fw_sysfs_wait_timeout may return err with -ENOENT
at fw_load_sysfs_fallback and firmware is already
in abort status, no need to abort again, so skip it.
This issue is caused by concurrent situation like below:
when thread 1# wait firmware loading, thread 2# may write
-1 to abort loading and wakeup thread 1# before it timeout.
so wait_for_completion_killable_timeout of thread 1# would
return remaining time which is != 0 with fw_st->status
FW_STATUS_ABORTED.And the results would be converted into
err -ENOENT in __fw_state_wait_common and transfered to
fw_load_sysfs_fallback in thread 1#.
The -ENOENT means firmware status is already at ABORTED,
so fw_load_sysfs_fallback no need to get mutex to abort again.
-----------------------------
thread 1#,wait for loading
fw_load_sysfs_fallback
->fw_sysfs_wait_timeout
->__fw_state_wait_common
->wait_for_completion_killable_timeout
in __fw_state_wait_common,
...
93 ret = wait_for_completion_killable_timeout(&fw_st->completion, timeout);
94 if (ret != 0 && fw_st->status == FW_STATUS_ABORTED)
95 return -ENOENT;
96 if (!ret)
97 return -ETIMEDOUT;
98
99 return ret < 0 ? ret : 0;
-----------------------------
thread 2#, write -1 to abort loading
firmware_loading_store
->fw_load_abort
->__fw_load_abort
->fw_state_aborted
->__fw_state_set
->complete_all
in __fw_state_set,
...
111 if (status == FW_STATUS_DONE || status == FW_STATUS_ABORTED)
112 complete_all(&fw_st->completion);
-------------------------------------------
BTW,the double abort issue would not cause kernel panic or create an issue,
but slow down it sometimes.The change is just a minor optimization.
Don't call quiesce(1) and quiesce(0) if array is already suspended,
otherwise in level_store, the array is writable after mddev_detach
in below part though the intention is to make array writable after
resume.
This is happening because we have a pending doorbell that requires
retrigger. As SW retriggering is done in a tasklet, we trigger the
circular dependency above.
The easy cop-out is to provide a retrigger callback that doesn't
require acquiring any extra lock.
In certain circumstances, the XHCI SuperSpeed instance in park mode
can fail to recover, thus on Amlogic G12A/G12B/SM1 SoCs when there is high
load on the single XHCI SuperSpeed instance, the controller can crash like:
xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
xhci-hcd xhci-hcd.0.auto: Host halt failed, -110
xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
hub 2-1.1:1.0: hub_ext_port_status failed (err = -22)
xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
usb 2-1.1-port1: cannot reset (err = -22)
Setting the PARKMODE_DISABLE_SS bit in the DWC3_USB3_GUCTL1 mitigates
the issue. The bit is described as :
"When this bit is set to '1' all SS bus instances in park mode are disabled"
Synopsys explains:
The GUCTL1.PARKMODE_DISABLE_SS is only available in
dwc_usb3 controller running in host mode.
This should not be set for other IPs.
This can be disabled by default based on IP, but I recommend to have a
property to enable this feature for devices that need this.
CC: Dongjin Kim <tobetter@gmail.com> Cc: Jianxin Pan <jianxin.pan@amlogic.com> Cc: Thinh Nguyen <thinhn@synopsys.com> Cc: Jun Li <lijun.kernel@gmail.com> Reported-by: Tim <elatllat@gmail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
From the measured hardware signal, OV5695 reset pin goes high for a
short period of time during boot-up. From the sensor specification, the
reset pin is active low and the DT binding defines the pin as active
low, which means that the values set by the driver are inverted and thus
the value requested in probe ends up high.
Fix it by changing probe to request the reset GPIO initialized to high,
which makes the initial state of the physical signal low.
In addition, DOVDD rising must occur before DVDD rising from spec., but
regulator_bulk_enable() API enables all the regulators asynchronously.
Use an explicit loops of regulator_enable() instead.
For power off sequence, it is required that DVDD falls first. Given the
bulk API does not give any guarantee about the order of regulators,
change the driver to use regulator_disable() instead.
The sensor also requires a delay between reset high and first I2C
transaction, which was assumed to be 8192 XVCLK cycles, but 1ms is
recommended by the vendor. Fix this as well.
There is a potential race between ioc_release_fn() and
ioc_clear_queue() as shown below, due to which below kernel
crash is observed. It also can result into use-after-free
issue.
context#1: context#2:
ioc_release_fn() __ioc_clear_queue() gets the same icq
->spin_lock(&ioc->lock); ->spin_lock(&ioc->lock);
->ioc_destroy_icq(icq);
->list_del_init(&icq->q_node);
->call_rcu(&icq->__rcu_head,
icq_free_icq_rcu);
->spin_unlock(&ioc->lock);
->ioc_destroy_icq(icq);
->hlist_del_init(&icq->ioc_node);
This results into below crash as this memory
is now used by icq->__rcu_head in context#1.
There is a chance that icq could be free'd
as well.
Fix this by adding a new ICQ_DESTROYED flag in ioc_destroy_icq() to
indicate this icq is once marked as destroyed. Also, ensure
__ioc_clear_queue() is accessing icq within rcu_read_lock/unlock so
that icq doesn't get free'd up while it is still using it.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org> Co-developed-by: Pradeep P V K <ppvk@codeaurora.org> Signed-off-by: Pradeep P V K <ppvk@codeaurora.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
irq_domain_alloc_irqs_hierarchy() has 3 call sites in the compilation unit
but only one of them checks for the pointer which is being dereferenced
inside the called function. Move the check into the function. This allows
for catching the error instead of the following crash:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
PC is at 0x0
LR is at gpiochip_hierarchy_irq_domain_alloc+0x11f/0x140
...
