Commit fffe9bee14b0 ("gfs2: Delay withdraw from atomic context")
switched from gfs2_withdraw() to gfs2_withdraw_delayed() in
gfs2_ail_error(), but failed to then check if a delayed withdraw had
occurred. Fix that by adding the missing check in __gfs2_ail_flush(),
where the spin locks are already dropped and a withdraw is possible.
Fixes: fffe9bee14b0 ("gfs2: Delay withdraw from atomic context") Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code works as intended, and the warning could be addressed by using
a memcpy(), but turning the warning off for this file works equally well
and may be easier to merge.
Currently, the UIC_COMMAND_COMPL interrupt is disabled and a wmb() is used
to complete the register write before any following writes.
wmb() ensures the writes complete in that order, but completion doesn't
mean that it isn't stored in a buffer somewhere. The recommendation for
ensuring this bit has taken effect on the device is to perform a read back
to force it to make it all the way to the device. This is documented in
device-io.rst and a talk by Will Deacon on this can be seen over here:
Let's do that to ensure the bit hits the device. Because the wmb()'s
purpose wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Fixes: d75f7fe495cf ("scsi: ufs: reduce the interrupts for power mode change requests") Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Can Guo <quic_cang@quicinc.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-9-181252004586@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, interrupts are cleared and disabled prior to registering the
interrupt. An mb() is used to complete the clear/disable writes before the
interrupt is registered.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring these
bits have taken effect on the device is to perform a read back to force it
to make it all the way to the device. This is documented in device-io.rst
and a talk by Will Deacon on this can be seen over here:
Let's do that to ensure these bits hit the device. Because the mb()'s
purpose wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Fixes: 199ef13cac7d ("scsi: ufs: avoid spurious UFS host controller interrupts") Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Can Guo <quic_cang@quicinc.com> Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-8-181252004586@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, HCLKDIV is written to and then completed with an mb().
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
Let's do that to ensure the bit hits the device. Because the mb()'s purpose
wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Fixes: d90996dae8e4 ("scsi: ufs: Add UFS platform driver for Cadence UFS") Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-6-181252004586@redhat.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the CGC enable bit is written and then an mb() is used to ensure
that completes before continuing.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
Let's do that to ensure the bit hits the device. Because the mb()'s purpose
wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Can Guo <quic_cang@quicinc.com> Fixes: 81c0fc51b7a7 ("ufs-qcom: add support for Qualcomm Technologies Inc platforms") Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-5-181252004586@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the QUNIPRO_SEL bit is written to and then an mb() is used to
ensure that completes before continuing.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
But, there's really no reason to even ensure completion before
continuing. The only requirement here is that this write is ordered to this
endpoint (which readl()/writel() guarantees already). For that reason the
mb() can be dropped altogether without anything forcing completion.
Fixes: f06fcc7155dc ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations") Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-4-181252004586@redhat.com Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On SM8550, depending on the Qunipro, we can run with G5 or G4. For now,
when the major version is 5 or above, we go with G5. Therefore, we need to
specifically tell UFS HC that.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 823150ecf04f ("scsi: ufs: qcom: Perform read back after writing unipro mode") Signed-off-by: Sasha Levin <sashal@kernel.org>
On newer UFS revisions, the register at offset 0xD0 is called,
REG_UFS_PARAM0. Since the existing register, RETRY_TIMER_REG is not used
anywhere, it is safe to use the new name.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com> Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 823150ecf04f ("scsi: ufs: qcom: Perform read back after writing unipro mode") Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently after writing to REG_UFS_SYS1CLK_1US a mb() is used to ensure
that write has gone through to the device.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
Let's do that to ensure the bit hits the device. Because the mb()'s purpose
wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Fixes: f06fcc7155dc ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations") Reviewed-by: Can Guo <quic_cang@quicinc.com> Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-2-181252004586@redhat.com Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the reset bit for the UFS provided reset controller (used by its
phy) is written to, and then a mb() happens to try and ensure that hit the
device. Immediately afterwards a usleep_range() occurs.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
Let's do that to ensure the bit hits the device. By doing so and
guaranteeing the ordering against the immediately following usleep_range(),
the mb() can safely be removed.
Fixes: 81c0fc51b7a7 ("ufs-qcom: add support for Qualcomm Technologies Inc platforms") Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Can Guo <quic_cang@quicinc.com> Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-1-181252004586@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The struct bpf_fib_lookup is supposed to be of size 64. A recent commit 59b418c7063d ("bpf: Add a check for struct bpf_fib_lookup size") added
a static assertion to check this property so that future changes to the
structure will not accidentally break this assumption.
As it immediately turned out, on some 32-bit arm systems, when AEABI=n,
the total size of the structure was equal to 68, see [1]. This happened
because the bpf_fib_lookup structure contains a union of two 16-bit
fields:
union {
__u16 tot_len;
__u16 mtu_result;
};
which was supposed to compile to a 16-bit-aligned 16-bit field. On the
aforementioned setups it was instead both aligned and padded to 32-bits.
Declare this inner union as __attribute__((packed, aligned(2))) such
that it always is of size 2 and is aligned to 16 bits.
clang complains that the temporary string for the name passed into
alloc_workqueue() is too short for its contents:
drivers/net/ethernet/qlogic/qed/qed_main.c:1218:3: error: 'snprintf' will always be truncated; specified size is 16, but format string expands to at least 18 [-Werror,-Wformat-truncation]
There is no need for a temporary buffer, and the actual name of a workqueue
is 32 bytes (WQ_NAME_LEN), so just use the interface as intended to avoid
the truncation.
root_domain::overutilized is only used for EAS(energy aware scheduler)
to decide whether to do load balance or not. It is not used if EAS
not possible.
Currently enqueue_task_fair and task_tick_fair accesses, sometime updates
this field. In update_sd_lb_stats it is updated often. This causes cache
contention due to true sharing and burns a lot of cycles. ::overload and
::overutilized are part of the same cacheline. Updating it often invalidates
the cacheline. That causes access to ::overload to slow down due to
false sharing. Hence add EAS check before accessing/updating this field.
EAS check is optimized at compile time or it is a static branch.
Hence it shouldn't cost much.
With the patch, both enqueue_task_fair and newidle_balance don't show
up as hot routines in perf profile.
aaa8736370db ("x86, relocs: Ignore relocations in .notes section")
... only started ignoring the .notes sections in print_absolute_relocs(),
but the same logic should also by applied in walk_relocs() to avoid
such relocations.
