Some HP machines with Realtek codecs have mute LEDs connected to VREF pins.
However when these go into runtime suspend, the pin powers down and its
pin control is disabled, thus disabling the LED too.
This patch fixes that issue by making sure that the pin stays in D0 with
correct pin control.
BugLink: https://bugs.launchpad.net/bugs/1248465 Tested-by: Franz Hsieh <franz.hsieh@canonical.com> Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Haswell HDMI audio controllers seem to get stuck when unaligned buffer
size is used. Let's enable the buffer alignment for the corresponding
entries.
Since AZX_DCAPS_INTEL_PCH contains AZX_DCAPS_BUFSIZE that disables the
buffer alignment forcibly, define AZX_DCAPS_INTEL_HASWELL and put the
necessary AZX_DCAPS bits there.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60769 Reported-by: Alexander E. Patrakov <patrakov@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a bitmask to hda_gen_spec indicating NIDs to exclude from the
possible volume controls. That is, when the bit is set, the NID
corresponding to the bit won't be picked as an output volume control
any longer.
Basically this is just a band-aid for working around the issue found
with CS4208 codec, where only the headphone pin has a volume AMP with
different dB steps.
msnd_pinnacle.c is used for both snd-msnd-pinnacle and
snd-msnd-classic drivers, and both should have different driver
names. Using the same driver name results in the sysfs warning for
duplicated entries like
kobject: 'msnd-pinnacle.7' (cec33408): kobject_release, parent (null) (delayed)
kobject: 'msnd-pinnacle' (cecd4980): kobject_release, parent cf3ad9b0 (delayed)
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:486 sysfs_warn_dup+0x7d/0xa0()
sysfs: cannot create duplicate filename '/bus/isa/drivers/msnd-pinnacle'
......
The commit [8fe7b65ab465: ALSA: hda - Apply GPIO setup for MacBooks
with CS4208] added a fixup entry matching with the vendor id 0x106b.
This broke the fixups for previous MBA6,1 and 6,2, since the PCI SSID
vendor id matches before evaluating the codec SSIDs.
We had a similar issue on Mac with Sigmatel codecs, and solve this
problem again similarly, by introducing a skeleton entry matching with
the all MacBooks, then remap to the right one.
The drain and drain_notify callback were blocked by low level driver
until the draining was complete. Due to this being invoked with big
fat mutex held, others ops like reading timestamp, calling pause, drop
were blocked.
So to fix this we add a new snd_compr_drain_notify() API. This would
be required to be invoked by low level driver when drain or partial
drain has been completed by the DSP. Thus we make the drain and
partial_drain callback as non blocking and driver returns immediately
after notifying DSP. The waiting is done while releasing the lock so
that other ops can go ahead.
[ The commit 917f4b5cba78 was wrongly applied from the preliminary
patch. This commit corrects to the final version.
Sorry for inconvenience! -- tiwai ]
The drain and drain_notify callback were blocked by low level driver untill the
draining was complete. Due to this being invoked with big fat mutex held, others
ops like reading timestamp, calling pause, drop were blocked.
So to fix this we add a new snd_compr_drain_notify() API. This would be required
to be invoked by low level driver when drain or partial drain has been completed
by the DSP. Thus we make the drain and partial_drain callback as non blocking
and driver returns immediately after notifying DSP.
The waiting is done while relasing the lock so that other ops can go ahead.
The probe code of snd-usb-6fire driver overrides the devices[] pointer
wrongly without checking whether it's already occupied or not. This
would screw up the device disconnection later.
The get_dumpable() return value is not boolean. Most users of the
function actually want to be testing for non-SUID_DUMP_USER(1) rather than
SUID_DUMP_DISABLE(0). The SUID_DUMP_ROOT(2) is also considered a
protected state. Almost all places did this correctly, excepting the two
places fixed in this patch.
Wrong logic:
if (dumpable == SUID_DUMP_DISABLE) { /* be protective */ }
or
if (dumpable == 0) { /* be protective */ }
or
if (!dumpable) { /* be protective */ }
Correct logic:
if (dumpable != SUID_DUMP_USER) { /* be protective */ }
or
if (dumpable != 1) { /* be protective */ }
Without this patch, if the system had set the sysctl fs/suid_dumpable=2, a
user was able to ptrace attach to processes that had dropped privileges to
that user. (This may have been partially mitigated if Yama was enabled.)
The macros have been moved into the file that declares get/set_dumpable(),
which means things like the ia64 code can see them too.
Many btusb devices have 2 modes, a hid mode and a bluetooth hci mode. These
devices default to hid mode for BIOS use. This means that after having been
reset they will revert to HID mode, and are no longer usable as a HCI.
Therefor it is a very bad idea to just blindly make reset_resume point to
the regular resume handler. Note that the btusb driver has no clue how to
switch these devices from hid to hci mode, this is done in userspace through
udev rules, so the proper way to deal with this is to not have a reset-resume
handler and instead let the usb-system re-enumerate the device, and re-run
the udev rules.
I must also note, that the commit message for the commit causing this
problem has a very weak motivation for the change:
"Add missing reset_resume dev_pm_ops. Missing reset_resume results in the
following message after power management device test. This change sets
reset_resume to btusb_resume().
[ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?"
Making a change solely to silence a warning while also changing important
behavior (normal resume handling versus re-enumeration) requires a commit
message with a proper explanation why it is safe to do so, which clearly lacks
here, and unsurprisingly it turns out to not be safe to make this change.
Reverting the commit in question fixes bt no longer working on my Dell
E6430 after a suspend/resume, and I believe it likely also fixes the
following bugs:
https://bugzilla.redhat.com/show_bug.cgi?id=988481
https://bugzilla.redhat.com/show_bug.cgi?id=1010649
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1213239
In commit 3d81535ea5940446510a8a5cee1c6ad23c90c753
(rt2800: 5592: add chip specific vgc calculations)
the rt2800_link_tuner function has been modified to
adjust VGC level for the RT5592 chipset.
On the RT5592 chipset, the VGC level must be adjusted
only if rssi is greater than -65. However the current
code adjusts the VGC value by 0x10 regardless of the
actual chipset if the rssi value is between -80 and
-65.
Fix the broken behaviour by reordering the if-else
statements.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "rt2x00: fix HT TX descriptor settings regression"
assumes that the control parameter to rt2x00mac_tx is always non-NULL.
There is an internal call in rt2x00lib_bc_buffer_iter where NULL is
passed. Fix the resulting crash by adding an initialized dummy on-stack
ieee80211_tx_control struct.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tests were added to lkdtm that grew the stack frame, the stack
corruption test stopped working. This isolates the test in its own
function, and forces it not to be inlined.
`comedi_alloc_spriv()` allocates private storage for a comedi subdevice
and sets the `SRF_FREE_SPRIV` flag in the `runflags` member of the
subdevice to allow the private storage to be automatically freed when
the comedi device is being cleaned up. Unfortunately, the flag gets
clobbered by `do_cmd_ioctl()` which calls
`comedi_set_subdevice_runflags()` with a mask value `~0` and only the
`SRF_USER` and `SRF_RUNNING` flags set, all the other SRF flags being
cleared.
Change the calls to `comedi_set_subdevice_runflags()` that currently use
a mask value of `~0` to use a more relevant mask value. For
`do_cmd_ioctl()`, the relevant SRF flags are `SRF_USER`, `SRF_ERROR` and
`SRF_RUNNING`. (At one time, `SRF_RT` would be included in that set of
flags, but it is no longer used.) For `comedi_alloc_spriv()` replace
the call to `comedi_set_subdevice_runflags()` with a simple
OR-assignment to avoid unnecessary use of a spin-lock.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the bug in reset_store caused by accessing NULL pointer.
The bdev gets its value from bdget_disk() which could fail when memory
pressure is severe and hence can return NULL because allocation of
inode in bdget could fail.
Hence, this patch introduces a check for bdev to prevent reference to a
NULL pointer in the later part of the code. It also removes unnecessary
check of bdev for fsync_bdev().
According to the ACPI spec (5.0, Section 6.3.5), the "Device
insertion in progress (pending)" (0x80) _OST status code is
reserved for the "Insertion Processing" (0x200) source event
which is "a result of an OSPM action". Specifically, it is not
a notification, so that status code should not be used during
notification processing, which unfortunately is done by
acpi_scan_bus_device_check().
For this reason, drop the ACPI_OST_SC_INSERT_IN_PROGRESS _OST
status evaluation from there (it was a mistake to put it in there
in the first place).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is required to do get_device() on the struct acpi_device in
question before passing it to acpi_bus_hot_remove_device() through
acpi_os_hotplug_execute(), because acpi_bus_hot_remove_device()
calls acpi_scan_hot_remove() that does put_device() on that
object.
The ACPI PCI root removal routine, handle_root_bridge_removal(),
doesn't do that, which may lead to premature freeing of the
device object or to executing put_device() on an object that
has been freed already.
Fix this problem by making handle_root_bridge_removal() use
get_device() as appropriate.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Toshi Kani <toshi.kani@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some firmware doesn't initialize initial backlight level to a proper
value and _BQC will return 0 on first time evaluation. We used to be
able to detect such incorrect value with our code logic, as value 0
normally isn't a valid value in _BCL. But with the introduction of Win8,
firmware begins to fill _BCL with values from 0 to 100, now 0 becomes
a valid value but that value will make user's screen black. This patch
test initial _BQC for value 0, if such a value is returned, do not use
it.
References: https://bugzilla.kernel.org/show_bug.cgi?id=64031
References: https://bugzilla.kernel.org/show_bug.cgi?id=61231
References: https://bugzilla.kernel.org/show_bug.cgi?id=63111 Reported-by: Qingshuai Tian <qingshuai.tian@intel.com> Tested-by: Aaron Lu <aaron.lu@intel.com> # on "Idealpad u330p" Reported-and-tested-by: <erno@iki.fi> # on "Acer Aspire V5-573G" Reported-and-tested-by: Kirill Tkhai <tkhai@yandex.ru> # on "HP 250 G1" Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bug was introduced by commit b76b51ba0cef ('ACPI / EC: Add more debug
info and trivial code cleanup') that erroneously caused the struct member
to be accessed before acquiring the required lock. This change fixes
it by ensuring the lock acquisition is done first.
