This is not a useful configuration, and there is not much point in saving
a few bytes when only one of the two is enabled, so just remove all
these ifdef checks and rely on of_match_node() and acpi_match_device()
returning NULL when these subsystems are disabled.
__cmpxchg_u8() had been added (initially) for the sake of
drivers/phy/ti/phy-tusb1210.c; the thing is, that drivers is
modular, so we need an export
Fixes: b344d6a83d01 "parisc: add support for cmpxchg on u8 pointers" Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang-14 points out that v_size is always smaller than a 64KB
page size if that is configured by the CPU architecture:
fs/nilfs2/ioctl.c:63:19: error: result of comparison of constant 65536 with expression of type '__u16' (aka 'unsigned short') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (argv->v_size > PAGE_SIZE)
~~~~~~~~~~~~ ^ ~~~~~~~~~
This is ok, so just shut up that warning with a cast.
The 'TAG 66 Packet Format' description is missing the cipher code and
checksum fields that are packed into the message packet. As a result,
the buffer allocated for the packet is 3 bytes too small and
write_tag_66_packet() will write up to 3 bytes past the end of the
buffer.
Fix this by increasing the size of the allocation so the whole packet
will always fit in the buffer.
This fixes the below kasan slab-out-of-bounds bug:
BUG: KASAN: slab-out-of-bounds in ecryptfs_generate_key_packet_set+0x7d6/0xde0
Write of size 1 at addr ffff88800afbb2a5 by task touch/181
The buffer used to transfer data over the mailbox interface is mapped
using the client's device. This is incorrect, as the device performing
the DMA transfer is the mailbox itself. Fix it by using the mailbox
controller device instead.
This requires including the mailbox_controller.h header to dereference
the mbox_chan and mbox_controller structures. The header is not meant to
be included by clients. This could be fixed by extending the client API
with a function to access the controller's device.
Fixes: 4e3d60656a72 ("ARM: bcm2835: Add the Raspberry Pi firmware driver") Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Stefan Wahren <wahrenst@gmx.net> Tested-by: Ivan T. Ivanov <iivanov@suse.de> Link: https://lore.kernel.org/r/20240326195807.15163-3-laurent.pinchart@ideasonboard.com Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In spu2_dump_omd() value of ptr is increased by ciph_key_len
instead of hash_iv_len which could lead to going beyond the
buffer boundaries.
Fix this bug by changing ciph_key_len to hash_iv_len.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
The original mount API conversion inexplicably left out the change
from ->remount_fs to ->reconfigure; do that now.
Fixes: 7ab2fa7693c3 ("vfs: Convert openpromfs to use the new mount API") Signed-off-by: Eric Sandeen <sandeen@redhat.com> Link: https://lore.kernel.org/r/90b968aa-c979-420f-ba37-5acc3391b28f@redhat.com Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On system where native nvme multipath is configured and iopolicy
is set to numa but the nvme controller numa node id is undefined
or -1 (NUMA_NO_NODE) then avoid calculating node distance for
finding optimal io path. In such case we may access numa distance
table with invalid index and that may potentially refer to incorrect
memory. So this patch ensures that if the nvme controller numa node
id is -1 then instead of calculating node distance for finding optimal
io path, we set the numa node distance of such controller to default 10
(LOCAL_DISTANCE).
There is a race condition when re-creating a kfd_process for a process.
This has been observed when a process under the debugger executes
exec(3). In this scenario:
- The process executes exec.
- This will eventually release the process's mm, which will cause the
kfd_process object associated with the process to be freed
(kfd_process_free_notifier decrements the reference count to the
kfd_process to 0). This causes kfd_process_ref_release to enqueue
kfd_process_wq_release to the kfd_process_wq.
- The debugger receives the PTRACE_EVENT_EXEC notification, and tries to
re-enable AMDGPU traps (KFD_IOC_DBG_TRAP_ENABLE).
- When handling this request, KFD tries to re-create a kfd_process.
This eventually calls kfd_create_process and kobject_init_and_add.
At this point the call to kobject_init_and_add can fail because the
old kfd_process.kobj has not been freed yet by kfd_process_wq_release.
This patch proposes to avoid this race by making sure to drain
kfd_process_wq before creating a new kfd_process object. This way, we
know that any cleanup task is done executing when we reach
kobject_init_and_add.
Signed-off-by: Lancelot SIX <lancelot.six@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The codec leaves tie combo jack's sleeve/ring2 to floating status
default. It would cause electric noise while connecting the active
speaker jack during boot or shutdown.
This patch requests a gpio to control the additional jack circuit
to tie the contacts to the ground or floating.
Syzbot has reported a potential hang in nilfs_detach_log_writer() called
during nilfs2 unmount.
Analysis revealed that this is because nilfs_segctor_sync(), which
synchronizes with the log writer thread, can be called after
nilfs_segctor_destroy() terminates that thread, as shown in the call trace
below:
Fix this issue by changing nilfs_segctor_sync() so that the log writer
thread returns normally without synchronizing after it terminates, and by
forcing tasks that are already waiting to complete once after the thread
terminates.
The skipped inode metadata flushout will then be processed together in the
subsequent cleanup work in nilfs_segctor_destroy().
A potential and reproducible race issue has been identified where
nilfs_segctor_sync() would block even after the log writer thread writes a
checkpoint, unless there is an interrupt or other trigger to resume log
writing.
This turned out to be because, depending on the execution timing of the
log writer thread running in parallel, the log writer thread may skip
responding to nilfs_segctor_sync(), which causes a call to schedule()
waiting for completion within nilfs_segctor_sync() to lose the opportunity
to wake up.
