Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
at91rm9200 standby and suspend to ram has been broken since 00482a4078f4. It is wrongly using AT91_BASE_SYS which is a physical address
and actually doesn't correspond to any register on at91rm9200.
Use the correct at91_ramc_base[0] instead.
Fixes: 00482a4078f4 (ARM: at91: implement the standby function for pm/cpuidle) Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The current HDA generic parser initializes / modifies the amp values
always in stereo, but this seems causing the problem on ALC3229 codec
that has a few mono channel widgets: namely, these mono widgets react
to actions for both channels equally.
In the driver code, we do care the mono channel and create a control
only for the left channel (as defined in HD-audio spec) for such a
node. When the control is updated, only the left channel value is
changed. However, in the resume, the right channel value is also
restored from the initial value we took as stereo, and this overwrites
the left channel value. This ends up being the silent output as the
right channel has been never touched and remains muted.
This patch covers the places where unconditional stereo amp accesses
are done and converts to the conditional accesses.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94581 Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
According to a report from Yuxuan Shui, nilfs2 in kernel 3.19 got stuck
during recovery at mount time. The code path that caused the deadlock was
as follows:
nilfs_fill_super()
load_nilfs()
nilfs_salvage_orphan_logs()
* Do roll-forwarding, attach segment constructor for recovery,
and kick it.
nilfs_segctor_thread()
nilfs_segctor_thread_construct()
* A lock is held with nilfs_transaction_lock()
nilfs_segctor_do_construct()
nilfs_segctor_drop_written_files()
iput()
iput_final()
write_inode_now()
writeback_single_inode()
__writeback_single_inode()
do_writepages()
nilfs_writepage()
nilfs_construct_dsync_segment()
nilfs_transaction_lock() --> deadlock
This can happen if commit 7ef3ff2fea8b ("nilfs2: fix deadlock of segment
constructor over I_SYNC flag") is applied and roll-forward recovery was
performed at mount time. The roll-forward recovery can happen if datasync
write is done and the file system crashes immediately after that. For
instance, we can reproduce the issue with the following steps:
< nilfs2 is mounted on /nilfs (device: /dev/sdb1) >
# dd if=/dev/zero of=/nilfs/test bs=4k count=1 && sync
# dd if=/dev/zero of=/nilfs/test conv=notrunc oflag=dsync bs=4k
count=1 && reboot -nfh
< the system will immediately reboot >
# mount -t nilfs2 /dev/sdb1 /nilfs
The deadlock occurs because iput() can run segment constructor through
writeback_single_inode() if MS_ACTIVE flag is not set on sb->s_flags. The
above commit changed segment constructor so that it calls iput()
asynchronously for inodes with i_nlink == 0, but that change was
imperfect.
This fixes the another deadlock by deferring iput() in segment constructor
even for the case that mount is not finished, that is, for the case that
MS_ACTIVE flag is not set.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Reported-by: Yuxuan Shui <yshuiv7@gmail.com> Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
MacBook Air 5,2 has the same problem as MacBook Pro 8,1 where the
built-in mic records only the right channel. Apply the same
workaround as MBP8,1 to spread the mono channel via a Cirrus codec
vendor-specific COEF setup.
CS420x codecs seem to deal only the single amps of ADC nodes even
though the nodes receive multiple inputs. This leads to the
inconsistent amp value after S3/S4 resume, for example.
The fix is just to set codec->single_adc_amp flag. Then the driver
handles these ADC amps as if single connections.
This reverts commit e4df3a0b6228
("i2c: core: Dispose OF IRQ mapping at client removal time")
Calling irq_dispose_mapping() will destroy the mapping and disassociate
the IRQ from the IRQ chip to which it belongs. Keeping it is OK, because
existent mappings are reused properly.
Also, this commit breaks drivers using devm* for IRQ management on
OF-based systems because devm* cleanup happens in device code, after
bus's remove() method returns.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Reported-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[wsa: updated the commit message with findings fromt the other bug report] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Fixes: e4df3a0b6228
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The device complies to the UAC1 standard but hides that fact with
proprietary descriptors. The autodetect quirk for Roland devices
catches the audio interface but misses the MIDI part, so a specific
quirk is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org> Reported-by: Rafa Lafuente <rafalafuente@gmail.com> Tested-by: Raphaël Doursenaud <raphael@doursenaud.fr> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
There was no check about the id string of user control elements, so we
accepted even a control element with an empty string, which is
obviously bogus. This patch adds more sanity checks of id strings.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
To take down the MOB and GMR memory types, the driver may have to issue
fence objects and thus make sure that the fence manager is taken down
after those memory types.
Reorder device init accordingly.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Experimental lockdep annotation added to the TTM lock has unveiled a
couple of lock dependency violations in the vmwgfx driver. In both
cases it turns out that the device_private::reservation_sem is not
needed so the offending code is moved out of that lock.
Acked-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Compaq Presario CQ60 laptop with CX20561 gives a wrong pin for the
built-in mic NID 0x17 instead of NID 0x1d, and it results in the
non-working mic. This patch just remaps the pin correctly via fixup.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=920604 Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Otherwise the guest can abuse that control to cause e.g. PCIe
Unsupported Request responses by disabling memory and/or I/O decoding
and subsequently causing (CPU side) accesses to the respective address
ranges, which (depending on system configuration) may be fatal to the
host.
Note that to alter any of the bits collected together as
PCI_COMMAND_GUEST permissive mode is now required to be enabled
globally or on the specific device.
This is CVE-2015-2150 / XSA-120.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Some archs (specifically PowerPC), are sensitive with the ordering of
the enabling of the calls to function tracing and setting of the
function to use to be traced.
That is, update_ftrace_function() sets what function the ftrace_caller
trampoline should call. Some archs require this to be set before
calling ftrace_run_update_code().
Another bug was discovered, that ftrace_startup_sysctl() called
ftrace_run_update_code() directly. If the function the ftrace_caller
trampoline changes, then it will not be updated. Instead a call
to ftrace_startup_enable() should be called because it tests to see
if the callback changed since the code was disabled, and will
tell the arch to update appropriately. Most archs do not need this
notification, but PowerPC does.
