extern struct rtl83xx_soc_info soc_info;
-extern int rtmdio_930x_read_sds_phy(int sds, int page, int regnum);
-extern int rtmdio_930x_write_sds_phy(int sds, int page, int regnum, u16 val);
-
-#define PHY_PAGE_2 2
-#define PHY_PAGE_4 4
-
/* all Clause-22 RealTek MDIO PHYs use register 0x1f for page select */
#define RTL8XXX_PAGE_SELECT 0x1f
#define RTL821X_MEDIA_PAGE_FIBRE 3
#define RTL821X_MEDIA_PAGE_INTERNAL 8
-#define RTL9300_PHY_ID_MASK 0xf0ffffff
-
-/* RTL930X SerDes supports the following modes:
- * 0x02: SGMII 0x04: 1000BX_FIBER 0x05: FIBER100
- * 0x06: QSGMII 0x09: RSGMII 0x0d: USXGMII
- * 0x10: XSGMII 0x12: HISGMII 0x16: 2500Base_X
- * 0x17: RXAUI_LITE 0x19: RXAUI_PLUS 0x1a: 10G Base-R
- * 0x1b: 10GR1000BX_AUTO 0x1f: OFF
- */
-#define RTL930X_SDS_MODE_SGMII 0x02
-#define RTL930X_SDS_MODE_1000BASEX 0x04
-#define RTL930X_SDS_MODE_USXGMII 0x0d
-#define RTL930X_SDS_MODE_XGMII 0x10
-#define RTL930X_SDS_MODE_2500BASEX 0x16
-#define RTL930X_SDS_MODE_10GBASER 0x1a
-#define RTL930X_SDS_OFF 0x1f
-#define RTL930X_SDS_MASK 0x1f
-
-/* RTL930X SerDes supports two submodes when mode is USXGMII:
- * 0x00: USXGMII (aka USXGMII_SX)
- * 0x02: 10G_QXGMII (aka USXGMII_QX)
- */
-#define RTL930X_SDS_SUBMODE_USXGMII_SX 0x0
-#define RTL930X_SDS_SUBMODE_USXGMII_QX 0x2
-
-#define RTSDS_930X_PLL_1000 0x1
-#define RTSDS_930X_PLL_10000 0x5
-#define RTSDS_930X_PLL_2500 0x3
-#define RTSDS_930X_PLL_LC 0x3
-#define RTSDS_930X_PLL_RING 0x1
-
static const struct firmware rtl838x_8380_fw;
static const struct firmware rtl838x_8214fc_fw;
static const struct firmware rtl838x_8218b_fw;
phy_modify(phydev, 0, BMCR_RESET, BMCR_RESET);
}
-/* The access registers for SDS_MODE_SEL and the LSB for each SDS within */
-u16 rtl9300_sds_regs[] = { 0x0194, 0x0194, 0x0194, 0x0194, 0x02a0, 0x02a0, 0x02a0, 0x02a0,
- 0x02A4, 0x02A4, 0x0198, 0x0198 };
-u8 rtl9300_sds_lsb[] = { 0, 6, 12, 18, 0, 6, 12, 18, 0, 6, 0, 6};
-
-u16 rtl9300_sds_submode_regs[] = { 0x1cc, 0x1cc, 0x2d8, 0x2d8, 0x2d8, 0x2d8,
- 0x2d8, 0x2d8};
-u8 rtl9300_sds_submode_lsb[] = { 0, 5, 0, 5, 10, 15, 20, 25 };
-
-void rtl9300_sds_set(int sds_num, u32 mode)
-{
- pr_info("%s %d\n", __func__, mode);
- if (sds_num < 0 || sds_num > 11) {
- pr_err("Wrong SerDes number: %d\n", sds_num);
- return;
- }
-
- sw_w32_mask(RTL930X_SDS_MASK << rtl9300_sds_lsb[sds_num], mode << rtl9300_sds_lsb[sds_num],
- rtl9300_sds_regs[sds_num]);
- mdelay(10);
-
- pr_debug("%s: 194:%08x 198:%08x 2a0:%08x 2a4:%08x\n", __func__,
- sw_r32(0x194), sw_r32(0x198), sw_r32(0x2a0), sw_r32(0x2a4));
-}
-
-static u32 rtl9300_sds_mode_get(int sds_num)
-{
- u32 v;
-
- if (sds_num < 0 || sds_num > 11) {
- pr_err("Wrong SerDes number: %d\n", sds_num);
- return 0;
- }
-
- v = sw_r32(rtl9300_sds_regs[sds_num]);
- v >>= rtl9300_sds_lsb[sds_num];
-
- return v & RTL930X_SDS_MASK;
-}
-
-static u32 rtl9300_sds_submode_get(int sds_num)
-{
- u32 v;
-
- if (sds_num < 2 || sds_num > 9) {
- pr_err("%s: unsupported SerDes %d\n", __func__, sds_num);
- return 0;
- }
-
- v = sw_r32(rtl9300_sds_submode_regs[sds_num]);
- v >>= rtl9300_sds_submode_lsb[sds_num];
-
- return v & RTL930X_SDS_MASK;
-}
-
-static void rtsds_930x_submode_set(int sds, u32 submode) {
- if (sds < 2 || sds > 9) {
- pr_err("%s: submode unsupported on serdes %d\n", __func__, sds);
- return;
- }
- if (submode != RTL930X_SDS_SUBMODE_USXGMII_SX &&
- submode != RTL930X_SDS_SUBMODE_USXGMII_QX) {
- pr_err("%s: unsupported submode 0x%x\n", __func__, submode);
- }
- sw_w32_mask(RTL930X_SDS_MASK << rtl9300_sds_submode_lsb[sds-2],
- submode << rtl9300_sds_submode_lsb[sds-2],
- rtl9300_sds_submode_regs[sds-2]);
-}
-
/* Read the link and speed status of the 2 internal SGMII/1000Base-X
* ports of the RTL838x SoCs
*/
return 0;
}
-static void rtl9300_sds_field_w(int sds, u32 page, u32 reg, int end_bit, int start_bit, u32 v)
-{
- int l = end_bit - start_bit + 1;
- u32 data = v;
-
- if (l < 32) {
- u32 mask = BIT(l) - 1;
-
- data = rtmdio_930x_read_sds_phy(sds, page, reg);
- data &= ~(mask << start_bit);
- data |= (v & mask) << start_bit;
- }
-
- rtmdio_930x_write_sds_phy(sds, page, reg, data);
-}
-
-static u32 rtl9300_sds_field_r(int sds, u32 page, u32 reg, int end_bit, int start_bit)
-{
- int l = end_bit - start_bit + 1;
- u32 v = rtmdio_930x_read_sds_phy(sds, page, reg);
-
- if (l >= 32)
- return v;
-
- return (v >> start_bit) & (BIT(l) - 1);
-}
-
-/* Read the link and speed status of the internal SerDes of the RTL9300
- */
-static int rtl9300_read_status(struct phy_device *phydev)
-{
- struct device *dev = &phydev->mdio.dev;
- int phy_addr = phydev->mdio.addr;
- struct device_node *dn;
- u32 sds_num = 0, status, latch_status, latch_status1, mode, submode;
-
- if (dev->of_node) {
- dn = dev->of_node;
-
- if (of_property_read_u32(dn, "sds", &sds_num))
- sds_num = -1;
- pr_debug("%s: Port %d, SerDes is %d\n", __func__, phy_addr, sds_num);
- } else {
- dev_err(dev, "No DT node.\n");
- return -EINVAL;
- }
-
- if (sds_num < 0)
- return 0;
-
- mode = rtl9300_sds_mode_get(sds_num);
- pr_debug("%s got SDS mode %02x\n", __func__, mode);
- if (mode == RTL930X_SDS_OFF)
- mode = rtl9300_sds_field_r(sds_num, 0x1f, 9, 11, 7);
- if (mode == RTL930X_SDS_MODE_10GBASER) { /* 10GR mode */
- status = rtl9300_sds_field_r(sds_num, 0x5, 0, 12, 12);
- latch_status = rtl9300_sds_field_r(sds_num, 0x4, 1, 2, 2);
- status |= rtl9300_sds_field_r(sds_num, 0x5, 0, 12, 12);
- latch_status |= rtl9300_sds_field_r(sds_num, 0x4, 1, 2, 2);
- } else if (mode == RTL930X_SDS_MODE_USXGMII) {
- submode = rtl9300_sds_submode_get(sds_num);
- status = rtl9300_sds_field_r(sds_num, 0x5, 0, 12, 12);
- latch_status = rtl9300_sds_field_r(sds_num, 0x4, 1, 2, 2);
- latch_status1 = rtl9300_sds_field_r(sds_num, 0x7, 21, 14, 4);
- status |= rtl9300_sds_field_r(sds_num, 0x5, 0, 12, 12);
- latch_status |= rtl9300_sds_field_r(sds_num, 0x4, 1, 2, 2);
- latch_status1 |= rtl9300_sds_field_r(sds_num, 0x7, 21, 14, 4);
- } else {
- status = rtl9300_sds_field_r(sds_num, 0x1, 29, 8, 0);
- latch_status = rtl9300_sds_field_r(sds_num, 0x1, 30, 8, 0);
- status |= rtl9300_sds_field_r(sds_num, 0x1, 29, 8, 0);
- latch_status |= rtl9300_sds_field_r(sds_num, 0x1, 30, 8, 0);
- }
-
- pr_debug("%s link status: status: %d, latch %d\n", __func__, status, latch_status);
-
- if (latch_status) {
- phydev->link = true;
- if (mode == RTL930X_SDS_MODE_10GBASER) {
- phydev->speed = SPEED_10000;
- phydev->interface = PHY_INTERFACE_MODE_10GBASER;
- } else if (mode == RTL930X_SDS_MODE_USXGMII) {
- phydev->speed = SPEED_10000;
- if (submode == RTL930X_SDS_SUBMODE_USXGMII_QX) {
- phydev->interface = PHY_INTERFACE_MODE_10G_QXGMII;
- } else {
- phydev->interface = PHY_INTERFACE_MODE_USXGMII;
- }
- } else {
- phydev->speed = SPEED_1000;
- phydev->interface = PHY_INTERFACE_MODE_1000BASEX;
- }
-
- phydev->duplex = DUPLEX_FULL;
- }
-
- return 0;
-}
-
-static void rtl930x_sds_rx_rst(int sds_num, phy_interface_t phy_if)
-{
- int page = 0x2e; /* 10GR and USXGMII */
-
- if (phy_if == PHY_INTERFACE_MODE_1000BASEX)
- page = 0x24;
-
- rtl9300_sds_field_w(sds_num, page, 0x15, 4, 4, 0x1);
- mdelay(5);
- rtl9300_sds_field_w(sds_num, page, 0x15, 4, 4, 0x0);
-}
-
-static void rtsds_930x_get_pll_data(int sds, int *pll, int *speed)
-{
- int sbit, pbit = sds & 1 ? 6 : 4;
- int base_sds = sds & ~1;
-
- /*
- * PLL data is shared between adjacent SerDes in the even lane. Each SerDes defines
- * what PLL it needs (ring or LC) while the PLL itself stores the current speed.
