Post-2013 Lenovo laptops provide correct min/max dimensions, which are
different with the ones currently quirked. According to
https://bugzilla.kernel.org/show_bug.cgi?id=91541 the following board ids
are assigned in the post-2013 touchpads:
Using 2961 as the common minimum makes these 3 laptops OK. We may need
to update those values later if other pnp_ids has a lower board_id.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Add a min/max range for board ids to the min/max coordinates quirk. This
makes it possible to restrict quirks to specific models based upon their
board id. The define ANY_BOARD_ID (0) serves as a wild card.
Signed-off-by: Daniel Martin <daniel.martin@secunet.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The firmware of the X240 (LEN0035, 2013/12) exposes the same values
x [1232..5710], y [1156..4696]
as the quirk applies.
Signed-off-by: Daniel Martin <consume.noise@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
re-order the tests to check SYN_CAP_MIN_DIMENSIONS even on FW 8.1 Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Logging the dimension values we queried and the values we use from a quirk
to overwrite can be helpful for debugging.
This partly relates to bug:
https://bugzilla.kernel.org/show_bug.cgi?id=91541
Signed-off-by: Daniel Martin <consume.noise@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Split the function synaptics_resolution() into synaptics_resolution() and
synaptics_quirks(). synaptics_resolution() will be called before
synaptics_quirks() to query dimensions and resolutions before overwriting
them with quirks.
Signed-off-by: Daniel Martin <consume.noise@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Normally _regulator_do_enable() isn't called on an already-enabled
rdev. That's because the main caller, _regulator_enable() always
calls _regulator_is_enabled() and only calls _regulator_do_enable() if
the rdev was not already enabled.
However, there is one caller of _regulator_do_enable() that doesn't
check: regulator_suspend_finish(). While we might want to make
regulator_suspend_finish() behave more like _regulator_enable(), it's
probably also a good idea to make _regulator_do_enable() robust if it
is called on an already enabled rdev.
At the moment, _regulator_do_enable() is _not_ robust for already
enabled rdevs if we're using an ena_pin. Each time
_regulator_do_enable() is called for an rdev using an ena_pin the
reference count of the ena_pin is incremented even if the rdev was
already enabled. This is not as intended because the ena_pin is for
something else: for keeping track of how many active rdevs there are
sharing the same ena_pin.
Here's how the reference counting works here:
* Each time _regulator_enable() is called we increment
rdev->use_count, so _regulator_enable() calls need to be balanced
with _regulator_disable() calls.
* There is no explicit reference counting in _regulator_do_enable()
which is normally just a warapper around rdev->desc->ops->enable()
with code for supporting delays. It's not expected that the
"ops->enable()" call do reference counting.
* Since regulator_ena_gpio_ctrl() does have reference counting
(handling the sharing of the pin amongst multiple rdevs), we
shouldn't call it if the current rdev is already enabled.
Note that as part of this we cleanup (remove) the initting of
ena_gpio_state in regulator_register(). In _regulator_do_enable(),
_regulator_do_disable() and _regulator_is_enabled() is is clear that
ena_gpio_state should be the state of whether this particular rdev has
requested the GPIO be enabled. regulator_register() was initting it
as the actual state of the pin.
Fixes: 967cfb18c0e3 ("regulator: core: manage enable GPIO list") Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The _regulator_do_enable() call ought to be a no-op when called on an
already-enabled regulator. However, as an optimization
_regulator_enable() doesn't call _regulator_do_enable() on an already
enabled regulator. That means we never test the case of calling
_regulator_do_enable() during normal usage and there may be hidden
bugs or warnings. We have seen warnings issued by the tps65090 driver
and bugs when using the GPIO enable pin.
Let's match the same optimization that _regulator_enable() in
regulator_suspend_finish(). That may speed up suspend/resume and also
avoids exposing hidden bugs.
[Use much clearer commit message from Doug Anderson]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When inserting a new register into a block at the lower end the present
bitmap is currently shifted into the wrong direction. The effect of this is
that the bitmap becomes corrupted and registers which are present might be
reported as not present and vice versa.
Fix this by shifting left rather than right.
Fixes: 472fdec7380c("regmap: rbtree: Reduce number of nodes, take 2") Reported-by: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The SGTL5000_CHIP_ANA_POWER register is cached. Update the cached
value instead of writing it directly.
Patch inspired by Russell King's more colorful remarks in this
patch:
https://github.com/SolidRun/linux-imx6-3.14/commit/dd4bf6a
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Because prior GCC versions always emitted NOPs on ALIGN directives, but
gcc5 started omitting them.
.LSTARTFDEDLSI1 says:
/* HACK: The dwarf2 unwind routines will subtract 1 from the
return address to get an address in the middle of the
presumed call instruction. Since we didn't get here via
a call, we need to include the nop before the real start
to make up for it. */
.long .LSTART_sigreturn-1-. /* PC-relative start address */
But commit 69d0627a7f6e ("x86 vDSO: reorder vdso32 code") from 2.6.25
replaced .org __kernel_vsyscall+32,0x90 by ALIGN right before
__kernel_sigreturn.
Of course, ALIGN need not generate any NOP in there. Esp. gcc5 collapses
vclock_gettime.o and int80.o together with no generated NOPs as "ALIGN".
So fix this by adding to that point at least a single NOP and make the
function ALIGN possibly with more NOPs then.
Kudos for reporting and diagnosing should go to Richard.
Reported-by: Richard Biener <rguenther@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1425543211-12542-1-git-send-email-jslaby@suse.cz Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The interrupt is enabled before the handler is set. Even this bug
did not appear, it is potentially dangerous as it can lead to a
NULL pointer dereference.
Fix the error by enabling the interrupt after
clockevents_config_and_register() is called.
Signed-off-by: Yongbae Park <yongbae2@gmail.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The initialisation of the efm32 clocksource first sets up the irq and only
after that initialises the data needed for irq handling. In case this
initialisation is delayed the irq handler would dereference a NULL pointer.
I'm not aware of anything that could delay the process in such a way, but it's
better to be safe than sorry, so setup the irq only when the clock event device
is ready.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Yongbae Park <yongbae2@gmail.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
when multiport is off, virtio console invokes config access from irq
context, config access is blocking on s390.