The problem could be seen by the following commands:
When ftrace is enabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_START_FUNC_RET command to ftrace_run_update_code(). Similarly, when
ftrace is disabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_STOP_FUNC_RET command to ftrace_run_update_code().
Since ftrace_enabled = 0, ftrace_enable_ftrace_graph_caller() is never
called.
# echo 1 > /proc/sys/kernel/ftrace_enabled
Now ftrace_enabled will be set to true, but still
ftrace_enable_ftrace_graph_caller() will not be called, which is not
desired.
Further if we execute the following after this:
# echo nop > /sys/kernel/debug/tracing/current_tracer
Now since ftrace_enabled is set it will call
ftrace_disable_ftrace_graph_caller(), which causes a kernel warning on
the ARM platform.
On the ARM platform, when ftrace_enable_ftrace_graph_caller() is called,
it checks whether the old instruction is a nop or not. If it's not a nop,
then it returns an error. If it is a nop then it replaces instruction at
that address with a branch to ftrace_graph_caller.
ftrace_disable_ftrace_graph_caller() behaves just the opposite. Therefore,
if generic ftrace code ever calls either ftrace_enable_ftrace_graph_caller()
or ftrace_disable_ftrace_graph_caller() consecutively two times in a row,
then it will return an error, which will cause the generic ftrace code to
raise a warning.
Note, x86 does not have an issue with this because the architecture
specific code for ftrace_enable_ftrace_graph_caller() and
ftrace_disable_ftrace_graph_caller() does not check the previous state,
and calling either of these functions twice in a row has no ill effect.
The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.
The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.
Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Upon a URB submission failure, the driver calls usb_free_urb()
but then manually frees the URB buffer by itself. Meanwhile
usb_free_urb() has alredy freed out that transfer buffer since
we're the only code path holding a reference to this URB.
Remove two of such invalid manual free().
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient
this can lead to a skb_under_panic due to missing skb initialisations.
Add the missing initialisations at the CAN skbuff creation times on driver
level (rx path) and in the network layer (tx path).
Reported-by: Austin Schuh <austin@peloton-tech.com> Reported-by: Daniel Steer <daniel.steer@mclaren.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The commit [63e51fd708f5: ALSA: hda - Don't take unresponsive D3
transition too serious] introduced a conditional fallback behavior to
the HD-audio controller depending on the flag set. However, it
introduced a silly bug, too, that the flag was evaluated in a reverse
way. This resulted in a regression of HD-audio controller driver
where it can't go to the fallback mode at communication errors.
Unfortunately (or fortunately?) this didn't come up until recently
because the affected code path is an error handling that happens only
on an unstable hardware chip. Most of recent chips work stably, thus
they didn't hit this problem. Now, we've got a regression report with
a VIA chip, and this seems indeed requiring the fallback to the
polling mode, and finally the bug was revealed.
The fix is a oneliner to remove the wrong logical NOT in the check.
(Lesson learned - be careful about double negation.)
The bug should be backported to stable, but the patch won't be
applicable to 3.13 or earlier because of the code splits. The stable
fix patches for earlier kernels will be posted later manually.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94021 Fixes: 63e51fd708f5 ('ALSA: hda - Don't take unresponsive D3 transition too serious') Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
On the Cortex-A9-based Armada SoCs, the MPIC is not the primary interrupt
controller. Yet, it still has to handle some per-cpu interrupt.
To do so, it is chained with the GIC using a per-cpu interrupt. However, the
current code only call irq_set_chained_handler, which is called and enable that
interrupt only on the boot CPU, which means that the parent per-CPU interrupt
is never unmasked on the secondary CPUs, preventing the per-CPU interrupt to
actually work as expected.
This was not seen until now since the only MPIC PPI users were the Marvell
timers that were not working, but not used either since the system use the ARM
TWD by default, and the ethernet controllers, that are faking there interrupts
as SPI, and don't really expect to have interrupts on the secondary cores
anyway.
Add a CPU notifier that will enable the PPI on the secondary cores when they
are brought up.
It's directly caused by 89d3cf6 [SCSI] libsas: add mutex for SMP task
execution, but shows a deeper cause: expander functions expect to be able to
cast to and treat domain devices as expanders. The correct fix is to only do
expander discover when we know we've got an expander device to avoid wrongly
casting a non-expander device.
Reported-by: Praveen Murali <pmurali@logicube.com> Tested-by: Praveen Murali <pmurali@logicube.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Problem: When IMA and VTPM are both enabled in kernel config,
kernel hangs during bootup on LE OS.
Why?: IMA calls tpm_pcr_read() which results in tpm_ibmvtpm_send
and tpm_ibmtpm_recv getting called. A trace showed that
tpm_ibmtpm_recv was hanging.
Resolution: tpm_ibmtpm_recv was hanging because tpm_ibmvtpm_send
was sending CRQ message that probably did not make much sense
to phype because of Endianness. The fix below sends correctly
converted CRQ for LE. This was not caught before because it
seems IMA is not enabled by default in kernel config and
IMA exercises this particular code path in vtpm.
Tested with IMA and VTPM enabled in kernel config and VTPM
enabled on both a BE OS and a LE OS ppc64 lpar. This exercised
CRQ and TPM command code paths in vtpm.
Patch is against Peter's tpmdd tree on github which included
Vicky's previous vtpm le patches.
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com> Reviewed-by: Ashley Lai <ashley@ahsleylai.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit fd316941c ("spi/pl022: disable port when unused") introduced a race,
which leads to possible driver lock up (easily reproducible on SMP).
The problem happens in giveback() function where the completion of the transfer
is signalled to SPI subsystem and then the HW SPI controller is disabled. Another
transfer might be setup in between, which brings driver in locked-up state.
Lockup! SPI controller is disabled and the data will never be received. Whole
SPI subsystem is waiting for transfer ACK and blocked.
So, only signal transfer completion after disabling the controller.
