Using GCC_DCD_XO_CLK as the XO clock for SDHCI controller is not correct,
it seems that I somehow made a mistake of passing it instead of the fixed
XO clock.
Fixes: 04b3b72b5b8f ("ARM: dts: qcom: ipq4019: Add SDHCI controller node") Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20230811110150.229966-1-robert.marko@sartura.hr Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If reading the RX capabilities fails the training pattern will be set
wrongly: add error checking for drm_dp_read_dpcd_caps() and return if
anything went wrong with it.
While at it, also add a less critical error check when writing to
clear the ESI0 IRQ vector.
Fixes: f70ac097a2cf ("drm/mediatek: Add MT8195 Embedded DisplayPort driver") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Tested-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com> Reviewed-by: CK Hu <ck.hu@mediatek.com> Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-2-angelogioacchino.delregno@collabora.com/ Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
cq_extra is protected by ->completion_lock, which io_get_sqe() misses.
The bug is harmless as it doesn't happen in real life, requires invalid
SQ index array and racing with submission, and only messes up the
userspace, i.e. stall requests execution but will be cleaned up on
ring destruction.
The smaller of data->shallow_depth and __map_depth(sb, index)
will be used as the maximum range when allocating bits.
For a mmc device (one hw queue, deadline I/O scheduler):
q->nr_requests = sched_tags = 128, so according to the previous
calculation method, dd->async_depth = data->shallow_depth = 96,
and the platform is 64bits with 8 cpus, sched_tags.bitmap_tags.sb.shift=5,
sb.maps[]=32/32/32/32, 32 is smaller than 96, whether it is a read or
a write I/O, tags can be allocated to the maximum range each time,
which has not throttling effect.
In addition, refer to the methods of bfg/kyber I/O scheduler,
limit ratiois are calculated base on sched_tags.bitmap_tags.sb.shift.
This patch can throttle write requests really.
Fixes: 07757588e507 ("block/mq-deadline: Reserve 25% of scheduler tags for synchronous requests") Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/1691061162-22898-1-git-send-email-zhiguo.niu@unisoc.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tracefs or debugfs maybe cause hundreds to thousands of PATH records,
too many PATH records maybe cause soft lockup.
For example:
1. CONFIG_KASAN=y && CONFIG_PREEMPTION=n
2. auditctl -a exit,always -S open -k key
3. sysctl -w kernel.watchdog_thresh=5
4. mkdir /sys/kernel/debug/tracing/instances/test
There may be a soft lockup as follows:
watchdog: BUG: soft lockup - CPU#45 stuck for 7s! [mkdir:15498]
Kernel panic - not syncing: softlockup: hung tasks
Call trace:
dump_backtrace+0x0/0x30c
show_stack+0x20/0x30
dump_stack+0x11c/0x174
panic+0x27c/0x494
watchdog_timer_fn+0x2bc/0x390
__run_hrtimer+0x148/0x4fc
__hrtimer_run_queues+0x154/0x210
hrtimer_interrupt+0x2c4/0x760
arch_timer_handler_phys+0x48/0x60
handle_percpu_devid_irq+0xe0/0x340
__handle_domain_irq+0xbc/0x130
gic_handle_irq+0x78/0x460
el1_irq+0xb8/0x140
__audit_inode_child+0x240/0x7bc
tracefs_create_file+0x1b8/0x2a0
trace_create_file+0x18/0x50
event_create_dir+0x204/0x30c
__trace_add_new_event+0xac/0x100
event_trace_add_tracer+0xa0/0x130
trace_array_create_dir+0x60/0x140
trace_array_create+0x1e0/0x370
instance_mkdir+0x90/0xd0
tracefs_syscall_mkdir+0x68/0xa0
vfs_mkdir+0x21c/0x34c
do_mkdirat+0x1b4/0x1d4
__arm64_sys_mkdirat+0x4c/0x60
el0_svc_common.constprop.0+0xa8/0x240
do_el0_svc+0x8c/0xc0
el0_svc+0x20/0x30
el0_sync_handler+0xb0/0xb4
el0_sync+0x160/0x180
Therefore, we add cond_resched() to __audit_inode_child() to fix it.
Fixes: 5195d8e217a7 ("audit: dynamically allocate audit_names when not enough space is in the names array") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The adreno_is_a20x() and adreno_is_a225() functions rely on the
GPU revision, but such information is retrieved inside adreno_gpu_init(),
which is called afterwards.
