page_pool_put_full_page() should only be invoked when freeing Rx buffers
or building a skb if the size is too short. At other times, the pages
need to be reused. So remove the redundant page put. In the original
code, double free pages cause kernel panic:
Errata i2312 [0] for K3 silicon mentions the maximum obtainable
timeout through MMC host controller is 700ms. And for commands taking
longer than 700ms, hardware timeout should be disabled and software
timeout should be used.
The workaround for Errata i2312 can be achieved by adding
SDHCI_QUIRK2_DISABLE_HW_TIMEOUT quirk in sdhci_am654.
Disable command queuing on Intel GLK-based Positivo models.
Without this quirk, CQE (Command Queuing Engine) causes instability
or I/O errors during operation. Disabling it ensures stable
operation on affected devices.
A new warning in clang [1] points out that id_reg is uninitialized then
passed to memstick_init_req() as a const pointer:
drivers/memstick/core/memstick.c:330:59: error: variable 'id_reg' is uninitialized when passed as a const pointer argument here [-Werror,-Wuninitialized-const-pointer]
330 | memstick_init_req(&card->current_mrq, MS_TPC_READ_REG, &id_reg,
| ^~~~~~
Commit de182cc8e882 ("drivers/memstick/core/memstick.c: avoid -Wnonnull
warning") intentionally passed this variable uninitialized to avoid an
-Wnonnull warning from a NULL value that was previously there because
id_reg is never read from the call to memstick_init_req() in
h_memstick_read_dev_id(). Just zero initialize id_reg to avoid the
warning, which is likely happening in the majority of builds using
modern compilers that support '-ftrivial-auto-var-init=zero'.
The nbpf->chan[] array is allocated earlier in the nbpf_probe() function
and it has "num_channels" elements. These three loops iterate one
element farther than they should and corrupt memory.
The changes to the second loop are more involved. In this case, we're
copying data from the irqbuf[] array into the nbpf->chan[] array. If
the data in irqbuf[i] is the error IRQ then we skip it, so the iterators
are not in sync. I added a check to ensure that we don't go beyond the
end of the irqbuf[] array. I'm pretty sure this can't happen, but it
seemed harmless to add a check.
On the other hand, after the loop has ended there is a check to ensure
that the "chan" iterator is where we expect it to be. In the original
code we went one element beyond the end of the array so the iterator
wasn't in the correct place and it would always return -EINVAL. However,
now it will always be in the correct place. I deleted the check since
we know the result.
Cc: stable@vger.kernel.org Fixes: b45b262cefd5 ("dmaengine: add a driver for AMBA AXI NBPF DMAC IP cores") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/b13c5225-7eff-448c-badc-a2c98e9bcaca@sabinyo.mountain Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently cpu hotplug with the PREEMPT_RT option set in the kernel is
not supported because the underlying generic power domain functions
used in the cpu hotplug callbacks are incompatible from a lock point
of view. This situation prevents the suspend to idle to reach the
deepest idle state for the "cluster" as identified in the
undermentioned commit.
Use the compatible ones when PREEMPT_RT is enabled and remove the
boolean disabling the hotplug callbacks with this option.
With this change the platform can reach the deepest idle state
allowing at suspend time to consume less power.
Due to what seem to be a bug with variant version returned by some
firmwares the code may set hdev->classify_pkt_type with
btintel_classify_pkt_type when in fact the controller doesn't even
support ISO channels feature but may use the handle range expected from
a controllers that does causing the packets to be reclassified as ISO
causing several bugs.
To fix the above btintel_classify_pkt_type will attempt to check if the
controller really supports ISO channels and in case it doesn't don't
reclassify even if the handle range is considered to be ISO, this is
considered safer than trying to fix the specific controller/firmware
version as that could change over time and causing similar problems in
the future.
When MSG_DONTWAIT is not set, the tpacket_snd operation will wait for
pending_refcnt to decrement to zero before returning. The pending_refcnt
is decremented by 1 when the skb->destructor function is called,
indicating that the skb has been successfully sent and needs to be
destroyed.
If an error occurs during this process, the tpacket_snd() function will
exit and return error, but pending_refcnt may not yet have decremented to
zero. Assuming the next send operation is executed immediately, but there
are no available frames to be sent in tx_ring (i.e., packet_current_frame
returns NULL), and skb is also NULL, the function will not execute
wait_for_completion_interruptible_timeout() to yield the CPU. Instead, it
will enter a do-while loop, waiting for pending_refcnt to be zero. Even
if the previous skb has completed transmission, the skb->destructor
function can only be invoked in the ksoftirqd thread (assuming NAPI
threading is enabled). When both the ksoftirqd thread and the tpacket_snd
operation happen to run on the same CPU, and the CPU trapped in the
do-while loop without yielding, the ksoftirqd thread will not get
scheduled to run. As a result, pending_refcnt will never be reduced to
zero, and the do-while loop cannot exit, eventually leading to a CPU soft
lockup issue.
In fact, skb is true for all but the first iterations of that loop, and
as long as pending_refcnt is not zero, even if incremented by a previous
call, wait_for_completion_interruptible_timeout() should be executed to
yield the CPU, allowing the ksoftirqd thread to be scheduled. Therefore,
the execution condition of this function should be modified to check if
pending_refcnt is not zero, instead of check skb.
- if (need_wait && skb) {
+ if (need_wait && packet_read_pending(&po->tx_ring)) {
As a result, the judgment conditions are duplicated with the end code of
the while loop, and packet_read_pending() is a very expensive function.
Actually, this loop can only exit when ph is NULL, so the loop condition
can be changed to while (1), and in the "ph = NULL" branch, if the
subsequent condition of if is not met, the loop can break directly. Now,
the loop logic remains the same as origin but is clearer and more obvious.