The reason why waking up the task waiting in nilfs_segctor_sync() may be
skipped is that updating the request generation issued using a shared
sequence counter and adding an wait queue entry to the request wait queue
to the log writer, are not done atomically. There is a possibility that
log writing and request completion notification by nilfs_segctor_wakeup()
may occur between the two operations, and in that case, the wait queue
entry is not yet visible to nilfs_segctor_wakeup() and the wake-up of
nilfs_segctor_sync() will be carried over until the next request occurs.
Fix this issue by performing these two operations simultaneously within
the lock section of sc_state_lock. Also, following the memory barrier
guidelines for event waiting loops, move the call to set_current_state()
in the same location into the event waiting loop to ensure that a memory
barrier is inserted just before the event condition determination.
Compiling the m68k kernel with support for the ColdFire CPU family fails
with the following error:
In file included from drivers/net/ethernet/smsc/smc91x.c:80:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_reset’:
drivers/net/ethernet/smsc/smc91x.h:160:40: error: implicit declaration of function ‘_swapw’; did you mean ‘swap’? [-Werror=implicit-function-declaration]
160 | #define SMC_outw(lp, v, a, r) writew(_swapw(v), (a) + (r))
| ^~~~~~
drivers/net/ethernet/smsc/smc91x.h:904:25: note: in expansion of macro ‘SMC_outw’
904 | SMC_outw(lp, x, ioaddr, BANK_SELECT); \
| ^~~~~~~~
drivers/net/ethernet/smsc/smc91x.c:250:9: note: in expansion of macro ‘SMC_SELECT_BANK’
250 | SMC_SELECT_BANK(lp, 2);
| ^~~~~~~~~~~~~~~
cc1: some warnings being treated as errors
The function _swapw() was removed in commit d97cf70af097 ("m68k: use
asm-generic/io.h for non-MMU io access functions"), but is still used in
drivers/net/ethernet/smsc/smc91x.h.
Use ioread16be() and iowrite16be() to resolve the error.
Cc: stable@vger.kernel.org Fixes: d97cf70af097 ("m68k: use asm-generic/io.h for non-MMU io access functions") Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240510113054.186648-2-thorsten.blum@toblux.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reader code in rb_get_reader_page() swaps a new reader page into the
ring buffer by doing cmpxchg on old->list.prev->next to point it to the
new page. Following that, if the operation is successful,
old->list.next->prev gets updated too. This means the underlying
doubly-linked list is temporarily inconsistent, page->prev->next or
page->next->prev might not be equal back to page for some page in the
ring buffer.
The resize operation in ring_buffer_resize() can be invoked in parallel.
It calls rb_check_pages() which can detect the described inconsistency
and stop further tracing:
Note that ring_buffer_resize() calls rb_check_pages() only if the parent
trace_buffer has recording disabled. Recent commit d78ab792705c
("tracing: Stop current tracer when resizing buffer") causes that it is
now always the case which makes it more likely to experience this issue.
The window to hit this race is nonetheless very small. To help
reproducing it, one can add a delay loop in rb_get_reader_page():
ret = rb_head_page_replace(reader, cpu_buffer->reader_page);
if (!ret)
goto spin;
for (unsigned i = 0; i < 1U << 26; i++) /* inserted delay loop */
__asm__ __volatile__ ("" : : : "memory");
rb_list_head(reader->list.next)->prev = &cpu_buffer->reader_page->list;
.. and then run the following commands on the target system:
echo 1 > /sys/kernel/tracing/events/sched/sched_switch/enable
while true; do
echo 16 > /sys/kernel/tracing/buffer_size_kb; sleep 0.1
echo 8 > /sys/kernel/tracing/buffer_size_kb; sleep 0.1
done &
while true; do
for i in /sys/kernel/tracing/per_cpu/*; do
timeout 0.1 cat $i/trace_pipe; sleep 0.2
done
done
To fix the problem, make sure ring_buffer_resize() doesn't invoke
rb_check_pages() concurrently with a reader operating on the same
ring_buffer_per_cpu by taking its cpu_buffer->reader_lock.
Link: https://lore.kernel.org/linux-trace-kernel/20240517134008.24529-3-petr.pavlu@suse.com Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Fixes: 659f451ff213 ("ring-buffer: Add integrity check at end of iter read") Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
[ Fixed whitespace ] Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "buf" pointer is an array of u16 values. This code should be
using ARRAY_SIZE() (which is 256) instead of sizeof() (which is 512),
otherwise it can the still got out of bounds.
Fixes: c8d2f34ea96e ("speakup: Avoid crash on very long word") Cc: stable@vger.kernel.org Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Link: https://lore.kernel.org/r/d16f67d2-fd0a-4d45-adac-75ddd11001aa@moroto.mountain Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assuming the following:
- side A configures the n_gsm in basic option mode
- side B sends the header of a basic option mode frame with data length 1
- side A switches to advanced option mode
- side B sends 2 data bytes which exceeds gsm->len
Reason: gsm->len is not used in advanced option mode.
- side A switches to basic option mode
- side B keeps sending until gsm0_receive() writes past gsm->buf
Reason: Neither gsm->state nor gsm->len have been reset after
reconfiguration.
Fix this by changing gsm->count to gsm->len comparison from equal to less
than. Also add upper limit checks against the constant MAX_MRU in
gsm0_receive() and gsm1_receive() to harden against memory corruption of
gsm->len and gsm->mru.
