Upstream currently never calls wcn36xx_smd_end_scan, and in some cases[1]
still sends finish_scan_req twice in a row or before init_scan_req. A
typical connected scan looks like this:
Note that upstream will not do batching of 3 active-probe scans before
returning to the operating channel, and this patch does not change that.
To match downstream in this aspect, adjust IEEE80211_PROBE_DELAY and/or
the 125ms max off-channel time in ieee80211_scan_state_decision.
[1]: commit d195d7aac09b ("wcn36xx: Ensure finish scan is not requested
before start scan") addressed one case of finish_scan_req being sent
without a preceding init_scan_req (the case of the operating channel
coinciding with the first scan channel); two other cases are:
1) if SW scan is started and aborted immediately, without scanning any
channels, we send a finish_scan_req without ever sending init_scan_req,
and
2) as SW scan logic always returns us to the operating channel before
calling wcn36xx_sw_scan_complete, finish_scan_req is always sent twice
at the end of a SW scan
Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by: Benjamin Li <benl@squareup.com> Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211027170306.555535-4-benl@squareup.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 875a4d536842 ("drm/vc4: drv: Disable the CRTC at boot
time"), during the initial setup of the driver we call into the VC4 HDMI
controller hooks to make sure the controller is properly disabled.
However, we were never making sure that the device was properly powered
while doing so. This never resulted in any (reported) issue in practice,
but since the introduction of commit 4209f03fcb8e ("drm/vc4: hdmi: Warn
if we access the controller while disabled") we get a loud complaint
when we do that kind of access.
Let's make sure we have the HDMI controller properly powered while
disabling it.
Fixes: 875a4d536842 ("drm/vc4: drv: Disable the CRTC at boot time") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org> Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210923185013.826679-1-maxime@cerno.tech Signed-off-by: Sasha Levin <sashal@kernel.org>
Since our pre_crtc_configure hook returned void, we didn't implement a
goto-based error path handling, leading to errors like failing to put
back the device in pm_runtime in all the error paths, but also failing
to disable the pixel clock if clk_set_min_rate on the HSM clock fails.
Move to a goto-based implementation to have an easier consitency.
In the bind hook, we actually need the device to have the HSM clock
running during the final part of the display initialisation where we
reset the controller and initialise the CEC component.
Failing to do so will result in a complete, silent, hang of the CPU.
If the HPD GPIO is not available and drm_probe_ddc fails, we end up
reading the HDMI_HOTPLUG register, but the controller might be powered
off resulting in a CPU hang. Make sure we have the power domain and the
HSM clock powered during the detect cycle to prevent the hang from
happening.
Fixes: 4f6e3d66ac52 ("drm/vc4: Add runtime PM support to the HDMI encoder driver") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org> Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> Tested-by: Michael Stapelberg <michael@stapelberg.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-6-maxime@cerno.tech Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to access the HDMI controller, we need to make sure the HSM
clock is enabled. If we were to access it with the clock disabled, the
CPU would completely hang, resulting in an hard crash.
Since we have different code path that would require it, let's move that
clock enable / disable to runtime_pm that will take care of the
reference counting for us.
Since we also want to change the HSM clock rate and it's only valid
while the clock is disabled, we need to move the clk_set_min_rate() call
on the HSM clock above pm_runtime_get_and_sync().
When the firmware doesn't setup the HSM rate (such as when booting
without an HDMI cable plugged in), its rate is 0 and thus any register
access results in a CPU stall, even though HSM is enabled.
Let's enforce a minimum rate at boot to avoid this issue.
Fixes: 4f6e3d66ac52 ("drm/vc4: Add runtime PM support to the HDMI encoder driver") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org> Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> Tested-by: Michael Stapelberg <michael@stapelberg.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-4-maxime@cerno.tech Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver, once it found a divider, tries to round it up by increasing
the least significant bit of the fractional part by one when the
round_up argument is set and there's a remainder.
However, since it increases the divider it will actually reduce the
clock rate below what we were asking for, leading to issues with
clk_set_min_rate() that will complain that our rounded clock rate is
below the minimum of the rate.
Since the dividers are fairly precise already, let's remove that part so
that we can have clk_set_min_rate() working.
This is effectively a revert of 9c95b32ca093 ("clk: bcm2835: add a round
up ability to the clock divisor").
Fixes: 9c95b32ca093 ("clk: bcm2835: add a round up ability to the clock divisor") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org> Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> # boot and basic functionality Tested-by: Michael Stapelberg <michael@stapelberg.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-3-maxime@cerno.tech Signed-off-by: Sasha Levin <sashal@kernel.org>
If cmtp_init_sockets() in cmtp_init() fails, cmtp_init() still returns
success. This will cause a kernel bug when accessing uncreated ctmp
related data when the module exits.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On the reception of packets with an invalid packet type, the memory of
the allocated socket buffers is never freed. Add a default case that frees
these to avoid a memory leak.
Fixes: afd2daa26c7a ("Bluetooth: Add support for virtio transport driver") Signed-off-by: Soenke Huster <soenke.huster@eknoes.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 43c2de1002d2 ("drm/rockchip: dsi: move all lane config except
LCDC mux to bind()"), we perform most HW configuration in the bind()
function. This configuration may be lost on suspend/resume, so we
need to call it again. That may lead to errors like this after system
suspend/resume:
Tested on Acer Chromebook Tab 10 (RK3399 Gru-Scarlet).
