This fixes a race which can result in the same virtual IRQ number
being assigned to two different MSI interrupts. The most visible
consequence of that is usually a warning and stack trace from the
sysfs code about an attempt to create a duplicate entry in sysfs.
The race happens when one CPU (say CPU 0) is disposing of an MSI
while another CPU (say CPU 1) is setting up an MSI. CPU 0 calls
(for example) pnv_teardown_msi_irqs(), which calls
msi_bitmap_free_hwirqs() to indicate that the MSI (i.e. its
hardware IRQ number) is no longer in use. Then, before CPU 0 gets
to calling irq_dispose_mapping() to free up the virtal IRQ number,
CPU 1 comes in and calls msi_bitmap_alloc_hwirqs() to allocate an
MSI, and gets the same hardware IRQ number that CPU 0 just freed.
CPU 1 then calls irq_create_mapping() to get a virtual IRQ number,
which sees that there is currently a mapping for that hardware IRQ
number and returns the corresponding virtual IRQ number (which is
the same virtual IRQ number that CPU 0 was using). CPU 0 then
calls irq_dispose_mapping() and frees that virtual IRQ number.
Now, if another CPU comes along and calls irq_create_mapping(), it
is likely to get the virtual IRQ number that was just freed,
resulting in the same virtual IRQ number apparently being used for
two different hardware interrupts.
To fix this race, we just move the call to msi_bitmap_free_hwirqs()
to after the call to irq_dispose_mapping(). Since virq_to_hw()
doesn't work for the virtual IRQ number after irq_dispose_mapping()
has been called, we need to call it before irq_dispose_mapping() and
remember the result for the msi_bitmap_free_hwirqs() call.
The pattern of calling msi_bitmap_free_hwirqs() before
irq_dispose_mapping() appears in 5 places under arch/powerpc, and
appears to have originated in commit 05af7bd2d75e ("[POWERPC] MPIC
U3/U4 MSI backend") from 2007.
Fixes: 05af7bd2d75e ("[POWERPC] MPIC U3/U4 MSI backend") Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In ext4_zero_range(), removing a file's entire block range from the
extent status tree removes all records of that file's delalloc extents.
The delalloc accounting code uses this information, and its loss can
then lead to accounting errors and kernel warnings at writeback time and
subsequent file system damage. This is most noticeable on bigalloc
file systems where code in ext4_ext_map_blocks() handles cases where
delalloc extents share clusters with a newly allocated extent.
Because we're not deleting a block range and are correctly updating the
status of its associated extent, there is no need to remove anything
from the extent status tree.
When this patch is combined with an unrelated bug fix for
ext4_zero_range(), kernel warnings and e2fsck errors reported during
xfstests runs on bigalloc filesystems are greatly reduced without
introducing regressions on other xfstests-bld test scenarios.
Signed-off-by: Eric Whitney <enwlinux@gmail.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit 0a196848ca36 ("perf: Fix arch_perf_out_copy_user default"),
changes copy_from_user_nmi() to return the number of
remaining bytes so that it behave like copy_from_user().
Unfortunately, when the range is outside of the process
memory, the return value is still the number of byte
copied, eg. 0, instead of the remaining bytes.
As all users of copy_from_user_nmi() were modified as
part of commit 0a196848ca36, the function should be
fixed to return the total number of bytes if range is
not correct.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1435001923-30986-1-git-send-email-ydroneaud@opteya.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Yann Droneaud <ydroneaud@opteya.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
'reshape_position' tracks where in the reshape we have reached.
'reshape_safe' tracks where in the reshape we have safely recorded
in the metadata.
These are compared to determine when to update the metadata.
So it is important that reshape_safe is initialised properly.
Currently it isn't. When starting a reshape from the beginning
it usually has the correct value by luck. But when reducing the
number of devices in a RAID10, it has the wrong value and this leads
to the metadata not being updated correctly.
This can lead to corruption if the reshape is not allowed to complete.
This patch is suitable for any -stable kernel which supports RAID10
reshape, which is 3.5 and later.
It looks like the Kconfig check that was meant to fix this (commit fe9233fb6914a0eb20166c967e3020f7f0fba2c9 [SCSI] scsi_dh: fix kconfig related
build errors) was actually reversed, but no-one noticed until the new set of
patches which separated DM and SCSI_DH).
Fixes: fe9233fb6914a0eb20166c967e3020f7f0fba2c9 Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When netlink mmap on receive side is the consumer of nf queue data,
it can happen that in some edge cases, we write skb shared info into
the user space mmap buffer:
Assume a possible rx ring frame size of only 4096, and the network skb,
which is being zero-copied into the netlink skb, contains page frags
with an overall skb->len larger than the linear part of the netlink
skb.
skb_zerocopy(), which is generic and thus not aware of the fact that
shared info cannot be accessed for such skbs then tries to write and
fill frags, thus leaking kernel data/pointers and in some corner cases
possibly writing out of bounds of the mmap area (when filling the
last slot in the ring buffer this way).
I.e. the ring buffer slot is then of status NL_MMAP_STATUS_VALID, has
an advertised length larger than 4096, where the linear part is visible
at the slot beginning, and the leaked sizeof(struct skb_shared_info)
has been written to the beginning of the next slot (also corrupting
the struct nl_mmap_hdr slot header incl. status etc), since skb->end
points to skb->data + ring->frame_size - NL_MMAP_HDRLEN.
The fix adds and lets __netlink_alloc_skb() take the actual needed
linear room for the network skb + meta data into account. It's completely
irrelevant for non-mmaped netlink sockets, but in case mmap sockets
are used, it can be decided whether the available skb_tailroom() is
really large enough for the buffer, or whether it needs to internally
fallback to a normal alloc_skb().
>From nf queue side, the information whether the destination port is
an mmap RX ring is not really available without extra port-to-socket
lookup, thus it can only be determined in lower layers i.e. when
__netlink_alloc_skb() is called that checks internally for this. I
chose to add the extra ldiff parameter as mmap will then still work:
We have data_len and hlen in nfqnl_build_packet_message(), data_len
is the full length (capped at queue->copy_range) for skb_zerocopy()
and hlen some possible part of data_len that needs to be copied; the
rem_len variable indicates the needed remaining linear mmap space.
The only other workaround in nf queue internally would be after
allocation time by f.e. cap'ing the data_len to the skb_tailroom()
iff we deal with an mmap skb, but that would 1) expose the fact that
we use a mmap skb to upper layers, and 2) trim the skb where we
otherwise could just have moved the full skb into the normal receive
queue.
After the patch, in my test case the ring slot doesn't fit and therefore
shows NL_MMAP_STATUS_COPY, where a full skb carries all the data and
thus needs to be picked up via recv().