All other checks remain as we still need to limit the data according to the
user configuration and actual payload size.
When the BIOS configures the architectural TSC-adjust MSRs on secondary
sockets to correct a constant inter-chassis offset, after Linux brings the
cores online, the TSC sync check later resets the core-local MSR to 0,
triggering HPET fallback and leading to performance loss.
Fix this by unconditionally using the initial adjust values read from the
MSRs. Trusting the initial offsets in this architectural mechanism is a
better approach than special-casing workarounds for specific platforms.
kernel_include.py, whose origin is misc.py of docutils, uses reprunicode.
Upstream docutils removed the offending line from the corresponding file
(docutils/docutils/parsers/rst/directives/misc.py) in January 2022.
Quoting the changelog [3]:
Deprecate `nodes.reprunicode` and `nodes.ensure_str()`.
Drop uses of the deprecated constructs (not required with Python 3).
Currently, when kdb is compiled with keyboard support, then we will use
schedule_work() to provoke reset of the keyboard status. Unfortunately
schedule_work() gets called from the kgdboc post-debug-exception
handler. That risks deadlock since schedule_work() is not NMI-safe and,
even on platforms where the NMI is not directly used for debugging, the
debug trap can have NMI-like behaviour depending on where breakpoints
are placed.
Fix this by using the irq work system, which is NMI-safe, to defer the
call to schedule_work() to a point when it is safe to call.
Reported-by: Liuye <liu.yeC@h3c.com> Closes: https://lore.kernel.org/all/20240228025602.3087748-1-liu.yeC@h3c.com/ Cc: stable@vger.kernel.org Reviewed-by: Douglas Anderson <dianders@chromium.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20240424-kgdboc_fix_schedule_work-v2-1-50f5a490aec5@linaro.org Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing reset domains descriptors by the index upon the SCMI drivers
requests through the SCMI reset operations interface can potentially
lead to out-of-bound violations if the SCMI driver misbehave.
Add an internal consistency check before any such domains descriptors
accesses.
Reported-by: Robert Morris <rtm@csail.mit.edu> Cc: stable@vger.kernel.org Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com>
[Guru: Removed changes to cached_dir.c and checking return value
of smb2_parse_contexts in smb2ops.c] Signed-off-by: Guruswamy Basavaiah <guruswamy.basavaiah@broadcom.com>
[v5.4: Fixed merge-conflicts in smb2_parse_contexts for
missing parameter POSIX response] Signed-off-by: Shaoying Xu <shaoyi@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UMAC_CMD register is written from different execution
contexts and has insufficient synchronization protections to
prevent possible corruption. Of particular concern are the
acceses from the phy_device delayed work context used by the
adjust_link call and the BH context that may be used by the
ndo_set_rx_mode call.
A spinlock is added to the driver to protect contended register
accesses (i.e. reg_lock) and it is used to synchronize accesses
to UMAC_CMD.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Cc: stable@vger.kernel.org Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ndo_set_rx_mode function is synchronized with the
netif_addr_lock spinlock and BHs disabled. Since this
function is also invoked directly from the driver the
same synchronization should be applied.
Fixes: 72f96347628e ("net: bcmgenet: set Rx mode before starting netif") Cc: stable@vger.kernel.org Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().
The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.
Fixes: afe3f907d20f ("net: bcmgenet: power on MII block for all MII modes") Cc: stable@vger.kernel.org Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As noted in commit 28c2d1a7a0bf ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked at least 5
cycles while the sw_reset is asserted to ensure a clean reset.
That commit enabled local loopback to provide an Rx clock from the
GENET sourced Tx clk. However, when connected in MII mode the Tx
clk is sourced by the PHY so if an EPHY is not supplying clocks
(e.g. when the link is down) the UniMAC does not receive the
necessary clocks.
This commit extends the sw_reset window until the PHY reports that
the link is up thereby ensuring that the clocks are being provided
to the MAC to produce a clean reset.
One consequence is that if the system attempts to enter a Wake on
LAN suspend state when the PHY link has not been active the MAC
may not have had a chance to initialize cleanly. In this case, we
remove the sw_reset and enable the WoL reception path as normal
with the hope that the PHY will provide the necessary clocks to
drive the WoL blocks if the link becomes active after the system
has entered suspend.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is not a good solution when connecting to an external switch
that may not support the isolation of the TXC signal resulting in
output driver contention on the pin.
A different solution is necessary.
Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[Adjusted to accommodate lack of commit 4f8d81b77e66] Signed-off-by: Doug Berger <opendmb@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
map_hugetlb.c:18:10: fatal error: vm_util.h: No such file or directory
18 | #include "vm_util.h"
| ^~~~~~~~~~~
compilation terminated.
vm_util.h is not present in 5.4.y, as commit:642bc52aed9c ("selftests:
vm: bring common functions to a new file") is not present in stable
kernels <=6.1.y
In the ext4_valid_extent_entries function,
if prev is 0, no error is returned even if lblock<=prev.
This was intended to skip the check on the first extent, but
in the error image above, prev=0+1-1=0 when checking the second extent,
so even though lblock<=prev, the function does not return an error.
As a result, bug_ON occurs in __es_tree_search and the system panics.
To solve this problem, we only need to check that:
1. The lblock of the first extent is not less than 0.
2. The lblock of the next extent is not less than
the next block of the previous extent.
The same applies to extent_idx.
