The irq_eoi() callback of the RZ/G2L interrupt chip clears the relevant
interrupt cause bit in the TSCR register by writing to it.
This write is not sufficient because the write is posted and therefore not
guaranteed to immediately clear the bit. Due to that delay the CPU can
raise the just handled interrupt again.
Prevent this by reading the register back which causes the posted write to
be flushed to the hardware before the read completes.
console_trylock_spinning() may takeover the console lock from a
schedulable context. Update @console_may_schedule to make sure it
reflects a trylock acquire.
Reported-by: Mukesh Ojha <quic_mojha@quicinc.com> Closes: https://lore.kernel.org/lkml/20240222090538.23017-1-quic_mojha@quicinc.com Fixes: dbdda842fe96 ("printk: Add console owner and waiter logic to load balance console writes") Signed-off-by: John Ogness <john.ogness@linutronix.de> Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/875xybmo2z.fsf@jogness.linutronix.de Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The swiotlb does not support a mapping size > swiotlb_max_mapping_size().
On the other hand, with a 64KB PAGE_SIZE configuration, it's observed that
an NVME device can map a size between 300KB~512KB, which certainly failed
the swiotlb mappings, though the default pool of swiotlb has many slots:
systemd[1]: Started Journal Service.
=> nvme 0000:00:01.0: swiotlb buffer is full (sz: 327680 bytes), total 32768 (slots), used 32 (slots)
note: journal-offline[392] exited with irqs disabled
note: journal-offline[392] exited with preempt_count 1
Since untrusted devices might go down the swiotlb pathway with dma-iommu,
these devices should not map a size larger than swiotlb_max_mapping_size.
To fix this bug, add iommu_dma_max_mapping_size() for untrusted devices to
take into account swiotlb_max_mapping_size() v.s. iova_rcache_range() from
the iommu_dma_opt_mapping_size().
Fixes: 82612d66d51d ("iommu: Allow the dma-iommu api to use bounce buffers") Link: https://lore.kernel.org/r/ee51a3a5c32cf885b18f6416171802669f4a718a.1707851466.git.nicolinc@nvidia.com Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
[will: Drop redundant is_swiotlb_active(dev) check] Signed-off-by: Will Deacon <will@kernel.org> Reviewed-by: Michael Kelley <mhklinux@outlook.com> Acked-by: Robin Murphy <robin.murphy@arm.com> Tested-by: Nicolin Chen <nicolinc@nvidia.com> Tested-by: Michael Kelley <mhklinux@outlook.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Nicolin reports that swiotlb buffer allocations fail for an NVME device
behind an IOMMU using 64KiB pages. This is because we end up with a
minimum allocation alignment of 64KiB (for the IOMMU to map the buffer
safely) but a minimum DMA alignment mask corresponding to a 4KiB NVME
page (i.e. preserving the 4KiB page offset from the original allocation).
If the original address is not 4KiB-aligned, the allocation will fail
because swiotlb_search_pool_area() erroneously compares these unmasked
bits with the 64KiB-aligned candidate allocation.
Tweak swiotlb_search_pool_area() so that the DMA alignment mask is
reduced based on the required alignment of the allocation.
Fixes: 82612d66d51d ("iommu: Allow the dma-iommu api to use bounce buffers") Link: https://lore.kernel.org/r/cover.1707851466.git.nicolinc@nvidia.com Reported-by: Nicolin Chen <nicolinc@nvidia.com> Signed-off-by: Will Deacon <will@kernel.org> Reviewed-by: Michael Kelley <mhklinux@outlook.com> Tested-by: Nicolin Chen <nicolinc@nvidia.com> Tested-by: Michael Kelley <mhklinux@outlook.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
core-api/dma-api-howto.rst states the following properties of
dma_alloc_coherent():
| The CPU virtual address and the DMA address are both guaranteed to
| be aligned to the smallest PAGE_SIZE order which is greater than or
| equal to the requested size.
However, swiotlb_alloc() passes zero for the 'alloc_align_mask'
parameter of swiotlb_find_slots() and so this property is not upheld.
Instead, allocations larger than a page are aligned to PAGE_SIZE,
Calculate the mask corresponding to the page order suitable for holding
the allocation and pass that to swiotlb_find_slots().
Fixes: e81e99bacc9f ("swiotlb: Support aligned swiotlb buffers") Signed-off-by: Will Deacon <will@kernel.org> Reviewed-by: Michael Kelley <mhklinux@outlook.com> Reviewed-by: Petr Tesarik <petr.tesarik1@huawei-partners.com> Tested-by: Nicolin Chen <nicolinc@nvidia.com> Tested-by: Michael Kelley <mhklinux@outlook.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit bbb73a103fbb ("swiotlb: fix a braino in the alignment check fix"),
which was a fix for commit 0eee5ae10256 ("swiotlb: fix slot alignment
checks"), causes a functional regression with vsock in a virtual machine
using bouncing via a restricted DMA SWIOTLB pool.
When virtio allocates the virtqueues for the vsock device using
dma_alloc_coherent(), the SWIOTLB search can return page-unaligned
allocations if 'area->index' was left unaligned by a previous allocation
from the buffer:
# Final address in brackets is the SWIOTLB address returned to the caller
| virtio-pci 0000:00:07.0: orig_addr 0x0 alloc_size 0x2000, iotlb_align_mask 0x800 stride 0x2: got slot 1645-1649/7168 (0x98326800)
| virtio-pci 0000:00:07.0: orig_addr 0x0 alloc_size 0x2000, iotlb_align_mask 0x800 stride 0x2: got slot 1649-1653/7168 (0x98328800)
| virtio-pci 0000:00:07.0: orig_addr 0x0 alloc_size 0x2000, iotlb_align_mask 0x800 stride 0x2: got slot 1653-1657/7168 (0x9832a800)
This ends badly (typically buffer corruption and/or a hang) because
swiotlb_alloc() is expecting a page-aligned allocation and so blindly
returns a pointer to the 'struct page' corresponding to the allocation,
therefore double-allocating the first half (2KiB slot) of the 4KiB page.
Fix the problem by treating the allocation alignment separately to any
additional alignment requirements from the device, using the maximum
of the two as the stride to search the buffer slots and taking care
to ensure a minimum of page-alignment for buffers larger than a page.
This also resolves swiotlb allocation failures occuring due to the
inclusion of ~PAGE_MASK in 'iotlb_align_mask' for large allocations and
resulting in alignment requirements exceeding swiotlb_max_mapping_size().