Found by Aaron Durbin <adurbin@chromium.org>
Fixes: b76b51ba0cef ('ACPI / EC: Add more debug info and trivial code cleanup')
References: http://crbug.com/319019 Signed-off-by: Puneet Kumar <puneetster@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
[olof: Commit message reworded a bit] Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current default perf paranoid level is "1" which has
"perf_paranoid_kernel()" return false, and giving any operations that
use it, access to normal users. Unfortunately, this includes function
tracing and normal users should not be allowed to enable function
tracing by default.
The proper level is defined at "-1" (full perf access), which
"perf_paranoid_tracepoint_raw()" will only give access to. Use that
check instead for enabling function tracing.
Reported-by: Dave Jones <davej@redhat.com> Reported-by: Vince Weaver <vincent.weaver@maine.edu> Tested-by: Vince Weaver <vincent.weaver@maine.edu> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com>
CVE: CVE-2013-2930 Fixes: ced39002f5ea ("ftrace, perf: Add support to use function tracepoint in perf") Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike reported that commit 7d1a9417 ("x86: Use generic idle loop")
regressed several workloads and caused excessive reschedule
interrupts.
The patch in question failed to notice that the x86 code had an
inverted sense of the polling state versus the new generic code (x86:
default polling, generic: default !polling).
Fix the two prominent x86 mwait based idle drivers and introduce a few
new generic polling helpers (fixing the wrong smp_mb__after_clear_bit
usage).
Also switch the idle routines to using tif_need_resched() which is an
immediate TIF_NEED_RESCHED test as opposed to need_resched which will
end up being slightly different.
The hwmod init sequence involves initializing and idling all the
hwmods during bootup. If a module class has sysconfig, the init
sequence utilizes the module register base for performing any
sysc configuration.
The module address space is being removed from hwmod database and
retrieved from the <reg> property of the corresponding DT node.
If a hwmod does not have its corresponding DT node defined and the
memory address space is not defined in the corresponding
omap_hwmod_ocp_if, then the module register target address space
would be NULL and any sysc programming would result in a NULL
pointer dereference and a kernel boot hang.
Handle this scenario by checking for a valid module address space
during the _init of each hwmod, and leaving it in the registered
state if no module register address base is defined in either of
the hwmod data or the DT data.
Signed-off-by: Suman Anna <s-anna@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: Nishanth Menon <nm@ti.com> Acked-by: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: use -ENXIO rather than -ENOMEM to indicate a missing address
space error; fixed checkpatch.pl problem] Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 7dc19d5aff (convert shrinkers to new count/scan API)
the return value to PURGE_ALL_CACHES was dropped, causing -EPERM
to always be returned.
This patch re-adds the ret assignment, setting it to the the
ashmem_shrink_count(), which is the lru_count.
(Sorry this was missed in the review!)
Fixes: 7dc19d5affd7 ("convert shrinkers to new count/scan API") Cc: Colin Cross <ccross@android.com> Cc: Android Kernel Team <kernel-team@android.com> Cc: Glauber Costa <glommer@openvz.org> Reported-by: YongQin Liu <yongqin.liu@linaro.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Acked-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The oops is caused because shm_destroy() calls fput() after dropping the
ipc_lock. fput() clears the file's f_inode, f_path.dentry, and
f_path.mnt, which causes various NULL pointer references in task 2. I
reliably see the oops in task 2 if with shmlock, shmu
This patch fixes the races by:
1) set shm_file=NULL in shm_destroy() while holding ipc_object_lock().
2) modify at risk operations to check shm_file while holding
ipc_object_lock().
Example workloads, which each trigger oops...
Workload 1:
while true; do
id=$(shmget 1 4096)
shm_rmid $id &
shmlock $id &
wait
done
The oops stack shows accessing NULL f_inode due to racing fput:
_raw_spin_lock
shmem_lock
SyS_shmctl
Workload 2:
while true; do
id=$(shmget 1 4096)
shmat $id 4096 &
shm_rmid $id &
wait
done
The oops stack is similar to workload 1 due to NULL f_inode:
touch_atime
shmem_mmap
shm_mmap
mmap_region
do_mmap_pgoff
do_shmat
SyS_shmat
Workload 3:
while true; do
id=$(shmget 1 4096)
shmlock $id
shm_rmid $id &
shmunlock $id &
wait
done
The oops stack shows second fput tripping on an NULL f_inode. The
first fput() completed via from shm_destroy(), but a racing thread did
a get_file() and queued this fput():
locks_remove_flock
__fput
____fput
task_work_run
do_notify_resume
int_signal
Fixes: c2c737a0461e ("ipc,shm: shorten critical region for shmat") Fixes: 2caacaa82a51 ("ipc,shm: shorten critical region for shmctl") Signed-off-by: Greg Thelen <gthelen@google.com> Cc: Davidlohr Bueso <davidlohr@hp.com> Cc: Rik van Riel <riel@redhat.com> Cc: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2caacaa82a51 ("ipc,shm: shorten critical region for shmctl")
restructured the ipc shm to shorten critical region, but introduced a
path where the return value could be -EPERM, even if the operation
actually was performed.