Fix this problem by caling adreno_gpu_init() earlier, so that
the GPU information revision is available when adreno_is_a20x()
and adreno_is_a225() run.
There is a upper bound to "catlen" but no lower bound to prevent
negatives. I don't see that this necessarily causes a problem but we
may as well be safe.
Fixes: e114e473771c ("Smack: Simplified Mandatory Access Control Kernel") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 1e7ac595fa46 ("drm/msm/dpu: pass irq to
dpu_encoder_helper_wait_for_irq()") the
dpu_encoder_phys_wb_wait_for_commit_done expects the IRQ index rather
than the IRQ index in phys_enc->intr table, however writeback got the
older invocation in place. This was unnoticed for several releases, but
now it's time to fix it.
Fixes: d7d0e73f7de3 ("drm/msm/dpu: introduce the dpu_encoder_phys_* for writeback") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/550924/ Link: https://lore.kernel.org/r/20230802100426.4184892-2-dmitry.baryshkov@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Apparently no one noticed that mdp5 plane states leak like a sieve
ever since we introduced plane_state->commit refcount a few years ago
in 21a01abbe32a ("drm/atomic: Fix freeing connector/plane state too
early by tracking commits, v3.")
Fix it by using the right helpers.
Fixes: 21a01abbe32a ("drm/atomic: Fix freeing connector/plane state too early by tracking commits, v3.") Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Rob Clark <robdclark@gmail.com> Cc: Abhinav Kumar <quic_abhinavk@quicinc.com> Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Cc: linux-arm-msm@vger.kernel.org Cc: freedreno@lists.freedesktop.org Reported-and-tested-by: dorum@noisolation.com Cc: dorum@noisolation.com Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/551236/ Link: https://lore.kernel.org/r/20230803204521.928582-1-daniel.vetter@ffwll.ch Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The connector type and pixel format are missing for this panel,
add them to prevent various drivers from failing to determine
either of those parameters.
As the temporary buffer is no longer used to store 8-bit grayscale data,
its size can be reduced to the size needed to store the monochrome
bitmap data.
Fixes: 24c6bedefbe71de9 ("drm/repaper: Use format helper for xrgb8888 to monochrome conversion") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220317081830.1211400-6-geert@linux-m68k.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Device core dump add block method adds hardware blocks to dumping queue
with stack behavior which causes the hardware blocks to be printed in
reverse order. Change the addition to dumping queue data structure
from "list_add" to "list_add_tail" for FIFO queue behavior.
Fixes: 98659487b845 ("drm/msm: add support to take dpu snapshot") Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Signed-off-by: Ryan McCann <quic_rmccann@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/546200/ Link: https://lore.kernel.org/r/20230622-devcoredump_patch-v5-1-67e8b66c4723@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Several reasons why 'reconfig_mutex' should be held:
1) rdev_for_each() is not safe to be called without the lock, because
rdev can be removed concurrently.
2) mddev_destroy_serial_pool() and mddev_create_serial_pool() should not
be called concurrently.
3) mddev_suspend() from mddev_destroy/create_serial_pool() should be
protected by the lock.
Fixes: 10c92fca636e ("md-bitmap: create and destroy wb_info_pool with the change of backlog") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20230706083727.608914-3-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Local variable is definied first in the beginning of backlog_store(),
there is no need to define it again.
Fixes: 8c13ab115b57 ("md/bitmap: don't set max_write_behind if there is no write mostly device") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20230706083727.608914-2-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 2ae6aaf76912 ("md/raid10: fix io loss while replacement replace
rdev") reads replacement first to prevent io loss. However, there are same
issue in wait_blocked_dev() and raid10_handle_discard(), too. Fix it by
using dereference_rdev_and_rrdev() to get devices.
Fixes: d30588b2731f ("md/raid10: improve raid10 discard request") Fixes: f2e7e269a752 ("md/raid10: pull the code that wait for blocked dev into one function") Signed-off-by: Li Nan <linan122@huawei.com> Link: https://lore.kernel.org/r/20230701080529.2684932-4-linan666@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Factor out a helper to get 'rdev' and 'replacement' from config->mirrors.
Just to make code cleaner and prepare to fix the bug of io loss while
'replacement' replace 'rdev'.
memalloc_noio_save() is called for the first mddev_suspend(), and
repeated mddev_suspend() only increase 'suspended'. However,
memalloc_noio_restore() is also called for the first mddev_resume(),
which means that memory reclaim will be enabled before the last
mddev_resume() is called, while the array is still suspended.
