From: Gunther Stammwitz Date: Mon, 1 Jun 2026 16:00:29 +0000 (+0200) Subject: ramips: add support for Yuncore 1200F X-Git-Url: http://git.ipfire.org/gitweb.cgi?a=commitdiff_plain;h=1ba7b38cfc82d2624b1fab6e2b373aff04c1a57b;p=thirdparty%2Fopenwrt.git ramips: add support for Yuncore 1200F The Yuncore 1200F is an outdoor 802.11ac access point based on the MediaTek MT7628AN SoC with an MT7663E PCIe 5 GHz radio. The device is also sold under the KuWFi AP1200F name. Hardware: - SoC: MediaTek MT7628AN - CPU: MIPS 24KEc - RAM: 64 MiB - Flash: 8 MiB SPI NOR - Ethernet: 2x 10/100 Mbps - WiFi 2.4 GHz: MT7628AN WMAC - WiFi 5 GHz: MT7663E PCIe - LEDs: status, LAN, WAN - Button: reset - Watchdog: GPIO watchdog MAC addresses: - Ethernet: factory 0x0004 - 2.4 GHz WiFi: factory 0x0028 - 5 GHz WiFi: factory 0x8004 Network: - LAN: eth0.1, switch port 4 - WAN: eth0.2, switch port 3 Installation: - Build the sysupgrade image: openwrt-ramips-mt76x8-yuncore_1200f-squashfs-sysupgrade.bin - The stock firmware provides a U-Boot recovery web interface. It can be entered by holding the reset button while powering on the device. Connect to http://192.168.0.100/ and upload openwrt-sysupgrade.bin file. Recovery: - Reverting to stock firmware has not been tested. The 5 GHz radio is detected as PCI ID 14c3:7663 and uses mt7615e together with the MT7663 AP firmware. kmod-mt76x2 is explicitly excluded because this board uses MT7663E, not MT76x2. Tested: - Build succeeds for ramips/mt76x8 - Sysupgrade image boots - Ethernet LAN/WAN work - 2.4 GHz AP starts on phy0 - 5 GHz AP starts on phy1 - Stable MAC addresses are assigned to Ethernet, phy0 and phy1 Signed-off-by: Gunther Stammwitz Link: https://github.com/openwrt/openwrt/pull/23613 Signed-off-by: Jonas Jelonek --- diff --git a/target/linux/ramips/dts/mt7628an_yuncore_1200f.dts b/target/linux/ramips/dts/mt7628an_yuncore_1200f.dts new file mode 100644 index 00000000000..054a6774bee --- /dev/null +++ b/target/linux/ramips/dts/mt7628an_yuncore_1200f.dts @@ -0,0 +1,206 @@ +#include "mt7628an.dtsi" + +#include +#include +#include + +/ { + compatible = "yuncore,1200f", "mediatek,mt7628an-soc"; + model = "Yuncore 1200F"; + + chosen { + bootargs = "console=ttyS0,57600"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 38 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + aliases { + label-mac = ðernet; + led-boot = &led_indicator; + led-failsafe = &led_indicator; + led-running = &led_indicator; + led-upgrade = &led_indicator; + }; + + leds { + compatible = "gpio-leds"; + + led_indicator: indicator { + color = ; + function = LED_FUNCTION_INDICATOR; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + + lan { + color = ; + function = LED_FUNCTION_LAN; + gpios = <&gpio 39 GPIO_ACTIVE_LOW>; + }; + + wan { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&gpio 40 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <0>; + gpios = <&gpio 44 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0radio"; + }; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio 37 GPIO_ACTIVE_HIGH>; + hw_algo = "toggle"; + hw_margin_ms = <20000>; + always-running; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x400>; + }; + + /* + * Observed at factory + 0x4: + * 9c:e5:49:60:2a:64 + */ + macaddr_factory_4: macaddr@4 { + reg = <0x4 0x6>; + }; + + /* + * Observed at factory + 0x28: + * 9c:e5:49:60:2a:65 + */ + macaddr_factory_28: macaddr@28 { + reg = <0x28 0x6>; + }; + + eeprom_factory_8000: eeprom@8000 { + reg = <0x8000 0x4da8>; + }; + + /* + * Observed at factory + 0x8004: + * 9c:e5:49:60:2a:66 + * + * Do not apply mac-address-increment here. + * The stored address is already the final 5 GHz MAC. + */ + macaddr_factory_8004: macaddr@8004 { + reg = <0x8004 0x6>; + }; + }; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x50000 0x7b0000>; + }; + }; + }; +}; + +ðernet { + nvmem-cells = <&macaddr_factory_4>; + nvmem-cell-names = "mac-address"; +}; + +&esw { + mediatek,portmap = <0x2f>; +}; + +&wmac { + status = "okay"; + + nvmem-cells = <&eeprom_factory_0>, <&macaddr_factory_28>; + nvmem-cell-names = "eeprom", "mac-address"; + + /* + * Allow full 2.4 GHz band. The previous upper limit of 2462000 + * caused channels 10-13 to appear disabled. + */ + ieee80211-freq-limit = <2400000 2500000>; +}; + +&state_default { + gpio { + groups = "pwm1", "pwm0", "uart2", "uart1", "i2c", "refclk", + "sdmode", "i2s", "spi cs1", "spis", + "gpio", "p0led_an", "p1led_an", "p2led_an", "p3led_an", + "p4led_an", "wled_kn", "wled_an", "p0led_kn", "p1led_kn", + "p2led_kn", "p3led_kn", "p4led_kn"; + function = "gpio"; + }; + +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + + nvmem-cells = <&eeprom_factory_8000>, <&macaddr_factory_8004>; + nvmem-cell-names = "eeprom", "mac-address"; + + ieee80211-freq-limit = <5000000 6000000>; + + led { + led-sources = <2>; + led-active-low; + }; + }; +}; diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk index ea9676a1762..6f7f382203f 100644 --- a/target/linux/ramips/image/mt76x8.mk +++ b/target/linux/ramips/image/mt76x8.mk @@ -1543,3 +1543,14 @@ define Device/teltonika_rut241 IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | append-metadata endef TARGET_DEVICES += teltonika_rut241 + +define Device/yuncore_1200f + IMAGE_SIZE := 7872k + DEVICE_VENDOR := Yuncore + DEVICE_MODEL := 1200F + DEVICE_ALT0_VENDOR := KuWFi + DEVICE_ALT0_MODEL := AP1200F + SUPPORTED_DEVICES += yuncore,1200f + DEVICE_PACKAGES := kmod-mt7615e kmod-mt7663-firmware-ap -kmod-mt76x2 -kmod-mt76x2-common -kmod-mt76x02-common +endef +TARGET_DEVICES += yuncore_1200f diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds index 89365fe4b45..5b85303cde2 100644 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds @@ -24,6 +24,10 @@ yuncore,m300) ucidef_set_led_switch "lan" "lan" "green:lan" "switch0" "0xf" ucidef_set_led_switch "wan" "wan" "green:wan" "switch0" "0x10" ;; +yuncore,1200f) + ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x10" + ucidef_set_led_switch "wan" "WAN" "green:wan" "switch0" "0x08" + ;; creality,wb-01) ucidef_set_led_switch "lan" "lan" "blue:lan" "switch0" "0x1" ;; diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network index c410554aea1..ae05ffccc9b 100644 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network @@ -258,6 +258,10 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "0:lan:2" "2:lan:1" "4:wan" "6@eth0" ;; + yuncore,1200f) + ucidef_add_switch "switch0" \ + "4:lan" "3:wan" "6@eth0" + ;; yuncore,cpe200) ucidef_add_switch "switch0" \ "0:lan" "4:wan" "6@eth0"