- */
-
- *pll = rtl9300_sds_field_r(base_sds, 0x20, 0x12, pbit + 1, pbit);
- sbit = *pll == RTSDS_930X_PLL_LC ? 8 : 12;
- *speed = rtl9300_sds_field_r(base_sds, 0x20, 0x12, sbit + 3, sbit);
-}
-
-static int rtsds_930x_set_pll_data(int sds, int pll, int speed)
-{
- int sbit = pll == RTSDS_930X_PLL_LC ? 8 : 12;
- int pbit = sds & 1 ? 6 : 4;
- int base_sds = sds & ~1;
-
- if ((speed != RTSDS_930X_PLL_1000) &&
- (speed != RTSDS_930X_PLL_2500) &&
- (speed != RTSDS_930X_PLL_10000))
- return -EINVAL;
-
- if ((pll != RTSDS_930X_PLL_RING) && (pll != RTSDS_930X_PLL_LC))
- return -EINVAL;
-
- if ((pll == RTSDS_930X_PLL_RING) && (speed == RTSDS_930X_PLL_10000))
- return -EINVAL;
-
- /*
- * A SerDes clock can either be taken from the low speed ring PLL or the high speed
- * LC PLL. As it is unclear if disabling PLLs has any positive or negative effect,
- * always activate both.
- */
-
- rtl9300_sds_field_w(base_sds, 0x20, 0x12, 3, 0, 0xf);
- rtl9300_sds_field_w(base_sds, 0x20, 0x12, pbit + 1, pbit, pll);
- rtl9300_sds_field_w(base_sds, 0x20, 0x12, sbit + 3, sbit, speed);
-
- return 0;
-}
-
-static void rtsds_930x_reset_cmu(int sds)
-{
- int reset_sequence[4] = { 3, 2, 3, 1 };
- int base_sds = sds & ~1;
- int pll, speed, i, bit;
-
- /*
- * After the PLL speed has changed, the CMU must take over the new values. The models
- * of the Otto platform have different reset sequences. Luckily it always boils down
- * to flipping two bits in a special sequence.
- */
-
- rtsds_930x_get_pll_data(sds, &pll, &speed);
- bit = pll == RTSDS_930X_PLL_LC ? 2 : 0;
-
- for (i = 0; i < ARRAY_SIZE(reset_sequence); i++)
- rtl9300_sds_field_w(base_sds, 0x21, 0x0b, bit + 1, bit, reset_sequence[i]);
-}
-
-static int rtsds_930x_wait_clock_ready(int sds)
-{
- int i, base_sds = sds & ~1, ready, ready_cnt = 0, bit = (sds & 1) + 4;
-
- /*
- * While reconfiguring a SerDes it might take some time until its clock is in sync with
- * the PLL. During that timespan the ready signal might toggle randomly. According to
- * GPL sources it is enough to verify that 3 consecutive clock ready checks say "ok".
- */
-
- for (i = 0; i < 20; i++) {
- usleep_range(10000, 15000);
-
- rtmdio_930x_write_sds_phy(base_sds, 0x1f, 0x02, 53);
- ready = rtl9300_sds_field_r(base_sds, 0x1f, 0x14, bit, bit);
-
- ready_cnt = ready ? ready_cnt + 1 : 0;
- if (ready_cnt >= 3)
- return 0;
- }
-
- return -EBUSY;
-}
-
-static void rtsds_930x_set_internal_mode(int sds, int mode)
-{
- rtl9300_sds_field_w(sds, 0x1f, 0x09, 6, 6, 0x1); /* Force mode enable */
- rtl9300_sds_field_w(sds, 0x1f, 0x09, 11, 7, mode);
-}
-
-static int rtsds_930x_get_internal_mode(int sds)
-{
- return rtl9300_sds_field_r(sds, 0x1f, 0x09, 11, 7);
-}
-
-static void rtsds_930x_set_power(int sds, bool on)
-{
- int power_down = on ? 0x0 : 0x3;
- int rx_enable = on ? 0x3 : 0x1;
-
- rtl9300_sds_field_w(sds, 0x20, 0x00, 7, 6, power_down);
- rtl9300_sds_field_w(sds, 0x20, 0x00, 5, 4, rx_enable);
-}
-
-static int rtsds_930x_config_pll(int sds, phy_interface_t interface)
-{
- int neighbor_speed, neighbor_mode, neighbor_pll, neighbor = sds ^ 1;
- bool speed_changed = true;
- int pll, speed;
-
- /*
- * A SerDes pair on the RTL930x is driven by two PLLs. A low speed ring PLL can generate
- * signals of 1.25G and 3.125G for link speeds of 1G/2.5G. A high speed LC PLL can
- * additionally generate a 10.3125G signal for 10G speeds. To drive the pair at different
- * speeds each SerDes must use its own PLL. But what if the SerDess attached to the ring
- * PLL suddenly needs 10G but the LC PLL is running at 1G? To avoid reconfiguring the
- * "partner" SerDes we must choose wisely what assignment serves the current needs. The
- * logic boils down to the following rules:
- *
- * - Use ring PLL for slow 1G speeds
- * - Use LC PLL for fast 10G speeds
- * - For 2.5G prefer ring over LC PLL
- */
-
- neighbor_mode = rtsds_930x_get_internal_mode(neighbor);
- rtsds_930x_get_pll_data(neighbor, &neighbor_pll, &neighbor_speed);
-
- if ((interface == PHY_INTERFACE_MODE_1000BASEX) ||
- (interface == PHY_INTERFACE_MODE_SGMII))
- speed = RTSDS_930X_PLL_1000;
- else if (interface == PHY_INTERFACE_MODE_2500BASEX)
- speed = RTSDS_930X_PLL_2500;
- else if (interface == PHY_INTERFACE_MODE_10GBASER)
- speed = RTSDS_930X_PLL_10000;
- else
- return -ENOTSUPP;
-
- if (!neighbor_mode)
- pll = speed == RTSDS_930X_PLL_10000 ? RTSDS_930X_PLL_LC : RTSDS_930X_PLL_RING;
- else if (speed == neighbor_speed) {
- speed_changed = false;
- pll = neighbor_pll;
- } else if (neighbor_pll == RTSDS_930X_PLL_RING)
- pll = RTSDS_930X_PLL_LC;
- else if (speed == RTSDS_930X_PLL_10000)
- return -ENOTSUPP; /* caller wants 10G but only ring PLL available */
- else
- pll = RTSDS_930X_PLL_RING;
-
- rtsds_930x_set_pll_data(sds, pll, speed);
-
- if (speed_changed)
- rtsds_930x_reset_cmu(sds);
-
- pr_info("%s: SDS %d using %s PLL for %s\n", __func__, sds,
- pll == RTSDS_930X_PLL_LC ? "LC" : "ring", phy_modes(interface));
-
- return 0;
-}
-
-static void rtsds_930x_reset_state_machine(int sds)
-{
- rtl9300_sds_field_w(sds, 0x06, 0x02, 12, 12, 0x01); /* SM_RESET bit */
- usleep_range(10000, 20000);
- rtl9300_sds_field_w(sds, 0x06, 0x02, 12, 12, 0x00);
- usleep_range(10000, 20000);
-}
-
-static int rtsds_930x_init_state_machine(int sds, phy_interface_t interface)
-{
- int loopback, link, cnt = 20, ret = -EBUSY;
-
- if (interface != PHY_INTERFACE_MODE_10GBASER)
- return 0;
- /*
- * After a SerDes mode change it takes some time until the frontend state machine
- * works properly for 10G. To verify operation readyness run a connection check via
- * loopback.
- */
- loopback = rtl9300_sds_field_r(sds, 0x06, 0x01, 2, 2); /* CFG_AFE_LPK bit */
- rtl9300_sds_field_w(sds, 0x06, 0x01, 2, 2, 0x01);
-
- while (cnt-- && ret) {
- rtsds_930x_reset_state_machine(sds);
- link = rtl9300_sds_field_r(sds, 0x05, 0x00, 12, 12); /* 10G link state (latched) */
- link = rtl9300_sds_field_r(sds, 0x05, 0x00, 12, 12);
- if (link)
- ret = 0;
- }
-
- rtl9300_sds_field_w(sds, 0x06, 0x01, 2, 2, loopback);
- rtsds_930x_reset_state_machine(sds);
-
- return ret;
-}
-
-static void rtsds_930x_force_mode(int sds, phy_interface_t interface)
-{
- int mode;
-
- /*
- * TODO: Usually one would expect that it is enough to modify the SDS_MODE_SEL_*
- * registers (lets call it MAC setup). It seems as if this complex sequence is only
- * needed for modes that cannot be set by the SoC itself. Additionally it is unclear
- * if this sequence should quit early in case of errors.
- */
-
- switch (interface) {
- case PHY_INTERFACE_MODE_SGMII:
- mode = RTL930X_SDS_MODE_SGMII;
- break;
- case PHY_INTERFACE_MODE_1000BASEX:
- mode = RTL930X_SDS_MODE_1000BASEX;
- break;
- case PHY_INTERFACE_MODE_2500BASEX:
- mode = RTL930X_SDS_MODE_2500BASEX;
- break;
- case PHY_INTERFACE_MODE_10GBASER:
- mode = RTL930X_SDS_MODE_10GBASER;
- break;
- case PHY_INTERFACE_MODE_NA:
- mode = RTL930X_SDS_OFF;
- break;
- default:
- pr_err("%s: SDS %d does not support %s\n", __func__, sds, phy_modes(interface));
- return;
- }
-
- rtsds_930x_set_power(sds, false);
- rtsds_930x_set_internal_mode(sds, RTL930X_SDS_OFF);
- if (interface == PHY_INTERFACE_MODE_NA)
- return;
-
- if (rtsds_930x_config_pll(sds, interface))
- pr_err("%s: SDS %d could not configure PLL for %s\n", __func__,
- sds, phy_modes(interface));
-
- rtsds_930x_set_internal_mode(sds, mode);
- if (rtsds_930x_wait_clock_ready(sds))
- pr_err("%s: SDS %d could not sync clock\n", __func__, sds);
-
- if (rtsds_930x_init_state_machine(sds, interface))
- pr_err("%s: SDS %d could not reset state machine\n", __func__, sds);
-
- rtsds_930x_set_power(sds, true);
- rtl930x_sds_rx_rst(sds, interface);
-}
-
-static void rtsds_930x_mode_set(int sds, phy_interface_t phy_mode)
-{
- u32 mode;
- u32 submode;
-
- if (sds < 0 || sds > 11) {
- pr_err("%s: invalid SerDes number: %d\n", __func__, sds);
- return;
- }
-
- switch(phy_mode) {
- case PHY_INTERFACE_MODE_SGMII:
- case PHY_INTERFACE_MODE_1000BASEX:
- case PHY_INTERFACE_MODE_2500BASEX:
- case PHY_INTERFACE_MODE_10GBASER:
- rtsds_930x_force_mode(sds, phy_mode);
- return;
- case PHY_INTERFACE_MODE_10G_QXGMII:
- mode = RTL930X_SDS_MODE_USXGMII;
- submode = RTL930X_SDS_SUBMODE_USXGMII_QX;
- break;
- default:
- pr_warn("%s: unsupported mode %s\n", __func__, phy_modes(phy_mode));
- return;
- }
-
- /* SerDes off first. */
- rtl9300_sds_set(sds, RTL930X_SDS_OFF);
-
- /* Set the mode. */
- rtl9300_sds_set(sds, mode);
-
- /* Set the submode if needed. */
- if (phy_mode == PHY_INTERFACE_MODE_10G_QXGMII) {
- rtsds_930x_submode_set(sds, submode);
- }
-}
-
-
-static void rtl9300_sds_tx_config(int sds, phy_interface_t phy_if)
-{
- /* parameters: rtl9303_80G_txParam_s2 */
- int impedance = 0x8;
- int pre_amp = 0x2;
- int main_amp = 0x9;
- int post_amp = 0x2;
- int pre_en = 0x1;
- int post_en = 0x1;
- int page;
-
- switch(phy_if) {
- case PHY_INTERFACE_MODE_1000BASEX:
- case PHY_INTERFACE_MODE_SGMII:
- pre_amp = 0x1;
- main_amp = 0x9;
- post_amp = 0x1;
- page = 0x25;
- break;
- case PHY_INTERFACE_MODE_2500BASEX:
- pre_amp = 0;
- post_amp = 0x8;
- pre_en = 0;
- page = 0x29;
- break;
- case PHY_INTERFACE_MODE_10GBASER:
- case PHY_INTERFACE_MODE_USXGMII:
- case PHY_INTERFACE_MODE_10G_QXGMII:
- case PHY_INTERFACE_MODE_XGMII:
- pre_en = 0;
- pre_amp = 0;
- main_amp = 0x10;
- post_amp = 0;
- post_en = 0;
- page = 0x2f;
- break;
- default:
- pr_err("%s: unsupported PHY mode\n", __func__);
- return;
- }
-
- rtl9300_sds_field_w(sds, page, 0x01, 15, 11, pre_amp);
- rtl9300_sds_field_w(sds, page, 0x06, 4, 0, post_amp);
- rtl9300_sds_field_w(sds, page, 0x07, 0, 0, pre_en);
- rtl9300_sds_field_w(sds, page, 0x07, 3, 3, post_en);
- rtl9300_sds_field_w(sds, page, 0x07, 8, 4, main_amp);
- rtl9300_sds_field_w(sds, page, 0x18, 15, 12, impedance);
-}
-
-/* Wait for clock ready, this assumes the SerDes is in XGMII mode
- * timeout is in ms
- */
-int rtl9300_sds_clock_wait(int timeout)
-{
- u32 v;
- unsigned long start = jiffies;
-
- do {
- rtl9300_sds_field_w(2, 0x1f, 0x2, 15, 0, 53);
- v = rtl9300_sds_field_r(2, 0x1f, 20, 5, 4);
- if (v == 3)
- return 0;
- } while (jiffies < start + (HZ / 1000) * timeout);
-
- return 1;
-}
-
-static void rtl9300_serdes_mac_link_config(int sds, bool tx_normal, bool rx_normal)
-{
- u32 v10, v1;
-
- v10 = rtmdio_930x_read_sds_phy(sds, 6, 2); /* 10GBit, page 6, reg 2 */
- v1 = rtmdio_930x_read_sds_phy(sds, 0, 0); /* 1GBit, page 0, reg 0 */
- pr_info("%s: registers before %08x %08x\n", __func__, v10, v1);
-
- v10 &= ~(BIT(13) | BIT(14));
- v1 &= ~(BIT(8) | BIT(9));
-
- v10 |= rx_normal ? 0 : BIT(13);
- v1 |= rx_normal ? 0 : BIT(9);
-
- v10 |= tx_normal ? 0 : BIT(14);
- v1 |= tx_normal ? 0 : BIT(8);
-
- rtmdio_930x_write_sds_phy(sds, 6, 2, v10);
- rtmdio_930x_write_sds_phy(sds, 0, 0, v1);
-
- v10 = rtmdio_930x_read_sds_phy(sds, 6, 2);
- v1 = rtmdio_930x_read_sds_phy(sds, 0, 0);
- pr_info("%s: registers after %08x %08x\n", __func__, v10, v1);
-}
-
-void rtl9300_sds_rxcal_dcvs_manual(u32 sds_num, u32 dcvs_id, bool manual, u32 dvcs_list[])
-{
- if (manual) {
- switch(dcvs_id) {
- case 0:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 14, 14, 0x1);
- rtl9300_sds_field_w(sds_num, 0x2f, 0x03, 5, 5, dvcs_list[0]);
- rtl9300_sds_field_w(sds_num, 0x2f, 0x03, 4, 0, dvcs_list[1]);
- break;
- case 1:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 13, 13, 0x1);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1d, 15, 15, dvcs_list[0]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1d, 14, 11, dvcs_list[1]);
- break;
- case 2:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 12, 12, 0x1);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1d, 10, 10, dvcs_list[0]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1d, 9, 6, dvcs_list[1]);
- break;
- case 3:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 11, 11, 0x1);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1d, 5, 5, dvcs_list[0]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1d, 4, 1, dvcs_list[1]);
- break;
- case 4:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x01, 15, 15, 0x1);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x11, 10, 10, dvcs_list[0]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x11, 9, 6, dvcs_list[1]);
- break;
- case 5:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x02, 11, 11, 0x1);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x11, 4, 4, dvcs_list[0]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x11, 3, 0, dvcs_list[1]);
- break;
- default:
- break;
- }
- } else {
- switch(dcvs_id) {
- case 0:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 14, 14, 0x0);
- break;
- case 1:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 13, 13, 0x0);
- break;
- case 2:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 12, 12, 0x0);
- break;
- case 3:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 11, 11, 0x0);
- break;
- case 4:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x01, 15, 15, 0x0);
- break;
- case 5:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x02, 11, 11, 0x0);
- break;
- default:
- break;
- }
- mdelay(1);
- }
-}
-
-void rtl9300_sds_rxcal_dcvs_get(u32 sds_num, u32 dcvs_id, u32 dcvs_list[])
-{
- u32 dcvs_sign_out = 0, dcvs_coef_bin = 0;
- bool dcvs_manual;
-
- if (!(sds_num % 2))
- rtmdio_930x_write_sds_phy(sds_num, 0x1f, 0x2, 0x2f);
- else
- rtmdio_930x_write_sds_phy(sds_num - 1, 0x1f, 0x2, 0x31);
-
- /* ##Page0x2E, Reg0x15[9], REG0_RX_EN_TEST=[1] */
- rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 9, 9, 0x1);
-
- /* ##Page0x21, Reg0x06[11 6], REG0_RX_DEBUG_SEL=[1 0 x x x x] */
- rtl9300_sds_field_w(sds_num, 0x21, 0x06, 11, 6, 0x20);
-
- switch(dcvs_id) {
- case 0:
- rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0x22);
- mdelay(1);
-
- /* ##DCVS0 Read Out */
- dcvs_sign_out = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 4);
- dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 3, 0);
- dcvs_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x1e, 14, 14);
- break;
-
- case 1:
- rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0x23);
- mdelay(1);
-
- /* ##DCVS0 Read Out */
- dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 4);
- dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 3, 0);
- dcvs_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x1e, 13, 13);
- break;
-
- case 2:
- rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0x24);
- mdelay(1);
-
- /* ##DCVS0 Read Out */
- dcvs_sign_out = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 4);
- dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 3, 0);
- dcvs_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x1e, 12, 12);
- break;
- case 3:
- rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0x25);
- mdelay(1);
-
- /* ##DCVS0 Read Out */
- dcvs_sign_out = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 4);
- dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 3, 0);
- dcvs_manual = rtl9300_sds_field_r(sds_num, 0x2e, 0x1e, 11, 11);
- break;
-
- case 4:
- rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0x2c);
- mdelay(1);
-
- /* ##DCVS0 Read Out */
- dcvs_sign_out = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 4);
- dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 3, 0);
- dcvs_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x01, 15, 15);
- break;
-
- case 5:
- rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0x2d);
- mdelay(1);
-
- /* ##DCVS0 Read Out */
- dcvs_sign_out = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 4);
- dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 3, 0);
- dcvs_manual = rtl9300_sds_field_r(sds_num, 0x2e, 0x02, 11, 11);
- break;
-
- default:
- break;
- }
-
- if (dcvs_sign_out)
- pr_info("%s DCVS %u Sign: -", __func__, dcvs_id);
- else
- pr_info("%s DCVS %u Sign: +", __func__, dcvs_id);
-
- pr_info("DCVS %u even coefficient = %u", dcvs_id, dcvs_coef_bin);
- pr_info("DCVS %u manual = %u", dcvs_id, dcvs_manual);
-
- dcvs_list[0] = dcvs_sign_out;
- dcvs_list[1] = dcvs_coef_bin;
-}
-