Fix this up by scheduling work from config irq - similar to what we do
for multiport configs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
when multiport is off, we don't initialize config work,
but we then cancel uninitialized control_work on freeze.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Routes without a control must use NULL for the control name. The sn95031
driver uses "NULL" instead in a few places. Previous to commit 5fe5b767dc6f
("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets")
the DAPM core silently ignored non-NULL controls on non-mixer and non-mux
routes. But starting with that commit it will complain and not add the
route breaking the sn95031 driver in the process.
This patch replaces the incorrect "NULL" control name with NULL to fix the
issue.
Fixes: 5fe5b767dc6f ("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Routes without a control must use NULL for the control name. The da732x
driver uses "NULL" instead in a few places. Previous to commit 5fe5b767dc6f
("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets")
the DAPM core silently ignored non-NULL controls on non-mixer and non-mux
routes. But starting with that commit it will complain and not add the
route breaking the da732x driver in the process.
This patch replaces the incorrect "NULL" control name with NULL to fix the
issue.
Fixes: 5fe5b767dc6f ("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Routes without a control must use NULL for the control name. The ak4671
driver uses "NULL" instead in a few places. Previous to commit 5fe5b767dc6f
("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets")
the DAPM core silently ignored non-NULL controls on non-mixer and non-mux
routes. But starting with that commit it will complain and not add the
route breaking the ak4671 driver in the process.
This patch replaces the incorrect "NULL" control name with NULL to fix the
issue.
Fixes: 5fe5b767dc6f ("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Some APs experience problems when working with
U-APSD. Decreasing the probability of that
happening by using legacy mode for all ACs but VO
isn't enough.
Cisco 4410N originally forced us to enable VO by
default only because it treated non-VO ACs as
legacy.
However some APs (notably Netgear R7000) silently
reclassify packets to different ACs. Since u-APSD
ACs require trigger frames for frame retrieval
clients would never see some frames (e.g. ARP
responses) or would fetch them accidentally after
a long time.
It makes little sense to enable u-APSD queues by
default because it needs userspace applications to
be aware of it to actually take advantage of the
possible additional powersavings. Implicitly
depending on driver autotrigger frame support
doesn't make much sense.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The mesh forwarding path was not checking that data
frames were protected when running an encrypted network;
add the necessary check.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This updates the bit sliced AES module to the latest version in the
upstream OpenSSL repository (e620e5ae37bc). This is needed to fix a
bug in the XTS decryption path, where data chunked in a certain way
could trigger the ciphertext stealing code, which is not supposed to
be active in the kernel build (The kernel implementation of XTS only
supports round multiples of the AES block size of 16 bytes, whereas
the conformant OpenSSL implementation of XTS supports inputs of
arbitrary size by applying ciphertext stealing). This is fixed in
the upstream version by adding the missing #ifndef XTS_CHAIN_TWEAK
around the offending instructions.
The upstream code also contains the change applied by Russell to
build the code unconditionally, i.e., even if __LINUX_ARM_ARCH__ < 7,
but implemented slightly differently.
Fixes: e4e7f10bfc40 ("ARM: add support for bit sliced AES using NEON instructions") Reported-by: Adrian Kotelba <adrian.kotelba@gmail.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Tested-by: Milan Broz <gmazyland@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Since it's possible for the discard and write same queue limits to
change while the upper level command is being sliced and diced, fix up
both of them (a) to reject IO if the special command is unsupported at
the start of the function and (b) read the limits once and let the
commands error out on their own if the status happens to change.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The "dm snapshot: suspend origin when doing exception handover" commit
fixed a exception store handover bug associated with pending exceptions
to the "snapshot-origin" target.
However, a similar problem exists in snapshot merging. When snapshot
merging is in progress, we use the target "snapshot-merge" instead of
"snapshot-origin". Consequently, during exception store handover, we
must find the snapshot-merge target and suspend its associated
mapped_device.
To avoid lockdep warnings, the target must be suspended and resumed
without holding _origins_lock.
Introduce a dm_hold() function that grabs a reference on a
mapped_device, but unlike dm_get(), it doesn't crash if the device has
the DMF_FREEING flag set, it returns an error in this case.
In snapshot_resume() we grab the reference to the origin device using
dm_hold() while holding _origins_lock (_origins_lock guarantees that the
device won't disappear). Then we release _origins_lock, suspend the
device and grab _origins_lock again.
NOTE to stable@ people:
When backporting to kernels 3.18 and older, use dm_internal_suspend and
dm_internal_resume instead of dm_internal_suspend_fast and
dm_internal_resume_fast.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[ luis: backported to 3.16: as suggested by the author:
- replaced dm_internal_suspend_fast by dm_internal_suspend
- replaced dm_internal_resume_fast by dm_internal_resume ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In the function snapshot_resume we perform exception store handover. If
there is another active snapshot target, the exception store is moved
from this target to the target that is being resumed.
The problem is that if there is some pending exception, it will point to
an incorrect exception store after that handover, causing a crash due to
dm-snap-persistent.c:get_exception()'s BUG_ON.
This bug can be triggered by repeatedly changing snapshot permissions
with "lvchange -p r" and "lvchange -p rw" while there are writes on the
associated origin device.
To fix this bug, we must suspend the origin device when doing the
exception store handover to make sure that there are no pending
exceptions:
- introduce _origin_hash that keeps track of dm_origin structures.
- introduce functions __lookup_dm_origin, __insert_dm_origin and
__remove_dm_origin that manipulate the origin hash.
- modify snapshot_resume so that it calls dm_internal_suspend_fast() and
dm_internal_resume_fast() on the origin device.
NOTE to stable@ people:
When backporting to kernels 3.12-3.18, use dm_internal_suspend and
dm_internal_resume instead of dm_internal_suspend_fast and
dm_internal_resume_fast.