Fixes: 3ab1f683bf8b ("nfnetlink: add support for memory mapped netlink") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
I've noticed that fixed_phy_register() ignores its 'irq' parameter instead of
passing it to fixed_phy_add(). Luckily, fixed_phy_register() seems to always
be called with PHY_POLL for 'irq'... :-)
Fixes: a75951217472 ("net: phy: extend fixed driver with fixed_phy_register()") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16:
- fixed_phy_add() only has 3 parameters in 3.16 kernel ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In commit f341861fb0b ("task_work: add a scheduling point in
task_work_run()") I fixed a latency problem adding a cond_resched()
call.
Later, commit ac3d0da8f329 added yet another loop to reverse a list,
bringing back the latency spike :
I've seen in some cases this loop taking 275 ms, if for example a
process with 2,000,000 files is killed.
We could add yet another cond_resched() in the reverse loop, or we
can simply remove the reversal, as I do not think anything
would depend on order of task_work_add() submitted works.
Fixes: ac3d0da8f329 ("task_work: Make task_work_add() lockless") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Maciej Żenczykowski <maze@google.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We previously register IPPROTO_ROUTING offload under inet6_add_offload(),
but in error path, we try to unregister it with inet_del_offload(). This
doesn't seem correct, it should actually be inet6_del_offload(), also
ipv6_exthdrs_offload_exit() from that commit seems rather incorrect (it
also uses rthdr_offload twice), but it got removed entirely later on.
Fixes: 3336288a9fea ("ipv6: Switch to using new offload infrastructure.") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The following panic is captured in ker3.14, but the issue still exists
in latest kernel.
---------------------------------------------------------------------
[ 20.738217] c0 3136 (Compiler) Unable to handle kernel NULL pointer dereference
at virtual address 00000578
......
[ 20.738499] c0 3136 (Compiler) PC is at _raw_spin_lock_irqsave+0x24/0x60
[ 20.738527] c0 3136 (Compiler) LR is at _raw_spin_lock_irqsave+0x20/0x60
[ 20.740134] c0 3136 (Compiler) Call trace:
[ 20.740165] c0 3136 (Compiler) [<ffffffc0008ee900>] _raw_spin_lock_irqsave+0x24/0x60
[ 20.740200] c0 3136 (Compiler) [<ffffffc0000dd024>] __wake_up+0x1c/0x54
[ 20.740230] c0 3136 (Compiler) [<ffffffc000639414>] mmc_wait_data_done+0x28/0x34
[ 20.740262] c0 3136 (Compiler) [<ffffffc0006391a0>] mmc_request_done+0xa4/0x220
[ 20.740314] c0 3136 (Compiler) [<ffffffc000656894>] sdhci_tasklet_finish+0xac/0x264
[ 20.740352] c0 3136 (Compiler) [<ffffffc0000a2b58>] tasklet_action+0xa0/0x158
[ 20.740382] c0 3136 (Compiler) [<ffffffc0000a2078>] __do_softirq+0x10c/0x2e4
[ 20.740411] c0 3136 (Compiler) [<ffffffc0000a24bc>] irq_exit+0x8c/0xc0
[ 20.740439] c0 3136 (Compiler) [<ffffffc00008489c>] handle_IRQ+0x48/0xac
[ 20.740469] c0 3136 (Compiler) [<ffffffc000081428>] gic_handle_irq+0x38/0x7c
----------------------------------------------------------------------
Because in SMP, "mrq" has race condition between below two paths:
path1: CPU0: <tasklet context>
static void mmc_wait_data_done(struct mmc_request *mrq)
{
mrq->host->context_info.is_done_rcv = true;
//
// If CPU0 has just finished "is_done_rcv = true" in path1, and at
// this moment, IRQ or ICache line missing happens in CPU0.
// What happens in CPU1 (path2)?
//
// If the mmcqd thread in CPU1(path2) hasn't entered to sleep mode:
// path2 would have chance to break from wait_event_interruptible
// in mmc_wait_for_data_req_done and continue to run for next
// mmc_request (mmc_blk_rw_rq_prep).
//
// Within mmc_blk_rq_prep, mrq is cleared to 0.
// If below line still gets host from "mrq" as the result of
// compiler, the panic happens as we traced.
wake_up_interruptible(&mrq->host->context_info.wait);
}
Fixes: 2a72f212263701b927559f6850446421d5906c41 ("IB/uverbs: Remove dev_table")
Before this commit there was a device look-up table that was protected
by a spin_lock used by ib_uverbs_open and by ib_uverbs_remove_one. When
it was dropped and container_of was used instead, it enabled the race
with remove_one as dev might be freed just after:
dev = container_of(inode->i_cdev, struct ib_uverbs_device, cdev) but
before the kref_get.
In addition, this buggy patch added some dead code as
container_of(x,y,z) can never be NULL and so dev can never be NULL.
As a result the comment above ib_uverbs_open saying "the open method
will either immediately run -ENXIO" is wrong as it can never happen.
The solution follows Jason Gunthorpe suggestion from below URL:
https://www.mail-archive.com/linux-rdma@vger.kernel.org/msg25692.html
cdev will hold a kref on the parent (the containing structure,
ib_uverbs_device) and only when that kref is released it is
guaranteed that open will never be called again.
In addition, fixes the active count scheme to use an atomic
not a kref to prevent WARN_ON as pointed by above comment
from Jason.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Shachar Raindel <raindel@mellanox.com> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The pkey mapping for RoCE must remain the default mapping:
VFs:
virtual index 0 = mapped to real index 0 (0xFFFF)
All others indices: mapped to a real pkey index containing an
invalid pkey.
PF:
virtual index i = real index i.
Don't allow users to change these mappings using files found in
sysfs.
Fixes: c1e7e466120b ('IB/mlx4: Add iov directory in sysfs under the ib device') Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
All the callers assume devm_spear_pcm_platform_register is a devm_ API, so
use devm_snd_dmaengine_pcm_register in devm_spear_pcm_platform_register.
Fixes: e1771bcf99b0 ("ASoC: SPEAr: remove custom DMA alloc compat function") Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
print_aggr() fails to print per-core/per-socket statistics after commit 582ec0829b3d ("perf stat: Fix per-socket output bug for uncore events")
if events have differnt cpus. Because in print_aggr(), aggr_get_id needs
index (not cpu id) to find core/pkg id. Also, evsel cpu maps should be
used to get aggregated id.
Here is an example:
Counting events cycles,uncore_imc_0/cas_count_read/. (Uncore event has
cpumask 0,18)
$ perf stat -e cycles,uncore_imc_0/cas_count_read/ -C0,18 --per-core sleep 2
Without this patch, it failes to get CPU 18 result.
commit bb8175a8aa42 ("mmc: sdhci: clarify DDR timing mode between
SD-UHS and eMMC") added MMC_DDR52 as eMMC's DDR mode to be
distinguished from SD-UHS, but it missed setting driver type for
MMC_DDR52 timing mode.