Fix this problem by restore 'noio_flag' for the last mddev_resume().
Fixes: 78f57ef9d50a ("md: use memalloc scope APIs in mddev_suspend()/mddev_resume()") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20230628012931.88911-3-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Now the type of active_io is atomic. It's used to count how many ios are
in the submitting process and it's added and decreased very time. But it
only needs to check if it's zero when suspending the raid. So we can
switch atomic to percpu to improve the performance.
After switching active_io to percpu type, we use the state of active_io
to judge if the raid device is suspended. And we don't need to wake up
->sb_wait in md_handle_request anymore. It's done in the callback function
which is registered when initing active_io. The argument mddev->suspended
is only used to count how many users are trying to set raid to suspend
state.
Signed-off-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <song@kernel.org>
Stable-dep-of: e24ed04389f9 ("md: restore 'noio_flag' for the last mddev_resume()") Signed-off-by: Sasha Levin <sashal@kernel.org>
This helper function will be used in next patch. It's easy for
understanding.
Signed-off-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <song@kernel.org>
Stable-dep-of: e24ed04389f9 ("md: restore 'noio_flag' for the last mddev_resume()") Signed-off-by: Sasha Levin <sashal@kernel.org>
WARNING: min() should probably be min_t(size_t, size, sizeof(ip))
+ ret = copy_to_user(out, &ip, min((size_t)size, sizeof(ip)));
And other style fixes:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Missing a blank line after declarations
Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Both Luxul's XAP devices (XAP-810 and XAP-1440) are access points that
use a non-default design. They don't include switch but have a single
Ethernet port and BCM54210E PHY connected to the Ethernet controller's
MDIO bus.
Support for those devices regressed due to two changes:
1. Describing MDIO bus with switch
After commit 9fb90ae6cae7 ("ARM: dts: BCM53573: Describe on-SoC BCM53125
rev 4 switch") Linux stopped probing for MDIO devices.
2. Dropping hardcoded BCM54210E delays
In commit fea7fda7f50a ("net: phy: broadcom: Fix RGMII delays
configuration for BCM54210E") support for other PHY modes was added but
that requires a proper "phy-mode" value in DT.
Both above changes are correct (they don't need to be reverted or
anything) but they need this fix for DT data to be correct and for Linux
to work properly.
The DRM DP code has macros for the DP power sequencing commands. Use
them in the anx7625 driver instead of raw numbers.
Fixes: 548b512e144f ("drm/bridge: anx7625: send DPCD command to downstream") Fixes: 27f26359de9b ("drm/bridge: anx7625: Set downstream sink into normal status") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230710090929.1873646-1-wenst@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Visible glitches have been observed when running graphics applications on
Linux under Xen hypervisor. Those observations have been confirmed with
failures from kms_pwrite_crc Intel GPU test that verifies data coherency
of DRM frame buffer objects using hardware CRC checksums calculated by
display controllers, exposed to userspace via debugfs. Affected
processing paths have then been identified with new IGT test variants that
mmap the objects using different methods and caching modes [1].
When running as a Xen PV guest, Linux uses Xen provided PAT configuration
which is different from its native one. In particular, Xen specific PTE
encoding of write-combining caching, likely used by graphics applications,
differs from the Linux default one found among statically defined minimal
set of supported modes. Since Xen defines PTE encoding of the WC mode as
_PAGE_PAT, it no longer belongs to the minimal set, depends on correct
handling of _PAGE_PAT bit, and can be mismatched with write-back caching.
When a user calls mmap() for a DRM buffer object, DRM device specific
.mmap file operation, called from mmap_region(), takes care of setting PTE
encoding bits in a vm_page_prot field of an associated virtual memory area
structure. Unfortunately, _PAGE_PAT bit is not preserved when the vma's
.vm_flags are then applied to .vm_page_prot via vm_set_page_prot(). Bits
to be preserved are determined with _PAGE_CHG_MASK symbol that doesn't
cover _PAGE_PAT. As a consequence, WB caching is requested instead of WC
when running under Xen (also, WP is silently changed to WT, and UC
downgraded to UC_MINUS). When running on bare metal, WC is not affected,
but WP and WT extra modes are unintentionally replaced with WC and UC,
respectively.