-static void rtl9300_sds_rxcal_leq_manual(u32 sds_num, bool manual, u32 leq_gray)
-{
- if (manual) {
- rtl9300_sds_field_w(sds_num, 0x2e, 0x18, 15, 15, 0x1);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x16, 14, 10, leq_gray);
- } else {
- rtl9300_sds_field_w(sds_num, 0x2e, 0x18, 15, 15, 0x0);
- mdelay(100);
- }
-}
-
-static void rtl9300_sds_rxcal_leq_offset_manual(u32 sds_num, bool manual, u32 offset)
-{
- if (manual) {
- rtl9300_sds_field_w(sds_num, 0x2e, 0x17, 6, 2, offset);
- } else {
- rtl9300_sds_field_w(sds_num, 0x2e, 0x17, 6, 2, offset);
- mdelay(1);
- }
-}
-
-#define GRAY_BITS 5
-static u32 rtl9300_sds_rxcal_gray_to_binary(u32 gray_code)
-{
- int i, j, m;
- u32 g[GRAY_BITS];
- u32 c[GRAY_BITS];
- u32 leq_binary = 0;
-
- for(i = 0; i < GRAY_BITS; i++)
- g[i] = (gray_code & BIT(i)) >> i;
-
- m = GRAY_BITS - 1;
-
- c[m] = g[m];
-
- for(i = 0; i < m; i++) {
- c[i] = g[i];
- for(j = i + 1; j < GRAY_BITS; j++)
- c[i] = c[i] ^ g[j];
- }
-
- for(i = 0; i < GRAY_BITS; i++)
- leq_binary += c[i] << i;
-
- return leq_binary;
-}
-
-static u32 rtl9300_sds_rxcal_leq_read(int sds_num)
-{
- u32 leq_gray, leq_bin;
- bool leq_manual;
-
- if (!(sds_num % 2))
- rtmdio_930x_write_sds_phy(sds_num, 0x1f, 0x2, 0x2f);
- else
- rtmdio_930x_write_sds_phy(sds_num - 1, 0x1f, 0x2, 0x31);
-
- /* ##Page0x2E, Reg0x15[9], REG0_RX_EN_TEST=[1] */
- rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 9, 9, 0x1);
-
- /* ##Page0x21, Reg0x06[11 6], REG0_RX_DEBUG_SEL=[0 1 x x x x] */
- rtl9300_sds_field_w(sds_num, 0x21, 0x06, 11, 6, 0x10);
- mdelay(1);
-
- /* ##LEQ Read Out */
- leq_gray = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 7, 3);
- leq_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x18, 15, 15);
- leq_bin = rtl9300_sds_rxcal_gray_to_binary(leq_gray);
-
- pr_info("LEQ_gray: %u, LEQ_bin: %u", leq_gray, leq_bin);
- pr_info("LEQ manual: %u", leq_manual);
-
- return leq_bin;
-}
-
-static void rtl9300_sds_rxcal_vth_manual(u32 sds_num, bool manual, u32 vth_list[])
-{
- if (manual) {
- rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, 13, 13, 0x1);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x13, 5, 3, vth_list[0]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x13, 2, 0, vth_list[1]);
- } else {
- rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, 13, 13, 0x0);
- mdelay(10);
- }
-}
-
-static void rtl9300_sds_rxcal_vth_get(u32 sds_num, u32 vth_list[])
-{
- u32 vth_manual;
-
- /* ##Page0x1F, Reg0x02[15 0], REG_DBGO_SEL=[0x002F]; */ /* Lane0 */
- /* ##Page0x1F, Reg0x02[15 0], REG_DBGO_SEL=[0x0031]; */ /* Lane1 */
- if (!(sds_num % 2))
- rtmdio_930x_write_sds_phy(sds_num, 0x1f, 0x2, 0x2f);
- else
- rtmdio_930x_write_sds_phy(sds_num - 1, 0x1f, 0x2, 0x31);
-
- /* ##Page0x2E, Reg0x15[9], REG0_RX_EN_TEST=[1] */
- rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 9, 9, 0x1);
- /* ##Page0x21, Reg0x06[11 6], REG0_RX_DEBUG_SEL=[1 0 x x x x] */
- rtl9300_sds_field_w(sds_num, 0x21, 0x06, 11, 6, 0x20);
- /* ##Page0x2F, Reg0x0C[5 0], REG0_COEF_SEL=[0 0 1 1 0 0] */
- rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0xc);
-
- mdelay(1);
-
- /* ##VthP & VthN Read Out */
- vth_list[0] = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 2, 0); /* v_thp set bin */
- vth_list[1] = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 5, 3); /* v_thn set bin */
-
- pr_info("vth_set_bin = %d", vth_list[0]);
- pr_info("vth_set_bin = %d", vth_list[1]);
-
- vth_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x0f, 13, 13);
- pr_info("Vth Maunal = %d", vth_manual);
-}
-
-static void rtl9300_sds_rxcal_tap_manual(u32 sds_num, int tap_id, bool manual, u32 tap_list[])
-{
- if (manual) {
- switch(tap_id) {
- case 0:
- /* ##REG0_LOAD_IN_INIT[0]=1; REG0_TAP0_INIT[5:0]=Tap0_Value */
- rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7, 0x1);
- rtl9300_sds_field_w(sds_num, 0x2f, 0x03, 5, 5, tap_list[0]);
- rtl9300_sds_field_w(sds_num, 0x2f, 0x03, 4, 0, tap_list[1]);
- break;
- case 1:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7, 0x1);
- rtl9300_sds_field_w(sds_num, 0x21, 0x07, 6, 6, tap_list[0]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x09, 11, 6, tap_list[1]);
- rtl9300_sds_field_w(sds_num, 0x21, 0x07, 5, 5, tap_list[2]);
- rtl9300_sds_field_w(sds_num, 0x2f, 0x12, 5, 0, tap_list[3]);
- break;
- case 2:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7, 0x1);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x09, 5, 5, tap_list[0]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x09, 4, 0, tap_list[1]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x0a, 11, 11, tap_list[2]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x0a, 10, 6, tap_list[3]);
- break;
- case 3:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7, 0x1);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x0a, 5, 5, tap_list[0]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x0a, 4, 0, tap_list[1]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x06, 5, 5, tap_list[2]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x06, 4, 0, tap_list[3]);
- break;
- case 4:
- rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7, 0x1);
- rtl9300_sds_field_w(sds_num, 0x2f, 0x01, 5, 5, tap_list[0]);
- rtl9300_sds_field_w(sds_num, 0x2f, 0x01, 4, 0, tap_list[1]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x06, 11, 11, tap_list[2]);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x06, 10, 6, tap_list[3]);
- break;
- default:
- break;
- }
- } else {
- rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7, 0x0);
- mdelay(10);
- }
-}
-
-static void rtl9300_sds_rxcal_tap_get(u32 sds_num, u32 tap_id, u32 tap_list[])
-{
- u32 tap0_sign_out;
- u32 tap0_coef_bin;
- u32 tap_sign_out_even;
- u32 tap_coef_bin_even;
- u32 tap_sign_out_odd;
- u32 tap_coef_bin_odd;
- bool tap_manual;
-
- if (!(sds_num % 2))
- rtmdio_930x_write_sds_phy(sds_num, 0x1f, 0x2, 0x2f);
- else
- rtmdio_930x_write_sds_phy(sds_num - 1, 0x1f, 0x2, 0x31);
-
- /* ##Page0x2E, Reg0x15[9], REG0_RX_EN_TEST=[1] */
- rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 9, 9, 0x1);
- /* ##Page0x21, Reg0x06[11 6], REG0_RX_DEBUG_SEL=[1 0 x x x x] */
- rtl9300_sds_field_w(sds_num, 0x21, 0x06, 11, 6, 0x20);
-
- if (!tap_id) {
- /* ##Page0x2F, Reg0x0C[5 0], REG0_COEF_SEL=[0 0 0 0 0 1] */
- rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0);
- /* ##Tap1 Even Read Out */
- mdelay(1);
- tap0_sign_out = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 5, 5);
- tap0_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 0);
-
- if (tap0_sign_out == 1)
- pr_info("Tap0 Sign : -");
- else
- pr_info("Tap0 Sign : +");
-
- pr_info("tap0_coef_bin = %d", tap0_coef_bin);
-
- tap_list[0] = tap0_sign_out;
- tap_list[1] = tap0_coef_bin;
-
- tap_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x0f, 7, 7);
- pr_info("tap0 manual = %u",tap_manual);
- } else {
- /* ##Page0x2F, Reg0x0C[5 0], REG0_COEF_SEL=[0 0 0 0 0 1] */
- rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, tap_id);
- mdelay(1);
- /* ##Tap1 Even Read Out */
- tap_sign_out_even = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 5, 5);
- tap_coef_bin_even = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 0);
-
- /* ##Page0x2F, Reg0x0C[5 0], REG0_COEF_SEL=[0 0 0 1 1 0] */
- rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, (tap_id + 5));
- /* ##Tap1 Odd Read Out */
- tap_sign_out_odd = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 5, 5);
- tap_coef_bin_odd = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 0);
-
- if (tap_sign_out_even == 1)
- pr_info("Tap %u even sign: -", tap_id);
- else
- pr_info("Tap %u even sign: +", tap_id);
-
- pr_info("Tap %u even coefficient = %u", tap_id, tap_coef_bin_even);
-
- if (tap_sign_out_odd == 1)
- pr_info("Tap %u odd sign: -", tap_id);
- else
- pr_info("Tap %u odd sign: +", tap_id);
-
- pr_info("Tap %u odd coefficient = %u", tap_id,tap_coef_bin_odd);
-
- tap_list[0] = tap_sign_out_even;
- tap_list[1] = tap_coef_bin_even;
- tap_list[2] = tap_sign_out_odd;
- tap_list[3] = tap_coef_bin_odd;
-