Before the commit, the err return value was reset by the return value
from security_shm_shmctl() after the if (!ns_capable(...)) statement.
Now, we still exit the if statement with err set to -EPERM, and in the
case of SHM_UNLOCK, it is not reset at all, and used as the return value
from shmctl.
To fix this, we only set err when errors occur, leaving the fallthrough
case alone.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Davidlohr Bueso <davidlohr@hp.com> Cc: Rik van Riel <riel@redhat.com> Cc: Michel Lespinasse <walken@google.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes bug 62491 (https://bugzilla.kernel.org/show_bug.cgi?id=62491).
After resuming some users got the following error flooding the kernel log:
alx 0000:02:00.0: invalid PHY speed/duplex: 0xffff
Signed-off-by: Jonas Hahnfeld <linux@hahnjo.de> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: hahnjo <linux@hahnjo.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cbc-aes-s390 algorithm incorrectly places the IV in the tfm
data structure. As the tfm is shared between multiple threads,
this introduces a possibility of data corruption.
This patch fixes this by moving the parameter block containing
the IV and key onto the stack (the block is 48 bytes long).
The same bug exists elsewhere in the s390 crypto system and they
will be fixed in subsequent patches.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephan Mueller reported to me recently a error in random number generation in
the ansi cprng. If several small requests are made that are less than the
instances block size, the remainder for loop code doesn't increment
rand_data_valid in the last iteration, meaning that the last bytes in the
rand_data buffer gets reused on the subsequent smaller-than-a-block request for
random data.
The fix is pretty easy, just re-code the for loop to make sure that
rand_data_valid gets incremented appropriately
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Stephan Mueller <stephan.mueller@atsec.com> CC: Stephan Mueller <stephan.mueller@atsec.com> CC: Petr Matousek <pmatouse@redhat.com> CC: Herbert Xu <herbert@gondor.apana.org.au> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Cc: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A user reported a problem where they were getting csum errors when running a
balance and running systemd's journal. This is because systemd is awesome and
fallocate()'s its log space and writes into it. Unfortunately we assume that
when we read in all the csums for an extent that they are sequential starting at
the bytenr we care about. This obviously isn't the case for prealloc extents,
where we could have written to the middle of the prealloc extent only, which
means the csum would be for the bytenr in the middle of our range and not the
front of our range. Fix this by offsetting the new bytenr we are logging to
based on the original bytenr the csum was for. With this patch I no longer see
the csum errors I was seeing. Thanks,
Reported-by: Chris Murphy <lists@colorremedies.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices, like the Kvaser Memorator Professional, have several bulk in
endpoints. Only the first one found must be used by the driver. The same holds
for the bulk out endpoint. The official Kvaser driver (leaf) was used as
reference for this patch.
Today, if xfs_sb_read_verify encounters a v4 superblock
with junk past v4 fields which includes data in sb_crc,
it will be treated as a failing checksum and a significant
corruption.
There are known prior bugs which leave junk at the end
of the V4 superblock; we don't need to actually fail the
verification in this case if other checks pan out ok.
So if this is a secondary superblock, and the primary
superblock doesn't indicate that this is a V5 filesystem,
don't treat this as an actual checksum failure.
We should probably check the garbage condition as
we do in xfs_repair, and possibly warn about it
or self-heal, but that's a different scope of work.
Stable folks: This can go back to v3.10, which is what
introduced the sb CRC checking that is tripped up by old,
stale, incorrect V4 superblocks w/ unzeroed bits.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Acked-by: Dave Chinner <david@fromorbit.com> Reviewed-by: Mark Tinguely <tinguely@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that driver runs into a problem here if fibsize is too small
because we allocate user_srbcmd with fibsize size only but later we
access it until user_srbcmd->sg.count to copy it over to srbcmd.
It is not correct to test (fibsize < sizeof(*user_srbcmd)) because this
structure already includes one sg element and this is not needed for
commands without data. So, we would recommend to add the following
(instead of test for fibsize == 0).
Two drivers (atmel-pwm-bl and leds-atmel-pwm) currently depend on the
atmel_pwm driver to have bound to any pwm-device before their devices
are probed.
Support deferred probing of such devices by making sure to return
-EPROBE_DEFER from pwm_channel_alloc when no pwm-device has yet been
bound.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shadow bytes around the buggy address: ffff8800359c9700: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd ffff8800359c9780: fd fd fd fd fd fd fd fd fa fa fa fa fa fa fa fa ffff8800359c9800: fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa ffff8800359c9880: fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa ffff8800359c9900: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
=>ffff8800359c9980: 00 00 00 00 00 00 00 00 00 00 00 00 00 00[03]fb ffff8800359c9a00: fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa ffff8800359c9a80: fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa ffff8800359c9b00: fa fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00 ffff8800359c9b80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8800359c9c00: 00 00 00 00 00 00 00 00 fa fa fa fa fa fa fa fa
Shadow byte legend (one shadow byte represents 8 application bytes):
Addressable: 00
Partially addressable: 01 02 03 04 05 06 07
Heap redzone: fa
Heap kmalloc redzone: fb
Freed heap region: fd
Shadow gap: fe
The out-of-bounds access happens on 'parser->buffer[parser->idx] = 0;'
Although the crash happened in ftrace_regex_open() the real bug
occurred in trace_get_user() where there's an incrementation to
parser->idx without a check against the size. The way it is triggered
is if userspace sends in 128 characters (EVENT_BUF_SIZE + 1), the loop
that reads the last character stores it and then breaks out because
there is no more characters. Then the last character is read to determine
what to do next, and the index is incremented without checking size.