Note that early mailing list versions of this driver borrowed Rockchip's
downstream/BSP solution, to do HW configuration in mode_set() (which
*is* called at the appropriate pre-enable() times), but that was
discarded along the way. I've avoided that still, because mode_set()
documentation doesn't suggest this kind of purpose as far as I can tell.
Fixes: 43c2de1002d2 ("drm/rockchip: dsi: move all lane config except LCDC mux to bind()") Cc: <stable@vger.kernel.org> Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20210928143413.v3.2.I4e9d93aadb00b1ffc7d506e3186a25492bf0b732@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 43c2de1002d2 ("drm/rockchip: dsi: move all lane config except
LCDC mux to bind()"), we moved most HW configuration to bind(), but we
didn't move the runtime PM management. Therefore, depending on initial
boot state, runtime-PM workqueue delays, and other timing factors, we
may disable our power domain in between the hardware configuration
(bind()) and when we enable the display. This can cause us to lose
hardware state and fail to configure our display. For example:
dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO
panel-innolux-p079zca ff960000.mipi.0: failed to write command 0
We should match the runtime PM to the lifetime of the bind()/unbind()
cycle.
Tested on Acer Chrometab 10 (RK3399 Gru-Scarlet), with panel drivers
built either as modules or built-in.
Side notes: it seems one is more likely to see this problem when the
panel driver is built into the kernel. I've also seen this problem
bisect down to commits that simply changed Kconfig dependencies, because
it changed the order in which driver init functions were compiled into
the kernel, and therefore the ordering and timing of built-in device
probe.
If we fail to attach (e.g., because 1 of 2 dual-DSI controllers aren't
ready), we leave a dangling drm_panel reference to freed memory. Clean
that up on failure.
This problem exists since the driver's introduction, but is especially
relevant after refactored for dual-DSI variants.
If we fail to attach (e.g., because 1 of 2 dual-DSI controllers aren't
ready), we leave a dangling drm_panel reference to freed memory. Clean
that up on failure.
If drm_fs_inode_new() fails in drm_dev_init(), dev->anon_inode will point
to PTR_ERR(...) instead of NULL. This will result in null-ptr-deref when
drm_fs_inode_free(dev->anon_inode) is called.
The "label" pointer is used for debug output. The code assumes that it
is either NULL or valid, but it is never set to NULL. It is either
valid or uninitialized.
Fixes: 0c275c30176b ("drm/bridge: Add bridge driver for display connectors") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20211013080825.GE6010@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to group sockets being connected using L2CAP_MODE_EXT_FLOWCTL
the pid is used but sk_peer_pid was not being initialized as it is
currently only done for af_unix.
Image there are 3 items in the local list (@list). In the first
traversal, A is not deleted from @list.
1) A->B->C
^
|
pos (leave)
In the second traversal, B is deleted from @list. Concurrently, A is
deleted from @list through shmem_evict_inode() since last reference
counter of inode is dropped by other thread. Then the @list is corrupted.
2) A->B->C
^ ^
| |
evict pos (drop)
We should make sure the inode is either on the global list or deleted from
any local list before iput().
Fixed by moving inodes back to global list before we put them.
[akpm@linux-foundation.org: coding style fixes]
Link: https://lkml.kernel.org/r/20211125064502.99983-1-ligang.bdlg@bytedance.com Fixes: 779750d20b93 ("shmem: split huge pages beyond i_size under memory pressure") Signed-off-by: Gang Li <ligang.bdlg@bytedance.com> Reviewed-by: Muchun Song <songmuchun@bytedance.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently ath11k only support string type with bus, chip id and board id
such as "bus=ahb,qmi-chip-id=1,qmi-board-id=4" for ahb bus chip and
"bus=pci,qmi-chip-id=0,qmi-board-id=255" for PCIe bus chip in
board-2.bin. For WCN6855, it is not enough to distinguish all different
chips.
This is to add a new string type which include bus, chip id, board id,
vendor, device, subsystem-vendor and subsystem-device for WCN6855.
ath11k will first load board-2.bin and search in it for the board data
with the above parameters, if matched one board data, then download it
to firmware, if not matched any one, then ath11k will download the file
board.bin to firmware.
The above failure happened when calling kmalloc() to allocate buffer with
GFP_DMA. It requests to allocate slab page from DMA zone while no managed
pages at all in there.
Because in the current kernel, dma-kmalloc will be created as long as
CONFIG_ZONE_DMA is enabled. However, kdump kernel of x86_64 doesn't have
managed pages on DMA zone since commit 6f599d84231f ("x86/kdump: Always
reserve the low 1M when the crashkernel option is specified"). The
failure can be always reproduced.
For now, let's mute the warning of allocation failure if requesting pages
from DMA zone while no managed pages.
[akpm@linux-foundation.org: fix warning]
Link: https://lkml.kernel.org/r/20211223094435.248523-4-bhe@redhat.com Fixes: 6f599d84231f ("x86/kdump: Always reserve the low 1M when the crashkernel option is specified") Signed-off-by: Baoquan He <bhe@redhat.com> Acked-by: John Donnelly <john.p.donnelly@oracle.com> Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Borislav Petkov <bp@alien8.de> Cc: Christoph Hellwig <hch@lst.de> Cc: David Hildenbrand <david@redhat.com> Cc: David Laight <David.Laight@ACULAB.COM> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Robin Murphy <robin.murphy@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently three dma atomic pools are initialized as long as the relevant
kernel codes are built in. While in kdump kernel of x86_64, this is not
right when trying to create atomic_pool_dma, because there's no managed
pages in DMA zone. In the case, DMA zone only has low 1M memory
presented and locked down by memblock allocator. So no pages are added
into buddy of DMA zone. Please check commit f1d4d47c5851 ("x86/setup:
Always reserve the first 1M of RAM").