Fixes: bbb73a103fbb ("swiotlb: fix a braino in the alignment check fix") Fixes: 0eee5ae10256 ("swiotlb: fix slot alignment checks") Signed-off-by: Will Deacon <will@kernel.org> Reviewed-by: Michael Kelley <mhklinux@outlook.com> Reviewed-by: Petr Tesarik <petr.tesarik1@huawei-partners.com> Tested-by: Nicolin Chen <nicolinc@nvidia.com> Tested-by: Michael Kelley <mhklinux@outlook.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a probe is registered at the trace_sys_enter() tracepoint, and that
probe changes the system call number, the old system call still gets
executed. This worked correctly until commit b6ec41346103 ("core/entry:
Report syscall correctly for trace and audit"), which removed the
re-evaluation of the syscall number after the trace point.
Restore the original semantics by re-evaluating the system call number
after trace_sys_enter().
The performance impact of this re-evaluation is minimal because it only
takes place when a trace point is active, and compared to the actual trace
point overhead the read from a cache hot variable is negligible.
Fixes: b6ec41346103 ("core/entry: Report syscall correctly for trace and audit") Signed-off-by: André Rösti <an.roesti@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240311211704.7262-1-an.roesti@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit a4d5613c4dc6 ("arm: extend pfn_valid to take into account
freed memory map alignment") changes the semantics of pfn_valid() to check
presence of the memory map for a PFN. A valid page for an address which
is reserved but not mapped by the kernel[1], the system crashed during
some uio test with the following memory layout:
Unable to handle kernel paging request at virtual address bff00000
[...]
CPU: 1 PID: 465 Comm: startapp.bin Tainted: G O 5.10.0 #1
Hardware name: Generic DT based system
PC is at b15_flush_kern_dcache_area+0x24/0x3c
LR is at __sync_icache_dcache+0x6c/0x98
[...]
(b15_flush_kern_dcache_area) from (__sync_icache_dcache+0x6c/0x98)
(__sync_icache_dcache) from (set_pte_at+0x28/0x54)
(set_pte_at) from (remap_pfn_range+0x1a0/0x274)
(remap_pfn_range) from (uio_mmap+0x184/0x1b8 [uio])
(uio_mmap [uio]) from (__mmap_region+0x264/0x5f4)
(__mmap_region) from (__do_mmap_mm+0x3ec/0x440)
(__do_mmap_mm) from (do_mmap+0x50/0x58)
(do_mmap) from (vm_mmap_pgoff+0xfc/0x188)
(vm_mmap_pgoff) from (ksys_mmap_pgoff+0xac/0xc4)
(ksys_mmap_pgoff) from (ret_fast_syscall+0x0/0x5c)
Code: e0801001e2423001e1c00003f57ff04f (ee070f3e)
---[ end trace 09cf0734c3805d52 ]---
Kernel panic - not syncing: Fatal exception
So check if PG_reserved was set to solve this issue.
Fixes: a4d5613c4dc6 ("arm: extend pfn_valid to take into account freed memory map alignment") Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Yongqiang Liu <liuyongqiang13@huawei.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
PJ4 is a v7 core that incorporates a iWMMXt coprocessor. However, GCC
does not support this combination (its iWMMXt configuration always
implies v5te), and so there is no v6/v7 user space that actually makes
use of this, beyond generic support for things like setjmp() that
preserve/restore the iWMMXt register file using generic LDC/STC
instructions emitted in assembler. As [0] appears to imply, this logic
is triggered for the init process at boot, and so most user threads will
have a iWMMXt register context associated with it, even though it is
never used.
At this point, it is highly unlikely that such GCC support will ever
materialize (and Clang does not implement support for iWMMXt to begin
with).
This means that advertising iWMMXt support on these cores results in
context switch overhead without any associated benefit, and so it is
better to simply ignore the iWMMXt unit on these systems. So rip out the
support. Doing so also fixes the issue reported in [0] related to UNDEF
handling of co-processor #0/#1 instructions issued from user space
running in Thumb2 mode.
The PJ4 cores are used in four platforms: Armada 370/xp, Dove (Cubox,
d2plug), MMP2 (xo-1.75) and Berlin (Google TV). Out of these, only the
first is still widely used, but that one actually doesn't have iWMMXt
but instead has only VFPV3-D16, and so it is not impacted by this
change.
The prescaler in the "Global Timer Control Register bit assignments" is
documented to use bits [15:8], which means that the maximum prescaler
register value is 0xff.
The early startup code executes from a 1:1 mapping of memory, which
differs from the mapping that the code was linked and/or relocated to
run at. The latter mapping is not active yet at this point, and so
symbol references that rely on it will fault.
Given that the core kernel is built without -fPIC, symbol references are
typically emitted as absolute, and so any such references occuring in
the early startup code will therefore crash the kernel.
While an attempt was made to work around this for the early SEV/SME
startup code, by forcing RIP-relative addressing for certain global
SEV/SME variables via inline assembly (see snp_cpuid_get_table() for
example), RIP-relative addressing must be pervasively enforced for
SEV/SME global variables when accessed prior to page table fixups.
__startup_64() already handles this issue for select non-SEV/SME global
variables using fixup_pointer(), which adjusts the pointer relative to a
`physaddr` argument. To avoid having to pass around this `physaddr`
argument across all functions needing to apply pointer fixups, introduce
a macro RIP_RELATIVE_REF() which generates a RIP-relative reference to
a given global variable. It is used where necessary to force
RIP-relative accesses to global variables.
For backporting purposes, this patch makes no attempt at cleaning up
other occurrences of this pattern, involving either inline asm or
fixup_pointer(). Those will be addressed later.
[ bp: Call it "rip_rel_ref" everywhere like other code shortens
"rIP-relative reference" and make the asm wrapper __always_inline. ]
Mukunda Vijendar [1] points out that revision 0x63 is Pink
Sardine platform, not Yellow Carp. The YC driver should not
be enabled for this platform. This patch prevents the YC
driver from being incorrectly enabled.
Although the microphone functioned with the YC driver, it
resulted in incorrect driver usage. The Lenovo 21J2 is not a
Yellow Carp platform, but a Pink Sardine platform, which
already has an upstreamed driver.
The microphone on the Lenovo 21J2 operates correctly with the
CONFIG_SND_SOC_AMD_PS flag enabled and does not require the
quirk entry. So this patch removes the quirk entry.
Thanks to Mukunda Vijendar [1] for pointing this out.
Normally, the EFI stub calls into the EFI boot services using the stack
that was live when the stub was entered. According to the UEFI spec,
this stack needs to be at least 128k in size - this might seem large but
all asynchronous processing and event handling in EFI runs from the same
stack and so quite a lot of space may be used in practice.