Then the caller of trace_get_user() usually nulls out the last character
with a zero, but since the index is equal to the size, it writes a nul
character after the allocated space, which can corrupt memory.
Luckily, only root user has write access to this file.
hdmi_setup_fake_chmap() is supposed to set the reported channel map when
the channel map is not specified by the user.
However, the function indexes channel_allocations[] with a wrong value
and extracts the wrong nibble from hdmi_channel_mapping[], causing wrong
channel maps to be shown.
Fix those issues.
Tested on Intel HDMI to correctly generate various channel maps, for
example 3,4,14,15,7,8,5,6 (instead of incorrect 3,4,8,7,5,6,14,0) for
standard 7.1 channel audio. (Note that the side and rear channels are
reported as RL/RR and RLC/RRC, respectively, as per the CEA-861
standard, instead of the more traditional SL/SR and RL/RR.)
Note that this only fixes the layouts that only contain traditional 7.1
speakers (2.0, 2.1, 4.0, 5.1, 7.1, etc.). E.g. the rear center of 6.1
is still being shown wrongly due to an issue with from_cea_slot()
which will be fixed in a later patch.
This patch adds a pci stub driver to hyper-fb. The hyperv framebuffer
driver will bind to the pci device then, so linux kernel and userspace
know there is a proper kernel driver for the device active. lspci shows
this for example:
[root@dhcp231 ~]# lspci -vs8
00:08.0 VGA compatible controller: Microsoft Corporation Hyper-V virtual
VGA (prog-if 00 [VGA controller])
Flags: bus master, fast devsel, latency 0, IRQ 11
Memory at f8000000 (32-bit, non-prefetchable) [size=64M]
Expansion ROM at <unassigned> [disabled]
Kernel driver in use: hyperv_fb
Another effect is that the xorg vesa driver will not attach to the
device and thus the Xorg server will automatically use the fbdev
driver instead.
On receiving a packet too big icmp error we update the expire value by
calling rt6_update_expires. This function uses dst_set_expires which is
implemented that it can only reduce the expiration value of the dst entry.
If we insert new routing non-expiry information into the ipv6 fib where
we already have a matching rt6_info we only clear the RTF_EXPIRES flag
in rt6i_flags and leave the dst.expires value as is.
When new mtu information arrives for that cached dst_entry we again
call dst_set_expires. This time it won't update the dst.expire value
because we left the dst.expire value intact from the last update. So
dst_set_expires won't touch dst.expires.
Fix this by resetting dst.expires when clearing the RTF_EXPIRE flag.
dst_set_expires checks for a zero expiration and updates the
dst.expires.
In the past this (not updating dst.expires) was necessary because
dst.expire was placed in a union with the dst_entry *from reference
and rt6_clean_expires did assign NULL to it. This split happend in ecd9883724b78cc72ed92c98bcb1a46c764fff21 ("ipv6: fix race condition
regarding dst->expires and dst->from").
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com> Reported-by: Valentijn Sessink <valentyn@blub.net> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Acked-by: Eric Dumazet <edumazet@google.com> Tested-by: Valentijn Sessink <valentyn@blub.net> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On receiving a packet too big icmp error we check if our current cached
dst_entry in the socket is still valid. This validation check did not
care about the expiration of the (cached) route.
The error path I traced down:
The socket receives a packet too big mtu notification. It still has a
valid dst_entry and thus issues the ip6_rt_pmtu_update on this dst_entry,
setting RTF_EXPIRE and updates the dst.expiration value (which could
fail because of not up-to-date expiration values, see previous patch).
In some seldom cases we race with a) the ip6_fib gc or b) another routing
lookup which would result in a recreation of the cached rt6_info from its
parent non-cached rt6_info. While copying the rt6_info we reinitialize the
metrics store by copying it over from the parent thus invalidating the
just installed pmtu update (both dsts use the same key to the inetpeer
storage). The dst_entry with the just invalidated metrics data would
just get its RTF_EXPIRES flag cleared and would continue to stay valid
for the socket.
We should have not issued the pmtu update on the already expired dst_entry
in the first placed. By checking the expiration on the dst entry and
doing a relookup in case it is out of date we close the race because
we would install a new rt6_info into the fib before we issue the pmtu
update, thus closing this race.
Not reliably updating the dst.expire value was fixed by the patch "ipv6:
reset dst.expires value when clearing expire flag".
