As explained by Horatiu Vultur in commit 603ead96582d ("net: sparx5: Add
spinlock for frame transmission from CPU") which is for a similar
hardware design, multiple CPUs can simultaneously perform injection
or extraction. There are only 2 register groups for injection and 2
for extraction, and the driver only uses one of each. So we'd better
serialize access using spin locks, otherwise frame corruption is
possible.
Note that unlike in sparx5, FDMA in ocelot does not have this issue
because struct ocelot_fdma_tx_ring already contains an xmit_lock.
I guess this is mostly a problem for NXP LS1028A, as that is dual core.
I don't think VSC7514 is. So I'm blaming the commit where LS1028A (aka
the felix DSA driver) started using register-based packet injection and
extraction.
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are 2 distinct code paths (listed below) in the source code which
set up an injection header for Ocelot(-like) switches. Code path (2)
lacks the QoS class and source port being set correctly. Especially the
improper QoS classification is a problem for the "ocelot-8021q"
alternative DSA tagging protocol, because we support tc-taprio and each
packet needs to be scheduled precisely through its time slot. This
includes PTP, which is normally assigned to a traffic class other than
0, but would be sent through TC 0 nonetheless.
The code paths are:
(1) ocelot_xmit_common() from net/dsa/tag_ocelot.c - called only by the
standard "ocelot" DSA tagging protocol which uses NPI-based
injection - sets up bit fields in the tag manually to account for
a small difference (destination port offset) between Ocelot and
Seville. Namely, ocelot_ifh_set_dest() is omitted out of
ocelot_xmit_common(), because there's also seville_ifh_set_dest().
(2) ocelot_ifh_set_basic(), called by:
- ocelot_fdma_prepare_skb() for FDMA transmission of the ocelot
switchdev driver
- ocelot_port_xmit() -> ocelot_port_inject_frame() for
register-based transmission of the ocelot switchdev driver
- felix_port_deferred_xmit() -> ocelot_port_inject_frame() for the
DSA tagger ocelot-8021q when it must transmit PTP frames (also
through register-based injection).
sets the bit fields according to its own logic.
The problem is that (2) doesn't call ocelot_ifh_set_qos_class().
Copying that logic from ocelot_xmit_common() fixes that.
Unfortunately, although desirable, it is not easily possible to
de-duplicate code paths (1) and (2), and make net/dsa/tag_ocelot.c
directly call ocelot_ifh_set_basic()), because of the ocelot/seville
difference. This is the "minimal" fix with some logic duplicated (but
at least more consolidated).
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On an NXP LS1028A (felix DSA driver) with the following configuration:
- ocelot-8021q tagging protocol
- VLAN-aware bridge (with STP) spanning at least swp0 and swp1
- 8021q VLAN upper interfaces on swp0 and swp1: swp0.700, swp1.700
- ptp4l on swp0.700 and swp1.700
we see that the ptp4l instances do not see each other's traffic,
and they all go to the grand master state due to the
ANNOUNCE_RECEIPT_TIMEOUT_EXPIRES condition.
Jumping to the conclusion for the impatient
-------------------------------------------
There is a zero-day bug in the ocelot switchdev driver in the way it
handles VLAN-tagged packet injection. The correct logic already exists in
the source code, in function ocelot_xmit_get_vlan_info() added by commit 5ca721c54d86 ("net: dsa: tag_ocelot: set the classified VLAN during xmit").
But it is used only for normal NPI-based injection with the DSA "ocelot"
tagging protocol. The other injection code paths (register-based and
FDMA-based) roll their own wrong logic. This affects and was noticed on
the DSA "ocelot-8021q" protocol because it uses register-based injection.
By moving ocelot_xmit_get_vlan_info() to a place that's common for both
the DSA tagger and the ocelot switch library, it can also be called from
ocelot_port_inject_frame() in ocelot.c.
We need to touch the lines with ocelot_ifh_port_set()'s prototype
anyway, so let's rename it to something clearer regarding what it does,
and add a kernel-doc. ocelot_ifh_set_basic() should do.
Investigation notes
-------------------
Debugging reveals that PTP event (aka those carrying timestamps, like
Sync) frames injected into swp0.700 (but also swp1.700) hit the wire
with two VLAN tags:
The second (unexpected) VLAN tag makes felix_check_xtr_pkt() ->
ptp_classify_raw() fail to see these as PTP packets at the link
partner's receiving end, and return PTP_CLASS_NONE (because the BPF
classifier is not written to expect 2 VLAN tags).
The reason why packets have 2 VLAN tags is because the transmission
code treats VLAN incorrectly.
Neither ocelot switchdev, nor felix DSA, declare the NETIF_F_HW_VLAN_CTAG_TX
feature. Therefore, at xmit time, all VLANs should be in the skb head,
and none should be in the hwaccel area. This is done by:
which does _not_ zero out skb->vlan_tci as seen by skb_vlan_tag_get().
This means that ocelot, when it calls skb_vlan_tag_get(), sees
(and uses) a residual skb->vlan_tci, while the same VLAN tag is
_already_ in the skb head.
The trivial fix for double VLAN headers is to replace the content of
ocelot_ifh_port_set() with:
if (skb_vlan_tag_present(skb))
ocelot_ifh_set_vlan_tci(ifh, skb_vlan_tag_get(skb));
but this would not be correct either, because, as mentioned,
vlan_hw_offload_capable() is false for us, so we'd be inserting dead
code and we'd always transmit packets with VID=0 in the injection frame
header.
I can't actually test the ocelot switchdev driver and rely exclusively
on code inspection, but I don't think traffic from 8021q uppers has ever
been injected properly, and not double-tagged. Thus I'm blaming the
introduction of VLAN fields in the injection header - early driver code.
As hinted at in the early conclusion, what we _want_ to happen for
VLAN transmission was already described once in commit 5ca721c54d86
("net: dsa: tag_ocelot: set the classified VLAN during xmit").
ocelot_xmit_get_vlan_info() intends to ensure that if the port through
which we're transmitting is under a VLAN-aware bridge, the outer VLAN
tag from the skb head is stripped from there and inserted into the
injection frame header (so that the packet is processed in hardware
through that actual VLAN). And in all other cases, the packet is sent
with VID=0 in the injection frame header, since the port is VLAN-unaware
and has logic to strip this VID on egress (making it invisible to the
wire).
Fixes: 08d02364b12f ("net: mscc: fix the injection header") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function hci_sched_le needs to update the respective counter variable
inplace other the likes of hci_quote_sent would attempt to use the
possible outdated value of conn->{le_cnt,acl_cnt}.
Link: https://github.com/bluez/bluez/issues/915 Fixes: 73d80deb7bdf ("Bluetooth: prioritizing data over HCI") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This inverts the LE State quirk so by default we assume the controllers
would report valid states rather than invalid which is how quirks
normally behave, also this would result in HCI command failing it the LE
States are really broken thus exposing the controllers that are really
broken in this respect.
Link: https://github.com/bluez/bluez/issues/584 Fixes: 220915857e29 ("Bluetooth: Adding driver and quirk defs for multi-role LE") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When trying to build compile_commands.json for an external module against
the kernel built in a separate output directory, the following error is
displayed:
make[1]: *** No rule to make target 'scripts/clang-tools/gen_compile_commands.py',
needed by 'compile_commands.json'. Stop.
This is because gen_compile_commands.py was previously looked up using a
relative path to $(srctree), but commit b1992c3772e6 ("kbuild: use
$(src) instead of $(srctree)/$(src) for source directory") stopped
defining VPATH for external module builds.
Prefixing gen_compile_commands.py with $(srctree) fixes the problem.
Fixes: b1992c3772e6 ("kbuild: use $(src) instead of $(srctree)/$(src) for source directory") Signed-off-by: Alexandre Courbot <gnurou@gmail.com> Reviewed-by: Nicolas Schier <nicolas@fjasle.eu> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The data conversion is done rather by a wrong function. We convert to
BE32, not from BE32. Although the end result must be same, this was
complained by the compiler.
Fix the code again and align with another similar function
tas2563_apply_calib() that does already right.