Cc: stable@kernel.org Fixes: 5946d089379a ("ext4: check for overlapping extents in ext4_valid_extent_entries()") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220518120816.1541863-1-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reported-by: syzbot+2a58d88f0fb315c85363@syzkaller.appspotmail.com
[gpiccoli: Manual backport due to unrelated missing patches.] Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pinctrl_register_one_pin() doesn't check the result of radix_tree_insert()
despite they both may return a negative error code. Linus Walleij said he
has copied the radix tree code from kernel/irq/ where the functions calling
radix_tree_insert() are *void* themselves; I think it makes more sense to
propagate the errors from radix_tree_insert() upstream if we can do that...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
In the generic pin config library, readback of some options are handled
differently compared to the setting of those options: the argument value
is used to convey enable/disable of an option in the set path, but
success or -EINVAL is used to convey if an option is enabled or disabled
in the debugfs readback path.
PIN_CONFIG_INPUT_SCHMITT_ENABLE is one such option. Fix the readback of
the option in the mediatek-paris library, so that the debugfs dump is
not showing "input schmitt enabled" for pins that don't have it enabled.
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c: In function mtk_hw_pin_field_lookup:
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c:70:39: warning:
variable e set but not used [-Wunused-but-set-variable]
Since commit 3de7deefce69 ("pinctrl: mediatek: Check gpio pin
number and use binary search in mtk_hw_pin_field_lookup()"),
it is not used any more, so remove it, also remove redundant
assignment to variable c, it will be assigned a new value later
before used.
Some pin doesn't support PUPD register, if it fails and fallbacks with
bias_set_combo case, it will call mtk_pinconf_bias_set_pupd_r1_r0() to
modify the PUPD pin again.
Since the general bias set are either PU/PD or PULLSEL/PULLEN, try
bias_set or bias_set_rev1 for the other fallback case. If the pin
doesn't support neither PU/PD nor PULLSEL/PULLEN, it will return
-ENOTSUPP.
regulator_get() may sometimes be called more than once for the same
consumer device, something which before commit dbe954d8f163 ("regulator:
core: Avoid debugfs: Directory ... already present! error") resulted in
errors being logged.
A couple of recent commits broke the handling of such cases so that
attributes are now erroneously created in the debugfs root directory the
second time a regulator is requested and the log is filled with errors
like:
debugfs: File 'uA_load' in directory '/' already present!
debugfs: File 'min_uV' in directory '/' already present!
debugfs: File 'max_uV' in directory '/' already present!
debugfs: File 'constraint_flags' in directory '/' already present!
on any further calls.
Fixes: 2715bb11cfff ("regulator: core: Fix more error checking for debugfs_create_dir()") Fixes: 08880713ceec ("regulator: core: Streamline debugfs operations") Cc: stable@vger.kernel.org Cc: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20240509133304.8883-1-johan+linaro@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net_alloc_generic is called by net_alloc, which is called without any
locking. It reads max_gen_ptrs, which is changed under pernet_ops_rwsem. It
is read twice, first to allocate an array, then to set s.len, which is
later used to limit the bounds of the array access.
It is possible that the array is allocated and another thread is
registering a new pernet ops, increments max_gen_ptrs, which is then used
to set s.len with a larger than allocated length for the variable array.
Fix it by reading max_gen_ptrs only once in net_alloc_generic. If
max_gen_ptrs is later incremented, it will be caught in net_assign_generic.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Fixes: 073862ba5d24 ("netns: fix net_alloc_generic()") Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240502132006.3430840-1-cascardo@igalia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correctly set the length of the drm_event to the size of the structure
that's actually used.
The length of the drm_event was set to the parent structure instead of
to the drm_vmw_event_fence which is supposed to be read. drm_read
uses the length parameter to copy the event to the user space thus
resuling in oob reads.
Sam Page (sam4k) working with Trend Micro Zero Day Initiative reported
a UAF in the tipc_buf_append() error path:
BUG: KASAN: slab-use-after-free in kfree_skb_list_reason+0x47e/0x4c0
linux/net/core/skbuff.c:1183
Read of size 8 at addr ffff88804d2a7c80 by task poc/8034
In the critical scenario, either the relevant skb is freed or its
ownership is transferred into a frag_lists. In both cases, the cleanup
code must not free it again: we need to clear the skb reference earlier.
Fixes: 1149557d64c9 ("tipc: eliminate unnecessary linearization of incoming buffers") Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-23852 Acked-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/752f1ccf762223d109845365d07f55414058e5a3.1714484273.git.pabeni@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the USB driver passes a pointer into the TRB buffer for creq, this
buffer can be overwritten with the status response as soon as the event
is queued. This can make the final check return USB_GADGET_DELAYED_STATUS
when it shouldn't. Instead use the stored wLength.
The OS descriptors logic had the high/low byte of w_value inverted, causing
the extended properties to not be accessible for interface != 0.
>From the Microsoft documentation:
https://learn.microsoft.com/en-us/windows-hardware/drivers/usbcon/microsoft-os-1-0-descriptors-specification
OS_Desc_CompatID.doc (w_index = 0x4):
- wValue:
High Byte = InterfaceNumber. InterfaceNumber is set to the number of the
interface or function that is associated with the descriptor, typically
0x00. Because a device can have only one extended compat ID descriptor,
it should ignore InterfaceNumber, regardless of the value, and simply
return the descriptor.
Low Byte = 0. PageNumber is used to retrieve descriptors that are larger
than 64 KB. The header section is 16 bytes, so PageNumber is set to 0 for
this request.
We currently do not support >64KB compat ID descriptors, so verify that the
low byte is 0.