In mixed mode, the situation is a bit different: the bootloader calls
the 32-bit EFI stub entry point, which calls the decompressor's 32-bit
entry point, where the boot stack is set up, using a fixed allocation
of 16k. This stack is still in use when the EFI stub is started in
64-bit mode, and so all calls back into the EFI firmware will be using
the decompressor's limited boot stack.
Due to the placement of the boot stack right after the boot heap, any
stack overruns have gone unnoticed. However, commit
5c4feadb0011983b ("x86/decompressor: Move global symbol references to C code")
moved the definition of the boot heap into C code, and now the boot
stack is placed right at the base of BSS, where any overruns will
corrupt the end of the .data section.
While it would be possible to work around this by increasing the size of
the boot stack, doing so would affect all x86 systems, and mixed mode
systems are a tiny (and shrinking) fraction of the x86 installed base.
So instead, record the firmware stack pointer value when entering from
the 32-bit firmware, and switch to this stack every time a EFI boot
service call is made.
This reverts commit 16ab7cb5825fc3425c16ad2c6e53d827f382d7c6 because it
broke iwd. iwd uses the KEYCTL_PKEY_* UAPIs via its dependency libell,
and apparently it is relying on SHA-1 signature support. These UAPIs
are fairly obscure, and their documentation does not mention which
algorithms they support. iwd really should be using a properly
supported userspace crypto library instead. Regardless, since something
broke we have to revert the change.
It may be possible that some parts of this commit can be reinstated
without breaking iwd (e.g. probably the removal of MODULE_SIG_SHA1), but
for now this just does a full revert to get things working again.
Reported-by: Karel Balej <balejk@matfyz.cz> Closes: https://lore.kernel.org/r/CZSHRUIJ4RKL.34T4EASV5DNJM@matfyz.cz Cc: Dimitri John Ledkov <dimitri.ledkov@canonical.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Tested-by: Karel Balej <balejk@matfyz.cz> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This set combination is weird: it allows for elements to be
added/deleted, but once bound to the rule it cannot be updated anymore.
Eventually, all elements expire, leading to an empty set which cannot
be updated anymore. Reject this flags combination.
Cc: stable@vger.kernel.org Fixes: 761da2935d6e ("netfilter: nf_tables: add set timeout API support") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The monitor shipped with the Framework 16 supports VRR [1], but it's not
being advertised.
This is because the detailed timing block doesn't contain
`EDID_DETAIL_MONITOR_RANGE` which amdgpu looks for to find min and max
frequencies. This check however is superfluous for this case because
update_display_info() calls drm_get_monitor_range() to get these ranges
already.
So if the `DRM_EDID_FEATURE_CONTINUOUS_FREQ` EDID feature is found then
turn on freesync without extra checks.
v2: squash in fix from Harry
Closes: https://www.reddit.com/r/framework/comments/1b4y2i5/no_variable_refresh_rate_on_the_framework_16_on/ Closes: https://www.reddit.com/r/framework/comments/1b6vzcy/framework_16_variable_refresh_rate/ Closes: https://community.frame.work/t/resolved-no-vrr-freesync-with-amd-version/42338 Link: https://gist.github.com/superm1/e8fbacfa4d0f53150231d3a3e0a13faf Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have set the WQ_NAME_LEN to 32, decrease the name of
events_freezable_power_efficient so that it does not trip the name length
warning when the workqueue is created.
This reverts commit 340383c734f8 ("drm/amd/display: Remove pixle rate
limit for subvp")
[why]
The original commit causes a regression when subvp is applied
on ODM required 8k60hz timing. The display shows black screen
on boot. The issue can be recovered with hotplug. It also causes
MPO to fail. We will temprarily revert this commit and investigate
the root cause further.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com> Reviewed-by: Martin Leung <martin.leung@amd.com> Acked-by: Wayne Lin <wayne.lin@amd.com> Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A vulnerability exists where the eventfd for INTx signaling can be
deconfigured, which unregisters the IRQ handler but still allows
eventfds to be signaled with a NULL context through the SET_IRQS ioctl
or through unmask irqfd if the device interrupt is pending.
Ideally this could be solved with some additional locking; the igate
mutex serializes the ioctl and config space accesses, and the interrupt
handler is unregistered relative to the trigger, but the irqfd path
runs asynchronous to those. The igate mutex cannot be acquired from the
atomic context of the eventfd wake function. Disabling the irqfd
relative to the eventfd registration is potentially incompatible with
existing userspace.
As a result, the solution implemented here moves configuration of the
INTx interrupt handler to track the lifetime of the INTx context object
and irq_type configuration, rather than registration of a particular
trigger eventfd. Synchronization is added between the ioctl path and
eventfd_signal() wrapper such that the eventfd trigger can be
dynamically updated relative to in-flight interrupts or irqfd callbacks.
In order to synchronize changes that can affect the thread callback,
introduce an interface to force a flush of the inject workqueue. The
irqfd pointer is only valid under spinlock, but the workqueue cannot
be flushed under spinlock. Therefore the flush work for the irqfd is
queued under spinlock. The vfio_irqfd_cleanup_wq workqueue is re-used
for queuing this work such that flushing the workqueue is also ordered
relative to shutdown.
Reviewed-by: Kevin Tian <kevin.tian@intel.com> Reviewed-by: Reinette Chatre <reinette.chatre@intel.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Link: https://lore.kernel.org/r/20240308230557.805580-4-alex.williamson@redhat.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Stable-dep-of: 18c198c96a81 ("vfio/pci: Create persistent INTx handler") Signed-off-by: Sasha Levin <sashal@kernel.org>
[CAUSE]
We only do a very basic size check for btrfs_qgroup_inherit structure,
but never really verify if the values are correct.
Thus in btrfs_qgroup_inherit() function, we have to skip non-existing
qgroups, and never return any error.
[FIX]
Fix the behavior and introduce extra checks:
- Introduce early check for btrfs_qgroup_inherit structure
Not only the size, but also all the qgroup ids would be verified.
And the timing is very early, so we can return error early.
This early check is very important for snapshot creation, as snapshot
is delayed to transaction commit.
- Drop support for btrfs_qgroup_inherit::num_ref_copies and
num_excl_copies
Those two members are used to specify to copy refr/excl numbers from
other qgroups.
This would definitely mark qgroup inconsistent, and btrfs-progs has
dropped the support for them for a long time.
It's time to drop the support for kernel.
- Verify the supported btrfs_qgroup_inherit::flags
Just in case we want to add extra flags for btrfs_qgroup_inherit.