[<c06c23ff>] (gpiochip_hierarchy_irq_domain_alloc)
[<c0462a89>] (__irq_domain_alloc_irqs)
[<c0462dad>] (irq_create_fwspec_mapping)
[<c06c2251>] (gpiochip_to_irq)
[<c06c1c9b>] (gpiod_to_irq)
[<bf973073>] (gpio_irqs_init [gpio_irqs])
[<bf974048>] (gpio_irqs_exit+0xecc/0xe84 [gpio_irqs])
Code: bad PC value
3a6b6c6fb23667fa ("efi: Make EFI_MEMORY_ATTRIBUTES_TABLE initialization common across all architectures")
moved the call to efi_memattr_init() from ARM specific to the generic
EFI init code, in order to be able to apply the restricted permissions
described in that table on x86 as well.
We never enabled this feature fully on i386, and so mapping and
reserving this table is pointless. However, due to the early call to
memblock_reserve(), the memory bookkeeping gets confused to the point
where it produces the splat below when we try to map the memory later
on:
Let's work around this by disregarding the memory attributes table
altogether on i386, which does not result in a loss of functionality
or protection, given that we never consumed the contents.
Before this patch, run_queue would demote glocks based on whether
there are any more holders. But if the glock has pending revokes that
haven't been written to the media, giving up the glock might end in
file system corruption if the revokes never get written due to
io errors, node crashes and fences, etc. In that case, another node
will replay the metadata blocks associated with the glock, but
because the revoke was never written, it could replay that block
even though the glock had since been granted to another node who
might have made changes.
This patch changes the logic in run_queue so that it never demotes
a glock until its count of pending revokes reaches zero.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a potential mem leak when pstore_init_fs failed,
since the pstore compression maybe unlikey to initialized
successfully. We must clean up the allocation once this
unlikey issue happens.
There is also refcount issue, as well:
WARNING: CPU: 1 PID: 1 at lib/refcount.c:28 refcount_warn_saturate+0xf8/0x170
The issue is that we make an erroneous extra call to scsi_host_put()
for that host:
So in ahci_init_one()->ata_host_alloc_pinfo()->ata_host_alloc(), we setup
a device release method - ata_devres_release() - which intends to release
the SCSI hosts:
static void ata_devres_release(struct device *gendev, void *res)
{
...
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap = host->ports[i];
if (!ap)
continue;
if (ap->scsi_host)
scsi_host_put(ap->scsi_host);
}
...
}
However in the ata_scsi_add_hosts() error path, we also call
scsi_host_put() for the SCSI hosts.
Fix by removing the the scsi_host_put() calls in ata_scsi_add_hosts() and
leave this to ata_devres_release().
Fixes: f31871951b38 ("libata: separate out ata_host_alloc() and ata_host_register()") Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix build fault when CONFIG_HWMON is a module, and CONFIG_VIDEO_I2C
as builtin. This is due to 'imply hwmon' in the respective Kconfig.
Issue build log:
ld: drivers/media/i2c/video-i2c.o: in function `amg88xx_hwmon_init':
video-i2c.c:(.text+0x2e1): undefined reference to `devm_hwmon_device_register_with_info
Cc: rdunlap@infradead.org Fixes: acbea6798955 (media: video-i2c: add hwmon support for amg88xx) Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The same benchmark is running in group C & F, no other tasks are
running, the benchmark is capable to consumed all the CPUs.
We suppose the group C will win more CPU resources since it could
enjoy all the shares of group A, but it's F who wins much more.
The reason is because we have group B with shares as 2, since
A->cfs_rq.load.weight == B->se.load.weight == B->shares/nr_cpus,
so A->cfs_rq.load.weight become very small.
And in calc_group_shares() we calculate shares as:
Since the 'cfs_rq->load.weight' is too small, the load become 0
after scale down, although 'tg_shares' is 102400, shares of the se
which stand for group A on root cfs_rq become 2.
While the se of D on root cfs_rq is far more bigger than 2, so it
wins the battle.
Thus when scale_load_down() scale real weight down to 0, it's no
longer telling the real story, the caller will have the wrong
information and the calculation will be buggy.
This patch add check in scale_load_down(), so the real weight will
be >= MIN_SHARES after scale, after applied the group C wins as
expected.
Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Michael Wang <yun.wang@linux.alibaba.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org> Link: https://lkml.kernel.org/r/38e8e212-59a1-64b2-b247-b6d0b52d8dc1@linux.alibaba.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Enclose the chained handler with chained_irq_{enter,exit}(), so that the
muxed interrupts get properly acked.
This patch also fixes a reboot bug on OX820 SoC, where the jiffies timer
interrupt is never acked. The kernel waits a clock tick forever in
calibrate_delay_converge(), which leads to a boot hang.
Field bdi->io_pages added in commit 9491ae4aade6 ("mm: don't cap request
size based on read-ahead setting") removes unneeded split of read requests.
Stacked drivers do not call blk_queue_max_hw_sectors(). Instead they set
limits of their devices by blk_set_stacking_limits() + disk_stack_limits().
Field bio->io_pages stays zero until user set max_sectors_kb via sysfs.
This patch updates io_pages after merging limits in disk_stack_limits().
Commit c6d6e9b0f6b4 ("dm: do not allow readahead to limit IO size") fixed
the same problem for device-mapper devices, this one fixes MD RAIDs.
