUG_UART_CLOCK=40000000 ++CONFIG_DEBUG_UART=y ++CONFIG_FIT=y ++CONFIG_BOOTDELAY=30 ++CONFIG_AUTOBOOT_KEYED=y ++CONFIG_AUTOBOOT_MENU_SHOW=y ++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7981-bazis-ax3000wm.dtb" ++CONFIG_LOGLEVEL=7 ++CONFIG_PRE_CONSOLE_BUFFER=y ++CONFIG_LOG=y ++# CONFIG_BOARD_INIT is not set ++CONFIG_BOARD_LATE_INIT=y ++CONFIG_HUSH_PARSER=y ++CONFIG_SYS_PROMPT="MT7981> " ++CONFIG_CMD_CPU=y ++CONFIG_CMD_LICENSE=y ++CONFIG_CMD_BOOTMENU=y ++CONFIG_CMD_ASKENV=y ++CONFIG_CMD_ERASEENV=y ++CONFIG_CMD_ENV_FLAGS=y ++CONFIG_CMD_STRINGS=y ++CONFIG_CMD_DM=y ++CONFIG_CMD_GPIO=y ++CONFIG_CMD_GPT=y ++CONFIG_CMD_MTD=y ++CONFIG_CMD_PART=y ++CONFIG_CMD_TFTPSRV=y ++CONFIG_CMD_RARP=y ++CONFIG_CMD_CDP=y ++CONFIG_CMD_SNTP=y ++CONFIG_CMD_LINK_LOCAL=y ++CONFIG_CMD_DHCP=y ++CONFIG_CMD_DNS=y ++CONFIG_CMD_PING=y ++CONFIG_CMD_PXE=y ++CONFIG_CMD_CACHE=y ++CONFIG_CMD_PSTORE=y ++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000 ++CONFIG_CMD_UUID=y ++CONFIG_CMD_HASH=y ++CONFIG_CMD_SMC=y ++CONFIG_CMD_UBI=y ++CONFIG_CMD_UBI_RENAME=y ++CONFIG_OF_EMBED=y ++CONFIG_ENV_OVERWRITE=y ++CONFIG_ENV_IS_IN_UBI=y ++CONFIG_ENV_REDUNDANT=y ++CONFIG_ENV_UBI_PART="ubi" ++CONFIG_ENV_UBI_VOLUME="ubootenv" ++CONFIG_ENV_UBI_VOLUME_REDUND="ubootenv2" ++CONFIG_ENV_RELOC_GD_ENV_ADDR=y ++CONFIG_ENV_USE_DEFAULT_ENV_TEXT_FILE=y ++CONFIG_ENV_DEFAULT_ENV_TEXT_FILE="defenvs/bazis_ax3000wm_env" ++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y ++CONFIG_VERSION_VARIABLE=y ++CONFIG_NETCONSOLE=y ++CONFIG_USE_IPADDR=y ++CONFIG_IPADDR="192.168.1.1" ++CONFIG_USE_SERVERIP=y ++CONFIG_SERVERIP="192.168.1.254" ++CONFIG_NET_RANDOM_ETHADDR=y ++CONFIG_BUTTON=y ++CONFIG_BUTTON_GPIO=y ++CONFIG_CLK=y ++CONFIG_GPIO_HOG=y ++CONFIG_LED=y ++CONFIG_LED_BLINK=y ++CONFIG_LED_GPIO=y ++# CONFIG_MMC is not set ++CONFIG_MTD=y ++CONFIG_DM_MTD=y ++CONFIG_MTD_SPI_NAND=y ++CONFIG_MTD_UBI_FASTMAP=y ++CONFIG_PHY_FIXED=y ++CONFIG_MEDIATEK_ETH=y ++CONFIG_PHY=y ++CONFIG_PHY_MTK_TPHY=y ++CONFIG_PINCTRL=y ++CONFIG_PINCONF=y ++CONFIG_PINCTRL_MT7981=y ++CONFIG_POWER_DOMAIN=y ++CONFIG_MTK_POWER_DOMAIN=y ++CONFIG_DM_REGULATOR=y ++CONFIG_DM_REGULATOR_FIXED=y ++CONFIG_DM_REGULATOR_GPIO=y ++CONFIG_RAM=y ++CONFIG_DM_SERIAL=y ++CONFIG_SERIAL_RX_BUFFER=y ++CONFIG_MTK_SERIAL=y ++CONFIG_SPI=y ++CONFIG_DM_SPI=y ++CONFIG_MTK_SPIM=y ++CONFIG_ZSTD=y ++CONFIG_HEXDUMP=y +--- /dev/null ++++ b/arch/arm/dts/mt7981-bazis-ax3000wm.dts +@@ -0,0 +1,159 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * Copyright (c) 2026 ++ * Author: Fil Dunsky ++ */ ++ ++/dts-v1/; ++#include "mt7981.dtsi" ++#include ++#include ++ ++/ { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ model = "Bazis AX3000WM"; ++ compatible = "bazis,ax3000wm", "mediatek,mt7981"; ++ ++ chosen { ++ stdout-path = &uart0; ++ tick-timer = &timer0; ++ }; ++ ++ memory@40000000 { ++ device_type = "memory"; ++ reg = <0x40000000 0x10000000>; ++ }; ++ ++ gpio-keys { ++ compatible = "gpio-keys"; ++ ++ reset { ++ label = "reset"; ++ linux,code = ; ++ gpios = <&pio 1 GPIO_ACTIVE_LOW>; ++ }; ++ ++ mesh { ++ label = "mesh"; ++ linux,code = ; ++ gpios = <&pio 0 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ ++ led_status: led_power { ++ label = "blue:power"; ++ gpios = <&pio 13 GPIO_ACTIVE_LOW>; ++ }; ++ ++ led_warning: led_fault { ++ label = "red:fault"; ++ gpios = <&pio 34 GPIO_ACTIVE_LOW>; ++ }; ++ ++ led_status_green: led-2 { ++ label = "green:status"; ++ gpios = <&pio 35 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++}; ++ ++&uart0 { ++ mediatek,force-highspeed; ++ status = "okay"; ++}; ++ ++ð { ++ status = "okay"; ++ mediatek,gmac-id = <1>; ++ phy-mode = "gmii"; ++ phy-handle = <&phy0>; ++ ++ mdio { ++ phy0: ethernet-phy@0 { ++ compatible = "ethernet-phy-id03a2.9461"; ++ reg = <0x0>; ++ phy-mode = "gmii"; ++ }; ++ }; ++}; ++ ++&pio { ++ spi_flash_pins: spi0-pins-func-1 { ++ mux { ++ function = "flash"; ++ groups = "spi0", "spi0_wp_hold"; ++ }; ++ ++ conf-pu { ++ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; ++ drive-strength = ; ++ bias-pull-up = ; ++ }; ++ ++ conf-pd { ++ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; ++ drive-strength = ; ++ bias-pull-down = ; ++ }; ++ }; ++}; ++ ++&spi0 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi_flash_pins>; ++ status = "okay"; ++ must_tx; ++ enhance_timing; ++ dma_ext; ++ ipm_design; ++ support_quad; ++ tick_dly = <2>; ++ sample_sel = <0>; ++ ++ spi_nand@0 { ++ compatible = "spi-nand"; ++ reg = <0>; ++ spi-max-frequency = <52000000>; ++ ++ partitions { ++ compatible = "fixed-partitions"; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ partition@0 { ++ label = "BL2"; ++ reg = <0x0 0x100000>; ++ }; ++ ++ partition@100000 { ++ label = "u-boot-env"; ++ reg = <0x100000 0x80000>; ++ }; ++ ++ partition@180000 { ++ label = "Factory"; ++ reg = <0x180000 0x200000>; ++ }; ++ ++ partition@380000 { ++ label = "FIP"; ++ reg = <0x380000 0x200000>; ++ }; ++ ++ partition@580000 { ++ label = "ubi"; ++ reg = <0x580000 0x7a40000>; ++ }; ++ }; ++ }; ++}; ++ ++&watchdog { ++ status = "disabled"; ++}; +--- /dev/null ++++ b/defenvs/bazis_ax3000wm_env +@@ -0,0 +1,54 @@ ++ipaddr=192.168.1.1 ++serverip=192.168.1.254 ++loadaddr=0x46000000 ++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0 ++bootcmd=if pstore check ; then run boot_recovery ; else run boot_ubi ; fi ++bootconf=config-1 ++bootdelay=0 ++bootfile=openwrt-mediatek-filogic-bazis_ax3000wm-initramfs-recovery.itb ++bootfile_bl2=openwrt-mediatek-filogic-bazis_ax3000wm-preloader.bin ++bootfile_fip=openwrt-mediatek-filogic-bazis_ax3000wm-bl31-uboot.fip ++bootfile_upg=openwrt-mediatek-filogic-bazis_ax3000wm-squashfs-sysupgrade.itb ++bootled_pwr=blue:power ++bootled_rec=red:fault ++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60 ++bootmenu_default=0 ++bootmenu_delay=0 ++bootmenu_title= ( ( ( OpenWrt ) ) ) ++bootmenu_0=Initialize environment.=run _firstboot ++bootmenu_0d=Run default boot command.=run boot_default ++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return ++bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return ++bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return ++bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return ++bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return ++bootmenu_6=Load BL31+U-Boot FIP via TFTP then write to NAND.=run boot_tftp_write_fip ; run bootmenu_confirm_return ++bootmenu_7=Load BL2 preloader via TFTP then write to NAND.=run boot_tftp_write_bl2 ; run bootmenu_confirm_return ++bootmenu_8=Reboot.=reset ++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset ++boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu ++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever ++boot_production=led $bootled_pwr on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off ++boot_recovery=led $bootled_rec on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off ++boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever ++boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done ++boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi ++boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi ++boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf ++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run mtd_write_fip && run reset_factory ++boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run mtd_write_bl2 ++reset_factory=ubi part ubi ; mw $loadaddr 0x0 0x800 ; ubi write $loadaddr ubootenv 0x800 ; ubi write $loadaddr ubootenv2 0x800 ++mtd_write_fip=mtd erase fip && mtd write fip $loadaddr ++mtd_write_bl2=mtd erase bl2 && mtd write bl2 $loadaddr ++ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic || run ubi_format ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic || run ubi_format ++ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset ++ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi ++ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs ++ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery ++ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data ++ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic && ubi write $loadaddr fit $filesize ++ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic && ubi write $loadaddr recovery $filesize ++_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv ++_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first ++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title ++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title $ver" diff --git a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface index 5d3a3319fc0..828912ca229 100644 --- a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface +++ b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface @@ -1,5 +1,6 @@ set_preinit_iface() { case $(board_name) in + bazis,ax3000wm|\ cudy,m3000-v1|\ cudy,tr3000-256mb-v1|\ cudy,tr3000-v1|\ diff --git a/target/linux/mediatek/dts/mt7981b-bazis-ax3000wm.dts b/target/linux/mediatek/dts/mt7981b-bazis-ax3000wm.dts new file mode 100644 index 00000000000..34df1ffc56c --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-bazis-ax3000wm.dts @@ -0,0 +1,297 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/* + * Copyright (c) 2026 + * Author: Fil Dunsky + */ + +/dts-v1/; +#include +#include "mt7981b.dtsi" + +/ { + model = "Bazis AX3000WM"; + compatible = "bazis,ax3000wm", "mediatek,mt7981"; + + aliases { + label-mac-device = &gmac1; + led-boot = &led_status; + led-failsafe = &led_warning; + led-running = &led_status; + led-upgrade = &led_warning; + serial0 = &uart0; + }; + + chosen: chosen { + stdout-path = "serial0:115200n8"; + bootargs = "root=/dev/fit0 rootwait"; + rootdisk = <&ubi_rootdisk>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + + mesh { + label = "mesh"; + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_wlan-2ghz { + function = LED_FUNCTION_WLAN_2GHZ; + color = ; + gpios = <&pio 4 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + led_warning: led_fault { + function = LED_FUNCTION_FAULT; + color = ; + gpios = <&pio 34 GPIO_ACTIVE_LOW>; + }; + + led_internet { + function = LED_FUNCTION_WAN_ONLINE; + color = ; + gpios = <&pio 8 GPIO_ACTIVE_LOW>; + }; + + led_status: led_power { + function = LED_FUNCTION_POWER; + color = ; + gpios = <&pio 13 GPIO_ACTIVE_LOW>; + }; + + led_wlan-5ghz { + function = LED_FUNCTION_WLAN_5GHZ; + color = ; + gpios = <&pio 35 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + led_lan_back { + function = LED_FUNCTION_LAN; + color = ; + gpios = <&pio 6 GPIO_ACTIVE_LOW>; + }; + }; + + usb_vbus: regulator-usb { + compatible = "regulator-fixed"; + regulator-name = "usb-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpios = <&pio 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + phy-handle = <&phy5>; + nvmem-cell-names = "mac-address"; + nvmem-cells = <&mac_wan>; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "gmii"; + phy-handle = <&int_gbe_phy>; + nvmem-cell-names = "mac-address"; + nvmem-cells = <&mac_lan>; + }; +}; + +&mdio_bus { + reset-gpios = <&pio 14 GPIO_ACTIVE_LOW>; + reset-delay-us = <600>; + reset-post-delay-us = <20000>; + + /* MaxLinear GPY211C 2.5G PHY */ + phy5: phy@5 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <5>; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + led@2 { + reg = <2>; + color = ; + function = LED_FUNCTION_WAN; + }; + + led@3 { + reg = <3>; + color = ; + function = LED_FUNCTION_WAN; + }; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand: flash@0 { + compatible = "spi-nand"; + reg = <0>; + + spi-max-frequency = <52000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + spi-cal-enable; + spi-cal-mode = "read-data"; + spi-cal-datalen = <7>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>; + spi-cal-addrlen = <5>; + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x00000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x0200000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1000>; + }; + + mac_lan: macaddr@4 { + reg = <0x4 0x6>; + }; + + mac_wan: macaddr@a { + reg = <0xa 0x6>; + }; + + mac_wlan_2ghz: macaddr@2a { + reg = <0x2a 0x6>; + }; + + mac_wlan_5ghz: macaddr@24 { + reg = <0x24 0x6>; + }; + + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x0200000>; + read-only; + }; + + ubi: partition@580000 { + label = "ubi"; + reg = <0x580000 0x7a40000>; + compatible = "linux,ubi"; + + volumes { + ubi_rootdisk: ubi-volume-fit { + volname = "fit"; + }; + + ubi_ubootenv: ubi-volume-ubootenv { + volname = "ubootenv"; + }; + + ubi_ubootenv2: ubi-volume-ubootenv2 { + volname = "ubootenv2"; + }; + }; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + nvmem-cells = <&eeprom_factory_0>; + nvmem-cell-names = "eeprom"; + + band@0 { + reg = <0>; + nvmem-cells = <&mac_wlan_2ghz>; + nvmem-cell-names = "mac-address"; + }; + + band@1 { + reg = <1>; + nvmem-cells = <&mac_wlan_5ghz>; + nvmem-cell-names = "mac-address"; + }; +}; + +&xhci { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index 7df1700f317..3bf561793db 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -62,6 +62,12 @@ bananapi,bpi-r4-poe) bananapi,bpi-r4-lite) ucidef_set_led_netdev "sfp0" "sfp0" "green:sfp" "sfp0" "link tx rx" ;; +bazis,ax3000wm) + ucidef_set_led_netdev "wanact" "WANACT" "mdio-bus:05:amber:wan" "eth0" "rx tx" + ucidef_set_led_netdev "wanlink" "WANLINK" "mdio-bus:05:green:wan" "eth0" "link" + ucidef_set_led_netdev "lanlink" "LANLINK" "green:lan" "eth1" "link" + ucidef_set_led_netdev "internet" "internet" "blue:wan-online" "wan" "link" + ;; cudy,re3000-v1|\ kebidumei,ax3000-u22|\ wavlink,wl-wn573hx3) diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 4ffff062cde..a07b5c136f2 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -124,6 +124,7 @@ mediatek_setup_interfaces() huasifei,wh3000-pro) ucidef_set_interfaces_lan_wan eth0 eth1 ;; + bazis,ax3000wm|\ cudy,m3000-v1|\ cudy,tr3000-256mb-v1|\ cudy,tr3000-v1|\ diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index dde54a053df..01858dbf7cd 100644 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -87,6 +87,7 @@ platform_do_upgrade() { bananapi,bpi-r4-2g5|\ bananapi,bpi-r4-poe|\ bananapi,bpi-r4-lite|\ + bazis,ax3000wm|\ cmcc,a10-ubootmod|\ cmcc,rax3000m|\ comfast,cf-wr632ax-ubootmod|\ @@ -278,6 +279,7 @@ platform_check_image() { bananapi,bpi-r4-2g5|\ bananapi,bpi-r4-poe|\ bananapi,bpi-r4-lite|\ + bazis,ax3000wm|\ cmcc,a10-ubootmod|\ cmcc,rax3000m|\ comfast,cf-wr632ax-ubootmod|\ diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 5f15c7f9a9c..ac2776fa9ac 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -805,6 +805,31 @@ endif endef TARGET_DEVICES += bananapi_bpi-r4-lite +define Device/bazis_ax3000wm + DEVICE_VENDOR := Bazis + DEVICE_MODEL := AX3000WM + DEVICE_DTS := mt7981b-bazis-ax3000wm + DEVICE_DTS_DIR := ../dts + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_IN_UBI := 1 + UBOOTENV_IN_UBI := 1 + IMAGES := sysupgrade.itb + KERNEL_INITRAMFS_SUFFIX := -recovery.itb + KERNEL := kernel-bin | gzip + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k + IMAGE/sysupgrade.itb := append-kernel | \ + fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | \ + append-metadata + DEVICE_PACKAGES := kmod-usb3 kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware + ARTIFACTS := preloader.bin bl31-uboot.fip + ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3 + ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot bazis-ax3000wm +endef +TARGET_DEVICES += bazis_ax3000wm + define Device/buffalo_wsr-6000ax8 DEVICE_MODEL := WSR-6000AX8 DEVICE_VENDOR := Buffalo -- 2.47.3