Then in kdump kernel of x86_64, it always prints below failure message:
DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
swapper/0: page allocation failure: order:5, mode:0xcc1(GFP_KERNEL|GFP_DMA), nodemask=(null),cpuset=/,mems_allowed=0
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-0.rc5.20210611git929d931f2b40.42.fc35.x86_64 #1
Hardware name: Dell Inc. PowerEdge R910/0P658H, BIOS 2.12.0 06/04/2018
Call Trace:
dump_stack+0x7f/0xa1
warn_alloc.cold+0x72/0xd6
__alloc_pages_slowpath.constprop.0+0xf29/0xf50
__alloc_pages+0x24d/0x2c0
alloc_page_interleave+0x13/0xb0
atomic_pool_expand+0x118/0x210
__dma_atomic_pool_init+0x45/0x93
dma_atomic_pool_init+0xdb/0x176
do_one_initcall+0x67/0x320
kernel_init_freeable+0x290/0x2dc
kernel_init+0xa/0x111
ret_from_fork+0x22/0x30
Mem-Info:
......
DMA: failed to allocate 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocation
DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
Here, let's check if DMA zone has managed pages, then create
atomic_pool_dma if yes. Otherwise just skip it.
Link: https://lkml.kernel.org/r/20211223094435.248523-3-bhe@redhat.com Fixes: 6f599d84231f ("x86/kdump: Always reserve the low 1M when the crashkernel option is specified") Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: John Donnelly <john.p.donnelly@oracle.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Christoph Lameter <cl@linux.com> Cc: David Laight <David.Laight@ACULAB.COM> Cc: David Rientjes <rientjes@google.com> Cc: Hyeonggon Yoo <42.hyeyoo@gmail.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
***Root cause:
In the current kernel, it assumes that DMA zone must have managed pages
and try to request pages if CONFIG_ZONE_DMA is enabled. While this is not
always true. E.g in kdump kernel of x86_64, only low 1M is presented and
locked down at very early stage of boot, so that this low 1M won't be
added into buddy allocator to become managed pages of DMA zone. This
exception will always cause page allocation failure if page is requested
from DMA zone.
***Investigation:
This failure happens since below commit merged into linus's tree. 1a6a9044b967 x86/setup: Remove CONFIG_X86_RESERVE_LOW and reservelow= options 23721c8e92f7 x86/crash: Remove crash_reserve_low_1M() f1d4d47c5851 x86/setup: Always reserve the first 1M of RAM 7c321eb2b843 x86/kdump: Remove the backup region handling 6f599d84231f x86/kdump: Always reserve the low 1M when the crashkernel option is specified
Before them, on x86_64, the low 640K area will be reused by kdump kernel.
So in kdump kernel, the content of low 640K area is copied into a backup
region for dumping before jumping into kdump. Then except of those firmware
reserved region in [0, 640K], the left area will be added into buddy
allocator to become available managed pages of DMA zone.
However, after above commits applied, in kdump kernel of x86_64, the low
1M is reserved by memblock, but not released to buddy allocator. So any
later page allocation requested from DMA zone will fail.
At the beginning, if crashkernel is reserved, the low 1M need be locked
down because AMD SME encrypts memory making the old backup region
mechanims impossible when switching into kdump kernel.
Later, it was also observed that there are BIOSes corrupting memory
under 1M. To solve this, in commit f1d4d47c5851, the entire region of
low 1M is always reserved after the real mode trampoline is allocated.
Besides, recently, Intel engineer mentioned their TDX (Trusted domain
extensions) which is under development in kernel also needs to lock down
the low 1M. So we can't simply revert above commits to fix the page allocation
failure from DMA zone as someone suggested.
***Solution:
Currently, only DMA atomic pool and dma-kmalloc will initialize and
request page allocation with GFP_DMA during bootup.
So only initializ DMA atomic pool when DMA zone has available managed
pages, otherwise just skip the initialization.
For dma-kmalloc(), for the time being, let's mute the warning of
allocation failure if requesting pages from DMA zone while no manged
pages. Meanwhile, change code to use dma_alloc_xx/dma_map_xx API to
replace kmalloc(GFP_DMA), or do not use GFP_DMA when calling kmalloc() if
not necessary. Christoph is posting patches to fix those under
drivers/scsi/. Finally, we can remove the need of dma-kmalloc() as people
suggested.
This patch (of 3):
In some places of the current kernel, it assumes that dma zone must have
managed pages if CONFIG_ZONE_DMA is enabled. While this is not always
true. E.g in kdump kernel of x86_64, only low 1M is presented and locked
down at very early stage of boot, so that there's no managed pages at all
in DMA zone. This exception will always cause page allocation failure if
page is requested from DMA zone.
Here add function has_managed_dma() and the relevant helper functions to
check if there's DMA zone with managed pages. It will be used in later
patches.