[ mingo: Fixed various typos in the changelog, removed extra curly braces from the code. ]
Currently host relies on CE interrupts to get notified that
the service ready message is ready. This results in timeout
issue if the interrupt is not fired, due to some unknown
reasons. See below logs:
[76321.937866] ath10k_pci 0000:02:00.0: wmi service ready event not received
...
[76322.016738] ath10k_pci 0000:02:00.0: Could not init core: -110
And finally it causes WLAN interface bring up failure.
Change to give it one more chance here by polling CE rings,
before failing directly.
md_do_sync
j = mddev->resync_min
while (j < max_sectors)
sectors = raid10_sync_request(mddev, j, &skipped)
if (!md_bitmap_start_sync(..., &sync_blocks))
// md_bitmap_start_sync set sync_blocks to 0
return sync_blocks + sectors_skippe;
// sectors = 0;
j += sectors;
// j never change
Root cause is that commit 301867b1c168 ("md/raid10: check
slab-out-of-bounds in md_bitmap_get_counter") return early from
md_bitmap_get_counter(), without setting returned blocks.
Fix this problem by always set returned blocks from
md_bitmap_get_counter"(), as it used to be.
Noted that this patch just fix the softlockup problem in kernel, the
case that bitmap size doesn't match array size still need to be fixed.
Fixes: 301867b1c168 ("md/raid10: check slab-out-of-bounds in md_bitmap_get_counter") Reported-and-tested-by: Nigel Croxon <ncroxon@redhat.com> Closes: https://lore.kernel.org/all/71ba5272-ab07-43ba-8232-d2da642acb4e@redhat.com/ Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20240422065824.2516-1-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For cmdq jump command, offset 0 means relative jump and offset 1
means absolute jump. cmdq_pkt_jump() is absolute jump, so fix the
typo of CMDQ_JUMP_RELATIVE in cmdq_pkt_jump().
Fixes: 946f1792d3d7 ("soc: mediatek: cmdq: add jump function") Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20240222154120.16959-2-chunkuang.hu@kernel.org Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a check to make sure that the requested xattr node size is no larger
than the eraseblock minus the cleanmarker.
Unlike the usual inode nodes, the xattr nodes aren't split into parts
and spread across multiple eraseblocks, which means that a xattr node
must not occupy more than one eraseblock. If the requested xattr value is
too large, the xattr node can spill onto the next eraseblock, overwriting
the nodes and causing errors such as:
jffs2: argh. node added in wrong place at 0x0000b050(2)
jffs2: nextblock 0x0000a000, expected at 0000b00c
jffs2: error: (823) do_verify_xattr_datum: node CRC failed at 0x01e050,
read=0xfc892c93, calc=0x000000
jffs2: notice: (823) jffs2_get_inode_nodes: Node header CRC failed
at 0x01e00c. {848f,2fc4,0fef511f,59a3d171}
jffs2: Node at 0x0000000c with length 0x00001044 would run over the
end of the erase block
jffs2: Perhaps the file system was created with the wrong erase size?
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found
at 0x00000010: 0x1044 instead
This breaks the filesystem and can lead to KASAN crashes such as:
BUG: KASAN: slab-out-of-bounds in jffs2_sum_add_kvec+0x125e/0x15d0
Read of size 4 at addr ffff88802c31e914 by task repro/830
CPU: 0 PID: 830 Comm: repro Not tainted 6.9.0-rc3+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS Arch Linux 1.16.3-1-1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xc4/0x620
? __virt_addr_valid+0x308/0x5b0
kasan_report+0xc1/0xf0
? jffs2_sum_add_kvec+0x125e/0x15d0
? jffs2_sum_add_kvec+0x125e/0x15d0
jffs2_sum_add_kvec+0x125e/0x15d0
jffs2_flash_direct_writev+0xa8/0xd0
jffs2_flash_writev+0x9c9/0xef0
? __x64_sys_setxattr+0xc4/0x160
? do_syscall_64+0x69/0x140
? entry_SYSCALL_64_after_hwframe+0x76/0x7e
[...]
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: aa98d7cf59b5 ("[JFFS2][XATTR] XATTR support on JFFS2 (version. 5)") Signed-off-by: Ilya Denisyev <dev@elkcl.ru> Link: https://lore.kernel.org/r/20240412155357.237803-1-dev@elkcl.ru Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The subchannel-type field "st" of s390_cio_stsch and s390_cio_msch
tracepoints is incorrectly filled with the subchannel-enabled SCHIB
value "ena". Fix this by assigning the correct value.
Fixes: d1de8633d96a ("s390 cio: Rewrite trace point class s390_class_schib") Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since sha512_transform_rorx() uses ymm registers, execute vzeroupper
before returning from it. This is necessary to avoid reducing the
performance of SSE code.
Fixes: e01d69cb0195 ("crypto: sha512 - Optimized SHA512 x86_64 assembly routine using AVX instructions.") Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since sha256_transform_rorx() uses ymm registers, execute vzeroupper
before returning from it. This is necessary to avoid reducing the
performance of SSE code.
Fixes: d34a460092d8 ("crypto: sha256 - Optimized sha256 x86_64 routine using AVX2's RORX instructions") Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is not a useful configuration, and there is not much point in saving
a few bytes when only one of the two is enabled, so just remove all
these ifdef checks and rely on of_match_node() and acpi_match_device()
returning NULL when these subsystems are disabled.
__cmpxchg_u8() had been added (initially) for the sake of
drivers/phy/ti/phy-tusb1210.c; the thing is, that drivers is
modular, so we need an export
Fixes: b344d6a83d01 "parisc: add support for cmpxchg on u8 pointers" Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang-14 points out that v_size is always smaller than a 64KB
page size if that is configured by the CPU architecture:
fs/nilfs2/ioctl.c:63:19: error: result of comparison of constant 65536 with expression of type '__u16' (aka 'unsigned short') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (argv->v_size > PAGE_SIZE)
~~~~~~~~~~~~ ^ ~~~~~~~~~
This is ok, so just shut up that warning with a cast.
The 'TAG 66 Packet Format' description is missing the cipher code and
checksum fields that are packed into the message packet. As a result,
the buffer allocated for the packet is 3 bytes too small and
write_tag_66_packet() will write up to 3 bytes past the end of the
buffer.
Fix this by increasing the size of the allocation so the whole packet
will always fit in the buffer.