Fixes: 89ed5b519004 ("af_packet: Block execution of tasks waiting for transmit to complete in AF_PACKET") Cc: stable@kernel.org Suggested-by: LongJun Tang <tanglongjun@kylinos.cn> Signed-off-by: Yun Lu <luyun@kylinos.cn> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the changes in commit 581073f626e3 ("af_packet: do not call
packet_read_pending() from tpacket_destruct_skb()"), every time
tpacket_destruct_skb() is executed, the skb_completion is marked as
completed. When wait_for_completion_interruptible_timeout() returns
completed, the pending_refcnt has not yet been reduced to zero.
Therefore, when ph is NULL, the wait function may need to be called
multiple times until packet_read_pending() finally returns zero.
We should call sock_sndtimeo() only once, otherwise the SO_SNDTIMEO
constraint could be way off.
Fixes: 581073f626e3 ("af_packet: do not call packet_read_pending() from tpacket_destruct_skb()") Cc: stable@kernel.org Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Yun Lu <luyun@kylinos.cn> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware CS has a very slow rise time of about 6us,
causing transmission errors when CS does not reach
high between transaction.
It looks like it's not driven actively when transitioning
from low to high but switched to input, so only the CPU
pull-up pulls it high, slowly. Transitions from high to low
are fast. On the oscilloscope, CS looks like an irregular sawtooth
pattern like this:
_____
^ / |
^ /| / |
/| / | / |
/ | / | / |
___/ |___/ |_____/ |___
With cs-gpios we have a CS rise time of about 20ns, as it should be,
and CS looks rectangular.
This fixes the data errors when running a flashcp loop against a
m25p40 spi flash.
With the Rockchip 6.1 kernel we see the same slow rise time, but
for some reason CS is always high for long enough to reach a solid
high.
The RK3399 and RK3588 SoCs use the same SPI driver, so we also
checked our "Puma" (RK3399) and "Tiger" (RK3588) boards.
They do not have this problem. Hardware CS rise time is good.
The IMX8MPDS Table 37 [1] shows that the max SPI master read frequency
depends on the pins the interface is muxed behind with ECSPI2
muxed behind ECSPI2 supporting up to 25MHz.
Adjust the spi-max-frequency based on these findings.
The IMX8MPDS Table 37 [1] shows that the max SPI master read frequency
depends on the pins the interface is muxed behind with ECSPI2
muxed behind ECSPI2 supporting up to 25MHz.
Adjust the spi-max-frequency based on these findings.
The IMX8MPDS Table 37 [1] shows that the max SPI master read frequency
depends on the pins the interface is muxed behind with ECSPI2
muxed behind ECSPI2 supporting up to 25MHz.
Adjust the spi-max-frequency based on these findings.
LDO5 regulator is used to power the i.MX8MM NVCC_SD2 I/O supply, that is
used for the SD2 card interface and also for some GPIOs.
When the SD card interface is not enabled the regulator subsystem could
turn off this supply, since it is not used anywhere else, however this
will also remove the power to some other GPIOs, for example one I/O that
is used to power the ethernet phy, leading to a non working ethernet
interface.
[ 31.820515] On-module +V3.3_1.8_SD (LDO5): disabling
[ 31.821761] PMIC_USDHC_VSELECT: disabling
[ 32.764949] fec 30be0000.ethernet end0: Link is Down
Fix this keeping the LDO5 supply always on.
Cc: stable@vger.kernel.org Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini") Fixes: f5aab0438ef1 ("regulator: pca9450: Fix enable register for LDO5") Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Watchdog doesn't work on NXP ls1046ardb board because in commit 7c8ffc5555cb("arm64: dts: layerscape: remove big-endian for mmc nodes"),
it intended to remove the big-endian from mmc node, but the big-endian of
watchdog node is also removed by accident. So, add watchdog big-endian
property back.
In addition, add compatible string fsl,ls1046a-wdt, which allow big-endian
property.
Fixes: 7c8ffc5555cb ("arm64: dts: layerscape: remove big-endian for mmc nodes") Cc: stable@vger.kernel.org Signed-off-by: Meng Li <Meng.Li@windriver.com> Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IMX8MPDS Table 37 [1] shows that the max SPI master read frequency
depends on the pins the interface is muxed behind with ECSPI2
muxed behind ECSPI2 supporting up to 25MHz.
Adjust the spi-max-frequency based on these findings.
A new warning in clang [1] points out a place in pep_sock_accept() where
dst is uninitialized then passed as a const pointer to pep_find_pipe():
net/phonet/pep.c:829:37: error: variable 'dst' is uninitialized when passed as a const pointer argument here [-Werror,-Wuninitialized-const-pointer]
829 | newsk = pep_find_pipe(&pn->hlist, &dst, pipe_handle);
| ^~~:
Move the call to pn_skb_get_dst_sockaddr(), which initializes dst, to
before the call to pep_find_pipe(), so that dst is consistently used
initialized throughout the function.
mptcp_disconnect() clears the fallback bit unconditionally, without
touching the associated flags.
The bit clear is safe, as no fallback operation can race with that --
all subflow are already in TCP_CLOSE status thanks to the previous
FASTCLOSE -- but we need to consistently reset all the fallback related
status.
Also acquire the relevant lock, to avoid fouling static analyzers.
We have races similar to the one addressed by the previous patch between
subflow failing and additional subflow creation. They are just harder to
trigger.
The solution is similar. Use a separate flag to track the condition
'socket state prevent any additional subflow creation' protected by the
fallback lock.
The socket fallback makes such flag true, and also receiving or sending
an MP_FAIL option.
The field 'allow_infinite_fallback' is now always touched under the
relevant lock, we can drop the ONCE annotation on write.
Fixes: 478d770008b0 ("mptcp: send out MP_FAIL when data checksum fails") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20250714-net-mptcp-fallback-races-v1-2-391aff963322@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we need to track the 'fallback is possible' condition and the
fallback status separately, there are a few possible races open between
the check and the actual fallback action.