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com> Reported-by: Valentijn Sessink <valentyn@blub.net> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Tested-by: Valentijn Sessink <valentyn@blub.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch ed08495c3 "tcp: use RTT from SACK for RTO" always re-arms RTO upon
obtaining a RTT sample from newly sacked data.
But technically RTO should only be re-armed when the data sent before
the last (re)transmission of write queue head are (s)acked. Otherwise
the RTO may continue to extend during loss recovery on data sent
in the future.
Note that RTTs from ACK or timestamps do not have this problem, as the RTT
source must be from data sent before.
The new RTO re-arm policy is
1) Always re-arm RTO if SND.UNA is advanced
2) Re-arm RTO if sack RTT is available, provided the sacked data was
sent before the last time write_queue_head was sent.
Signed-off-by: Larry Brakmo <brakmo@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch ed08495c3 "tcp: use RTT from SACK for RTO" has a bug that
it does not check if the ACK acknowledge new data before taking
the RTT sample from TCP timestamps. This patch adds the check
back as required by the RFC.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tp->lsndtime may not always be the SYNACK timestamp if a passive
Fast Open socket sends data before handshake completes. And if the
remote acknowledges both the data and the SYNACK, the RTT sample
is already taken in tcp_ack(), so no need to call
tcp_update_ack_rtt() in tcp_synack_rtt_meas() aagain.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ff50cd55545 ("tcp: gso: do not generate out of order packets")
had an heuristic that can trigger a warning in skb_try_coalesce(),
because skb->truesize of the gso segments were exactly set to mss.
ifconfig lo mtu 1500
ethtool -K lo tso off
netperf
As the skbs are looped into the TCP networking stack, skb_try_coalesce()
warns us of these skb under-estimating their truesize.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The length calculation here is now invalid on 32-bit architectures,
since sk_buff::tail is a pointer and sk_buff::transport_header is
an integer offset:
drivers/net/ethernet/chelsio/cxgb3/sge.c: In function 'write_ofld_wr':
drivers/net/ethernet/chelsio/cxgb3/sge.c:1603:9: warning: passing argument 4 of 'make_sgl' makes integer from pointer without a cast [enabled by default]
adap->pdev);
^
drivers/net/ethernet/chelsio/cxgb3/sge.c:964:28: note: expected 'unsigned int' but argument is of type 'sk_buff_data_t'
static inline unsigned int make_sgl(const struct sk_buff *skb,
^
Use the appropriate skb accessor functions.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: 1a37e412a022 ('net: Use 16bits for *_headers fields of struct skbuff') Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
time_after_eq() only works if the delta is < MAX_ULONG/2.
For a 32bit Dom0, if netfront sends packets at a very low rate, the time
between subsequent calls to tx_credit_exceeded() may exceed MAX_ULONG/2
and the test for timer_after_eq() will be incorrect. Credit will not be
replenished and the guest may become unable to send packets (e.g., if
prior to the long gap, all credit was exhausted).
Use jiffies_64 variant to mitigate this problem for 32bit Dom0.
Suggested-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Wei Liu <wei.liu2@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: Jason Luan <jianhai.luan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ab098df35f8b98b6553edc2e40234af512ba877 (virtio-net: don't respond to
cpu hotplug notifier if we're not ready) tries to bypass the cpu hotplug
notifier by checking the config_enable and does nothing is it was false. So it
need to try to hold the config_lock mutex which may happen in atomic
environment which leads the following warnings:
A correct fix is to unregister the hotcpu notifier during restore and register a
new one in resume.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Tested-by: Fengguang Wu <fengguang.wu@intel.com> Cc: Wanlong Gao <gaowanlong@cn.fujitsu.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't validate iph->ihl which may lead a dead loop if we meet a IPIP
skb whose iph->ihl is zero. Fix this by failing immediately when iph->ihl
is evil (less than 5).
Signed-off-by: Jason Wang <jasowang@redhat.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Petr Matousek <pmatouse@redhat.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Daniel Borkmann <dborkman@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduced in f9e42b853523 ("net: sctp: sideeffect: throw BUG if
primary_path is NULL"), we intended to find a buggy assoc that's
part of the assoc hash table with a primary_path that is NULL.
However, we better remove the BUG_ON for now and find a more
suitable place to assert for these things as Mark reports that
this also triggers the bug when duplication cookie processing
happens, and the assoc is not part of the hash table (so all
good in this case). Such a situation can for example easily be
reproduced by:
tc qdisc add dev eth0 root handle 1: prio bands 2 priomap 1 1 1 1 1 1
tc qdisc add dev eth0 parent 1:2 handle 20: netem loss 20%
tc filter add dev eth0 protocol ip parent 1: prio 2 u32 match ip \
protocol 132 0xff match u8 0x0b 0xff at 32 flowid 1:2
This drops 20% of COOKIE-ACK packets. After some follow-up
discussion with Vlad we came to the conclusion that for now we
should still better remove this BUG_ON() assertion, and come up
with two follow-ups later on, that is, i) find a more suitable
place for this assertion, and possibly ii) have a special
allocator/initializer for such kind of temporary assocs.