Link: https://lkml.kernel.org/r/20211223094435.248523-1-bhe@redhat.com Link: https://lkml.kernel.org/r/20211223094435.248523-2-bhe@redhat.com Fixes: 6f599d84231f ("x86/kdump: Always reserve the low 1M when the crashkernel option is specified") Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: John Donnelly <john.p.donnelly@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Christoph Lameter <cl@linux.com> Cc: Hyeonggon Yoo <42.hyeyoo@gmail.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: David Laight <David.Laight@ACULAB.COM> Cc: Borislav Petkov <bp@alien8.de> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Robin Murphy <robin.murphy@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like other SATA controller chips in the Marvell 88SE91xx series, the
Marvell 88SE9125 has the same DMA requester ID hardware bug that prevents
it from working under IOMMU. Add it to the list of devices that need the
quirk.
Without this patch, device initialization fails with DMA errors:
ata8: softreset failed (1st FIS failed)
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
After applying the patch, the controller can be successfully initialized:
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 330)
ata8.00: ATAPI: PIONEER BD-RW BDR-207M, 1.21, max UDMA/100
ata8.00: configured for UDMA/100
scsi 7:0:0:0: CD-ROM PIONEER BD-RW BDR-207M 1.21 PQ: 0 ANSI: 5
Link: https://lore.kernel.org/r/YahpKVR+McJVDdkD@work Reported-by: Sam Bingner <sam@bingner.com> Tested-by: Sam Bingner <sam@bingner.com> Tested-by: Yifeng Li <tomli@tomli.me> Signed-off-by: Yifeng Li <tomli@tomli.me> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Krzysztof Wilczyński <kw@linux.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA buffers of 2D/3D engines aren't mapped properly when
CONFIG_ARM_DMA_USE_IOMMU=y. The memory management code of Tegra DRM driver
has a longstanding overhaul overdue and it's not obvious where the problem
is in this case. Hence let's add back the old workaround which we already
had sometime before. It explicitly detaches DRM devices from the offending
implicit IOMMU domain. This fixes a completely broken 2d/3d drivers in
case of ARM32 multiplatform kernel config.
Host1x DMA buffer isn't mapped properly when CONFIG_ARM_DMA_USE_IOMMU=y.
The memory management code of Host1x driver has a longstanding overhaul
overdue and it's not obvious where the problem is in this case. Hence
let's add back the old workaround which we already had sometime before.
It explicitly detaches Host1x device from the offending implicit IOMMU
domain. This fixes a completely broken Host1x DMA in case of ARM32
multiplatform kernel config.
In __arm_v7s_alloc_table function:
iommu call kmem_cache_alloc to allocate page table, this function
allocate memory may fail, when kmem_cache_alloc fails to allocate
table, call virt_to_phys will be abnomal and return unexpected phys
and goto out_free, then call kmem_cache_free to release table will
trigger KE, __get_free_pages and free_pages have similar problem,
so add error handle for page table allocation failure.
Fixes: 29859aeb8a6e ("iommu/io-pgtable-arm-v7s: Abort allocation when table address overflows the PTE") Signed-off-by: Yunfei Wang <yf.wang@mediatek.com> Cc: <stable@vger.kernel.org> # 5.10.* Acked-by: Robin Murphy <robin.murphy@arm.com> Link: https://lore.kernel.org/r/20211207113315.29109-1-yf.wang@mediatek.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The erratum 1418040 workaround enables CNTVCT_EL1 access trapping in EL0
when executing compat threads. The workaround is applied when switching
between tasks, but the need for the workaround could also change at an
exec(), when a non-compat task execs a compat binary or vice versa. Apply
the workaround in arch_setup_new_exec().
This leaves a small window of time between SET_PERSONALITY and
arch_setup_new_exec where preemption could occur and confuse the old
workaround logic that compares TIF_32BIT between prev and next. Instead, we
can just read cntkctl to make sure it's in the state that the next task
needs. I measured cntkctl read time to be about the same as a mov from a
general-purpose register on N1. Update the workaround logic to examine the
current value of cntkctl instead of the previous task's compat state.
Fixes: d49f7d7376d0 ("arm64: Move handling of erratum 1418040 into C code") Cc: <stable@vger.kernel.org> # 5.9.x Signed-off-by: D Scott Phillips <scott@os.amperecomputing.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20211220234114.3926-1-scott@os.amperecomputing.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a potential race between queue_work() returning and the
queued-work running that could result in put_device() running before
get_device(). Introduce the cxl_nvdimm_bridge_state_work() helper that
takes the reference unconditionally, but drops it if no new work was
queued, to keep the references balanced.
Fixes: 8fdcb1704f61 ("cxl/pmem: Add initial infrastructure for pmem support") Cc: <stable@vger.kernel.org> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Ben Widawsky <ben.widawsky@intel.com> Link: https://lore.kernel.org/r/163553734757.2509761.3305231863616785470.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During SYS_ERR condition, as a response to the MHI_RESET from host, some
devices tend to issue BHI interrupt without clearing the SYS_ERR state in
the device. This creates a race condition and causes a failure in booting
up the device.
The issue is seen on the Sierra Wireless EM9191 modem during SYS_ERR
handling in mhi_async_power_up(). Once the host detects that the device
is in SYS_ERR state, it issues MHI_RESET and waits for the device to
process the reset request. During this time, the device triggers the BHI
interrupt to the host without clearing SYS_ERR condition. So the host
starts handling the SYS_ERR condition again.