Add a spinlock to protect the fallback related information and use it
close all the possible related races. While at it also remove the
too-early clearing of allow_infinite_fallback in __mptcp_subflow_connect():
the field will be correctly cleared by subflow_finish_connect() if/when
the connection will complete successfully.
If fallback is not possible, as per RFC, reset the current subflow.
Since the fallback operation can now fail and return value should be
checked, rename the helper accordingly.
8c8492ca64e7 ("io_uring/net: don't retry connect operation on EPOLLERR")
is a little dirty hack that
1) wrongfully assumes that POLLERR equals to a failed request, which
breaks all POLLERR users, e.g. all error queue recv interfaces.
2) deviates the connection request behaviour from connect(2), and
3) racy and solved at a wrong level.
Nothing can be done with 2) now, and 3) is beyond the scope of the
patch. At least solve 1) by moving the hack out of generic poll handling
into io_connect().
In DCN401 pre-blending degamma LUT isn't affecting cursor as in previous
DCN version. As this is not the behavior close to what is expected for
CRTC degamma LUT, disable CRTC degamma LUT property in this HW.
Increment the reset counter only if soft recovery succeeded. This is
consistent with a ring hard reset behaviour where counter gets
incremented only if hard reset succeeded.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 25c314aa3ec3d30e4ee282540e2096b5c66a2437) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 42cdf6f687da ("drm/amdgpu/gfx8: always restore kcq MQDs") made the
ring pointer always to be reset on resume from suspend. This caused compute
rings to fail since the reset was done without also resetting it for the
firmware. Reset wptr on the GPU to avoid a disconnect between the driver
and firmware wptr.
Starting with Rust 1.89.0 (expected 2025-08-07), under
`CONFIG_RUST_DEBUG_ASSERTIONS=y`, `objtool` may report:
rust/kernel.o: warning: objtool: _R..._6kernel4pageNtB5_4Page8read_raw()
falls through to next function _R..._6kernel4pageNtB5_4Page9write_raw()
(and many others) due to calls to the `noreturn` symbol:
core::panicking::panic_nounwind_fmt
Thus add the mangled one to the list so that `objtool` knows it is
actually `noreturn`.
See commit 56d680dd23c3 ("objtool/rust: list `noreturn` Rust functions")
for more details.
Cc: stable@vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs). Cc: Josh Poimboeuf <jpoimboe@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/r/20250712160103.1244945-2-ojeda@kernel.org Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit e7186af7fb26 ("tracing: Add back FORTIFY_SOURCE logic to
kernel_stack event structure"), struct stack_entry marks its caller
field with __counted_by(size). At the time of the memcpy, entry->size
contains garbage from the ringbuffer, which under some circumstances is
zero, triggering a kernel panic by buffer overflow.
Populate the size field before the memcpy so that the out-of-bounds
check knows the correct size. This is analogous to
__ftrace_trace_stack().
Cc: stable@vger.kernel.org Cc: John Kacur <jkacur@redhat.com> Cc: Luis Goncalves <lgoncalv@redhat.com> Cc: Attila Fazekas <afazekas@redhat.com> Link: https://lore.kernel.org/20250716143601.7313-1-tglozar@redhat.com Fixes: e7186af7fb26 ("tracing: Add back FORTIFY_SOURCE logic to kernel_stack event structure") Signed-off-by: Tomas Glozar <tglozar@redhat.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a module is loaded, it adds trace events defined by the module. It
may also need to modify the modules trace printk formats to replace enum
names with their values.
If two modules are loaded at the same time, the adding of the event to the
ftrace_events list can corrupt the walking of the list in the code that is
modifying the printk format strings and crash the kernel.
The addition of the event should take the trace_event_sem for write while
it adds the new event.
Also add a lockdep_assert_held() on that semaphore in
__trace_add_event_dirs() as it iterates the list.
After a recent change in clang to strengthen uninitialized warnings [1],
it points out that in one of the error paths in parse_btf_arg(), params
is used uninitialized:
kernel/trace/trace_probe.c:660:19: warning: variable 'params' is uninitialized when used here [-Wuninitialized]
660 | return PTR_ERR(params);
| ^~~~~~
Match many other NO_BTF_ENTRY error cases and return -ENOENT, clearing
up the warning.
hid_hw_raw_request() is actually useful to ensure the provided buffer
and length are valid. Directly calling in the low level transport driver
function bypassed those checks and allowed invalid paramto be used.
Reported-by: Alan Stern <stern@rowland.harvard.edu> Closes: https://lore.kernel.org/linux-input/c75433e0-9b47-4072-bbe8-b1d14ea97b13@rowland.harvard.edu/ Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250710-report-size-null-v2-3-ccf922b7c4e5@kernel.org Signed-off-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The low level transport driver expects the first byte to be the report
ID, even when the report ID is not use (in which case they just shift
the buffer).
However, __hid_request() whas not offsetting the buffer it used by one
in this case, meaning that the raw_request() callback emitted by the
transport driver would be stripped of the first byte.
Note: this changes the API for uhid devices when a request is made
through hid_hw_request. However, several considerations makes me think
this is fine:
- every request to a HID device made through hid_hw_request() would see
that change, but every request made through hid_hw_raw_request()
already has the new behaviour. So that means that the users are
already facing situations where they might have or not the first byte
being the null report ID when it is 0. We are making things more
straightforward in the end.
- uhid is mainly used for BLE devices
- uhid is also used for testing, but I don't see that change a big issue
- for BLE devices, we can check which kernel module is calling
hid_hw_request()
- and in those modules, we can check which are using a Bluetooth device
- and then we can check if the command is used with a report ID or not.