There is a small window in ssam_serial_hub_probe() where the controller
is initialized but has not been started yet. Specifically, between
ssam_controller_init() and ssam_controller_start(). Any failure in this
window, for example caused by a failure of serdev_device_open(),
currently results in an incorrect warning being emitted.
In particular, any failure in this window results in the controller
being destroyed via ssam_controller_destroy(). This function checks the
state of the controller and, in an attempt to validate that the
controller has been cleanly shut down before we try and deallocate any
resources, emits a warning if that state is not SSAM_CONTROLLER_STOPPED.
However, since we have only just initialized the controller and have not
yet started it, its state is SSAM_CONTROLLER_INITIALIZED. Note that this
is the only point at which the controller has this state, as it will
change after we start the controller with ssam_controller_start() and
never revert back. Further, at this point no communication has taken
place and the sender and receiver threads have not been started yet (and
we may not even have an open serdev device either).
Therefore, it is perfectly safe to call ssam_controller_destroy() with a
state of SSAM_CONTROLLER_INITIALIZED. This, however, means that the
warning currently being emitted is incorrect. Fix it by extending the
check.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem") Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20240811124645.246016-1-luzmaximilian@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In transmit path, it is likely that the iova is not aligned to PCIe TLP
max payload size, which is 128 for WCN7850. Normally in such cases hardware
is expected to split the packet into several parts in a manner such that
they, other than the first one, have aligned iova. However due to hardware
limitations, WCN7850 does not behave like that properly with some specific
unaligned iova in transmit path. This easily results in target hang in a
KPI transmit test: packet send/receive failure, WMI command send timeout
etc. Also fatal error seen in PCIe level:
Work around this by manually moving/reallocating payload buffer such that
we can map it to a 128 bytes aligned iova. The moving requires sufficient
head room or tail room in skb: for the former we can do ourselves a favor
by asking some extra bytes when registering with mac80211, while for the
latter we can do nothing.
Moving/reallocating buffer consumes additional CPU cycles, but the good news
is that an aligned iova increases PCIe efficiency. In my tests on some X86
platforms the KPI results are almost consistent.
Since this is seen only with WCN7850, add a new hardware parameter to
differentiate from others.
This commit changes device mapper, so that it returns -ERESTARTSYS
instead of -EINTR when it is interrupted by a signal (so that the ioctl
can be restarted).
The manpage signal(7) says that the ioctl function should be restarted if
the signal was handled with SA_RESTART.
Clang static checker (scan-build) warning:
cifsglob.h:line 890, column 3
Access to field 'ops' results in a dereference of a null pointer.
Commit 519be989717c ("cifs: Add a tracepoint to track credits involved in
R/W requests") adds a check for 'rdata->server', and let clang throw this
warning about NULL dereference.
When 'rdata->credits.value != 0 && rdata->server == NULL' happens,
add_credits_and_wake_if() will call rdata->server->ops->add_credits().
This will cause NULL dereference problem. Add a check for 'rdata->server'
to avoid NULL dereference.
Cc: stable@vger.kernel.org Fixes: 69c3c023af25 ("cifs: Implement netfslib hooks") Reviewed-by: David Howells <dhowells@redhat.com> Signed-off-by: Su Hui <suhui@nfschina.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a tracepoint to track the credit changes and server in_flight value
involved in the lifetime of a R/W request, logging it against the
request/subreq debugging ID. This requires the debugging IDs to be
recorded in the cifs_credits struct.
Also add a three-state flag to struct cifs_credits to note if we're
interested in determining when the in_flight contribution ends and, if so,
to track whether we've decremented the contribution yet.
Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 74c2ab6d653b ("smb/client: avoid possible NULL dereference in cifs_free_subrequest()") Signed-off-by: Sasha Levin <sashal@kernel.org>
After running once, the for_each_trip_desc() loop in
bang_bang_manage() is pure needless overhead because it is not going to
make any changes unless a new cooling device has been bound to one of
the trips in the thermal zone or the system is resuming from sleep.
For this reason, make bang_bang_manage() set governor_data for the
thermal zone and check it upfront to decide whether or not it needs to
do anything.
However, governor_data needs to be reset in some cases to let
bang_bang_manage() know that it should walk the trips again, so add an
.update_tz() callback to the governor and make the core additionally
invoke it during system resume.
To avoid affecting the other users of that callback unnecessarily, add
a special notification reason for system resume, THERMAL_TZ_RESUME, and
also pass it to __thermal_zone_device_update() called during system
resume for consistency.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Kästle <peter@piie.net> Reviewed-by: Zhang Rui <rui.zhang@intel.com> Cc: 6.10+ <stable@vger.kernel.org> # 6.10+ Link: https://patch.msgid.link/2285575.iZASKD2KPV@rjwysocki.net Signed-off-by: Sasha Levin <sashal@kernel.org>
After recent changes, the Bang-bang governor may not adjust the
initial configuration of cooling devices to the actual situation.
Namely, if a cooling device bound to a certain trip point starts in
the "on" state and the thermal zone temperature is below the threshold
of that trip point, the trip point may never be crossed on the way up
in which case the state of the cooling device will never be adjusted
because the thermal core will never invoke the governor's
.trip_crossed() callback. [Note that there is no issue if the zone
temperature is at the trip threshold or above it to start with because
.trip_crossed() will be invoked then to indicate the start of thermal
mitigation for the given trip.]
To address this, add a .manage() callback to the Bang-bang governor
and use it to ensure that all of the thermal instances managed by the
governor have been initialized properly and the states of all of the
cooling devices involved have been adjusted to the current zone
temperature as appropriate.
Move the setting of the thermal instance target state from
bang_bang_control() into a separate function that will be also called
in a different place going forward.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Kästle <peter@piie.net> Reviewed-by: Zhang Rui <rui.zhang@intel.com> Cc: 6.10+ <stable@vger.kernel.org> # 6.10+ Link: https://patch.msgid.link/3313587.aeNJFYEL58@rjwysocki.net Signed-off-by: Sasha Levin <sashal@kernel.org>
Some cooling device target state checks in bang_bang_control()
done before setting the new target state are not necessary after
recent changes, so drop them.
Also avoid updating the target state before checking it for
unexpected values.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 84248e35d9b6 ("thermal: gov_bang_bang: Split bang_bang_control()") Signed-off-by: Sasha Levin <sashal@kernel.org>
OLED panels don't support the ABM, they shouldn't offer the
panel_power_savings attribute to the user. Check whether aux BL
control support was enabled to decide whether to offer it.
Reported-by: Gergo Koteles <soyer@irl.hu> Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3359 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Tested-by: Gergo Koteles <soyer@irl.hu> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When interrupt is turned on while a lock holding by spin_lock_irq it
throws a warning because of potential deadlock.
blk_mq_prep_dispatch_rq
blk_mq_get_driver_tag
__blk_mq_get_driver_tag
__blk_mq_alloc_driver_tag
blk_mq_tag_busy -> tag is already busy
// failed to get driver tag
blk_mq_mark_tag_wait
spin_lock_irq(&wq->lock) -> lock A (&sbq->ws[i].wait)
__add_wait_queue(wq, wait) -> wait queue active
blk_mq_get_driver_tag
__blk_mq_tag_busy
-> 1) tag must be idle, which means there can't be inflight IO
spin_lock_irq(&tags->lock) -> lock B (hctx->tags)
spin_unlock_irq(&tags->lock) -> unlock B, turn on interrupt accidentally
-> 2) context must be preempt by IO interrupt to trigger deadlock.
As shown above, the deadlock is not possible in theory, but the warning
still need to be fixed.
Fix it by using spin_lock_irqsave to get lockB instead of spin_lock_irq.
Fixes: 4f1731df60f9 ("blk-mq: fix potential io hang by wrong 'wake_batch'") Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Yu Kuai <yukuai3@huawei.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20240815024736.2040971-1-lilingfeng@huaweicloud.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, kasan_init_sw_tags() is called before setup_per_cpu_areas(),
so per_cpu(prng_state, cpu) accesses the same address regardless of the
value of "cpu", and the same seed value gets copied to the percpu area
for every CPU. Fix this by moving the call to smp_prepare_boot_cpu(),
which is the first architecture hook after setup_per_cpu_areas().