Fixes: 9491ae4aade6 ("mm: don't cap request size based on read-ahead setting") Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Bob Liu <bob.liu@oracle.com> Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When SEV or SME is enabled and active, vm_get_page_prot() typically
returns with the encryption bit set. This means that users of
pgprot_modify(, vm_get_page_prot()) (mprotect_fixup(), do_mmap()) end up
with a value of vma->vm_pg_prot that is not consistent with the intended
protection of the PTEs.
This is also important for fault handlers that rely on the VMA
vm_page_prot to set the page protection. Fix this by not allowing
pgprot_modify() to change the encryption bit, similar to how it's done
for PAT bits.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Link: https://lkml.kernel.org/r/20200304114527.3636-2-thomas_os@shipmail.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Bail out early if the xHC host needs to be reset at resume
but driver can't access xHC PCI registers.
If xhci driver already fails to reset the controller then there
is no point in attempting to free, re-initialize, re-allocate and
re-start the host. If failure to access the host is detected later,
failing the resume, xhci interrupts will be double freed
when remove is called.
It will start failing randomly including IO to unrelated zones because of
->error "reuse". Trigger can be partition detection as well if test is not
run immediately which is even more entertaining.
The fix is of course to clear ->error where necessary.
If null_add_dev() fails then null_del_dev() is called with a NULL argument.
Make null_del_dev() handle this scenario correctly. This patch fixes the
following KASAN complaint:
null-ptr-deref in null_del_dev+0x28/0x280 [null_blk]
Read of size 8 at addr 0000000000000000 by task find/1062
SDEI has private events that must be registered on each CPU. When
CPUs come and go they must re-register and re-enable their private
events. Each event has flags to indicate whether this should happen
to protect against an event being registered on a CPU coming online,
while all the others are unregistering the event.
These flags are protected by the sdei_list_lock spinlock, because
the cpuhp callbacks can't take the mutex.
Hibernate needs to unregister all events, but keep the in-memory
re-register and re-enable as they are. sdei_unregister_shared()
takes the spinlock to walk the list, then calls _sdei_event_unregister()
on each shared event. _sdei_event_unregister() tries to take the
same spinlock to update re-register and re-enable. This doesn't go
so well.
Push the re-register and re-enable updates out to their callers.
sdei_unregister_shared() doesn't want these values updated, so
doesn't need to do anything.
This also fixes shared events getting lost over hibernate as this
path made them look unregistered.
Fixes: da351827240e ("firmware: arm_sdei: Add support for CPU and system power states") Reported-by: Liguang Zhang <zhangliguang@linux.alibaba.com> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some older MSM8916 Venus firmware versions also seem to indicate
support for encoding HEVC, even though they really can't.
This will lead to errors later because hfi_session_init() fails
in this case.
HEVC is already ignored for "dec_codecs", so add the same for
"enc_codecs" to make these old firmware versions work correctly.
imx6ul_opp_check_speed_grading is called for both i.MX6UL and i.MX6ULL.
Since the i.MX6ULL was introduced to a separate ocotp compatible node
later, it is possible that the i.MX6ULL has also dtbs with
"fsl,imx6ull-ocotp". On a system without nvmem-cell speed grade a
missing check on this node causes a driver fail without considering
the cpu speed grade.
This patch prevents unwanted cpu overclocking on i.MX6ULL with compatible
node "fsl,imx6ull-ocotp" in old dtbs without nvmem-cell speed grade.
Fixes: 2733fb0d0699 ("cpufreq: imx6q: read OCOTP through nvmem for imx6ul/imx6ull") Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
printk in macro vxge_debug_ll uses __VA_ARGS__ without "##" prefix,
it causes a build error when there is no variable
arguments(e.g. only fmt is specified.).
Signed-off-by: Zheng Wei <wei.zheng@vivo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When doing a 16-bit read that returns data in the MSB byte, the
RSB_DATA register will keep the MSB byte unchanged when doing
the following 8-bit read. sunxi_rsb_read() will then return
a result that contains high byte from 16-bit read mixed with
the 8-bit result.
The consequence is that after this happens the PMIC's regmap will
look like this: (0x33 is the high byte from the 16-bit read)
Fix this by masking the result of the read with the correct mask
based on the size of the read. There are no 16-bit users in the
mainline kernel, so this doesn't need to get into the stable tree.
Signed-off-by: Ondrej Jirman <megous@megous.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
[subject was: drm/msm: shake fist angrily at dma-mapping]
So, using dma_sync_* for our cache needs works out w/ dma iommu ops, but
it falls appart with dma direct ops. The problem is that, depending on
display generation, we can have either set of dma ops (mdp4 and dpu have
iommu wired to mdss node, which maps to toplevel drm device, but mdp5
has iommu wired up to the mdp sub-node within mdss).
Fixes: 0036bc73ccbe (drm/msm: stop abusing dma_map/unmap for cache) Fixes: 449fa54d6815 (dma-direct: correct the physical addr in dma_direct_sync_sg_for_cpu/device) Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Rob Clark <robdclark@chromium.org>
[seanpaul changed subject to something more desriptive] Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190730214633.17820-1-robdclark@gmail.com Cc: nobuhiro1.iwamatsu@toshiba.co.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts
commit 6a4290cc28be1 ("usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.")
We don't yet support any of the OTG mechanisms (HNP/SRP/ADP)
and are not setting gadget->otg_caps, so don't set gadget->is_otg
flag.
If we do then we end up publishing a OTG1.0 descriptor in
the gadget descriptor which causes device enumeration to fail
if we are connected to a host with CONFIG_USB_OTG enabled.