When backporting to kernels older than 3.12, you need to pick functions
dm_internal_suspend and dm_internal_resume from the commit fd2ed4d252701d3bbed4cd3e3d267ad469bb832a.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[ luis: backported to 3.16: as suggested by the author:
- replaced dm_internal_suspend_fast by dm_internal_suspend
- replaced dm_internal_resume_fast by dm_internal_resume ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
It was always intended that a read to an unprovisioned block will return
zeroes regardless of whether the pool is in read-only or read-write
mode. thin_bio_map() was inconsistent with its handling of such reads
when the pool is in read-only mode, it now properly zero-fills the bios
it returns in response to unprovisioned block reads.
Eliminate thin_bio_map()'s special read-only mode handling of -ENODATA
and just allow the IO to be deferred to the worker which will result in
pool->process_bio() handling the IO (which already properly zero-fills
reads to unprovisioned blocks).
Reported-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
While working on sk_forward_alloc problems reported by Denys
Fedoryshchenko, we found that tcp connect() (and fastopen) do not call
sk_wmem_schedule() for SYN packet (and/or SYN/DATA packet), so
sk_forward_alloc is negative while connect is in progress.
We can fix this by calling regular sk_stream_alloc_skb() both for the
SYN packet (in tcp_connect()) and the syn_data packet in
tcp_send_syn_data()
Then, tcp_send_syn_data() can avoid copying syn_data as we simply
can manipulate syn_data->cb[] to remove SYN flag (and increment seq)
Instead of open coding memcpy_fromiovecend(), simply use this helper.
This leaves in socket write queue clean fast clone skbs.
This was tested against our fastopen packetdrill tests.
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit db31c55a6fb2 (net: clamp ->msg_namelen instead of returning an
error) introduced the clamping of msg_namelen when the unsigned value
was larger than sizeof(struct sockaddr_storage). This caused a
msg_namelen of -1 to be valid. The native code was subsequently fixed by
commit dbb490b96584 (net: socket: error on a negative msg_namelen).
In addition, the native code sets msg_namelen to 0 when msg_name is
NULL. This was done in commit (6a2a2b3ae075 net:socket: set msg_namelen
to 0 if msg_name is passed as NULL in msghdr struct from userland) and
subsequently updated by 08adb7dabd48 (fold verify_iovec() into
copy_msghdr_from_user()).
This patch brings the get_compat_msghdr() in line with
copy_msghdr_from_user().
Fixes: db31c55a6fb2 (net: clamp ->msg_namelen instead of returning an error) Cc: David S. Miller <davem@davemloft.net> Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: used davem's backport to 3.14 ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
tcp_send_fin() does not account for the memory it allocates properly, so
sk_forward_alloc can be negative in cases where we've sent a FIN:
ss example output (ss -amn | grep -B1 f4294):
tcp FIN-WAIT-1 0 1 192.168.0.1:45520 192.0.2.1:8080
skmem:(r0,rb87380,t0,tb87380,f4294966016,w1280,o0,bl0) Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
for throw routes to trigger evaluation of other policy rules
EAGAIN needs to be propagated up to fib_rules_lookup
similar to how its done for IPv4
A simple testcase for verification is:
ip -6 rule add lookup 33333 priority 33333
ip -6 route add throw 2001:db8::1
ip -6 route add 2001:db8::1 via fe80::1 dev wlan0 table 33333
ip route get 2001:db8::1
Signed-off-by: Steven Barth <cyrus@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
[I would really like an ACK on that one from dhowells; it appears to be
quite straightforward, but...]
MSG_PEEK isn't passed to ->recvmsg() via msg->msg_flags; as the matter of
fact, neither the kernel users of rxrpc, nor the syscalls ever set that bit
in there. It gets passed via flags; in fact, another such check in the same
function is done correctly - as flags & MSG_PEEK.
It had been that way (effectively disabled) for 8 years, though, so the patch
needs beating up - that case had never been tested. If it is correct, it's
-stable fodder.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
It should be checking flags, not msg->msg_flags. It's ->sendmsg()
instances that need to look for that in ->msg_flags, ->recvmsg() ones
(including the other ->recvmsg() instance in that file, as well as
unix_dgram_recvmsg() this one claims to be imitating) check in flags.
Braino had been introduced in commit dcda13 ("caif: Bugfix - use MSG_TRUNC
in receive") back in 2010, so it goes quite a while back.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
inet_diag_dump_one_icsk() allocates too small skb.
Add inet_sk_attr_size() helper right before inet_sk_diag_fill()
so that it can be updated if/when new attributes are added.
iproute2/ss currently does not use this dump_one() interface,
this might explain nobody noticed this problem yet.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The rds_iw_update_cm_id function stores a large 'struct rds_sock' object
on the stack in order to pass a pair of addresses. This happens to just
fit withint the 1024 byte stack size warning limit on x86, but just
exceed that limit on ARM, which gives us this warning:
net/rds/iw_rdma.c:200:1: warning: the frame size of 1056 bytes is larger than 1024 bytes [-Wframe-larger-than=]
As the use of this large variable is basically bogus, we can rearrange
the code to not do that. Instead of passing an rds socket into
rds_iw_get_device, we now just pass the two addresses that we have
available in rds_iw_update_cm_id, and we change rds_iw_get_mr accordingly,
to create two address structures on the stack there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
sysctl has sysctl.net.core.rmem_*/wmem_* parameters which can be
set to incorrect values. Given that 'struct sk_buff' allocates from
rcvbuf, incorrectly set buffer length could result to memory
allocation failures. For example, set them as follows:
Moreover, the possible minimum is 1, so we can get another kernel panic:
...
BUG: unable to handle kernel paging request at ffff88013caee5c0
IP: [<ffffffff815604cf>] __alloc_skb+0x12f/0x1f0
...
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Firstly, handle zero length calls properly. Believe it or not there
are a few of these happening during early boot.
Next, we can't just drop to a memcpy() call in the forward copy case
where dst <= src. The reason is that the cache initializing stores
used in the Niagara memcpy() implementations can end up clearing out
cache lines before we've sourced their original contents completely.
For example, considering NG4memcpy, the main unrolled loop begins like
this:
Assume dst is 64 byte aligned and let's say that dst is src - 8 for
this memcpy() call. That store at the end there is the one to the
first line in the cache line, thus clearing the whole line, which thus
clobbers "src + 0x28" before it even gets loaded.