Fixes: fd316941c (spi/pl022: disable port when unused) Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Using the pvops kernel a NULL pointer dereference was detected on a
large machine (144 processors) when booting as dom0 in
evtchn_fifo_unmask() during assignment of a pirq.
The event channel in question was the first to need a new entry in
event_array[] in events_fifo.c. Unfortunately xen_irq_info_pirq_setup()
is called with evtchn being 0 for a new pirq and the real event channel
number is assigned to the pirq only during __startup_pirq().
It is mandatory to call xen_evtchn_port_setup() after assigning the
event channel number to the pirq to make sure all memory needed for the
event channel is allocated.
Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
cancel[_delayed]_work_sync() are implemented using
__cancel_work_timer() which grabs the PENDING bit using
try_to_grab_pending() and then flushes the work item with PENDING set
to prevent the on-going execution of the work item from requeueing
itself.
try_to_grab_pending() can always grab PENDING bit without blocking
except when someone else is doing the above flushing during
cancelation. In that case, try_to_grab_pending() returns -ENOENT. In
this case, __cancel_work_timer() currently invokes flush_work(). The
assumption is that the completion of the work item is what the other
canceling task would be waiting for too and thus waiting for the same
condition and retrying should allow forward progress without excessive
busy looping
Unfortunately, this doesn't work if preemption is disabled or the
latter task has real time priority. Let's say task A just got woken
up from flush_work() by the completion of the target work item. If,
before task A starts executing, task B gets scheduled and invokes
__cancel_work_timer() on the same work item, its try_to_grab_pending()
will return -ENOENT as the work item is still being canceled by task A
and flush_work() will also immediately return false as the work item
is no longer executing. This puts task B in a busy loop possibly
preventing task A from executing and clearing the canceling state on
the work item leading to a hang.
task A task B worker
executing work
__cancel_work_timer()
try_to_grab_pending()
set work CANCELING
flush_work()
block for work completion
completion, wakes up A
__cancel_work_timer()
while (forever) {
try_to_grab_pending()
-ENOENT as work is being canceled
flush_work()
false as work is no longer executing
}
This patch removes the possible hang by updating __cancel_work_timer()
to explicitly wait for clearing of CANCELING rather than invoking
flush_work() after try_to_grab_pending() fails with -ENOENT.
Link: http://lkml.kernel.org/g/20150206171156.GA8942@axis.com
v3: bit_waitqueue() can't be used for work items defined in vmalloc
area. Switched to custom wake function which matches the target
work item and exclusive wait and wakeup.
v2: v1 used wake_up() on bit_waitqueue() which leads to NULL deref if
the target bit waitqueue has wait_bit_queue's on it. Use
DEFINE_WAIT_BIT() and __wake_up_bit() instead. Reported by Tomeu
Vizoso.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Rabin Vincent <rabin.vincent@axis.com> Cc: Tomeu Vizoso <tomeu.vizoso@gmail.com> Tested-by: Jesper Nilsson <jesper.nilsson@axis.com> Tested-by: Rabin Vincent <rabin.vincent@axis.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The cpuset.sched_relax_domain_level can control how far we do
immediate load balancing on a system. However, it was found on recent
kernels that echo'ing a value into cpuset.sched_relax_domain_level
did not reduce any immediate load balancing.
The reason this occurred was because the update_domain_attr_tree() traversal
did not update for the "top_cpuset". This resulted in nothing being changed
when modifying the sched_relax_domain_level parameter.
This patch is able to address that problem by having update_domain_attr_tree()
allow updates for the root in the cpuset traversal.
Fixes: fc560a26acce ("cpuset: replace cpuset->stack_list with cpuset_for_each_descendant_pre()") Signed-off-by: Jason Low <jason.low2@hp.com> Signed-off-by: Zefan Li <lizefan@huawei.com> Signed-off-by: Tejun Heo <tj@kernel.org> Tested-by: Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The NDDB register holds the data that are needed by the read and write
commands.
However, during a read PIO access, the datasheet specifies that after each 32
bytes read in that register, when BCH is enabled, we have to make sure that the
RDDREQ bit is set in the NDSR register.
This fixes an issue that was seen on the Armada 385, and presumably other mvebu
SoCs, when a read on a newly erased page would end up in the driver reporting a
timeout from the NAND.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Additionally to the current DMA transfer the PDC allows to set up a next DMA
transfer. This is useful for larger SPI transfers.
The driver currently waits for ENDRX as end of the transfer. But ENDRX is set
when the current DMA transfer is done (RCR = 0), i.e. it doesn't include the
next DMA transfer.
Thus a subsequent SPI transfer could be started although there is currently a
transfer in progress. This can cause invalid accesses to the SPI slave devices
and to SPI transfer errors.
This issue has been observed on a hardware with a M25P128 SPI NOR flash.
So instead of ENDRX we should wait for RXBUFF. This flag is set if there is
no more DMA transfer in progress (RCR = RNCR = 0).
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The commit d297933cc7fc (spi: dw: Fix detecting FIFO depth) tries to fix the
logic of the FIFO detection based on the description on the comments. However,
there is a slight difference between numbers in TX Level and TX FIFO size.
So, by specification the FIFO size would be in a range 2-256 bytes. From TX
Level prospective it means we can set threshold in the range 0-(FIFO size - 1)
bytes. Hence there are currently two issues:
a) FIFO size 2 bytes is actually skipped since TX Level is 1 bit and could be
either 0 or 1 byte;
b) FIFO size is incorrectly decreased by 1 which already done by meaning of
TX Level register.
This patch fixes it eventually right.
Fixes: d297933cc7fc (spi: dw: Fix detecting FIFO depth) Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When printing the driver_override parameter when it is 4095 and 4094 bytes
long, the printing code would access invalid memory because we need count+1
bytes for printing.
Fixes: 782a985d7af2 ("PCI: Introduce new device binding path using pci_dev.driver_override") Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Alex Williamson <alex.williamson@redhat.com> CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> CC: Alexander Graf <agraf@suse.de> CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
info is in network byte order, change it back to host byte order
before use. In particular, the current code sets the MTU of the tunnel
to a wrong (too big) value.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Currently qlge_update_hw_vlan_features() will always first put the
interface down, then update features and then bring it up again. But it
is possible to hit this code while the adapter is down and this causes a
non-paired call to napi_disable(), which will get stuck.