- tap_manual = rtl9300_sds_field_r(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7);
- pr_info("tap %u manual = %d",tap_id, tap_manual);
- }
-}
-
-static void rtl9300_do_rx_calibration_1(int sds, phy_interface_t phy_mode)
-{
- /* From both rtl9300_rxCaliConf_serdes_myParam and rtl9300_rxCaliConf_phy_myParam */
- int tap0_init_val = 0x1f; /* Initial Decision Fed Equalizer 0 tap */
- int vth_min = 0x0;
-
- pr_info("start_1.1.1 initial value for sds %d\n", sds);
- rtmdio_930x_write_sds_phy(sds, 6, 0, 0);
-
- /* FGCAL */
- rtl9300_sds_field_w(sds, 0x2e, 0x01, 14, 14, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x1c, 10, 5, 0x20);
- rtl9300_sds_field_w(sds, 0x2f, 0x02, 0, 0, 0x01);
-
- /* DCVS */
- rtl9300_sds_field_w(sds, 0x2e, 0x1e, 14, 11, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x01, 15, 15, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x02, 11, 11, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x1c, 4, 0, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x1d, 15, 11, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x1d, 10, 6, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x1d, 5, 1, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x02, 10, 6, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x11, 4, 0, 0x00);
- rtl9300_sds_field_w(sds, 0x2f, 0x00, 3, 0, 0x0f);
- rtl9300_sds_field_w(sds, 0x2e, 0x04, 6, 6, 0x01);
- rtl9300_sds_field_w(sds, 0x2e, 0x04, 7, 7, 0x01);
-
- /* LEQ (Long Term Equivalent signal level) */
- rtl9300_sds_field_w(sds, 0x2e, 0x16, 14, 8, 0x00);
-
- /* DFE (Decision Fed Equalizer) */
- rtl9300_sds_field_w(sds, 0x2f, 0x03, 5, 0, tap0_init_val);
- rtl9300_sds_field_w(sds, 0x2e, 0x09, 11, 6, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x09, 5, 0, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x0a, 5, 0, 0x00);
- rtl9300_sds_field_w(sds, 0x2f, 0x01, 5, 0, 0x00);
- rtl9300_sds_field_w(sds, 0x2f, 0x12, 5, 0, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x0a, 11, 6, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x06, 5, 0, 0x00);
- rtl9300_sds_field_w(sds, 0x2f, 0x01, 5, 0, 0x00);
-
- /* Vth */
- rtl9300_sds_field_w(sds, 0x2e, 0x13, 5, 3, 0x07);
- rtl9300_sds_field_w(sds, 0x2e, 0x13, 2, 0, 0x07);
- rtl9300_sds_field_w(sds, 0x2f, 0x0b, 5, 3, vth_min);
-
- pr_info("end_1.1.1 --\n");
-
- pr_info("start_1.1.2 Load DFE init. value\n");
-
- rtl9300_sds_field_w(sds, 0x2e, 0x0f, 13, 7, 0x7f);
-
- pr_info("end_1.1.2\n");
-
- pr_info("start_1.1.3 disable LEQ training,enable DFE clock\n");
-
- rtl9300_sds_field_w(sds, 0x2e, 0x17, 7, 7, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x17, 6, 2, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x0c, 8, 8, 0x00);
- rtl9300_sds_field_w(sds, 0x2e, 0x0b, 4, 4, 0x01);
- rtl9300_sds_field_w(sds, 0x2e, 0x12, 14, 14, 0x00);
- rtl9300_sds_field_w(sds, 0x2f, 0x02, 15, 15, 0x00);
-
- pr_info("end_1.1.3 --\n");
-
- pr_info("start_1.1.4 offset cali setting\n");
-
- rtl9300_sds_field_w(sds, 0x2e, 0x0f, 15, 14, 0x03);
-
- pr_info("end_1.1.4\n");
-
- pr_info("start_1.1.5 LEQ and DFE setting\n");
-
- /* TODO: make this work for DAC cables of different lengths */
- /* For a 10GBit serdes wit Fibre, SDS 8 or 9 */
- if (phy_mode == PHY_INTERFACE_MODE_10GBASER ||
- phy_mode == PHY_INTERFACE_MODE_1000BASEX ||
- phy_mode == PHY_INTERFACE_MODE_SGMII)
- rtl9300_sds_field_w(sds, 0x2e, 0x16, 3, 2, 0x02);
- else
- pr_err("%s not PHY-based or SerDes, implement DAC!\n", __func__);
-
- /* No serdes, check for Aquantia PHYs */
- rtl9300_sds_field_w(sds, 0x2e, 0x16, 3, 2, 0x02);
-
- rtl9300_sds_field_w(sds, 0x2e, 0x0f, 6, 0, 0x5f);
- rtl9300_sds_field_w(sds, 0x2f, 0x05, 7, 2, 0x1f);
- rtl9300_sds_field_w(sds, 0x2e, 0x19, 9, 5, 0x1f);
- rtl9300_sds_field_w(sds, 0x2f, 0x0b, 15, 9, 0x3c);
- rtl9300_sds_field_w(sds, 0x2e, 0x0b, 1, 0, 0x03);
-
- pr_info("end_1.1.5\n");
-}
-
-static void rtl9300_do_rx_calibration_2_1(u32 sds_num)
-{
- pr_info("start_1.2.1 ForegroundOffsetCal_Manual\n");
-
- /* Gray config endis to 1 */
- rtl9300_sds_field_w(sds_num, 0x2f, 0x02, 2, 2, 0x01);
-
- /* ForegroundOffsetCal_Manual(auto mode) */
- rtl9300_sds_field_w(sds_num, 0x2e, 0x01, 14, 14, 0x00);
-
- pr_info("end_1.2.1");
-}
-
-static void rtl9300_do_rx_calibration_2_2(int sds_num)
-{
- /* Force Rx-Run = 0 */
- rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 8, 8, 0x0);
-
- rtl930x_sds_rx_rst(sds_num, PHY_INTERFACE_MODE_10GBASER);
-}
-
-static void rtl9300_do_rx_calibration_2_3(int sds_num)
-{
- u32 fgcal_binary, fgcal_gray;
- u32 offset_range;
-
- pr_info("start_1.2.3 Foreground Calibration\n");
-
- while(1) {
- if (!(sds_num % 2))
- rtmdio_930x_write_sds_phy(sds_num, 0x1f, 0x2, 0x2f);
- else
- rtmdio_930x_write_sds_phy(sds_num -1 , 0x1f, 0x2, 0x31);
-
- /* ##Page0x2E, Reg0x15[9], REG0_RX_EN_TEST=[1] */
- rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 9, 9, 0x1);
- /* ##Page0x21, Reg0x06[11 6], REG0_RX_DEBUG_SEL=[1 0 x x x x] */
- rtl9300_sds_field_w(sds_num, 0x21, 0x06, 11, 6, 0x20);
- /* ##Page0x2F, Reg0x0C[5 0], REG0_COEF_SEL=[0 0 1 1 1 1] */
- rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0xf);
- /* ##FGCAL read gray */
- fgcal_gray = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 5, 0);
- /* ##Page0x2F, Reg0x0C[5 0], REG0_COEF_SEL=[0 0 1 1 1 0] */
- rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0xe);
- /* ##FGCAL read binary */
- fgcal_binary = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 5, 0);
-
- pr_info("%s: fgcal_gray: %d, fgcal_binary %d\n",
- __func__, fgcal_gray, fgcal_binary);
-
- offset_range = rtl9300_sds_field_r(sds_num, 0x2e, 0x15, 15, 14);
-
- if (fgcal_binary > 60 || fgcal_binary < 3) {
- if (offset_range == 3) {
- pr_info("%s: Foreground Calibration result marginal!", __func__);
- break;
- } else {
- offset_range++;
- rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 15, 14, offset_range);
- rtl9300_do_rx_calibration_2_2(sds_num);
- }
- } else {
- break;
- }
- }
- pr_info("%s: end_1.2.3\n", __func__);
-}
-
-static void rtl9300_do_rx_calibration_2(int sds)
-{
- rtl930x_sds_rx_rst(sds, PHY_INTERFACE_MODE_10GBASER);
- rtl9300_do_rx_calibration_2_1(sds);
- rtl9300_do_rx_calibration_2_2(sds);
- rtl9300_do_rx_calibration_2_3(sds);
-}
-
-static void rtl9300_sds_rxcal_3_1(int sds_num, phy_interface_t phy_mode)
-{
- pr_info("start_1.3.1");
-
- /* ##1.3.1 */
- if (phy_mode != PHY_INTERFACE_MODE_10GBASER &&
- phy_mode != PHY_INTERFACE_MODE_1000BASEX &&
- phy_mode != PHY_INTERFACE_MODE_SGMII)
- rtl9300_sds_field_w(sds_num, 0x2e, 0xc, 8, 8, 0);
-
- rtl9300_sds_field_w(sds_num, 0x2e, 0x17, 7, 7, 0x0);
- rtl9300_sds_rxcal_leq_manual(sds_num, false, 0);
-
- pr_info("end_1.3.1");
-}
-
-static void rtl9300_sds_rxcal_3_2(int sds_num, phy_interface_t phy_mode)
-{
- u32 sum10 = 0, avg10, int10;
- int dac_long_cable_offset;
- bool eq_hold_enabled;
- int i;
-
- if (phy_mode == PHY_INTERFACE_MODE_10GBASER ||
- phy_mode == PHY_INTERFACE_MODE_1000BASEX ||
- phy_mode == PHY_INTERFACE_MODE_SGMII) {
- /* rtl9300_rxCaliConf_serdes_myParam */
- dac_long_cable_offset = 3;
- eq_hold_enabled = true;
- } else {
- /* rtl9300_rxCaliConf_phy_myParam */
- dac_long_cable_offset = 0;
- eq_hold_enabled = false;
- }
-
- if (phy_mode != PHY_INTERFACE_MODE_10GBASER)
- pr_warn("%s: LEQ only valid for 10GR!\n", __func__);
-
- pr_info("start_1.3.2");
-
- for(i = 0; i < 10; i++) {
- sum10 += rtl9300_sds_rxcal_leq_read(sds_num);
- mdelay(10);
- }
-
- avg10 = (sum10 / 10) + (((sum10 % 10) >= 5) ? 1 : 0);
- int10 = sum10 / 10;
-
- pr_info("sum10:%u, avg10:%u, int10:%u", sum10, avg10, int10);
-
- if (phy_mode == PHY_INTERFACE_MODE_10GBASER ||
- phy_mode == PHY_INTERFACE_MODE_1000BASEX ||
- phy_mode == PHY_INTERFACE_MODE_SGMII) {
- if (dac_long_cable_offset) {
- rtl9300_sds_rxcal_leq_offset_manual(sds_num, 1, dac_long_cable_offset);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x17, 7, 7, eq_hold_enabled);
- if (phy_mode == PHY_INTERFACE_MODE_10GBASER)
- rtl9300_sds_rxcal_leq_manual(sds_num, true, avg10);
- } else {
- if (sum10 >= 5) {