- surprise: none of the kernel module are using a report ID 0
- and finally, bluez, in its function set_report()[0], does the same
shift if the report ID is 0 and the given buffer has a size > 0.
When the report ID is not used, the low level transport drivers expect
the first byte to be 0. However, currently the allocated buffer not
account for that extra byte, meaning that instead of having 8 guaranteed
bytes for implement to be working, we only have 7.
Reported-by: Alan Stern <stern@rowland.harvard.edu> Closes: https://lore.kernel.org/linux-input/c75433e0-9b47-4072-bbe8-b1d14ea97b13@rowland.harvard.edu/ Cc: stable@vger.kernel.org Suggested-by: Alan Stern <stern@rowland.harvard.edu> Link: https://patch.msgid.link/20250710-report-size-null-v2-1-ccf922b7c4e5@kernel.org Signed-off-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If "try_verify_in_tasklet" is set for dm-verity, DM_BUFIO_CLIENT_NO_SLEEP
is enabled for dm-bufio. However, when bufio tries to evict buffers, there
is a chance to trigger scheduling in spin_lock_bh, the following warning
is hit:
The current SPI framework does not verify if the SPI device supports
8 IO mode when doing an 8-bit transfer. This patch adds a check to
ensure that if the transfer tx_nbits or rx_nbits is 8, the SPI mode must
support 8 IO. If not, an error is returned, preventing undefined behavior.
Fixes: d6a711a898672 ("spi: Fix OCTAL mode support") Cc: stable@vger.kernel.org Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw> Link: https://patch.msgid.link/20250714031023.504752-1-linchengming884@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma_sync_sg_for_device() functions should be called with the same
nents as the dma_map_sg(), not the value the map function returned
according to the documentation in Documentation/core-api/dma-api.rst:450:
With the sync_sg API, all the parameters must be the same
as those passed into the sg mapping API.
On 11 Oct 2022, it was reported that the crc32 verification
of the u-boot environment failed only on big-endian systems
for the u-boot-env nvmem layout driver with the following error.
This problem has been present since the driver was introduced,
and before it was made into a layout driver.
The suggested fix at the time was to use further endianness
conversion macros in order to have both the stored and calculated
crc32 values to compare always represented in the system's endianness.
This was not accepted due to sparse warnings
and some disagreement on how to handle the situation.
Later on in a newer revision of the patch, it was proposed to use
cpu_to_le32() for both values to compare instead of le32_to_cpu()
and store the values as __le32 type to remove compilation errors.
The necessity of this is based on the assumption that the use of crc32()
requires endianness conversion because the algorithm uses little-endian,
however, this does not prove to be the case and the issue is unrelated.
Upon inspecting the current kernel code,
there already is an existing use of le32_to_cpu() in this driver,
which suggests there already is special handling for big-endian systems,
however, it is big-endian systems that have the problem.
This, being the only functional difference between architectures
in the driver combined with the fact that the suggested fix
was to use the exact same endianness conversion for the values
brings up the possibility that it was not necessary to begin with,
as the same endianness conversion for two values expected to be the same
is expected to be equivalent to no conversion at all.
After inspecting the u-boot environment of devices of both endianness
and trying to remove the existing endianness conversion,
the problem is resolved in an equivalent way as the other suggested fixes.
Ultimately, it seems that u-boot is agnostic to endianness
at least for the purpose of environment variables.
In other words, u-boot reads and writes the stored crc32 value
with the same endianness that the crc32 value is calculated with
in whichever endianness a certain architecture runs on.
Therefore, the u-boot-env driver does not need to convert endianness.
Remove the usage of endianness macros in the u-boot-env driver,
and change the type of local variables to maintain the same return type.
If there is a special situation in the case of endianness,
it would be a corner case and should be handled by a unique "compatible".
Even though it is not necessary to use endianness conversion macros here,
it may be useful to use them in the future for consistent error printing.
The commit "13bcd440f2ff nvmem: core: verify cell's raw_len" caused an
extension of the "mac-address" cell from 6 to 8 bytes due to word_size
of 4 bytes. This led to a required byte swap of the full buffer length,
which caused truncation of the mac-address when read.
Previously, the mac-address was incorrectly truncated from
70:B3:D5:14:E9:0E to 00:00:70:B3:D5:14.
Fix the issue by swapping only the first 6 bytes to correctly pass the
mac-address to the upper layers.
The commit 86bc88217006 ("staging: vchiq_arm: Create keep-alive thread
during probe") introduced a regression for certain configurations,
which doesn't have a VCHIQ user. This results in a unused and hanging
keep-alive thread:
INFO: task vchiq-keep/0:85 blocked for more than 120 seconds.
Not tainted 6.12.34-v8-+ #13
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:vchiq-keep/0 state:D stack:0 pid:85 tgid:85 ppid:2
Call trace:
__switch_to+0x188/0x230
__schedule+0xa54/0xb28
schedule+0x80/0x120
schedule_preempt_disabled+0x30/0x50
kthread+0xd4/0x1a0
ret_from_fork+0x10/0x20
The tb_dp_port_set_hops() function was incorrectly clearing
ADP_DP_CS_1_AUX_RX_HOPID_MASK twice. According to the function's
purpose, it should clear both TX and RX AUX HopID fields. Replace the
first instance with ADP_DP_CS_1_AUX_TX_HOPID_MASK to ensure proper
configuration of both AUX directions.
Fixes: 98176380cbe5 ("thunderbolt: Convert DP adapter register names to follow the USB4 spec") Cc: stable@vger.kernel.org Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a760d10ded37 ("thunderbolt: Fix a logic error in wake on connect")
fixated on the USB4 port sysfs wakeup file not working properly to control
policy, but it had an unintended side effect that the sysfs file controls
policy both at runtime and at suspend time. The sysfs file is supposed to
only control behavior while system is suspended.
