If the SPI data size is smaller than FIFO, it operates in PIO mode,
and if it is larger than FIFO size, it oerates in DMA mode.
If the SPI data size is equal to fifo, it operates in PIO mode and it is
separated to 2 transfers. To prevent it, it must operate in DMA mode
from the case where the data size and the fifo size are the same.
Fixes: 1ee806718d5e ("spi: s3c64xx: support interrupt based pio mode") Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Link: https://lore.kernel.org/r/20240329085840.65856-1-jaewon02.kim@samsung.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver is wrong because is using partial register field masks for the
SPI_STATUS.{RX, TX}_FIFO_LVL register fields.
We see s3c64xx_spi_port_config.fifo_lvl_mask with different values for
different instances of the same IP. Take s5pv210_spi_port_config for
example, it defines:
.fifo_lvl_mask = { 0x1ff, 0x7F },
fifo_lvl_mask is used to determine the FIFO depth of the instance of the
IP. In this case, the integrator uses a 256 bytes FIFO for the first SPI
instance of the IP, and a 64 bytes FIFO for the second instance. While
the first mask reflects the SPI_STATUS.{RX, TX}_FIFO_LVL register
fields, the second one is two bits short. Using partial field masks is
misleading and can hide problems of the driver's logic.
Allow platforms to specify the full FIFO mask, regardless of the FIFO
depth.
Introduce {rx, tx}_fifomask to represent the SPI_STATUS.{RX, TX}_FIFO_LVL
register fields. It's a shifted mask defining the field's length and
position. We'll be able to deprecate the use of @rx_lvl_offset, as the
shift value can be determined from the mask. The existing compatibles
shall start using {rx, tx}_fifomask so that they use the full field mask
and to avoid shifting the mask to position, and then shifting it back to
zero in the {TX, RX}_FIFO_LVL macros.
@rx_lvl_offset will be deprecated in a further patch, after we have the
infrastructure to deprecate @fifo_lvl_mask as well.
The driver uses GENMASK() but does not include <linux/bits.h>.
It is good practice to directly include all headers used, it avoids
implicit dependencies and spurious breakage if someone rearranges
headers and causes the implicit include to vanish.
Include the missing header.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org> Link: https://lore.kernel.org/r/20240207120431.2766269-4-tudor.ambarus@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: a3d3eab627bb ("spi: s3c64xx: Use DMA mode from fifo size") Signed-off-by: Sasha Levin <sashal@kernel.org>
In snd_soc_info_volsw(), mask is generated by figuring out the index of
the most significant bit set in max and converting the index to a
bitmask through bit shift 1. Unintended wraparound occurs when max is an
integer value with msb bit set. Since the bit shift value 1 is treated
as an integer type, the left shift operation will wraparound and set
mask to 0 instead of all 1's. In order to fix this, we type cast 1 as
`1ULL` to prevent the wraparound.
Fixes: 7077148fb50a ("ASoC: core: Split ops out of soc-core.c") Signed-off-by: Stephen Lee <slee08177@gmail.com> Link: https://msgid.link/r/20240326010131.6211-1-slee08177@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
virtgpu "vram" GEM objects do not implement obj->get_sg_table(). But
they also don't use drm_gem_map_dma_buf(). In fact they may not even
have guest visible pages. But it is perfectly fine to export and share
with other virtual devices.
Reported-by: Dominik Behr <dbehr@chromium.org> Fixes: 207395da5a97 ("drm/prime: reject DMA-BUF attach when get_sg_table is missing") Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Simon Ser <contact@emersion.fr> Signed-off-by: Simon Ser <contact@emersion.fr> Link: https://patchwork.freedesktop.org/patch/msgid/20240322214801.319975-1-robdclark@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Increase the timeout value to prevent system logs on Amlogic boards flooding
with power transition warnings:
[ 13.047638] panfrost ffe40000.gpu: shader power transition timeout
[ 13.048674] panfrost ffe40000.gpu: l2 power transition timeout
[ 13.937324] panfrost ffe40000.gpu: shader power transition timeout
[ 13.938351] panfrost ffe40000.gpu: l2 power transition timeout
...
[39829.506904] panfrost ffe40000.gpu: shader power transition timeout
[39829.507938] panfrost ffe40000.gpu: l2 power transition timeout
[39949.508369] panfrost ffe40000.gpu: shader power transition timeout
[39949.509405] panfrost ffe40000.gpu: l2 power transition timeout
The 2000 value has been found through trial and error testing with devices
using G52 and G31 GPUs.
Fixes: 22aa1a209018 ("drm/panfrost: Really power off GPU cores in panfrost_gpu_power_off()") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Steven Price <steven.price@arm.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Steven Price <steven.price@arm.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240322164525.2617508-1-christianshewitt@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Adding the ACPI HIDs to the match table triggers the cs35l56-hda modules
to be loaded on boot so that Serial Multi Instantiate can add the
devices to the bus and begin the driver init sequence.
When keeping the upper end of a cache block entry, the entry[] array
must be indexed by the offset from the base register of the block,
i.e. max - mas.index.
The code was indexing entry[] by only the register address, leading
to an out-of-bounds access that copied some part of the kernel
memory over the cache contents.
This bug was not detected by the regmap KUnit test because it only
tests with a block of registers starting at 0, so mas.index == 0.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: f033c26de5a5 ("regmap: Add maple tree based register cache") Link: https://msgid.link/r/20240327114406.976986-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
"riscv: signal: Report signal frame size to userspace via auxv" (e92f469)
has added new constant AT_MINSIGSTKSZ but failed to increment the size of
auxv, keeping AT_VECTOR_SIZE_ARCH at 9.
This fix correctly increments AT_VECTOR_SIZE_ARCH to 10, following the
approach in the commit 94b07c1 ("arm64: signal: Report signal frame size
to userspace via auxv").
The original changes in v6.8 do allow for a block device to be reopened
with BLK_OPEN_RESTRICT_WRITES provided the same holder is used as per
bdev_may_open(). I think this has a bug.
The first opener @f1 of that block device will set bdev->bd_writers to
-1. The second opener @f2 using the same holder will pass the check in
bdev_may_open() that bdev->bd_writers must not be greater than zero.
The first opener @f1 now closes the block device and in bdev_release()
will end up calling bdev_yield_write_access() which calls
bdev_writes_blocked() and sets bdev->bd_writers to 0 again.
Now @f2 holds a file to that block device which was opened with
exclusive write access but bdev->bd_writers has been reset to 0.
So now @f3 comes along and succeeds in opening the block device with
BLK_OPEN_WRITE betraying @f2's request to have exclusive write access.
This isn't a practical issue yet because afaict there's no codepath
inside the kernel that reopenes the same block device with
BLK_OPEN_RESTRICT_WRITES but it will be if there is.
Fix this by counting the number of BLK_OPEN_RESTRICT_WRITES openers. So
we only allow writes again once all BLK_OPEN_RESTRICT_WRITES openers are
done.
Link: https://lore.kernel.org/r/20240323-abtauchen-klauen-c2953810082d@brauner Fixes: ed5cc702d311 ("block: Add config option to not allow writing to mounted devices") Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
RISC-V perf driver does not yet support branch sampling. Although the
specification is in the works [0], it is best to disable such events
until support is available, otherwise we will get unexpected results.