- rtl9300_sds_rxcal_leq_offset_manual(sds_num, 1, 3);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x17, 7, 7, 0x1);
- if (phy_mode == PHY_INTERFACE_MODE_10GBASER)
- rtl9300_sds_rxcal_leq_manual(sds_num, true, avg10);
- } else {
- rtl9300_sds_rxcal_leq_offset_manual(sds_num, 1, 0);
- rtl9300_sds_field_w(sds_num, 0x2e, 0x17, 7, 7, 0x1);
- if (phy_mode == PHY_INTERFACE_MODE_10GBASER)
- rtl9300_sds_rxcal_leq_manual(sds_num, true, avg10);
- }
- }
- }
-
- pr_info("Sds:%u LEQ = %u",sds_num, rtl9300_sds_rxcal_leq_read(sds_num));
-
- pr_info("end_1.3.2");
-}
-
-void rtl9300_do_rx_calibration_3(int sds_num, phy_interface_t phy_mode)
-{
- rtl9300_sds_rxcal_3_1(sds_num, phy_mode);
-
- if (phy_mode == PHY_INTERFACE_MODE_10GBASER ||
- phy_mode == PHY_INTERFACE_MODE_1000BASEX ||
- phy_mode == PHY_INTERFACE_MODE_SGMII)
- rtl9300_sds_rxcal_3_2(sds_num, phy_mode);
-}
-
-static void rtl9300_do_rx_calibration_4_1(int sds_num)
-{
- u32 vth_list[2] = {0, 0};
- u32 tap0_list[4] = {0, 0, 0, 0};
-
- pr_info("start_1.4.1");
-
- /* ##1.4.1 */
- rtl9300_sds_rxcal_vth_manual(sds_num, false, vth_list);
- rtl9300_sds_rxcal_tap_manual(sds_num, 0, false, tap0_list);
- mdelay(200);
-
- pr_info("end_1.4.1");
-}
-
-static void rtl9300_do_rx_calibration_4_2(u32 sds_num)
-{
- u32 vth_list[2];
- u32 tap_list[4];
-
- pr_info("start_1.4.2");
-
- rtl9300_sds_rxcal_vth_get(sds_num, vth_list);
- rtl9300_sds_rxcal_vth_manual(sds_num, true, vth_list);
-
- mdelay(100);
-
- rtl9300_sds_rxcal_tap_get(sds_num, 0, tap_list);
- rtl9300_sds_rxcal_tap_manual(sds_num, 0, true, tap_list);
-
- pr_info("end_1.4.2");
-}
-
-static void rtl9300_do_rx_calibration_4(u32 sds_num)
-{
- rtl9300_do_rx_calibration_4_1(sds_num);
- rtl9300_do_rx_calibration_4_2(sds_num);
-}
-
-static void rtl9300_do_rx_calibration_5_2(u32 sds_num)
-{
- u32 tap1_list[4] = {0};
- u32 tap2_list[4] = {0};
- u32 tap3_list[4] = {0};
- u32 tap4_list[4] = {0};
-
- pr_info("start_1.5.2");
-
- rtl9300_sds_rxcal_tap_manual(sds_num, 1, false, tap1_list);
- rtl9300_sds_rxcal_tap_manual(sds_num, 2, false, tap2_list);
- rtl9300_sds_rxcal_tap_manual(sds_num, 3, false, tap3_list);
- rtl9300_sds_rxcal_tap_manual(sds_num, 4, false, tap4_list);
-
- mdelay(30);
-
- pr_info("end_1.5.2");
-}
-
-static void rtl9300_do_rx_calibration_5(u32 sds_num, phy_interface_t phy_mode)
-{
- if (phy_mode == PHY_INTERFACE_MODE_10GBASER) /* dfeTap1_4Enable true */
- rtl9300_do_rx_calibration_5_2(sds_num);
-}
-
-
-static void rtl9300_do_rx_calibration_dfe_disable(u32 sds_num)
-{
- u32 tap1_list[4] = {0};
- u32 tap2_list[4] = {0};
- u32 tap3_list[4] = {0};
- u32 tap4_list[4] = {0};
-
- rtl9300_sds_rxcal_tap_manual(sds_num, 1, true, tap1_list);
- rtl9300_sds_rxcal_tap_manual(sds_num, 2, true, tap2_list);
- rtl9300_sds_rxcal_tap_manual(sds_num, 3, true, tap3_list);
- rtl9300_sds_rxcal_tap_manual(sds_num, 4, true, tap4_list);
-
- mdelay(10);
-}
-
-static void rtl9300_do_rx_calibration(int sds, phy_interface_t phy_mode)
-{
- u32 latch_sts;
-
- rtl9300_do_rx_calibration_1(sds, phy_mode);
- rtl9300_do_rx_calibration_2(sds);
- rtl9300_do_rx_calibration_4(sds);
- rtl9300_do_rx_calibration_5(sds, phy_mode);
- mdelay(20);
-
- /* Do this only for 10GR mode, SDS active in mode 0x1a */
- if (rtl9300_sds_field_r(sds, 0x1f, 9, 11, 7) == RTL930X_SDS_MODE_10GBASER) {
- pr_info("%s: SDS enabled\n", __func__);
- latch_sts = rtl9300_sds_field_r(sds, 0x4, 1, 2, 2);
- mdelay(1);
- latch_sts = rtl9300_sds_field_r(sds, 0x4, 1, 2, 2);
- if (latch_sts) {
- rtl9300_do_rx_calibration_dfe_disable(sds);
- rtl9300_do_rx_calibration_4(sds);
- rtl9300_do_rx_calibration_5(sds, phy_mode);
- }
- }
-}
-
-static int rtl9300_sds_sym_err_reset(int sds_num, phy_interface_t phy_mode)
-{
- switch (phy_mode) {
- case PHY_INTERFACE_MODE_XGMII:
- break;
-
- case PHY_INTERFACE_MODE_10GBASER:
- /* Read twice to clear */
- rtmdio_930x_read_sds_phy(sds_num, 5, 1);
- rtmdio_930x_read_sds_phy(sds_num, 5, 1);
- break;
-
- case PHY_INTERFACE_MODE_1000BASEX:
- case PHY_INTERFACE_MODE_SGMII:
- case PHY_INTERFACE_MODE_10G_QXGMII:
- rtl9300_sds_field_w(sds_num, 0x1, 24, 2, 0, 0);
- rtl9300_sds_field_w(sds_num, 0x1, 3, 15, 8, 0);
- rtl9300_sds_field_w(sds_num, 0x1, 2, 15, 0, 0);
- break;
-
- default:
- pr_info("%s unsupported phy mode\n", __func__);
- return -1;
- }
-
- return 0;
-}
-
-static u32 rtl9300_sds_sym_err_get(int sds_num, phy_interface_t phy_mode)
-{
- u32 v = 0;
-
- switch (phy_mode) {
- case PHY_INTERFACE_MODE_XGMII:
- case PHY_INTERFACE_MODE_10G_QXGMII:
- break;
-
- case PHY_INTERFACE_MODE_1000BASEX:
- case PHY_INTERFACE_MODE_SGMII:
- case PHY_INTERFACE_MODE_10GBASER:
- v = rtmdio_930x_read_sds_phy(sds_num, 5, 1);
- return v & 0xff;
-
- default:
- pr_info("%s unsupported PHY-mode\n", __func__);
- }
-
- return v;
-}
-
-static int rtl9300_sds_check_calibration(int sds_num, phy_interface_t phy_mode)
-{
- u32 errors1, errors2;
-
- rtl9300_sds_sym_err_reset(sds_num, phy_mode);
- rtl9300_sds_sym_err_reset(sds_num, phy_mode);
-
- /* Count errors during 1ms */
- errors1 = rtl9300_sds_sym_err_get(sds_num, phy_mode);
- mdelay(1);
- errors2 = rtl9300_sds_sym_err_get(sds_num, phy_mode);
-
- switch (phy_mode) {
- case PHY_INTERFACE_MODE_1000BASEX:
- case PHY_INTERFACE_MODE_SGMII:
- case PHY_INTERFACE_MODE_XGMII:
- if ((errors2 - errors1 > 100) ||
- (errors1 >= 0xffff00) || (errors2 >= 0xffff00)) {
- pr_info("%s XSGMII error rate too high\n", __func__);
- return 1;
- }
- break;
- case PHY_INTERFACE_MODE_10GBASER:
- case PHY_INTERFACE_MODE_10G_QXGMII:
- if (errors2 > 0) {
- pr_info("%s: %s error rate too high\n", __func__, phy_modes(phy_mode));
- return 1;
- }
- break;
- default:
- return 1;
- }
-
- return 0;
-}
-
-static void rtl9300_phy_enable_10g_1g(int sds_num)
-{
- u32 v;
-
- /* Enable 1GBit PHY */
- v = rtmdio_930x_read_sds_phy(sds_num, PHY_PAGE_2, MII_BMCR);
- pr_info("%s 1gbit phy: %08x\n", __func__, v);
- v &= ~BMCR_PDOWN;
- rtmdio_930x_write_sds_phy(sds_num, PHY_PAGE_2, MII_BMCR, v);
- pr_info("%s 1gbit phy enabled: %08x\n", __func__, v);
-
- /* Enable 10GBit PHY */
- v = rtmdio_930x_read_sds_phy(sds_num, PHY_PAGE_4, MII_BMCR);
- pr_info("%s 10gbit phy: %08x\n", __func__, v);
- v &= ~BMCR_PDOWN;
- rtmdio_930x_write_sds_phy(sds_num, PHY_PAGE_4, MII_BMCR, v);
- pr_info("%s 10gbit phy after: %08x\n", __func__, v);
-
- /* dal_longan_construct_mac_default_10gmedia_fiber */
- v = rtmdio_930x_read_sds_phy(sds_num, 0x1f, 11);
- pr_info("%s set medium: %08x\n", __func__, v);
- v |= BIT(1);
- rtmdio_930x_write_sds_phy(sds_num, 0x1f, 11, v);
- pr_info("%s set medium after: %08x\n", __func__, v);
-}
-
-static int rtl9300_sds_10g_idle(int sds_num);
-static void rtsds_930x_patch_serdes(int sds, phy_interface_t mode);
-
-#define RTL930X_MAC_FORCE_MODE_CTRL (0xCA1C)
-int rtl9300_serdes_setup(int port, int sds_num, phy_interface_t phy_mode)
-{
- int calib_tries = 0;
-
- /* Turn Off Serdes */
- rtl9300_sds_set(sds_num, RTL930X_SDS_OFF);
-
- /* Apply serdes patches */
- rtsds_930x_patch_serdes(sds_num, phy_mode);
-
- /* Maybe use dal_longan_sds_init */
-
- /* dal_longan_construct_serdesConfig_init */ /* Serdes Construct */
- rtl9300_phy_enable_10g_1g(sds_num);
-
- /* Disable MAC */
- sw_w32_mask(0, 1, RTL930X_MAC_FORCE_MODE_CTRL + 4 * port);
- mdelay(20);
-
- /* ----> dal_longan_sds_mode_set */
- pr_info("%s: Configuring RTL9300 SERDES %d\n", __func__, sds_num);
-
- /* Configure link to MAC */
- rtl9300_serdes_mac_link_config(sds_num, true, true); /* MAC Construct */
-
- /* Re-Enable MAC */
- sw_w32_mask(1, 0, RTL930X_MAC_FORCE_MODE_CTRL + 4 * port);
-
- /* Enable SDS in desired mode */
- rtsds_930x_mode_set(sds_num, phy_mode);
-
- /* Enable Fiber RX */
- rtl9300_sds_field_w(sds_num, 0x20, 2, 12, 12, 0);
-
- /* Calibrate SerDes receiver in loopback mode */
- rtl9300_sds_10g_idle(sds_num);
- do {
- rtl9300_do_rx_calibration(sds_num, phy_mode);
- calib_tries++;
- mdelay(50);
- } while (rtl9300_sds_check_calibration(sds_num, phy_mode) && calib_tries < 3);
- if (calib_tries >= 3)
- pr_warn("%s: SerDes RX calibration failed\n", __func__);
-