This patch fixes it by skipping these down/up actions if the interface
is already down.
Fixes: a45adbe8d352 ("qlge: Enhance nested VLAN (Q-in-Q) handling.") Cc: Harish Patil <harish.patil@qlogic.com> Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When creating a bpf classifier in tc with priority collisions and
invoking automatic unique handle assignment, cls_bpf_grab_new_handle()
will return a wrong handle id which in fact is non-unique. Usually
altering of specific filters is being addressed over major id, but
in case of collisions we result in a filter chain, where handle ids
address individual cls_bpf_progs inside the classifier.
Issue is, in cls_bpf_grab_new_handle() we probe for head->hgen handle
in cls_bpf_get() and in case we found a free handle, we're supposed
to use exactly head->hgen. In case of insufficient numbers of handles,
we bail out later as handle id 0 is not allowed.
Fixes: 7d1d65cb84e1 ("net: sched: cls_bpf: add BPF-based classifier") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In cls_bpf_modify_existing(), we read out the number of filter blocks,
do some sanity checks, allocate a block on that size, and copy over the
BPF instruction blob from user space, then pass everything through the
classic BPF checker prior to installation of the classifier.
We should reject mismatches here, there are 2 scenarios: the number of
filter blocks could be smaller than the provided instruction blob, so
we do a partial copy of the BPF program, and thus the instructions will
either be rejected from the verifier or a valid BPF program will be run;
in the other case, we'll end up copying more than we're supposed to,
and most likely the trailing garbage will be rejected by the verifier
as well (i.e. we need to fit instruction pattern, ret {A,K} needs to be
last instruction, load/stores must be correct, etc); in case not, we
would leak memory when dumping back instruction patterns. The code should
have only used nla_len() as Dave noted to avoid this from the beginning.
Anyway, lets fix it by rejecting such load attempts.
Fixes: 7d1d65cb84e1 ("net: sched: cls_bpf: add BPF-based classifier") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Sometimes while CPU have some load and ath5k doing the wireless
interface reset the whole WiSoC completely freezes. Set of tests shows
that using atomic delay function while we wait interface reset helps to
avoid such freezes.
The easiest way to reproduce this issue: create a station interface,
start continous scan with wpa_supplicant and load CPU by something. Or
just create multiple station interfaces and put them all in continous
scan.
This patch partially reverts the commit 1846ac3dbec0 ("ath5k: Use
usleep_range where possible"), which replaces initial udelay()
by usleep_range().
I do not know actual source of this issue, but all looks like that HW
freeze is caused by transaction on internal SoC bus, while wireless
block is in reset state.
Also I should note that I do not know how many chips are affected, but I
did not see this issue with chips, other than AR5312.
CC: Jiri Slaby <jirislaby@gmail.com> CC: Nick Kossifidis <mickflemm@gmail.com> CC: Luis R. Rodriguez <mcgrof@do-not-panic.com> Fixes: 1846ac3dbec0 ("ath5k: Use usleep_range where possible") Reported-by: Christophe Prevotaux <c.prevotaux@rural-networks.com> Tested-by: Christophe Prevotaux <c.prevotaux@rural-networks.com> Tested-by: Eric Bree <ebree@nltinc.com> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Our UC-KLEE tool found a kernel memory leak of 512 bytes (on x86_64) for
each call to gssp_accept_sec_context_upcall()
(net/sunrpc/auth_gss/gss_rpc_upcall.c). Since it appears that this call
can be triggered by remote connections (at least, from a cursory a
glance at the call chain), it may be exploitable to cause kernel memory
exhaustion. We found the bug in kernel 3.16.3, but it appears to date
back to commit 9dfd87da1aeb0fd364167ad199f40fe96a6a87be (2013-08-20).
The gssp_accept_sec_context_upcall() function performs a pair of calls
to gssp_alloc_receive_pages() and gssp_free_receive_pages(). The first
allocates memory for arg->pages. The second then frees the pages
pointed to by the arg->pages array, but not the array itself.
Reported-by: David A. Ramos <daramos@stanford.edu> Fixes: 9dfd87da1aeb ("rpc: fix huge kmalloc's in gss-proxy”) Signed-off-by: David A. Ramos <daramos@stanford.edu> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an
infinite timeout (0) would be passed to the underlying tty-driver's
wait_until_sent-operation as a negative timeout (-1), causing it to
return immediately.
This manifests itself for example as tcdrain() returning immediately,
drivers not honouring the drain flags when setting terminal attributes,
or even dropped data on close as a requested infinite closing-wait
timeout would be ignored.
The first symptom was reported by Asier LLANO who noted that tcdrain()
returned prematurely when using the ftdi_sio usb-serial driver.
Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the
underlying tty driver.
Note that the serial-core wait_until_sent-implementation is not affected
by this bug due to a lucky chance (comparison to an unsigned maximum
timeout), and neither is the cyclades one that had an explicit check for
negative timeouts, but all other tty drivers appear to be affected.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: ZIV-Asier Llano Palacios <asier.llano@cgglobal.com> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6ae9200f2cab7 ("enlarge console.name") increased the storage
for the console name to 16 bytes, but not the corresponding
struct console_cmdline::name storage. Console names longer than
8 bytes cause read beyond end-of-string and failure to match
console; I'm not sure if there are other unexpected consequences.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
But it still misses one point. As John Paul correctly points out, we
do not care about setting date. If somebody ever changes wall
time backwards (by mistake for example), tty timestamps are never
updated until the original wall time passes.
So check the absolute difference of times and if it large than "8
seconds or so", always update the time. That means we will update
immediatelly when changing time. Ergo, CAP_SYS_TIME can foul the
check, but it was always that way.
Thanks John for serving me this so nicely debugged.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: John Paul Perry <john_paul.perry@alcatel-lucent.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
I'm still receiving reports to my email address, so let's point this
at the linux-serial mailing list instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.
Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks
Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.
The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.
This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.
This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When using the fast file fsync code path we can miss the fact that new
writes happened since the last file fsync and therefore return without
waiting for the IO to finish and write the new extents to the fsync log.
Here's an example scenario where the fsync will miss the fact that new
file data exists that wasn't yet durably persisted:
1. fs_info->last_trans_committed == N - 1 and current transaction is
transaction N (fs_info->generation == N);
2. do a buffered write;
3. fsync our inode, this clears our inode's full sync flag, starts
an ordered extent and waits for it to complete - when it completes
at btrfs_finish_ordered_io(), the inode's last_trans is set to the
value N (via btrfs_update_inode_fallback -> btrfs_update_inode ->
btrfs_set_inode_last_trans);
4. transaction N is committed, so fs_info->last_trans_committed is now
set to the value N and fs_info->generation remains with the value N;
5. do another buffered write, when this happens btrfs_file_write_iter
sets our inode's last_trans to the value N + 1 (that is
fs_info->generation + 1 == N + 1);
6. transaction N + 1 is started and fs_info->generation now has the
value N + 1;
7. transaction N + 1 is committed, so fs_info->last_trans_committed
is set to the value N + 1;
8. fsync our inode - because it doesn't have the full sync flag set,
we only start the ordered extent, we don't wait for it to complete
(only in a later phase) therefore its last_trans field has the
value N + 1 set previously by btrfs_file_write_iter(), and so we
have:
Which made us not log the last buffered write and exit the fsync
handler immediately, returning success (0) to user space and resulting
in data loss after a crash.
This can actually be triggered deterministically and the following excerpt
from a testcase I made for xfstests triggers the issue. It moves a dummy
file across directories and then fsyncs the old parent directory - this
is just to trigger a transaction commit, so moving files around isn't
directly related to the issue but it was chosen because running 'sync' for
example does more than just committing the current transaction, as it
flushes/waits for all file data to be persisted. The issue can also happen
at random periods, since the transaction kthread periodicaly commits the
current transaction (about every 30 seconds by default).
The body of the test is:
# Create our main test file 'foo', the one we check for data loss.
# By doing an fsync against our file, it makes btrfs clear the 'needs_full_sync'
# bit from its flags (btrfs inode specific flags).
$XFS_IO_PROG -f -c "pwrite -S 0xaa 0 8K" \
-c "fsync" $SCRATCH_MNT/foo | _filter_xfs_io
# Now create one other file and 2 directories. We will move this second file
# from one directory to the other later because it forces btrfs to commit its
# currently open transaction if we fsync the old parent directory. This is
# necessary to trigger the data loss bug that affected btrfs.
mkdir $SCRATCH_MNT/testdir_1
touch $SCRATCH_MNT/testdir_1/bar
mkdir $SCRATCH_MNT/testdir_2
# Make sure everything is durably persisted.
sync
# Write more 8Kb of data to our file.
$XFS_IO_PROG -c "pwrite -S 0xbb 8K 8K" $SCRATCH_MNT/foo | _filter_xfs_io
# Move our 'bar' file into a new directory.
mv $SCRATCH_MNT/testdir_1/bar $SCRATCH_MNT/testdir_2/bar
# Fsync our first directory. Because it had a file moved into some other
# directory, this made btrfs commit the currently open transaction. This is
# a condition necessary to trigger the data loss bug.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/testdir_1
# Now fsync our main test file. If the fsync succeeds, we expect the 8Kb of
# data we wrote previously to be persisted and available if a crash happens.
# This did not happen with btrfs, because of the transaction commit that
# happened when we fsynced the parent directory.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo
# Simulate a crash/power loss.
_load_flakey_table $FLAKEY_DROP_WRITES
_unmount_flakey
# Now check that all data we wrote before are available.
echo "File content after log replay:"
od -t x1 $SCRATCH_MNT/foo
status=0
exit
The expected golden output for the test, which is what we get with this
fix applied (or when running against ext3/4 and xfs), is:
wrote 8192/8192 bytes at offset 0
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
wrote 8192/8192 bytes at offset 8192
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
File content after log replay: 0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
* 0020000 bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
* 0040000
Without this fix applied, the output shows the test file does not have
the second 8Kb extent that we successfully fsynced:
wrote 8192/8192 bytes at offset 0
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
wrote 8192/8192 bytes at offset 8192
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
File content after log replay: 0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
* 0020000
So fix this by skipping the fsync only if we're doing a full sync and
if the inode's last_trans is <= fs_info->last_trans_committed, or if
the inode is already in the log. Also remove setting the inode's
last_trans in btrfs_file_write_iter since it's useless/unreliable.
Also because btrfs_file_write_iter no longer sets inode->last_trans to
fs_info->generation + 1, don't set last_trans to 0 if we bail out and don't
bail out if last_trans is 0, otherwise something as simple as the following
example wouldn't log the second write on the last fsync:
1. write to file
2. fsync file
3. fsync file
|--> btrfs_inode_in_log() returns true and it set last_trans to 0
4. write to file
|--> btrfs_file_write_iter() no longers sets last_trans, so it
remained with a value of 0
5. fsync
|--> inode->last_trans == 0, so it bails out without logging the
second write
A test case for xfstests will be sent soon.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
'ret_from_fork' checks TIF_IA32 to determine whether 'pt_regs' and
the related state make sense for 'ret_from_sys_call'. This is
entirely the wrong check. TS_COMPAT would make a little more
sense, but there's really no point in keeping this optimization
at all.
This fixes a return to the wrong user CS if we came from int
0x80 in a 64-bit task.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/4710be56d76ef994ddf59087aad98c000fbab9a4.1424989793.git.luto@amacapital.net
[ Backported from tip:x86/asm. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
DMA_BIT_MASK of 64 is not valid dma address mask for OMAPs, it should be
set to 32.
The 64 was introduced by commit (in 2009): a152ff24b978 ASoC: OMAP: Make DMA 64 aligned
But the dma_mask and coherent_dma_mask can not be used to specify alignment.