This fixes the below kasan slab-out-of-bounds bug:
BUG: KASAN: slab-out-of-bounds in ecryptfs_generate_key_packet_set+0x7d6/0xde0
Write of size 1 at addr ffff88800afbb2a5 by task touch/181
The buffer used to transfer data over the mailbox interface is mapped
using the client's device. This is incorrect, as the device performing
the DMA transfer is the mailbox itself. Fix it by using the mailbox
controller device instead.
This requires including the mailbox_controller.h header to dereference
the mbox_chan and mbox_controller structures. The header is not meant to
be included by clients. This could be fixed by extending the client API
with a function to access the controller's device.
Fixes: 4e3d60656a72 ("ARM: bcm2835: Add the Raspberry Pi firmware driver") Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Stefan Wahren <wahrenst@gmx.net> Tested-by: Ivan T. Ivanov <iivanov@suse.de> Link: https://lore.kernel.org/r/20240326195807.15163-3-laurent.pinchart@ideasonboard.com Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In spu2_dump_omd() value of ptr is increased by ciph_key_len
instead of hash_iv_len which could lead to going beyond the
buffer boundaries.
Fix this bug by changing ciph_key_len to hash_iv_len.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
The original mount API conversion inexplicably left out the change
from ->remount_fs to ->reconfigure; do that now.
Fixes: 7ab2fa7693c3 ("vfs: Convert openpromfs to use the new mount API") Signed-off-by: Eric Sandeen <sandeen@redhat.com> Link: https://lore.kernel.org/r/90b968aa-c979-420f-ba37-5acc3391b28f@redhat.com Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
epoll can call out to vfs_poll() with a file pointer that may race with
the last 'fput()'. That would make f_count go down to zero, and while
the ep->mtx locking means that the resulting file pointer tear-down will
be blocked until the poll returns, it means that f_count is already
dead, and any use of it won't actually get a reference to the file any
more: it's dead regardless.
Make sure we have a valid ref on the file pointer before we call down to
vfs_poll() from the epoll routines.
On system where native nvme multipath is configured and iopolicy
is set to numa but the nvme controller numa node id is undefined
or -1 (NUMA_NO_NODE) then avoid calculating node distance for
finding optimal io path. In such case we may access numa distance
table with invalid index and that may potentially refer to incorrect
memory. So this patch ensures that if the nvme controller numa node
id is -1 then instead of calculating node distance for finding optimal
io path, we set the numa node distance of such controller to default 10
(LOCAL_DISTANCE).
... and I think that's actually the important thing here:
- the first page fault is from user space, and triggers the vsyscall
emulation.
- the second page fault is from __do_sys_gettimeofday(), and that should
just have caused the exception that then sets the return value to
-EFAULT
- the third nested page fault is due to _raw_spin_unlock_irqrestore() ->
preempt_schedule() -> trace_sched_switch(), which then causes a BPF
trace program to run, which does that bpf_probe_read_compat(), which
causes that page fault under pagefault_disable().
It's quite the nasty backtrace, and there's a lot going on.
The problem is literally the vsyscall emulation, which sets
current->thread.sig_on_uaccess_err = 1;
and that causes the fixup_exception() code to send the signal *despite* the
exception being caught.
And I think that is in fact completely bogus. It's completely bogus
exactly because it sends that signal even when it *shouldn't* be sent -
like for the BPF user mode trace gathering.
In other words, I think the whole "sig_on_uaccess_err" thing is entirely
broken, because it makes any nested page-faults do all the wrong things.
Now, arguably, I don't think anybody should enable vsyscall emulation any
more, but this test case clearly does.
I think we should just make the "send SIGSEGV" be something that the
vsyscall emulation does on its own, not this broken per-thread state for
something that isn't actually per thread.
The x86 page fault code actually tried to deal with the "incorrect nesting"
by having that:
if (in_interrupt())
return;
which ignores the sig_on_uaccess_err case when it happens in interrupts,
but as shown by this example, these nested page faults do not need to be
about interrupts at all.
IOW, I think the only right thing is to remove that horrendously broken
code.
The attached patch looks like the ObviouslyCorrect(tm) thing to do.
NOTE! This broken code goes back to this commit in 2011:
4fc3490114bb ("x86-64: Set siginfo and context on vsyscall emulation faults")
... and back then the reason was to get all the siginfo details right.
Honestly, I do not for a moment believe that it's worth getting the siginfo
details right here, but part of the commit says:
This fixes issues with UML when vsyscall=emulate.
... and so my patch to remove this garbage will probably break UML in this
situation.
I do not believe that anybody should be running with vsyscall=emulate in
2024 in the first place, much less if you are doing things like UML. But
let's see if somebody screams.
There is a race condition when re-creating a kfd_process for a process.
This has been observed when a process under the debugger executes
exec(3). In this scenario:
- The process executes exec.
- This will eventually release the process's mm, which will cause the
kfd_process object associated with the process to be freed
(kfd_process_free_notifier decrements the reference count to the
kfd_process to 0). This causes kfd_process_ref_release to enqueue
kfd_process_wq_release to the kfd_process_wq.
- The debugger receives the PTRACE_EVENT_EXEC notification, and tries to
re-enable AMDGPU traps (KFD_IOC_DBG_TRAP_ENABLE).
- When handling this request, KFD tries to re-create a kfd_process.
This eventually calls kfd_create_process and kobject_init_and_add.
At this point the call to kobject_init_and_add can fail because the
old kfd_process.kobj has not been freed yet by kfd_process_wq_release.
This patch proposes to avoid this race by making sure to drain
kfd_process_wq before creating a new kfd_process object. This way, we
know that any cleanup task is done executing when we reach
kobject_init_and_add.
Signed-off-by: Lancelot SIX <lancelot.six@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rcu quiescent state is reported in the rcu-read critical section, so
the lockdep warning is triggered.
Fix this by splitting out the inner working of __do_softirq() into a helper
function which takes an argument to distinguish between ksoftirqd task
context and interrupted context and invoke it from the relevant call sites
with the proper context information and use that for the conditional
invocation of rcu_softirq_qs().
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://msgid.link/r/20240410172615.255424-2-krzk@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The codec leaves tie combo jack's sleeve/ring2 to floating status
default. It would cause electric noise while connecting the active
speaker jack during boot or shutdown.
This patch requests a gpio to control the additional jack circuit
to tie the contacts to the ground or floating.
The regulator IRQ helper requires caller to provide pointer to IRQ name
which is kept in memory by caller. All other data passed to the helper
in the regulator_irq_desc structure is copied. This can cause some
confusion and unnecessary complexity.