Reported-by: Mark Thomas <Mark.Thomas@metaswitch.com> Signed-off-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function mlx4_master_deactivate_admin_state() __mlx4_unregister_mac was
called using the MAC index. It should be called with the value of the MAC itself.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 3 Nov 2013 19:36:41 +0000 (11:36 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Three fixes across arch/mips with the most complex one being the GIC
interrupt fix - at nine lines still not monster. I'm confident this
are the final MIPS patches even if there should go for an rc8"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ralink: fix return value check in rt_timer_probe()
MIPS: malta: Fix GIC interrupt offsets
MIPS: Perf: Fix 74K cache map
Mathias Krause [Sun, 3 Nov 2013 11:36:28 +0000 (12:36 +0100)]
ipc, msg: forbid negative values for "msg{max,mnb,mni}"
Negative message lengths make no sense -- so don't do negative queue
lenghts or identifier counts. Prevent them from getting negative.
Also change the underlying data types to be unsigned to avoid hairy
surprises with sign extensions in cases where those variables get
evaluated in unsigned expressions with bigger data types, e.g size_t.
In case a user still wants to have "unlimited" sizes she could just use
INT_MAX instead.
Vineet Gupta [Sat, 2 Nov 2013 12:17:49 +0000 (17:47 +0530)]
ARC: Incorrect mm reference used in vmalloc fault handler
A vmalloc fault needs to sync up PGD/PTE entry from init_mm to current
task's "active_mm". ARC vmalloc fault handler however was using mm.
A vmalloc fault for non user task context (actually pre-userland, from
init thread's open for /dev/console) caused the handler to deref NULL mm
(for mm->pgd)
The reasons it worked so far is amazing:
1. By default (!SMP), vmalloc fault handler uses a cached value of PGD.
In SMP that MMU register is repurposed hence need for mm pointer deref.
2. In pre-3.12 SMP kernel, the problem triggering vmalloc didn't exist in
pre-userland code path - it was introduced with commit 20bafb3d23d108bc
"n_tty: Move buffers into n_tty_data"
Ming Lei [Fri, 1 Nov 2013 22:41:33 +0000 (09:11 +1030)]
scripts/kallsyms: filter symbols not in kernel address space
This patch uses CONFIG_PAGE_OFFSET to filter symbols which
are not in kernel address space because these symbols are
generally for generating code purpose and can't be run at
kernel mode, so we needn't keep them in /proc/kallsyms.
For example, on ARM there are some symbols which may be
linked in relocatable code section, then perf can't parse
symbols any more from /proc/kallsyms, this patch fixes the
problem (introduced b9b32bf70f2fb710b07c94e13afbc729afe221da)
Cc: Russell King <linux@arm.linux.org.uk> Cc: linux-arm-kernel@lists.infradead.org Cc: Michal Marek <mmarek@suse.cz> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: stable@vger.kernel.org
Linus Torvalds [Fri, 1 Nov 2013 19:23:56 +0000 (12:23 -0700)]
Merge tag 'usb-3.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a set of patches that revert all of the changes done to the
pl2303 USB serial driver in the 3.12-rc timeframe, as it turns out
they break some devices that work just fine on 3.11. As it's not a
good idea to break working systems, drop them all and they will be
reworked for future kernel versions such that there is no breakage.
I've also included a MAINTAINERS update for the USB serial subsystem
and a new device id for the ftdi_sio driver as well"
* tag 'usb-3.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: ftdi_sio: add id for Z3X Box device
USB: Maintainers change for usb serial drivers
Revert "USB: pl2303: restrict the divisor based baud rate encoding method to the "HX" chip type"
Revert "usb: pl2303: fix+improve the divsor based baud rate encoding method"
Revert "usb: pl2303: do not round to the next nearest standard baud rate for the divisor based baud rate encoding method"
Revert "usb: pl2303: remove 500000 baud from the list of standard baud rates"
Revert "usb: pl2303: move the two baud rate encoding methods to separate functions"
Revert "usb: pl2303: increase the allowed baud rate range for the divisor based encoding method"
Revert "usb: pl2303: also use the divisor based baud rate encoding method for baud rates < 115200 with HX chips"
Revert "usb: pl2303: add two comments concerning the supported baud rates with HX chips"
Revert "pl2303: simplify the else-if contruct for type_1 chips in pl2303_startup()"
Revert "pl2303: improve the chip type information output on startup"
Revert "pl2303: improve the chip type detection/distinction"
Revert "USB: pl2303: distinguish between original and cloned HX chips"
Linus Torvalds [Fri, 1 Nov 2013 19:23:22 +0000 (12:23 -0700)]
Merge tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound fixes from Takashi Iwai:
"The fixes for random bugs that have been reported lately in the game:
a few fixes in ASoC dpam and wm_hubs bugs spotted by Coverity, a
one-liner HD-audio fixup, and a fix for Oops with DPCM.
They are not so critically urgent bugs, but all small and safe"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: fix oops in snd_pcm_info() caused by ASoC DPCM
ASoC: wm_hubs: Add missing break in hp_supply_event()
ALSA: hda - Add a fixup for ASUS N76VZ
ASoC: dapm: Return -ENOMEM in snd_soc_dapm_new_dai_widgets()
ASoC: dapm: Fix source list debugfs outputs
Linus Torvalds [Fri, 1 Nov 2013 19:22:47 +0000 (12:22 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clock subsystem fixes from Mike Turquette.