Pass whether programming a port for runtime into usb4_switch_set_wake()
and if runtime then ignore the value in the sysfs file.
Cc: stable@vger.kernel.org Reported-by: Alexander Kovacs <Alexander.Kovacs@amd.com> Tested-by: Alexander Kovacs <Alexander.Kovacs@amd.com> Fixes: 1a760d10ded37 ("thunderbolt: Fix a logic error in wake on connect") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before each I2C transfer using DMA, the I2C buffer is DMA'pped to make
sure the memory buffer is DMA'able. This is handle in the function
`stm32_i2c_prep_dma_xfer()`.
If the transfer fails for any reason the I2C buffer must be unmap.
Use the dma_callback to factorize the code and fix this issue.
Note that the `stm32f7_i2c_dma_callback()` is now called in case of DMA
transfer success and error and that the `complete()` on the dma_complete
completion structure is done inconditionnally in case of transfer
success or error as well as the `dmaengine_terminate_async()`.
This is allowed as a `complete()` in case transfer error has no effect
as well as a `dmaengine_terminate_async()` on a transfer success.
Also fix the unneeded cast and remove not more needed variables.
If the DMA mapping failed, it produced an error log with the wrong
device name:
"stm32-dma3 40400000.dma-controller: rejecting DMA map of vmalloc memory"
Fix this issue by replacing the dev with the I2C dev.
When writing an empty string to either 'qw_sign' or 'landingPage'
sysfs attributes, the store functions attempt to access page[l - 1]
before validating that the length 'l' is greater than zero.
This patch fixes the vulnerability by adding a check at the beginning
of os_desc_qw_sign_store() and webusb_landingPage_store() to handle
the zero-length input case gracefully by returning immediately.
For UTMI+ PHY, according to programming guide, first should be set
PMUACTV bit then STOPPCLK bit. Otherwise, when the device issues
Remote Wakeup, then host notices disconnect instead.
For ULPI PHY, above mentioned bits must be set in reversed order:
STOPPCLK then PMUACTV.
When unplugging the USB cable or disconnecting a gadget in usb peripheral mode with
echo "" > /sys/kernel/config/usb_gadget/<your_gadget>/UDC,
/sys/class/udc/musb-hdrc.0/state does not change from USB_STATE_CONFIGURED.
Testing on dwc2/3 shows they both update the state to USB_STATE_NOTATTACHED.
Add calls to usb_gadget_set_state in musb_g_disconnect and musb_gadget_stop
to fix both cases.
Fixes: 49401f4169c0 ("usb: gadget: introduce gadget state tracking") Cc: stable@vger.kernel.org Co-authored-by: Yehowshua Immanuel <yehowshua.immanuel@twosixtech.com> Signed-off-by: Yehowshua Immanuel <yehowshua.immanuel@twosixtech.com> Signed-off-by: Drew Hamilton <drew.hamilton@zetier.com> Link: https://lore.kernel.org/r/20250701154126.8543-1-drew.hamilton@zetier.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NDI (Northern Digital Inc.) is introducing a new product called the
EMGUIDE GEMINI that will use an FTDI chip for USB serial communications.
Add the NDI EMGUIDE GEMINI product ID that uses the NDI Vendor ID
rather than the FTDI Vendor ID, unlike older products.
Signed-off-by: Ryan Mann <rmann@ndigital.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Periodic calibration updates (~10µs) may overlap with transfers when
PCIe NVMe SSD, LPDDR, and USB2 devices operate simultaneously, causing
crosstalk on Tegra234 devices. Hence disable periodic calibration updates
and make this a one-time calibration.
The logic that drives the pad calibration values resides in the
controller reset domain and so the calibration values are only being
captured when the controller is out of reset. However, by clearing the
CYA_TRK_CODE_UPDATE_ON_IDLE bit, the calibration values can be set
while the controller is in reset.
The CYA_TRK_CODE_UPDATE_ON_IDLE bit was previously cleared based on the
trk_hw_mode flag, but this dependency is not necessary. Instead,
introduce a new flag, trk_update_on_idle, to independently control this
bit.
When transitioning from USB_ROLE_DEVICE to USB_ROLE_NONE, the code
assumed that the regulator should be disabled. However, if the regulator
is marked as always-on, regulator_is_enabled() continues to return true,
leading to an incorrect attempt to disable a regulator which is not
enabled.
This can result in warnings such as:
[ 250.155624] WARNING: CPU: 1 PID: 7326 at drivers/regulator/core.c:3004
_regulator_disable+0xe4/0x1a0
[ 250.155652] unbalanced disables for VIN_SYS_5V0
To fix this, we move the regulator control logic into
tegra186_xusb_padctl_id_override() function since it's directly related
to the ID override state. The regulator is now only disabled when the role
transitions from USB_ROLE_HOST to USB_ROLE_NONE, by checking the VBUS_ID
register. This ensures that regulator enable/disable operations are
properly balanced and only occur when actually transitioning to/from host
mode.
Fixes: 49d46e3c7e59 ("phy: tegra: xusb: Add set_mode support for UTMI phy on Tegra186") Cc: stable@vger.kernel.org Signed-off-by: Wayne Chang <waynec@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20250502092606.2275682-1-waynec@nvidia.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VERW_CLEAR is supposed to be set only by the hypervisor to denote TSA
mitigation support to a guest. SQ_NO and L1_NO are both synthesizable,
and are going to be set by hw CPUID on future machines.
So keep the kvm_cpu_cap_init_kvm_defined() invocation *and* set them
when synthesized.
This fix is stable-only.
Co-developed-by: Jinpu Wang <jinpu.wang@ionos.com> Signed-off-by: Jinpu Wang <jinpu.wang@ionos.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rseq_cs field is documented as being set to 0 by user-space prior to
registration, however this is not currently enforced by the kernel. This
can result in a segfault on return to user-space if the value stored in
the rseq_cs field doesn't point to a valid struct rseq_cs.
