realtek: rtl930x: add support for Sirivision SR-ST3408F

This commit adds support for the Sirivision SR-ST3408F,
an 8-port 10G switch with 4x RJ45 ports and 4x SFP ports.

SoC:      Realtek RTL9303
RAM:      512 MiB DDR3
Flash:    SPI-NOR 16 MiB (Winbond)
Ethernet: 4x RJ45 via RTL8261BE PHY (10G/5G/2.5G/1G/100M/10M)
          4x SFP+
LEDs:     1x power, 1x system green
          2x RJ45 LEDs/port (link/act, 10G)
          1x SFP+ LED/port (link/act)
Button:   Reset
Console:  Cisco-style RJ45, 115200 8n1
Fan:      4040 12V fan (hardwired)
Power:    12V 3A internal PSU

OpenWrt installation
---------------------

1. Attach to serial console using a Cisco cable, 115200 8n1
2. Power on the switch and rapidly press Esc to interrupt U-Boot
3. Initialize the RJ45 ports by running `rtk network on`
4. Serve the initramfs-kernel.bin image on TFTP, IP 192.168.1.111
5. Use any RJ45 port to connect to your TFTP server
6. Run `tftpboot 0x81000000 initramfs-kernel.bin; bootm`
7. Use `mtd dump` or `dd` to backup the original firmware at `mtd5` first
8. Run sysupgrade to flash sysupgrade.bin into the switch and reboot

Restoring original firmware
-----------------------------

Vendor does not provide firmware images, so you should have made a backup.
Use `mtd write` to restore your backed up copy into the `mtd5` partition.

MAC Address
------------
All interfaces are assigned the same MAC address, from the U-Boot env
`ethaddr`. This MAC address is also printed on the device label.

Signed-off-by: Darell Tan <darell.tan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23686
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>

diff --git a/target/linux/realtek/base-files/etc/board.d/02_network b/target/linux/realtek/base-files/etc/board.d/02_network
index 11c7673007973e7a478c1b607cb4038b15646077..a85fbfc173e4c96d57a320e1466fb296ff2f96be 100644 (file)
--- a/target/linux/realtek/base-files/etc/board.d/02_network
+++ b/target/linux/realtek/base-files/etc/board.d/02_network
@@ -93,6 +93,7 @@ realtek_setup_macs()
        plasmacloud,psx8|\
        plasmacloud,psx10|\
        plasmacloud,psx28|\
+       sirivision,sr-st3408f|\
        zyxel,gs1920-24hp-v2)
                lan_mac="$(get_mac_label)"
                ;;