Make the regulator_irq_helper() to copy also the provided IRQ name
information so caller can discard the name after the call to
regulator_irq_helper() completes.
Currently, the sud_test expects the emulated syscall to return the
emulated syscall number. This assumption only works on architectures
were the syscall calling convention use the same register for syscall
number/syscall return value. This is not the case for RISC-V and thus
the return value must be also emulated using the provided ucontext.
In snd_card_disconnect(), we set card->shutdown flag at the beginning,
call callbacks and do sync for card->power_ref_sleep waiters at the
end. The callback may delete a kctl element, and this can lead to a
deadlock when the device was in the suspended state. Namely:
* A process waits for the power up at snd_power_ref_and_wait() in
snd_ctl_info() or read/write() inside card->controls_rwsem.
* The system gets disconnected meanwhile, and the driver tries to
delete a kctl via snd_ctl_remove*(); it tries to take
card->controls_rwsem again, but this is already locked by the
above. Since the sleeper isn't woken up, this deadlocks.
An easy fix is to wake up sleepers before processing the driver
disconnect callbacks but right after setting the card->shutdown flag.
Then all sleepers will abort immediately, and the code flows again.
So, basically this patch moves the wait_event() call at the right
timing. While we're at it, just to be sure, call wait_event_all()
instead of wait_event(), although we don't use exclusive events on
this queue for now.
The commit 81033c6b584b ("ALSA: core: Warn on empty module")
introduced a WARN_ON() for a NULL module pointer passed at snd_card
object creation, and it also wraps the code around it with '#ifdef
MODULE'. This works in most cases, but the devils are always in
details. "MODULE" is defined when the target code (i.e. the sound
core) is built as a module; but this doesn't mean that the caller is
also built-in or not. Namely, when only the sound core is built-in
(CONFIG_SND=y) while the driver is a module (CONFIG_SND_USB_AUDIO=m),
the passed module pointer is ignored even if it's non-NULL, and
card->module remains as NULL. This would result in the missing module
reference up/down at the device open/close, leading to a race with the
code execution after the module removal.
For addressing the bug, move the assignment of card->module again out
of ifdef. The WARN_ON() is still wrapped with ifdef because the
module can be really NULL when all sound drivers are built-in.
Note that we keep 'ifdef MODULE' for WARN_ON(), otherwise it would
lead to a false-positive NULL module check. Admittedly it won't catch
perfectly, i.e. no check is performed when CONFIG_SND=y. But, it's no
real problem as it's only for debugging, and the condition is pretty
rare.
Fixes: 81033c6b584b ("ALSA: core: Warn on empty module") Reported-by: Xu Yang <xu.yang_2@nxp.com> Closes: https://lore.kernel.org/r/20240520170349.2417900-1-xu.yang_2@nxp.com Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Tested-by: Xu Yang <xu.yang_2@nxp.com> Link: https://lore.kernel.org/r/20240522070442.17786-1-tiwai@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most cases when adding a cluster to the directory index,
they are placed at the end, and in the bitmap, this cluster corresponds
to the last bit. The new directory size is calculated as follows:
data_size = (u64)(bit + 1) << indx->index_bits;
In the case of reusing a non-final cluster from the index,
data_size is calculated incorrectly, resulting in the directory size
differing from the actual size.
A check for cluster reuse has been added, and the size update is skipped.
Fixes: 82cae269cfa95 ("fs/ntfs3: Add initialization of super block") Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When counting and checking hard links in an ntfs file record,
struct MFT_REC {
struct NTFS_RECORD_HEADER rhdr; // 'FILE'
__le16 seq; // 0x10: Sequence number for this record.
>> __le16 hard_links; // 0x12: The number of hard links to record.
__le16 attr_off; // 0x14: Offset to attributes.
...
the ntfs3 driver ignored short names (DOS names), causing the link count
to be reduced by 1 and messages to be output to dmesg.
For Windows, such a situation is a minor error, meaning chkdsk does not report
errors on such a volume, and in the case of using the /f switch, it silently
corrects them, reporting that no errors were found. This does not affect
the consistency of the file system.
Nevertheless, the behavior in the ntfs3 driver is incorrect and
changes the content of the file system. This patch should fix that.
PS: most likely, there has been a confusion of concepts
MFT_REC::hard_links and inode::__i_nlink.
Fixes: 82cae269cfa95 ("fs/ntfs3: Add initialization of super block") Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot has reported a potential hang in nilfs_detach_log_writer() called
during nilfs2 unmount.
Analysis revealed that this is because nilfs_segctor_sync(), which
synchronizes with the log writer thread, can be called after
nilfs_segctor_destroy() terminates that thread, as shown in the call trace
below:
Fix this issue by changing nilfs_segctor_sync() so that the log writer
thread returns normally without synchronizing after it terminates, and by
forcing tasks that are already waiting to complete once after the thread
terminates.
The skipped inode metadata flushout will then be processed together in the
subsequent cleanup work in nilfs_segctor_destroy().
A potential and reproducible race issue has been identified where
nilfs_segctor_sync() would block even after the log writer thread writes a
checkpoint, unless there is an interrupt or other trigger to resume log
writing.
This turned out to be because, depending on the execution timing of the
log writer thread running in parallel, the log writer thread may skip
responding to nilfs_segctor_sync(), which causes a call to schedule()
waiting for completion within nilfs_segctor_sync() to lose the opportunity
to wake up.
The reason why waking up the task waiting in nilfs_segctor_sync() may be
skipped is that updating the request generation issued using a shared
sequence counter and adding an wait queue entry to the request wait queue
to the log writer, are not done atomically. There is a possibility that
log writing and request completion notification by nilfs_segctor_wakeup()
may occur between the two operations, and in that case, the wait queue
entry is not yet visible to nilfs_segctor_wakeup() and the wake-up of
nilfs_segctor_sync() will be carried over until the next request occurs.
Fix this issue by performing these two operations simultaneously within
the lock section of sc_state_lock. Also, following the memory barrier
guidelines for event waiting loops, move the call to set_current_state()
in the same location into the event waiting loop to ensure that a memory
barrier is inserted just before the event condition determination.
