--- /dev/null
+/*
+ * dts file for Xilinx ZynqMP ZCU104
+ *
+ * (C) Copyright 2017, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+ model = "ZynqMP ZCU104 RevC";
+ compatible = "xlnx,zynqmp-zcu104-revC", "xlnx,zynqmp-zcu104", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem3;
+ gpio0 = &gpio;
+ i2c0 = &i2c1;
+ mmc0 = &sdhci1;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &dcc;
+ spi0 = &qspi;
+ usb0 = &usb0;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+};
+
+&can1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1_default>;
+};
+
+&dcc {
+ status = "okay";
+};
+
+&gem3 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem3_default>;
+ phy0: phy@c {
+ reg = <0xc>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ ti,rxctrl-strap-worka;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+
+ tca6416_u97: gpio@21 {
+ compatible = "ti,tca6416";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /*
+ * IRQ not connected
+ * Lines:
+ * 0 - IRPS5401_ALERT_B
+ * 1 - HDMI_8T49N241_INT_ALM
+ * 2 - MAX6643_OT_B
+ * 3 - MAX6643_FANFAIL_B
+ * 5 - IIC_MUX_RESET_B
+ * 6 - GEM3_EXP_RESET_B
+ * 7 - FMC_LPC_PRSNT_M2C_B
+ * 4, 10 - 17 - not connected
+ */
+ };
+
+ /* Another connection to this bus via PL i2c via PCA9306 - u45 */
+ i2cswitch@74 { /* u34 */
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+ i2c@0 { /* i2c mw 74 0 1 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /*
+ * IIC_EEPROM 1kB memory which uses 256B blocks
+ * where every block has different address.
+ * 0 - 256B address 0x54
+ * 256B - 512B address 0x55
+ * 512B - 768B address 0x56
+ * 768B - 1024B address 0x57
+ */
+ eeprom@54 { /* u23 */
+ compatible = "at,24c08";
+ reg = <0x54>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+
+ i2c@1 { /* i2c mw 74 0 2 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ clock_8t49n287: 8t49n287@6c { /* 8T49N287 - u182 */
+ compatible = "idt,8t49n287";
+ reg = <0x6c>;
+ };
+ };
+
+ i2c@2 { /* i2c mw 74 0 4 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ irps5401_43: irps54012@43 { /* IRPS5401 - u175 */
+ #clock-cells = <0>;
+ compatible = "infineon,irps5401";
+ reg = <0x43>;
+ };
+ irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */
+ #clock-cells = <0>;
+ compatible = "infineon,irps5401";
+ reg = <0x4d>;
+ };
+ };
+
+ i2c@4 { /* i2c mw 74 0 8 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ i2c@5 { /* i2c mw 74 0 10 */ /* FMC_LPC */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ i2c@7 { /* i2c mw 74 0 14 */ /* DDR4_SODIMM */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+
+ /* 3, 6 not connected */
+ };
+};
+
+&pinctrl0 {
+ status = "okay";
+
+ pinctrl_can1_default: can1-default {
+ mux {
+ function = "can1";
+ groups = "can1_6_grp";
+ };
+
+ conf {
+ groups = "can1_6_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO25";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO24";
+ bias-disable;
+ };
+ };
+
+ pinctrl_i2c1_default: i2c1-default {
+ mux {
+ groups = "i2c1_4_grp";
+ function = "i2c1";
+ };
+
+ conf {
+ groups = "i2c1_4_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio {
+ mux {
+ groups = "gpio0_16_grp", "gpio0_17_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_16_grp", "gpio0_17_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+ };
+
+ pinctrl_gem3_default: gem3-default {
+ mux {
+ function = "ethernet3";
+ groups = "ethernet3_0_grp";
+ };
+
+ conf {
+ groups = "ethernet3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+ "MIO75";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+ "MIO69";
+ bias-disable;
+ low-power-enable;
+ };
+
+ mux-mdio {
+ function = "mdio3";
+ groups = "mdio3_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_sdhci1_default: sdhci1-default {
+ mux {
+ groups = "sdio1_0_grp";
+ function = "sdio1";
+ };
+
+ conf {
+ groups = "sdio1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ drive-strength = <12>;
+ };
+
+ mux-cd {
+ groups = "sdio1_0_cd_grp";
+ function = "sdio1_cd";
+ };
+
+ conf-cd {
+ groups = "sdio1_0_cd_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_uart0_default: uart0-default {