To avoid this, just fall through to a simple copy only mildly
optimized for the case where src and dst are 8 byte aligned and the
length is a multiple of 8 as well. We could get fancy and call
GENmemcpy() but this is good enough for how this thing is actually
used.
Reported-by: David Ahern <david.ahern@oracle.com> Reported-by: Bob Picco <bpicco@meloft.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
With the increase in number of CPUs calls to functions that dump
output to console (e.g., arch_trigger_all_cpu_backtrace) can take
a long time to complete. If IRQs are disabled eventually the NMI
watchdog kicks in and creates more havoc. Avoid by telling the NMI
watchdog everything is ok.
Signed-off-by: David Ahern <david.ahern@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The reason is that state is never reset (stays with PERF_HES_UPTODATE set).
Add a call to sparc_pmu_enable_event during the added_event handling.
Clean up the encoding since pmu_start calls sparc_pmu_enable_event which
does the same. Passing PERF_EF_RELOAD to sparc_pmu_start means the call
to sparc_perf_event_set_period can be removed as well.
With this patch:
$ perf stat ls
...
Performance counter stats for 'ls':
Signed-off-by: David Ahern <david.ahern@oracle.com> Acked-by: Bob Picco <bob.picco@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
perf_pmu_disable is called by core perf code before pmu->del and the
enable function is called by core perf code afterwards. No need to
call again within sparc_pmu_del.
Ditto for pmu->add and sparc_pmu_add.
Signed-off-by: David Ahern <david.ahern@oracle.com> Acked-by: Bob Picco <bob.picco@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
A bug was reported that the semtimedop() system call was always
failing eith ENOSYS.
Since SEMCTL is defined as 3, and SEMTIMEDOP is defined as 4,
the comparison "call <= SEMCTL" will always prevent SEMTIMEDOP
from getting through to the semaphore ops switch statement.
This is corrected by changing the comparison to "call <= SEMTIMEDOP".
Signed-off-by: Rob Gardner <rob.gardner@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Load balancing can be triggered in the critical sections protected by
srmmu_context_spinlock in destroy_context() and switch_mm() and can hang
the cpu waiting for the rq lock of another cpu that in turn has called
switch_mm hangning on srmmu_context_spinlock leading to deadlock.
So, disable interrupt while taking srmmu_context_spinlock in
destroy_context() and switch_mm() so we don't deadlock.
See also commit 77b838fa1ef0 ("[SPARC64]: destroy_context() needs to disable
interrupts.")
Signed-off-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Microsoft Natural Wireless Ergonomic Keyboard 7000 has special My
Favorites 1..5 keys which are handled through a vendor-defined usage
page (0xff05).
Apply MS_ERGONOMY quirks handling to USB PID 0x071d (Microsoft Microsoft
2.4GHz Transceiver V1.0) so that the My Favorites 1..5 keys are reported
as KEY_F14..18 events.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=52841 Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In order to support an older USB cradle by Denso, I added its vendor- and product-ID to the array of usb_device_id acm_ids. In this way cdc-acm feels responsible for this cradle. The related /dev/ttyACM node is being created properly, and the data transfer works.
However, later cradle models by Denso do have proper descriptors, so the patch is not required for these. At the same time both the older and the later model have the same vendor- and product-ID, but they both work with the patched driver.
Declaration of the Denso cradles I tested:
- both models have the same IDs: vendorID 0x076d, productID 0x0006
- older model: Denso CU-321 (descriptors not properly set)
- later model: Denso CU-821 (with proper descriptors)
Signed-off-by: Bjoern Gerhart <oss@airbjorn.de> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We need a pm_runtime_get_sync() call from
within musb_gadget_pullup() to make sure
registers are accessible at that time.
The problem is that musb_gadget_pullup() is
called with IRQs disabled and, because of that,
we need to tell pm_runtime that this pm_runtime_get_sync()
is IRQ safe.
We can simply add pm_runtime_irq_safe(), however, because
we need to make our read/write accessor function pointers
have been initialized before trying to use them. This means
that all pm_runtime initialization for musb_core needs to
be moved down so that when we call pm_runtime_irq_safe(),
the pm_runtime_get_sync() that it calls on the parent, won't
cause a crash due to NULL musb_read/write accessors.
Reported-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
f_phonet's ->set_alt() method will call usb_ep_disable()
potentially on an endpoint which is already disabled. That's
something the gadget/function driver must guarantee that it's
always balanced.
In order to balance the calls, just make sure the endpoint
was enabled before by means of checking the validity of
driver_data.
Reported-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
[ luis: backported to 3.16:
- file rename: drivers/usb/gadget/function/f_phonet.c ->
drivers/usb/gadget/f_phonet.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The FF2 driver (usbhid/hid-pidff.c) sends commands to the stick during ff_init.
However, this is called inside a block where driver_input_lock is locked, so
the results of these initial commands are discarded. This behavior is the
"killer", without this nothing else works.
ff_init issues commands using "hid_hw_request". This eventually goes to
hid_input_report, which returns -EBUSY because driver_input_lock is locked. The
change is to delay the ff_init call in hid-core.c until after this lock has
been released.
Calling hid_device_io_start() releases the lock so the device can be
configured. We also need to call hid_device_io_stop() on exit for the lock to
remain locked while ending the init of the drivers.
[ benjamin.tissoires@redhat.com: imrpoved the changelog a lot ]
Signed-off-by: Jim Keir <jimkeir@oracledbadirect.com> Reviewed-by: Benjamin.tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Surface Pro 3 Type Cover that works with Ubuntu (and possibly Arch) from this thread. Both trackpad and keyboard work after compiling my own kernel.
http://ubuntuforums.org/showthread.php?t=2231207&page=2&s=44910e0c56047e4f93dfd9fea58121ef
Also includes Jarrad Whitaker's message which sources
http://winaero.com/blog/how-to-install-linux-on-surface-pro-3/
which he says is sourced from a Russian site
Signed-off-by: Alan Wu <alan.c.wu@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Add support for Google devices that export simple serial
interfaces using the vendor specific SubClass/Protocol pair
0x50/0x01.