- /* Leave loopback mode */
- rtl9300_sds_tx_config(sds_num, phy_mode);
-
- return 0;
-}
-
-static int rtl9300_sds_10g_idle(int sds_num)
-{
- bool busy;
- int i = 0;
-
- do {
- if (sds_num % 2) {
- rtl9300_sds_field_w(sds_num - 1, 0x1f, 0x2, 15, 0, 53);
- busy = !!rtl9300_sds_field_r(sds_num - 1, 0x1f, 0x14, 1, 1);
- } else {
- rtl9300_sds_field_w(sds_num, 0x1f, 0x2, 15, 0, 53);
- busy = !!rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 0, 0);
- }
- i++;
- } while (busy && i < 100);
-
- if (i < 100)
- return 0;
-
- pr_warn("%s WARNING: Waiting for RX idle timed out, SDS %d\n", __func__, sds_num);
- return -EIO;
-}
-
-typedef struct {
- u8 page;
- u8 reg;
- u16 data;
-} sds_config;
-
-static const sds_config rtsds_930x_cfg_10gr_even[] =
-{
- /* 1G */
- {0x00, 0x0E, 0x3053}, {0x01, 0x14, 0x0100}, {0x21, 0x03, 0x8206},
- {0x21, 0x05, 0x40B0}, {0x21, 0x06, 0x0010}, {0x21, 0x07, 0xF09F},
- {0x21, 0x0C, 0x0007}, {0x21, 0x0D, 0x6009}, {0x21, 0x0E, 0x0000},
- {0x21, 0x0F, 0x0008}, {0x24, 0x00, 0x0668}, {0x24, 0x02, 0xD020},
- {0x24, 0x06, 0xC000}, {0x24, 0x0B, 0x1892}, {0x24, 0x0F, 0xFFDF},
- {0x24, 0x12, 0x03C4}, {0x24, 0x13, 0x027F}, {0x24, 0x14, 0x1311},
- {0x24, 0x16, 0x00C9}, {0x24, 0x17, 0xA100}, {0x24, 0x1A, 0x0001},
- {0x24, 0x1C, 0x0400}, {0x25, 0x01, 0x0300}, {0x25, 0x02, 0x1017},
- {0x25, 0x03, 0xFFDF}, {0x25, 0x05, 0x7F7C}, {0x25, 0x07, 0x8100},
- {0x25, 0x08, 0x0001}, {0x25, 0x09, 0xFFD4}, {0x25, 0x0A, 0x7C2F},
- {0x25, 0x0E, 0x003F}, {0x25, 0x0F, 0x0121}, {0x25, 0x10, 0x0020},
- {0x25, 0x11, 0x8840}, {0x2B, 0x13, 0x0050}, {0x2B, 0x18, 0x8E88},
- {0x2B, 0x19, 0x4902}, {0x2B, 0x1D, 0x2501}, {0x2D, 0x13, 0x0050},
- {0x2D, 0x18, 0x8E88}, {0x2D, 0x19, 0x4902}, {0x2D, 0x1D, 0x2641},
- {0x2F, 0x13, 0x0050}, {0x2F, 0x18, 0x8E88}, {0x2F, 0x19, 0x4902},
- {0x2F, 0x1D, 0x66E1},
- /* 3.125G */
- {0x28, 0x00, 0x0668}, {0x28, 0x02, 0xD020}, {0x28, 0x06, 0xC000},
- {0x28, 0x0B, 0x1892}, {0x28, 0x0F, 0xFFDF}, {0x28, 0x12, 0x01C4},
- {0x28, 0x13, 0x027F}, {0x28, 0x14, 0x1311}, {0x28, 0x16, 0x00C9},
- {0x28, 0x17, 0xA100}, {0x28, 0x1A, 0x0001}, {0x28, 0x1C, 0x0400},
- {0x29, 0x01, 0x0300}, {0x29, 0x02, 0x1017}, {0x29, 0x03, 0xFFDF},
- {0x29, 0x05, 0x7F7C}, {0x29, 0x07, 0x8100}, {0x29, 0x08, 0x0001},
- {0x29, 0x09, 0xFFD4}, {0x29, 0x0A, 0x7C2F}, {0x29, 0x0E, 0x003F},
- {0x29, 0x0F, 0x0121}, {0x29, 0x10, 0x0020}, {0x29, 0x11, 0x8840},
- /* 10G */
- {0x06, 0x0D, 0x0F00}, {0x06, 0x00, 0x0000}, {0x06, 0x01, 0xC800},
- {0x21, 0x03, 0x8206}, {0x21, 0x05, 0x40B0}, {0x21, 0x06, 0x0010},
- {0x21, 0x07, 0xF09F}, {0x21, 0x0C, 0x0007}, {0x21, 0x0D, 0x6009},
- {0x21, 0x0E, 0x0000}, {0x21, 0x0F, 0x0008}, {0x2E, 0x00, 0xA668},
- {0x2E, 0x02, 0xD020}, {0x2E, 0x06, 0xC000}, {0x2E, 0x0B, 0x1892},
- {0x2E, 0x0F, 0xFFDF}, {0x2E, 0x11, 0x8280}, {0x2E, 0x12, 0x0044},
- {0x2E, 0x13, 0x027F}, {0x2E, 0x14, 0x1311}, {0x2E, 0x17, 0xA100},
- {0x2E, 0x1A, 0x0001}, {0x2E, 0x1C, 0x0400}, {0x2F, 0x01, 0x0300},
- {0x2F, 0x02, 0x1217}, {0x2F, 0x03, 0xFFDF}, {0x2F, 0x05, 0x7F7C},
- {0x2F, 0x07, 0x80C4}, {0x2F, 0x08, 0x0001}, {0x2F, 0x09, 0xFFD4},
- {0x2F, 0x0A, 0x7C2F}, {0x2F, 0x0E, 0x003F}, {0x2F, 0x0F, 0x0121},
- {0x2F, 0x10, 0x0020}, {0x2F, 0x11, 0x8840}, {0x2F, 0x14, 0xE008},
- {0x2B, 0x13, 0x0050}, {0x2B, 0x18, 0x8E88}, {0x2B, 0x19, 0x4902},
- {0x2B, 0x1D, 0x2501}, {0x2D, 0x13, 0x0050}, {0x2D, 0x17, 0x4109},
- {0x2D, 0x18, 0x8E88}, {0x2D, 0x19, 0x4902}, {0x2D, 0x1C, 0x1109},
- {0x2D, 0x1D, 0x2641}, {0x2F, 0x13, 0x0050}, {0x2F, 0x18, 0x8E88},
- {0x2F, 0x19, 0x4902}, {0x2F, 0x1D, 0x76E1},
-};
-
-static const sds_config rtsds_930x_cfg_10gr_odd[] =
-{
- /* 1G */
- {0x00, 0x0E, 0x3053}, {0x01, 0x14, 0x0100}, {0x21, 0x03, 0x8206},
- {0x21, 0x06, 0x0010}, {0x21, 0x07, 0xF09F}, {0x21, 0x0A, 0x0003},
- {0x21, 0x0B, 0x0005}, {0x21, 0x0C, 0x0007}, {0x21, 0x0D, 0x6009},
- {0x21, 0x0E, 0x0000}, {0x21, 0x0F, 0x0008}, {0x24, 0x00, 0x0668},
- {0x24, 0x02, 0xD020}, {0x24, 0x06, 0xC000}, {0x24, 0x0B, 0x1892},
- {0x24, 0x0F, 0xFFDF}, {0x24, 0x12, 0x03C4}, {0x24, 0x13, 0x027F},
- {0x24, 0x14, 0x1311}, {0x24, 0x16, 0x00C9}, {0x24, 0x17, 0xA100},
- {0x24, 0x1A, 0x0001}, {0x24, 0x1C, 0x0400}, {0x25, 0x00, 0x820F},
- {0x25, 0x01, 0x0300}, {0x25, 0x02, 0x1017}, {0x25, 0x03, 0xFFDF},
- {0x25, 0x05, 0x7F7C}, {0x25, 0x07, 0x8100}, {0x25, 0x08, 0x0001},
- {0x25, 0x09, 0xFFD4}, {0x25, 0x0A, 0x7C2F}, {0x25, 0x0E, 0x003F},
- {0x25, 0x0F, 0x0121}, {0x25, 0x10, 0x0020}, {0x25, 0x11, 0x8840},
- {0x2B, 0x13, 0x3D87}, {0x2B, 0x14, 0x3108}, {0x2D, 0x13, 0x3C87},
- {0x2D, 0x14, 0x1808},
- /* 3.125G */
- {0x28, 0x00, 0x0668}, {0x28, 0x02, 0xD020}, {0x28, 0x06, 0xC000},
- {0x28, 0x0B, 0x1892}, {0x28, 0x0F, 0xFFDF}, {0x28, 0x12, 0x01C4},
- {0x28, 0x13, 0x027F}, {0x28, 0x14, 0x1311}, {0x28, 0x16, 0x00C9},
- {0x28, 0x17, 0xA100}, {0x28, 0x1A, 0x0001}, {0x28, 0x1C, 0x0400},
- {0x29, 0x00, 0x820F}, {0x29, 0x01, 0x0300}, {0x29, 0x02, 0x1017},
- {0x29, 0x03, 0xFFDF}, {0x29, 0x05, 0x7F7C}, {0x29, 0x07, 0x8100},
- {0x29, 0x08, 0x0001}, {0x29, 0x0A, 0x7C2F}, {0x29, 0x0E, 0x003F},
- {0x29, 0x0F, 0x0121}, {0x29, 0x10, 0x0020}, {0x29, 0x11, 0x8840},
- /* 10G */
- {0x06, 0x0D, 0x0F00}, {0x06, 0x00, 0x0000}, {0x06, 0x01, 0xC800},
- {0x21, 0x03, 0x8206}, {0x21, 0x05, 0x40B0}, {0x21, 0x06, 0x0010},
- {0x21, 0x07, 0xF09F}, {0x21, 0x0A, 0x0003}, {0x21, 0x0B, 0x0005},
- {0x21, 0x0C, 0x0007}, {0x21, 0x0D, 0x6009}, {0x21, 0x0E, 0x0000},
- {0x21, 0x0F, 0x0008}, {0x2E, 0x00, 0xA668}, {0x2E, 0x02, 0xD020},
- {0x2E, 0x06, 0xC000}, {0x2E, 0x0B, 0x1892}, {0x2E, 0x0F, 0xFFDF},
- {0x2E, 0x11, 0x8280}, {0x2E, 0x12, 0x0044}, {0x2E, 0x13, 0x027F},
- {0x2E, 0x14, 0x1311}, {0x2E, 0x17, 0xA100}, {0x2E, 0x1A, 0x0001},
- {0x2E, 0x1C, 0x0400}, {0x2F, 0x00, 0x820F}, {0x2F, 0x01, 0x0300},
- {0x2F, 0x02, 0x1217}, {0x2F, 0x03, 0xFFDF}, {0x2F, 0x05, 0x7F7C},
- {0x2F, 0x07, 0x80C4}, {0x2F, 0x08, 0x0001}, {0x2F, 0x09, 0xFFD4},
- {0x2F, 0x0A, 0x7C2F}, {0x2F, 0x0E, 0x003F}, {0x2F, 0x0F, 0x0121},
- {0x2F, 0x10, 0x0020}, {0x2F, 0x11, 0x8840}, {0x2B, 0x13, 0x3D87},
- {0x2B, 0x14, 0x3108}, {0x2D, 0x13, 0x3C87}, {0x2D, 0x14, 0x1808},
-};
-
-static const sds_config rtsds_930x_cfg_10g_2500bx_even[] =
-{
- {0x00, 0x0E, 0x3053}, {0x01, 0x14, 0x0100},
- {0x21, 0x03, 0x8206}, {0x21, 0x05, 0x40B0}, {0x21, 0x06, 0x0010}, {0x21, 0x07, 0xF09F},
- {0x21, 0x0C, 0x0007}, {0x21, 0x0D, 0x6009}, {0x21, 0x0E, 0x0000}, {0x21, 0x0F, 0x0008},
- {0x24, 0x00, 0x0668}, {0x24, 0x02, 0xD020}, {0x24, 0x06, 0xC000}, {0x24, 0x0B, 0x1892},
- {0x24, 0x0F, 0xFFDF}, {0x24, 0x12, 0x03C4}, {0x24, 0x13, 0x027F}, {0x24, 0x14, 0x1311},
- {0x24, 0x16, 0x00C9}, {0x24, 0x17, 0xA100}, {0x24, 0x1A, 0x0001}, {0x24, 0x1C, 0x0400},
- {0x25, 0x01, 0x0300}, {0x25, 0x02, 0x1017}, {0x25, 0x03, 0xFFDF}, {0x25, 0x05, 0x7F7C},
- {0x25, 0x07, 0x8100}, {0x25, 0x08, 0x0001}, {0x25, 0x09, 0xFFD4}, {0x25, 0x0A, 0x7C2F},
- {0x25, 0x0E, 0x003F}, {0x25, 0x0F, 0x0121}, {0x25, 0x10, 0x0020}, {0x25, 0x11, 0x8840},
- {0x28, 0x00, 0x0668}, {0x28, 0x02, 0xD020}, {0x28, 0x06, 0xC000}, {0x28, 0x0B, 0x1892},
- {0x28, 0x0F, 0xFFDF}, {0x28, 0x12, 0x01C4}, {0x28, 0x13, 0x027F}, {0x28, 0x14, 0x1311},
- {0x28, 0x16, 0x00C9}, {0x28, 0x17, 0xA100}, {0x28, 0x1A, 0x0001}, {0x28, 0x1C, 0x0400},
- {0x29, 0x01, 0x0300}, {0x29, 0x02, 0x1017}, {0x29, 0x03, 0xFFDF}, {0x29, 0x05, 0x7F7C},
- {0x29, 0x07, 0x8100}, {0x29, 0x08, 0x0001}, {0x29, 0x09, 0xFFD4}, {0x29, 0x0A, 0x7C2F},
- {0x29, 0x0E, 0x003F}, {0x29, 0x0F, 0x0121}, {0x29, 0x10, 0x0020}, {0x29, 0x11, 0x8840},
- {0x2B, 0x13, 0x0050}, {0x2B, 0x18, 0x8E88}, {0x2B, 0x19, 0x4902}, {0x2B, 0x1D, 0x2501},
- {0x2D, 0x13, 0x0050}, {0x2D, 0x18, 0x8E88}, {0x2D, 0x17, 0x4109}, {0x2D, 0x19, 0x4902},
- {0x2D, 0x1C, 0x1109}, {0x2D, 0x1D, 0x2641},
- {0x2F, 0x13, 0x0050}, {0x2F, 0x18, 0x8E88}, {0x2F, 0x19, 0x4902}, {0x2F, 0x1D, 0x66E1},
-};
-
-static const sds_config rtsds_930x_cfg_10g_2500bx_odd[] =
-{
- {0x00, 0x0E, 0x3053}, {0x01, 0x14, 0x0100},
- {0x21, 0x03, 0x8206}, {0x21, 0x06, 0x0010}, {0x21, 0x07, 0xF09F}, {0x21, 0x0A, 0x0003},
- {0x21, 0x0B, 0x0005}, {0x21, 0x0C, 0x0007}, {0x21, 0x0D, 0x6009}, {0x21, 0x0E, 0x0000},