Host side log without this patch
[ 96.720453] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 96.901391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 96.907552] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.060447] usb 1-1: new high-speed USB device number 3 using xhci-hcd
[ 97.241378] usb 1-1: Dual-Role OTG device on non-HNP port
[ 97.247536] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.253606] usb usb1-port1: attempt power cycle
[ 97.960449] usb 1-1: new high-speed USB device number 4 using xhci-hcd
[ 98.141383] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.147540] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.300453] usb 1-1: new high-speed USB device number 5 using xhci-hcd
[ 98.481391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.487545] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.493532] usb usb1-port1: unable to enumerate USB device
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible for the chunk sizes coming from the non RPM remote procs
to not be word aligned. Remove the alignment warning and continue to
read from the FIFO so execution is not stalled.
Signed-off-by: Chris Lew <clew@codeaurora.org> Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__early_cpu_boot_status is of type long. Use quad
assembler directive to allocate proper size.
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Arun KS <arunks@codeaurora.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not quite sure what triggered that, but we really shouldn't be abusing
dma_{map,unmap}_sg() for cache maint.
Cc: Stephen Boyd <sboyd@kernel.org> Tested-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190630124735.27786-1-robdclark@gmail.com Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This lock ordering only happens when bonding is enabled and a certain
bonding related event fires. However, since it can happen this is a global
restriction on lock ordering.
Teach lockdep about the order directly and unconditionally so bugs here
are found quickly.
This appears to be a bug in the design, as it does have lots of locking
that seems like it should allow concurrency. However, when it is all said
and done every single place that uses the cma_exch() scheme is broken, and
all the unlocked reads from the ucma of the cm_id data are wrong too.
syzkaller has been finding endless bugs related to this.
Fixing this in any elegant way is some enormous amount of work. Take a
very big hammer and put a mutex around everything to do with the
ucma_context at the top of every syscall.
syzbot reported that 4fbc0c711b24 ("ceph: remove the extra slashes in
the server path") had caused a regression where an allocation could be
done under a spinlock -- compare_mount_options() is called by sget_fc()
with sb_lock held.
We don't really need the supplied server path, so canonicalize it
in place and compare it directly. To make this work, the leading
slash is kept around and the logic in ceph_real_mount() to skip it
is restored. CEPH_MSG_CLIENT_SESSION now reports the same (i.e.
canonicalized) path, with the leading slash of course.
Fixes: 4fbc0c711b24 ("ceph: remove the extra slashes in the server path") Reported-by: syzbot+98704a51af8e3d9425a9@syzkaller.appspotmail.com Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Luis Henriques <lhenriques@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And then when creating any new file or directory under the mount
point, we can hit the following BUG_ON in ceph_fill_trace():
BUG_ON(ceph_snap(dir) != dvino.snap);
Have the client ignore the extra slashes in the server path when
mounting. This will also canonicalize the path, so that identical mounts
can be consilidated.
Regardless of the internal treatment of these paths, the kernel still
stores the original string including the leading '/' for presentation
to userland.
URL: https://tracker.ceph.com/issues/42771 Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Luis Henriques <lhenriques@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Releasing dd->per_sdma[i].kobject in hfi1_unregister_sysfs().
- This will fix the memory leak.
- Calling kobject_put() to unwind operations only for those entries in
dd->per_sdma[] whose operations have succeeded (including the current
one that has just failed) in hfi1_verbs_register_sysfs().
Cc: <stable@vger.kernel.org> Fixes: 0cb2aa690c7e ("IB/hfi1: Add sysfs interface for affinity setup") Link: https://lore.kernel.org/r/20200326163807.21129.27371.stgit@awfm-01.aw.intel.com Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When kobject_init_and_add() returns an error in the function
hfi1_create_port_files(), the function kobject_put() is not called for the
corresponding kobject, which potentially leads to memory leak.
This patch fixes the issue by calling kobject_put() even if
kobject_init_and_add() fails.
Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200326163813.21129.44280.stgit@awfm-01.aw.intel.com Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the rngc interrupt is masked if the rngc self test fails.
Self test failure means that probe fails as well. Interrupts should be
masked in this case, regardless of the error.
Cc: stable@vger.kernel.org Fixes: 1d5449445bd0 ("hwrng: mx-rngc - add a driver for Freescale RNGC") Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com> Signed-off-by: Martin Kaiser <martin@kaiser.cx> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent change to the netlink code: 6e237d099fac ("netlink: Relax attr
validation for fixed length types") logs a warning when programs send
messages with invalid attributes (e.g., wrong length for a u32). Yafang
reported this error message for tools/accounting/getdelays.c.
send_cmd() is wrongly adding 1 to the attribute length. As noted in
include/uapi/linux/netlink.h nla_len should be NLA_HDRLEN + payload
length, so drop the +1.
When skipping TRBs, we need to account for wrapping around the ring
buffer and not modifying some invalid TRBs. Without this fix, dwc3 won't
be able to check for available TRBs.
It turns out that RDRAND is pretty slow. Comparing these two
constructions:
for (i = 0; i < CHACHA_BLOCK_SIZE; i += sizeof(ret))
arch_get_random_long(&ret);
and
long buf[CHACHA_BLOCK_SIZE / sizeof(long)];
extract_crng((u8 *)buf);
it amortizes out to 352 cycles per long for the top one and 107 cycles
per long for the bottom one, on Coffee Lake Refresh, Intel Core i9-9880H.
And importantly, the top one has the drawback of not benefiting from the
real rng, whereas the bottom one has all the nice benefits of using our
own chacha rng. As get_random_u{32,64} gets used in more places (perhaps
beyond what it was originally intended for when it was introduced as
get_random_{int,long} back in the md5 monstrosity era), it seems like it
might be a good thing to strengthen its posture a tiny bit. Doing this
should only be stronger and not any weaker because that pool is already
initialized with a bunch of rdrand data (when available). This way, we
get the benefits of the hardware rng as well as our own rng.