So sometimes we get the following error on Marvell BG2Q DMP board:
[ 1.559598] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd
response 0x900, card status 0xb00
[ 1.569314] mmcblk0: retrying using single block read
[ 1.575676] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd
response 0x900, card status 0x0
[ 1.585202] blk_update_request: I/O error, dev mmcblk0, sector 2
[ 1.591818] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd
response 0x900, card status 0x0
[ 1.601341] blk_update_request: I/O error, dev mmcblk0, sector 3
This patches fixes this by adding the missing driver type setting.
When keeping the configuration set by the bootloader (by using
the marvell,nand-keep-config property), the pxa3xx_nand_detect_config()
function is called and set the chunk size to 512 as a default value if
NDCR_PAGE_SZ is not set.
In the other case, when not keeping the bootloader configuration, no
chunk size is set. Fix this by adding a default chunk size of 512.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Acked-by: Robert Jarzmik <robert.jarzmik@free> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The powerpc kernel can be built to have either a 4K PAGE_SIZE or a 64K
PAGE_SIZE.
However when built with a 4K PAGE_SIZE there is an additional config
option which can be enabled, PPC_HAS_HASH_64K, which means the kernel
also knows how to hash a 64K page even though the base PAGE_SIZE is 4K.
This is used in one obscure configuration, to support 64K pages for SPU
local store on the Cell processor when the rest of the kernel is using
4K pages.
In this configuration, pte_pagesize_index() is defined to just pass
through its arguments to get_slice_psize(). However pte_pagesize_index()
is called for both user and kernel addresses, whereas get_slice_psize()
only knows how to handle user addresses.
This has been broken forever, however until recently it happened to
work. That was because in get_slice_psize() the large kernel address
would cause the right shift of the slice mask to return zero.
However in commit 7aa0727f3302 ("powerpc/mm: Increase the slice range to
64TB"), the get_slice_psize() code was changed so that instead of a
right shift we do an array lookup based on the address. When passed a
kernel address this means we index way off the end of the slice array
and return random junk.
That is only fatal if we happen to hit something non-zero, but when we
do return a non-zero value we confuse the MMU code and eventually cause
a check stop.
This fix is ugly, but simple. When we're called for a kernel address we
return 4K, which is always correct in this configuration, otherwise we
use the slice mask.
Fixes: 7aa0727f3302 ("powerpc/mm: Increase the slice range to 64TB") Reported-by: Cyril Bur <cyrilbur@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Sparse builds have been warning for a really long time now
that etherdevice.h has a conversion that is unsafe.
include/linux/etherdevice.h:79:32: warning: restricted __be16 degrades to integer
This code change fixes the issue and generates the exact
same assembly before/after (checked on x86_64)
Fixes: 2c722fe1c821 (etherdevice: Optimize a few is_<foo>_ether_addr functions) Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
So far the mcast tvlv handler did not anticipate the processing of
multiple incoming OGMs from the same originator at the same time. This
can lead to various issues:
* Broken refcounting: For instance two mcast handlers might both assume
that an originator just got multicast capabilities and will together
wrongly decrease mcast.num_disabled by two, potentially leading to
an integer underflow.
* Potential kernel panic on hlist_del_rcu(): Two mcast handlers might
one after another try to do an
hlist_del_rcu(&orig->mcast_want_all_*_node). The second one will
cause memory corruption / crashes.
(Reported by: Sven Eckelmann <sven@narfation.org>)
Right in the beginning the code path makes assumptions about the current
multicast related state of an originator and bases all updates on that. The
easiest and least error prune way to fix the issues in this case is to
serialize multiple mcast handler invocations with a spinlock.
Fixes: 60432d756cf0 ("batman-adv: Announce new capability via multicast TVLV") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: 60432d756cf0 ("batman-adv: Announce new capability via multicast TVLV") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
A miscounting of nodes having multicast optimizations enabled can lead
to multicast packet loss in the following scenario:
If the first OGM a node receives from another one has no multicast
optimizations support (no multicast tvlv) then we are missing to
increase the counter. This potentially leads to the wrong assumption
that we could safely use multicast optimizations.
Fixings this by increasing the counter if the initial OGM has the
multicast TVLV unset, too.
When purging an orig_node we should only decrease counter tracking the
number of nodes without multicast optimizations support if it was
increased through this orig_node before.
A not yet quite initialized orig_node (meaning it did not have its turn
in the mcast-tvlv handler so far) which gets purged would not adhere to
this and will lead to a counter imbalance.
Fixing this by adding a check whether the orig_node is mcast-initalized
before decreasing the counter in the mcast-orig_node-purging routine.
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: e17931d1a61d ("batman-adv: introduce capability initialization bitfield") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: 3f4841ffb336 ("batman-adv: tvlv - add network coding container") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: 17cf0ea455f1 ("batman-adv: tvlv - add distributed arp table container") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When we introduce a new sort key, we need to update the
hists__calc_col_len() function accordingly, otherwise the width
will be limited to strlen(header).
We can't update it when obtaining a line value for a column (for
instance, in sort__srcline_cmp()), because we reset it all when doing a
resort (see hists__output_recalc_col_len()), so we need to, from what is
in the hist_entry fields, set each of the column widths.
Cc: Namhyung Kim <namhyung@kernel.org> Cc: Andi Kleen <andi@firstfloor.org> Cc: Jiri Olsa <jolsa@kernel.org> Fixes: 409a8be61560 ("perf tools: Add sort by src line/number") Link: http://lkml.kernel.org/n/tip-jgbe0yx8v1gs89cslr93pvz2@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
wf_unregister_client() increments the client count when a client
unregisters. That is obviously incorrect. Decrement that client count
instead.
Fixes: 75722d3992f5 ("[PATCH] ppc64: Thermal control for SMU based machines") Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The EPOW interrupt handler uses rtas_get_sensor(), which in turn
uses rtas_busy_delay() to wait for RTAS becoming ready in case it
is necessary. But rtas_busy_delay() is annotated with might_sleep()
and thus may not be used by interrupts handlers like the EPOW handler!
This leads to the following BUG when CONFIG_DEBUG_ATOMIC_SLEEP is
enabled:
Fix this issue by introducing a new rtas_get_sensor_fast() function
that does not use rtas_busy_delay() - and thus can only be used for
sensors that do not cause a BUSY condition - known as "fast" sensors.
The EPOW sensor is defined to be "fast" in sPAPR - mpe.
Fixes: 587f83e8dd50 ("powerpc/pseries: Use rtas_get_sensor in RAS code") Signed-off-by: Thomas Huth <thuth@redhat.com> Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
bcmgenet_open()'s error path call free_irq() with a dev_id argument
different from the one we used to call request_irq() with, this will
make us trip over the warning in kernel/irq/manage.c:__free_irq()
Fixes: 1c1008c793fa4 ("net: bcmgenet: add main driver file") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The Linux NFS server returns garbage in the data payload of inline
NFS/RDMA READ replies. These are READs of under 1000 bytes or so
where the client has not provided either a reply chunk or a write
list.