WP and WT modes, encoded with _PAGE_PAT bit set, were introduced by commit 281d4078bec3 ("x86: Make page cache mode a real type"). Care was taken
to extend _PAGE_CACHE_MASK symbol with that additional bit, but that
symbol has never been used for identification of bits preserved when
applying page protection flags. Support for all cache modes under Xen,
including the problematic WC mode, was then introduced by commit 47591df50512 ("xen: Support Xen pv-domains using PAT").
The issue needs to be fixed by including _PAGE_PAT bit into a bitmask used
by pgprot_modify() for selecting bits to be preserved. We can do that
either internally to pgprot_modify() (as initially proposed), or by making
_PAGE_PAT a part of _PAGE_CHG_MASK. If we go for the latter then, since
_PAGE_PAT is the same as _PAGE_PSE, we need to note that _HPAGE_CHG_MASK
-- a huge pmds' counterpart of _PAGE_CHG_MASK, introduced by commit c489f1257b8c ("thp: add pmd_modify"), defined as (_PAGE_CHG_MASK |
_PAGE_PSE) -- will no longer differ from _PAGE_CHG_MASK. If such
modification of _PAGE_CHG_MASK was irrelevant to its users then one might
wonder why that new _HPAGE_CHG_MASK symbol was introduced instead of
reusing the existing one with that otherwise irrelevant bit (_PAGE_PSE in
that case) added.
Add _PAGE_PAT to _PAGE_CHG_MASK and _PAGE_PAT_LARGE to _HPAGE_CHG_MASK for
symmetry. Split out common bits from both symbols to a common symbol for
clarity.
[ dhansen: tweak the solution changelog description ]
Currently the write_cache attribute allows enabling the QUEUE_FLAG_WC
flag on devices that never claimed the capability.
Fix that by adding a QUEUE_FLAG_HW_WC flag that is set by
blk_queue_write_cache and guards re-enabling the cache through sysfs.
Note that any rescan that calls blk_queue_write_cache will still
re-enable the write cache as in the current code.
Fixes: 93e9d8e836cb ("block: add ability to flag write back caching on a device") Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20230707094239.107968-3-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
gpu->mmu_context is the MMU context of the last job in the HW queue, which
isn't necessarily the same as the context from the bad job. Dump the MMU
context from the scheduler determined bad submit to make it work as intended.
Fixes: 17e4660ae3d7 ("drm/etnaviv: implement per-process address spaces on MMUv2") Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 71de0a054d0e ("arm64: tegra: Drop serial clock-names and
reset-names") was applied, the HSUART failed to probe and the following
error is seen:
serial-tegra 70006300.serial: Couldn't get the reset
serial-tegra: probe of 70006300.serial failed with error -2
Commit 71de0a054d0e ("arm64: tegra: Drop serial clock-names and
reset-names") is correct because the "reset-names" property is not
needed for 8250 UARTs. However, the "reset-names" is required for the
HSUART and should have been populated as part of commit a63c0cd83720c
("arm64: dts: tegra: smaug: Add Bluetooth node") that enabled the HSUART
for the Pixel C. Fix this by populating the "reset-names" property for
the HSUART on the Pixel C.
Fixes: a63c0cd83720 ("arm64: dts: tegra: smaug: Add Bluetooth node") Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 71de0a054d0e ("arm64: tegra: Drop serial clock-names and
reset-names") was applied, the HSUART failed to probe and the following
error is seen:
serial-tegra 3100000.serial: Couldn't get the reset
serial-tegra: probe of 3100000.serial failed with error -2
Commit 71de0a054d0e ("arm64: tegra: Drop serial clock-names and
reset-names") is correct because the "reset-names" property is not
needed for 8250 UARTs. However, the "reset-names" is required for the
HSUART and should have been populated as part of commit ff578db7b693
("arm64: tegra: Enable UART instance on 40-pin header") that
enabled the HSUART for Jetson AGX Orin. Fix this by populating the
"reset-names" property for the HSUART on Jetson AGX Orin.
This fixes:
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: gpio-sck: False schema does not allow [[3, 21, 0]]
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: gpio-miso: False schema does not allow [[3, 22, 0]]
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: gpio-mosi: False schema does not allow [[3, 23, 0]]
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: 'sck-gpios' is a required property
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: Unevaluated properties are not allowed ('gpio-miso', 'gpio-mosi', 'gpio-sck' were unexpected)
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: pcie@2000: '#address-cells' is a required property
From schema: /lib/python3.10/site-packages/dtschema/schemas/pci/pci-bus.yaml
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: pcie@2000: '#size-cells' is a required property
From schema: /lib/python3.10/site-packages/dtschema/schemas/pci/pci-bus.yaml
Two properties that need to be added later are "device_type" and
"ranges". Adding "device_type" on its own causes a new warning and the
value of "ranges" needs to be determined yet.