Fixes: a152ff24b978 (ASoC: OMAP: Make DMA 64 aligned) Reported-by: Grygorii Strashko <Grygorii.Strashko@linaro.org> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
i915.ko depends upon the acpi/video.ko module and so refuses to load if
ACPI is disabled at runtime if for example the BIOS is broken beyond
repair. acpi/video provides an optional service for i915.ko and so we
should just allow the modules to load, but do no nothing in order to let
the machines boot correctly.
Reported-by: Bill Augur <bill-auger@programmer.net> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@intel.com> Acked-by: Aaron Lu <aaron.lu@intel.com>
[ rjw: Fixed up the new comment in acpi_video_init() ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Tommi Rantala <tt.rantala@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
eCryptfs can't be aware of what to expect when after passing an
arbitrary ioctl command through to the lower filesystem. The ioctl
command may trigger an action in the lower filesystem that is
incompatible with eCryptfs.
One specific example is when one attempts to use the Btrfs clone
ioctl command when the source file is in the Btrfs filesystem that
eCryptfs is mounted on top of and the destination fd is from a new file
created in the eCryptfs mount. The ioctl syscall incorrectly returns
success because the command is passed down to Btrfs which thinks that it
was able to do the clone operation. However, the result is an empty
eCryptfs file.
This patch allows the trim, {g,s}etflags, and {g,s}etversion ioctl
commands through and then copies up the inode metadata from the lower
inode to the eCryptfs inode to catch any changes made to the lower
inode's metadata. Those five ioctl commands are mostly common across all
filesystems but the whitelist may need to be further pruned in the
future.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Cc: Rocko <rockorequin@hotmail.com> Cc: Colin Ian King <colin.king@canonical.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ luis: 3.16-stable, just to make 6d65261a09ad ("eCryptfs: don't pass
fs-specific ioctl commands through") a clean cherry-pick ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This patch integrates Cyber Cortex AV boards with the existing
ftdi_jtag_quirk in order to use serial port 0 with JTAG which is
required by the manufacturers' software.
Steps: 2
[ftdi_sio_ids.h]
1. Defined the device PID
[ftdi_sio.c]
2. Added a macro declaration to the ids array, in order to enable the
jtag quirk for the device.
Signed-off-by: Max Mansfield <max.m.mansfield@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Currently the guest exit trace event saves the VCPU pointer to the
structure, and the guest PC is retrieved by dereferencing it when the
event is printed rather than directly from the trace record. This isn't
safe as the printing may occur long afterwards, after the PC has changed
and potentially after the VCPU has been freed. Usually this results in
the same (wrong) PC being printed for multiple trace events. It also
isn't portable as userland has no way to access the VCPU data structure
when interpreting the trace record itself.
Lets save the actual PC in the structure so that the correct value is
accessible later.
Fixes: 669e846e6c4e ("KVM/MIPS32: MIPS arch specific APIs for KVM") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
A block-local variable stores error code but btrfs_get_blocks_direct may
not return it in the end as there's a ret defined in the function scope.
Fixes: d187663ef24c ("Btrfs: lock extents as we map them in DIO") Signed-off-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Set the internal device state to to disabled after hardware reset in stop flow.
This will cover cases when driver was not brought to disabled state because of
an error and in stop flow we wish not to retry the reset.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Reading of analog input channels by the `INSN_READ` comedi instruction
is broken for all except channel 0. `pci171x_ai_insn_read()` calls
`pci171x_ai_read_sample()` with the wrong value for the third parameter.
It is supposed to be the current index in a channel list (which is
always of length 1 in this case, so the index should be 0), but instead
it is passing the actual channel number. `pci171x_ai_read_sample()`
checks the channel number encoded in the raw sample value read from the
hardware matches the channel number stored in the specified index of the
previously set up channel list and returns `-ENODATA` if it doesn't
match. Since the index should always be 0 in this case, the match will
fail unless the channel number is also 0. Fix it by passing 0 as the
channel index.
Note that when the bug first appeared, it was `pci171x_ai_dropout()`
that was called with the wrong parameter value. `pci171x_ai_dropout()`
got replaced with `pci171x_ai_read_sample()` in commit 7fd2dae2500d
("staging: comedi: adv_pci1710: introduce pci171x_ai_read_sample()").
Fixes: 16c7eb6047bb ("staging: comedi: adv_pci1710: always enable PCI171x_PARANOIDCHECK code") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: backported to 3.16: used Ian's backport ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
These device ID's are not associated with the cp210x module currently,
but should be. This patch allows the devices to operate upon connecting
them to the usb bus as intended.
Signed-off-by: Michiel van de Garde <mgparser@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
/proc/<pid>/maps currently don't annotate stack vma with "[stack]"
This is because KSTK_ESP ie expected to return usermode SP of tsk while
currently it returns the kernel mode SP of a sleeping tsk.
While the fix is trivial, we also need to adjust the ARC kernel stack
unwinder to not use KSTK_SP and friends any more.
The current minstrel_ht rate control behavior is somewhat optimistic in
trying to find optimum TX rate. While this is usually fine for normal
Data frames, there are cases where a more conservative set of retry
parameters would be beneficial to make the connection more robust.
EAPOL frames are critical to the authentication and especially the
EAPOL-Key message 4/4 (the last message in the 4-way handshake) is
important to get through to the AP. If that message is lost, the only
recovery mechanism in many cases is to reassociate with the AP and start
from scratch. This can often be avoided by trying to send the frame with
more conservative rate and/or with more link layer retries.
In most cases, minstrel_ht is currently using the initial EAPOL-Key
frames for probing higher rates and this results in only five link layer
transmission attempts (one at high(ish) MCS and four at MCS0). While
this works with most APs, it looks like there are some deployed APs that
may have issues with the EAPOL frames using HT MCS immediately after
association. Similarly, there may be issues in cases where the signal
strength or radio environment is not good enough to be able to get
frames through even at couple of MCS 0 tries.