The correct solution to this would be to fail the rseq registration when
the rseq_cs field is non-zero. However, some older versions of glibc
will reuse the rseq area of previous threads without clearing the
rseq_cs field and will also terminate the process if the rseq
registration fails in a secondary thread. This wasn't caught in testing
because in this case the leftover rseq_cs does point to a valid struct
rseq_cs.
What we can do is clear the rseq_cs field on registration when it's
non-zero which will prevent segfaults on registration and won't break
the glibc versions that reuse rseq areas on thread creation.
Herbert notes that DIV_ROUND_UP() may overflow unnecessarily if an ecdsa
implementation's ->key_size() callback returns an unusually large value.
Herbert instead suggests (for a division by 8):
X / 8 + !!(X & 7)
Based on this formula, introduce a generic DIV_ROUND_UP_POW2() macro and
use it in lieu of DIV_ROUND_UP() for ->key_size() return values.
Additionally, use the macro in ecc_digits_from_bytes(), whose "nbytes"
parameter is a ->key_size() return value in some instances, or a
user-specified ASN.1 length in the case of ecdsa_get_signature_rs().
We have a number of hwcaps for various SME subfeatures enumerated via
ID_AA64SMFR0_EL1. Currently we advertise these without cross checking
against the main SME feature, advertised in ID_AA64PFR1_EL1.SME which
means that if the two are out of sync userspace can see a confusing
situation where SME subfeatures are advertised without the base SME
hwcap. This can be readily triggered by using the arm64.nosme override
which only masks out ID_AA64PFR1_EL1.SME, and there have also been
reports of VMMs which do the same thing.
Fix this as we did previously for SVE in 064737920bdb ("arm64: Filter
out SVE hwcaps when FEAT_SVE isn't implemented") by filtering out the
SME subfeature hwcaps when FEAT_SME is not present.
Fixes: 5e64b862c482 ("arm64/sme: Basic enumeration support") Reported-by: Yury Khrustalev <yury.khrustalev@arm.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250620-arm64-sme-filter-hwcaps-v1-1-02b9d3c2d8ef@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to hardware limitations of NGBE, queue IRQs can only be requested
on vector 0 to 7. When the number of queues is set to the maximum 8,
the PCI IRQ vectors are allocated from 0 to 8. The vector 0 is used by
MISC interrupt, and althrough the vector 8 is used by queue interrupt,
it is unable to receive packets. This will cause some packets to be
dropped when RSS is enabled and they are assigned to queue 8.
So revert the adjustment of the MISC IRQ location, to make it be the
last one in IRQ vectors.
There may still exist some pcluster with valid reference counts
during unmounting. Instead of introducing another synchronization
primitive, just try again as unmounting is relatively rare. This
approach is similar to z_erofs_cache_invalidate_folio().
It was also reported by syzbot as a UAF due to commit f5ad9f9a603f
("erofs: free pclusters if no cached folio is attached"):
Ensure we don't stall or panic the kernel when using bluetooth-connected
controllers. This was reported as an issue on android devices using
kernel 6.6 due to the resume hook which had been added for usb joycons.
First, set a new state value to JOYCON_CTLR_STATE_SUSPENDED in a
newly-added nintendo_hid_suspend. This makes sure we will not stall out
the kernel waiting for input reports during led classdev suspend. The
stalls could happen if connectivity is unreliable or lost to the
controller prior to suspend.
Second, since we lose connectivity during suspend, do not try
joycon_init() for bluetooth controllers in the nintendo_hid_resume path.
Tested via multiple suspend/resume flows when using the controller both
in USB and bluetooth modes.
Signed-off-by: Daniel J. Ogorchock <djogorchock@gmail.com> Reviewed-by: Silvan Jegen <s.jegen@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Chicony Electronics HP 5MP Cameras (USB ID 04F2:B824 & 04F2:B82C)
report a HID sensor interface that is not actually implemented.
Attempting to access this non-functional sensor via iio_info causes
system hangs as runtime PM tries to wake up an unresponsive sensor.
Add these 2 devices to the HID ignore list since the sensor interface is
non-functional by design and should not be exposed to userspace.
MARTLINKTECHNOLOGY is a microphone device, when the HID interface in an
audio device is requested to get specific report id, the following error
may occur.
[ 562.939373] usb 1-1.4.1.2: new full-speed USB device number 21 using xhci_hcd
[ 563.104908] usb 1-1.4.1.2: New USB device found, idVendor=4c4a, idProduct=4155, bcdDevice= 1.00
[ 563.104910] usb 1-1.4.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 563.104911] usb 1-1.4.1.2: Product: USB Composite Device
[ 563.104912] usb 1-1.4.1.2: Manufacturer: SmartlinkTechnology
[ 563.104913] usb 1-1.4.1.2: SerialNumber: 20201111000001
[ 563.229499] input: SmartlinkTechnology USB Composite Device as /devices/pci0000:00/0000:00:07.1/0000:04:00.3/usb1/1-1/1-1.4/1-1.4.1/1-1.4.1.2/1-1.4.1.2:1.2/0003:4C4A:4155.000F/input/input35
[ 563.291505] hid-generic 0003:4C4A:4155.000F: input,hidraw2: USB HID v2.01 Keyboard [SmartlinkTechnology USB Composite Device] on usb-0000:04:00.3-1.4.1.2/input2
[ 563.291557] usbhid 1-1.4.1.2:1.3: couldn't find an input interrupt endpoint
[ 568.506654] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 573.626656] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 578.746657] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 583.866655] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 588.986657] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
Ignore HID interface. The device is working properly.