Compiling the m68k kernel with support for the ColdFire CPU family fails
with the following error:
In file included from drivers/net/ethernet/smsc/smc91x.c:80:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_reset’:
drivers/net/ethernet/smsc/smc91x.h:160:40: error: implicit declaration of function ‘_swapw’; did you mean ‘swap’? [-Werror=implicit-function-declaration]
160 | #define SMC_outw(lp, v, a, r) writew(_swapw(v), (a) + (r))
| ^~~~~~
drivers/net/ethernet/smsc/smc91x.h:904:25: note: in expansion of macro ‘SMC_outw’
904 | SMC_outw(lp, x, ioaddr, BANK_SELECT); \
| ^~~~~~~~
drivers/net/ethernet/smsc/smc91x.c:250:9: note: in expansion of macro ‘SMC_SELECT_BANK’
250 | SMC_SELECT_BANK(lp, 2);
| ^~~~~~~~~~~~~~~
cc1: some warnings being treated as errors
The function _swapw() was removed in commit d97cf70af097 ("m68k: use
asm-generic/io.h for non-MMU io access functions"), but is still used in
drivers/net/ethernet/smsc/smc91x.h.
Use ioread16be() and iowrite16be() to resolve the error.
Cc: stable@vger.kernel.org Fixes: d97cf70af097 ("m68k: use asm-generic/io.h for non-MMU io access functions") Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240510113054.186648-2-thorsten.blum@toblux.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following -Wformat-security compile warnings adding missing
format arguments:
latency-collector.c: In function ‘show_available’:
latency-collector.c:938:17: warning: format not a string literal and
no format arguments [-Wformat-security]
938 | warnx(no_tracer_msg);
| ^~~~~
latency-collector.c:943:17: warning: format not a string literal and
no format arguments [-Wformat-security]
943 | warnx(no_latency_tr_msg);
| ^~~~~
latency-collector.c: In function ‘find_default_tracer’:
latency-collector.c:986:25: warning: format not a string literal and
no format arguments [-Wformat-security]
986 | errx(EXIT_FAILURE, no_tracer_msg);
|
^~~~
latency-collector.c: In function ‘scan_arguments’:
latency-collector.c:1881:33: warning: format not a string literal and
no format arguments [-Wformat-security]
1881 | errx(EXIT_FAILURE, no_tracer_msg);
| ^~~~
Link: https://lore.kernel.org/linux-trace-kernel/20240404011009.32945-1-skhan@linuxfoundation.org Cc: stable@vger.kernel.org Fixes: e23db805da2df ("tracing/tools: Add the latency-collector to tools directory") Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reader code in rb_get_reader_page() swaps a new reader page into the
ring buffer by doing cmpxchg on old->list.prev->next to point it to the
new page. Following that, if the operation is successful,
old->list.next->prev gets updated too. This means the underlying
doubly-linked list is temporarily inconsistent, page->prev->next or
page->next->prev might not be equal back to page for some page in the
ring buffer.
The resize operation in ring_buffer_resize() can be invoked in parallel.
It calls rb_check_pages() which can detect the described inconsistency
and stop further tracing:
Note that ring_buffer_resize() calls rb_check_pages() only if the parent
trace_buffer has recording disabled. Recent commit d78ab792705c
("tracing: Stop current tracer when resizing buffer") causes that it is
now always the case which makes it more likely to experience this issue.
The window to hit this race is nonetheless very small. To help
reproducing it, one can add a delay loop in rb_get_reader_page():
ret = rb_head_page_replace(reader, cpu_buffer->reader_page);
if (!ret)
goto spin;
for (unsigned i = 0; i < 1U << 26; i++) /* inserted delay loop */
__asm__ __volatile__ ("" : : : "memory");
rb_list_head(reader->list.next)->prev = &cpu_buffer->reader_page->list;
.. and then run the following commands on the target system:
echo 1 > /sys/kernel/tracing/events/sched/sched_switch/enable
while true; do
echo 16 > /sys/kernel/tracing/buffer_size_kb; sleep 0.1
echo 8 > /sys/kernel/tracing/buffer_size_kb; sleep 0.1
done &
while true; do
for i in /sys/kernel/tracing/per_cpu/*; do
timeout 0.1 cat $i/trace_pipe; sleep 0.2
done
done
To fix the problem, make sure ring_buffer_resize() doesn't invoke
rb_check_pages() concurrently with a reader operating on the same
ring_buffer_per_cpu by taking its cpu_buffer->reader_lock.
Link: https://lore.kernel.org/linux-trace-kernel/20240517134008.24529-3-petr.pavlu@suse.com Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Fixes: 659f451ff213 ("ring-buffer: Add integrity check at end of iter read") Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
[ Fixed whitespace ] Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An issue was found on the RTL8125b when transmitting small fragmented
packets, whereby invalid entries were inserted into the transmit ring
buffer, subsequently leading to calls to dma_unmap_single() with a null
address.
This was caused by rtl8169_start_xmit() not noticing changes to nr_frags
which may occur when small packets are padded (to work around hardware
quirks) in rtl8169_tso_csum_v2().
To fix this, postpone inspecting nr_frags until after any padding has been
applied.
Ken reported that RTL8125b can lock up if gro_flush_timeout has the
default value of 20000 and napi_defer_hard_irqs is set to 0.
In this scenario device interrupts aren't disabled, what seems to
trigger some silicon bug under heavy load. I was able to reproduce this
behavior on RTL8168h. Fix this by reverting 7274c4147afb.
Fixes: 7274c4147afb ("r8169: don't try to disable interrupts if NAPI is scheduled already") Cc: stable@vger.kernel.org Reported-by: Ken Milmore <ken.milmore@gmail.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/9b5b6f4c-4f54-4b90-b0b3-8d8023c2e780@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a scenario when resuming from some power saving states
with no_console_suspend where console output can be generated
before the 8250_bcm7271 driver gets the opportunity to restore
the baud_mux_clk frequency. Since the baud_mux_clk is at its
default frequency at this time the output can be garbled until
the driver gets the opportunity to resume.
Since this is only an issue with console use of the serial port
during that window and the console isn't likely to use baud
rates that require alternate baud_mux_clk frequencies, allow the
driver to select the default_mux_rate if it is accurate enough.
The "buf" pointer is an array of u16 values. This code should be
using ARRAY_SIZE() (which is 256) instead of sizeof() (which is 512),
otherwise it can the still got out of bounds.