The NFS server delivers the data payload for an NFS READ reply to
the transport in an xdr_buf page list. If the NFS client did not
provide a reply chunk or a write list, send_reply() is supposed to
set up a separate sge for the page containing the READ data, and
another sge for XDR padding if needed, then post all of the sges via
a single SEND Work Request.
The problem is send_reply() does not advance through the xdr_buf
when setting up scatter/gather entries for SEND WR. It always calls
dma_map_xdr with xdr_off set to zero. When there's more than one
sge, dma_map_xdr() sets up the SEND sge's so they all point to the
xdr_buf's head.
The current Linux NFS/RDMA client always provides a reply chunk or
a write list when performing an NFS READ over RDMA. Therefore, it
does not exercise this particular case. The Linux server has never
had to use more than one extra sge for building RPC/RDMA replies
with a Linux client.
However, an NFS/RDMA client _is_ allowed to send small NFS READs
without setting up a write list or reply chunk. The NFS READ reply
fits entirely within the inline reply buffer in this case. This is
perhaps a more efficient way of performing NFS READs that the Linux
NFS/RDMA client may some day adopt.
Fixes: b432e6b3d9c1 ('svcrdma: Change DMA mapping logic to . . .') BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=285 Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In fixup_ti816x_class(), we assigned "class = PCI_CLASS_MULTIMEDIA_VIDEO".
But PCI_CLASS_MULTIMEDIA_VIDEO is only the two-byte base class/sub-class
and needs to be shifted to make space for the low-order interface byte.
Shift PCI_CLASS_MULTIMEDIA_VIDEO to set the correct class code.
Fixes: 63c4408074cb ("PCI: Add quirk for setting valid class for TI816X Endpoint") Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Hemant Pedanekar <hemantp@ti.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Due to some recent changes in
drm_helper_probe_single_connector_modes_merge_bits(), old custom modes
were not being pruned properly. In current kernels,
drm_mode_validate_basic() is called to sanity-check each mode in the
list. If the sanity-check passes, the mode's status gets set to to
MODE_OK. In older kernels this check was not done, so old custom modes
would still have a status of MODE_UNVERIFIED at this point, and would
therefore be pruned later in the function.
As a result of this new behavior, the list of modes for a device always
includes every custom mode ever configured for the device, with the
largest one listed first. Since desktop environments usually choose the
first preferred mode when a hotplug event is emitted, this had the
result of making it very difficult for the user to reduce the size of
the display.
The qxl driver did implement the mode_valid connector function, but it
was empty. In order to restore the old behavior where old custom modes
are pruned, we implement a proper mode_valid function for the qxl
driver. This function now checks each mode against the last configured
custom mode and the list of standard modes. If the mode doesn't match
any of these, its status is set to MODE_BAD so that it will be pruned as
expected.
Signed-off-by: Jonathon Jongsma <jjongsma@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fix B-tree corruption when a new record is inserted at position 0 in the
node in hfs_brec_insert().
This is an identical change to the corresponding hfs b-tree code to Sergei
Antonov's "hfsplus: fix B-tree corruption after insertion at position 0",
to keep similar code paths in the hfs and hfsplus drivers in sync, where
appropriate.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Sergei Antonov <saproj@gmail.com> Cc: Joe Perches <joe@perches.com> Reviewed-by: Vyacheslav Dubeyko <slava@dubeyko.com> Cc: Anton Altaparmakov <anton@tuxera.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Pages looked up by __hfs_bnode_create() (called by hfs_bnode_create() and
hfs_bnode_find() for finding or creating pages corresponding to an inode)
are immediately kmap()'ed and used (both read and write) and kunmap()'ed,
and should not be page_cache_release()'ed until hfs_bnode_free().
This patch fixes a problem I first saw in July 2012: merely running "du"
on a large hfsplus-mounted directory a few times on a reasonably loaded
system would get the hfsplus driver all confused and complaining about
B-tree inconsistencies, and generates a "BUG: Bad page state". Most
recently, I can generate this problem on up-to-date Fedora 22 with shipped
kernel 4.0.5, by running "du /" (="/" + "/home" + "/mnt" + other smaller
mounts) and "du /mnt" simultaneously on two windows, where /mnt is a
lightly-used QEMU VM image of the full Mac OS X 10.9:
After applying the patch, I was able to run "du /" (60+ times) and "du
/mnt" (150+ times) continuously and simultaneously for 6+ hours.
There are many reports of the hfsplus driver getting confused under load
and generating "BUG: Bad page state" or other similar issues over the
years. [1]
The unpatched code [2] has always been wrong since it entered the kernel
tree. The only reason why it gets away with it is that the
kmap/memcpy/kunmap follow very quickly after the page_cache_release() so
the kernel has not had a chance to reuse the memory for something else,
most of the time.
The current RW driver appears to have followed the design and development
of the earlier read-only hfsplus driver [3], where-by version 0.1 (Dec
2001) had a B-tree node-centric approach to
read_cache_page()/page_cache_release() per bnode_get()/bnode_put(),
migrating towards version 0.2 (June 2002) of caching and releasing pages
per inode extents. When the current RW code first entered the kernel [2]
in 2005, there was an REF_PAGES conditional (and "//" commented out code)
to switch between B-node centric paging to inode-centric paging. There
was a mistake with the direction of one of the REF_PAGES conditionals in
__hfs_bnode_create(). In a subsequent "remove debug code" commit [4], the
read_cache_page()/page_cache_release() per bnode_get()/bnode_put() were
removed, but a page_cache_release() was mistakenly left in (propagating
the "REF_PAGES <-> !REF_PAGE" mistake), and the commented-out
page_cache_release() in bnode_release() (which should be spanned by
!REF_PAGES) was never enabled.
References:
[1]:
Michael Fox, Apr 2013
http://www.spinics.net/lists/linux-fsdevel/msg63807.html
("hfsplus volume suddenly inaccessable after 'hfs: recoff %d too large'")
Sasha Levin, Feb 2015
http://lkml.org/lkml/2015/2/20/85 ("use after free")
In I915_READ64_2x32 we attempt to read a 64bit register using 2 32bit
reads. Due to the nature of the registers we try to read in this manner,
they may increment between the two instruction (e.g. a timestamp
counter). To keep the result accurate, we repeat the read if we detect
an overflow (i.e. the upper value varies). However, some hardware is just
plain flaky and may endless loop as the the upper 32bits are not stable.
Just give up after a couple of tries and report whatever we read last.
v2: Use the most recent values when erring out on an unstable register.
Reported-by: russianneuromancer@ya.ru
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91906 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Michał Winiarski <michal.winiarski@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
reclaim_clean_pages_from_list() assumes that shrink_page_list() returns
number of pages removed from the candidate list. But shrink_page_list()
puts back mlocked pages without passing it to caller and without
counting as nr_reclaimed. This increases nr_isolated.
To fix this, this patch changes shrink_page_list() to pass unevictable
pages back to caller. Caller will take care those pages.
Minchan said:
It fixes two issues.