Another benefit of this is that we no longer hit pitfalls of the recent
stream of AMD bugs in RDRAND. One often used code pattern for various
things is:
do {
val = get_random_u32();
} while (hash_table_contains_key(val));
That recent AMD bug rendered that pattern useless, whereas we're really
very certain that chacha20 output will give pretty distributed numbers,
no matter what.
So, this simplification seems better both from a security perspective
and from a performance perspective.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20200221201037.30231-1-Jason@zx2c4.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The handler for FLOW_ACTION_VLAN_MANGLE ends by returning whatever the
lower-level function that it calls returns. If there are more actions lined
up after this action, those are never offloaded. Fix by only bailing out
when the called function returns an error.
Fixes: a150201a70da ("mlxsw: spectrum: Add support for vlan modify TC action") Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct can_frame contains some padding which is not explicitly zeroed in
slc_bump. This uninitialized data will then be transmitted if the stack
initialization hardening feature is not enabled (CONFIG_INIT_STACK_ALL).
This commit just zeroes the whole struct including the padding.
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com> Fixes: a1044e36e457 ("can: add slcan driver for serial/USB-serial CAN adapters") Reviewed-by: Kees Cook <keescook@chromium.org> Cc: linux-can@vger.kernel.org Cc: netdev@vger.kernel.org Cc: security@kernel.org Cc: wg@grandegger.com Cc: mkl@pengutronix.de Cc: davem@davemloft.net Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9463c4455900 ("net: stmmac: dwmac1000: Clear unused address
entries") cleared the unused mac address entries, but introduced an
out-of bounds mac address register programming bug -- After setting
the secondary unicast mac addresses, the "reg" value has reached
netdev_uc_count() + 1, thus we should only clear address entries
if (addr < perfect_addr_number)
Fixes: 9463c4455900 ("net: stmmac: dwmac1000: Clear unused address entries") Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the power-down bit is cleared, the chip internally triggers a
global reset. According to the KSZ9031 documentation, we have to wait at
least 1ms for the reset to finish.
If the chip is accessed during reset, read will return 0xffff, while
write will be ignored. Depending on the system performance and MDIO bus
speed, we may or may not run in to this issue.
This bug was discovered on an iMX6QP system with KSZ9031 PHY and
attached PHY interrupt line. If IRQ was used, the link status update was
lost. In polling mode, the link status update was always correct.
The investigation showed, that during a read-modify-write access, the
read returned 0xffff (while the chip was still in reset) and
corresponding write hit the chip _after_ reset and triggered (due to the
0xffff) another reset in an undocumented bit (register 0x1f, bit 1),
resulting in the next write being lost due to the new reset cycle.
This patch fixes the issue by adding a 1...2 ms sleep after the
genphy_resume().
Fixes: 836384d2501d ("net: phy: micrel: Add specific suspend") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the bcm_sf2 was converted into a proper platform device driver and
used the new dsa_register_switch() interface, we would still be parsing
the legacy DSA node that contained all the port information since the
platform firmware has intentionally maintained backward and forward
compatibility to client programs. Ensure that we do parse the correct
node, which is "ports" per the revised DSA binding.
Fixes: d9338023fb8e ("net: dsa: bcm_sf2: Make it a real platform device driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were registering our slave MDIO bus with OF and doing so with
assigning the newly created slave_mii_bus of_node to the master MDIO bus
controller node. This is a bad thing to do for a number of reasons:
- we are completely lying about the slave MII bus is arranged and yet we
still want to control which MDIO devices it probes. It was attempted
before to play tricks with the bus_mask to perform that:
https://www.spinics.net/lists/netdev/msg429420.html but the approach
was rightfully rejected
- the device_node reference counting is messed up and we are effectively
doing a double probe on the devices we already probed using the
master, this messes up all resources reference counts (such as clocks)
The proper fix for this as indicated by David in his reply to the
thread above is to use a platform data style registration so as to
control exactly which devices we probe:
https://www.spinics.net/lists/netdev/msg430083.html
By using mdiobus_register(), our slave_mii_bus->phy_mask value is used
as intended, and all the PHY addresses that must be redirected towards
our slave MDIO bus is happening while other addresses get redirected
towards the master MDIO bus.
Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bonding slave and team port devices should not have link-local addresses
automatically added to them, as it can interfere with openvswitch being
able to properly add tc ingress.
Basic reproducer, courtesy of Marcelo:
$ ip link add name bond0 type bond
$ ip link set dev ens2f0np0 master bond0
$ ip link set dev ens2f1np2 master bond0
$ ip link set dev bond0 up
$ ip a s
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc
mq master bond0 state UP group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc
mq master bond0 state DOWN group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
11: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UP group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:53ff:fe2f:ea40/64 scope link
valid_lft forever preferred_lft forever
$ ip a l ens2f0np0
2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc
mq master bond0 state UP group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative
valid_lft forever preferred_lft forever
$ ip a l ens2f1np2
5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc
mq master bond0 state DOWN group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative
valid_lft forever preferred_lft forever
Looks like addrconf_sysctl_addr_gen_mode() bypasses the original "is
this a slave interface?" check added by commit c2edacf80e15, and
results in an address getting added, while w/the proposed patch added,
no address gets added. This simply adds the same gating check to another
code path, and thus should prevent the same devices from erroneously
obtaining an ipv6 link-local address.