OS_Desc_Ext_Prop.doc (w_index = 0x5):
- wValue:
High byte = InterfaceNumber. The high byte of wValue is set to the number
of the interface or function that is associated with the descriptor.
Low byte = PageNumber. The low byte of wValue is used to retrieve
descriptors that are larger than 64 KB. The header section is 10 bytes, so
PageNumber is set to 0 for this request.
We also don't support >64KB extended properties, so verify that the low byte
is 0 and use the high byte for the interface number.
Ensure that packet_buffer_get respects the user_length provided. If
the length of the head packet exceeds the user_length, packet_buffer_get
will now return 0 to signify to the user that no data were read
and a larger buffer size is required. Helps prevent user space overflows.
In qede_add_tc_flower_fltr(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced these functions.
Only compile tested.
Fixes: 2ce9c93eaca6 ("qede: Ingress tc flower offload (drop action) support.") Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Explicitly set 'rc' (return code), before jumping to the
unlock and return path.
By not having any code depend on that 'rc' remains at
it's initial value of -EINVAL, then we can re-use 'rc' for
the return code of function calls in subsequent patches.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fcee2065a178 ("net: qede: use return from qede_parse_flow_attr() for flower")
[ resolved conflict in v5.4, no extack for qede_parse_actions() yet ] Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The change from skb_copy to pskb_copy unfortunately changed the data
copying to omit the ethernet header, since it was pulled before reaching
this point. Fix this by calling __skb_push/pull around pskb_copy.
Fixes: 59c878cbcdd8 ("net: bridge: fix multicast-to-unicast with fraglist GSO") Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Each attribute inside a nested IFLA_VF_VLAN_LIST is assumed to be a
struct ifla_vf_vlan_info so the size of such attribute needs to be at least
of sizeof(struct ifla_vf_vlan_info) which is 14 bytes.
The current size validation in do_setvfinfo is against NLA_HDRLEN (4 bytes)
which is less than sizeof(struct ifla_vf_vlan_info) so this validation
is not enough and a too small attribute might be cast to a
struct ifla_vf_vlan_info, this might result in an out of bands
read access when accessing the saved (casted) entry in ivvl.
Fixes: 79aab093a0b5 ("net: Update API for VF vlan protocol 802.1ad support") Signed-off-by: Roded Zats <rzats@paloaltonetworks.com> Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Link: https://lore.kernel.org/r/20240502155751.75705-1-rzats@paloaltonetworks.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a race condition between l2cap_chan_timeout() and
l2cap_chan_del(). When we use l2cap_chan_del() to delete the
channel, the chan->conn will be set to null. But the conn could
be dereferenced again in the mutex_lock() of l2cap_chan_timeout().
As a result the null pointer dereference bug will happen. The
KASAN report triggered by POC is shown below:
When the sco connection is established and then, the sco socket
is releasing, timeout_work will be scheduled to judge whether
the sco disconnection is timeout. The sock will be deallocated
later, but it is dereferenced again in sco_sock_timeout. As a
result, the use-after-free bugs will happen. The root cause is
shown below:
[ 95.890016] ==================================================================
[ 95.890496] BUG: KASAN: slab-use-after-free in sco_sock_timeout+0x5e/0x1c0
[ 95.890755] Write of size 4 at addr ffff88800c388080 by task kworker/0:0/7
...
[ 95.890755] Workqueue: events sco_sock_timeout
[ 95.890755] Call Trace:
[ 95.890755] <TASK>
[ 95.890755] dump_stack_lvl+0x45/0x110
[ 95.890755] print_address_description+0x78/0x390
[ 95.890755] print_report+0x11b/0x250
[ 95.890755] ? __virt_addr_valid+0xbe/0xf0
[ 95.890755] ? sco_sock_timeout+0x5e/0x1c0
[ 95.890755] kasan_report+0x139/0x170
[ 95.890755] ? update_load_avg+0xe5/0x9f0
[ 95.890755] ? sco_sock_timeout+0x5e/0x1c0
[ 95.890755] kasan_check_range+0x2c3/0x2e0
[ 95.890755] sco_sock_timeout+0x5e/0x1c0
[ 95.890755] process_one_work+0x561/0xc50
[ 95.890755] worker_thread+0xab2/0x13c0
[ 95.890755] ? pr_cont_work+0x490/0x490
[ 95.890755] kthread+0x279/0x300
[ 95.890755] ? pr_cont_work+0x490/0x490
[ 95.890755] ? kthread_blkcg+0xa0/0xa0
[ 95.890755] ret_from_fork+0x34/0x60
[ 95.890755] ? kthread_blkcg+0xa0/0xa0
[ 95.890755] ret_from_fork_asm+0x11/0x20
[ 95.890755] </TASK>
[ 95.890755]
[ 95.890755] Allocated by task 506:
[ 95.890755] kasan_save_track+0x3f/0x70
[ 95.890755] __kasan_kmalloc+0x86/0x90
[ 95.890755] __kmalloc+0x17f/0x360
[ 95.890755] sk_prot_alloc+0xe1/0x1a0
[ 95.890755] sk_alloc+0x31/0x4e0
[ 95.890755] bt_sock_alloc+0x2b/0x2a0
[ 95.890755] sco_sock_create+0xad/0x320
[ 95.890755] bt_sock_create+0x145/0x320
[ 95.890755] __sock_create+0x2e1/0x650
[ 95.890755] __sys_socket+0xd0/0x280
[ 95.890755] __x64_sys_socket+0x75/0x80
[ 95.890755] do_syscall_64+0xc4/0x1b0
[ 95.890755] entry_SYSCALL_64_after_hwframe+0x67/0x6f
[ 95.890755]
[ 95.890755] Freed by task 506:
[ 95.890755] kasan_save_track+0x3f/0x70
[ 95.890755] kasan_save_free_info+0x40/0x50