Fixes: 3c9e3aa11094 ("kasan: add tag related helper functions") Fixes: 3f41b6093823 ("kasan: fix random seed generation for tag-based mode") Signed-off-by: Samuel Holland <samuel.holland@sifive.com> Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com> Link: https://lore.kernel.org/r/20240814091005.969756-1-samuel.holland@sifive.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 779dbc2e78d7 ("printk: Avoid non-panic CPUs writing
to ringbuffer") disabled non-panic CPUs to further write messages to
ringbuffer after panicked.
Since the commit, non-panicked CPU's are not allowed to write to
ring buffer after panicked and CPU backtrace which is triggered
after panicked to sample non-panicked CPUs' backtrace no longer
serves its function as it has nothing to print.
Fix the issue by allowing non-panicked CPUs to write into ringbuffer
while CPU backtrace is in flight.
Fixes: 779dbc2e78d7 ("printk: Avoid non-panic CPUs writing to ringbuffer") Signed-off-by: Ryo Takakura <takakura@valinux.co.jp> Reviewed-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20240812072703.339690-1-takakura@valinux.co.jp Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
topology_is_core_online() checks if the core a CPU belongs to
is online. The core is online if at least one of the sibling
CPUs is online. The first CPU of an online core is also online
in the common case, so this should be fairly quick.
If a core is offline then enabling SMT should not online CPUs of
this core. By enabling SMT, what is intended is either changing the SMT
value from "off" to "on" or setting the SMT level (threads per core) from a
lower to higher value.
On PowerPC the ppc64_cpu utility can be used, among other things, to
perform the following functions:
ppc64_cpu --cores-on # Get the number of online cores
ppc64_cpu --cores-on=X # Put exactly X cores online
ppc64_cpu --offline-cores=X[,Y,...] # Put specified cores offline
ppc64_cpu --smt={on|off|value} # Enable, disable or change SMT level
If the user has decided to offline certain cores, enabling SMT should
not online CPUs in those cores. This patch fixes the issue and changes
the behaviour as described, by introducing an arch specific function
topology_is_core_online(). It is currently implemented only for PowerPC.
It's more natural to use ktime/ns instead of keeping around usec,
especially since we're comparing it against user provided timers,
so convert napi busy poll internal handling to ktime. It's also nicer
since the type (ktime_t vs unsigned long) now tells the unit of measure.
Keep everything as ktime, which we convert to/from micro seconds for
IORING_[UN]REGISTER_NAPI. The net/ busy polling works seems to work with
usec, however it's not real usec as shift by 10 is used to get it from
nsecs, see busy_loop_current_time(), so it's easy to get truncated nsec
back and we get back better precision.
Note, we can further improve it later by removing the truncation and
maybe convincing net/ to use ktime/ns instead.
Since the do_div() macro casts the divisor to u32 anyway, remove the
unnecessary s64 cast and fix the following Coccinelle/coccicheck
warning reported by do_div.cocci:
WARNING: do_div() does a 64-by-32 division, please consider using div64_s64 instead
This reverts commit bc792884b76f ("s390/dasd: Establish DMA alignment").
Quoting the original commit:
linux-next commit bf8d08532bc1 ("iomap: add support for dma aligned
direct-io") changes the alignment requirement to come from the block
device rather than the block size, and the default alignment
requirement is 512-byte boundaries. Since DASD I/O has page
alignments for IDAW/TIDAW requests, let's override this value to
restore the expected behavior.
I mentioned TIDAW, but that was wrong. TIDAWs have no distinct alignment
requirement (per p. 15-70 of POPS SA22-7832-13):
Unless otherwise specified, TIDAWs may designate
a block of main storage on any boundary and length
up to 4K bytes, provided the specified block does not
cross a 4 K-byte boundary.
IDAWs do, but the original commit neglected that while ECKD DASD are
typically formatted in 4096-byte blocks, they don't HAVE to be. Formatting
an ECKD volume with smaller blocks is permitted (dasdfmt -b xxx), and the
problematic commit enforces alignment properties to such a device that
will result in errors, such as:
The original commit omitted the FBA discipline for just this reason,
but the formatted block size of the other disciplines was overlooked.
The solution to all of this is to revert to the original behavior,
such that the block size can be respected. There were two commits [1]
that moved this code in the interim, so a straight git-revert is not
possible, but the change is straightforward.
But what of the original problem? That was manifested with a direct-io
QEMU guest, where QEMU itself was changed a month or two later with
commit 25474d90aa ("block: use the request length for iov alignment")
such that the blamed kernel commit is unnecessary.
[1] commit 0127a47f58c6 ("dasd: move queue setup to common code")
commit fde07a4d74e3 ("dasd: use the atomic queue limits API")
Fixes: bc792884b76f ("s390/dasd: Establish DMA alignment") Reviewed-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Eric Farman <farman@linux.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Link: https://lore.kernel.org/r/20240812125733.126431-2-sth@linux.ibm.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Another oddity in these config entries is their default value can fall
back to 'n', which is a value for bool or tristate symbols.
The '|| echo n' is an incorrect workaround to avoid the syntax error.
This is not a big deal, as the entry is hidden by 'depends on RUST' in
situations where '$(RUSTC) --version' or '$(BINDGEN) --version' fails.
Anyway, it looks odd.
The default of a string type symbol should be a double-quoted string
literal. Turn it into an empty string when the version command fails.
Fixes: 2f7ab1267dc9 ("Kbuild: add Rust support") Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Link: https://lore.kernel.org/r/20240727140302.1806011-2-masahiroy@kernel.org
[ Rebased on top of v6.11-rc1. - Miguel ] Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When enabling UBSAN on Raspberry Pi 5, we get the following warning:
[ 387.894977] UBSAN: array-index-out-of-bounds in drivers/gpu/drm/v3d/v3d_sched.c:320:3
[ 387.903868] index 7 is out of range for type '__u32 [7]'
[ 387.909692] CPU: 0 PID: 1207 Comm: kworker/u16:2 Tainted: G WC 6.10.3-v8-16k-numa #151
[ 387.919166] Hardware name: Raspberry Pi 5 Model B Rev 1.0 (DT)
[ 387.925961] Workqueue: v3d_csd drm_sched_run_job_work [gpu_sched]
[ 387.932525] Call trace:
[ 387.935296] dump_backtrace+0x170/0x1b8
[ 387.939403] show_stack+0x20/0x38
[ 387.942907] dump_stack_lvl+0x90/0xd0
[ 387.946785] dump_stack+0x18/0x28
[ 387.950301] __ubsan_handle_out_of_bounds+0x98/0xd0
[ 387.955383] v3d_csd_job_run+0x3a8/0x438 [v3d]
[ 387.960707] drm_sched_run_job_work+0x520/0x6d0 [gpu_sched]
[ 387.966862] process_one_work+0x62c/0xb48
[ 387.971296] worker_thread+0x468/0x5b0
[ 387.975317] kthread+0x1c4/0x1e0
[ 387.978818] ret_from_fork+0x10/0x20
[ 387.983014] ---[ end trace ]---
This happens because the UAPI provides only seven configuration
registers and we are reading the eighth position of this u32 array.
Therefore, fix the out-of-bounds read in `v3d_csd_job_run()` by
accessing only seven positions on the '__u32 [7]' array. The eighth
register exists indeed on V3D 7.1, but it isn't currently used. That
being so, let's guarantee that it remains unused and add a note that it
could be set in a future patch.
Fix noise from speakers connected to AUX port when no sound is playing.
The problem occurs because the `alc_shutup_pins` function includes
a 0x10ec0257 vendor ID, which causes noise on Lenovo IdeaPad 3 15IAU7 with
Realtek ALC257 codec when no sound is playing.
Removing this vendor ID from the function fixes the bug.
Fixes: 70794b9563fe ("ALSA: hda/realtek: Add more codec ID to no shutup pins list") Signed-off-by: Parsa Poorshikhian <parsa.poorsh@gmail.com> Link: https://patch.msgid.link/20240810150939.330693-1-parsa.poorsh@gmail.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
During Linux graceful reboot, the GPIO interrupts are not disabled.