- {0x21, 0x0F, 0x0008},
- {0x24, 0x00, 0x0668}, {0x24, 0x02, 0xD020}, {0x24, 0x06, 0xC000}, {0x24, 0x0B, 0x1892},
- {0x24, 0x0F, 0xFFDF}, {0x24, 0x12, 0x03C4}, {0x24, 0x13, 0x027F}, {0x24, 0x14, 0x1311},
- {0x24, 0x16, 0x00C9}, {0x24, 0x17, 0xA100}, {0x24, 0x1A, 0x0001}, {0x24, 0x1C, 0x0400},
- {0x25, 0x00, 0x820F}, {0x25, 0x01, 0x0300}, {0x25, 0x02, 0x1017}, {0x25, 0x03, 0xFFDF},
- {0x25, 0x05, 0x7F7C}, {0x25, 0x07, 0x8100}, {0x25, 0x08, 0x0001}, {0x25, 0x09, 0xFFD4},
- {0x25, 0x0A, 0x7C2F}, {0x25, 0x0E, 0x003F}, {0x25, 0x0F, 0x0121}, {0x25, 0x10, 0x0020},
- {0x25, 0x11, 0x8840},
- {0x28, 0x00, 0x0668}, {0x28, 0x02, 0xD020}, {0x28, 0x06, 0xC000}, {0x28, 0x0B, 0x1892},
- {0x28, 0x0F, 0xFFDF}, {0x28, 0x12, 0x01C4}, {0x28, 0x13, 0x027F}, {0x28, 0x14, 0x1311},
- {0x28, 0x16, 0x00C9}, {0x28, 0x17, 0xA100}, {0x28, 0x1A, 0x0001}, {0x28, 0x1C, 0x0400},
- {0x29, 0x00, 0x820F}, {0x29, 0x01, 0x0300}, {0x29, 0x02, 0x1017}, {0x29, 0x03, 0xFFDF},
- {0x29, 0x05, 0x7F7C}, {0x29, 0x07, 0x8100}, {0x29, 0x08, 0x0001}, {0x29, 0x0A, 0x7C2F},
- {0x29, 0x0E, 0x003F}, {0x29, 0x0F, 0x0121}, {0x29, 0x10, 0x0020}, {0x29, 0x11, 0x8840},
- {0x2B, 0x13, 0x3D87}, {0x2B, 0x14, 0x3108},
- {0x2D, 0x13, 0x3C87}, {0x2D, 0x14, 0x1808},
-};
-
-sds_config rtsds_930x_cfg_usxgmii_qx_even[] =
-{
- {0x06, 0x00, 0x0000}, {0x06, 0x0D, 0x0F00}, {0x06, 0x0E, 0x055A}, {0x06, 0x1D, 0x0600},
- {0x07, 0x10, 0x6003}, {0x06, 0x13, 0x68C1}, {0x06, 0x14, 0xF021}, {0x07, 0x06, 0x1401},
- {0x21, 0x03, 0x8206}, {0x21, 0x05, 0x40B0}, {0x21, 0x06, 0x0010}, {0x21, 0x07, 0xF09F},
- {0x21, 0x0C, 0x0007}, {0x21, 0x0D, 0x6009}, {0x21, 0x0E, 0x0000}, {0x21, 0x0F, 0x0008},
- {0x2E, 0x00, 0xA668}, {0x2E, 0x01, 0x2088}, {0x2E, 0x02, 0xD020}, {0x2E, 0x06, 0xC000},
- {0x2E, 0x0B, 0x1892}, {0x2E, 0x0F, 0xFFDF}, {0x2E, 0x11, 0x8280}, {0x2E, 0x12, 0x0484},
- {0x2E, 0x13, 0x027F}, {0x2E, 0x14, 0x1311}, {0x2E, 0x17, 0xA100}, {0x2E, 0x1A, 0x0001},
- {0x2E, 0x1C, 0x0400}, {0x2F, 0x01, 0x0300}, {0x2F, 0x02, 0x1017}, {0x2F, 0x03, 0xFFDF},
- {0x2F, 0x05, 0x7F7C}, {0x2F, 0x07, 0x8104}, {0x2F, 0x08, 0x0001}, {0x2F, 0x09, 0xFFD4},
- {0x2F, 0x0A, 0x7C2F}, {0x2F, 0x0E, 0x003F}, {0x2F, 0x0F, 0x0121}, {0x2F, 0x10, 0x0020},
- {0x2F, 0x11, 0x8840},
- {0x2B, 0x13, 0x0050}, {0x2B, 0x18, 0x8E88}, {0x2B, 0x19, 0x4902}, {0x2B, 0x1D, 0x2501},
- {0x2D, 0x13, 0x0050}, {0x2D, 0x18, 0x8E88}, {0x2D, 0x19, 0x4902}, {0x2D, 0x1D, 0x2641},
- {0x2F, 0x13, 0x0050}, {0x2F, 0x18, 0x8E88}, {0x2F, 0x19, 0x4902}, {0x2F, 0x1D, 0x66E1},
- /* enable IEEE 802.3az EEE */
- {0x06, 0x03, 0xc45c},
-};
-
-sds_config rtsds_930x_cfg_usxgmii_qx_odd[] =
-{
- {0x06, 0x00, 0x0000}, {0x06, 0x0D, 0x0F00}, {0x06, 0x0E, 0x055A}, {0x06, 0x1D, 0x0600},
- {0x07, 0x10, 0x6003}, {0x06, 0x13, 0x68C1}, {0x06, 0x14, 0xF021}, {0x07, 0x06, 0x1401},
- {0x21, 0x03, 0x8206}, {0x21, 0x05, 0x40B0}, {0x21, 0x06, 0x0010}, {0x21, 0x07, 0xF09F},
- {0x21, 0x0A, 0x0003}, {0x21, 0x0B, 0x0005}, {0x21, 0x0C, 0x0007}, {0x21, 0x0D, 0x6009},
- {0x21, 0x0E, 0x0000}, {0x21, 0x0F, 0x0008},
- {0x2E, 0x00, 0xA668}, {0x2E, 0x02, 0xD020}, {0x2E, 0x06, 0xC000}, {0x2E, 0x0B, 0x1892},
- {0x2E, 0x0F, 0xFFDF}, {0x2E, 0x11, 0x8280}, {0x2E, 0x12, 0x0484}, {0x2E, 0x13, 0x027F},
- {0x2E, 0x14, 0x1311}, {0x2E, 0x17, 0xA100}, {0x2E, 0x1A, 0x0001}, {0x2E, 0x1C, 0x0400},
- {0x2F, 0x00, 0x820F}, {0x2F, 0x01, 0x0300}, {0x2F, 0x02, 0x1017}, {0x2F, 0x03, 0xFFDF},
- {0x2F, 0x05, 0x7F7C}, {0x2F, 0x07, 0x8104}, {0x2F, 0x08, 0x0001}, {0x2F, 0x09, 0xFFD4},
- {0x2F, 0x0A, 0x7C2F}, {0x2F, 0x0E, 0x003F}, {0x2F, 0x0F, 0x0121}, {0x2F, 0x10, 0x0020},
- {0x2F, 0x11, 0x8840},
- {0x2B, 0x13, 0x3D87}, {0x2B, 0x14, 0x3108},
- {0x2D, 0x13, 0x3C87}, {0x2D, 0x14, 0x1808},
- /* enable IEEE 802.3az EEE */
- {0x06, 0x03, 0xc45c},
-};
-
-static void rtsds_930x_usxgmii_config(int sds, int nway_en, u32 opcode, u32 am_period, u32 all_am_markers, u32 an_table, u32 sync_bit)
-{
- rtl9300_sds_field_w(sds, 0x7, 0x11, 0, 0, nway_en);
- rtl9300_sds_field_w(sds, 0x7, 0x11, 1, 1, nway_en);
- rtl9300_sds_field_w(sds, 0x7, 0x11, 2, 2, nway_en);
- rtl9300_sds_field_w(sds, 0x7, 0x11, 3, 3, nway_en);
- rtl9300_sds_field_w(sds, 0x6, 0x12, 15, 0, am_period);
- rtl9300_sds_field_w(sds, 0x6, 0x13, 7, 0, all_am_markers);
- rtl9300_sds_field_w(sds, 0x6, 0x13, 15, 8, all_am_markers);
- rtl9300_sds_field_w(sds, 0x6, 0x14, 7, 0, all_am_markers);
- rtl9300_sds_field_w(sds, 0x6, 0x14, 15, 8, all_am_markers);
- rtl9300_sds_field_w(sds, 0x6, 0x15, 7, 0, all_am_markers);
- rtl9300_sds_field_w(sds, 0x6, 0x15, 15, 8, all_am_markers);
- rtl9300_sds_field_w(sds, 0x6, 0x16, 7, 0, all_am_markers);
- rtl9300_sds_field_w(sds, 0x6, 0x16, 15, 8, all_am_markers);
- rtl9300_sds_field_w(sds, 0x6, 0x17, 7, 0, all_am_markers);
- rtl9300_sds_field_w(sds, 0x6, 0x17, 15, 8, all_am_markers);
- rtl9300_sds_field_w(sds, 0x6, 0x18, 7, 0, all_am_markers);
- rtl9300_sds_field_w(sds, 0x6, 0x18, 15, 8, all_am_markers);
- rtl9300_sds_field_w(sds, 0x7, 0x10, 7, 0, opcode);
- rtl9300_sds_field_w(sds, 0x6, 0xe, 10, 10, an_table);
- rtl9300_sds_field_w(sds, 0x6, 0x1d, 11, 10, sync_bit);
-}
-
-static void rtsds_930x_patch_serdes(int sds, phy_interface_t mode)
-{
- const bool even_sds = ((sds & 1) == 0);
- const sds_config *config;
- size_t count;
-
- switch (mode) {
- case PHY_INTERFACE_MODE_1000BASEX:
- case PHY_INTERFACE_MODE_SGMII:
- case PHY_INTERFACE_MODE_10GBASER:
- if (even_sds) {
- config = rtsds_930x_cfg_10gr_even;
- count = ARRAY_SIZE(rtsds_930x_cfg_10gr_even);
- } else {
- config = rtsds_930x_cfg_10gr_odd;
- count = ARRAY_SIZE(rtsds_930x_cfg_10gr_odd);
- }
- break;
-
- case PHY_INTERFACE_MODE_2500BASEX:
- if (even_sds) {
- config = rtsds_930x_cfg_10g_2500bx_even;
- count = ARRAY_SIZE(rtsds_930x_cfg_10g_2500bx_even);
- } else {
- config = rtsds_930x_cfg_10g_2500bx_odd;
- count = ARRAY_SIZE(rtsds_930x_cfg_10g_2500bx_odd);
- }
- break;
-
- case PHY_INTERFACE_MODE_10G_QXGMII:
- if (even_sds) {
- config = rtsds_930x_cfg_usxgmii_qx_even;
- count = ARRAY_SIZE(rtsds_930x_cfg_usxgmii_qx_even);
- } else {
- config = rtsds_930x_cfg_usxgmii_qx_odd;
- count = ARRAY_SIZE(rtsds_930x_cfg_usxgmii_qx_odd);
- }
- break;
-
- default:
- pr_warn("%s: unsupported mode %s on serdes %d\n", __func__, phy_modes(mode), sds);
- return;
- }
-
- for (size_t i = 0; i < count; ++i) {
- rtmdio_930x_write_sds_phy(sds, config[i].page,
- config[i].reg,
- config[i].data);
- }
-
- if (mode == PHY_INTERFACE_MODE_10G_QXGMII) {
- /* Default configuration */
- rtsds_930x_usxgmii_config(sds, 1, 0xaa, 0x5078, 0, 1, 0x1);
- }
-}
-
-int rtl9300_sds_cmu_band_get(int sds)
-{
- u32 page;
- u32 en;
- u32 cmu_band;
-
-/* page = rtl9300_sds_cmu_page_get(sds); */
- page = 0x25; /* 10GR and 1000BX */
- sds = (sds % 2) ? (sds - 1) : (sds);
-
- rtl9300_sds_field_w(sds, page, 0x1c, 15, 15, 1);
- rtl9300_sds_field_w(sds + 1, page, 0x1c, 15, 15, 1);
-
- en = rtl9300_sds_field_r(sds, page, 27, 1, 1);
- if(!en) { /* Auto mode */
- rtmdio_930x_write_sds_phy(sds, 0x1f, 0x02, 31);
-
- cmu_band = rtl9300_sds_field_r(sds, 0x1f, 0x15, 5, 1);
- } else {
- cmu_band = rtl9300_sds_field_r(sds, page, 30, 4, 0);
- }
-
- return cmu_band;
-}
-
static int rtl8214fc_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
{
__ETHTOOL_DECLARE_LINK_MODE_MASK(support) = { 0, };
return rtl8390_configure_generic(phydev);
}
-static int rtl9300_serdes_probe(struct phy_device *phydev)
-{
- if (soc_info.family != RTL9300_FAMILY_ID)
- return -ENODEV;
-
- phydev_info(phydev, "Detected internal RTL9300 Serdes\n");
-
- return 0;
-}
-
static struct phy_driver rtl83xx_phy_driver[] = {
{
PHY_ID_MATCH_EXACT(PHY_ID_RTL8214C),
.suspend = genphy_suspend,
.resume = genphy_resume,
},
- {
- PHY_ID_MATCH_MODEL(PHY_ID_RTL9300_I),
- .name = "REALTEK RTL9300 SERDES",
- .features = PHY_GBIT_FIBRE_FEATURES,
- .read_page = rtl821x_read_page,
- .write_page = rtl821x_write_page,
- .probe = rtl9300_serdes_probe,
- .suspend = genphy_suspend,
- .resume = genphy_resume,
- .read_status = rtl9300_read_status,
- },
};
module_phy_driver(rtl83xx_phy_driver);
projects / thirdparty / openwrt.git / commitdiff