.rodata is implicitly included in the PT_DYNAMIC segment due to
inheriting the segment of the preceding .dynamic section (in both GNU ld
and LLD). When the .rodata section's size is not a multiple of 16
bytes on riscv64, llvm-readelf will report a "PT_DYNAMIC dynamic table
is invalid" warning. Note: in the presence of the .dynamic section, GNU
readelf and llvm-readelf's -d option decodes the dynamic section using
the section.
This issue arose after commit 8f8c1ff879fab60f80f3a7aec3000f47e5b03ba9
("riscv: vdso.lds.S: remove hardcoded 0x800 .text start addr"), which
placed .rodata directly after .dynamic by removing .eh_frame.
This patch resolves the implicit inclusion into PT_DYNAMIC by explicitly
specifying the :text output section phdr.
BPF_MAP_TYPE_LRU_HASH can recycle most recent elements well before the
map is full, due to percpu reservations and force shrink before
neighbor stealing. Once a CPU is unable to borrow from the global map,
it will once steal one elem from a neighbor and after that each time
flush this one element to the global list and immediately recycle it.
Batch value LOCAL_FREE_TARGET (128) will exhaust a 10K element map
with 79 CPUs. CPU 79 will observe this behavior even while its
neighbors hold 78 * 127 + 1 * 15 == 9921 free elements (99%).
CPUs need not be active concurrently. The issue can appear with
affinity migration, e.g., irqbalance. Each CPU can reserve and then
hold onto its 128 elements indefinitely.
Avoid global list exhaustion by limiting aggregate percpu caches to
half of map size, by adjusting LOCAL_FREE_TARGET based on cpu count.
This change has no effect on sufficiently large tables.
Similar to LOCAL_NR_SCANS and lru->nr_scans, introduce a map variable
lru->free_target. The extra field fits in a hole in struct bpf_lru.
The cacheline is already warm where read in the hot path. The field is
only accessed with the lru lock held.
Tested-by: Anton Protopopov <a.s.protopopov@gmail.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Stanislav Fomichev <sdf@fomichev.me> Link: https://lore.kernel.org/r/20250618215803.3587312-1-willemdebruijn.kernel@gmail.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This happens because we are processing an empty block group, which has
no extents allocated from it, there are no items for this block group,
including the block group item since block group items are stored in a
dedicated tree when using the block group tree feature. It also means
this is the block group with the highest start offset, so there are no
higher keys in the extent root, hence btrfs_search_slot_for_read()
returns 1 (no higher key found).
Fix this by asserting 'ret' is 0 only if the block group tree feature
is not enabled, in which case we should find a block group item for
the block group since it's stored in the extent root and block group
item keys are greater than extent item keys (the value for
BTRFS_BLOCK_GROUP_ITEM_KEY is 192 and for BTRFS_EXTENT_ITEM_KEY and
BTRFS_METADATA_ITEM_KEY the values are 168 and 169 respectively).
In case 'ret' is 1, we just need to add a record to the free space
tree which spans the whole block group, and we can achieve this by
making 'ret == 0' as the while loop's condition.
Reported-by: syzbot+36fae25c35159a763a2a@syzkaller.appspotmail.com Link: https://lore.kernel.org/linux-btrfs/6841dca8.a00a0220.d4325.0020.GAE@google.com/ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
MANA supports RDMA in PF mode. The driver should record the doorbell
physical address when in PF mode.
The doorbell physical address is used by the RDMA driver to map
doorbell pages of the device to user-mode applications through RDMA
verbs interface. In the past, they have been mapped to user-mode while
the device is in VF mode. With the support for PF mode implemented,
also expose those pages in PF mode.
Support for PF mode is implemented in 290e5d3c49f6 ("net: mana: Add support for Multi Vports on Bare metal")
Some modules have BT_EN enabled via a hardware pull-up,
meaning it is not defined in the DTS and is not controlled
through the power sequence. In such cases, fall through
to follow the legacy flow.
Signed-off-by: Shuai Zhang <quic_shuaz@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds DMI-based quirk for the Acer Nitro ANV15-41,
allowing the internal microphone to be detected correctly on
machines with "RB" as board vendor.
ASUS UM5606* models use the quirk to set up the bass speakers, but it
missed the mic-mute LED configuration. Other similar models have the
AMD ACP dmic, and the mic-mute is set up for that, but those models
don't have AMD ACP but rather built-in mics of Realtek codec, hence
the Realtek driver should set it up, instead.
When compiling with clang (19.1.7), initializing *vp using a compound
literal may result in excessive stack usage. Fix it by initializing the
required fields of *vp individually.
When transmitting an XDP_REDIRECT packet, call dma_unmap_len_set()
with the proper length instead of 0. This bug triggers this warning
on a system with IOMMU enabled:
In bnxt_ets_validate(), the code incorrectly loops over all possible
traffic classes to check and add the ETS settings. Fix it to loop
over the configured traffic classes only.
The unconfigured traffic classes will default to TSA_ETS with 0
bandwidth. Looping over these unconfigured traffic classes may
cause the validation to fail and trigger this error message:
"rejecting ETS config starving a TC\n"
The .ieee_setets() will then fail.
Fixes: 7df4ae9fe855 ("bnxt_en: Implement DCBNL to support host-based DCBX.") Reviewed-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Shravya KN <shravya.k-n@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20250710213938.1959625-2-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function ll_temac_ethtools_set_ringparam() incorrectly checked
rx_pending twice, once correctly for RX and once mistakenly in place
of tx_pending. This caused tx_pending to be left unchecked against
TX_BD_NUM_MAX.
As a result, invalid TX ring sizes may have been accepted or valid
ones wrongly rejected based on the RX limit, leading to potential
misconfiguration or unexpected results.
This patch corrects the condition to properly validate tx_pending.