Since the drivers are not removed during graceful reboot,
the logic to call mlxbf3_gpio_irq_disable() is not triggered.
Interrupts that remain enabled can cause issues on subsequent boots.
For example, the mlxbf-gige driver contains PHY logic to bring up the link.
If the gpio-mlxbf3 driver loads first, the mlxbf-gige driver
will use a GPIO interrupt to bring up the link.
Otherwise, it will use polling.
The next time Linux boots and loads the drivers in this order, we encounter the issue:
- mlxbf-gige loads first and uses polling while the GPIO10
interrupt is still enabled from the previous boot. So if
the interrupt triggers, there is nothing to clear it.
- gpio-mlxbf3 loads.
- i2c-mlxbf loads. The interrupt doesn't trigger for I2C
because it is shared with the GPIO interrupt line which
was not cleared.
The solution is to add a shutdown function to the GPIO driver to clear and disable
all interrupts. Also clear the interrupt after disabling it in mlxbf3_gpio_irq_disable().
With CONFIG_LTO_CLANG=y, the compiler may add .llvm.<hash> suffix to
function names to avoid duplication. APIs like kallsyms_lookup_name()
and kallsyms_on_each_match_symbol() tries to match these symbol names
without the .llvm.<hash> suffix, e.g., match "c_stop" with symbol
c_stop.llvm.17132674095431275852. This turned out to be problematic
for use cases that require exact match, for example, livepatch.
Fix this by making the APIs to match symbols exactly.
Also cleanup kallsyms_selftests accordingly.
Signed-off-by: Song Liu <song@kernel.org> Fixes: 8cc32a9bbf29 ("kallsyms: strip LTO-only suffixes from promoted global functions") Tested-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Acked-by: Petr Mladek <pmladek@suse.com> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Luis Chamberlain <mcgrof@kernel.org> Link: https://lore.kernel.org/r/20240807220513.3100483-3-song@kernel.org Signed-off-by: Kees Cook <kees@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This reimplements commit 951bcae6c5a0 ("kallsyms: Avoid weak references
for kallsyms symbols") because I am not a big fan of PROVIDE().
As an alternative solution, this commit prepends one more kallsyms step.
KSYMS .tmp_vmlinux.kallsyms0.S # added
AS .tmp_vmlinux.kallsyms0.o # added
LD .tmp_vmlinux.btf
BTF .btf.vmlinux.bin.o
LD .tmp_vmlinux.kallsyms1
NM .tmp_vmlinux.kallsyms1.syms
KSYMS .tmp_vmlinux.kallsyms1.S
AS .tmp_vmlinux.kallsyms1.o
LD .tmp_vmlinux.kallsyms2
NM .tmp_vmlinux.kallsyms2.syms
KSYMS .tmp_vmlinux.kallsyms2.S
AS .tmp_vmlinux.kallsyms2.o
LD vmlinux
Step 0 takes /dev/null as input, and generates .tmp_vmlinux.kallsyms0.o,
which has a valid kallsyms format with the empty symbol list, and can be
linked to vmlinux. Since it is really small, the added compile-time cost
is negligible.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Acked-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Stable-dep-of: 020925ce9299 ("kallsyms: Do not cleanup .llvm.<hash> suffix before sorting symbols") Signed-off-by: Sasha Levin <sashal@kernel.org>
- Specify the extra objects directly in vmlinux_link()
- Move the AS rule to kallsyms()
- Set kallsymso and btf_vmlinux_bin_o where they are generated
- Remove unneeded variable, kallsymso_prev
- Introduce the btf_data variable
- Introduce the strip_debug flag instead of checking the output name
No functional change intended.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Stable-dep-of: 020925ce9299 ("kallsyms: Do not cleanup .llvm.<hash> suffix before sorting symbols") Signed-off-by: Sasha Levin <sashal@kernel.org>
When config TC during the reset process, may cause a deadlock, the flow is
as below:
pf reset start
│
▼
......
setup tc │
│ ▼
▼ DOWN: napi_disable()
napi_disable()(skip) │
│ │
▼ ▼
...... ......
│ │
▼ │
napi_enable() │
▼
UINIT: netif_napi_del()
│
▼
......
│
▼
INIT: netif_napi_add()
│
▼
...... global reset start
│ │
▼ ▼
UP: napi_enable()(skip) ......
│ │
▼ ▼
...... napi_disable()
In reset process, the driver will DOWN the port and then UINIT, in this
case, the setup tc process will UP the port before UINIT, so cause the
problem. Adds a DOWN process in UINIT to fix it.
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Consider the followed case that the user change speed and reset the net
interface. Before the hw change speed successfully, the driver get old
old speed from hw by timer task. After reset, the previous speed is config
to hw. As a result, the new speed is configed successfully but lost after
PF reset. The followed pictured shows more dirrectly.
Currently, if hns3 PF or VF FLR reset failed after five times retry,
the reset done process will directly release the semaphore
which has already released in hclge_reset_prepare_general.
This will cause down operation fail.
So this patch fixes it by adding reset state judgement. The up operation is
only called after successful PF FLR reset.
Fixes: 8627bdedc435 ("net: hns3: refactor the precedure of PF FLR") Fixes: f28368bb4542 ("net: hns3: refactor the procedure of VF FLR") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When deleting netns, it is possible to still have some tasks running,
e.g. background tasks like tcpdump running in the background, not
stopped because the test has been interrupted.
Before deleting the netns, it is then safer to kill all attached PIDs,
if any. That should reduce some noises after the end of some tests, and
help with the debugging of some issues. That's why this modification is
seen as a "fix".
After a vsock socket has been added to a BPF sockmap, its prot->recvmsg
has been replaced with vsock_bpf_recvmsg(). Thus the following
recursiion could happen:
vsock_bpf_recvmsg()
-> __vsock_recvmsg()
-> vsock_connectible_recvmsg()
-> prot->recvmsg()
-> vsock_bpf_recvmsg() again
We need to fix it by calling the original ->recvmsg() without any BPF
sockmap logic in __vsock_recvmsg().
Fixes: 634f1a7110b4 ("vsock: support sockmap") Reported-by: syzbot+bdb4bd87b5e22058e2a4@syzkaller.appspotmail.com Tested-by: syzbot+bdb4bd87b5e22058e2a4@syzkaller.appspotmail.com Cc: Bobby Eshleman <bobby.eshleman@bytedance.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://patch.msgid.link/20240812022153.86512-1-xiyou.wangcong@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Objects' dump callbacks are not concurrency-safe per-se with reset bit
set. If two CPUs perform a reset at the same time, at least counter and
quota objects suffer from value underrun.
Prevent this by introducing dedicated locking callbacks for nfnetlink
and the asynchronous dump handling to serialize access.
Fixes: 43da04a593d8 ("netfilter: nf_tables: atomic dump and reset for stateful objects") Signed-off-by: Phil Sutter <phil@nwl.cc> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In theory, dumpreset may fail and invalidate the preceeding log message.
Fix this and use the occasion to prepare for object reset locking, which
benefits from a few unrelated changes:
* Add an early call to nfnetlink_unicast if not resetting which
effectively skips the audit logging but also unindents it.
* Extract the table's name from the netlink attribute (which is verified
via earlier table lookup) to not rely upon validity of the looked up
table pointer.
* Do not use local variable family, it will vanish.
Commit 264640fc2c5f4 ("ipv6: distinguish frag queues by device
for multicast and link-local packets") modified the ipv6 fragment
reassembly logic to distinguish frag queues by device for multicast
and link-local packets but in fact only the main reassembly code
limits the use of the device to those address types and the netfilter
reassembly code uses the device for all packets.
This means that if fragments of a packet arrive on different interfaces
then netfilter will fail to reassemble them and the fragments will be
expired without going any further through the filters.