Due to this reason, two riscv bpf testcases get_branch_snapshot and
perf_branches/perf_branches_hw fail.
Such relocation causes crash of android linker similar to one
described in commit e05d57dcb8c7
("riscv: Fixup __vdso_gettimeofday broke dynamic ftrace").
Looks like this relocation is added by CONFIG_DYNAMIC_FTRACE which is
disabled in the default android kernel.
Before:
readelf -rW arch/riscv/kernel/vdso/vdso.so:
Relocation section '.rela.dyn' at offset 0xd00 contains 1 entry:
Offset Info Type 0000000000000d200000000000000003 R_RISCV_RELATIVE
__flush_tlb_range() does not modify the provided cpumask, so its cmask
parameter can be pointer-to-const. This avoids the unsafe cast of
cpu_online_mask.
Fixes: 54d7431af73e ("riscv: Add support for BATCHED_UNMAP_TLB_FLUSH") Signed-off-by: Samuel Holland <samuel.holland@sifive.com> Reviewed-by: Andrew Jones <ajones@ventanamicro.com> Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com> Link: https://lore.kernel.org/r/20240301201837.2826172-1-samuel.holland@sifive.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current code is pulling the wrong pointer causing it to disable the
wrong IRQ. Correct the code to pull the correct cs42l43 core data
pointer.
Fixes: 64353af49fec ("ASoC: cs42l43: Add system suspend ops to disable IRQ") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://msgid.link/r/20240326105434.852907-1-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
wm_adsp_write_ctl() must hold the pwr_lock mutex when calling
cs_dsp_get_ctl().
This was previously partially fixed by commit 781118bc2fc1
("ASoC: wm_adsp: Fix missing locking in wm_adsp_[read|write]_ctl()")
but this only put locking around the call to cs_dsp_coeff_write_ctrl(),
missing the call to cs_dsp_get_ctl().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 781118bc2fc1 ("ASoC: wm_adsp: Fix missing locking in wm_adsp_[read|write]_ctl()") Link: https://msgid.link/r/20240307110227.41421-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previous conversion to iov missed these debug statements which would now
always print the requested size instead of the actual server reply.
Write also added a loop in a much older commit but we didn't report
these, while reads do report each iteration -- it's more coherent to
keep reporting all requests to server so move that at the same time.
Fixes: 7f02464739da ("9p: convert to advancing variant of iov_iter_get_pages_alloc()") Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Message-ID: <20240109-9p-rw-trace-v1-1-327178114257@codewreck.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current MPTCP servers increment MPTcpExtMPCapableFallbackACK when they
accept non-MPC connections. As reported by Christoph, this is "surprising"
because the counter might become greater than MPTcpExtMPCapableSYNRX.
MPTcpExtMPCapableFallbackACK counter's name suggests it should only be
incremented when a connection was seen using MPTCP options, then a
fallback to TCP has been done. Let's do that by incrementing it when
the subflow context of an inbound MPC connection attempt is dropped.
Also, update mptcp_connect.sh kselftest, to ensure that the
above MIB does not increment in case a pure TCP client connects to a
MPTCP server.
Fixes: fc518953bc9c ("mptcp: add and use MIB counter infrastructure") Cc: stable@vger.kernel.org Reported-by: Christoph Paasch <cpaasch@apple.com> Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/449 Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://lore.kernel.org/r/20240329-upstream-net-20240329-fallback-mib-v1-1-324a8981da48@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch uses addition assignment operator (+=) to append strings
instead of duplicating the variable name in mptcp_connect.sh and
mptcp_join.sh.
This can make the statements shorter.
Note: in mptcp_connect.sh, add a local variable extra in do_transfer to
save the various extra warning logs, using += to append it. And add a
new variable tc_info to save various tc info, also using += to append it.
This can make the code more readable and prepare for the next commit.
shellcheck recently helped to prevent issues. It is then good to fix the
other harmless issues in order to spot "real" ones later.
Here, two categories of warnings are now ignored:
- SC2317: Command appears to be unreachable. The cleanup() function is
invoked indirectly via the EXIT trap.
- SC2086: Double quote to prevent globbing and word splitting. This is
recommended, but the current usage is correct and there is no need to
do all these modifications to be compliant with this rule.
For the modifications:
- SC2034: ksft_skip appears unused.
- SC2181: Check exit code directly with e.g. 'if mycmd;', not
indirectly with $?.
- SC2004: $/${} is unnecessary on arithmetic variables.
- SC2155: Declare and assign separately to avoid masking return
values.
- SC2166: Prefer [ p ] && [ q ] as [ p -a q ] is not well defined.
- SC2059: Don't use variables in the printf format string. Use printf
'..%s..' "$foo".
Now this script is shellcheck (0.9.0) compliant. We can easily spot new
issues.
Some BIOSes allow the end user to set the minimum SEV ASID value
(CPUID 0x8000001F_EDX) to be greater than the maximum number of
encrypted guests, or maximum SEV ASID value (CPUID 0x8000001F_ECX)
in order to dedicate all the SEV ASIDs to SEV-ES or SEV-SNP.
The SEV support, as coded, does not handle the case where the minimum
SEV ASID value can be greater than the maximum SEV ASID value.
As a result, the following confusing message is issued:
[ 30.715724] kvm_amd: SEV enabled (ASIDs 1007 - 1006)
Convert all local ASID variables and parameters throughout the SEV code
from signed integers to unsigned integers. As ASIDs are fundamentally
unsigned values, and the global min/max variables are appropriately
unsigned integers, too.
Functionally, this is a glorified nop as KVM guarantees min_sev_asid is
non-zero, and no CPU supports -1u as the _only_ asid, i.e. the signed vs.
unsigned goof won't cause problems in practice.
Opportunistically use sev_get_asid() in sev_flush_encrypted_page() instead
of open coding an equivalent.
The error statistics should be updated each time the poll function is
called, even if the full RX work budget has been consumed. This prevents
the counts from becoming stuck when RX bandwidth usage is high.
This also ensures that error counters are not updated after we've
re-enabled interrupts as that could result in a race condition.
The TX queue should be serviced each time the poll function is called,
even if the full RX work budget has been consumed. This prevents
starvation of the TX queue when RX bandwidth usage is high.
ravb_poll() initial code used to interrogate the first descriptor of the
RX queue in case gPTP is false to determine if ravb_rx() should be called.
This is done for non-gPTP IPs. For gPTP IPs the driver PTP-specific
information was used to determine if receive function should be called. As
every IP has its own receive function that interrogates the RX descriptors
list in the same way the ravb_poll() was doing there is no need to double
check this in ravb_poll(). Removing the code from ravb_poll() leads to a
cleaner code.
mean_and_variance_test_2 and mean_and_variance_test_4 always fail.
The input parameters to those tests are identical to the input parameters
to tests 1 and 3, yet the expected result for tests 2 and 4 is different
for the mean and stddev tests. That will always fail.
Forcing SMBUS inside the ULP enabling flow leads to sporadic PHY loss on
some systems. It is suspected to be caused by initiating PHY transactions
before the interface settles.