[ 95.890755] poison_slab_object+0x118/0x180
[ 95.890755] __kasan_slab_free+0x12/0x30
[ 95.890755] kfree+0xb2/0x240
[ 95.890755] __sk_destruct+0x317/0x410
[ 95.890755] sco_sock_release+0x232/0x280
[ 95.890755] sock_close+0xb2/0x210
[ 95.890755] __fput+0x37f/0x770
[ 95.890755] task_work_run+0x1ae/0x210
[ 95.890755] get_signal+0xe17/0xf70
[ 95.890755] arch_do_signal_or_restart+0x3f/0x520
[ 95.890755] syscall_exit_to_user_mode+0x55/0x120
[ 95.890755] do_syscall_64+0xd1/0x1b0
[ 95.890755] entry_SYSCALL_64_after_hwframe+0x67/0x6f
[ 95.890755]
[ 95.890755] The buggy address belongs to the object at ffff88800c388000
[ 95.890755] which belongs to the cache kmalloc-1k of size 1024
[ 95.890755] The buggy address is located 128 bytes inside of
[ 95.890755] freed 1024-byte region [ffff88800c388000, ffff88800c388400)
[ 95.890755]
[ 95.890755] The buggy address belongs to the physical page:
[ 95.890755] page: refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff88800c38a800 pfn:0xc388
[ 95.890755] head: order:3 entire_mapcount:0 nr_pages_mapped:0 pincount:0
[ 95.890755] anon flags: 0x100000000000840(slab|head|node=0|zone=1)
[ 95.890755] page_type: 0xffffffff()
[ 95.890755] raw: 0100000000000840ffff888006842dc000000000000000000000000000000001
[ 95.890755] raw: ffff88800c38a800000000000010000a00000001ffffffff0000000000000000
[ 95.890755] head: 0100000000000840ffff888006842dc000000000000000000000000000000001
[ 95.890755] head: ffff88800c38a800000000000010000a00000001ffffffff0000000000000000
[ 95.890755] head: 0100000000000003ffffea000030e201ffffea000030e24800000000ffffffff
[ 95.890755] head: 0000000800000000000000000000000000000000ffffffff0000000000000000
[ 95.890755] page dumped because: kasan: bad access detected
[ 95.890755]
[ 95.890755] Memory state around the buggy address:
[ 95.890755] ffff88800c387f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 95.890755] ffff88800c388000: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 95.890755] >ffff88800c388080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 95.890755] ^
[ 95.890755] ffff88800c388100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 95.890755] ffff88800c388180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 95.890755] ==================================================================
Fix this problem by adding a check protected by sco_conn_lock to judget
whether the conn->hcon is null. Because the conn->hcon will be set to null,
when the sock is releasing.
Fixes: ba316be1b6a0 ("Bluetooth: schedule SCO timeouts with delayed_work") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Anderson Nascimento reported a use-after-free splat in tcp_twsk_unique()
with nice analysis.
Since commit ec94c2696f0b ("tcp/dccp: avoid one atomic operation for
timewait hashdance"), inet_twsk_hashdance() sets TIME-WAIT socket's
sk_refcnt after putting it into ehash and releasing the bucket lock.
Thus, there is a small race window where other threads could try to
reuse the port during connect() and call sock_hold() in tcp_twsk_unique()
for the TIME-WAIT socket with zero refcnt.
If that happens, the refcnt taken by tcp_twsk_unique() is overwritten
and sock_put() will cause underflow, triggering a real use-after-free
somewhere else.
To avoid the use-after-free, we need to use refcount_inc_not_zero() in
tcp_twsk_unique() and give up on reusing the port if it returns false.
To fix this issue, change tcp_shutdown() to not
perform a TCP_SYN_RECV -> TCP_FIN_WAIT1 transition,
which makes no sense anyway.
When tcp_rcv_state_process() later changes socket state
from TCP_SYN_RECV to TCP_ESTABLISH, then look at
sk->sk_shutdown to finally enter TCP_FIN_WAIT1 state,
and send a FIN packet from a sane socket state.
This means tcp_send_fin() can now be called from BH
context, and must use GFP_ATOMIC allocations.
The software GRO path for esp transport mode uses skb_mac_header_rebuild
prior to re-injecting the packet via the xfrm_napi_dev. This only
copies skb->mac_len bytes of header which may not be sufficient if the
packet contains 802.1Q tags or other VLAN tags. Worse copying only the
initial header will leave a packet marked as being VLAN tagged but
without the corresponding tag leading to mangling when it is later
untagged.
The VLAN tags are important when receiving the decrypted esp transport
mode packet after GRO processing to ensure it is received on the correct
interface.
Therefore record the full mac header length in xfrm*_transport_input for
later use in corresponding xfrm*_transport_finish to copy the entire mac
header when rebuilding the mac header for GRO. The skb->data pointer is
left pointing skb->mac_header bytes after the start of the mac header as
is expected by the network stack and network and transport header
offsets reset to this location.
Fixes: 7785bba299a8 ("esp: Add a software GRO codepath") Signed-off-by: Paul Davey <paul.davey@alliedtelesis.co.nz> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We don't need to hold the prepare_lock when dropping a ref on a struct
clk_core. The release function is only freeing memory and any code with
a pointer reference has already unlinked anything pointing to the
clk_core. This reduces the holding area of the prepare_lock a bit.