Signed-off-by: Anton Staaf <robotboy@chromium.org> Reviewed-by: Benson Leung <bleung@chromium.org>
[johan: move id entries and update Kconfig] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
It's an invalid approach to assume that among two divider values
the one nearer the exact divider is the better one.
Assume a parent rate of 1000 Hz, a divider with CLK_DIVIDER_POWER_OF_TWO
and a target rate of 89 Hz. The exact divider is ~ 11.236 so 8 and 16
are the candidates to choose from yielding rates 125 Hz and 62.5 Hz
respectivly. While 8 is nearer to 11.236 than 16 is, the latter is still
the better divider as 62.5 is nearer to 89 than 125 is.
Fixes: 774b514390b1 (clk: divider: Add round to closest divider) Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Maxime Coquelin <maxime.coquelin@st.com> Signed-off-by: Michael Turquette <mturquette@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The rate provided at the output of a clk-divider is calculated as:
DIV_ROUND_UP(parent_rate, div)
since commit b11d282dbea2 (clk: divider: fix rate calculation for
fractional rates). So to yield a rate not bigger than r parent_rate
must be <= r * div.
The effect of choosing a parent rate that is too big as was done before
this patch results in wrongly ruling out good dividers.
Note that this is not a complete fix as __clk_round_rate might return a
value >= its 2nd parameter. Also for dividers with
CLK_DIVIDER_ROUND_CLOSEST set the calculation is not accurate. But this
fixes the test case by Sascha Hauer that uses a chain of three dividers
under a fixed clock.
Fixes: b11d282dbea2 (clk: divider: fix rate calculation for fractional rates) Suggested-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Michael Turquette <mturquette@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 4da1c67719f61 ("add tbclk data for ehrpwm") Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 9e100ebafb91: ("Fix ehrpwm tbclk data") Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
at91rm9200 standby and suspend to ram has been broken since 00482a4078f4. It is wrongly using AT91_BASE_SYS which is a physical address
and actually doesn't correspond to any register on at91rm9200.
Use the correct at91_ramc_base[0] instead.
Fixes: 00482a4078f4 (ARM: at91: implement the standby function for pm/cpuidle) Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The current HDA generic parser initializes / modifies the amp values
always in stereo, but this seems causing the problem on ALC3229 codec
that has a few mono channel widgets: namely, these mono widgets react
to actions for both channels equally.
In the driver code, we do care the mono channel and create a control
only for the left channel (as defined in HD-audio spec) for such a
node. When the control is updated, only the left channel value is
changed. However, in the resume, the right channel value is also
restored from the initial value we took as stereo, and this overwrites
the left channel value. This ends up being the silent output as the
right channel has been never touched and remains muted.
This patch covers the places where unconditional stereo amp accesses
are done and converts to the conditional accesses.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94581 Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
According to a report from Yuxuan Shui, nilfs2 in kernel 3.19 got stuck
during recovery at mount time. The code path that caused the deadlock was
as follows:
nilfs_fill_super()
load_nilfs()
nilfs_salvage_orphan_logs()
* Do roll-forwarding, attach segment constructor for recovery,
and kick it.
nilfs_segctor_thread()
nilfs_segctor_thread_construct()
* A lock is held with nilfs_transaction_lock()
nilfs_segctor_do_construct()
nilfs_segctor_drop_written_files()
iput()
iput_final()
write_inode_now()
writeback_single_inode()
__writeback_single_inode()
do_writepages()
nilfs_writepage()
nilfs_construct_dsync_segment()
nilfs_transaction_lock() --> deadlock
This can happen if commit 7ef3ff2fea8b ("nilfs2: fix deadlock of segment
constructor over I_SYNC flag") is applied and roll-forward recovery was
performed at mount time. The roll-forward recovery can happen if datasync
write is done and the file system crashes immediately after that. For
instance, we can reproduce the issue with the following steps:
< nilfs2 is mounted on /nilfs (device: /dev/sdb1) >
# dd if=/dev/zero of=/nilfs/test bs=4k count=1 && sync
# dd if=/dev/zero of=/nilfs/test conv=notrunc oflag=dsync bs=4k
count=1 && reboot -nfh
< the system will immediately reboot >
# mount -t nilfs2 /dev/sdb1 /nilfs
The deadlock occurs because iput() can run segment constructor through
writeback_single_inode() if MS_ACTIVE flag is not set on sb->s_flags. The
above commit changed segment constructor so that it calls iput()
asynchronously for inodes with i_nlink == 0, but that change was
imperfect.
This fixes the another deadlock by deferring iput() in segment constructor
even for the case that mount is not finished, that is, for the case that
MS_ACTIVE flag is not set.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Reported-by: Yuxuan Shui <yshuiv7@gmail.com> Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
MacBook Air 5,2 has the same problem as MacBook Pro 8,1 where the
built-in mic records only the right channel. Apply the same
workaround as MBP8,1 to spread the mono channel via a Cirrus codec
vendor-specific COEF setup.
CS420x codecs seem to deal only the single amps of ADC nodes even
though the nodes receive multiple inputs. This leads to the
inconsistent amp value after S3/S4 resume, for example.
The fix is just to set codec->single_adc_amp flag. Then the driver
handles these ADC amps as if single connections.
This reverts commit e4df3a0b6228
("i2c: core: Dispose OF IRQ mapping at client removal time")
Calling irq_dispose_mapping() will destroy the mapping and disassociate
the IRQ from the IRQ chip to which it belongs. Keeping it is OK, because
existent mappings are reused properly.
Also, this commit breaks drivers using devm* for IRQ management on
OF-based systems because devm* cleanup happens in device code, after
bus's remove() method returns.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Reported-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[wsa: updated the commit message with findings fromt the other bug report] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Fixes: e4df3a0b6228
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The device complies to the UAC1 standard but hides that fact with
proprietary descriptors. The autodetect quirk for Roland devices
catches the audio interface but misses the MIDI part, so a specific
quirk is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org> Reported-by: Rafa Lafuente <rafalafuente@gmail.com> Tested-by: Raphaël Doursenaud <raphael@doursenaud.fr> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
There was no check about the id string of user control elements, so we
accepted even a control element with an empty string, which is
obviously bogus. This patch adds more sanity checks of id strings.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
To take down the MOB and GMR memory types, the driver may have to issue
fence objects and thus make sure that the fence manager is taken down
after those memory types.