1. With unevictable page, cma_alloc will be successful.
Exactly speaking, cma_alloc of current kernel will fail due to
unevictable pages.
2. fix leaking of NR_ISOLATED counter of vmstat
With it, too_many_isolated works. Otherwise, it could make hang until
the process get SIGKILL.
Signed-off-by: Jaewon Kim <jaewon31.kim@samsung.com> Acked-by: Minchan Kim <minchan@kernel.org> Cc: Mel Gorman <mgorman@techsingularity.net> Acked-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The attached change fixes the condition used in the "sub" instruction.
A double word comparison is needed. This fixes the 64-bit LWS CAS
operation on 64-bit kernels.
I can now enable 64-bit atomic support in GCC.
Signed-off-by: John David Anglin <dave.anglin> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
b9d5c6b7ef57 ("[SCSI] cleanup setting task state in
scsi_error_handler()") has introduced a race between scsi_error_handler
and scsi_host_dev_release resulting in the hang when the device goes
away because scsi_error_handler might miss a wake up:
The most straightforward solution seems to be to invert the ordering of
the set_current_state and kthread_should_stop.
The issue has been noticed during reboot test on a 3.0 based kernel but
the current code seems to be affected in the same way.
[jejb: additional comment added] Reported-and-debugged-by: Mike Mayer <Mike.Meyer@teradata.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
According to datasheet, the S2MPS13X and S2MPS14X should update write
buffer via setting WUDR bit to high after ctrl register is written.
If not, ALARM interrupt of rtc-s5m doesn't happen first time when i use
tools/testing/selftests/timers/rtctest.c test program and hour format is
used to 12 hour mode in Odroid-XU3 board.
One more issue is the RTC doesn't keep time on Odroid-XU3 board when i
turn on board after power off even if RTC battery is connected. It can
be solved as setting WUDR & RUDR bits to high at the same time after
RTC_CTRL register is written. It's same with condition of only writing
ALARM registers, so this is for only S2MPS14 and we should set WUDR &
A_UDR bits to high on S2MPS13.
I can't find any reasonable description about this like fix from
datasheet, but can find similar codes from rtc driver source of
hardkernel kernel and vendor kernel.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
According to the bug report, FSC Amilo laptops with ALC880 can detect
the headphone jack but currently the driver disables it. It's partly
intentionally, as non-working jack detect was reported in the past.
Let's enable now.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102501 Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Many file systems that implement the show_options hook fail to correctly
escape their output which could lead to unescaped characters (e.g. new
lines) leaking into /proc/mounts and /proc/[pid]/mountinfo files. This
could lead to confusion, spoofed entries (resulting in things like
systemd issuing false d-bus "mount" notifications), and who knows what
else. This looks like it would only be the root user stepping on
themselves, but it's possible weird things could happen in containers or
in other situations with delegated mount privileges.
Here's an example using overlay with setuid fusermount trusting the
contents of /proc/mounts (via the /etc/mtab symlink). Imagine the use
of "sudo" is something more sneaky:
This fixes the problem by adding new seq_show_option and
seq_show_option_n helpers, and updating the vulnerable show_option
handlers to use them as needed. Some, like SELinux, need to be open
coded due to unusual existing escape mechanisms.
[akpm@linux-foundation.org: add lost chunk, per Kees]
[keescook@chromium.org: seq_show_option should be using const parameters] Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Serge Hallyn <serge.hallyn@canonical.com> Acked-by: Jan Kara <jack@suse.com> Acked-by: Paul Moore <paul@paul-moore.com> Cc: J. R. Okajima <hooanon05g@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ luis: backported to 3.16:
- dropped changes to fs/overlayfs/super.c, net/ceph/ceph_common.c and to
cgroup_show_options() in kernel/cgroup.c
- adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The system has non continuous RAM address:
BIOS-e820: [mem 0x0000001300000000-0x0000001cffffffff] usable
BIOS-e820: [mem 0x0000001d70000000-0x0000001ec7ffefff] usable
BIOS-e820: [mem 0x0000001f00000000-0x0000002bffffffff] usable
BIOS-e820: [mem 0x0000002c18000000-0x0000002d6fffefff] usable
BIOS-e820: [mem 0x0000002e00000000-0x00000039ffffffff] usable
So there are start sections in memory block not present. For example:
memory block : [0x2c18000000, 0x2c20000000) 512M
first three sections are not present.
The current register_mem_sect_under_node() assume first section is
present, but memory block section number range [start_section_nr,
end_section_nr] would include not present section.
For arch that support vmemmap, we don't setup memmap for struct page
area within not present sections area.
So skip the pfn range that belong to absent section.
[akpm@linux-foundation.org: simplification]
[rientjes@google.com: more simplification] Fixes: bdee237c0343 ("x86: mm: Use 2GB memory block size on large memory x86-64 systems") Fixes: 982792c782ef ("x86, mm: probe memory block size for generic x86 64bit") Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: David Rientjes <rientjes@google.com> Reported-by: Tony Luck <tony.luck@intel.com> Tested-by: Tony Luck <tony.luck@intel.com> Cc: Greg KH <greg@kroah.com> Cc: Ingo Molnar <mingo@elte.hu> Tested-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Currently context size (cra_ctxsize) doesn't specified for
ghash_async_alg. Which means it's zero. Thus crypto_create_tfm()
doesn't allocate needed space for ghash_async_ctx, so any
read/write to ctx (e.g. in ghash_async_init_tfm()) is not valid.
Signed-off-by: Andrey Ryabinin <aryabinin@odin.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We've got bug reports showing the old systemd-logind (at least
system-210) aborting unexpectedly, and this turned out to be because
of an invalid error code from close() call to evdev devices. close()
is supposed to return only either EINTR or EBADFD, while the device
returned ENODEV. logind was overreacting to it and decided to kill
itself when an unexpected error code was received. What a tragedy.
The bad error code comes from flush fops, and actually evdev_flush()
returns ENODEV when device is disconnected or client's access to it is
revoked. But in these cases the fact that flush did not actually happen is
not an error, but rather normal behavior. For non-disconnected devices
result of flush is also not that interesting as there is no potential of
data loss and even if it fails application has no way of handling the
error. Because of that we are better off always returning success from
evdev_flush().
Also returning EINTR from flush()/close() is discouraged (as it is not
clear how application should handle this error), so let's stop taking
evdev->mutex interruptibly.
We have many WR opcodes that are only supported in kernel space
and/or require optional information to be copied into the WR
structure. Reject all those not explicitly handled so that we
can't pass invalid information to drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
With the radeon driver loaded the HP Compaq dc5750
Small Form Factor machine fails to resume from suspend.
Adding a quirk similar to other devices avoids
the problem and the system resumes properly.
Signed-off-by: Jeffery Miller <jmiller@neverware.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
There have been many hard to track down bugs whereby userspace forgot to
flag a write buffer and then cause graphics corruption or a hung GPU
when that buffer was later purged under memory pressure (as the buffer
appeared clean, its pages would have been evicted rather than preserved
and any changes more recent than in the backing storage would be lost).
