From: Markus Breitenberger <bre@keba.com>
Date: Mon, 13 Jul 2026 17:16:19 +0000 (+0200)
Subject: net: stmmac: intel: skip SerDes reconfig when rate is unchanged
X-Git-Url: http://git.ipfire.org/gitweb.cgi?a=commitdiff_plain;h=0ab78ead2481adb52f9eb5b403865c529f6f2348;p=thirdparty%2Fkernel%2Flinux.git

net: stmmac: intel: skip SerDes reconfig when rate is unchanged

intel_mac_finish() is registered as the phylink mac_finish()
callback for the Elkhart Lake SGMII ports. phylink calls it at
the end of every major link reconfiguration, including the
initial one during probe.

The callback selects the PMC ModPHY LCPLL programming for the
requested MAC-side interface and then power-cycles the SerDes.
On Elkhart Lake that ModPHY is also used by the on-die AHCI
SATA PHY. Reapplying the programming during the initial
boot-time link-up disturbs the shared analog block while it is
still driving SATA, so the SATA link fails to train:

  ata1: SATA link down (SStatus 1 SControl 300)

The disk carrying the root filesystem is never detected and the
system hangs at rootwait. Ethernet itself comes up normally,
which makes the failure look unrelated to the network driver.

Before mac_finish() runs, the legacy SerDes power-up path has
already programmed SERDES_GCR0 for the current interface. The
1G and 2.5G ModPHY tables selected by mac_finish() correspond
to the SerDes lane rate, so read that rate back from SERDES_GCR0
and skip the PMC reprogramming and SerDes power-cycle when it
already matches the selected interface.

This keeps the disruptive reprogramming out of the boot path
when the SerDes is configured correctly, while preserving the
previous behavior when a real SGMII/1000BASE-X to 2500BASE-X
rate change is needed. If the register read fails, reconfigure
as before.

Fixes: a42f6b3f1cc1 ("net: stmmac: configure SerDes according to the interface mode")
Cc: stable@vger.kernel.org
Signed-off-by: Markus Breitenberger <bre@keba.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260713171619.192452-1-bre@breiti.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
---

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
index b8d467ba6d72..4d207f41a43b 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
@@ -525,6 +525,32 @@ static int intel_set_reg_access(const struct pmc_serdes_regs *regs, int max_regs
 	return ret;
 }
 
+/*
+ * Return true if the SerDes lane rate must change to serve @interface.
+ * If the current rate cannot be determined, reconfigure as before.
+ */
+static bool intel_serdes_needs_reconfig(struct stmmac_priv *priv,
+					struct intel_priv_data *intel_priv,
+					phy_interface_t interface)
+{
+	u32 cur_rate, want_rate;
+	int data;
+
+	if (!intel_priv->mdio_adhoc_addr)
+		return true;
+
+	data = mdiobus_read(priv->mii, intel_priv->mdio_adhoc_addr,
+			    SERDES_GCR0);
+	if (data < 0)
+		return true;
+
+	cur_rate = (data & SERDES_RATE_MASK) >> SERDES_RATE_PCIE_SHIFT;
+	want_rate = interface == PHY_INTERFACE_MODE_2500BASEX ?
+			SERDES_RATE_PCIE_GEN2 : SERDES_RATE_PCIE_GEN1;
+
+	return cur_rate != want_rate;
+}
+
 static int intel_mac_finish(struct net_device *ndev,
 			    void *intel_data,
 			    unsigned int mode,
@@ -536,6 +562,11 @@ static int intel_mac_finish(struct net_device *ndev,
 	int max_regs = 0;
 	int ret = 0;
 
+	if (!intel_serdes_needs_reconfig(priv, intel_priv, interface)) {
+		priv->plat->phy_interface = interface;
+		return 0;
+	}
+
 	ret = intel_tsn_lane_is_available(ndev, intel_priv);
 	if (ret < 0) {
 		netdev_info(priv->dev, "No TSN lane available to set the registers.\n");