Separating this configuration from the ULP enabling flow and moving it to
the shutdown function allows enough time for the interface to settle and
avoids adding a delay.
Fixes: 6607c99e7034 ("e1000e: i219 - fix to enable both ULP and EEE in Sx state") Co-developed-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add curly braces to avoid entering to an if statement where it is not
always required in e1000_shutdown function.
This improves code readability and might prevent non-deterministic
behaviour in the future.
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20240301184806.2634508-5-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 861e8086029e ("e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue") Signed-off-by: Sasha Levin <sashal@kernel.org>
As for ice bug fixed by commit b7306b42beaf ("ice: manage interrupts
during poll exit") followed by commit 23be7075b318 ("ice: fix software
generating extra interrupts") I'm seeing the similar issue also with
i40e driver.
In certain situation when busy-loop is enabled together with adaptive
coalescing, the driver occasionally misses that there are outstanding
descriptors to clean when exiting busy poll.
Try to catch the remaining work by triggering a software interrupt
when exiting busy poll. No extra interrupts will be generated when
busy polling is not used.
The issue was found when running sockperf ping-pong tcp test with
adaptive coalescing and busy poll enabled (50 as value busy_pool
and busy_read sysctl knobs) and results in huge latency spikes
with more than 100000us.
The fix is inspired from the ice driver and do the following:
1) During napi poll exit in case of busy-poll (napo_complete_done()
returns false) this is recorded to q_vector that we were in busy
loop.
2) Extends i40e_buildreg_itr() to be able to add an enforced software
interrupt into built value
2) In i40e_update_enable_itr() enforces a software interrupt trigger
if we are exiting busy poll to catch any pending clean-ups
3) Reuses unused 3rd ITR (interrupt throttle) index and set it to
20K interrupts per second to limit the number of these sw interrupts.
Test results
============
Prior:
[root@dell-per640-07 net]# sockperf ping-pong -i 10.9.9.1 --tcp -m 1000 --mps=max -t 120
sockperf: == version #3.10-no.git ==
sockperf[CLIENT] send on:sockperf: using recvfrom() to block on socket(s)
Fixes: 0bcd952feec7 ("ethernet/intel: consolidate NAPI and NAPI exit") Reported-by: Hugo Ferreira <hferreir@redhat.com> Reviewed-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To fix the regression introduced by commit 52424f974bc5, which causes
servers hang in very hard to reproduce conditions with resets races.
Using two sources for the information is the root cause.
In this function before the fix bumping v didn't mean bumping vf
pointer. But the code used this variables interchangeably, so stale vf
could point to different/not intended vf.
Remove redundant "v" variable and iterate via single VF pointer across
whole function instead to guarantee VF pointer validity.
Fixes: 52424f974bc5 ("i40e: Fix VF hang when reset is triggered on another VF") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug usually affects untrusted VFs, because they are limited to 18 MACs,
it affects them badly, not letting to create MAC all filters.
Not stable to reproduce, it happens when VF user creates MAC filters
when other MACVLAN operations are happened in parallel.
But consequence is that VF can't receive desired traffic.
Fix counter to be bumped only for new or active filters.
Fixes: 621650cabee5 ("i40e: Refactoring VF MAC filters counting to make more reliable") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rvu_map_cgx_lmac_pf() the 'iter', which is used as an array index, can reach
value (up to 14) that exceed the size (MAX_LMAC_COUNT = 8) of the array.
Fix this bug by adding 'iter' value check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 91c6945ea1f9 ("octeontx2-af: cn10k: Add RPM MAC support") Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation for loading coalesced KPU profiles has
a limitation. The "offset" field, which is used to locate profiles
within the profile is restricted to a u16.
This restricts the number of profiles that can be loaded. This patch
addresses this limitation by increasing the size of the "offset" field.
Fixes: 11c730bfbf5b ("octeontx2-af: support for coalescing KPU profiles") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GRO has a fundamental issue with UDP tunnel packets as it can't detect
those in a foolproof way and GRO could happen before they reach the
tunnel endpoint. Previous commits have fixed issues when UDP tunnel
packets come from a remote host, but if those packets are issued locally
they could run into checksum issues.
If the inner packet has a partial checksum the information will be lost
in the GRO logic, either in udp4/6_gro_complete or in
udp_gro_complete_segment and packets will have an invalid checksum when
leaving the host.
Prevent local UDP tunnel packets from ever being GROed at the outer UDP
level.
Due to skb->encapsulation being wrongly used in some drivers this is
actually only preventing UDP tunnel packets with a partial checksum to
be GROed (see iptunnel_handle_offloads) but those were also the packets
triggering issues so in practice this should be sufficient.
Fixes: 9fd1ff5d2ac7 ("udp: Support UDP fraglist GRO/GSO.") Fixes: 36707061d6ba ("udp: allow forwarding of plain (non-fraglisted) UDP GRO packets") Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Antoine Tenart <atenart@kernel.org> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UDP GRO validates checksums and in udp4/6_gro_complete fraglist packets
are converted to CHECKSUM_UNNECESSARY to avoid later checks. However
this is an issue for CHECKSUM_PARTIAL packets as they can be looped in
an egress path and then their partial checksums are not fixed.
Different issues can be observed, from invalid checksum on packets to
traces like:
Fix this by only converting CHECKSUM_NONE packets to
CHECKSUM_UNNECESSARY by reusing __skb_incr_checksum_unnecessary. All
other checksum types are kept as-is, including CHECKSUM_COMPLETE as
fraglist packets being segmented back would have their skb->csum valid.
Fixes: 9fd1ff5d2ac7 ("udp: Support UDP fraglist GRO/GSO.") Signed-off-by: Antoine Tenart <atenart@kernel.org> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When rx-udp-gro-forwarding is enabled UDP packets might be GROed when
being forwarded. If such packets might land in a tunnel this can cause
various issues and udp_gro_receive makes sure this isn't the case by
looking for a matching socket. This is performed in
udp4/6_gro_lookup_skb but only in the current netns. This is an issue
with tunneled packets when the endpoint is in another netns. In such
cases the packets will be GROed at the UDP level, which leads to various
issues later on. The same thing can happen with rx-gro-list.
We saw this with geneve packets being GROed at the UDP level. In such
case gso_size is set; later the packet goes through the geneve rx path,
the geneve header is pulled, the offset are adjusted and frag_list skbs
are not adjusted with regard to geneve. When those skbs hit
skb_fragment, it will misbehave. Different outcomes are possible
depending on what the GROed skbs look like; from corrupted packets to
kernel crashes.
One example is a BUG_ON[1] triggered in skb_segment while processing the
frag_list. Because gso_size is wrong (geneve header was pulled)
skb_segment thinks there is "geneve header size" of data in frag_list,
although it's in fact the next packet. The BUG_ON itself has nothing to
do with the issue. This is only one of the potential issues.
Looking up for a matching socket in udp_gro_receive is fragile: the
lookup could be extended to all netns (not speaking about performances)
but nothing prevents those packets from being modified in between and we
could still not find a matching socket. It's OK to keep the current
logic there as it should cover most cases but we also need to make sure
we handle tunnel packets being GROed too early.