Fixes: 648700f76b03 ("inet: frags: use rhashtables for reassembly units") Signed-off-by: Tom Hughes <tom@compton.nu> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch is based on the discussions between Neal Cardwell and
Eric Dumazet in the link
https://lore.kernel.org/netdev/20240726204105.1466841-1-quic_subashab@quicinc.com/
It was correctly pointed out that tp->window_clamp would not be
updated in cases where net.ipv4.tcp_moderate_rcvbuf=0 or if
(copied <= tp->rcvq_space.space). While it is expected for most
setups to leave the sysctl enabled, the latter condition may
not end up hitting depending on the TCP receive queue size and
the pattern of arriving data.
The updated check should be hit only on initial MSS update from
TCP_MIN_MSS to measured MSS value and subsequently if there was
an update to a larger value.
Fixes: 05f76b2d634e ("tcp: Adjust clamping window for applications specifying SO_RCVBUF") Signed-off-by: Sean Tranchetti <quic_stranche@quicinc.com> Signed-off-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ssn_offset field is u32 and is placed into the netlink response with
nla_put_u32(), but only 2 bytes are reserved for the attribute payload
in subflow_get_info_size() (even though it makes no difference
in the end, as it is aligned up to 4 bytes). Supply the correct
argument to the relevant nla_total_size() call to make it less
confusing.
A recent change to the driver exposed a bug where the MAC RX
filters (unicast MAC, broadcast MAC, and multicast MAC) are
configured and enabled before the RX path is fully initialized.
The result of this bug is that after the PHY is started packets
that match these MAC RX filters start to flow into the RX FIFO.
And then, after rx_init() is completed, these packets will go
into the driver RX ring as well. If enough packets are received
to fill the RX ring (default size is 128 packets) before the call
to request_irq() completes, the driver RX function becomes stuck.
This bug is intermittent but is most likely to be seen where the
oob_net0 interface is connected to a busy network with lots of
broadcast and multicast traffic.
All the MAC RX filters must be disabled until the RX path is ready,
i.e. all initialization is done and all the IRQs are installed.
Fixes: f7442a634ac0 ("mlxbf_gige: call request_irq() after NAPI initialized") Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com> Signed-off-by: David Thompson <davthompson@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240809163612.12852-1-davthompson@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The VSC73xx has a busy flag used during MDIO operations. It is raised
when MDIO read/write operations are in progress. Without it, PHYs are
misconfigured and bus operations do not work as expected.
In axiethernet header fix register defines comment description to be
inline with IP documentation. It updates MAC configuration register,
MDIO configuration register and frame filter control description.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can't dereference "skb" after calling vcc->push() because the skb
is released.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously, an ethtool rx flow with no attrs would not be added to the
NIC as it has no rules to configure the hw with, but it would be
reported as successful to the caller (return code 0). This is confusing
for the user as ethtool then reports "Added rule $num", but no rule was
actually added.
This change corrects that by instead reporting these wrong rules as
-EINVAL.
mlx5e_safe_reopen_channels() requires the state lock taken. The
referenced changed in the Fixes tag removed the lock to fix another
issue. This patch adds it back but at a later point (when calling
mlx5e_safe_reopen_channels()) to avoid the deadlock referenced in the
Fixes tag.
Unconditionally calling the MPIR query on BF separate mode yields the FW
syndrome below [1]. Do not call it unless admin clearly specified the SD
group, i.e. expressing the intention of using the multi-PF netdev
feature.
This fix covers cases not covered in
commit fca3b4791850 ("net/mlx5: Do not query MPIR on embedded CPU function").
[1]
mlx5_cmd_out_err:808:(pid 8267): ACCESS_REG(0x805) op_mod(0x1) failed,
status bad system state(0x4), syndrome (0x685f19), err(-5)
Fixes: 678eb448055a ("net/mlx5: SD, Implement basic query and instantiation") Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Gal Pressman <gal@nvidia.com> Link: https://patch.msgid.link/20240808144107.2095424-2-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A large tx latency issue was discovered during testing when only QBV was
enabled. The issue occurs because gtxoffset was not set when QBV is
active, it was only set when launch time is active.
The patch "igc: Correct the launchtime offset" only sets gtxoffset when
the launchtime_enable field is set by the user. Enabling launchtime_enable
ultimately sets the register IGC_TXQCTL_QUEUE_MODE_LAUNCHT (referred to as
LaunchT in the SW user manual).
Section 7.5.2.6 of the IGC i225/6 SW User Manual Rev 1.2.4 states:
"The latency between transmission scheduling (launch time) and the
time the packet is transmitted to the network is listed in Table 7-61."
However, the patch misinterprets the phrase "launch time" in that section
by assuming it specifically refers to the LaunchT register, whereas it
actually denotes the generic term for when a packet is released from the
internal buffer to the MAC transmit logic.
This launch time, as per that section, also implicitly refers to the QBV
gate open time, where a packet waits in the buffer for the QBV gate to
open. Therefore, latency applies whenever QBV is in use. TSN features such
as QBU and QAV reuse QBV, making the latency universal to TSN features.
Discussed with i226 HW owner (Shalev, Avi) and we were in agreement that
the term "launch time" used in Section 7.5.2.6 is not clear and can be
easily misinterpreted. Avi will update this section to:
"When TQAVCTRL.TRANSMIT_MODE = TSN, the latency between transmission
scheduling and the time the packet is transmitted to the network is listed
in Table 7-61."
Fix this issue by using igc_tsn_is_tx_mode_in_tsn() as a condition to
write to gtxoffset, aligning with the newly updated SW User Manual.
Tested:
1. Enrol taprio on talker board
base-time 0
cycle-time 1000000
flags 0x2
index 0 cmd S gatemask 0x1 interval1
index 0 cmd S gatemask 0x1 interval2
Note:
interval1 = interval for a 64 bytes packet to go through
interval2 = cycle-time - interval1
2. Take tcpdump on listener board
3. Use udp tai app on talker to send packets to listener
Following the "igc: Fix TX Hang issue when QBV Gate is close" changes,
remaining issues with the reset adapter logic in igc_tsn_offload_apply()
have been observed:
1. The reset adapter logics for i225 and i226 differ, although they should
be the same according to the guidelines in I225/6 HW Design Section
7.5.2.1 on software initialization during tx mode changes.
2. The i225 resets adapter every time, even though tx mode doesn't change.
This occurs solely based on the condition igc_is_device_id_i225() when
calling schedule_work().
3. i226 doesn't reset adapter for tsn->legacy tx mode changes. It only
resets adapter for legacy->tsn tx mode transitions.
4. qbv_count introduced in the patch is actually not needed; in this
context, a non-zero value of qbv_count is used to indicate if tx mode
was unconditionally set to tsn in igc_tsn_enable_offload(). This could
be replaced by checking the existing register
IGC_TQAVCTRL_TRANSMIT_MODE_TSN bit.
This patch resolves all issues and enters schedule_work() to reset the
adapter only when changing tx mode. It also removes reliance on qbv_count.
qbv_count field will be removed in a future patch.
Test ran:
1. Verify reset adapter behaviour in i225/6:
a) Enrol a new GCL
Reset adapter observed (tx mode change legacy->tsn)
b) Enrol a new GCL without deleting qdisc
No reset adapter observed (tx mode remain tsn->tsn)
c) Delete qdisc
Reset adapter observed (tx mode change tsn->legacy)
2. Tested scenario from "igc: Fix TX Hang issue when QBV Gate is closed"
to confirm it remains resolved.
Fixes: 175c241288c0 ("igc: Fix TX Hang issue when QBV Gate is closed") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When user issues these cmds:
1. Either a) or b)
a) mqprio with hardware offload disabled
b) taprio with txtime-assist feature enabled
2. etf
3. tc qdisc delete
4. taprio with base time in the past
At step 4, qbv_config_change_errors wrongly increased by 1.
Excerpt from IEEE 802.1Q-2018 8.6.9.3.1:
"If AdminBaseTime specifies a time in the past, and the current schedule
is running, then: Increment ConfigChangeError counter"
qbv_config_change_errors should only increase if base time is in the past
and no taprio is active. In user perspective, taprio was not active when
first triggered at step 4. However, i225/6 reuses qbv for etf, so qbv is
enabled with a dummy schedule at step 2 where it enters
igc_tsn_enable_offload() and qbv_count got incremented to 1. At step 4, it
enters igc_tsn_enable_offload() again, qbv_count is incremented to 2.