Note that we also don't call free_clk() with the prepare_lock held.
There isn't any reason to do that.
9p is a remote network protocol, and it doesn't support asynchronous
notifications from the server. Ensure that we don't hand out any leases
since we can't guarantee they'll be broken when a file's contents
change.
Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Garbage in plain 9P2000's perm bits is allowed through, which causes it
to be able to set (among others) the suid bit. This was presumably not
the intent since the unix extended bits are handled explicitly and
conditionally on .u.
Signed-off-by: Joakim Sindholt <opensource@zhasha.com> Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
valid-adjtimex.c:66:6: warning: shifting a negative signed value is undefined [-Wshift-negative-value]
-499<<16,
~~~~^
valid-adjtimex.c:67:6: warning: shifting a negative signed value is undefined [-Wshift-negative-value]
-450<<16,
~~~~^
..
Fix it by using a multiply by (1 << 16) instead of shifting negative values
in the valid-adjtimex test case. Align the values for better readability.
thread_info.syscall is used by syscall_get_nr to supply syscall nr
over a thread stack frame.
Previously, thread_info.syscall is only saved at syscall_trace_enter
when syscall tracing is enabled. However rest of the kernel code do
expect syscall_get_nr to be available without syscall tracing. The
previous design breaks collect_syscall.
Move saving process to syscall entry to fix it.
Reported-by: Xi Ruoyao <xry111@xry111.site> Link: https://github.com/util-linux/util-linux/issues/2867 Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the systemd-modules service loads the target module, the credentials of
that userspace process will be used to validate the access to the target db
directory. SELinux will prevent it, reporting an error like the following:
It is possible to clear a root's IN_TRANS tag from the radix tree, but
not clear its PERTRANS, if there is some error in between. Eliminate
that possibility by moving the free up to where we clear the tag.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Boris Burkov <boris@bur.io> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, this call site in btrfs_clear_delalloc_extent() only converts
the reservation. We are marking it not delalloc, so I don't think it
makes sense to keep the rsv around. This is a path where we are not
sure to join a transaction, so it leads to incorrect free-ing during
umount.
Helps with the pass rate of generic/269 and generic/475.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Boris Burkov <boris@bur.io> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the FireWire OHCI interrupt handler, if a bus reset interrupt has
occurred, mask bus reset interrupts until bus_reset_work has serviced and
cleared the interrupt.
Normally, we always leave bus reset interrupts masked. We infer the bus
reset from the self-ID interrupt that happens shortly thereafter. A
scenario where we unmask bus reset interrupts was introduced in 2008 in a007bb857e0b26f5d8b73c2ff90782d9c0972620: If
OHCI_PARAM_DEBUG_BUSRESETS (8) is set in the debug parameter bitmask, we
will unmask bus reset interrupts so we can log them.
irq_handler logs the bus reset interrupt. However, we can't clear the bus
reset event flag in irq_handler, because we won't service the event until
later. irq_handler exits with the event flag still set. If the
corresponding interrupt is still unmasked, the first bus reset will
usually freeze the system due to irq_handler being called again each
time it exits. This freeze can be reproduced by loading firewire_ohci
with "modprobe firewire_ohci debug=-1" (to enable all debugging output).
Apparently there are also some cases where bus_reset_work will get called
soon enough to clear the event, and operation will continue normally.
This freeze was first reported a few months after a007bb85 was committed,
but until now it was never fixed. The debug level could safely be set
to -1 through sysfs after the module was loaded, but this would be
ineffectual in logging bus reset interrupts since they were only
unmasked during initialization.
irq_handler will now leave the event flag set but mask bus reset
interrupts, so irq_handler won't be called again and there will be no
freeze. If OHCI_PARAM_DEBUG_BUSRESETS is enabled, bus_reset_work will
unmask the interrupt after servicing the event, so future interrupts
will be caught as desired.
As a side effect to this change, OHCI_PARAM_DEBUG_BUSRESETS can now be
enabled through sysfs in addition to during initial module loading.
However, when enabled through sysfs, logging of bus reset interrupts will
be effective only starting with the second bus reset, after
bus_reset_work has executed.
If the RBUF logic is not reset when the kernel starts then there
may be some data left over from any network boot loader. If the
64-byte packet headers are enabled then this can be fatal.
Extend bcmgenet_dma_disable to do perform the reset, but not when
called from bcmgenet_resume in order to preserve a wake packet.
N.B. This different handling of resume is just based on a hunch -
why else wouldn't one reset the RBUF as well as the TBUF? If this
isn't the case then it's easy to change the patch to make the RBUF
reset unconditional.
Signed-off-by: Phil Elwell <phil@raspberrypi.com> Signed-off-by: Maarten Vanraes <maarten@rmail.be> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For shutting up spurious KMSAN uninit-value warnings, just replace
kmalloc() calls with kzalloc() for the buffers used for
communications. There should be no real issue with the original code,
but it's still better to cover.
The session resources are used by FW and driver when session is offloaded,
once session is uploaded these resources are not used. The lock is not
required as these fields won't be used any longer. The offload and upload
calls are sequential, hence lock is not required.
sk->sk_rcvbuf in __sock_queue_rcv_skb() and __sk_receive_skb() can be
changed by other threads. Mark this as benign using READ_ONCE().
This patch is aimed at reducing the number of benign races reported by
KCSAN in order to focus future debugging effort on harmful races.