This is done by extending the checks in udp_unexpected_gso: GSO packets
lacking the SKB_GSO_UDP_TUNNEL/_CSUM bits and landing in a tunnel must
be segmented.
[1] kernel BUG at net/core/skbuff.c:4408!
RIP: 0010:skb_segment+0xd2a/0xf70
__udp_gso_segment+0xaa/0x560
Fixes: 9fd1ff5d2ac7 ("udp: Support UDP fraglist GRO/GSO.") Fixes: 36707061d6ba ("udp: allow forwarding of plain (non-fraglisted) UDP GRO packets") Signed-off-by: Antoine Tenart <atenart@kernel.org> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On devices that support DASH, the current code in the "rtl_loop_wait" function
raises false alarms when DASH is disabled. This occurs because the function
attempts to wait for the DASH firmware to be ready, even though it's not
relevant in this case.
This patch modifies the driver start/stop functions to skip checking the DASH
firmware status when DASH is explicitly disabled. This prevents unnecessary
delays and false alarms.
The patch has been tested on several ThinkStation P8/PX workstations.
Fixes: 0ab0c45d8aae ("r8169: add handling DASH when DASH is disabled") Signed-off-by: Atlas Yu <atlas.yu@canonical.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/20240328055152.18443-1-atlas.yu@canonical.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mlxbf_gige driver intermittantly encounters a NULL pointer
exception while the system is shutting down via "reboot" command.
The mlxbf_driver will experience an exception right after executing
its shutdown() method. One example of this exception is:
During system shutdown, the mlxbf_gige driver's shutdown() is always executed.
However, the driver's stop() method will only execute if networking interface
configuration logic within the Linux distribution has been setup to do so.
If shutdown() executes but stop() does not execute, NAPI remains enabled
and this can lead to an exception if NAPI is scheduled while the hardware
interface has only been partially deinitialized.
The networking interface managed by the mlxbf_gige driver must be properly
stopped during system shutdown so that IFF_UP is cleared, the hardware
interface is put into a clean state, and NAPI is fully deinitialized.
syzkaller reported infinite recursive calls of fib6_dump_done() during
netlink socket destruction. [1]
From the log, syzkaller sent an AF_UNSPEC RTM_GETROUTE message, and then
the response was generated. The following recvmmsg() resumed the dump
for IPv6, but the first call of inet6_dump_fib() failed at kzalloc() due
to the fault injection. [0]
Here, fib6_dump_done() was set to nlk_sk(sk)->cb.done, and the next call
of inet6_dump_fib() set it to nlk_sk(sk)->cb.args[3]. syzkaller stopped
receiving the response halfway through, and finally netlink_sock_destruct()
called nlk_sk(sk)->cb.done().
fib6_dump_done() calls fib6_dump_end() and nlk_sk(sk)->cb.done() if it
is still not NULL. fib6_dump_end() rewrites nlk_sk(sk)->cb.done() by
nlk_sk(sk)->cb.args[3], but it has the same function, not NULL, calling
itself recursively and hitting the stack guard page.
To avoid the issue, let's set the destructor after kzalloc().
[0]:
FAULT_INJECTION: forcing a failure.
name failslab, interval 1, probability 0, space 0, times 0
CPU: 1 PID: 432110 Comm: syz-executor.3 Not tainted 6.8.0-12821-g537c2e91d354-dirty #11
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:117)
should_fail_ex (lib/fault-inject.c:52 lib/fault-inject.c:153)
should_failslab (mm/slub.c:3733)
kmalloc_trace (mm/slub.c:3748 mm/slub.c:3827 mm/slub.c:3992)
inet6_dump_fib (./include/linux/slab.h:628 ./include/linux/slab.h:749 net/ipv6/ip6_fib.c:662)
rtnl_dump_all (net/core/rtnetlink.c:4029)
netlink_dump (net/netlink/af_netlink.c:2269)
netlink_recvmsg (net/netlink/af_netlink.c:1988)
____sys_recvmsg (net/socket.c:1046 net/socket.c:2801)
___sys_recvmsg (net/socket.c:2846)
do_recvmmsg (net/socket.c:2943)
__x64_sys_recvmmsg (net/socket.c:3041 net/socket.c:3034 net/socket.c:3034)
On some Meteor Lake systems accessing the PHY via the MDIO interface may
result in an MDI error. This issue happens sporadically and in most cases
a second access to the PHY via the MDIO interface results in success.
As a workaround, introduce a retry counter which is set to 3 on Meteor
Lake systems. The driver will only return an error if 3 consecutive PHY
access attempts fail. The retry mechanism is disabled in specific flows,
where MDI errors are expected.
Fixes: cc23f4f0b6b9 ("e1000e: Add support for Meteor Lake") Suggested-by: Nikolay Mushayev <nikolay.mushayev@intel.com> Co-developed-by: Nir Efrati <nir.efrati@intel.com> Signed-off-by: Nir Efrati <nir.efrati@intel.com> Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ax25 device is detaching, the ax25_dev_device_down()
calls ax25_ds_del_timer() to cleanup the slave_timer. When
the timer handler is running, the ax25_ds_del_timer() that
calls del_timer() in it will return directly. As a result,
the use-after-free bugs could happen, one of the scenarios
is shown below:
Jianguo Wu reported another bind() regression introduced by bhash2.
Calling bind() for the following 3 addresses on the same port, the
3rd one should fail but now succeeds.
1. 0.0.0.0 or ::ffff:0.0.0.0
2. [::] w/ IPV6_V6ONLY
3. IPv4 non-wildcard address or v4-mapped-v6 non-wildcard address
The first two bind() create tb2 like this:
bhash2 -> tb2(:: w/ IPV6_V6ONLY) -> tb2(0.0.0.0)
The 3rd bind() will match with the IPv6 only wildcard address bucket
in inet_bind2_bucket_match_addr_any(), however, no conflicting socket
exists in the bucket. So, inet_bhash2_conflict() will returns false,
and thus, inet_bhash2_addr_any_conflict() returns false consequently.
As a result, the 3rd bind() bypasses conflict check, which should be
done against the IPv4 wildcard address bucket.
So, in inet_bhash2_addr_any_conflict(), we must iterate over all buckets.
Note that we cannot add ipv6_only flag for inet_bind2_bucket as it
would confuse the following patetrn.
1. [::] w/ SO_REUSE{ADDR,PORT} and IPV6_V6ONLY
2. [::] w/ SO_REUSE{ADDR,PORT}
3. IPv4 non-wildcard address or v4-mapped-v6 non-wildcard address
The first bind() would create a bucket with ipv6_only flag true,
the second bind() would add the [::] socket into the same bucket,
and the third bind() could succeed based on the wrong assumption
that ipv6_only bucket would not conflict with v4(-mapped-v6) address.
Fixes: 28044fc1d495 ("net: Add a bhash2 table hashed by port and address") Diagnosed-by: Jianguo Wu <wujianguo106@163.com> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20240326204251.51301-3-kuniyu@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The netdev CI runs in a VM and captures serial, so stdout and
stderr get combined. Because there's a missing new line in
stderr the test ends up corrupting KTAP:
# Successok 1 selftests: net: reuseaddr_conflict
which should have been:
# Success
ok 1 selftests: net: reuseaddr_conflict
Fixes: 422d8dc6fd3a ("selftest: add a reuseaddr test") Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com> Link: https://lore.kernel.org/r/20240329160559.249476-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Issue is that ip6erspan_rcv() (and erspan_rcv()) no longer make
sure erspan_base_hdr is present in skb linear part (skb->head)
before getting @ver field from it.