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: fixup argument order when setting VCO parameters
clk: socfpga: Fix incorrect sdmmc clock name
clk: armada-370: fix tclk frequencies
clk: nomadik: set all timers to use 2.4 MHz TIMCLK
Greg Thelen [Fri, 1 Nov 2013 19:16:59 +0000 (12:16 -0700)]
memcg: remove incorrect underflow check
When a memcg is deleted mem_cgroup_reparent_charges() moves charged
memory to the parent memcg. As of v3.11-9444-g3ea67d0 "memcg: add per
cgroup writeback pages accounting" there's bad pointer read. The goal
was to check for counter underflow. The counter is a per cpu counter
and there are two problems with the code:
(1) per cpu access function isn't used, instead a naked pointer is used
which easily causes oops.
(2) the check doesn't sum all cpus
The fix is to remove the check. It's currently dangerous and isn't
worth fixing it to use something expensive, such as
percpu_counter_sum(), for each reparented page. __this_cpu_read() isn't
enough to fix this because there's no guarantees of the current cpus
count. The only guarantees is that the sum of all per-cpu counter is >=
nr_pages.
Greg KH [Wed, 30 Oct 2013 18:07:31 +0000 (11:07 -0700)]
USB: Maintainers change for usb serial drivers
Johan has been conned^Wgracious in accepting the maintainership of the
USB serial drivers, especially as he's been doing all of the real work
for the past few years.
At the same time, remove a bunch of old entries for USB serial drivers
that don't make sense anymore, given that the developers are no longer
around, and individual driver maintainerships for tiny things like this
is pretty pointless.
Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 31 Oct 2013 23:58:23 +0000 (16:58 -0700)]
Merge branch 'akpm' (fixes from Andrew Morton)
Merge four more fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
lib/scatterlist.c: don't flush_kernel_dcache_page on slab page
mm: memcg: fix test for child groups
mm: memcg: lockdep annotation for memcg OOM lock
mm: memcg: use proper memcg in limit bypass
Ming Lei [Thu, 31 Oct 2013 23:34:17 +0000 (16:34 -0700)]
lib/scatterlist.c: don't flush_kernel_dcache_page on slab page
Commit b1adaf65ba03 ("[SCSI] block: add sg buffer copy helper
functions") introduces two sg buffer copy helpers, and calls
flush_kernel_dcache_page() on pages in SG list after these pages are
written to.
Unfortunately, the commit may introduce a potential bug:
- Before sending some SCSI commands, kmalloc() buffer may be passed to
block layper, so flush_kernel_dcache_page() can see a slab page
finally
- According to cachetlb.txt, flush_kernel_dcache_page() is only called
on "a user page", which surely can't be a slab page.
- ARCH's implementation of flush_kernel_dcache_page() may use page
mapping information to do optimization so page_mapping() will see the
slab page, then VM_BUG_ON() is triggered.
Aaro Koskinen reported the bug on ARM/kirkwood when DEBUG_VM is enabled,
and this patch fixes the bug by adding test of '!PageSlab(miter->page)'
before calling flush_kernel_dcache_page().
Signed-off-by: Ming Lei <ming.lei@canonical.com> Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Tested-by: Simon Baatz <gmbnomis@gmail.com> Cc: Russell King - ARM Linux <linux@arm.linux.org.uk> Cc: Will Deacon <will.deacon@arm.com> Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Tejun Heo <tj@kernel.org> Cc: "James E.J. Bottomley" <JBottomley@parallels.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: <stable@vger.kernel.org> [3.2+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Thu, 31 Oct 2013 23:34:15 +0000 (16:34 -0700)]
mm: memcg: fix test for child groups
When memcg code needs to know whether any given memcg has children, it
uses the cgroup child iteration primitives and returns true/false
depending on whether the iteration loop is executed at least once or
not.
Because a cgroup's list of children is RCU protected, these primitives
require the RCU read-lock to be held, which is not the case for all
memcg callers. This results in the following splat when e.g. enabling
hierarchy mode:
In the memcg case, we only care about children when we are attempting to
modify inheritable attributes interactively. Racing with deletion could
mean a spurious -EBUSY, no problem. Racing with addition is handled
just fine as well through the memcg_create_mutex: if the child group is
not on the list after the mutex is acquired, it won't be initialized
from the parent's attributes until after the unlock.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Thu, 31 Oct 2013 23:34:13 +0000 (16:34 -0700)]
mm: memcg: use proper memcg in limit bypass
Commit 84235de394d9 ("fs: buffer: move allocation failure loop into the
allocator") allowed __GFP_NOFAIL allocations to bypass the limit if they
fail to reclaim enough memory for the charge. But because the main test
case was on a 3.2-based system, the patch missed the fact that on newer
kernels the charge function needs to return root_mem_cgroup when
bypassing the limit, and not NULL. This will corrupt whatever memory is
at NULL + percpu pointer offset. Fix this quickly before problems are
reported.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / thirdparty / kernel / stable.git / log