Reorder device init accordingly.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Experimental lockdep annotation added to the TTM lock has unveiled a
couple of lock dependency violations in the vmwgfx driver. In both
cases it turns out that the device_private::reservation_sem is not
needed so the offending code is moved out of that lock.
Acked-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Compaq Presario CQ60 laptop with CX20561 gives a wrong pin for the
built-in mic NID 0x17 instead of NID 0x1d, and it results in the
non-working mic. This patch just remaps the pin correctly via fixup.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=920604 Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Otherwise the guest can abuse that control to cause e.g. PCIe
Unsupported Request responses by disabling memory and/or I/O decoding
and subsequently causing (CPU side) accesses to the respective address
ranges, which (depending on system configuration) may be fatal to the
host.
Note that to alter any of the bits collected together as
PCI_COMMAND_GUEST permissive mode is now required to be enabled
globally or on the specific device.
This is CVE-2015-2150 / XSA-120.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Some archs (specifically PowerPC), are sensitive with the ordering of
the enabling of the calls to function tracing and setting of the
function to use to be traced.
That is, update_ftrace_function() sets what function the ftrace_caller
trampoline should call. Some archs require this to be set before
calling ftrace_run_update_code().
Another bug was discovered, that ftrace_startup_sysctl() called
ftrace_run_update_code() directly. If the function the ftrace_caller
trampoline changes, then it will not be updated. Instead a call
to ftrace_startup_enable() should be called because it tests to see
if the callback changed since the code was disabled, and will
tell the arch to update appropriately. Most archs do not need this
notification, but PowerPC does.
The problem could be seen by the following commands:
When ftrace is enabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_START_FUNC_RET command to ftrace_run_update_code(). Similarly, when
ftrace is disabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_STOP_FUNC_RET command to ftrace_run_update_code().
Since ftrace_enabled = 0, ftrace_enable_ftrace_graph_caller() is never
called.
# echo 1 > /proc/sys/kernel/ftrace_enabled
Now ftrace_enabled will be set to true, but still
ftrace_enable_ftrace_graph_caller() will not be called, which is not
desired.
Further if we execute the following after this:
# echo nop > /sys/kernel/debug/tracing/current_tracer
Now since ftrace_enabled is set it will call
ftrace_disable_ftrace_graph_caller(), which causes a kernel warning on
the ARM platform.
On the ARM platform, when ftrace_enable_ftrace_graph_caller() is called,
it checks whether the old instruction is a nop or not. If it's not a nop,
then it returns an error. If it is a nop then it replaces instruction at
that address with a branch to ftrace_graph_caller.
ftrace_disable_ftrace_graph_caller() behaves just the opposite. Therefore,
if generic ftrace code ever calls either ftrace_enable_ftrace_graph_caller()
or ftrace_disable_ftrace_graph_caller() consecutively two times in a row,
then it will return an error, which will cause the generic ftrace code to
raise a warning.
Note, x86 does not have an issue with this because the architecture
specific code for ftrace_enable_ftrace_graph_caller() and
ftrace_disable_ftrace_graph_caller() does not check the previous state,
and calling either of these functions twice in a row has no ill effect.
The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.
The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.
Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Upon a URB submission failure, the driver calls usb_free_urb()
but then manually frees the URB buffer by itself. Meanwhile
usb_free_urb() has alredy freed out that transfer buffer since
we're the only code path holding a reference to this URB.
Remove two of such invalid manual free().
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient
this can lead to a skb_under_panic due to missing skb initialisations.
Add the missing initialisations at the CAN skbuff creation times on driver
level (rx path) and in the network layer (tx path).
Reported-by: Austin Schuh <austin@peloton-tech.com> Reported-by: Daniel Steer <daniel.steer@mclaren.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The commit [63e51fd708f5: ALSA: hda - Don't take unresponsive D3
transition too serious] introduced a conditional fallback behavior to
the HD-audio controller depending on the flag set. However, it
introduced a silly bug, too, that the flag was evaluated in a reverse
way. This resulted in a regression of HD-audio controller driver
where it can't go to the fallback mode at communication errors.
Unfortunately (or fortunately?) this didn't come up until recently
because the affected code path is an error handling that happens only
on an unstable hardware chip. Most of recent chips work stably, thus
they didn't hit this problem. Now, we've got a regression report with
a VIA chip, and this seems indeed requiring the fallback to the
polling mode, and finally the bug was revealed.
The fix is a oneliner to remove the wrong logical NOT in the check.
(Lesson learned - be careful about double negation.)
The bug should be backported to stable, but the patch won't be
applicable to 3.13 or earlier because of the code splits. The stable
fix patches for earlier kernels will be posted later manually.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94021 Fixes: 63e51fd708f5 ('ALSA: hda - Don't take unresponsive D3 transition too serious') Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
On the Cortex-A9-based Armada SoCs, the MPIC is not the primary interrupt
controller. Yet, it still has to handle some per-cpu interrupt.
To do so, it is chained with the GIC using a per-cpu interrupt. However, the
current code only call irq_set_chained_handler, which is called and enable that
interrupt only on the boot CPU, which means that the parent per-CPU interrupt
is never unmasked on the secondary CPUs, preventing the per-CPU interrupt to
actually work as expected.
This was not seen until now since the only MPIC PPI users were the Marvell
timers that were not working, but not used either since the system use the ARM
TWD by default, and the ethernet controllers, that are faking there interrupts
as SPI, and don't really expect to have interrupts on the secondary cores
anyway.
Add a CPU notifier that will enable the PPI on the secondary cores when they
are brought up.
It's directly caused by 89d3cf6 [SCSI] libsas: add mutex for SMP task
execution, but shows a deeper cause: expander functions expect to be able to
cast to and treat domain devices as expanders. The correct fix is to only do
expander discover when we know we've got an expander device to avoid wrongly
casting a non-expander device.