Add the missing pskb_may_pull() calls.
v2: Reload iph pointer in erspan_rcv() after pskb_may_pull()
because skb->head might have changed.
Commit 5e07e672412b ("tcp: Use bhash2 for v4-mapped-v6 non-wildcard
address.") introduced bind() regression for v4-mapped-v6 address.
When we bind() the following two addresses on the same port, the 2nd
bind() should succeed but fails now.
1. [::] w/ IPV6_ONLY
2. ::ffff:127.0.0.1
After the chagne, v4-mapped-v6 uses bhash2 instead of bhash to
detect conflict faster, but I forgot to add a necessary change.
During the 2nd bind(), inet_bind2_bucket_match_addr_any() returns
the tb2 bucket of [::], and inet_bhash2_conflict() finally calls
inet_bind_conflict(), which returns true, meaning conflict.
inet_bhash2_addr_any_conflict
|- inet_bind2_bucket_match_addr_any <-- return [::] bucket
`- inet_bhash2_conflict
`- __inet_bhash2_conflict <-- checks IPV6_ONLY for AF_INET
| but not for v4-mapped-v6 address
`- inet_bind_conflict <-- does not check address
inet_bind_conflict() does not check socket addresses because
__inet_bhash2_conflict() is expected to do so.
However, it checks IPV6_V6ONLY attribute only against AF_INET
socket, and not for v4-mapped-v6 address.
As a result, v4-mapped-v6 address conflicts with v6-only wildcard
address.
To avoid that, let's add the missing test to use bhash2 for
v4-mapped-v6 address.
Fixes: 5e07e672412b ("tcp: Use bhash2 for v4-mapped-v6 non-wildcard address.") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20240326204251.51301-2-kuniyu@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 73d9629e1c8c ("i40e: Do not allow untrusted VF to remove
administratively set MAC") fixed an issue where untrusted VF was
allowed to remove its own MAC address although this was assigned
administratively from PF. Unfortunately the introduced check
is wrong because it causes that MAC filters for other MAC addresses
including multi-cast ones are not removed.
if (i40e_del_mac_filter(vsi, al->list[i].addr)) {
...
</snip>
The else path with `continue` effectively skips any MAC filter
removal except one for primary MAC addr when VF is allowed to do so.
Fix the check condition so the `continue` is only done for primary
MAC address.
Fixes: 73d9629e1c8c ("i40e: Do not allow untrusted VF to remove administratively set MAC") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Michal Schmidt <mschmidt@redhat.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20240329180638.211412-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ice_port_vlan_on/off() was introduced in commit 2946204b3fa8 ("ice:
implement bridge port vlan"). But ice_port_vlan_on() incorrectly assigns
ena_rx_filtering to inner_vlan_ops in DVM mode.
This causes an error when rx_filtering cannot be enabled in legacy mode.
Reproducer:
echo 1 > /sys/class/net/$PF/device/sriov_numvfs
ip link set $PF vf 0 spoofchk off trust on vlan 3
dmesg:
ice 0000:41:00.0: failed to enable Rx VLAN filtering for VF 0 VSI 9 during VF rebuild, error -95
Fixes: 2946204b3fa8 ("ice: implement bridge port vlan") Signed-off-by: Petr Oros <poros@redhat.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the very rare case where a packet type is unknown to the driver,
idpf_rx_process_skb_fields would return early without calling
eth_type_trans to set the skb protocol / the network layer handler.
This is especially problematic if tcpdump is running when such a
packet is received, i.e. it would cause a kernel panic.
Instead, call eth_type_trans for every single packet, even when
the packet type is unknown.
If packets are GROed with fraglist they might be segmented later on and
continue their journey in the stack. In skb_segment_list those skbs can
be reused as-is. This is an issue as their destructor was removed in
skb_gro_receive_list but not the reference to their socket, and then
they can't be orphaned. Fix this by also removing the reference to the
socket.
A similar construction is found in skb_gro_receive, apply the same
change there.
Fixes: 5e10da5385d2 ("skbuff: allow 'slow_gro' for skb carring sock reference") Signed-off-by: Antoine Tenart <atenart@kernel.org> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UDP tunnel packets can't be GRO in-between their endpoints as this
causes different issues. The UDP GRO fwd vxlan tests were relying on
this and their expectations have to be fixed.
We keep both vxlan tests and expected no GRO from happening. The vxlan
UDP GRO bench test was removed as it's not providing any valuable
information now.
Fixes: a062260a9d5f ("selftests: net: add UDP GRO forwarding self-tests") Signed-off-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In lan8814_get_sig_rx() and lan8814_get_sig_tx() ptp_parse_header() may
return NULL as ptp_header due to abnormal packet type or corrupted packet.
Fix this bug by adding ptp_header check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240329061631.33199-1-amishin@t-argos.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting mac_managed_pm during interface up is too late.
In situations where the link is not brought up yet and the system suspends
the regular PHY power management will run. Since the FEC ETHEREN control
bit is cleared (automatically) on suspend the controller is off in resume.
When the regular PHY power management resume path runs in this context it
will write to the MII_DATA register but nothing will be transmitted on the
MDIO bus.
The data written will however remain in the MII_DATA register.
When the link later is set to administrative up it will trigger a call to
fec_restart() which will restore the MII_SPEED register. This triggers the
quirk explained in f166f890c8f0 ("net: ethernet: fec: Replace interrupt
driven MDIO with polled IO") causing an extra MII_EVENT.
This extra event desynchronizes all the MDIO register reads, causing them
to complete too early. Leading all reads to read as 0 because
fec_enet_mdio_wait() returns too early.
When a Microchip LAN8700R PHY is connected to the FEC, the 0 reads causes
the PHY to be initialized incorrectly and the PHY will not transmit any
ethernet signal in this state. It cannot be brought out of this state
without a power cycle of the PHY.
There are 2 issues with the blamed commit.
1. When the phy is initialized, it would enable the disabled of UDPv4
checksums. The UDPv6 checksum is already enabled by default. So when
1-step is configured then it would clear these flags.
2. After the 1-step is configured, then if 2-step is configured then the
1-step would be still configured because it is not clearing the flag.
So the sync frames will still have origin timestamps set.
Fix this by reading first the value of the register and then
just change bit 12 as this one determines if the timestamp needs to
be inserted in the frame, without changing any other bits.
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Divya Koppera <divya.koppera@microchip.com> Link: https://lore.kernel.org/r/20240402071634.2483524-1-horatiu.vultur@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver should ensure that same priority is not mapped to multiple
rx queues. From DesignWare Cores Ethernet Quality-of-Service
Databook, section 17.1.29 MAC_RxQ_Ctrl2:
"[...]The software must ensure that the content of this field is
mutually exclusive to the PSRQ fields for other queues, that is,
the same priority is not mapped to multiple Rx queues[...]"