Now above subvolume creation would fail with -ENOENT other than silently
ignore the non-existing qgroup.
CC: stable@vger.kernel.org # 6.7+ Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a convenience helper to get a fs_info from a VFS inode pointer
instead of open coding the chain or using btrfs_sb() that in some cases
does one more pointer hop. This is implemented as a macro (still with
type checking) so we don't need full definitions of struct btrfs_inode,
btrfs_root or btrfs_fs_info.
Add convenience helpers to get a fs_info from a page or folio pointer
instead of open coding the chain or using btrfs_sb() that in some cases
does one more pointer hop. This is implemented as a macro (still with
type checking) so we don't need full definitions of struct page, folio,
btrfs_root and btrfs_fs_info. The latter can't be static inlines as this
would create loop between ctree.h <-> fs.h, or the headers would have to
be restructured.
Add convenience helpers to get a struct btrfs_inode from a page or folio
pointer instead of open coding the chain or intermediate BTRFS_I. This
is implemented as a macro (still with type checking) so we don't need
full definitions of struct page or address_space.
The block size stored in the super block is used by subsystems outside
of btrfs and it's a copy of fs_info::sectorsize. Unify that to always
use our sectorsize, with the exception of mount where we first need to
use fixed values (4K) until we read the super block and can set the
sectorsize.
Replace all uses, in most cases it's fewer pointer indirections.
Turn set_page_extent_mapped() into a wrapper around this version.
Saves a call to compound_head() for callers who already have a folio
and removes a couple of users of page->mapping.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Stable-dep-of: 86211eea8ae1 ("btrfs: qgroup: validate btrfs_qgroup_inherit parameter") Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Any interface that touches registers needs to wake up the system.
[How]
Add a new interface dc_exit_ips_for_hw_access that wraps the check
for IPS support and insert it into the public DC interfaces that
touch registers.
We don't re-enter, since we expect that the enter/exit to have been done
on the DM side.
Cc: stable@vger.kernel.org # 6.1+ Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com> Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
There is only a single call to dc_post_update_surfaces_to_stream
so there is no need to have two flags to control it. Unifying
this to a single flag allows dc_stream_adjust_vmin_vmax to skip
actual programming when there is no change required.
[how]
Remove wm_optimze_required flag and set only optimize_required in its
place. Then in dc_stream_adjust_vmin_vmax, check that the stream timing
range matches the requested one and skip programming if they are equal.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Acked-by: Tom Chung <chiahsuan.chung@amd.com> Signed-off-by: Aric Cyr <aric.cyr@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: a9b1a4f684b3 ("drm/amd/display: Add more checks for exiting idle in DC") Signed-off-by: Sasha Levin <sashal@kernel.org>
Some drivers require the mapped tt pages to be decrypted. In an ideal
world this would have been handled by the dma layer, but the TTM page
fault handling would have to be rewritten to able to do that.
A side-effect of the TTM page fault handling is using a dma allocation
per order (via ttm_pool_alloc_page) which makes it impossible to just
trivially use dma_mmap_attrs. As a result ttm has to be very careful
about trying to make its pgprot for the mapped tt pages match what
the dma layer thinks it is. At the ttm layer it's possible to
deduce the requirement to have tt pages decrypted by checking
whether coherent dma allocations have been requested and the system
is running with confidential computing technologies.
This approach isn't ideal but keeping TTM matching DMAs expectations
for the page properties is in general fragile, unfortunately proper
fix would require a rewrite of TTM's page fault handling.
Fixes vmwgfx with SEV enabled.
v2: Explicitly include cc_platform.h
v3: Use CC_ATTR_GUEST_MEM_ENCRYPT instead of CC_ATTR_MEM_ENCRYPT to
limit the scope to guests and log when memory decryption is enabled.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com> Fixes: 3bf3710e3718 ("drm/ttm: Add a generic TTM memcpy move for page-based iomem") Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> Acked-by: Christian König <christian.koenig@amd.com> Cc: Huang Rui <ray.huang@amd.com> Cc: dri-devel@lists.freedesktop.org Cc: linux-kernel@vger.kernel.org Cc: <stable@vger.kernel.org> # v5.14+ Link: https://patchwork.freedesktop.org/patch/msgid/20230926040359.3040017-1-zack@kde.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Using the WSEC command instead of sae_password seems to be the supported
mechanism on newer firmware, and also how the brcmdhd driver does it.
The existing firmware mechanism intended for (some) Cypress chips has
been separated from the new firmware mechanism using the multi-vendor
framework. Depending on the device it will select the appropriate
firmware mechanism.
This makes WPA3 work with iwd, or with wpa_supplicant pending a support
patchset [2].
Adding a .feat_attach() callback allowing per-vendor overrides
of the driver feature flags. In this patch the callback is only
provided by BCA vendor to disable SAE feature as it has not been
confirmed yet. BCA chips generally do not have the in-driver
supplicant (idsup) feature so they rely on NL80211_CMD_EXTERNAL_AUTH
to trigger user-space authentication.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20240103095704.135651-3-arend.vanspriel@broadcom.com
Stable-dep-of: 85da8f71aaa7 ("wifi: brcmfmac: Demote vendor-specific attach/detach messages to info") Signed-off-by: Sasha Levin <sashal@kernel.org>
7ee18d677989 ("x86/power: Make restore_processor_context() sane")
kmemleak reports this issue:
unreferenced object 0xf68241e0 (size 32):
comm "swapper/0", pid 1, jiffies 4294668610 (age 68.432s)
hex dump (first 32 bytes):
00 cc cc cc 29 10 01 c0 00 00 00 00 00 00 00 00 ....)...........
00 42 82 f6 cc cc cc cc cc cc cc cc cc cc cc cc .B..............
backtrace:
[<461c1d50>] __kmem_cache_alloc_node+0x106/0x260
[<ea65e13b>] __kmalloc+0x54/0x160
[<c3858cd2>] msr_build_context.constprop.0+0x35/0x100
[<46635aff>] pm_check_save_msr+0x63/0x80
[<6b6bb938>] do_one_initcall+0x41/0x1f0
[<3f3add60>] kernel_init_freeable+0x199/0x1e8
[<3b538fde>] kernel_init+0x1a/0x110
[<938ae2b2>] ret_from_fork+0x1c/0x28
Which is a false positive.
Reproducer:
- Run rsync of whole kernel tree (multiple times if needed).
- start a kmemleak scan
- Note this is just an example: a lot of our internal tests hit these.