Fixes: d35a00b8e33d ("net/ipv6: allow sysctl to change link-local address generation mode") Reported-by: Moshe Levi <moshele@mellanox.com> CC: Stephen Hemminger <stephen@networkplumber.org> CC: Marcelo Ricardo Leitner <mleitner@redhat.com> CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ctags indexing ("make tags" command) throws this warning:
ctags: Warning: include/linux/notifier.h:125:
null expansion of name pattern "\1"
This is the result of DEFINE_PER_CPU() macro expansion. Fix that by
getting rid of line break.
Similar fix was already done in commit 25528213fe9f ("tags: Fix
DEFINE_PER_CPU expansions"), but this one probably wasn't noticed.
Link: http://lkml.kernel.org/r/20181030202808.28027-1-semen.protsenko@linaro.org Fixes: 9c80172b902d ("kernel/SRCU: provide a static initializer") Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
======================================================
WARNING: possible circular locking dependency detected
5.4.0-rc8-padata-cpuhp-v3+ #1 Not tainted
------------------------------------------------------
bash/205 is trying to acquire lock: ffffffff8286bcd0 (cpu_hotplug_lock.rw_sem){++++}, at: padata_set_cpumask+0x2b/0x120
but task is already holding lock: ffff8880001abfa0 (&pinst->lock){+.+.}, at: padata_set_cpumask+0x26/0x120
which lock already depends on the new lock.
padata doesn't take cpu_hotplug_lock and pinst->lock in a consistent
order. Which should be first? CPU hotplug calls into padata with
cpu_hotplug_lock already held, so it should have priority.
Fixes: 6751fb3c0e0c ("padata: Use get_online_cpus/put_online_cpus") Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Eric Biggers <ebiggers@kernel.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: linux-crypto@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the lower and upper bounds when there are multiple TCs and
traffic is on the the same TC on the same device.
The lower bound is represented by 'qoffset' and the upper limit for
hash value is 'qcount + qoffset'. This gives a clean Rx to Tx queue
mapping when there are multiple TCs, as the queue indices for upper TCs
will be offset by 'qoffset'.
v2: Fixed commit description based on comments.
Fixes: 1b837d489e06 ("net: Revoke export for __skb_tx_hash, update it to just be static skb_tx_hash") Fixes: eadec877ce9c ("net: Add support for subordinate traffic classes to netdev_pick_tx") Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the handling of sendmsg() with MSG_WAITALL for userspace to round the
timeout for when a signal occurs up to at least two jiffies as a 1 jiffy
timeout may end up being effectively 0 if jiffies wraps at the wrong time.
Fixes: bc5e3a546d55 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have a system which has an EVGA X99 Classified motherboard. The pin
assignments for the HD Audio controller are not correct under Linux.
Windows 10 works fine and informs me that it's using the Recon3Di
driver, and on Linux, `cat
/sys/class/sound/card0/device/subsystem_{vendor,device}` yields
0x3842
0x1038
This patch adds a corresponding entry to the quirk list.
Some HP Pavilion x2 10 models use an AXP288 for charging and fuel-gauge.
We use a native power_supply / PMIC driver in this case, because on most
models with an AXP288 the ACPI AC / Battery code is either completely
missing or relies on custom / proprietary ACPI OpRegions which Linux
does not implement.
The native drivers mostly work fine, but there are 2 problems:
1. These model uses a Type-C connector for charging which the AXP288 does
not support. As long as a Type-A charger (which uses the USB data pins for
charger type detection) is used everything is fine. But if a Type-C
charger is used (such as the charger shipped with the device) then the
charger is not recognized.
So we end up slowly discharging the device even though a charger is
connected, because we are limiting the current from the charger to 500mA.
To make things worse this happens with the device's official charger.
Looking at the ACPI tables HP has "solved" the problem of the AXP288 not
being able to recognize Type-C chargers by simply always programming the
input-current-limit at 3000mA and relying on a Vhold setting of 4.7V
(normally 4.4V) to limit the current intake if the charger cannot handle
this.
2. If no charger is connected when the machine boots then it boots with the
vbus-path disabled. On other devices this is done when a 5V boost converter
is active to avoid the PMIC trying to charge from the 5V boost output.
This is done when an OTG host cable is inserted and the ID pin on the
micro-B receptacle is pulled low, the ID pin has an ACPI event handler
associated with it which re-enables the vbus-path when the ID pin is pulled
high when the OTG cable is removed. The Type-C connector has no ID pin,
there is no ID pin handler and there appears to be no 5V boost converter,
so we end up not charging because the vbus-path is disabled, until we
unplug the charger which automatically clears the vbus-path disable bit and
then on the second plug-in of the adapter we start charging.
The HP Pavilion x2 10 models with an AXP288 do have mostly working ACPI
AC / Battery code which does not rely on custom / proprietary ACPI
OpRegions. So one possible solution would be to blacklist the AXP288
native power_supply drivers and add the HP Pavilion x2 10 with AXP288
DMI ids to the list of devices which should use the ACPI AC / Battery
code even though they have an AXP288 PMIC. This would require changes to
4 files: drivers/acpi/ac.c, drivers/power/supply/axp288_charger.c,
drivers/acpi/battery.c and drivers/power/supply/axp288_fuel_gauge.c.
Beside needing adding the same DMI matches to 4 different files, this
approach also triggers problem 2. from above, but then when suspended,
during suspend the machine will not wakeup because the vbus path is
disabled by the AML code when not charging, so the Vbus low-to-high
IRQ is not triggered, the CPU never wakes up and the device does not
charge even though the user likely things it is charging, esp. since
the charge status LED is directly coupled to an adapter being plugged
in and does not reflect actual charging.