Reported-by: Praveen Murali <pmurali@logicube.com> Tested-by: Praveen Murali <pmurali@logicube.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Problem: When IMA and VTPM are both enabled in kernel config,
kernel hangs during bootup on LE OS.
Why?: IMA calls tpm_pcr_read() which results in tpm_ibmvtpm_send
and tpm_ibmtpm_recv getting called. A trace showed that
tpm_ibmtpm_recv was hanging.
Resolution: tpm_ibmtpm_recv was hanging because tpm_ibmvtpm_send
was sending CRQ message that probably did not make much sense
to phype because of Endianness. The fix below sends correctly
converted CRQ for LE. This was not caught before because it
seems IMA is not enabled by default in kernel config and
IMA exercises this particular code path in vtpm.
Tested with IMA and VTPM enabled in kernel config and VTPM
enabled on both a BE OS and a LE OS ppc64 lpar. This exercised
CRQ and TPM command code paths in vtpm.
Patch is against Peter's tpmdd tree on github which included
Vicky's previous vtpm le patches.
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com> Reviewed-by: Ashley Lai <ashley@ahsleylai.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit fd316941c ("spi/pl022: disable port when unused") introduced a race,
which leads to possible driver lock up (easily reproducible on SMP).
The problem happens in giveback() function where the completion of the transfer
is signalled to SPI subsystem and then the HW SPI controller is disabled. Another
transfer might be setup in between, which brings driver in locked-up state.
Lockup! SPI controller is disabled and the data will never be received. Whole
SPI subsystem is waiting for transfer ACK and blocked.
So, only signal transfer completion after disabling the controller.
Fixes: fd316941c (spi/pl022: disable port when unused) Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Using the pvops kernel a NULL pointer dereference was detected on a
large machine (144 processors) when booting as dom0 in
evtchn_fifo_unmask() during assignment of a pirq.
The event channel in question was the first to need a new entry in
event_array[] in events_fifo.c. Unfortunately xen_irq_info_pirq_setup()
is called with evtchn being 0 for a new pirq and the real event channel
number is assigned to the pirq only during __startup_pirq().
It is mandatory to call xen_evtchn_port_setup() after assigning the
event channel number to the pirq to make sure all memory needed for the
event channel is allocated.
Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
cancel[_delayed]_work_sync() are implemented using
__cancel_work_timer() which grabs the PENDING bit using
try_to_grab_pending() and then flushes the work item with PENDING set
to prevent the on-going execution of the work item from requeueing
itself.
try_to_grab_pending() can always grab PENDING bit without blocking
except when someone else is doing the above flushing during
cancelation. In that case, try_to_grab_pending() returns -ENOENT. In
this case, __cancel_work_timer() currently invokes flush_work(). The
assumption is that the completion of the work item is what the other
canceling task would be waiting for too and thus waiting for the same
condition and retrying should allow forward progress without excessive
busy looping
Unfortunately, this doesn't work if preemption is disabled or the
latter task has real time priority. Let's say task A just got woken
up from flush_work() by the completion of the target work item. If,
before task A starts executing, task B gets scheduled and invokes
__cancel_work_timer() on the same work item, its try_to_grab_pending()
will return -ENOENT as the work item is still being canceled by task A
and flush_work() will also immediately return false as the work item
is no longer executing. This puts task B in a busy loop possibly
preventing task A from executing and clearing the canceling state on
the work item leading to a hang.
task A task B worker
executing work
__cancel_work_timer()
try_to_grab_pending()
set work CANCELING
flush_work()
block for work completion
completion, wakes up A
__cancel_work_timer()
while (forever) {
try_to_grab_pending()
-ENOENT as work is being canceled
flush_work()
false as work is no longer executing
}
This patch removes the possible hang by updating __cancel_work_timer()
to explicitly wait for clearing of CANCELING rather than invoking
flush_work() after try_to_grab_pending() fails with -ENOENT.
Link: http://lkml.kernel.org/g/20150206171156.GA8942@axis.com
v3: bit_waitqueue() can't be used for work items defined in vmalloc
area. Switched to custom wake function which matches the target
work item and exclusive wait and wakeup.
v2: v1 used wake_up() on bit_waitqueue() which leads to NULL deref if
the target bit waitqueue has wait_bit_queue's on it. Use
DEFINE_WAIT_BIT() and __wake_up_bit() instead. Reported by Tomeu
Vizoso.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Rabin Vincent <rabin.vincent@axis.com> Cc: Tomeu Vizoso <tomeu.vizoso@gmail.com> Tested-by: Jesper Nilsson <jesper.nilsson@axis.com> Tested-by: Rabin Vincent <rabin.vincent@axis.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The cpuset.sched_relax_domain_level can control how far we do
immediate load balancing on a system. However, it was found on recent
kernels that echo'ing a value into cpuset.sched_relax_domain_level
did not reduce any immediate load balancing.
The reason this occurred was because the update_domain_attr_tree() traversal
did not update for the "top_cpuset". This resulted in nothing being changed
when modifying the sched_relax_domain_level parameter.
This patch is able to address that problem by having update_domain_attr_tree()
allow updates for the root in the cpuset traversal.
Fixes: fc560a26acce ("cpuset: replace cpuset->stack_list with cpuset_for_each_descendant_pre()") Signed-off-by: Jason Low <jason.low2@hp.com> Signed-off-by: Zefan Li <lizefan@huawei.com> Signed-off-by: Tejun Heo <tj@kernel.org> Tested-by: Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The NDDB register holds the data that are needed by the read and write
commands.
However, during a read PIO access, the datasheet specifies that after each 32
bytes read in that register, when BCH is enabled, we have to make sure that the
RDDREQ bit is set in the NDSR register.
This fixes an issue that was seen on the Armada 385, and presumably other mvebu
SoCs, when a read on a newly erased page would end up in the driver reporting a
timeout from the NAND.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Additionally to the current DMA transfer the PDC allows to set up a next DMA
transfer. This is useful for larger SPI transfers.
The driver currently waits for ENDRX as end of the transfer. But ENDRX is set
when the current DMA transfer is done (RCR = 0), i.e. it doesn't include the
next DMA transfer.