diff --git a/target/linux/realtek/dts/rtl9303_sirivision_sr-st3408f.dts b/target/linux/realtek/dts/rtl9303_sirivision_sr-st3408f.dts
new file mode 100644 (file)
index 0000000..067dbd1
--- /dev/null
+++ b/target/linux/realtek/dts/rtl9303_sirivision_sr-st3408f.dts
@@ -0,0 +1,261 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/dts-v1/;
+
+#include "rtl930x.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+       compatible = "sirivision,sr-st3408f", "realtek,rtl9303-soc";
+       model = "Sirivision SR-ST3408F";
+
+       memory@0 {
+               device_type = "memory";
+               reg = <0x00000000 0x10000000>, /* first 256 MiB */
+                     <0x20000000 0x10000000>; /* remaining 256 MiB */
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       aliases {
+               led-boot = &led_sys;
+               led-failsafe = &led_sys;
+               led-running = &led_sys;
+               led-upgrade = &led_sys;
+
+               label-mac-device = &ethernet0;
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               button-reset {
+                       label = "reset";
+                       gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_sys: led-0 {
+                       gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+                       color = <LED_COLOR_ID_GREEN>;
+                       function = LED_FUNCTION_STATUS;
+               };
+       };
+
+       led_set {
+               compatible = "realtek,rtl9300-leds";
+               active-low;
+
+               led_set0 = <
+                       (RTL93XX_LED_SET_10G | RTL93XX_LED_SET_LINK)
+                       (RTL93XX_LED_SET_10G | RTL93XX_LED_SET_5G | RTL93XX_LED_SET_2P5G |
+                        RTL93XX_LED_SET_1G | RTL93XX_LED_SET_100M | RTL93XX_LED_SET_10M |
+                        RTL93XX_LED_SET_LINK | RTL93XX_LED_SET_ACT)
+               >;
+
+               led_set1 = <
+                       (RTL93XX_LED_SET_NONE)  /* odd outputs are not connected */
+                       (RTL93XX_LED_SET_10G | RTL93XX_LED_SET_5G | RTL93XX_LED_SET_2P5G |
+                        RTL93XX_LED_SET_1G | RTL93XX_LED_SET_100M | RTL93XX_LED_SET_10M |
+                        RTL93XX_LED_SET_LINK | RTL93XX_LED_SET_ACT)
+               >;
+       };
+
+       sfp0: sfp-p5 {
+               compatible = "sff,sfp";
+               i2c-bus = <&i2c4>;
+               tx-disable-gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+               mod-def0-gpio = <&gpio1 13 GPIO_ACTIVE_LOW>;
+               los-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+               maximum-power-milliwatt = <2000>;
+               #thermal-sensor-cells = <0>;
+       };
+
+       sfp1: sfp-p6 {
+               compatible = "sff,sfp";
+               i2c-bus = <&i2c5>;
+               tx-disable-gpio = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+               mod-def0-gpio = <&gpio1 22 GPIO_ACTIVE_LOW>;
+               los-gpio = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+               maximum-power-milliwatt = <2000>;
+               #thermal-sensor-cells = <0>;
+       };
+
+       sfp2: sfp-p7 {
+               compatible = "sff,sfp";
+               i2c-bus = <&i2c6>;
+               tx-disable-gpio = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+               mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
+               los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+               maximum-power-milliwatt = <2000>;
+               #thermal-sensor-cells = <0>;
+       };
+
+       sfp3: sfp-p8 {
+               compatible = "sff,sfp";
+               i2c-bus = <&i2c7>;
+               tx-disable-gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+               mod-def0-gpio = <&gpio1 28 GPIO_ACTIVE_LOW>;
+               los-gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+               maximum-power-milliwatt = <2000>;
+               #thermal-sensor-cells = <0>;
+       };
+};
+
+&i2c_mst1 {
+       status = "okay";
+
+       i2c4: i2c@4 { reg = <4>; };
+       i2c5: i2c@5 { reg = <5>; };
+       i2c6: i2c@6 { reg = <6>; };
+       i2c7: i2c@7 { reg = <7>; };
+};
+
+&mdio_aux {
+       status = "okay";
+
+       gpio1: gpio@0 {
+               compatible = "realtek,rtl8231";
+               reg = <0>;
+
+               gpio-controller;
+               #gpio-cells = <2>;
+               gpio-ranges = <&gpio1 0 0 37>;
+
+               led-controller {