Previously rx_queue_priority() function was:
- clearing all priorities from a queue
- adding new priorities to that queue
After this patch it will:
- first assign new priorities to a queue
- then remove those priorities from all other queues
- keep other priorities previously assigned to that queue
Fixes: a8f5102af2a7 ("net: stmmac: TX and RX queue priority configuration") Fixes: 2142754f8b9c ("net: stmmac: Add MAC related callbacks for XGMAC2") Signed-off-by: Piotr Wejman <piotrwejman90@gmail.com> Link: https://lore.kernel.org/r/20240401192239.33942-1-piotrwejman90@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When zapping a table entry in stage2_try_break_pte(), we issue range
TLB invalidation for the region that was mapped by the table. However,
we neglect to align the base address down to the granule size and so
if we ended up reaching the table entry via a misaligned address then
we will accidentally skip invalidation for some prefix of the affected
address range.
Align 'ctx->addr' down to the granule size when performing TLB
invalidation for an unmapped table in stage2_try_break_pte().
Cc: Raghavendra Rao Ananta <rananta@google.com> Cc: Gavin Shan <gshan@redhat.com> Cc: Shaoqin Huang <shahuang@redhat.com> Cc: Quentin Perret <qperret@google.com> Fixes: defc8cc7abf0 ("KVM: arm64: Invalidate the table entries upon a range") Signed-off-by: Will Deacon <will@kernel.org> Reviewed-by: Shaoqin Huang <shahuang@redhat.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20240327124853.11206-5-will@kernel.org Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c910f2b65518 ("arm64/mm: Update tlb invalidation routines for
FEAT_LPA2") updated the __tlbi_level() macro to take the target level
as an argument, with TLBI_TTL_UNKNOWN (rather than 0) indicating that
the caller cannot provide level information. Unfortunately, the two
implementations of __kvm_tlb_flush_vmid_range() were not updated and so
now ask for an level 0 invalidation if FEAT_LPA2 is implemented.
Fix the problem by passing TLBI_TTL_UNKNOWN instead of 0 as the level
argument to __flush_s2_tlb_range_op() in __kvm_tlb_flush_vmid_range().
Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Oliver Upton <oliver.upton@linux.dev> Cc: Marc Zyngier <maz@kernel.org> Reviewed-by: Ryan Roberts <ryan.roberts@arm.com> Fixes: c910f2b65518 ("arm64/mm: Update tlb invalidation routines for FEAT_LPA2") Signed-off-by: Will Deacon <will@kernel.org> Reviewed-by: Shaoqin Huang <shahuang@redhat.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20240327124853.11206-4-will@kernel.org Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The srso_alias_untrain_ret() dummy thunk in the !CONFIG_MITIGATION_SRSO
case is there only for the altenative in CALL_UNTRAIN_RET to have
a symbol to resolve.
However, testing with kernels which don't have CONFIG_MITIGATION_SRSO
enabled, leads to the warning in patch_return() to fire:
missing return thunk: srso_alias_untrain_ret+0x0/0x10-0x0: eb 0e 66 66 2e
WARNING: CPU: 0 PID: 0 at arch/x86/kernel/alternative.c:826 apply_returns (arch/x86/kernel/alternative.c:826
Put in a plain "ret" there so that gcc doesn't put a return thunk in
in its place which special and gets checked.
syzkaller started using corpuses where a BPF tracing program deletes
elements from a sockmap/sockhash map. Because BPF tracing programs can be
invoked from any interrupt context, locks taken during a map_delete_elem
operation must be hardirq-safe. Otherwise a deadlock due to lock inversion
is possible, as reported by lockdep:
Locks in sockmap are hardirq-unsafe by design. We expects elements to be
deleted from sockmap/sockhash only in task (normal) context with interrupts
enabled, or in softirq context.
Detect when map_delete_elem operation is invoked from a context which is
_not_ hardirq-unsafe, that is interrupts are disabled, and bail out with an
error.
Note that map updates are not affected by this issue. BPF verifier does not
allow updating sockmap/sockhash from a BPF tracing program today.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Reported-by: xingwei lee <xrivendell7@gmail.com> Reported-by: yue sun <samsun1006219@gmail.com> Reported-by: syzbot+bc922f476bd65abbd466@syzkaller.appspotmail.com Reported-by: syzbot+d4066896495db380182e@syzkaller.appspotmail.com Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: syzbot+d4066896495db380182e@syzkaller.appspotmail.com Acked-by: John Fastabend <john.fastabend@gmail.com> Closes: https://syzkaller.appspot.com/bug?extid=d4066896495db380182e Closes: https://syzkaller.appspot.com/bug?extid=bc922f476bd65abbd466 Link: https://lore.kernel.org/bpf/20240402104621.1050319-1-jakub@cloudflare.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an load_nls_xxx() function fails a few lines above, the 'sbi->bdi_id' is
still 0.
So, in the error handling path, we will call ida_simple_remove(..., 0)
which is not allocated yet.
In order to prevent a spurious "ida_free called for id=0 which is not
allocated." message, tweak the error handling path and add a new label.
The buggy address belongs to the object at ffff88802cd73da0
which belongs to the cache kmalloc-8 of size 8
The buggy address is located 0 bytes inside of
allocated 1-byte region [ffff88802cd73da0, ffff88802cd73da1)
Memory state around the buggy address: ffff88802cd73c80: 07 fc fc fc 05 fc fc fc 05 fc fc fc fa fc fc fc ffff88802cd73d00: fa fc fc fc fa fc fc fc fa fc fc fc fa fc fc fc
>ffff88802cd73d80: fa fc fc fc 01 fc fc fc fa fc fc fc fa fc fc fc
^ ffff88802cd73e00: fa fc fc fc fa fc fc fc 05 fc fc fc 07 fc fc fc ffff88802cd73e80: 07 fc fc fc 07 fc fc fc 07 fc fc fc 07 fc fc fc
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org> Link: https://lore.kernel.org/r/20240404122051.2303764-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hook unregistration is deferred to the commit phase, same occurs with
hook updates triggered by the table dormant flag. When both commands are
combined, this results in deleting a basechain while leaving its hook
still registered in the core.
Fixes: 179d9ba5559a ("netfilter: nf_tables: fix table flag updates") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nft_unregister_flowtable_type() within nf_flow_inet_module_exit() can
concurrent with __nft_flowtable_type_get() within nf_tables_newflowtable().
And thhere is not any protection when iterate over nf_tables_flowtables
list in __nft_flowtable_type_get(). Therefore, there is pertential
data-race of nf_tables_flowtables list entry.
Use list_for_each_entry_rcu() to iterate over nf_tables_flowtables list
in __nft_flowtable_type_get(), and use rcu_read_lock() in the caller
nft_flowtable_type_get() to protect the entire type query process.
Similar to 2c9f0293280e ("netfilter: nf_tables: flush pending destroy
work before netlink notifier") to address a race between exit_net and
the destroy workqueue.
The trace below shows an element to be released via destroy workqueue
while exit_net path (triggered via module removal) has already released
the set that is used in such transaction.