Fixes: c8d2f34ea96e ("speakup: Avoid crash on very long word") Cc: stable@vger.kernel.org Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Link: https://lore.kernel.org/r/d16f67d2-fd0a-4d45-adac-75ddd11001aa@moroto.mountain Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation uses either gsm0_receive() or gsm1_receive()
depending on whether the user configured the mux in basic or advanced
option mode. Both functions share some state values over the same logical
elements of the frame. However, both frame types differ in their nature.
gsm0_receive() uses non-transparency framing, whereas gsm1_receive() uses
transparency mechanism. Switching between both modes leaves the receive
function in an undefined state when done during frame reception.
Fix this by splitting both states. Add gsm0_receive_state_check_and_fix()
and gsm1_receive_state_check_and_fix() to ensure that gsm->state is reset
after a change of gsm->receive.
Note that gsm->state is only accessed in:
- gsm0_receive()
- gsm1_receive()
- gsm_error()
Assuming the following:
- side A configures the n_gsm in basic option mode
- side B sends the header of a basic option mode frame with data length 1
- side A switches to advanced option mode
- side B sends 2 data bytes which exceeds gsm->len
Reason: gsm->len is not used in advanced option mode.
- side A switches to basic option mode
- side B keeps sending until gsm0_receive() writes past gsm->buf
Reason: Neither gsm->state nor gsm->len have been reset after
reconfiguration.
Fix this by changing gsm->count to gsm->len comparison from equal to less
than. Also add upper limit checks against the constant MAX_MRU in
gsm0_receive() and gsm1_receive() to harden against memory corruption of
gsm->len and gsm->mru.
All other checks remain as we still need to limit the data according to the
user configuration and actual payload size.
When the BIOS configures the architectural TSC-adjust MSRs on secondary
sockets to correct a constant inter-chassis offset, after Linux brings the
cores online, the TSC sync check later resets the core-local MSR to 0,
triggering HPET fallback and leading to performance loss.
Fix this by unconditionally using the initial adjust values read from the
MSRs. Trusting the initial offsets in this architectural mechanism is a
better approach than special-casing workarounds for specific platforms.
kernel_include.py, whose origin is misc.py of docutils, uses reprunicode.
Upstream docutils removed the offending line from the corresponding file
(docutils/docutils/parsers/rst/directives/misc.py) in January 2022.
Quoting the changelog [3]:
Deprecate `nodes.reprunicode` and `nodes.ensure_str()`.
Drop uses of the deprecated constructs (not required with Python 3).
sched_core_share_pid() copies the cookie to userspace with
put_user(id, (u64 __user *)uaddr), expecting 64 bits of space.
The "unsigned long" datatype that is documented in core-scheduling.rst
however is only 32 bits large on 32 bit architectures.
Document "unsigned long long" as the correct data type that is always
64bits large.
This matches what the selftest cs_prctl_test.c has been doing all along.
When asn1_encode_sequence() fails, WARN is not the correct solution.
1. asn1_encode_sequence() is not an internal function (located
in lib/asn1_encode.c).
2. Location is known, which makes the stack trace useless.
3. Results a crash if panic_on_warn is set.
It is also noteworthy that the use of WARN is undocumented, and it
should be avoided unless there is a carefully considered rationale to
use it.
Replace WARN with pr_err, and print the return value instead, which is
only useful piece of information.
Cc: stable@vger.kernel.org # v5.13+ Fixes: f2219745250f ("security: keys: trusted: use ASN.1 TPM2 key format for the blobs") Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IPI buffer location is read from the firmware that we load to the
System Companion Processor, and it's not granted that both the SRAM
(L2TCM) size that is defined in the devicetree node is large enough
for that, and while this is especially true for multi-core SCP, it's
still useful to check on single-core variants as well.
Failing to perform this check may make this driver perform R/W
operations out of the L2TCM boundary, resulting (at best) in a
kernel panic.
To fix that, check that the IPI buffer fits, otherwise return a
failure and refuse to boot the relevant SCP core (or the SCP at
all, if this is single core).
Fixes: 3efa0ea743b7 ("remoteproc/mediatek: read IPI buffer offset from FW") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240321084614.45253-2-angelogioacchino.delregno@collabora.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when kdb is compiled with keyboard support, then we will use
schedule_work() to provoke reset of the keyboard status. Unfortunately
schedule_work() gets called from the kgdboc post-debug-exception
handler. That risks deadlock since schedule_work() is not NMI-safe and,
even on platforms where the NMI is not directly used for debugging, the
debug trap can have NMI-like behaviour depending on where breakpoints
are placed.
Fix this by using the irq work system, which is NMI-safe, to defer the
call to schedule_work() to a point when it is safe to call.
Reported-by: Liuye <liu.yeC@h3c.com> Closes: https://lore.kernel.org/all/20240228025602.3087748-1-liu.yeC@h3c.com/ Cc: stable@vger.kernel.org Reviewed-by: Douglas Anderson <dianders@chromium.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20240424-kgdboc_fix_schedule_work-v2-1-50f5a490aec5@linaro.org Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The type defined for the BINDER_SET_MAX_THREADS ioctl was changed from
size_t to __u32 in order to avoid incompatibility issues between 32 and
64-bit kernels. However, the internal types used to copy from user and
store the value were never updated. Use u32 to fix the inconsistency.
When injecting an exception into a vCPU in Real Mode, suppress the error
code by clearing the flag that tracks whether the error code is valid, not
by clearing the error code itself. The "typo" was introduced by recent
fix for SVM's funky Paged Real Mode.
Opportunistically hoist the logic above the tracepoint so that the trace
is coherent with respect to what is actually injected (this was also the
behavior prior to the buggy commit).
Fixes: b97f07458373 ("KVM: x86: determine if an exception has an error code only when injecting it.") Cc: stable@vger.kernel.org Cc: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230322143300.2209476-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[nsaenz: backport to 5.15.y] Signed-off-by: Nicolas Saenz Julienne <nsaenz@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Sean Christopherson <seanjc@google.com>
syzbot caught another data-race in netlink when
setting sk->sk_err.
Annotate all of them for good measure.