Such property simply doesn't exist (is not documented or used anywhere).
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: usb@d000: Unevaluated properties are not allowed ('#usb-cells' was unexpected)
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
On 32-bit architectures comparing a resource against a value larger than
U32_MAX can cause a warning:
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:1344:18: error: result of comparison of constant 4294967296 with expression of type 'resource_size_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
res->start > 0x100000000ull)
~~~~~~~~~~ ^ ~~~~~~~~~~~~~~
As gcc does not warn about this in dead code, add an IS_ENABLED() check at
the start of the function. This will always return success but not actually resize
the BAR on 32-bit architectures without high memory, which is exactly what
we want here, as the driver can fall back to bank switching the VRAM
access.
Fixes: 31b8adab3247 ("drm/amdgpu: require a root bus window above 4GB for BAR resize") Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit b9e8a7d950ff ("firmware: ti_sci: Switch transport to polled
mode during system suspend") aims to resolve issues with tisci
operations during system suspend operation. However, the system may
enter a no_irq stage in various other usage modes, including power-off
and restart. To determine if polling mode is appropriate, use the
system_state instead.
While at this, drop the unused is_suspending state variable and
related helpers.
Fixes: b9e8a7d950ff ("firmware: ti_sci: Switch transport to polled mode during system suspend") Reported-by: Francesco Dolcini <francesco@dolcini.it> Reported-by: Wadim Egorov <w.egorov@phytec.de> Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Verdin AM62 Link: https://lore.kernel.org/r/20230620130329.4120443-1-nm@ti.com Closes: https://lore.kernel.org/all/ZGeHMjlnob2GFyHF@francesco-nb.int.toradex.com/ Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
The generic ADC channel binding is recommended over legacy one, update the
DT to the modern binding. No functional change. For further details, see
commit which adds the generic binding to STM32 ADC binding document:
'664b9879f56e ("dt-bindings: iio: stm32-adc: add generic channel binding")'
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
"make dtbs_check" gives following output :
stm32mp157c-odyssey.dt.yaml: gpu@59000000: 'contiguous-area' does not match
any of the regexes: 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/gpu/vivante,gc.yaml
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Use STM32 ADC generic bindings instead of legacy bindings on
emtrion GmbH Argon boards.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
"make dtbs_check" gives following output :
stm32mp157c-emstamp-argon.dtb: gpu@59000000: 'contiguous-area' does not match
any of the regexes: 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/gpu/vivante,gc.yaml
The commit b2de43136058 ("arm64: dts: qcom: pmk8350: Add peripherals for
pmk8350") for the ADC TM (thermal monitoring device) have used the
compatible string from the vendor kernel ("qcom,adc-tm7"). Use the
proper compatible string that is defined in the upstream kernel
("qcom,spmi-adc-tm5-gen2").
The name of the thermal zone in pmr735b.dtsi (pmr735a-thermal) conflicts
with the thermal zone in pmr735a.dtsi. Rename the thermal zone according
to the chip name.
The name of the thermal zone in pm8350b.dtsi (pm8350c-thermal) conflicts
with the thermal zone in pm8350c.dtsi. Rename the thermal zone according
to the chip name.
The name of the thermal zone in pm8350.dtsi (pm8350c-thermal) conflicts
with the thermal zone in pm8350c.dtsi. Rename the thermal zone according
to the chip name.
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the PDX203&206 DTSIs to better document the hardware.
Diff between 203 and 206:
pm8009_gpios
< "CAM_PWR_LD_EN",
> "NC",
pm8150_gpios
< "NC",
> "G_ASSIST_N",
< "WLC_EN_N", /* GPIO_10 */
> "NC", /* GPIO_10 */
Which is due to 5 II having an additional Google Assistant hardware
button and 1 II having a wireless charger & different camera wiring
to accommodate the additional 3D iToF sensor.