In retrospect this is a rare optimisation against memory pressure,
already the slow path. If we always mark the buffer as dirty when
accessed by the GPU, anything not used can still be evicted cheaply
(ideal behaviour for mark-and-sweep eviction) but we do not run the risk
of corruption. For correct read serialisation, userspace still has to
notify when the GPU writes to an object. However, there are certain
situations under which userspace may wish to tell white lies to the
kernel...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Kristian Høgsberg <krh@bitplanet.net> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: "Goel, Akash" <akash.goel@intel.co> Cc: Michał Winiarski <michal.winiarski@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The temperature registers appear to report values in degrees Celsius
while the hwmon API mandates values to be exposed in millidegrees
Celsius. Do the conversion so that the values reported by "sensors"
are correct.
Fixes: aed93e0bf493 ("tg3: Add hwmon support for temperature") Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Prashant Sreedharan <prashant@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
AUX addresses are 20 bits long. Send out the entire address instead of
just the low 16 bits.
Cc: Alex Deucher <alexander.deucher@amd.com> Cc: "Christian König" <christian.koenig@amd.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The lkey table is allocated with with a get_user_pages() with an
order based on a number of index bits from a module parameter.
The underlying kernel code cannot allocate that many contiguous pages.
There is no reason the underlying memory needs to be physically
contiguous.
This patch:
- switches the allocation/deallocation to vmalloc/vfree
- caps the number of bits to 23 to insure at least 1 generation bit
o this matches the module parameter description
Reviewed-by: Vinit Agnihotri <vinit.abhay.agnihotri@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
There is an issue with xfs's error reporting in some cases of I/O partially
failing and partially succeeding. Calls like fsync() can report success even
though not all I/O was successful in partial-failure cases such as one disk of
a RAID0 array being offline.
The issue can occur when there are more than one bio per xfs_ioend struct.
Each call to xfs_end_bio() for a bio completing will write a value to
ioend->io_error. If a successful bio completes after any failed bio, no
error is reported do to it writing 0 over the error code set by any failed bio.
The I/O error information is now lost and when the ioend is completed
only success is reported back up the filesystem stack.
xfs_end_bio() should only set ioend->io_error in the case of BIO_UPTODATE
being clear. ioend->io_error is initialized to 0 at allocation so only needs
to be updated by a failed bio. Also check that ioend->io_error is 0 so that
the first error reported will be the error code returned.
Signed-off-by: David Jeffery <djeffery@redhat.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When a task calls execve(), its FP/SIMD state is flushed so that
none of the original program state is observeable by the incoming
program.
However, since this flushing consists of setting the in-memory copy
of the FP/SIMD state to all zeroes, the CPU field is set to CPU 0 as
well, which indicates to the lazy FP/SIMD preserve/restore code that
the FP/SIMD state does not need to be reread from memory if the task
is scheduled again on CPU 0 without any other tasks having entered
userland (or used the FP/SIMD in kernel mode) on the same CPU in the
mean time. If this happens, the FP/SIMD state of the old program will
still be present in the registers when the new program starts.
So set the CPU field to the invalid value of NR_CPUS when performing
the flush, by calling fpsimd_flush_task_state().
Reported-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com> Reported-by: Janet Liu <janet.liu@spreadtrum.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The unregister path of platform_device is broken. On registration, it
will register all resources with either a parent already set, or
type==IORESOURCE_{IO,MEM}. However, on unregister it will release
everything with type==IORESOURCE_{IO,MEM}, but ignore the others. There
are also cases where resources don't get registered in the first place,
like with devices created by of_platform_populate()*.
Fix the unregister path to be symmetrical with the register path by
checking the parent pointer instead of the type field to decide which
resources to unregister. This is safe because the upshot of the
registration path algorithm is that registered resources have a parent
pointer, and non-registered resources do not.
* It can be argued that of_platform_populate() should be registering
it's resources, and they argument has some merit. However, there are
quite a few platforms that end up broken if we try to do that due to
overlapping resources in the device tree. Until that is fixed, we need
to solve the immediate problem.
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: Rob Herring <robh@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Grant Likely <grant.likely@linaro.org> Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If the internal call to of_address_to_resource() fails, we end up
looping forever in of_find_matching_node_by_address(). This can be
caused by a defective device tree, or calling with an incorrect
matches argument.
Fix by calling of_find_matching_node() unconditionally at the end of
the loop.
Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The v2 of NetGear WNA1000M uses a different idProduct: USB ID 0846:9043
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
During the various CPU_ONLINE callbacks CPUn is online but not
active. Several things can go wrong at that point, depending on
the scheduling of tasks on CPU0.
The ->wake_cpu of the unparked thread is not allowed, making a call
to select_fallback_rq() necessary. Then, select_fallback_rq() cannot
find an allowed, active CPU and promptly resets the allowed CPUs, so
that the task in question ends up on CPU0.
When those unparked tasks are eventually executed, they run
immediately into a BUG:
kernel BUG at kernel/smpboot.c:135!
Just changing the order in which the online/active bits are set
(and adding some memory barriers), would solve the two issues
above. However, it would change the order of operations back to
the one before commit 6acbfb96976f ("sched: Fix hotplug vs.
set_cpus_allowed_ptr()"), thus, reintroducing that particular
problem.
Going further back into history, we have at least the following
commits touching this topic:
- commit 2baab4e90495 ("sched: Fix select_fallback_rq() vs cpu_active/cpu_online")
- commit 5fbd036b552f ("sched: Cleanup cpu_active madness")
Together, these give us the following non-working solutions:
- secondary CPU sets active before online, because active is assumed to
be a subset of online;
- secondary CPU sets online before active, because the primary CPU
assumes that an online CPU is also active;
- secondary CPU sets online and waits for primary CPU to set active,
because it might deadlock.
Commit 875ebe940d77 ("powerpc/smp: Wait until secondaries are
active & online") introduces an arch-specific solution to this
arch-independent problem.
Now, go for a more general solution without explicit waiting and
simply set active twice: once on the secondary CPU after online
was set and once on the primary CPU after online was seen.
set_cpus_allowed_ptr()")
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Anton Blanchard <anton@samba.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Joerg Roedel <jroedel@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Wilson <msw@amazon.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 6acbfb96976f ("sched: Fix hotplug vs. set_cpus_allowed_ptr()") Link: http://lkml.kernel.org/r/1439408156-18840-1-git-send-email-jschoenh@amazon.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Users have occasionally reported that file type for some directory
entries is wrong. This mostly happened after updating libraries some
libraries. After some debugging the problem was traced down to
xfs_dir2_node_replace(). The function uses args->filetype as a file type
to store in the replaced directory entry however it also calls
xfs_da3_node_lookup_int() which will store file type of the current
directory entry in args->filetype. Thus we fail to change file type of a
directory entry to a proper type.