The root cause is similar to the fix in:
b0b592cf0836 x86/pm: Fix false positive kmemleak report in msr_build_context()
ie. the alignment within the packed struct saved_context
which has everything unaligned as there is only "u16 gs;" at start of
struct where in the past there were four u16 there thus aligning
everything afterwards. The issue is with the fact that Kmemleak only
searches for pointers that are aligned (see how pointers are scanned in
kmemleak.c) so when the struct members are not aligned it doesn't see
them.
Testing:
We run a lot of tests with our CI, and after applying this fix we do not
see any kmemleak issues any more whilst without it we see hundreds of
the above report. From a single, simple test run consisting of 416 individual test
cases on kernel 5.10 x86 with kmemleak enabled we got 20 failures due to this,
which is quite a lot. With this fix applied we get zero kmemleak related failures.
[Why]
When mode switching is triggered there is momentary noise visible on
some HDMI TV or displays.
[How]
Wait for 2 frames to make sure we have enough time to send out AV mute
and sink receives a full frame.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Acked-by: Wayne Lin <wayne.lin@amd.com> Signed-off-by: Leo Ma <hanghong.ma@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[How]
Check wheather state is NULL before releasing it.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Charlene Liu <charlene.liu@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Allen Pan <allen.pan@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
Odm update is doubled buffered. We need to wait for ODM update to be
completed before optimizing bandwidth or programming new udpates.
[HOW]
implement wait_for_odm_update_pending_complete function to wait for:
1. odm configuration update is no longer pending in timing generator.
2. no pending dpg pattern update for each active OPP.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
On DCN32 we support dynamic ODM even when OTG is blanked. When ODM
configuration is dynamically changed and the OTG is on blank pattern,
we will need to reprogram OPP's test pattern based on new ODM
configuration. Therefore we need to lock the OTG pipe to avoid temporary
corruption when we are reprogramming OPP blank patterns.
[HOW]
Add a new interdependent update lock implementation to lock all enabled
OTG pipes even when there is no plane on the OTG for DCN32.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
We still had an instance of get_idle_state checking the PMFW scratch
register instead of the actual idle allow signal.
[HOW]
Replace it with the SW state check for whether we had allowed idle
through notify_idle.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Duncan Ma <duncan.ma@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
When committing an update with ODM combine change when the plane is
removing or already removed, we fail to detect odm change in pipe
update flags. This has caused mismatch between new dc state and the
actual hardware state, because we missed odm programming.
[HOW]
- Detect odm change even for otg master pipe without a plane.
- Update odm config before calling program pipes for pipe with planes.
The commit also updates blank pattern programming when odm is changed
without plane. This is because number of OPP is changed when ODM
combine is changed. Blank pattern is per OPP so we will need to
reprogram OPP based on the new pipe topology.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Dillon Varone <dillon.varone@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
It's beneficial for ABM to know when new frame data are available.
[HOW]
Add new condition to allow dirty rects to be sent to DMUB when ABM is
active. ABM will use this as a signal that a new frame has arrived.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Anthony Koo <anthony.koo@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Josip Pavic <josip.pavic@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Otherwise after the GTT bo is released, the GTT and gart space is freed
but amdgpu_ttm_backend_unbind will not clear the gart page table entry
and leave valid mapping entry pointing to the stale system page. Then
if GPU access the gart address mistakely, it will read undefined value
instead page fault, harder to debug and reproduce the real issue.
Cc: stable@vger.kernel.org Signed-off-by: Philip Yang <Philip.Yang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY & HOW]
Currently, to map dc states into dml_display_cfg,
We create a dummy plane if the stream doesn't have any planes
attached to it. This dummy plane uses max addersable width height.
This results in certain mode validations failing when they shouldn't.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Swapnil Patel <swapnil.patel@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously, patches have been added to limit the reported count of SATA
ports for asm1064 and asm1166 SATA controllers, as those controllers do
report more ports than physically having.
While it is allowed to report more ports than physically having in CAP.NP,
it is not allowed to report more ports than physically having in the PI
(Ports Implemented) register, which is what these HBAs do.
(This is a AHCI spec violation.)
Unfortunately, it seems that the PMP implementation in these ASMedia HBAs
is also violating the AHCI and SATA-IO PMP specification.
What these HBAs do is that they do not report that they support PMP
(CAP.SPM (Supports Port Multiplier) is not set).
Instead, they have decided to add extra "virtual" ports in the PI register
that is used if a port multiplier is connected to any of the physical
ports of the HBA.
Enumerating the devices behind the PMP as specified in the AHCI and
SATA-IO specifications, by using PMP READ and PMP WRITE commands to the
physical ports of the HBA is not possible, you have to use the "virtual"
ports.
This is of course bad, because this gives us no way to detect the device
and vendor ID of the PMP actually connected to the HBA, which means that
we can not apply the proper PMP quirks for the PMP that is connected to
the HBA.
Limiting the port map will thus stop these controllers from working with
SATA Port Multipliers.
This patch reverts both patches for asm1064 and asm1166, so old behavior
is restored and SATA PMP will work again, but it will also reintroduce the
(minutes long) extra boot time for the ASMedia controllers that do not
have a PMP connected (either on the PCIe card itself, or an external PMP).
However, a longer boot time for some, is the lesser evil compared to some
other users not being able to detect their drives at all.
Fixes: 0077a504e1a4 ("ahci: asm1166: correct count of reported ports") Fixes: 9815e3961754 ("ahci: asm1064: correct count of reported ports") Cc: stable@vger.kernel.org Reported-by: Matt <cryptearth@googlemail.com> Signed-off-by: Conrad Kostecki <conikost@gentoo.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com>
[cassel: rewrote commit message] Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This option is needed to continue booting with QEMU. Recent changes that
made this optional meant that it gets unset in the test harness, and so
WireGuard CI has been broken. Fix this by simply setting this option.
Cc: stable@vger.kernel.org Fixes: 496ea826d1e1 ("RISC-V: provide Kconfig & commandline options to control parsing "riscv,isa"") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous commit fixed a bug that led to a NULL peer->device being
dereferenced. It's actually easier and faster performance-wise to
instead get the device from ctx->wg. This semantically makes more sense
too, since ctx->wg->peer_allowedips.seq is compared with
ctx->allowedips_seq, basing them both in ctx. This also acts as a
defence in depth provision against freed peers.
Cc: stable@vger.kernel.org Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If all peers are removed via wg_peer_remove_all(), rather than setting
peer_list to empty, the peer is added to a temporary list with a head on
the stack of wg_peer_remove_all(). If a netlink dump is resumed and the
cursored peer is one that has been removed via wg_peer_remove_all(), it
will iterate from that peer and then attempt to dump freed peers.