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the PDX203&206 DTSIs to better document the hardware.
sm8250 faces the same problem with its Energy Model as sdm845. The energy
cost of LITTLE cores is reported to be higher than medium or big cores
EM computes the energy with formula:
energy = OPP's cost / maximum cpu capacity * utilization
On v6.4-rc6 we have:
max capacity of CPU0 = 284
capacity of CPU0's OPP(1612800 Hz) = 253
cost of CPU0's OPP(1612800 Hz) = 191704
max capacity of CPU4 = 871
capacity of CPU4's OPP(710400 Hz) = 255
cost of CPU4's OPP(710400 Hz) = 343217
Both OPPs have almost the same compute capacity but the estimated energy
per unit of utilization will be estimated to:
energy CPU0 = 191704 / 284 * 1 = 675
energy CPU4 = 343217 / 871 * 1 = 394
EM estimates that little CPU0 will consume 71% more than medium CPU4 for
the same compute capacity. According to [1], little consumes 25% less than
medium core for Coremark benchmark at those OPPs for the same duration.
Set the dynamic-power-coefficient of CPU0-3 to 105 to fix the energy model
for little CPUs.
Since we're using these two macros to read a value from a register, we
need to use the FIELD_GET instead of the FIELD_PREP macro, otherwise
we're getting wrong values.
drivers/video/fbdev/hyperv_fb.c: In function 'hvfb_getmem':
>> drivers/video/fbdev/hyperv_fb.c:1033:24: error: 'screen_info' undeclared (first use in this function)
1033 | base = screen_info.lfb_base;
| ^~~~~~~~~~~
drivers/video/fbdev/hyperv_fb.c:1033:24: note: each undeclared identifier is reported only once for each function it appears in
>> drivers/gpu/drm/hyperv/hyperv_drm_drv.c:75:54: error: 'screen_info' undeclared (first use in this function)
75 | drm_aperture_remove_conflicting_framebuffers(screen_info.lfb_base,
| ^~~~~~~~~~~
drivers/gpu/drm/hyperv/hyperv_drm_drv.c:75:54: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202307090823.nxnT8Kk5-lkp@intel.com/ Fixes: 81d2393485f0 ("fbdev/hyperv-fb: Do not set struct fb_info.apertures") Fixes: 8b0d13545b09 ("efi: Do not include <linux/screen_info.h> from EFI header") Signed-off-by: Sui Jingfeng <suijingfeng@loongson.cn> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20230709100514.703759-1-suijingfeng@loongson.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
The dquot_mark_dquot_dirty() using dquot references from the inode
should be protected by dquot_srcu. quota_off code takes care to call
synchronize_srcu(&dquot_srcu) to not drop dquot references while they
are used by other users. But dquot_transfer() breaks this assumption.
We call dquot_transfer() to drop the last reference of dquot and add
it to free_dquots, but there may still be other users using the dquot
at this time, as shown in the function graph below:
cpu1 cpu2
_________________|_________________
wb_do_writeback CHOWN(1)
...
ext4_da_update_reserve_space
dquot_claim_block
...
dquot_mark_dquot_dirty // try to dirty old quota
test_bit(DQ_ACTIVE_B, &dquot->dq_flags) // still ACTIVE
if (test_bit(DQ_MOD_B, &dquot->dq_flags))
// test no dirty, wait dq_list_lock
...
dquot_transfer
__dquot_transfer
dqput_all(transfer_from) // rls old dquot
dqput // last dqput
dquot_release
clear_bit(DQ_ACTIVE_B, &dquot->dq_flags)
atomic_dec(&dquot->dq_count)
put_dquot_last(dquot)
list_add_tail(&dquot->dq_free, &free_dquots)
// add the dquot to free_dquots
if (!test_and_set_bit(DQ_MOD_B, &dquot->dq_flags))
add dqi_dirty_list // add released dquot to dirty_list
This can cause various issues, such as dquot being destroyed by
dqcache_shrink_scan() after being added to free_dquots, which can trigger
a UAF in dquot_mark_dquot_dirty(); or after dquot is added to free_dquots
and then to dirty_list, it is added to free_dquots again after
dquot_writeback_dquots() is executed, which causes the free_dquots list to
be corrupted and triggers a UAF when dqcache_shrink_scan() is called for
freeing dquot twice.
As Honza said, we need to fix dquot_transfer() to follow the guarantees
dquot_srcu should provide. But calling synchronize_srcu() directly from
dquot_transfer() is too expensive (and mostly unnecessary). So we add
dquot whose last reference should be dropped to the new global dquot
list releasing_dquots, and then queue work item which would call
synchronize_srcu() and after that perform the final cleanup of all the
dquots on releasing_dquots.