To fix this issue, let's register the IRQ handler only after handling the
SYS_ERR check to avoid getting spurious IRQs from the device.
Fixes: e18d4e9fa79b ("bus: mhi: core: Handle syserr during power_up") Cc: stable@vger.kernel.org Reported-by: Aleksander Morgado <aleksander@aleksander.es> Tested-by: Aleksander Morgado <aleksander@aleksander.es> Tested-by: Thomas Perrot <thomas.perrot@bootlin.com> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20211216081227.237749-8-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'wake-capable' entry in channel configuration is not set when
parsing the configuration specified by the controller driver. Add
the missing entry to ensure channel is correctly specified as a
'wake-capable' channel.
There is no reason for shutting down MHI ungracefully on freeze,
this causes the MHI host stack & device stack to not be aligned
anymore since the proper MHI reset sequence is not performed for
ungraceful shutdown.
IIO triggers are software IRQ chips that split an incoming IRQ into
separate IRQs routed to all devices using the trigger.
When all consumers are done then a trigger callback reenable() is
called. There are a few circumstances under which this can happen
in atomic context.
1) A single user of the trigger that calls the iio_trigger_done()
function from interrupt context.
2) A race between disconnecting the last device from a trigger and
the trigger itself sucessfully being disabled.
To avoid a resulting scheduling whilst atomic, close this second corner
by using schedule_work() to ensure the reenable is not done in atomic
context.
Note that drivers must be careful to manage the interaction of
set_state() and reenable() callbacks to ensure appropriate reference
counting if they are relying on the same hardware controls.
Deliberately taking this the slow path rather than via a fixes tree
because the error has hard to hit and I would like it to soak for a while
before hitting a release kernel.
Unfortuanately a non standards compliant ACPI ID is known to be
in the wild on some AAEON boards.
Partly revert the removal of these IDs so that ADC081C will again
work + add a comment to that affect for future reference.
Whilst here use generic firmware properties rather than the ACPI
specific handling previously found in this driver.
Reported-by: Kunyang Fan <Kunyang_Fan@aaeon.com.tw> Fixes: c458b7ca3fd0 ("iio:adc:ti-adc081c: Drop ACPI ids that seem very unlikely to be official.") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Kunyang Fan <Kunyang_Fan@aaeon.com.tw> #UP-extremei11 Link: https://lore.kernel.org/r/20211205172728.2826512-1-jic23@kernel.org Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't blindly copy status value received from the firmware
into internal client status field,
It may be positive and ERR_PTR(ret) will translate it
into an invalid address and the caller will crash.
Put the error code into the client status on failure.
In case device registration fails during probe, the driver state and
the embedded platform device structure needs to be freed using
platform_device_put() to properly free all resources (e.g. the device
name).
Fixes: 0a0b7a5f7a04 ("can: add driver for Softing card") Link: https://lore.kernel.org/all/20211222104843.6105-1-johan@kernel.org Cc: stable@vger.kernel.org # 2.6.38 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The en/disable_irq() functions keep track of the 'depth': i.e. if
interrupts are disabled twice, then it needs to enable_irq() calls to
enable them again. The cec-pin framework didn't take this into accound
and could disable irqs multiple times, and it expected that a single
enable_irq() would enable them again.
Move all calls to en/disable_irq() to the kthread where it is easy
to keep track of the current irq state and ensure that multiple
en/disable_irq calls never happen.
If interrupts where disabled twice, then they would never turn on
again, leaving the CEC adapter in a dead state.
This fixes a problem where closing the tuner would leave it in a state
where it would not tune to any channel when reopened. This problem was
discovered as part of https://github.com/hselasky/webcamd/issues/16.
Since adap->id is 0 or 1, this bit-shift overflows, which is undefined
behavior. The driver still worked in practice as the overflow would in
most environments result in 0, which rendered the line a no-op. When
running the driver as part of webcamd however, the overflow could lead
to 0xff due to optimizations by the compiler, which would, in the end,
improperly shut down the tuner.
The bug is a regression introduced in the commit referenced below. The
present patch causes identical behavior to before that commit for
adap->id equal to 0 or 1. The driver does not contain support for
dib0700 devices with more adapters, assuming such even exist.
Tests have been performed with the Xbox One Digital TV Tuner on amd64.
Not all dib0700 devices are expected to be affected by the regression;
this code path is only taken by those with incorrect endpoint numbers.
If V4L2_CAP_READWRITE is not set, then readbuffers must be set to 0,
otherwise v4l2-compliance will complain.
A note on the Fixes tag below: this patch does not really fix that commit,
but it can be applied from that commit onwards. For older code there is no
guarantee that device_caps is set, so even though this patch would apply,
it will not work reliably.
If powering on the sensor failed, the entire power-off sequence was run
independently of how far the power-on sequence proceeded before the error.
This lead to disabling regulators and/or clock that was not enabled.
Fix this by disabling only clocks and regulators that were enabled
previously.
Fixes: 11c0d8fdccc5 ("media: i2c: Add support for the OV8865 image sensor") Cc: stable@vger.kernel.org Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cec_devnode struct has a lock meant to serialize access
to the fields of this struct. This lock is taken during
device node (un)registration and when opening or releasing a
filehandle to the device node. When the last open filehandle
is closed the cec adapter might be disabled by calling the
adap_enable driver callback with the devnode.lock held.