Because taprio is running, tc_setup_type is TC_SETUP_QDISC_ETF and
qbv_count > 1, qbv_config_change_errors value got incremented.
This issue happens due to reliance on qbv_count field where a non-zero
value indicates that taprio is running. But qbv_count increases
regardless if taprio is triggered by user or by other tsn feature. It does
not align with qbv_config_change_errors expectation where it is only
concerned with taprio triggered by user.
Fixing this by relocating the qbv_config_change_errors logic to
igc_save_qbv_schedule(), eliminating reliance on qbv_count and its
inaccuracies from i225/6's multiple uses of qbv feature for other TSN
features.
The new function created: igc_tsn_is_taprio_activated_by_user() uses
taprio_offload_enable field to indicate that the current running taprio
was triggered by user, instead of triggered by non-qbv feature like etf.
Fixes: ae4fe4698300 ("igc: Add qbv_config_change_errors counter") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Testing uncovered that even when the taprio gate is closed, some packets
still transmit.
According to i225/6 hardware errata [1], traffic might overflow the
planned QBV window. This happens because MAC maintains an internal buffer,
primarily for supporting half duplex retries. Therefore, even when the
gate closes, residual MAC data in the buffer may still transmit.
To mitigate this for i226, reduce the MAC's internal buffer from 192 bytes
to the recommended 88 bytes by modifying the RETX_CTL register value.
Note that for TC3, gate should open for 500us and close for another
500us.
3. Take tcpdump log on Board B.
4. Send udp packets via UDP tai app from Board A to Board B.
5. Analyze tcpdump log via wireshark log on Board B. Ensure that the
total time from the first to the last packet received during one cycle
for TC3 does not exceed 500us.
Fixes: 43546211738e ("igc: Add new device ID's") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In __extent_writepage_io(), we call btrfs_set_range_writeback() ->
folio_start_writeback(), which clears PAGECACHE_TAG_DIRTY mark from the
mapping xarray if the folio is not dirty. This worked fine before commit 97713b1a2ced ("btrfs: do not clear page dirty inside
extent_write_locked_range()").
After the commit, however, the folio is still dirty at this point, so the
mapping DIRTY tag is not cleared anymore. Then, __extent_writepage_io()
calls btrfs_folio_clear_dirty() to clear the folio's dirty flag. That
results in the page being unlocked with a "strange" state. The page is not
PageDirty, but the mapping tag is set as PAGECACHE_TAG_DIRTY.
This strange state looks like causing a hang with a call trace below when
running fstests generic/091 on a null_blk device. It is waiting for a folio
lock.
While I don't have an exact relation between this hang and the strange
state, fixing the state also fixes the hang. And, that state is worth
fixing anyway.
This commit reorders btrfs_folio_clear_dirty() and
btrfs_set_range_writeback() in __extent_writepage_io(), so that the
PAGECACHE_TAG_DIRTY tag is properly removed from the xarray.
Daniel Hodges reported a kernel verifier crash when playing with sched-ext.
Further investigation shows that the crash is due to invalid memory access
in stacksafe(). More specifically, it is the following code:
The 'i' iterates old->allocated_stack.
If cur->allocated_stack < old->allocated_stack the out-of-bound
access will happen.
To fix the issue add 'i >= cur->allocated_stack' check such that if
the condition is true, stacksafe() should fail. Otherwise,
cur->stack[spi].slot_type[i % BPF_REG_SIZE] memory access is legal.
Fixes: 2793a8b015f7 ("bpf: exact states comparison for iterator convergence checks") Cc: Eduard Zingerman <eddyz87@gmail.com> Reported-by: Daniel Hodges <hodgesd@meta.com> Acked-by: Eduard Zingerman <eddyz87@gmail.com> Signed-off-by: Yonghong Song <yonghong.song@linux.dev> Link: https://lore.kernel.org/r/20240812214847.213612-1-yonghong.song@linux.dev Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit f7866c358733 ("bpf: Fix null pointer dereference in resolve_prog_type() for BPF_PROG_TYPE_EXT")
fixed a NULL pointer dereference panic, but didn't fix the issue that
fails to update attached freplace prog to prog_array map.
Since commit 1c123c567fb1 ("bpf: Resolve fext program type when checking map compatibility"),
freplace prog and its target prog are able to tail call each other.
And the commit 3aac1ead5eb6 ("bpf: Move prog->aux->linked_prog and trampoline into bpf_link on attach")
sets prog->aux->dst_prog as NULL after attaching freplace prog to its
target prog.
After loading freplace the prog_array's owner type is BPF_PROG_TYPE_SCHED_CLS.
Then, after attaching freplace its prog->aux->dst_prog is NULL.
Then, while updating freplace in prog_array the bpf_prog_map_compatible()
incorrectly returns false because resolve_prog_type() returns
BPF_PROG_TYPE_EXT instead of BPF_PROG_TYPE_SCHED_CLS.
After this patch the resolve_prog_type() returns BPF_PROG_TYPE_SCHED_CLS
and update to prog_array can succeed.
Fixes: f7866c358733 ("bpf: Fix null pointer dereference in resolve_prog_type() for BPF_PROG_TYPE_EXT") Cc: Toke Høiland-Jørgensen <toke@redhat.com> Cc: Martin KaFai Lau <martin.lau@kernel.org> Acked-by: Yonghong Song <yonghong.song@linux.dev> Signed-off-by: Leon Hwang <leon.hwang@linux.dev> Link: https://lore.kernel.org/r/20240728114612.48486-2-leon.hwang@linux.dev Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After we switch tmpfs dir operations from simple_dir_operations to
simple_offset_dir_operations, every rename happened will fill new dentry
to dest dir's maple tree(&SHMEM_I(inode)->dir_offsets->mt) with a free
key starting with octx->newx_offset, and then set newx_offset equals to
free key + 1. This will lead to infinite readdir combine with rename
happened at the same time, which fail generic/736 in xfstests(detail show
as below).
1. create 5000 files(1 2 3...) under one dir
2. call readdir(man 3 readdir) once, and get one entry
3. rename(entry, "TEMPFILE"), then rename("TEMPFILE", entry)
4. loop 2~3, until readdir return nothing or we loop too many
times(tmpfs break test with the second condition)
We choose the same logic what commit 9b378f6ad48cf ("btrfs: fix infinite
directory reads") to fix it, record the last_index when we open dir, and
do not emit the entry which index >= last_index. The file->private_data
now used in offset dir can use directly to do this, and we also update
the last_index when we llseek the dir file.
Fixes: a2e459555c5f ("shmem: stable directory offsets") Signed-off-by: yangerkun <yangerkun@huawei.com> Link: https://lore.kernel.org/r/20240731043835.1828697-1-yangerkun@huawei.com Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
[brauner: only update last_index after seek when offset is zero like Jan suggested] Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When struct file_lease was split out from struct file_lock, the name of
the file_lock slab cache was copied to the new slab cache for
file_lease. This name conflict causes confusion in /proc/slabinfo and
/sys/kernel/slab. In particular, it caused failures in drgn's test case
for slab cache merging.
As in commit 4e527d5841e2 ("iomap: fault in smaller chunks for non-large
folio mappings"), we can see a performance loss for filesystems
which have not yet been converted to large folios.
Fixes: c38f4e96e605 ("netfs: Provide func to copy data to pagecache for buffered write") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Link: https://lore.kernel.org/r/20240527201735.1898381-1-willy@infradead.org Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The return value uv_set_shared() and uv_remove_shared() (which are
wrappers around the share() function) is not always checked. The system
integrity of a protected guest depends on the Share and Unshare UVCs
being successful. This means that any caller that fails to check the
return value will compromise the security of the protected guest.
No code path that would lead to such violation of the security
guarantees is currently exercised, since all the areas that are shared
never get unshared during the lifetime of the system. This might
change and become an issue in the future.
The Share and Unshare UVCs can only fail in case of hypervisor
misbehaviour (either a bug or malicious behaviour). In such cases there
is no reasonable way forward, and the system needs to panic.