Fix this by instead checking peer->is_dead, which was explictly created
for this purpose. Also move up the device_update_lock lockdep assertion,
since reading is_dead relies on that.
It can be reproduced by a small script like:
echo "Setting config..."
ip link add dev wg0 type wireguard
wg setconf wg0 /big-config
(
while true; do
echo "Showing config..."
wg showconf wg0 > /dev/null
done
) &
sleep 4
wg setconf wg0 <(printf "[Peer]\nPublicKey=$(wg genkey)\n")
Resulting in:
BUG: KASAN: slab-use-after-free in __lock_acquire+0x182a/0x1b20
Read of size 8 at addr ffff88811956ec70 by task wg/59
CPU: 2 PID: 59 Comm: wg Not tainted 6.8.0-rc2-debug+ #5
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x70
print_address_description.constprop.0+0x2c/0x380
print_report+0xab/0x250
kasan_report+0xba/0xf0
__lock_acquire+0x182a/0x1b20
lock_acquire+0x191/0x4b0
down_read+0x80/0x440
get_peer+0x140/0xcb0
wg_get_device_dump+0x471/0x1130
Cc: stable@vger.kernel.org Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Reported-by: Lillian Berry <lillian@star-ark.net> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The LoongArch CRC32 hw acceleration is based on arch/mips/crypto/
crc32-mips.c. While the MIPS code supports both MIPS32 and MIPS64,
but LoongArch32 lacks the CRC instruction. As a result, the line
"len -= sizeof(u32)" is unnecessary.
Removing it can make context code style more unified and improve
code readability.
Commit fb24ea52f78e0d595852e ("drivers: Remove explicit invocations of
mmiowb()") remove all mmiowb() in drivers, but it says:
"NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation."
The mmio in radeon_ring_commit() is protected by a mutex rather than a
spinlock, but in the mutex fastpath it behaves similar to spinlock. We
can add mmiowb() calls in the radeon driver but the maintainer says he
doesn't like such a workaround, and radeon is not the only example of
mutex protected mmio.
So we should extend the mmiowb tracking system from spinlock to mutex,
and maybe other locking primitives. This is not easy and error prone, so
we solve it in the architectural code, by simply defining the __io_aw()
hook as mmiowb(). And we no longer need to override queued_spin_unlock()
so use the generic definition.
Without this, we get such an error when run 'glxgears' on weak ordering
architectures such as LoongArch:
radeon 0000:04:00.0: ring 0 stalled for more than 10324msec
radeon 0000:04:00.0: ring 3 stalled for more than 10240msec
radeon 0000:04:00.0: GPU lockup (current fence id 0x000000000001f412 last fence id 0x000000000001f414 on ring 3)
radeon 0000:04:00.0: GPU lockup (current fence id 0x000000000000f940 last fence id 0x000000000000f941 on ring 0)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
From GCC commit 3f13154553f8546a ("df-scan: remove ad-hoc handling of
global regs in asms"), global registers will no longer be forced to add
to the def-use chain. Then current_thread_info(), current_stack_pointer
and __my_cpu_offset may be lifted out of the loop because they are no
longer treated as "volatile variables".
This optimization is still correct for the current_thread_info() and
current_stack_pointer usages because they are associated to a thread.
However it is wrong for __my_cpu_offset because it is associated to a
CPU rather than a thread: if the thread migrates to a different CPU in
the loop, __my_cpu_offset should be changed.
Change __my_cpu_offset definition to treat it as a "volatile variable",
in order to avoid such a mis-optimization.
Cc: stable@vger.kernel.org Reported-by: Xiaotian Wu <wuxiaotian@loongson.cn> Reported-by: Miao Wang <shankerwangmiao@gmail.com> Signed-off-by: Xing Li <lixing@loongson.cn> Signed-off-by: Hongchen Zhang <zhanghongchen@loongson.cn> Signed-off-by: Rui Wang <wangrui@loongson.cn> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, we don't reenable the config if freezing the device failed.
For example, virtio-mem currently doesn't support suspend+resume, and
trying to freeze the device will always fail. Afterwards, the device
will no longer respond to resize requests, because it won't get notified
about config changes.
Let's fix this by re-enabling the config if freezing fails.
Fixes: 22b7050a024d ("virtio: defer config changed notifications") Cc: <stable@kernel.org> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Jason Wang <jasowang@redhat.com> Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240213135425.795001-1-david@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I found potencial out-of-bounds when buffer offset fields of a few requests
is invalid. This patch set the minimum value of buffer offset field to
->Buffer offset to validate buffer length.
Cc: stable@vger.kernel.org Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TP_STRUCT__entry that gets assigned the region name, or an
empty string if no region is present, is erroneously initialized
to the cxl_region pointer. It needs to be properly initialized
otherwise it's length is wrong and garbage chars can appear in
the kernel trace output: /sys/kernel/tracing/trace
The bad initialization was due in part to a naming conflict with
the parameter: struct cxl_region *region. The field 'region' is
already exposed externally as the region name, so changing that
to something logical, like 'region_name' is not an option. Instead
rename the internal only struct cxl_region to the commonly used
'cxlr'.
Impact is that tooling depending on that trace data can miss
picking up a valid event when searching by region name. The
TP_printk() output, if enabled, does emit the correct region
names in the dmesg log.
This was found during testing of the cxl-list option to report
media-errors for a region.
Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Jonathan Cameron <jonathan.cameron@huawei.com> Cc: Dave Jiang <dave.jiang@intel.com> Cc: Vishal Verma <vishal.l.verma@intel.com> Cc: stable@vger.kernel.org Fixes: ddf49d57b841 ("cxl/trace: Add TRACE support for CXL media-error records") Signed-off-by: Alison Schofield <alison.schofield@intel.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The __string() and __assign_str() helper macros of the TRACE_EVENT() macro
are going through some optimizations where only the source string of
__string() will be used and the __assign_str() source will be ignored and
later removed.
To make sure that there's no issues, a new check is added between the
__string() src argument and the __assign_str() src argument that does a
strcmp() to make sure they are the same string.
I'm working on improving the __assign_str() and __string() macros to be
more efficient, and removed some unneeded semicolons. This triggered a bug
in the build as some of the __assign_str() macros in intel_display_trace
was missing a terminating semicolon.