However, if during that callback a message or event arrives
then the driver will call one of the cec_queue_event()
variants in cec-adap.c, and those will take the same devnode.lock
to walk the open filehandle list.
This obviously causes a deadlock.
This is quite easy to reproduce with the cec-gpio driver since that
uses the cec-pin framework which generated lots of events and uses
a kernel thread for the processing, so when adap_enable is called
the thread is still running and can generate events.
But I suspect that it might also happen with other drivers if an
interrupt arrives signaling e.g. a received message before adap_enable
had a chance to disable the interrupts.
This patch adds a new mutex to serialize access to the fhs list.
When adap_enable() is called the devnode.lock mutex is held, but
not devnode.lock_fhs. The event functions in cec-adap.c will now
use devnode.lock_fhs instead of devnode.lock, ensuring that it is
safe to call those functions from the adap_enable callback.
This specific issue only happens if the last open filehandle is closed
and the physical address is invalid. This is not something that
happens during normal operation, but it does happen when monitoring
CEC traffic (e.g. cec-ctl --monitor) with an unconfigured CEC adapter.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Cc: <stable@vger.kernel.org> # for v5.13 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever new parameter is added to smb configuration, It is possible
to break the execution of the IPC daemon by mismatch size of
request/response. This patch tries to reserve space in ipc request/response
in advance to prevent that.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the client ignores the CreditResponse received from the server and
continues to send the request, ksmbd limits the requests if it exceeds
smb2 max credits.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moves the credit charge deduction from total_credits under the processing
a request. When repeating smb2 lock request and other command request,
there will be a problem that ->total_credits does not decrease.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MS-SMB2 describe session sign like the following.
Session.SigningRequired MUST be set to TRUE under the following conditions:
- If the SMB2_NEGOTIATE_SIGNING_REQUIRED bit is set in the SecurityMode
field of the client request.
- If the SMB2_SESSION_FLAG_IS_GUEST bit is not set in the SessionFlags
field and Session.IsAnonymous is FALSE and either Connection.ShouldSign
or global RequireMessageSigning is TRUE.
When trying guest account connection using nautilus, The login failure
happened on session setup. ksmbd does not allow this connection
when the user is a guest and the connection sign is set. Just do not set
session sign instead of error response as described in the specification.
And this change improves the guest connection in Nautilus.
Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3") Cc: stable@vger.kernel.org # v5.15+ Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "ksmbd_socket" variable is not initialized on this error path.
Cc: stable@vger.kernel.org Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing genphy_loopback() is not applicable for Marvell PHY. Besides
configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control
Register), it is also required to configure same bits in Page 2
Register 21 (MAC Specific Control Register 2) according to speed of
the loopback is operating.
Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps).
FIXME: Based on trial and error test, it seem 1G need to have delay between
soft reset and loopback enablement.
Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration") Cc: <stable@vger.kernel.org> # 5.15.x Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading from the CMOS involves writing to the index register and then
reading from the data register. Therefore access to the CMOS has to be
serialized with rtc_lock. This invocation of CMOS_READ was not
serialized, which could cause trouble when other code is accessing CMOS
at the same time.
Use spin_lock_irq() like the rest of the function.
Nothing in kernel modifies the RTC_DM_BINARY bit, so there could be a
separate pair of spin_lock_irq() / spin_unlock_irq() before doing the
math.
Ammar Faizi reported that our exit code handling is wrong. We truncate
it to the lowest 8 bits but the syscall itself is expected to take a
regular 32-bit signed integer, not an unsigned char. It's the kernel
that later truncates it to the lowest 8 bits. The difference is visible
in strace, where the program below used to show exit(255) instead of
exit(-1):
int main(void)
{
return -1;
}
This patch applies the fix to all archs. x86_64, i386, arm64, armv7 and
mips were all tested and confirmed to work fine now. Risc-v was not
tested but the change is trivial and exactly the same as for other archs.
Reported-by: Ammar Faizi <ammar.faizi@students.amikom.ac.id> Cc: stable@vger.kernel.org Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After re-checking in the spec and comparing stack offsets with glibc,
The last pushed argument must be 16-byte aligned (i.e. aligned before the
call) so that in the callee esp+4 is multiple of 16, so the principle is
the 32-bit equivalent to what Ammar fixed for x86_64. It's possible that
32-bit code using SSE2 or MMX could have been affected. In addition the
frame pointer ought to be zero at the deepest level.
x86 AES-NI routines can deal with unaligned data. Crypto context
(key, iv etc.) have to be aligned but we take care of that separately
by copying it onto the stack. We were feeding unaligned data into
crypto routines up until commit 83c83e658863 ("crypto: aesni -
refactor scatterlist processing") switched to use the full
skcipher API which uses cra_alignmask to decide data alignment.
This fixes 21% performance regression in kTLS.
Tested by booting with CONFIG_CRYPTO_MANAGER_EXTRA_TESTS=y
(and running thru various kTLS packets).