BUG: KCSAN: data-race in netlink_recvmsg / netlink_recvmsg
write to 0xffff8881613bb220 of 4 bytes by task 28147 on cpu 0:
netlink_recvmsg+0x448/0x780 net/netlink/af_netlink.c:1994
sock_recvmsg_nosec net/socket.c:1027 [inline]
sock_recvmsg net/socket.c:1049 [inline]
__sys_recvfrom+0x1f4/0x2e0 net/socket.c:2229
__do_sys_recvfrom net/socket.c:2247 [inline]
__se_sys_recvfrom net/socket.c:2243 [inline]
__x64_sys_recvfrom+0x78/0x90 net/socket.c:2243
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
write to 0xffff8881613bb220 of 4 bytes by task 28146 on cpu 1:
netlink_recvmsg+0x448/0x780 net/netlink/af_netlink.c:1994
sock_recvmsg_nosec net/socket.c:1027 [inline]
sock_recvmsg net/socket.c:1049 [inline]
__sys_recvfrom+0x1f4/0x2e0 net/socket.c:2229
__do_sys_recvfrom net/socket.c:2247 [inline]
__se_sys_recvfrom net/socket.c:2243 [inline]
__x64_sys_recvfrom+0x78/0x90 net/socket.c:2243
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x00000000 -> 0x00000016
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 28146 Comm: syz-executor.0 Not tainted 6.6.0-rc3-syzkaller-00055-g9ed22ae6be81 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/06/2023
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20231003183455.3410550-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: yenchia.chen <yenchia.chen@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported a data-race in data-race in netlink_recvmsg() [1]
Indeed, netlink_recvmsg() can be run concurrently,
and netlink_dump() also needs protection.
[1]
BUG: KCSAN: data-race in netlink_recvmsg / netlink_recvmsg
read to 0xffff888141840b38 of 8 bytes by task 23057 on cpu 0:
netlink_recvmsg+0xea/0x730 net/netlink/af_netlink.c:1988
sock_recvmsg_nosec net/socket.c:1017 [inline]
sock_recvmsg net/socket.c:1038 [inline]
__sys_recvfrom+0x1ee/0x2e0 net/socket.c:2194
__do_sys_recvfrom net/socket.c:2212 [inline]
__se_sys_recvfrom net/socket.c:2208 [inline]
__x64_sys_recvfrom+0x78/0x90 net/socket.c:2208
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
write to 0xffff888141840b38 of 8 bytes by task 23037 on cpu 1:
netlink_recvmsg+0x114/0x730 net/netlink/af_netlink.c:1989
sock_recvmsg_nosec net/socket.c:1017 [inline]
sock_recvmsg net/socket.c:1038 [inline]
____sys_recvmsg+0x156/0x310 net/socket.c:2720
___sys_recvmsg net/socket.c:2762 [inline]
do_recvmmsg+0x2e5/0x710 net/socket.c:2856
__sys_recvmmsg net/socket.c:2935 [inline]
__do_sys_recvmmsg net/socket.c:2958 [inline]
__se_sys_recvmmsg net/socket.c:2951 [inline]
__x64_sys_recvmmsg+0xe2/0x160 net/socket.c:2951
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x0000000000000000 -> 0x0000000000001000
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 23037 Comm: syz-executor.2 Not tainted 6.3.0-rc4-syzkaller-00195-g5a57b48fdfcb #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/02/2023
Fixes: 9063e21fb026 ("netlink: autosize skb lengthes") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230403214643.768555-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: yenchia.chen <yenchia.chen@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we're setting the CRYPTO_TFM_REQ_MAY_BACKLOG flag on our
requests to the crypto API, crypto_aead_{encrypt,decrypt} can return
-EBUSY instead of -EINPROGRESS in valid situations. For example, when
the cryptd queue for AESNI is full (easy to trigger with an
artificially low cryptd.cryptd_max_cpu_qlen), requests will be enqueued
to the backlog but still processed. In that case, the async callback
will also be called twice: first with err == -EINPROGRESS, which it
seems we can just ignore, then with err == 0.
Compared to Sabrina's original patch this version uses the new
tls_*crypt_async_wait() helpers and converts the EBUSY to
EINPROGRESS to avoid having to modify all the error handling
paths. The handling is identical.
Fixes: a54667f6728c ("tls: Add support for encryption using async offload accelerator") Fixes: 94524d8fc965 ("net/tls: Add support for async decryption of tls records") Co-developed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Link: https://lore.kernel.org/netdev/9681d1febfec295449a62300938ed2ae66983f28.1694018970.git.sd@queasysnail.net/ Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[v5.15: fixed contextual merge-conflicts in tls_decrypt_done and tls_encrypt_done] Cc: <stable@vger.kernel.org> # 5.15 Signed-off-by: Shaoying Xu <shaoyi@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The submitting thread (one which called recvmsg/sendmsg)
may exit as soon as the async crypto handler calls complete()
so any code past that point risks touching already freed data.
Try to avoid the locking and extra flags altogether.
Have the main thread hold an extra reference, this way
we can depend solely on the atomic ref counter for
synchronization.
Don't futz with reiniting the completion, either, we are now
tightly controlling when completion fires.
Reported-by: valis <sec@valis.email> Fixes: 0cada33241d9 ("net/tls: fix race condition causing kernel panic") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[v5.15: fixed contextual conflicts in struct tls_sw_context_rx and func
init_ctx_rx; replaced DEBUG_NET_WARN_ON_ONCE with BUILD_BUG_ON_INVALID
since they're equivalent when DEBUG_NET is not defined] Cc: <stable@vger.kernel.org> # 5.15 Signed-off-by: Shaoying Xu <shaoyi@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor out waiting for async encrypt and decrypt to finish.
There are already multiple copies and a subsequent fix will
need more. No functional changes.
Note that crypto_wait_req() returns wait->err
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: aec7961916f3 ("tls: fix race between async notify and socket close")
[v5.15: removed changes in tls_sw_splice_eof and adjusted waiting factor out for
async descrypt in tls_sw_recvmsg] Cc: <stable@vger.kernel.org> # 5.15 Signed-off-by: Shaoying Xu <shaoyi@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we are protected from async completions by decrypt_compl_lock
we can drop the async_notify and reinit the completion before we
start waiting.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: aec7961916f3 ("tls: fix race between async notify and socket close") Signed-off-by: Shaoying Xu <shaoyi@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UMAC_CMD register is written from different execution
contexts and has insufficient synchronization protections to
prevent possible corruption. Of particular concern are the
acceses from the phy_device delayed work context used by the
adjust_link call and the BH context that may be used by the
ndo_set_rx_mode call.
A spinlock is added to the driver to protect contended register
accesses (i.e. reg_lock) and it is used to synchronize accesses
to UMAC_CMD.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Cc: stable@vger.kernel.org Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().
The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.