This could be worked by enabling vbus-path explicitly from say the
axp288_charger driver's suspend handler.
So neither situation is ideal, in both cased we need to explicitly enable
the vbus-path to work around different variants of problem 2 above, this
requires a quirk in the axp288_charger code.
If we go the route of using the ACPI AC / Battery drivers then we need
modifications to 3 other drivers; and we need to partially disable the
axp288_charger code, while at the same time keeping it around to enable
vbus-path on suspend.
OTOH we can copy the hardcoding of 3A input-current-limit (we never touch
Vhold, so that would stay at 4.7V) to the axp288_charger code, which needs
changes regardless, then we concentrate all special handling of this
interesting device model in the axp288_charger code. That is what this
commit does.
Cc: stable@vger.kernel.org BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1791098 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On devices with an AXP288, we need to wakeup from suspend when a charger
is plugged in, so that we can do charger-type detection and so that the
axp288-charger driver, which listens for our extcon events, can configure
the input-current-limit accordingly.
Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BIT() macro definition is not available for the UAPI headers
(moreover, it can be defined differently in the user space); replace
its usage with the _BITUL() macro that is defined in <linux/const.h>.
commit e03327122e2c ("pci_endpoint_test: Add 2 ioctl commands")
uses module parameter 'irqtype' in pci_endpoint_test_set_irq()
to check if IRQ vectors of a particular type (MSI or MSI-X or
LEGACY) is already allocated. However with multi-function devices,
'irqtype' will not correctly reflect the IRQ type of the PCI device.
Fix it here by adding 'irqtype' for each PCI device to show the
IRQ type of a particular PCI device.
Fixes: e03327122e2c ("pci_endpoint_test: Add 2 ioctl commands") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: stable@vger.kernel.org # v4.19+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding more than 10 pci-endpoint-test devices results in
"kobject_add_internal failed for pci-endpoint-test.1 with -EEXIST, don't
try to register things with the same name in the same directory". This
is because commit 2c156ac71c6b ("misc: Add host side PCI driver for PCI
test function device") limited the length of the "name" to 20 characters.
Change the length of the name to 24 in order to support upto 10000
pci-endpoint-test devices.
Fixes: 2c156ac71c6b ("misc: Add host side PCI driver for PCI test function device") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: stable@vger.kernel.org # v4.14+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a MMU is shared between multiple GPUs, all of them need to flush their
TLBs, so a single marker that gets reset on the first flush won't do.
Replace the flush marker with a sequence number, so that it's possible to
check if the TLB is in sync with the current page table state for each GPU.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Guido Günther <agx@sigxcpu.org> Signed-off-by: Robert Beckett <bob.beckett@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Chromebook BIOS' do not export an ACPI LPIT, which is how
Linux finds the residency counter for CPU and SYSTEM low power states,
that is exports in /sys/devices/system/cpu/cpuidle/*residency_us
When these sysfs attributes are missing, check the debugfs attrubte
from the pmc_core driver, which accesses the same counter value.
Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: James Zhu <James.Zhu@amd.com> Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Even though INITRAMFS_SOURCE kconfig option isn't set in most of
defconfigs it is used (set) extensively by various build systems.
Commit f26661e12765 ("initramfs: make initramfs compression choice
non-optional") has changed default compression mode. Previously we
compress initramfs using available compression algorithm. Now
we don't use any compression at all by default.
It significantly increases the image size in case of build system
chooses embedded initramfs. Initially I faced with this issue while
using buildroot.
As of today it's not possible to set preferred compression mode
in target defconfig as this option depends on INITRAMFS_SOURCE
being set. Modification of all build systems either doesn't look
like good option.
Let's instead rewrite initramfs compression mode choices list
the way that "INITRAMFS_COMPRESSION_NONE" will be the last option
in the list. In that case it will be chosen only if all other
options (which implements any compression) are not available.
Shutdown of firmware framebuffer has a bunch of problems. Because
of this the framebuffer region might still be reserved even after
drm_fb_helper_remove_conflicting_pci_framebuffers() returned.
Don't consider pci_request_region() failure for the framebuffer
region as fatal error to workaround this issue.
This fixes a problem found on the MacBookPro 2017 Retina panel:
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec aka LINK_RATE_RBR2
aka 0xc), but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel on Linux <= 5.5. Additionally, commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")'
introduced into Linux 5.6-rc1 will unclamp panel depth to
its full 10 bpc, thereby requiring a eDP bandwidth for all
modes that exceeds the bandwidth available and causes all modes
to fail validation -> No modes for the laptop panel -> failure
to set any mode -> Panel goes dark.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to override reported max link rate to the correct maximum
of 0xc = LINK_RATE_RBR2 to fix the darkness and reduced display
precision.
Please apply for Linux 5.6+ to avoid regressing Apple MBP panel
support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The timeout of identify cmd, which is invoked as part of admin queue
creation, can result in freeing of async event data both in
nvme_rdma_timeout handler and error handling path of
nvme_rdma_configure_admin queue thus causing NULL pointer reference.
Call Trace:
? nvme_rdma_setup_ctrl+0x223/0x800 [nvme_rdma]
nvme_rdma_create_ctrl+0x2ba/0x3f7 [nvme_rdma]
nvmf_dev_write+0xa54/0xcc6 [nvme_fabrics]
__vfs_write+0x1b/0x40
vfs_write+0xb2/0x1b0
ksys_write+0x61/0xd0
__x64_sys_write+0x1a/0x20
do_syscall_64+0x60/0x1e0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reviewed-by: Roland Dreier <roland@purestorage.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Prabhath Sajeepa <psajeepa@purestorage.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Under certain circumstances, depending on the order of addresses on the
interfaces, it could be that sctp_v[46]_get_dst() would return a dst
with a mismatched struct flowi.