Signed-off-by: linke li <lilinke99@qq.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Running kernel-doc on ieee80211_i.h flagged the following:
net/mac80211/ieee80211_i.h:145: warning: expecting prototype for enum ieee80211_corrupt_data_flags. Prototype was for enum ieee80211_bss_corrupt_data_flags instead
net/mac80211/ieee80211_i.h:162: warning: expecting prototype for enum ieee80211_valid_data_flags. Prototype was for enum ieee80211_bss_valid_data_flags instead
In punch_hole(), when the offset lies in the final block for a given
height, there is no hole to punch, but the maximum size check fails to
detect that. Consequently, punch_hole() will try to punch a hole beyond
the end of the metadata and fail. Fix the maximum size check.
Signed-off-by: Andrew Price <anprice@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Typically when an out of resource CQE status is detected, the
lpfc_ramp_down_queue_handler() logic is called to help reduce I/O load by
reducing an sdev's queue_depth.
However, the current lpfc_rampdown_queue_depth() logic does not help reduce
queue_depth. num_cmd_success is never updated and is always zero, which
means new_queue_depth will always be set to sdev->queue_depth. So,
new_queue_depth = sdev->queue_depth - new_queue_depth always sets
new_queue_depth to zero. And, scsi_change_queue_depth(sdev, 0) is
essentially a no-op.
Change the lpfc_ramp_down_queue_handler() logic to set new_queue_depth
equal to sdev->queue_depth subtracted from number of times num_rsrc_err was
incremented. If num_rsrc_err is >= sdev->queue_depth, then set
new_queue_depth equal to 1. Eventually, the frequency of Good_Status
frames will signal SCSI upper layer to auto increase the queue_depth back
to the driver default of 64 via scsi_handle_queue_ramp_up().
While PLL CPUX clock rate change when CPU is running from it works in
vast majority of cases, now and then it causes instability. This leads
to system crashes and other undefined behaviour. After a lot of testing
(30+ hours) while also doing a lot of frequency switches, we can't
observe any instability issues anymore when doing reparenting to stable
clock like 24 MHz oscillator.
Calling skb_copy on a SKB_GSO_FRAGLIST skb is not valid, since it returns
an invalid linearized skb. This code only needs to change the ethernet
header, so pskb_copy is the right function to call here.
Fixes: 6db6f0eae605 ("bridge: multicast to unicast") Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For each supported switch, add an entry to the info structure for the
number of MACs which can be stored in the ATU. This will later be used
to export the ATU as a devlink resource, and indicate its occupancy,
how full the ATU is.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: b9a61c20179f ("net: dsa: mv88e6xxx: Fix number of databases for 88E6141 / 88E6341") Signed-off-by: Sasha Levin <sashal@kernel.org>
In qede_flow_spec_to_rule(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced qede_flow_spec_to_rule(),
and this call to qede_parse_flow_attr(), it looks
like it just duplicated how it was already used.
Only compile tested.
Fixes: 37c5d3efd7f8 ("qede: use ethtool_rx_flow_rule() to remove duplicated parser code") Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
NSH can encapsulate IPv4, IPv6, Ethernet, NSH, and MPLS. As the inner
protocol can be Ethernet, NSH GSO handler, nsh_gso_segment(), calls
skb_mac_gso_segment() to invoke inner protocol GSO handlers.
nsh_gso_segment() does the following for the original skb before
calling skb_mac_gso_segment()
1. reset skb->network_header
2. save the original skb->{mac_heaeder,mac_len} in a local variable
3. pull the NSH header
4. resets skb->mac_header
5. set up skb->mac_len and skb->protocol for the inner protocol.
and does the following for the segmented skb
6. set ntohs(ETH_P_NSH) to skb->protocol
7. push the NSH header
8. restore skb->mac_header
9. set skb->mac_header + mac_len to skb->network_header
10. restore skb->mac_len
There are two problems in 6-7 and 8-9.
(a)
After 6 & 7, skb->data points to the NSH header, so the outer header
(ETH_P_8021AD in this case) is stripped when skb is sent out of netdev.
Also, if NSH is encapsulated by NSH + Ethernet (so NSH-Ethernet-NSH),
skb_pull() in the first nsh_gso_segment() will make skb->data point
to the middle of the outer NSH or Ethernet header because the Ethernet
header is not pulled by the second nsh_gso_segment().
(b)
While restoring skb->{mac_header,network_header} in 8 & 9,
nsh_gso_segment() does not assume that the data in the linear
buffer is shifted.
However, udp6_ufo_fragment() could shift the data and change
skb->mac_header accordingly as demonstrated by syzbot.
If this happens, even the restored skb->mac_header points to
the middle of the outer header.
It seems nsh_gso_segment() has never worked with outer headers so far.
At the end of nsh_gso_segment(), the outer header must be restored for
the segmented skb, instead of the NSH header.
To do that, let's calculate the outer header position relatively from
the inner header and set skb->{data,mac_header,protocol} properly.
Currently, we allocate a nbytes-sized kernel buffer and copy nbytes from
userspace to that buffer. Later, we use sscanf on this buffer but we don't
ensure that the string is terminated inside the buffer, this can lead to
OOB read when using sscanf. Fix this issue by using memdup_user_nul
instead of memdup_user.
The function __storage_key_init_range() expects the end address to be
the first byte outside the range to be initialized. I.e. end - start
should be the size of the area to be initialized.
The current code works because __storage_key_init_range() will still loop
over every page in the range, but it is slower than using sske_frame().
projects / thirdparty / kernel / stable.git / log