Fixes: afe3f907d20f ("net: bcmgenet: power on MII block for all MII modes") Cc: stable@vger.kernel.org Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
map_hugetlb.c:18:10: fatal error: vm_util.h: No such file or directory
18 | #include "vm_util.h"
| ^~~~~~~~~~~
compilation terminated.
vm_util.h is not present in 5.15.y, as commit:642bc52aed9c ("selftests:
vm: bring common functions to a new file") is not present in stable
kernels <=6.1.y
'scratch' is never freed. Fix this by calling kfree() in the success, and
in the error case.
Cc: stable@vger.kernel.org # +v5.13 Fixes: f2219745250f ("security: keys: trusted: use ASN.1 TPM2 key format for the blobs") Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original implementation of nfsd used signals to stop threads during
shutdown.
In Linux 2.3.46pre5 nfsd gained the ability to shutdown threads
internally it if was asked to run "0" threads. After this user-space
transitioned to using "rpc.nfsd 0" to stop nfsd and sending signals to
threads was no longer an important part of the API.
In commit 3ebdbe5203a8 ("SUNRPC: discard svo_setup and rename
svc_set_num_threads_sync()") (v5.17-rc1~75^2~41) we finally removed the
use of signals for stopping threads, using kthread_stop() instead.
This patch makes the "obvious" next step and removes the ability to
signal nfsd threads - or any svc threads. nfsd stops allowing signals
and we don't check for their delivery any more.
This will allow for some simplification in later patches.
A change worth noting is in nfsd4_ssc_setup_dul(). There was previously
a signal_pending() check which would only succeed when the thread was
being shut down. It should really have tested kthread_should_stop() as
well. Now it just does the latter, not the former.
Signed-off-by: NeilBrown <neilb@suse.de> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pinctrl_register_one_pin() doesn't check the result of radix_tree_insert()
despite they both may return a negative error code. Linus Walleij said he
has copied the radix tree code from kernel/irq/ where the functions calling
radix_tree_insert() are *void* themselves; I think it makes more sense to
propagate the errors from radix_tree_insert() upstream if we can do that...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
When slice_height is 0, the division by slice_height in the calculation
of the number of slices will cause a division by zero driver crash. This
leaves the kernel in a state that requires a reboot. This patch adds a
check to avoid the division by zero.
The stack trace below is for the 6.8.4 Kernel. I reproduced the issue on
a Z16 Gen 2 Lenovo Thinkpad with a Apple Studio Display monitor
connected via Thunderbolt. The amdgpu driver crashed with this exception
when I rebooted the system with the monitor connected.
After applying this patch, the driver no longer crashes when the monitor
is connected and the system is rebooted. I believe this is the same
issue reported for 3113.
Fixes: 963c555e75b0 ("md: introduce mddev_create/destroy_wb_pool for the change of member device") Signed-off-by: Li Nan <linan122@huawei.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20240208085556.2412922-1-linan666@huaweicloud.com
[ mddev_destroy_serial_pool third parameter was removed in mainline,
where there is no need to suspend within this function anymore. ] Signed-off-by: Jeremy Bongio <jbongio@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The expiry time of a key is unconditionally overwritten during
instantiation, defaulting to turn it permanent. This causes a problem
for DNS resolution as the expiration set by user-space is overwritten to
TIME64_MAX, disabling further DNS updates. Fix this by restoring the
condition that key_set_expiry is only called when the pre-parser sets a
specific expiry.
Fixes: 39299bdd2546 ("keys, dns: Allow key types (eg. DNS) to be reclaimed immediately on expiry") Signed-off-by: Silvio Gissi <sifonsec@amazon.com>
cc: David Howells <dhowells@redhat.com>
cc: Hazem Mohamed Abuelfotoh <abuehaze@amazon.com>
cc: linux-afs@lists.infradead.org
cc: linux-cifs@vger.kernel.org
cc: keyrings@vger.kernel.org
cc: netdev@vger.kernel.org
cc: stable@vger.kernel.org Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit fixed the code that parses the firmware files before
downloading them to the controller but introduced a memory leak in case
the sanity checks ever fail.
Make sure to free the firmware buffer before returning on errors.
Fixes: f905ae0be4b7 ("Bluetooth: qca: add missing firmware sanity checks") Cc: stable@vger.kernel.org # 4.19 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NVM configuration files used by WCN3988 and WCN3990/1/8 have two
sets of configuration tags that are enclosed by a type-length header of
type four which the current parser fails to account for.
Instead the driver happily parses random data as if it were valid tags,
something which can lead to the configuration data being corrupted if it
ever encounters the words 0x0011 or 0x001b.
As is clear from commit b63882549b2b ("Bluetooth: btqca: Fix the NVM
baudrate tag offcet for wcn3991") the intention has always been to
process the configuration data also for WCN3991 and WCN3998 which
encodes the baud rate at a different offset.
Fix the parser so that it can handle the WCN3xxx configuration files,
which has an enclosing type-length header of type four and two sets of
TLV tags enclosed by a type-length header of type two and three,
respectively.
Note that only the first set, which contains the tags the driver is
currently looking for, will be parsed for now.
With the parser fixed, the software in-band sleep bit will now be set
for WCN3991 and WCN3998 (as it is for later controllers) and the default
baud rate 3200000 may be updated by the driver also for WCN3xxx
controllers.
Notably the deep-sleep feature bit is already set by default in all
configuration files in linux-firmware.
Add the missing sanity checks when parsing the firmware files before
downloading them to avoid accessing and corrupting memory beyond the
vmalloced buffer.
Fixes: 83e81961ff7e ("Bluetooth: btqca: Introduce generic QCA ROME support") Cc: stable@vger.kernel.org # 4.10 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator_get() may sometimes be called more than once for the same
consumer device, something which before commit dbe954d8f163 ("regulator:
core: Avoid debugfs: Directory ... already present! error") resulted in
errors being logged.
A couple of recent commits broke the handling of such cases so that
attributes are now erroneously created in the debugfs root directory the
second time a regulator is requested and the log is filled with errors
like:
debugfs: File 'uA_load' in directory '/' already present!
debugfs: File 'min_uV' in directory '/' already present!
debugfs: File 'max_uV' in directory '/' already present!
debugfs: File 'constraint_flags' in directory '/' already present!
on any further calls.
Fixes: 2715bb11cfff ("regulator: core: Fix more error checking for debugfs_create_dir()") Fixes: 08880713ceec ("regulator: core: Streamline debugfs operations") Cc: stable@vger.kernel.org Cc: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20240509133304.8883-1-johan+linaro@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