For example, if when walking through the bind addresses and the first
one is not a match, it saves the dst as a fallback (added in 410f03831c07), but not the flowi. Then if the next one is also not a
match, the previous dst will be returned but with the flowi information
for the 2nd address, which is wrong.
The fix is to use a locally stored flowi that can be used for such
attempts, and copy it to the parameter only in case it is a possible
match, together with the corresponding dst entry.
The patch updates IPv6 code mostly just to be in sync. Even though the issue
is also present there, it fallback is not expected to work with IPv6.
Fixes: 410f03831c07 ("sctp: add routing output fallback") Reported-by: Jin Meng <meng.a.jin@nokia-sbell.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Tested-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should iterate over the datamsgs to move
all chunks(skbs) to newsk.
The following case cause the bug:
for the trouble SKB, it was in outq->transmitted list
sctp_outq_sack
sctp_check_transmitted
SKB was moved to outq->sacked list
then throw away the sack queue
SKB was deleted from outq->sacked
(but it was held by datamsg at sctp_datamsg_to_asoc
So, sctp_wfree was not called here)
then migrate happened
sctp_for_each_tx_datachunk(
sctp_clear_owner_w);
sctp_assoc_migrate();
sctp_for_each_tx_datachunk(
sctp_set_owner_w);
SKB was not in the outq, and was not changed to newsk
finally
__sctp_outq_teardown
sctp_chunk_put (for another skb)
sctp_datamsg_put
__kfree_skb(msg->frag_list)
sctp_wfree (for SKB)
SKB->sk was still oldsk (skb->sk != asoc->base.sk).
Reported-and-tested-by: syzbot+cea71eec5d6de256d54d@syzkaller.appspotmail.com Signed-off-by: Qiujun Huang <hqjagain@gmail.com> Acked-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when creating a new ipip interface with no local/remote configuration,
the lookup is done with TUNNEL_NO_KEY flag, making it impossible to
match the new interface (only possible match being fallback or metada
case interface); e.g: `ip link add tunl1 type ipip dev eth0`
To fix this case, adding a flag check before the key comparison so we
permit to match an interface with no local/remote config; it also avoids
breaking possible userland tools relying on TUNNEL_NO_KEY flag and
uninitialised key.
context being on my side, I'm creating an extra ipip interface attached
to the physical one, and moving it to a dedicated namespace.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Signed-off-by: William Dauchy <w.dauchy@criteo.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix it by adding a pair of rcu_read_lock/unlock() and use
cond_resched_rcu() to avoid the situation where walking of a large
number of items may prevent scheduling for a long time.
Signed-off-by: Qian Cai <cai@lca.pw> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: 3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: bf02f2ffe59c ("arm64: dts: add LS1043A DPAA FMan support") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N900 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on Nokia N900 with OneNAND manufacturers: Samsung,
Numonyx.
Fixes: a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT") Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com> Tested-by: Merlijn Wajer <merlijn@wizzup.org> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current set minimum voltage of 730000µV seems to be wrong. I don't
know the document which specifies that but the imx6qdl datasheets says
that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed,
lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp).
Fixes: ddec5d1c0047 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM") Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an off-by-one error in strncpy size argument in
tools/perf/util/map.c. The issue is that in:
strncmp(filename, "/system/lib/", 11)
the passed string literal: "/system/lib/" has 12 bytes (without the NULL
byte) and the passed size argument is 11. As a result, the logic won't
match the ending "/" byte and will pass filepaths that are stored in
other directories e.g. "/system/libmalicious/bin" or just
"/system/libmalicious".
This functionality seems to be present only on Android. I assume the
/system/ directory is only writable by the root user, so I don't think
this bug has much (or any) security impact.
Fixes: eca818369996 ("perf tools: Add automatic remapping of Android libraries") Signed-off-by: disconnect3d <dominik.b.czarnota@gmail.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Changbin Du <changbin.du@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: John Keeping <john@metanate.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Lentine <mlentine@google.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Link: http://lore.kernel.org/lkml/20200309104855.3775-1-dominik.b.czarnota@gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building an arm64 defconfig with clang's integrated assembler, this error
occurs:
<instantiation>:2:2: error: unrecognized instruction mnemonic
_ASM_EXTABLE 9999b, 9f
^
arch/arm64/mm/cache.S:50:1: note: while in macro instantiation
user_alt 9f, "dc cvau, x4", "dc civac, x4", 0
^
While GNU as seems fine with case-sensitive macro instantiations, clang
doesn't, so use the actual macro name (_asm_extable) as in the rest of
the file.
Also checked that the generated assembly matches the GCC output.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Fixes: 290622efc76e ("arm64: fix "dc cvau" cache operation on errata-affected core") Link: https://github.com/ClangBuiltLinux/linux/issues/924 Signed-off-by: Ilie Halip <ilie.halip@gmail.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation")
and edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access"), because it
turns out these were only necessary due to buggy hardware. This patch adds
a check for such a buggy hardware to prevent any such mistakes again.
While working further on the KS8851 driver, it came to light that the
KS8851-16MLL is capable of switching bus endianness by a hardware strap,
EESK pin. If this strap is incorrect, the IO accesses require such endian
swapping as is being reverted by this patch. Such swapping also impacts
the performance significantly.
Hence, in addition to removing it, detect that the hardware is broken,
report to user, and fail to bind with such hardware.
Fixes: 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation") Fixes: edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access") Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