Fixes: 4580b30ea887 ("quota: Do not dirty bad dquots") Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230630110822.3881712-5-libaokun1@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add new helper function dquot_active() to make the code more concise.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230630110822.3881712-4-libaokun1@huawei.com>
Stable-dep-of: dabc8b207566 ("quota: fix dqput() to follow the guarantees dquot_srcu should provide") Signed-off-by: Sasha Levin <sashal@kernel.org>
Now we have a helper function dquot_dirty() to determine if dquot has
DQ_MOD_B bit. dquot_active() can easily be misunderstood as a helper
function to determine if dquot has DQ_ACTIVE_B bit. So we avoid this by
renaming it to inode_quota_active() and later on we will add the helper
function dquot_active() to determine if dquot has DQ_ACTIVE_B bit.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230630110822.3881712-3-libaokun1@huawei.com>
Stable-dep-of: dabc8b207566 ("quota: fix dqput() to follow the guarantees dquot_srcu should provide") Signed-off-by: Sasha Levin <sashal@kernel.org>
Refactor out dquot_write_dquot() to reduce duplicate code.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230630110822.3881712-2-libaokun1@huawei.com>
Stable-dep-of: dabc8b207566 ("quota: fix dqput() to follow the guarantees dquot_srcu should provide") Signed-off-by: Sasha Levin <sashal@kernel.org>
In converting to using the standard u16_fract type, commit [1] made the
obvious mistake and failed to take account of the difference in
numerator and denominator ordering, breaking all uses of the cs43130
codec.
The debug print parameters were swapped in the output and they were
printed as decimal values, both the hardware address and the value.
Update the debug print to print the parameters in correct order, and
use hexadecimal print for both address and value.
Fixes: f38b7cca6d0e ("drm/bridge: tc358764: Add DSI to LVDS bridge driver") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Robert Foss <rfoss@kernel.org> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230615152817.359420-1-marex@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
syzkaller reported null-ptr-deref [0] related to AF_NETROM.
This is another self-accept issue from the strace log. [1]
syz-executor creates an AF_NETROM socket and calls connect(), which
is blocked at that time. Then, sk->sk_state is TCP_SYN_SENT and
sock->state is SS_CONNECTING.
Another thread calls connect() concurrently, which finally fails
with -EINVAL. However, the problem here is the socket state is
reset even while the first connect() is blocked.
As sk->state is TCP_CLOSE and sock->state is SS_UNCONNECTED, the
following listen() succeeds. Then, the first connect() looks up
itself as a listener and puts skb into the queue with skb->sk itself.
As a result, the next accept() gets another FD of itself as 3, and
the first connect() finishes.
Finally, the leader thread close()s all FDs. Since the three FDs
reference the same socket, nr_release() does the cleanup for it
three times, and the remaining accept4() causes the following fault.
HFSC assumes that inner classes have an fsc curve, but it is currently
possible for classes without an fsc curve to become parents. This leads
to bugs including a use-after-free.
Don't allow non-root classes without HFSC_FSC to become parents.
MAC (CGX or RPM) asserts backpressure at TL3 or TL2 node of the egress
hierarchical scheduler tree depending on link level config done. If
there are multiple PFC priorities enabled at a time and for all such
flows to backoff, each priority will have to assert backpressure at
different TL3/TL2 scheduler nodes and these flows will need to submit
egress pkts to these nodes.
Current PFC configuration has an issue where in only one backpressure
scheduler node is being allocated which is resulting in only one PFC
priority to work. This patch fixes this issue.
During PFC TX schedulers free, flag TXSCHQ_FREE_ALL was being set
which caused free up all schedulers other than the PFC schedulers.
This patch fixes that to free only the PFC Tx schedulers.
1. Upon txschq free request, the transmit schedular config in hardware
is not getting reset. This patch adds necessary changes to do the same.
2. Current implementation calls txschq alloc during interface
initialization and in response handler updates the default txschq array.
This creates a problem for htb offload where txsch alloc will be called
for every tc class. This patch addresses the issue by reading txschq
response in mbox caller function instead in the response handler.
3. Current otx2_txschq_stop routine tries to free all txschq nodes
allocated to the interface. This creates a problem for htb offload.
This patch introduces the otx2_txschq_free_one to free txschq in a
given level.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: a9ac2e187795 ("octeontx2-pf: Fix PFC TX scheduler free") Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