This patch replaces the return at the end of the share() function with
a panic, to guarantee system integrity.
Fixes: 5abb9351dfd9 ("s390/uv: introduce guest side ultravisor code") Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com> Reviewed-by: Steffen Eiden <seiden@linux.ibm.com> Reviewed-by: Janosch Frank <frankja@linux.ibm.com> Link: https://lore.kernel.org/r/20240801112548.85303-1-imbrenda@linux.ibm.com
Message-ID: <20240801112548.85303-1-imbrenda@linux.ibm.com>
[frankja@linux.ibm.com: Fixed up patch subject] Signed-off-by: Janosch Frank <frankja@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's currently possible to create pidfds for kthreads but it is unclear
what that is supposed to mean. Until we have use-cases for it and we
figured out what behavior we want block the creation of pidfds for
kthreads.
This needs to be set as well if the IB uses atomics.
Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit c6c2e8b6a427d4fecc7c36cffccb908185afcab2) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This needs to be set as well if the IB uses atomics.
Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 35c628774e50b3784c59e8ca7973f03bcb067132) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[why & how]
Cursor gets clipped off in the middle of the screen with hw
rotation 180. Fix a miscalculation of cursor offset when it's
placed near the edges in the pipe split case.
Cursor bugs with hw rotation were reported on AMD issue
tracker:
https://gitlab.freedesktop.org/drm/amd/-/issues/2247
The issues on rotation 270 was fixed by:
https://lore.kernel.org/amd-gfx/20221118125935.4013669-22-Brian.Chang@amd.com/
that partially addressed the rotation 180 too. So, this patch is the
final bits for rotation 180.
Reported-by: Xaver Hugl <xaver.hugl@gmail.com> Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2247 Reviewed-by: Harry Wentland <harry.wentland@amd.com> Fixes: 9d84c7ef8a87 ("drm/amd/display: Correct cursor position on horizontal mirror") Signed-off-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 1fd2cf090096af8a25bf85564341cfc21cec659d) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
Tiled display cannot synchronize properly after S3.
The fix for commit 5f0c74915815 ("drm/amd/display: Fix for otg
synchronization logic") is not enable in DCN321, which causes
the otg is excluded from synchronization.
[How]
Enable otg synchronization logic in dcn321.
Fixes: 5f0c74915815 ("drm/amd/display: Fix for otg synchronization logic") Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Loan Chen <lo-an.chen@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d6ed53712f583423db61fbb802606759e023bf7b) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be able to get to the lowest power state when suspending systems with
DCN3.5+, we must be in IPS before the display hardware is put into
D3cold. So, to ensure that the system always reaches the lowest power
state while suspending, force systems that support IPS to enter idle
optimizations before entering D3cold.
Reviewed-by: Roman Li <roman.li@amd.com> Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 237193e21b29d4aa0617ffeea3d6f49e72999708) Cc: stable@vger.kernel.org # 6.10+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[why & how]
When the commit 9d84c7ef8a87 ("drm/amd/display: Correct cursor position
on horizontal mirror") was introduced, it used the wrong calculation for
the position copy for X. This commit uses the correct calculation for that
based on the original patch.
Fixes: 9d84c7ef8a87 ("drm/amd/display: Correct cursor position on horizontal mirror") Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Acked-by: Wayne Lin <wayne.lin@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8f9b23abbae5ffcd64856facd26a86b67195bc2f) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although there are several patches improving the extent map shrinker,
there are still reports of too frequent shrinker behavior, taking too
much CPU for the kswapd process.
So let's only enable extent shrinker for now, until we got more
comprehensive understanding and a better solution.
[REPORT]
There is a corruption report that btrfs refused to mount a fs that has
overlapping dev extents:
BTRFS error (device sdc): dev extent devid 4 physical offset 14263979671552 overlap with previous dev extent end 14263980982272
BTRFS error (device sdc): failed to verify dev extents against chunks: -117
BTRFS error (device sdc): open_ctree failed
[CAUSE]
The direct cause is very obvious, there is a bad dev extent item with
incorrect length.
With btrfs check reporting two overlapping extents, the second one shows
some clue on the cause:
ERROR: dev extent devid 4 offset 14263979671552 len 6488064 overlap with previous dev extent end 14263980982272
ERROR: dev extent devid 13 offset 2257707008000 len 6488064 overlap with previous dev extent end 2257707270144
ERROR: errors found in extent allocation tree or chunk allocation
The second one looks like a bitflip happened during new chunk
allocation:
hex(2257707008000) = 0x20da9d30000
hex(2257707270144) = 0x20da9d70000
diff = 0x00000040000
So it looks like a bitflip happened during new dev extent allocation,
resulting the second overlap.
Currently we only do the dev-extent verification at mount time, but if the
corruption is caused by memory bitflip, we really want to catch it before
writing the corruption to the storage.
Furthermore the dev extent items has the following key definition:
(<device id> DEV_EXTENT <physical offset>)
Thus we can not just rely on the generic key order check to make sure
there is no overlapping.
[ENHANCEMENT]
Introduce dedicated dev extent checks, including:
- Fixed member checks
* chunk_tree should always be BTRFS_CHUNK_TREE_OBJECTID (3)
* chunk_objectid should always be
BTRFS_FIRST_CHUNK_CHUNK_TREE_OBJECTID (256)
- Alignment checks
* chunk_offset should be aligned to sectorsize
* length should be aligned to sectorsize
* key.offset should be aligned to sectorsize
- Overlap checks
If the previous key is also a dev-extent item, with the same
device id, make sure we do not overlap with the previous dev extent.
Reported: Stefan N <stefannnau@gmail.com> Link: https://lore.kernel.org/linux-btrfs/CA+W5K0rSO3koYTo=nzxxTm1-Pdu1HYgVxEpgJ=aGc7d=E8mGEg@mail.gmail.com/ CC: stable@vger.kernel.org # 5.10+ Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__btrfs_add_free_space_zoned() references and modifies bg's alloc_offset,
ro, and zone_unusable, but without taking the lock. It is mostly safe
because they monotonically increase (at least for now) and this function is
mostly called by a transaction commit, which is serialized by itself.
Still, taking the lock is a safer and correct option and I'm going to add a
change to reset zone_unusable while a block group is still alive. So, add
locking around the operations.
Fixes: 169e0da91a21 ("btrfs: zoned: track unusable bytes for zones") CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the extent map shrinker can be run by any task when attempting
to allocate memory and there's enough memory pressure to trigger it.
To avoid too much latency we stop iterating over extent maps and removing
them once the task needs to reschedule. This logic was introduced in commit b3ebb9b7e92a ("btrfs: stop extent map shrinker if reschedule is needed").
While that solved high latency problems for some use cases, it's still
not enough because with a too high number of tasks entering the extent map
shrinker code, either due to memory allocations or because they are a
kswapd task, we end up having a very high level of contention on some
spin locks, namely:
1) The fs_info->fs_roots_radix_lock spin lock, which we need to find
roots to iterate over their inodes;
2) The spin lock of the xarray used to track open inodes for a root
(struct btrfs_root::inodes) - on 6.10 kernels and below, it used to
be a red black tree and the spin lock was root->inode_lock;
3) The fs_info->delayed_iput_lock spin lock since the shrinker adds
delayed iputs (calls btrfs_add_delayed_iput()).
Instead of allowing the extent map shrinker to be run by any task, make
it run only by kswapd tasks. This still solves the problem of running
into OOM situations due to an unbounded extent map creation, which is
simple to trigger by direct IO writes, as described in the changelog
of commit 956a17d9d050 ("btrfs: add a shrinker for extent maps"), and
by a similar case when doing buffered IO on files with a very large
number of holes (keeping the file open and creating many holes, whose
extent maps are only released when the file is closed).