Fix the problem by storing new file type in a local variable before
calling xfs_da3_node_lookup_int().
Reported-by: Giacomo Comes <comes@naic.edu> Signed-off-by: Jan Kara <jack@suse.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
[ luis: backported to 3.16:
- file rename: fs/xfs/libxfs/xfs_dir2_node.c -> fs/xfs/xfs_dir2_node.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Most of the time this isn't an issue since hotplugging an adaptor will
trigger a crtc mode change which in turn, causes the driver to probe
every DisplayPort for a dpcd. However, in cases where hotplugging
doesn't cause a mode change (specifically when one unplugs a monitor
from a DisplayPort connector, then plugs that same monitor back in
seconds later on the same port without any other monitors connected), we
never probe for the dpcd before starting the initial link training. What
happens from there looks like this:
- GPU has only one monitor connected. It's connected via
DisplayPort, and does not go through an adaptor of any sort.
- User unplugs DisplayPort connector from GPU.
- Change in HPD is detected by the driver, we probe every
DisplayPort for a possible connection.
- Probe the port the user originally had the monitor connected
on for it's dpcd. This fails, and we clear the first (and only
the first) byte of the dpcd to indicate we no longer have a
dpcd for this port.
- User plugs the previously disconnected monitor back into the
same DisplayPort.
- radeon_connector_hotplug() is called before everyone else,
and tries to handle the link training. Since only the first
byte of the dpcd is zeroed, the driver is able to complete
link training but does so against the wrong dpcd, causing it
to initialize the link with the wrong settings.
- Display stays blank (usually), dpcd is probed after the
initial link training, and the driver prints no obvious
messages to the log.
In theory, since only one byte of the dpcd is chopped off (specifically,
the byte that contains the revision information for DisplayPort), it's
not entirely impossible that this bug may not show on certain monitors.
For instance, the only reason this bug was visible on my ASUS PB238
monitor was due to the fact that this monitor using the enhanced framing
symbol sequence, the flag for which is ignored if the radeon driver
thinks that the DisplayPort version is below 1.1.
Signed-off-by: Stephen Chandler Paul <cpaul@redhat.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Since v3.18, attempts to deliver IRQ0 are rejected, breaking orion5x.
Fix this by increasing all interrupts by one, as did 5d6bed2a9c8b for
dove. Also, force MULTI_IRQ_HANDLER for all orion platforms (including
dove) as the specific handler is needed to shift back IRQ numbers by
one.
[gregory.clement@free-electrons.com]: moved the select
MULTI_IRQ_HANDLER from PLAT_ORION_LEGACY to ARCH_ORION5X as it broke
the build for dove.
Fixes: a71b092a9c68 ("ARM: Convert handle_IRQ to use __handle_domain_irq") Signed-off-by: Benjamin Cama <benoar@dolka.fr> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by: Detlef Vollmann <dv@vollmann.ch> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
While we are committing a transaction, it's possible the previous one is
still finishing its commit and therefore we wait for it to finish first.
However we were not checking if that previous transaction ended up getting
aborted after we waited for it to commit, so we ended up committing the
current transaction which can lead to fs corruption because the new
superblock can point to trees that have had one or more nodes/leafs that
were never durably persisted.
The following sequence diagram exemplifies how this is possible:
btrfs_write_and_wait_transaction() continues
writing ebs
--> fails writing eb X, we abort transaction N
and set bit BTRFS_FS_STATE_ERROR on
fs_info->fs_state, so no new transactions
can start after setting that bit
cleanup_transaction()
btrfs_cleanup_one_transaction()
wakes up task at CPU 1
continues, doesn't abort because
cur_trans->aborted (transaction N + 1)
is zero, and no checks for bit
BTRFS_FS_STATE_ERROR in fs_info->fs_state
are made
btrfs_write_and_wait_transaction(trans, root);
--> succeeds, no errors during writeback
write_ctree_super(trans, root, 0);
--> succeeds
--> we have now a superblock that points us
to some root that uses eb X, which was
never written to disk
In this scenario future attempts to read eb X from disk results in an
error message like "parent transid verify failed on X wanted Y found Z".
So fix this by aborting the current transaction if after waiting for the
previous transaction we verify that it was aborted.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
struct xfs_attr_leafblock contains 'entries' array which is declared
with size 1 altough it can in fact contain much more entries. Since this
array is followed by further struct members, gcc (at least in version
4.8.3) thinks that the array has the fixed size of 1 element and thus
may optimize away all accesses beyond the end of array resulting in
non-working code. This problem was only observed with userspace code in
xfsprogs, however it's better to be safe in kernel as well and have
matching kernel and xfsprogs definitions.
Signed-off-by: Jan Kara <jack@suse.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
[ luis: backported to 3.16:
- file rename: fs/xfs/libxfs/xfs_da_format.h -> fs/xfs/xfs_da_format.h ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In the dir3 data block readahead function, use the regular read
verifier to check the block's CRC and spot-check the block contents
instead of directly calling only the spot-checking routine. This
prevents corrupted directory data blocks from being read into the
kernel, which can lead to garbage ls output and directory loops (if
say one of the entries contains slashes and other junk).
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
[ luis: backported to 3.16:
- file rename: fs/xfs/libxfs/xfs_dir2_data.c -> fs/xfs/xfs_dir2_data.c
- adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Consider eCryptfs dcache entries to be stale when the corresponding
lower inode's i_nlink count is zero. This solves a problem caused by the
lower inode being directly modified, without going through the eCryptfs
mount, leaving stale eCryptfs dentries cached and the eCryptfs inode's
i_nlink count not being cleared.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Reported-by: Richard Weinberger <richard@nod.at>
[ luis: backported to 3.16:
- use dentry->d_inode instead of d_inode(dentry)
- adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
It was reported that after 10-20 reboots, a usb keyboard plugged
into a docking station would not work unless it was replugged in.
Using usbmon, it turns out the interrupt URBs were streaming with
callback errors of -71 for some reason. The hid-core.c::hid_io_error was
supposed to retry and then reset, but the reset wasn't really happening.
The check for HID_NO_BANDWIDTH was inverted. Fix was simple.
Tested by reporter and locally by me by unplugging a keyboard halfway until I
could recreate a stream of errors but no disconnect.
Signed-off-by: Don Zickus <dzickus@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When initializing igb driver (e.g. 82576, I350), IGB_FLAG_QUEUE_PAIRS is
set if adapter->rss_queues exceeds half of max_rss_queues in
igb_init_queue_configuration().
On the other hand, IGB_FLAG_QUEUE_PAIRS is not set even if the number of
queues exceeds half of max_combined in igb_set_channels() when changing
the number of queues by "ethtool -L".
In this case, if numvecs is larger than MAX_MSIX_ENTRIES (10), the size
of adapter->msix_entries[], an overflow can occur in
igb_set_interrupt_capability(), which in turn leads to an oops.
Fix this problem as follows:
- When changing the number of queues by "ethtool -L", set
IGB_FLAG_QUEUE_PAIRS in the same way as initializing igb driver.