Commit 82dfb540aeb2 ("VSOCK: Add virtio vsock vsockmon hooks") added
virtio_transport_deliver_tap_pkt() for handing packets to the
vsockmon device. However, in virtio_transport_send_pkt_work(),
the function is called before actually sending the packet (i.e.
before placing it in the virtqueue with virtqueue_add_sgs() and checking
whether it returned successfully).
Queuing the packet in the virtqueue can fail even multiple times.
However, in virtio_transport_deliver_tap_pkt() we deliver the packet
to the monitoring tap interface only the first time we call it.
This certainly avoids seeing the same packet replicated multiple times
in the monitoring interface, but it can show the packet sent with the
wrong timestamp or even before we succeed to queue it in the virtqueue.
Move virtio_transport_deliver_tap_pkt() after calling virtqueue_add_sgs()
and making sure it returned successfully.
Fixes: 82dfb540aeb2 ("VSOCK: Add virtio vsock vsockmon hooks") Cc: stable@vge.kernel.org Signed-off-by: Marco Pinna <marco.pinn95@gmail.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Link: https://lore.kernel.org/r/20240329161259.411751-1-marco.pinn95@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mana_get_rxbuf_cfg() aligns the RX buffer's DMA datasize to be
multiple of 64. So a packet slightly bigger than mtu+14, say 1536,
can be received and cause skb_over_panic.
As discussed internally, this alignment is not necessary. To fix
this bug, remove it from the code. So oversized packets will be
marked as CQE_RX_TRUNCATED by NIC, and dropped.
Cc: stable@vger.kernel.org Fixes: 2fbbd712baf1 ("net: mana: Enable RX path to handle various MTU sizes") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Dexuan Cui <decui@microsoft.com> Link: https://lore.kernel.org/r/1712087316-20886-1-git-send-email-haiyangz@microsoft.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the commit d2689b6a86b9 ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset is not executed from bind operation and
mac address is not read from the device registers or the devicetree at that
moment. Since the check to configure if the assigned mac address is random
or not for the interface, happens after the bind operation from
usbnet_probe, the interface keeps configured as random address, although the
address is correctly read and set during open operation (the only reset
now).
In order to keep only one reset for the device and to avoid the interface
always configured as random address, after reset, configure correctly the
suitable field from the driver, if the mac address is read successfully from
the device registers or the devicetree. Take into account if a locally
administered address (random) was previously stored.
cc: stable@vger.kernel.org # 6.6+ Fixes: d2689b6a86b9 ("net: usb: ax88179_178a: avoid two consecutive device resets") Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240403132158.344838-1-jtornosm@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* The code modified by this patch is guarded by IS_ERR(trans_private),
where trans_private is assigned as per the previous point in this analysis.
The only implementation of get_mr that I could locate is rds_ib_get_mr()
which can return an ERR_PTR if the conn (4th) argument is NULL.
* ret is set to PTR_ERR(trans_private).
rds_ib_get_mr can return ERR_PTR(-ENODEV) if the conn (4th) argument is NULL.
Thus ret may be -ENODEV in which case the code in question will execute.
Conclusion:
* cp may be NULL at the point where this patch adds a check;
this patch does seem to address a possible bug
Fixes: c055fc00c07b ("net/rds: fix WARNING in rds_conn_connect_if_down") Cc: stable@vger.kernel.org # v4.19+ Signed-off-by: Mahmoud Adam <mngyadam@amazon.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240326153132.55580-1-mngyadam@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Notice that skb_mark_for_recycle() is introduced later than fixes tag in
commit 6a5bcd84e886 ("page_pool: Allow drivers to hint on SKB recycling").
It is believed that fixes tag were missing a call to page_pool_release_page()
between v5.9 to v5.14, after which is should have used skb_mark_for_recycle().
Since v6.6 the call page_pool_release_page() were removed (in
commit 535b9c61bdef ("net: page_pool: hide page_pool_release_page()")
and remaining callers converted (in commit 6bfef2ec0172 ("Merge branch
'net-page_pool-remove-page_pool_release_page'")).
This leak became visible in v6.8 via commit dba1b8a7ab68 ("mm/page_pool: catch
page_pool memory leaks").
Cc: stable@vger.kernel.org Fixes: 6c5aa6fc4def ("xen networking: add basic XDP support for xen-netfront") Reported-by: Leonidas Spyropoulos <artafinde@archlinux.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=218654 Reported-by: Arthur Borsboom <arthurborsboom@gmail.com> Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org> Link: https://lore.kernel.org/r/171154167446.2671062.9127105384591237363.stgit@firesoul Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a bug in pm_nl_check_endpoint(), 'dev' didn't be parsed correctly.
If calling it in the 2nd test of endpoint_tests() too, it fails with an
error like this:
creation [FAIL] expected '10.0.2.2 id 2 subflow dev dev' \
found '10.0.2.2 id 2 subflow dev ns2eth2'
The reason is '$2' should be set to 'dev', not '$1'. This patch fixes it.
The commit mutex should not be released during the critical section
between nft_gc_seq_begin() and nft_gc_seq_end(), otherwise, async GC
worker could collect expired objects and get the released commit lock
within the same GC sequence.
nf_tables_module_autoload() temporarily releases the mutex to load
module dependencies, then it goes back to replay the transaction again.
Move it at the end of the abort phase after nft_gc_seq_end() is called.
Unlike early commit path stage which triggers a call to abort, an
explicit release of the batch is required on abort, otherwise mutex is
released and commit_list remains in place.
Add WARN_ON_ONCE to ensure commit_list is empty from the abort path
before releasing the mutex.
After this patch, commit_list is always assumed to be empty before
grabbing the mutex, therefore
03c1f1ef1584 ("netfilter: Cleanup nft_net->module_list from nf_tables_exit_net()")
only needs to release the pending modules for registration.
Cc: stable@vger.kernel.org Fixes: c0391b6ab810 ("netfilter: nf_tables: missing validation from the abort path") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct hci_dev members conn_info_max_age, conn_info_min_age,
le_conn_max_interval, le_conn_min_interval, le_adv_max_interval,
and le_adv_min_interval can be modified from the HCI core code, as well
through debugfs.
The debugfs implementation, that's only available to privileged users,
will check for boundaries, making sure that the minimum value being set
is strictly above the maximum value that already exists, and vice-versa.
However, as both minimum and maximum values can be changed concurrently
to us modifying them, we need to make sure that the value we check is
the value we end up using.
For example, with ->conn_info_max_age set to 10, conn_info_min_age_set()
gets called from vfs handlers to set conn_info_min_age to 8.
In conn_info_min_age_set(), this goes through:
if (val == 0 || val > hdev->conn_info_max_age)
return -EINVAL;
Concurrently, conn_info_max_age_set() gets called to set to set the
conn_info_max_age to 7:
if (val == 0 || val > hdev->conn_info_max_age)
return -EINVAL;
That check will also pass because we used the old value (10) for
conn_info_max_age.
After those checks that both passed, the struct hci_dev access
is mutex-locked, disabling concurrent access, but that does not matter
because the invalid value checks both passed, and we'll end up with
conn_info_min_age = 8 and conn_info_max_age = 7
To fix this problem, we need to lock the structure access before so the
check and assignment are not interrupted.