Reported-by: kzd <kzd@56709.net> Link: https://bugzilla.kernel.org/show_bug.cgi?id=219121 Reported-by: Octavia Togami <octavia.togami@gmail.com> Link: https://lore.kernel.org/linux-btrfs/CAHPNGSSt-a4ZZWrtJdVyYnJFscFjP9S7rMcvEMaNSpR556DdLA@mail.gmail.com/ Fixes: 956a17d9d050 ("btrfs: add a shrinker for extent maps") CC: stable@vger.kernel.org # 6.10+ Tested-by: kzd <kzd@56709.net> Tested-by: Octavia Togami <octavia.togami@gmail.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the patch 78c52d9eb6b7 ("btrfs: check for refs on snapshot delete
resume") I added some code to handle file systems that had been
corrupted by a bug that incorrectly skipped updating the drop progress
key while dropping a snapshot. This code would check to see if we had
already deleted our reference for a child block, and skip the deletion
if we had already.
Unfortunately there is a bug, as the check would only check the on-disk
references. I made an incorrect assumption that blocks in an already
deleted snapshot that was having the deletion resume on mount wouldn't
be modified.
If we have 2 pending deleted snapshots that share blocks, we can easily
modify the rules for a block. Take the following example
subvolume a exists, and subvolume b is a snapshot of subvolume a. They
share references to block 1. Block 1 will have 2 full references, one
for subvolume a and one for subvolume b, and it belongs to subvolume a
(btrfs_header_owner(block 1) == subvolume a).
When deleting subvolume a, we will drop our full reference for block 1,
and because we are the owner we will drop our full reference for all of
block 1's children, convert block 1 to FULL BACKREF, and add a shared
reference to all of block 1's children.
Then we will start the snapshot deletion of subvolume b. We look up the
extent info for block 1, which checks delayed refs and tells us that
FULL BACKREF is set, so sets parent to the bytenr of block 1. However
because this is a resumed snapshot deletion, we call into
check_ref_exists(). Because check_ref_exists() only looks at the disk,
it doesn't find the shared backref for the child of block 1, and thus
returns 0 and we skip deleting the reference for the child of block 1
and continue. This orphans the child of block 1.
The fix is to lookup the delayed refs, similar to what we do in
btrfs_lookup_extent_info(). However we only care about whether the
reference exists or not. If we fail to find our reference on disk, go
look up the bytenr in the delayed refs, and if it exists look for an
existing ref in the delayed ref head. If that exists then we know we
can delete the reference safely and carry on. If it doesn't exist we
know we have to skip over this block.
This bug has existed since I introduced this fix, however requires
having multiple deleted snapshots pending when we unmount. We noticed
this in production because our shutdown path stops the container on the
system, which deletes a bunch of subvolumes, and then reboots the box.
This gives us plenty of opportunities to hit this issue. Looking at the
history we've seen this occasionally in production, but we had a big
spike recently thanks to faster machines getting jobs with multiple
subvolumes in the job.
Chris Mason wrote a reproducer which does the following
On the second loop this would fail consistently, with my patch it has
been running for hours and hasn't failed.
I also used dm-log-writes to capture the state of the failure so I could
debug the problem. Using the existing failure case to test my patch
validated that it fixes the problem.
Fixes: 78c52d9eb6b7 ("btrfs: check for refs on snapshot delete resume") CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we a find that an extent is shared but its end offset is not sector
size aligned, then we don't clone it and issue write operations instead.
This is because the reflink (remap_file_range) operation does not allow
to clone unaligned ranges, except if the end offset of the range matches
the i_size of the source and destination files (and the start offset is
sector size aligned).
While this is not incorrect because send can only guarantee that a file
has the same data in the source and destination snapshots, it's not
optimal and generates confusion and surprising behaviour for users.
For example, running this test:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV
mount $DEV $MNT
# Use a file size not aligned to any possible sector size.
file_size=$((1 * 1024 * 1024 + 5)) # 1MB + 5 bytes
dd if=/dev/random of=$MNT/foo bs=$file_size count=1
cp --reflink=always $MNT/foo $MNT/bar
[REPORT]
There is a bug report that kernel is rejecting a mismatching inode mode
and its dir item:
[ 1881.553937] BTRFS critical (device dm-0): inode mode mismatch with
dir: inode mode=040700 btrfs type=2 dir type=0
[CAUSE]
It looks like the inode mode is correct, while the dir item type
0 is BTRFS_FT_UNKNOWN, which should not be generated by btrfs at all.
This may be caused by a memory bit flip.
[ENHANCEMENT]
Although tree-checker is not able to do any cross-leaf verification, for
this particular case we can at least reject any dir type with
BTRFS_FT_UNKNOWN.
So here we enhance the dir type check from [0, BTRFS_FT_MAX), to
(0, BTRFS_FT_MAX).
Although the existing corruption can not be fixed just by such enhanced
checking, it should prevent the same 0x2->0x0 bitflip for dir type to
reach disk in the future.
When handling a numa page fault, task_numa_fault() should be called by a
process that restores the page table of the faulted folio to avoid
duplicated stats counting. Commit b99a342d4f11 ("NUMA balancing: reduce
TLB flush via delaying mapping on hint page fault") restructured
do_numa_page() and did not avoid task_numa_fault() call in the second page
table check after a numa migration failure. Fix it by making all
!pte_same() return immediately.
This issue can cause task_numa_fault() being called more than necessary
and lead to unexpected numa balancing results (It is hard to tell whether
the issue will cause positive or negative performance impact due to
duplicated numa fault counting).
Link: https://lkml.kernel.org/r/20240809145906.1513458-2-ziy@nvidia.com Fixes: b99a342d4f11 ("NUMA balancing: reduce TLB flush via delaying mapping on hint page fault") Signed-off-by: Zi Yan <ziy@nvidia.com> Reported-by: "Huang, Ying" <ying.huang@intel.com> Closes: https://lore.kernel.org/linux-mm/87zfqfw0yw.fsf@yhuang6-desk2.ccr.corp.intel.com/ Acked-by: David Hildenbrand <david@redhat.com> Cc: Baolin Wang <baolin.wang@linux.alibaba.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The __vmap_pages_range_noflush() assumes its argument pages** contains
pages with the same page shift. However, since commit e9c3cda4d86e ("mm,
vmalloc: fix high order __GFP_NOFAIL allocations"), if gfp_flags includes
__GFP_NOFAIL with high order in vm_area_alloc_pages() and page allocation
failed for high order, the pages** may contain two different page shifts
(high order and order-0). This could lead __vmap_pages_range_noflush() to
perform incorrect mappings, potentially resulting in memory corruption.
Users might encounter this as follows (vmap_allow_huge = true, 2M is for
PMD_SIZE):
We can remove the fallback code because if a high-order allocation fails,
__vmalloc_node_range_noprof() will retry with order-0. Therefore, it is
unnecessary to fallback to order-0 here. Therefore, fix this by removing
the fallback code.
Link: https://lkml.kernel.org/r/20240808122019.3361-1-hailong.liu@oppo.com Fixes: e9c3cda4d86e ("mm, vmalloc: fix high order __GFP_NOFAIL allocations") Signed-off-by: Hailong Liu <hailong.liu@oppo.com> Reported-by: Tangquan Zheng <zhengtangquan@oppo.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Barry Song <baohua@kernel.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling a numa page fault, task_numa_fault() should be called by a
process that restores the page table of the faulted folio to avoid
duplicated stats counting. Commit c5b5a3dd2c1f ("mm: thp: refactor NUMA
fault handling") restructured do_huge_pmd_numa_page() and did not avoid
task_numa_fault() call in the second page table check after a numa
migration failure. Fix it by making all !pmd_same() return immediately.
This issue can cause task_numa_fault() being called more than necessary
and lead to unexpected numa balancing results (It is hard to tell whether
the issue will cause positive or negative performance impact due to
duplicated numa fault counting).
Link: https://lkml.kernel.org/r/20240809145906.1513458-3-ziy@nvidia.com Fixes: c5b5a3dd2c1f ("mm: thp: refactor NUMA fault handling") Reported-by: "Huang, Ying" <ying.huang@intel.com> Closes: https://lore.kernel.org/linux-mm/87zfqfw0yw.fsf@yhuang6-desk2.ccr.corp.intel.com/ Signed-off-by: Zi Yan <ziy@nvidia.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Baolin Wang <baolin.wang@linux.alibaba.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