- When increasing the size of q_vector, reallocate it appropriately.
(With IGB_FLAG_QUEUE_PAIRS set, the size of q_vector gets larger.)
Another possible way to fix this problem is to cap the queues at its
initial number, which is the number of the initial online cpus. But this
is not the optimal way because we cannot increase queues when another
cpu becomes online.
Note that before commit cd14ef54d25b ("igb: Change to use statically
allocated array for MSIx entries"), this problem did not cause oops
but just made the number of queues become 1 because of entering msi_only
mode in igb_set_interrupt_capability().
Fixes: 907b7835799f ("igb: Add ethtool support to configure number of channels") Signed-off-by: Shota Suzuki <suzuki_shota_t3@lab.ntt.co.jp> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The driver used usb_get_serial_data(port->serial) which compiled but resulted
in a NULL pointer being returned (and subsequently used). I did not go deeper
into this but I guess this is a regression.
Signed-off-by: Philipp Hachtmann <hachti@hachti.de> Fixes: a85796ee5149 ("USB: symbolserial: move private-data allocation to
port_probe") Acked-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We should ensure that we always set the pgio_header's error field
if a READ or WRITE RPC call returns an error. The current code depends
on 'hdr->good_bytes' always being initialised to a large value, which
is not always done correctly by callers.
When this happens, applications may end up missing important errors.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
call12 can't be safely used as the first call in the inline function,
because the compiler does not extend the stack frame of the bounding
function accordingly, which may result in corruption of local variables.
If a call needs to be done, do call8 first followed by call12.
For pure assembly code in _switch_to increase stack frame size of the
bounding function.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
There may be lots of pending requests so that the buffer of PAGE_SIZE
can't hold them at all.
One typical example is scsi-mq, the queue depth(.can_queue) of
scsi_host and blk-mq is quite big but scsi_device's queue_depth
is a bit small(.cmd_per_lun), then it is quite easy to have lots
of pending requests in hw queue.
This patch fixes the following warning and the related memory
destruction.
The "adl_pci7x3x" driver replaced the "adl_pci7230" and "adl_pci7432"
drivers in commits 8f567c373c4b ("staging: comedi: new adl_pci7x3x
driver") and 657f77d173d3 ("staging: comedi: remove adl_pci7230 and
adl_pci7432 drivers"). Although the new driver code agrees with the
user manuals for the respective boards, digital outputs stopped working
on the PCI-7230. This has 16 digital output channels and the previous
adl_pci7230 driver shifted the 16 bit output state left by 16 bits
before writing to the hardware register. The new adl_pci7x3x driver
doesn't do that. Fix it in `adl_pci7x3x_do_insn_bits()` by checking
for the special case of the subdevice having only 16 channels and
duplicating the 16 bit output state into both halves of the 32-bit
register. That should work both for what the board actually does and
for what the user manual says it should do.
Fixes: 8f567c373c4b ("staging: comedi: new adl_pci7x3x driver") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This way this device can be used with irtty-sir -
at least on Toshiba Satellite A20-S103 it is not configured by default
and needs PNP activation before it starts to respond on I/O ports.
This device has actually its own driver (ali-ircc),
but this driver seems to be non-functional for a very long time
(see http://permalink.gmane.org/gmane.linux.irda.general/484
http://permalink.gmane.org/gmane.network.protocols.obex.openobex.user/943
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=535070 ).
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
regulator_disable of pbias always writes '0' to the enable_reg.
However actual disable value of pbias regulator is not always '0'.
Fix it by populating the disable_val in pbias_reg_info for the
various platforms and assign it to the disable_val of
pbias regulator descriptor. This will be used by
regulator_disable_regmap while disabling pbias regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Don't set .read_flag_mask for adav803, it's for adav801 only.
Fixes: 0c2d69645628 ("ASoC: adav80x: Split SPI and I2C code into different modules") Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Before the make_empty_dir_inode calls were introduce into proc, sysfs,
and sysctl those directories when stated reported an i_size of 0.
make_empty_dir_inode started reporting an i_size of 2. At least one
userspace application depended on stat returning i_size of 0. So
modify make_empty_dir_inode to cause an i_size of 0 to be reported for
these directories.
Reported-by: Tejun Heo <tj@kernel.org> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In the logic in the initial commit of unshare made creating a new
thread group for a process, contingent upon creating a new memory
address space for that process. That is wrong. Two separate
processes in different thread groups can share a memory address space
and clone allows creation of such proceses.
This is significant because it was observed that mm_users > 1 does not
mean that a process is multi-threaded, as reading /proc/PID/maps
temporarily increments mm_users, which allows other processes to
(accidentally) interfere with unshare() calls.
Correct the check in check_unshare_flags() to test for
!thread_group_empty() for CLONE_THREAD, CLONE_SIGHAND, and CLONE_VM.
For sighand->count > 1 for CLONE_SIGHAND and CLONE_VM.
For !current_is_single_threaded instead of mm_users > 1 for CLONE_VM.
By using the correct checks in unshare this removes the possibility of
an accidental denial of service attack.
Additionally using the correct checks in unshare ensures that only an
explicit unshare(CLONE_VM) can possibly trigger the slow path of
current_is_single_threaded(). As an explict unshare(CLONE_VM) is
pointless it is not expected there are many applications that make
that call.
Fixes: b2e0d98705e60e45bbb3c0032c48824ad7ae0704 userns: Implement unshare of the user namespace Reported-by: Ricky Zhou <rickyz@chromium.org> Reported-by: Kees Cook <keescook@chromium.org> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
NFSv4 takes O_EXCL as a sign that a setattr command should be sent,
probably to reset the timestamps.
When it was an O_RDONLY open, the SETATTR command does not
identify any actual attributes to change.
If no delegation was provided to the open, the SETATTR uses the
all-zeros stateid and the request is accepted (at least by the
Linux NFS server - no harm, no foul).
If a read-delegation was provided, this is used in the SETATTR
request, and a Netapp filer will justifiably claim
NFS4ERR_BAD_STATEID, which the Linux client takes as a sign
to retry - indefinitely.
So only treat O_EXCL specially if O_CREAT was also given.
Negative return values are not supported by iio_event_poll since
its return type is unsigned int.
Fixes: f18e7a068a0a3 ("iio: Return -ENODEV for file operations if the device has been unregistered") Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The power for line out was not turned on when line out is enabled.
So we add "LOUT amp" widget to turn on the power for line out.
Signed-off-by: John Lin <john.lin@realtek.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Like some of the other Yoga models the Lenovo Yoga 3 14 does not have a
hw rfkill switch, and trying to read the hw rfkill switch through the
ideapad module causes it to always reported blocking breaking wifi.
This commit adds the Lenovo Yoga 3 14 to the no_hw_rfkill dmi list, fixing
the wifi breakage.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1239050 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
projects / thirdparty / kernel / stable.git / log