This fix was originally devised by the BassCheck[1] team, and
considered the problem to be an atomicity one. This isn't the case as
there aren't any concerns about the variable changing while we check it,
but rather after we check it parallel to another change.
This patch fixes CVE-2024-24858 and CVE-2024-24857.
We have a BT headset (Lenovo Thinkplus XT99), the pairing and
connecting has no problem, once this headset is paired, bluez will
remember this device and will auto re-connect it whenever the device
is powered on. The auto re-connecting works well with Windows and
Android, but with Linux, it always fails. Through debugging, we found
at the rfcomm connection stage, the bluetooth stack reports
"Connection refused - security block (0x0003)".
For this device, the re-connecting negotiation process is different
from other BT headsets, it sends the Link_KEY_REQUEST command before
the CONNECT_REQUEST completes, and it doesn't send ENCRYPT_CHANGE
command during the negotiation. When the device sends the "connect
complete" to hci, the ev->encr_mode is 1.
So here in the conn_complete_evt(), if ev->encr_mode is 1, link type
is ACL and HCI_CONN_ENCRYPT is not set, we set HCI_CONN_ENCRYPT to
this conn, and update conn->enc_key_size accordingly.
After this change, this BT headset could re-connect with Linux
successfully. This is the btmon log after applying the patch, after
receiving the "Connect Complete" with "Encryption: Enabled", will send
the command to read encryption key size:
> HCI Event: Connect Request (0x04) plen 10
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
Class: 0x240404
Major class: Audio/Video (headset, speaker, stereo, video, vcr)
Minor class: Wearable Headset Device
Rendering (Printing, Speaker)
Audio (Speaker, Microphone, Headset)
Link type: ACL (0x01)
...
> HCI Event: Link Key Request (0x17) plen 6
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
Link key: ${32-hex-digits-key}
...
> HCI Event: Connect Complete (0x03) plen 11
Status: Success (0x00)
Handle: 256
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
Link type: ACL (0x01)
Encryption: Enabled (0x01)
< HCI Command: Read Encryption Key... (0x05|0x0008) plen 2
Handle: 256
< ACL Data TX: Handle 256 flags 0x00 dlen 10
L2CAP: Information Request (0x0a) ident 1 len 2
Type: Extended features supported (0x0002)
> HCI Event: Command Complete (0x0e) plen 7
Read Encryption Key Size (0x05|0x0008) ncmd 1
Status: Success (0x00)
Handle: 256
Key size: 16
Cc: stable@vger.kernel.org Link: https://github.com/bluez/bluez/issues/704 Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Bluetooth controllers lack persistent storage for the device
address and instead one can be provided by the boot firmware using the
'local-bd-address' devicetree property.
The Bluetooth devicetree bindings clearly states that the address should
be specified in little-endian order, but due to a long-standing bug in
the Qualcomm driver which reversed the address some boot firmware has
been providing the address in big-endian order instead.
Add a new quirk that can be set on platforms with broken firmware and
use it to reverse the address when parsing the property so that the
underlying driver bug can be fixed.
Fixes: 5c0a1001c8be ("Bluetooth: hci_qca: Add helper to set device address") Cc: stable@vger.kernel.org # 5.1 Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WCN6855 firmware on the Lenovo ThinkPad X13s expects the Bluetooth
device address in big-endian order when setting it using the
EDL_WRITE_BD_ADDR_OPCODE command.
Presumably, this is the case for all non-ROME devices which all use the
EDL_WRITE_BD_ADDR_OPCODE command for this (unlike the ROME devices which
use a different command and expect the address in little-endian order).
Reverse the little-endian address before setting it to make sure that
the address can be configured using tools like btmgmt or using the
'local-bd-address' devicetree property.
Note that this can potentially break systems with boot firmware which
has started relying on the broken behaviour and is incorrectly passing
the address via devicetree in big-endian order.
The only device affected by this should be the WCN3991 used in some
Chromebooks. As ChromeOS updates the kernel and devicetree in lockstep,
the new 'qcom,local-bd-address-broken' property can be used to determine
if the firmware is buggy so that the underlying driver bug can be fixed
without breaking backwards compatibility.
Set the HCI_QUIRK_BDADDR_PROPERTY_BROKEN quirk for such platforms so
that the address is reversed when parsing the address property.
Fixes: 5c0a1001c8be ("Bluetooth: hci_qca: Add helper to set device address") Cc: stable@vger.kernel.org # 5.1 Cc: Balakrishna Godavarthi <quic_bgodavar@quicinc.com> Cc: Matthias Kaehlcke <mka@chromium.org> Tested-by: Nikita Travkin <nikita@trvn.ru> # sc7180 Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several Qualcomm Bluetooth controllers lack persistent storage for the
device address and instead one can be provided by the boot firmware
using the 'local-bd-address' devicetree property.
The Bluetooth bindings clearly states that the address should be
specified in little-endian order, but due to a long-standing bug in the
Qualcomm driver which reversed the address some boot firmware has been
providing the address in big-endian order instead.
The boot firmware in SC7180 Trogdor Chromebooks is known to be affected
so mark the 'local-bd-address' property as broken to maintain backwards
compatibility with older firmware when fixing the underlying driver bug.
Note that ChromeOS always updates the kernel and devicetree in lockstep
so that there is no need to handle backwards compatibility with older
devicetrees.
Fixes: 7ec3e67307f8 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt") Cc: stable@vger.kernel.org # 5.10 Cc: Rob Clark <robdclark@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Bjorn Andersson <andersson@kernel.org> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qualcomm Bluetooth controllers like WCN6855 do not have persistent
storage for the Bluetooth address and must therefore start as
unconfigured to allow the user to set a valid address unless one has
been provided by the boot firmware in the devicetree.
A recent change snuck into v6.8-rc7 and incorrectly started marking the
default (non-unique) address as valid. This specifically also breaks the
Bluetooth setup for some user of the Lenovo ThinkPad X13s.
Note that this is the second time Qualcomm breaks the driver this way
and that this was fixed last year by commit 6945795bc81a ("Bluetooth:
fix use-bdaddr-property quirk"), which also has some further details.
Fixes: 7dcd3e014aa7 ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT") Cc: stable@vger.kernel.org # 6.8 Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reported-by: Clayton Craft <clayton@craftyguy.net> Tested-by: Clayton Craft <clayton@craftyguy.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust the IP passed to `emit_patch` so it calculates the correct offset
for the CALL instruction if `x86_call_depth_emit_accounting` emits code.
Otherwise we will skip some instructions and most likely crash.
Add CPUID_LNX_5 to track cpufeatures' word 21, and add the appropriate
compile-time assert in KVM to prevent direct lookups on the features in
CPUID_LNX_5. KVM uses X86_FEATURE_* flags to manage guest CPUID, and so
must translate features that are scattered by Linux from the Linux-defined
bit to the hardware-defined bit, i.e. should never try to directly access
scattered features in guest CPUID.
Opportunistically add NR_CPUID_WORDS to enum cpuid_leafs, along with a
compile-time assert in KVM's CPUID infrastructure to ensure that future
additions update cpuid_leafs along with NCAPINTS.
No functional change intended.
Fixes: 7f274e609f3d ("x86/cpufeatures: Add new word for scattered features") Cc: Sandipan Das <sandipan.das@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
