spi: zynq_qspi: Dont clear the previous config register

Dont clear the previous config register as the iMPACT tool
expects the u-boot to keep settings of the config register
for flashing.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

diff --git a/drivers/spi/zynq_qspi.c b/drivers/spi/zynq_qspi.c
index 04e35ff113ea9eda261bab9469f85ab3fa3642dd..6a30c4a685cb85d652104e3512c64667aca7b75b 100644 (file)
--- a/drivers/spi/zynq_qspi.c
+++ b/drivers/spi/zynq_qspi.c
@@ -29,31 +29,15 @@
  * of the QSPI controller
  */
 #define ZYNQ_QSPI_CONFIG_IFMODE_MASK   (1 << 31)  /* Flash intrface mode*/
-#define ZYNQ_QSPI_CONFIG_HOLDB_MASK    (1 << 19)  /* Holdb Mask */
 #define ZYNQ_QSPI_CONFIG_MSA_MASK      (1 << 15)  /* Manual start enb */
 #define ZYNQ_QSPI_CONFIG_MCS_MASK      (1 << 14)  /* Manual chip select */
 #define ZYNQ_QSPI_CONFIG_PCS_MASK      (1 << 10)  /* Peri chip select */
-#define ZYNQ_QSPI_CONFIG_REFCLK_MASK   (1 << 8)   /* Ref Clock Mask */
 #define ZYNQ_QSPI_CONFIG_FW_MASK       (0x3 << 6) /* FIFO width */
-#define ZYNQ_QSPI_CONFIG_BAUDRATE_MASK (0x7 << 3) /* Baudrate Divisor Mask */
 #define ZYNQ_QSPI_CONFIG_MSTREN_MASK   (1 << 0)   /* Mode select */
 #define ZYNQ_QSPI_CONFIG_MANSRT_MASK   0x00010000 /* Manual TX Start */
 #define ZYNQ_QSPI_CONFIG_CPHA_MASK     0x00000004 /* Clock Phase Control */
 #define ZYNQ_QSPI_CONFIG_CPOL_MASK     0x00000002 /* Clock Polarity Control */
 #define ZYNQ_QSPI_CONFIG_SSCTRL_MASK   0x00003C00 /* Slave Select Mask */
-#define ZYNQ_QSPI_CONFIG_CLR_ALL_MASK  (ZYNQ_QSPI_CONFIG_IFMODE_MASK | \
-                                       ZYNQ_QSPI_CONFIG_HOLDB_MASK | \
-                                       ZYNQ_QSPI_CONFIG_MANSRT_MASK | \
-                                       ZYNQ_QSPI_CONFIG_MSA_MASK | \
-                                       ZYNQ_QSPI_CONFIG_MCS_MASK | \
-                                       ZYNQ_QSPI_CONFIG_PCS_MASK | \
-                                       ZYNQ_QSPI_CONFIG_REFCLK_MASK | \
-                                       ZYNQ_QSPI_CONFIG_FW_MASK | \
-                                       ZYNQ_QSPI_CONFIG_BAUDRATE_MASK | \
-                                       ZYNQ_QSPI_CONFIG_CPHA_MASK | \
-                                       ZYNQ_QSPI_CONFIG_CPOL_MASK | \
-                                       ZYNQ_QSPI_CONFIG_MSTREN_MASK)
-
 /*
  * QSPI Interrupt Registers bit Masks
  *
@@ -275,8 +259,6 @@ static void zynq_qspi_init_hw(int is_dual, unsigned int cs)
 
        writel(0x7F, &zynq_qspi_base->isr);
        config_reg = readl(&zynq_qspi_base->confr);
-       /* Clear all the bits before setting required configuration */
-       config_reg &= ~ZYNQ_QSPI_CONFIG_CLR_ALL_MASK;
        config_reg |= ZYNQ_QSPI_CONFIG_IFMODE_MASK |
                ZYNQ_QSPI_CONFIG_MCS_MASK | ZYNQ_QSPI_CONFIG_PCS_MASK |
                ZYNQ_QSPI_CONFIG_FW_MASK | ZYNQ_QSPI_CONFIG_MSTREN_MASK;