+ mux {
+ groups = "uart0_4_grp";
+ function = "uart0";
+ };
+
+ conf {
+ groups = "uart0_4_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO18";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO19";
+ bias-disable;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ groups = "uart1_5_grp";
+ function = "uart1";
+ };
+
+ conf {
+ groups = "uart1_5_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO21";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO20";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb0_default: usb0-default {
+ mux {
+ groups = "usb0_0_grp";
+ function = "usb0";
+ };
+
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO52", "MIO53", "MIO55";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+ "MIO60", "MIO61", "MIO62", "MIO63";
+ bias-disable;
+ };
+ };
+};
+
+&qspi {
+ status = "okay";
+ flash@0 {
+ compatible = "m25p80"; /* n25q512a 128MiB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ /* SATA OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ phy-names = "sata-phy";
+ phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+ status = "okay";
+ no-1-8-v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci1_default>;
+ xlnx,mio_bank = <1>;
+ disable-wp;
+};
+
+&serdes {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
+};
+
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
+};
+
+&dwc3_0 {
+ status = "okay";
+ dr_mode = "host";
+ snps,usb3_lpm_capable;
+ phy-names = "usb3-phy";
+ phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
+ maximum-speed = "super-speed";
+};
+
+&watchdog0 {
+ status = "okay";
+};
+
+&xilinx_ams {
+ status = "okay";
+};
+
+&ams_ps {
+ status = "okay";
+};
+
+&ams_pl {
+ status = "okay";
+};
+
+&xilinx_drm {
+ status = "okay";
+};
+
+&xlnx_dp {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&lane1 PHY_TYPE_DP 0 3 27000000>, <&lane0 PHY_TYPE_DP 1 3 27000000>;
+};
+
+&xlnx_dp_sub {
+ status = "okay";
+};
+
+&xlnx_dp_snd_pcm0 {
+ status = "okay";
+};
+
+&xlnx_dp_snd_pcm1 {
+ status = "okay";
+};
+
+&xlnx_dp_snd_card {
+ status = "okay";
+};
+
+&xlnx_dp_snd_codec0 {
+ status = "okay";
+};
+
+&xlnx_dpdma {
+ status = "okay";
+};
--- /dev/null
+CONFIG_ARM=y
+CONFIG_SYS_CONFIG_NAME="xilinx_zynqmp_zcu104"
+CONFIG_ARCH_ZYNQMP=y
+CONFIG_SYS_TEXT_BASE=0x8000000
+CONFIG_SYS_MALLOC_F_LEN=0x8000
+CONFIG_IDENT_STRING=" Xilinx ZynqMP ZCU104 revC"
+CONFIG_ZYNQMP_QSPI=y
+CONFIG_ZYNQMP_USB=y
+CONFIG_SPI_GENERIC=y
+CONFIG_DEFAULT_DEVICE_TREE="zynqmp-zcu104-revC"
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_BOOTCOMMAND="run $modeboot"
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SPL=y
+CONFIG_SPL_OS_BOOT=y
+CONFIG_SPL_RAM_SUPPORT=y
+CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SYS_PROMPT="ZynqMP> "
+CONFIG_CMD_EEPROM=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DFU=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_FPGA_LOADBP=y
+CONFIG_CMD_FPGA_LOADP=y
+CONFIG_CMD_FPGA_LOAD_SECURE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_TIMER=y
+CONFIG_CMD_AES=y
+CONFIG_CMD_EXT4_WRITE=y
+# CONFIG_SPL_ISO_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_EMBED=y
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SCSI_AHCI=y
+CONFIG_SATA_CEVA=y
+CONFIG_CLK_ZYNQMP=y
+CONFIG_DFU_RAM=y
+CONFIG_FPGA_XILINX=y
+CONFIG_FPGA_ZYNQMPPL=y
+CONFIG_DM_GPIO=y
+CONFIG_CMD_PCA953X=y
+CONFIG_MISC=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ZYNQ=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SF_DUAL_FLASH=y
+CONFIG_SPI_FLASH_ISSI=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_DM_ETH=y
+CONFIG_PHY_GIGE=y
+CONFIG_ZYNQ_GEM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_DEBUG_UART_ZYNQ=y
+CONFIG_DEBUG_UART_BASE=0xff000000
+CONFIG_DEBUG_UART_CLOCK=100000000
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ZYNQ_SERIAL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_XHCI_ZYNQMP=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GADGET=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_USB_ULPI_VIEWPORT=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
projects / thirdparty / u-boot.git / commitdiff