Fixes: f7b261bfc35e ("net: ll_temac: Make RX/TX ring sizes configurable") Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com> Link: https://patch.msgid.link/20250710180621.2383000-1-alok.a.tiwari@oracle.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
An optimization for promiscuous mode adds a high-priority steering
table with a single catch-all rule to steer all traffic directly to
the TTC table.
However, a gap exists between the creation of this table and the
insertion of the catch-all rule. Packets arriving in this brief window
would miss as no rule was inserted yet, unnecessarily incrementing the
'rx_steer_missed_packets' counter and dropped.
This patch resolves the issue by introducing a new prio for this
table, placing it between MLX5E_TC_PRIO and MLX5E_NIC_PRIO. By doing
so, packets arriving during the window now fall through to the next
prio (at MLX5E_NIC_PRIO) instead of being dropped.
Fixes: 1c46d7409f30 ("net/mlx5e: Optimize promiscuous mode") Signed-off-by: Jianbo Liu <jianbol@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/1752155624-24095-4-git-send-email-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There's a race between disabling DIM and NAPI callbacks using the dim
pointer on the RQ or SQ.
If NAPI checks the DIM state bit and sees it still set, it assumes
`rq->dim` or `sq->dim` is valid. But if DIM gets disabled right after
that check, the pointer might already be set to NULL, leading to a NULL
pointer dereference in net_dim().
Fix this by calling `synchronize_net()` before freeing the DIM context.
This ensures all in-progress NAPI callbacks are finished before the
pointer is cleared.
I got the following warning when writing other tests:
+ handle_test_result_pass 'bond 802.3ad' '(lacp_active off)'
+ local 'test_name=bond 802.3ad'
+ shift
+ local 'opt_str=(lacp_active off)'
+ shift
+ log_test_result 'bond 802.3ad' '(lacp_active off)' ' OK '
+ local 'test_name=bond 802.3ad'
+ shift
+ local 'opt_str=(lacp_active off)'
+ shift
+ local 'result= OK '
+ shift
+ local retmsg=
+ shift
/net/tools/testing/selftests/net/forwarding/../lib.sh: line 315: shift: shift count out of range
This happens because an extra shift is executed even after all arguments
have been consumed. Remove the last shift in log_test_result() to avoid
this warning.
Fixes: a923af1ceee7 ("selftests: forwarding: Convert log_test() to recognize RET values") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://patch.msgid.link/20250709091244.88395-1-liuhangbin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Many net selftests invent their own logging helpers. These really should be
in a library sourced by these tests. Currently forwarding/lib.sh has a
suite of perfectly fine logging helpers, but sourcing a forwarding/ library
from a higher-level directory smells of layering violation. In this patch,
move the logging helpers to net/lib.sh so that every net test can use them.
Together with the logging helpers, it's also necessary to move
pause_on_fail(), and EXIT_STATUS and RET.
Existing lib.sh users might be using these same names for their functions
or variables. However lib.sh is always sourced near the top of the
file (checked), and whatever new definitions will simply override the ones
provided by lib.sh.
Restrict the 100Mbit forced-mode workaround to link-down transitions
only, to prevent repeated link reset cycles in certain configurations.
The workaround was originally introduced to improve signal reliability
when switching cables between long and short distances. It temporarily
forces the PHY into 10 Mbps before returning to 100 Mbps.
However, when used with autonegotiating link partners (e.g., Intel i350),
executing this workaround on every link change can confuse the partner
and cause constant renegotiation loops. This results in repeated link
down/up transitions and the PHY never reaching a stable state.
Limit the workaround to only run during the PHY_NOLINK state. This ensures
it is triggered only once per link drop, avoiding disruptive toggling
while still preserving its intended effect.
Note: I am not able to reproduce the original issue that this workaround
addresses. I can only confirm that 100 Mbit mode works correctly in my
test setup. Based on code inspection, I assume the workaround aims to
reset some internal state machine or signal block by toggling speeds.
However, a PHY reset is already performed earlier in the function via
phy_init_hw(), which may achieve a similar effect. Without a reproducer,
I conservatively keep the workaround but restrict its conditions.
Fixes: e57cf3639c32 ("net: lan78xx: fix accessing the LAN7800's internal phy specific registers from the MAC driver") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250709130753.3994461-3-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Enable .soft_reset for the LAN88xx PHY driver by assigning
genphy_soft_reset() to ensure that the phylib core performs a proper
soft reset during reconfiguration.
Previously, the driver left .soft_reset unimplemented, so calls to
phy_init_hw() (e.g., from lan88xx_link_change_notify()) did not fully
reset the PHY. As a result, stale contents in the Link Partner Ability
(LPA) register could persist, causing the PHY to incorrectly report
that the link partner advertised autonegotiation even when it did not.
Using genphy_soft_reset() guarantees a clean reset of the PHY and
corrects the false autoneg reporting in these scenarios.
Fixes: ccb989e4d1ef ("net: phy: microchip: Reset LAN88xx PHY to ensure clean link state on LAN7800/7850") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250709130753.3994461-2-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous hardcoded definitions of NUM_RX_STATS and
NUM_TX_STATS were not updated when new fields were added
to the ibmvnic_{rx,tx}_queue_stats structures. Specifically,
commit 2ee73c54a615 ("ibmvnic: Add stat for tx direct vs tx
batched") added a fourth TX stat, but NUM_TX_STATS remained 3,
leading to a mismatch.
This patch replaces the static defines with dynamic sizeof-based
calculations to ensure the stat arrays are correctly sized.
This fixes incorrect indexing and prevents incomplete stat
reporting in tools like ethtool.
Fixes: 2ee73c54a615 ("ibmvnic: Add stat for tx direct vs tx batched") Signed-off-by: Mingming Cao <mmc@linux.ibm.com> Reviewed-by: Dave Marquardt <davemarq@linux.ibm.com> Reviewed-by: Haren Myneni <haren@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250709153332.73892-1-mmc@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