The best approach for this would likely to be to reduce the TX rate for
the last rate (3rd rate parameter in the set) to a low basic rate (say,
6 Mbps on 5 GHz and 2 or 5.5 Mbps on 2.4 GHz), but doing that cleanly
requires some more effort. For now, we can start with a simple one-liner
that forces the minimum rate to be used for EAPOL frames similarly how
the TX rate is selected for the IEEE 802.11 Management frames. This does
result in a small extra latency added to the cases where the AP would be
able to receive the higher rate, but taken into account how small number
of EAPOL frames are used, this is likely to be insignificant. A future
optimization in the minstrel_ht design can also allow this patch to be
reverted to get back to the more optimized initial TX rate.
It should also be noted that many drivers that do not use minstrel as
the rate control algorithm are already doing similar workarounds by
forcing the lowest TX rate to be used for EAPOL frames.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Tested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Add missing error handling when registering the tty device at port
probe. This avoids trying to remove an uninitialised character device
when the port device is removed.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Greg Kroah-Hartman <greg@kroah.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fix return value in probe error path, which could end up returning
success (0) on errors. This could in turn lead to use-after-free or
double free (e.g. in port_remove) when the port device is removed.
Fixes: c706ebdfc895 ("USB: usb-serial: call port_probe and port_remove
at the right times") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Greg Kroah-Hartman <greg@kroah.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
These product identifiers (PID) all deal with marine NMEA format data
used on motor boats and yachts. We supply the programmed devices to
Chetco, for use inside their equipment. The PIDs are a direct copy of
our Windows device drivers (FTDI drivers with altered PIDs).
Signed-off-by: Mark Glover <mark@actisense.com>
[johan: edit commit message slightly ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
A bulk-out size smaller than the end-point size is indeed valid. The
offending commit broke the usb-debug driver for EHCI debug devices,
which use 8-byte buffers.
Fixes: 5083fd7bdfe6 ("USB: serial: make bulk_out_size a lower limit") Reported-by: "Li, Elvin" <elvin.li@intel.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
While adding support loading kernel and initrd above 4G to grub2 in legacy
mode, I was referring to efi_high_alloc().
That will allocate buffer for kernel and then initrd, and initrd will
use kernel buffer start as limit.
During testing found two buffers will be overlapped when initrd size is
very big like 400M.
It turns out efi_high_alloc() boundary checking is not right.
end - size will be the new start, and should not compare new
start with max, we need to make sure end is smaller than max.
[ Basically, with the current efi_high_alloc() code it's possible to
allocate memory above 'max', because efi_high_alloc() doesn't check
that the tail of the allocation is below 'max'.
If you have an EFI memory map with a single entry that looks like so,
[0xc0000000-0xc0004000]
And want to allocate 0x3000 bytes below 0xc0003000 the current code
will allocate [0xc0001000-0xc0004000], not [0xc0000000-0xc0003000]
like you would expect. - Matt ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com>
[ luis: backported to 3.16:
- file rename: drivers/firmware/efi/libstub/efi-stub-helper.c ->
drivers/firmware/efi/efi-stub-helper.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Like the JMicron JMS567 enclosures with the JMS539 choke on report-opcodes,
so avoid it.
Tested-and-reported-by: Tom Arild Naess <tanaess@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When a signal is delivered, the information in the siginfo structure
is copied to userspace. Good security practice dicatates that the
unused fields in this structure should be initialized to 0 so that
random kernel stack data isn't exposed to the user. This patch adds
such an initialization to the two places where usbfs raises signals.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Dave Mielke <dave@mielke.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Include the high order bit fields for Max scratchpad buffers when
calculating how many scratchpad buffers are needed.
I'm suprised this hasn't caused more issues, we never allocated more than
32 buffers even if xhci needed more. Either we got lucky and xhci never
really used past that area, or then we got enough zeroed dma memory anyway.
Should be backported as far back as possible
Reported-by: Tim Chen <tim.c.chen@linux.intel.com> Tested-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The commit 973747928514 ("usb: host: xhci-plat: add support for the Armada
375/38x XHCI controllers") extended the xhci-plat driver to support the Armada
375/38x SoCs, mostly by adding a quirk configuring the MBUS window.
However, that quirk was run before the clock the controllers needs has been
enabled. This usually worked because the clock was first enabled by the
bootloader, and left as such until the driver is probe, where it tries to
access the MBUS configuration registers before enabling the clock.
Things get messy when EPROBE_DEFER is involved during the probe, since as part
of its error path, the driver will rightfully disable the clock. When the
driver will be reprobed, it will retry to access the MBUS registers, but this
time with the clock disabled, which hangs forever.
Fix this by running the quirks after the clock has been enabled by the driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This has been broken for a long time: it broke first in 2.6.35, then was
almost fixed in 2.6.36 but this one-liner slipped through the cracks.
The bug shows up as an infinite loop in Windows 7 (and newer) boot on
32-bit hosts without EPT.
Windows uses CMPXCHG8B to write to page tables, which causes a
page fault if running without EPT; the emulator is then called from
kvm_mmu_page_fault. The loop then happens if the higher 4 bytes are
not 0; the common case for this is that the NX bit (bit 63) is 1.
Fixes: 6550e1f165f384f3a46b60a1be9aba4bc3c2adad Fixes: 16518d5ada690643453eb0aef3cc7841d3623c2d Reported-by: Erik Rull <erik.rull@rdsoftware.de> Tested-by: Erik Rull <erik.rull@rdsoftware.de> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The "Extended Compat ID OS Feature Descriptor Specification" does not
require the (sub)compatible ids to be NUL-terminated, because they
are placed in a fixed-size buffer and only unused parts of it should
contain NULs. If the buffer is fully utilized, there is no place for NULs.
Consequently, the code which uses desc->ext_compat_id never expects the
data contained to be NUL terminated.
If the compatible id is stored after sub-compatible id, and the compatible
id is full length (8 bytes), the (useless) NUL terminator overwrites the
first byte of the sub-compatible id.