Thus a subsequent SPI transfer could be started although there is currently a
transfer in progress. This can cause invalid accesses to the SPI slave devices
and to SPI transfer errors.
This issue has been observed on a hardware with a M25P128 SPI NOR flash.
So instead of ENDRX we should wait for RXBUFF. This flag is set if there is
no more DMA transfer in progress (RCR = RNCR = 0).
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The commit d297933cc7fc (spi: dw: Fix detecting FIFO depth) tries to fix the
logic of the FIFO detection based on the description on the comments. However,
there is a slight difference between numbers in TX Level and TX FIFO size.
So, by specification the FIFO size would be in a range 2-256 bytes. From TX
Level prospective it means we can set threshold in the range 0-(FIFO size - 1)
bytes. Hence there are currently two issues:
a) FIFO size 2 bytes is actually skipped since TX Level is 1 bit and could be
either 0 or 1 byte;
b) FIFO size is incorrectly decreased by 1 which already done by meaning of
TX Level register.
This patch fixes it eventually right.
Fixes: d297933cc7fc (spi: dw: Fix detecting FIFO depth) Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When printing the driver_override parameter when it is 4095 and 4094 bytes
long, the printing code would access invalid memory because we need count+1
bytes for printing.
Fixes: 782a985d7af2 ("PCI: Introduce new device binding path using pci_dev.driver_override") Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Alex Williamson <alex.williamson@redhat.com> CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> CC: Alexander Graf <agraf@suse.de> CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
info is in network byte order, change it back to host byte order
before use. In particular, the current code sets the MTU of the tunnel
to a wrong (too big) value.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Currently qlge_update_hw_vlan_features() will always first put the
interface down, then update features and then bring it up again. But it
is possible to hit this code while the adapter is down and this causes a
non-paired call to napi_disable(), which will get stuck.
This patch fixes it by skipping these down/up actions if the interface
is already down.
Fixes: a45adbe8d352 ("qlge: Enhance nested VLAN (Q-in-Q) handling.") Cc: Harish Patil <harish.patil@qlogic.com> Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When creating a bpf classifier in tc with priority collisions and
invoking automatic unique handle assignment, cls_bpf_grab_new_handle()
will return a wrong handle id which in fact is non-unique. Usually
altering of specific filters is being addressed over major id, but
in case of collisions we result in a filter chain, where handle ids
address individual cls_bpf_progs inside the classifier.
Issue is, in cls_bpf_grab_new_handle() we probe for head->hgen handle
in cls_bpf_get() and in case we found a free handle, we're supposed
to use exactly head->hgen. In case of insufficient numbers of handles,
we bail out later as handle id 0 is not allowed.
Fixes: 7d1d65cb84e1 ("net: sched: cls_bpf: add BPF-based classifier") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In cls_bpf_modify_existing(), we read out the number of filter blocks,
do some sanity checks, allocate a block on that size, and copy over the
BPF instruction blob from user space, then pass everything through the
classic BPF checker prior to installation of the classifier.
We should reject mismatches here, there are 2 scenarios: the number of
filter blocks could be smaller than the provided instruction blob, so
we do a partial copy of the BPF program, and thus the instructions will
either be rejected from the verifier or a valid BPF program will be run;
in the other case, we'll end up copying more than we're supposed to,
and most likely the trailing garbage will be rejected by the verifier
as well (i.e. we need to fit instruction pattern, ret {A,K} needs to be
last instruction, load/stores must be correct, etc); in case not, we
would leak memory when dumping back instruction patterns. The code should
have only used nla_len() as Dave noted to avoid this from the beginning.
Anyway, lets fix it by rejecting such load attempts.
Fixes: 7d1d65cb84e1 ("net: sched: cls_bpf: add BPF-based classifier") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Sometimes while CPU have some load and ath5k doing the wireless
interface reset the whole WiSoC completely freezes. Set of tests shows
that using atomic delay function while we wait interface reset helps to
avoid such freezes.
The easiest way to reproduce this issue: create a station interface,
start continous scan with wpa_supplicant and load CPU by something. Or
just create multiple station interfaces and put them all in continous
scan.
This patch partially reverts the commit 1846ac3dbec0 ("ath5k: Use
usleep_range where possible"), which replaces initial udelay()
by usleep_range().
I do not know actual source of this issue, but all looks like that HW
freeze is caused by transaction on internal SoC bus, while wireless
block is in reset state.
Also I should note that I do not know how many chips are affected, but I
did not see this issue with chips, other than AR5312.
CC: Jiri Slaby <jirislaby@gmail.com> CC: Nick Kossifidis <mickflemm@gmail.com> CC: Luis R. Rodriguez <mcgrof@do-not-panic.com> Fixes: 1846ac3dbec0 ("ath5k: Use usleep_range where possible") Reported-by: Christophe Prevotaux <c.prevotaux@rural-networks.com> Tested-by: Christophe Prevotaux <c.prevotaux@rural-networks.com> Tested-by: Eric Bree <ebree@nltinc.com> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Our UC-KLEE tool found a kernel memory leak of 512 bytes (on x86_64) for
each call to gssp_accept_sec_context_upcall()
(net/sunrpc/auth_gss/gss_rpc_upcall.c). Since it appears that this call
can be triggered by remote connections (at least, from a cursory a
glance at the call chain), it may be exploitable to cause kernel memory
exhaustion. We found the bug in kernel 3.16.3, but it appears to date
back to commit 9dfd87da1aeb0fd364167ad199f40fe96a6a87be (2013-08-20).
The gssp_accept_sec_context_upcall() function performs a pair of calls
to gssp_alloc_receive_pages() and gssp_free_receive_pages(). The first
allocates memory for arg->pages. The second then frees the pages
pointed to by the arg->pages array, but not the array itself.
Reported-by: David A. Ramos <daramos@stanford.edu> Fixes: 9dfd87da1aeb ("rpc: fix huge kmalloc's in gss-proxy”) Signed-off-by: David A. Ramos <daramos@stanford.edu> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
projects / thirdparty / kernel / stable.git / log