Link: https://lore.kernel.org/linux-trace-kernel/20240222133057.2af72a19@gandalf.local.home Cc: Daniel Vetter <daniel@ffwll.ch> Cc: David Airlie <airlied@gmail.com> Cc: stable@vger.kernel.org Fixes: 2ceea5d88048b ("drm/i915: Print plane name in fbc tracepoints") Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
I'm working on restructuring the __string* macros so that it doesn't need
to recalculate the string twice. That is, it will save it off when
processing __string() and the __assign_str() will not need to do the work
again as it currently does.
Currently __string_len(item, src, len) doesn't actually use "src", but my
changes will require src to be correct as that is where the __assign_str()
will get its value from.
The event class nfsd_clid_class has:
__string_len(name, name, clp->cl_name.len)
But the second "name" does not exist and causes my changes to fail to
build. That second parameter should be: clp->cl_name.data.
Link: https://lore.kernel.org/linux-trace-kernel/20240222122828.3d8d213c@gandalf.local.home Cc: Neil Brown <neilb@suse.de> Cc: Olga Kornievskaia <kolga@netapp.com> Cc: Dai Ngo <Dai.Ngo@oracle.com> Cc: Tom Talpey <tom@talpey.com> Cc: stable@vger.kernel.org Fixes: d27b74a8675ca ("NFSD: Use new __string_len C macros for nfsd_clid_class") Acked-by: Chuck Lever <chuck.lever@oracle.com> Acked-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the skb is reorganized during esp_output (!esp->inline), the pages
coming from the original skb fragments are supposed to be released back
to the system through put_page. But if the skb fragment pages are
originating from a page_pool, calling put_page on them will trigger a
page_pool leak which will eventually result in a crash.
This leak can be easily observed when using CONFIG_DEBUG_VM and doing
ipsec + gre (non offloaded) forwarding:
If ->NameOffset of smb2_create_req is smaller than Buffer offset of
smb2_create_req, slab-out-of-bounds read can happen from smb2_open.
This patch set the minimum value of the name offset to the buffer offset
to validate name length of smb2_create_req().
Cc: stable@vger.kernel.org Reported-by: Xuanzhe Yu <yuxuanzhe@outlook.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We know the request is either being removed, or already in the process of
being removed through task_work, so we can delete it from our waitid list
upfront. This is important for remove all conditions, as we otherwise
will find it multiple times and prevent cancelation progress.
Remove the dead check in cancelation as well for the hash_node being
empty or not. We already have a waitid reference check for ownership,
so we don't need to check the list too.
We know the request is either being removed, or already in the process of
being removed through task_work, so we can delete it from our futex list
upfront. This is important for remove all conditions, as we otherwise
will find it multiple times and prevent cancelation progress.
Cc: stable@vger.kernel.org Fixes: 194bb58c6090 ("io_uring: add support for futex wake and wait") Fixes: 8f350194d5cf ("io_uring: add support for vectored futex waits") Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 0499a78369ad ("ARM64: Dynamically allocate cpumasks and increase
supported CPUs to 512") changed the handling of cpumasks on ARM 64bit,
what resulted in the strange issues and warnings during cpufreq-dt
initialization on some big.LITTLE platforms.
This was caused by mixing OPPs between big and LITTLE cores, because
OPP-sharing information between big and LITTLE cores is computed on
cpumask, which in turn was not zeroed on allocation. Fix this by
switching to zalloc_cpumask_var() call.
As a matter of fact, continuous reads require additional handling at the
operation level in order for them to work properly. The core helpers do
have this additional logic now, but any time a controller implements its
own page helper, this extra logic is "lost". This means we need another
level of per-controller driver checks to ensure they can leverage
continuous reads. This is for now unsupported, so in order to ensure
continuous reads are enabled only when fully using the core page
helpers, we need to add more initial checks.
Also, as performance is not relevant during raw accesses, we also
prevent these from enabling the feature.
This should solve the issue seen with controllers such as the STM32 FMC2
when in sequencer mode. In this case, the continuous read feature would
be enabled but not leveraged, and most importantly not disabled, leading
to further operations to fail.
While crossing a LUN boundary, it is probably safer (and clearer) to
keep all members of the continuous read structure aligned, including the
pause page (which is the last page of the lun or the last page of the
continuous read). Once these members properly in sync, we can use the
rawnand_cap_cont_reads() helper everywhere to "prepare" the next
continuous read if there is one.
For LUN crossing boundaries, it is handy to know what is the index of
the last page in a LUN. This helper will soon be reused. At the same
time I rename page_per_lun to ppl in the calling function to clarify the
lines.
We need to avoid the first page if we don't read it entirely.
We need to avoid the last page if we don't read it entirely.
While rather simple, this logic has been failed in the previous
fix. This time I wrote about 30 unit tests locally to check each
possible condition, hopefully I covered them all.
Several users have reported this log getting dumped too regularly to
kernel log. The likely root cause has been identified, and it suggests
that this situation is expected for some configurations
(for example SMB2.1).
Since the function returns appropriately even for such cases, it is
fairly harmless to make this a debug log. When needed, the verbosity
can be increased to capture this log.
Cc: stable@vger.kernel.org Reported-by: Jan Čermák <sairon@sairon.cz> Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some code paths for querying server interfaces make a false
assumption that it will only get called for SMB3+. Since this
function now can get called from a generic code paths, the correct
thing to do is to have specific handler for this functionality
per SMB dialect, and call this handler.
This change adds such a handler and implements this handler only
for SMB 3.0 and 3.1.1.
Cc: stable@vger.kernel.org Cc: Jan Čermák <sairon@sairon.cz> Reported-by: Paulo Alcantara <pc@manguebit.com> Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a bug where nilfs_get_block() returns a successful status when
searching and inserting the specified block both fail inconsistently. If
this inconsistent behavior is not due to a previously fixed bug, then an
unexpected race is occurring, so return a temporary error -EAGAIN instead.
This prevents callers such as __block_write_begin_int() from requesting a
read into a buffer that is not mapped, which would cause the BUG_ON check
for the BH_Mapped flag in submit_bh_wbc() to fail.
Link: https://lkml.kernel.org/r/20240313105827.5296-3-konishi.ryusuke@gmail.com Fixes: 1f5abe7e7dbc ("nilfs2: replace BUG_ON and BUG calls triggerable from ioctl") Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "nilfs2: fix kernel bug at submit_bh_wbc()".
This resolves a kernel BUG reported by syzbot. Since there are two
flaws involved, I've made each one a separate patch.
The first patch alone resolves the syzbot-reported bug, but I think
both fixes should be sent to stable, so I've tagged them as such.
This patch (of 2):
Syzbot has reported a kernel bug in submit_bh_wbc() when writing file data
to a nilfs2 file system whose metadata is corrupted.
There are two flaws involved in this issue.