If the sub-compatible id is full length (8 bytes), the (useless) NUL
terminator ends up out of the buffer. The situation can happen in the RNDIS
function, where the buffer is a part of struct f_rndis_opts. The next
member of struct f_rndis_opts is a mutex, so its first byte gets
overwritten. The said byte is a part of a mutex'es member which contains
the information on whether the muext is locked or not. This can lead to a
deadlock, because, in a configfs-composed gadget when a function is linked
into a configuration with config_usb_cfg_link(), usb_get_function()
is called, which then calls rndis_alloc(), which tries locking the same
mutex and (wrongly) finds it already locked.
This patch eliminates NUL terminating of the (sub)compatible id.
Fixes: da4243145fb1: "usb: gadget: configfs: OS Extended Compatibility descriptors support" Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In the wrapper the IRQ disable should be done by writing 1's to the
IRQ*_CLR register. Existing code is broken because it instead writes
zeros to IRQ*_SET register.
Fix this by adding functions dwc3_omap_write_irqmisc_clr() and
dwc3_omap_write_irq0_clr() which do the right thing.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Since commit c8231a9af8147f8a ("iio: mxs-lradc: compute temperature
from channel 8 and 9") with the removal of adc channel 9 there is
no 1-1 mapping in the channel spec.
All hwmon channel values above 9 are accessible via there index minus
one. So add a hidden iio channel 9 to fix this issue.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The intention is obviously to sign-extend a 12 bit quantity. But
because of C's promotion rules, the assignment is equivalent to "val16
&= 0xfff;". Use the proper API for this.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Using the touchscreen while running buffered capture results in the
buffer reporting lots of wrong values, often just zeros. This is because
we push readings to the buffer every time a touchscreen interrupt
arrives, including when the buffer's own conversions have not yet
finished. So let's only push to the buffer when its conversions are
ready.
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Reading a channel through sysfs, or starting a buffered capture, can
occasionally turn off the touchscreen.
This is because the read_raw() and buffer preenable()/postdisable()
callbacks unschedule current conversions on all channels. If a delay
channel happens to schedule a touchscreen conversion at the same time,
the conversion gets cancelled and the touchscreen sequence stops.
This is probably related to this note from the reference manual:
"If a delay group schedules channels to be sampled and a manual
write to the schedule field in CTRL0 occurs while the block is
discarding samples, the LRADC will switch to the new schedule
and will not sample the channels that were previously scheduled.
The time window for this to happen is very small and lasts only
while the LRADC is discarding samples."
So make the callbacks only unschedule conversions for the channels they
use. This means channel 0 for read_raw() and channels 0-5 for the buffer
(if the touchscreen is enabled). Since the touchscreen uses different
channels (6 and 7), it no longer gets turned off.
This is tested and fixes the issue on i.MX28, but hasn't been tested on
i.MX23.
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Reading a channel through sysfs, or starting a buffered capture, will
currently turn off the touchscreen. This is because the read_raw() and
buffer preenable()/postdisable() callbacks disable interrupts for all
LRADC channels, including those the touchscreen uses.
So make the callbacks only disable interrupts for the channels they use.
This means channel 0 for read_raw() and channels 0-5 for the buffer (if
the touchscreen is enabled). Since the touchscreen uses different
channels (6 and 7), it no longer gets turned off.
Note that only i.MX28 is affected by this issue, i.MX23 should be fine.
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The touchscreen was initially designed [1] to map all of its physical
channels to one virtual channel, leaving buffered capture to use the
remaining 7 virtual channels. When the touchscreen was reimplemented
[2], it was made to use four virtual channels, which overlap and
conflict with the channels the buffer uses.
As a result, when the buffer is enabled, the touchscreen's virtual
channels are remapped to whichever physical channels the buffer was
configured with, causing the touchscreen to read those instead of the
touch measurement channels. Effectively the touchscreen stops working.
So here we separate the channels again, giving the touchscreen 2 virtual
channels and the buffer 6. We can't give the touchscreen just 1 channel
as before, as the current pressure calculation requires 2 channels to be
read at the same time.
This makes the touchscreen continue to work during buffered capture. It
has been tested on i.MX28, but not on i.MX23.
[1] 06ddd353f5c8 ("iio: mxs: Implement support for touchscreen")
[2] dee05308f602 ("Staging/iio/adc/touchscreen/MXS: add interrupt driven
touch detection")
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Each inode of nilfs2 stores a root node of a b-tree, and it turned out to
have a memory overrun issue:
Each b-tree node of nilfs2 stores a set of key-value pairs and the number
of them (in "bn_nchildren" member of nilfs_btree_node struct), as well as
a few other "bn_*" members.
Since the value of "bn_nchildren" is used for operations on the key-values
within the b-tree node, it can cause memory access overrun if a large
number is incorrectly set to "bn_nchildren".
For instance, nilfs_btree_node_lookup() function determines the range of
binary search with it, and too large "bn_nchildren" leads
nilfs_btree_node_get_key() in that function to overrun.
As for intermediate b-tree nodes, this is prevented by a sanity check
performed when each node is read from a drive, however, no sanity check
has been done for root nodes stored in inodes.
This patch fixes the issue by adding missing sanity check against b-tree
root nodes so that it's called when on-memory inodes are read from ifile,
inode metadata file.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The native (64-bit) sigval_t union contains sival_int (32-bit) and
sival_ptr (64-bit). When a compat application invokes a syscall that
takes a sigval_t value (as part of a larger structure, e.g.
compat_sys_mq_notify, compat_sys_timer_create), the compat_sigval_t
union is converted to the native sigval_t with sival_int overlapping
with either the least or the most significant half of sival_ptr,
depending on endianness. When the corresponding signal is delivered to a
compat application, on big endian the current (compat_uptr_t)sival_ptr
cast always returns 0 since sival_int corresponds to the top part of
sival_ptr. This patch fixes copy_siginfo_to_user32() so that sival_int
is copied to the compat_siginfo_t structure.
This is essentially a partial revert of the commit [b1920c21102a:
'ALSA: hda - Enable runtime PM on Panther Point']. There was a bug
report showing the HD-audio bus hang during runtime PM on HP Spectre
XT.
projects / thirdparty / kernel / stable.git / log