Before this patch, the `_start` function looks like this:
``` 0000000000001170 <_start>:
1170: pop %rdi
1171: mov %rsp,%rsi
1174: lea 0x8(%rsi,%rdi,8),%rdx
1179: and $0xfffffffffffffff0,%rsp
117d: sub $0x8,%rsp
1181: call 1000 <main>
1186: movzbq %al,%rdi
118a: mov $0x3c,%rax
1191: syscall
1193: hlt
1194: data16 cs nopw 0x0(%rax,%rax,1)
119f: nop
```
Note the "and" to %rsp with $-16, it makes the %rsp be 16-byte aligned,
but then there is a "sub" with $0x8 which makes the %rsp no longer
16-byte aligned, then it calls main. That's the bug!
What actually the x86-64 System V ABI mandates is that right before the
"call", the %rsp must be 16-byte aligned, not after the "call". So the
"sub" with $0x8 here breaks the alignment. Remove it.
An example where this rule matters is when the callee needs to align
its stack at 16-byte for aligned move instruction, like `movdqa` and
`movaps`. If the callee can't align its stack properly, it will result
in segmentation fault.
x86-64 System V ABI also mandates the deepest stack frame should be
zero. Just to be safe, let's zero the %rbp on startup as the content
of %rbp may be unspecified when the program starts. Now it looks like
this:
``` 0000000000001170 <_start>:
1170: pop %rdi
1171: mov %rsp,%rsi
1174: lea 0x8(%rsi,%rdi,8),%rdx
1179: xor %ebp,%ebp # zero the %rbp
117b: and $0xfffffffffffffff0,%rsp # align the %rsp
117f: call 1000 <main>
1184: movzbq %al,%rdi
1188: mov $0x3c,%rax
118f: syscall
1191: hlt
1192: data16 cs nopw 0x0(%rax,%rax,1)
119d: nopl (%rax)
```
Cc: Bedirhan KURT <windowz414@gnuweeb.org> Cc: Louvian Lyndal <louvianlyndal@gmail.com> Reported-by: Peter Cordes <peter@cordes.ca> Signed-off-by: Ammar Faizi <ammar.faizi@students.amikom.ac.id>
[wt: I did this on purpose due to a misunderstanding of the spec, other
archs will thus have to be rechecked, particularly i386] Cc: stable@vger.kernel.org Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"Stolen memory" is memory set aside for use by an Intel integrated GPU.
The intel_graphics_quirks() early quirk reserves this memory when it is
called for a GPU that appears in the intel_early_ids[] table of integrated
GPUs.
Previously intel_graphics_quirks() was marked as QFLAG_APPLY_ONCE, so it
was called only for the first Intel GPU found. If a discrete GPU happened
to be enumerated first, intel_graphics_quirks() was called for it but not
for any integrated GPU found later. Therefore, stolen memory for such an
integrated GPU was never reserved.
For example, this problem occurs in this Alderlake-P (integrated) + DG2
(discrete) topology where the DG2 is found first, but stolen memory is
associated with the integrated GPU:
Remove the QFLAG_APPLY_ONCE flag and call intel_graphics_quirks() for every
Intel GPU. Reserve stolen memory for the first GPU that appears in
intel_early_ids[].
[bhelgaas: commit log, add code comment, squash in
https://lore.kernel.org/r/20220118190558.2ququ4vdfjuahicm@ldmartin-desk2] Link: https://lore.kernel.org/r/20220114002843.2083382-1-lucas.demarchi@intel.com Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
raw_smp_processor_id() doesn't return the hart id as stated in
arch/riscv/include/asm/smp.h, use smp_processor_id() instead
to get the cpu id, and cpuid_to_hartid_map() to pass the hart id
to the next kernel. This fixes kexec on HiFive Unleashed/Unmatched
where cpu ids and hart ids don't match (on qemu-virt they match).
On kdump instead of using an intermediate step to relocate the kernel,
that lives in a "control buffer" outside the current kernel's mapping,
we jump to the crash kernel directly by calling riscv_kexec_norelocate().
The current implementation uses va_pa_offset while switching to physical
addressing, however since we moved the kernel outside the linear mapping
this won't work anymore since riscv_kexec_norelocate() is part of the
kernel mapping and we should use kernel_map.va_kernel_pa_offset, and also
take XIP kernel into account.
We don't really need to use va_pa_offset on riscv_kexec_norelocate, we
can just set STVEC to the physical address of the new kernel instead and
let the hart jump to the new kernel on the next instruction after setting
SATP to zero. This fixes kdump and is also simpler/cleaner.
I tested this on the latest qemu and HiFive Unmatched and works as
expected.
Fixes: 2bfc6cd81bd1 ("riscv: Move kernel mapping outside of linear mapping") Signed-off-by: Nick Kossifidis <mick@ics.forth.gr> Reviewed-by: Alexandre Ghiti <alex@ghiti.fr> Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When allocating crash kernel region without explicitly specifying its
base address/size, memblock_phys_alloc_range will attempt to allocate
memory top to bottom (memblock.bottom_up is false), so the crash
kernel region will end up in highmem on 64bit systems. This way
swiotlb can't work on the crash kernel, since there won't be any
32bit addressible memory available for the bounce buffers.
Try to allocate 32bit addressible memory if available, for the
crash kernel by restricting the top search address to be less
than SZ_4G. If that fails fallback to the previous behavior.
I tested this on HiFive Unmatched where the pci-e controller needs
swiotlb to work, with this patch it's possible to access the pci-e
controller on crash kernel and mount the rootfs from the nvme.