+                       compatible = "realtek,rtl8231-leds";
+                       status = "disabled";
+               };
+       };
+};
+
+&spi0 {
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <10000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x0 0xe0000>;
+                               read-only;
+                       };
+
+                       partition@e0000 {
+                               label = "u-boot-env";
+                               reg = <0xe0000 0x10000>;
+
+                               nvmem-layout {
+                                       compatible = "u-boot,env";
+
+                                       macaddr_ubootenv_ethaddr: ethaddr {
+                                               #nvmem-cell-cells = <1>;
+                                       };
+                               };
+                       };
+
+                       partition@f0000 {
+                               label = "u-boot-env2";
+                               reg = <0xf0000 0x10000>;
+                               read-only;
+                       };
+
+                       partition@100000 {
+                               label = "jffs";
+                               reg = <0x100000 0x100000>;
+                       };
+
+                       partition@200000 {
+                               label = "jffs2";
+                               reg = <0x200000 0x100000>;
+                       };
+
+                       partition@300000 {
+                               label = "firmware";
+                               reg = <0x300000 0xd00000>;
+                               compatible = "openwrt,uimage", "denx,uimage";
+                               openwrt,ih-magic = <0x93000000>;
+                       };
+               };
+       };
+};
+
+/* serdes for 10G PHYs have TX polarity inverted */
+&serdes2 { tx-polarity = <PHY_POL_INVERT>; };
+&serdes3 { tx-polarity = <PHY_POL_INVERT>; };
+&serdes4 { tx-polarity = <PHY_POL_INVERT>; };
+&serdes5 { tx-polarity = <PHY_POL_INVERT>; };
+
+&mdio_bus0 {
+       PHY_C45(0, 0)
+       PHY_C45(8, 1)
+       PHY_C45(16, 2)
+       PHY_C45(20, 3)
+};
+
+&ethernet0 {
+       nvmem-cells = <&macaddr_ubootenv_ethaddr 0>;
+       nvmem-cell-names = "mac-address";
+};
+
+&switch0 {
+       ethernet-ports {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               /* RJ45 ports, lan1-4 */
+               SWITCH_PORT_LED(0,  1, 2, 0, 0, usxgmii)
+               SWITCH_PORT_LED(8,  2, 3, 0, 0, usxgmii)
+               SWITCH_PORT_LED(16, 3, 4, 0, 0, usxgmii)
+               SWITCH_PORT_LED(20, 4, 5, 0, 0, usxgmii)
+
+               /* SFP+ ports, lan5-8 */
+               SWITCH_PORT_SFP(24, 5, 6, 1, 0)
+               SWITCH_PORT_SFP(25, 6, 7, 1, 1)
+               SWITCH_PORT_SFP(26, 7, 8, 1, 2)
+               SWITCH_PORT_SFP(27, 8, 9, 1, 3)
+
+               /* CPU port */
+               port@28 {
+                       ethernet = <&ethernet0>;
+                       reg = <28>;
+                       phy-mode = "internal";
+
+                       fixed-link {
+                               speed = <1000>;
+                               full-duplex;
+                       };
+               };
+       };
+};
+
+&thermal_zones {
+       sfp-thermal {
+               polling-delay-passive = <10000>;
+               polling-delay = <10000>;
+               thermal-sensors = <&sfp0>, <&sfp1>, <&sfp2>, <&sfp3>;
+               trips {
+                       sfp-crit {
+                               temperature = <110000>;
+                               hysteresis = <1000>;
+                               type = "critical";
+                       };
+               };
+       };
+};

diff --git a/target/linux/realtek/image/rtl930x.mk b/target/linux/realtek/image/rtl930x.mk
index 2ae8677e40061332581c70413c04f66848bda7b4..9b01f629ac254faed47c892725d4cb02bfbe4276 100644 (file)
--- a/target/linux/realtek/image/rtl930x.mk
+++ b/target/linux/realtek/image/rtl930x.mk
@@ -12,6 +12,17 @@ define Device/d-link_dgs-1250-28x
 endef
 TARGET_DEVICES += d-link_dgs-1250-28x
 
+define Device/sirivision_sr-st3408f
+  SOC := rtl9303
+  UIMAGE_MAGIC := 0x93000000
+  DEVICE_VENDOR := Sirivision
+  DEVICE_MODEL := SR-ST3408F
+  DEVICE_PACKAGES := kmod-phy-realtek rtl8261n-firmware
+  IMAGE_SIZE := 13312k
+  $(Device/kernel-lzma)
+endef
+TARGET_DEVICES += sirivision_sr-st3408f
+
 define Device/hasivo_f1100w-4sx-4xgt-common
   SOC := rtl9303
   DEVICE_VENDOR := Hasivo