The first flaw is that when nilfs_get_block() locates a data block using
btree or direct mapping, if the disk address translation routine
nilfs_dat_translate() fails with internal code -ENOENT due to DAT metadata
corruption, it can be passed back to nilfs_get_block(). This causes
nilfs_get_block() to misidentify an existing block as non-existent,
causing both data block lookup and insertion to fail inconsistently.
The second flaw is that nilfs_get_block() returns a successful status in
this inconsistent state. This causes the caller __block_write_begin_int()
or others to request a read even though the buffer is not mapped,
resulting in a BUG_ON check for the BH_Mapped flag in submit_bh_wbc()
failing.
This fixes the first issue by changing the return value to code -EINVAL
when a conversion using DAT fails with code -ENOENT, avoiding the
conflicting condition that leads to the kernel bug described above. Here,
code -EINVAL indicates that metadata corruption was detected during the
block lookup, which will be properly handled as a file system error and
converted to -EIO when passing through the nilfs2 bmap layer.
In f2fs_do_write_data_page, FI_ATOMIC_FILE flag selects the target inode
between the original inode and COW inode. When aborting atomic write and
writeback occur simultaneously, invalid data can be written to original
inode if the FI_ATOMIC_FILE flag is cleared meanwhile.
To prevent the problem, let's truncate all pages before clearing the flag
Atomic write thread Writeback thread
f2fs_abort_atomic_write
clear_inode_flag(inode, FI_ATOMIC_FILE)
__writeback_single_inode
do_writepages
f2fs_do_write_data_page
- use dn of original inode
truncate_inode_pages_final
Fixes: 3db1de0e582c ("f2fs: change the current atomic write way") Cc: stable@vger.kernel.org #v5.19+ Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com> Reviewed-by: Yeongjin Gil <youngjin.gil@samsung.com> Signed-off-by: Sunmin Jeong <s_min.jeong@samsung.com> Reviewed-by: Daeho Jeong <daehojeong@google.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In f2fs_update_inode, i_size of the atomic file isn't updated until
FI_ATOMIC_COMMITTED flag is set. When committing atomic write right
after the writeback of the inode, i_size of the raw inode will not be
updated. It can cause the atomicity corruption due to a mismatch between
old file size and new data.
To prevent the problem, let's mark inode dirty for FI_ATOMIC_COMMITTED
Atomic write thread Writeback thread
__writeback_single_inode
write_inode
f2fs_update_inode
- skip i_size update
f2fs_ioc_commit_atomic_write
f2fs_commit_atomic_write
set_inode_flag(inode, FI_ATOMIC_COMMITTED)
f2fs_do_sync_file
f2fs_fsync_node_pages
- skip f2fs_update_inode since the inode is clean
Fixes: 3db1de0e582c ("f2fs: change the current atomic write way") Cc: stable@vger.kernel.org #v5.19+ Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com> Reviewed-by: Yeongjin Gil <youngjin.gil@samsung.com> Signed-off-by: Sunmin Jeong <s_min.jeong@samsung.com> Reviewed-by: Daeho Jeong <daehojeong@google.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Passing a NULL buffer into the lsm_get_self_attr() syscall is a valid
way to quickly determine the minimum size of the buffer needed to for
the syscall to return all of the LSM attributes to the caller.
Unfortunately we/I broke that behavior in commit d7cf3412a9f6
("lsm: consolidate buffer size handling into lsm_fill_user_ctx()")
such that it returned an error to the caller; this patch restores the
original desired behavior of using the NULL buffer as a quick way to
correctly size the attribute buffer.
Cc: stable@vger.kernel.org Fixes: d7cf3412a9f6 ("lsm: consolidate buffer size handling into lsm_fill_user_ctx()") Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change the size parameters in lsm_list_modules(), lsm_set_self_attr()
and lsm_get_self_attr() from size_t to u32. This avoids the need to
have different interfaces for 32 and 64 bit systems.
Cc: stable@vger.kernel.org Fixes: a04a1198088a ("LSM: syscalls for current process attributes") Fixes: ad4aff9ec25f ("LSM: Create lsm_list_modules system call") Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Reported-and-reviewed-by: Dmitry V. Levin <ldv@strace.io>
[PM: subject and metadata tweaks, syscall.h fixes] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code "max(1U, 3 * (1U << shift) / 4)" comes from the Kyber I/O
scheduler. The Kyber I/O scheduler maintains one internal queue per hwq
and hence derives its async_depth from the number of hwq tags. Using
this approach for the mq-deadline scheduler is wrong since the
mq-deadline scheduler maintains one internal queue for all hwqs
combined. Hence this revert.
Cc: stable@vger.kernel.org Cc: Damien Le Moal <dlemoal@kernel.org> Cc: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Cc: Zhiguo Niu <Zhiguo.Niu@unisoc.com> Fixes: d47f9717e5cf ("block/mq-deadline: use correct way to throttling write requests") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20240313214218.1736147-1-bvanassche@acm.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the RISC-V specification, the stimecmp register doesn't have a default
value. To prevent the timer interrupt from being triggered during timer
initialization, clear the timer interrupt by writing stimecmp with a
maximum value.
Fixes: 9f7a8ff6391f ("RISC-V: Prefer sstc extension if available") Cc: <stable@vger.kernel.org> Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com> Reviewed-by: Samuel Holland <samuel.holland@sifive.com> Tested-by: Samuel Holland <samuel.holland@sifive.com> Reviewed-by: Atish Patra <atishp@rivosinc.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20240306172330.255844-1-leyfoon.tan@starfivetech.com Signed-off-by: Sasha Levin <sashal@kernel.org>
None of the callers of drm_panel_get_modes() expect it to return
negative error codes. Either they propagate the return value in their
struct drm_connector_helper_funcs .get_modes() hook (which is also not
supposed to return negative codes), or add it to other counts leading to
bogus values.
On the other hand, many of the struct drm_panel_funcs .get_modes() hooks
do return negative error codes, so handle them gracefully instead of
propagating further.
Return 0 for no modes, whatever the reason.
Cc: Neil Armstrong <neil.armstrong@linaro.org> Cc: Jessica Zhang <quic_jesszhan@quicinc.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: stable@vger.kernel.org Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/79f559b72d8c493940417304e222a4b04dfa19c4.1709913674.git.jani.nikula@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The .get_modes() callback is supposed to return the number of modes,
never a negative error code. If a negative value is returned, it'll just
be interpreted as a negative count, and added to previous calculations.
Document the rules, but handle the negative values gracefully with an
error message.
projects / thirdparty / kernel / stable.git / log