Use what is currently the SMP=y version of riscv_cpuid_to_hartid_mask()
for both SMP=y and SMP=n to fix a build failure with KVM=m and SMP=n due
to boot_cpu_hartid not being exported. This also fixes a second bug
where the SMP=n version assumes the sole CPU in the system is in the
incoming mask, which may not hold true in kvm_riscv_vcpu_sbi_ecall() if
the KVM guest VM has multiple vCPUs (on a SMP=n system).
Fixes: 1ef46c231df4 ("RISC-V: Implement new SBI v0.2 extensions") Reported-by: Adam Borowski <kilobyte@angband.pl> Reviewed-by: Anup Patel <anup.patel@wdc.com> Signed-off-by: Sean Christopherson <seanjc@google.com> Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_MAXPHYSMEM_* are actually never used, even the nommu defconfigs
selecting the MAXPHYSMEM_2GB had no effects on PAGE_OFFSET since it was
preempted by !MMU case right before.
In addition, the move of the kernel mapping at the end of the address
space broke the use of MAXPHYSMEM_2G with MMU since it defines PAGE_OFFSET
at the same address as the kernel mapping.
The ECC engine on the JZ4740 SoC requires the ECC data to be read before
the page; using the default page reading function does not work. Indeed,
the old JZ4740 NAND driver (removed in 5.4) did use the 'OOB first' flag
that existed back then.
Use the newly created nand_read_page_hwecc_oob_first() to address this
issue.
This issue was not found when the new ingenic-nand driver was developed,
most likely because the Device Tree used had the nand-ecc-mode set to
"hw_oob_first", which seems to not be supported anymore.
Cc: <stable@vger.kernel.org> # v5.2 Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740") Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-5-paul@crapouillou.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the function nand_read_page_hwecc_oob_first() (previously
nand_davinci_read_page_hwecc_oob_first()) to nand_base.c, and export it
as a GPL symbol, so that it can be used by more modules.
Cc: <stable@vger.kernel.org> # v5.2 Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740") Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-4-paul@crapouillou.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function nand_davinci_read_page_hwecc_oob_first() first reads the
OOB data, extracts the ECC information, programs the ECC hardware before
reading the actual data in a loop.
Right after the OOB data was read, it called nand_read_page_op() to
reset the read cursor to the beginning of the page. This caused the
first page to be read twice: in that call, and later in the loop.
Address that issue by changing the call to nand_read_page_op() to
nand_change_read_column_op(), which will only reset the read cursor.
Cc: <stable@vger.kernel.org> # v5.2 Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740") Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-2-paul@crapouillou.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function nand_davinci_read_page_hwecc_oob_first() does read the ECC
data from the OOB area. Therefore it does not need to calculate the ECC
as it is already available.
Cc: <stable@vger.kernel.org> # v5.2 Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740") Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-1-paul@crapouillou.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not the child partition should be removed from the partition list
but the partition itself. Otherwise the partition list gets broken
and any subsequent remove operations leads to a kernel panic.
gpmi_io clock needs to be gated off when changing the parent/dividers of
enfc_clk_root (i.MX6Q/i.MX6UL) respectively qspi2_clk_root (i.MX6SX).
Otherwise this rate change can lead to an unresponsive GPMI core which
results in DMA timeouts and failed driver probe:
Other than stated in i.MX 6 erratum ERR007117, it should be sufficient
to gate only gpmi_io because all other bch/nand clocks are derived from
different clock roots.
The i.MX6 reference manuals state that changing clock muxers can cause
glitches but are silent about changing dividers. But tests showed that
these glitches can definitely happen on i.MX6ULL. For i.MX7D/8MM in turn,
the manual guarantees that no glitches can happen when changing
dividers.
Co-developed-by: Stefan Riedmueller <s.riedmueller@phytec.de> Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> Signed-off-by: Christian Eggers <ceggers@arri.de> Cc: stable@vger.kernel.org Acked-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-2-ceggers@arri.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot detected a NULL pointer dereference of nfc_llcp_sock->dev pointer
(which is a 'struct nfc_dev *') with calls to llcp_sock_sendmsg() after
a failed llcp_sock_bind(). The message being sent is a SOCK_DGRAM.
KASAN report:
BUG: KASAN: null-ptr-deref in nfc_alloc_send_skb+0x2d/0xc0
Read of size 4 at addr 00000000000005c8 by task llcp_sock_nfc_a/899
The issue was visible only with multiple simultaneous calls to bind() and
sendmsg(), which resulted in most of the bind() calls to fail. The
bind() was failing on checking if there is available WKS/SDP/SAP
(respective bit in 'struct nfc_llcp_local' fields). When there was no
available WKS/SDP/SAP, the bind returned error but the sendmsg() to such
socket was able to trigger mentioned NULL pointer dereference of
nfc_llcp_sock->dev.
The code looks simply racy and currently it protects several paths
against race with checks for (!nfc_llcp_sock->local) which is NULL-ified
in error paths of bind(). The llcp_sock_sendmsg() did not have such
check but called function nfc_llcp_send_ui_frame() had, although not
protected with lock_sock().
Therefore the race could look like (same socket is used all the time):
CPU0 CPU1
==== ====
llcp_sock_bind()
- lock_sock()
- success
- release_sock()
- return 0
llcp_sock_sendmsg()
- lock_sock()
- release_sock()
llcp_sock_bind(), same socket
- lock_sock()
- error
- nfc_llcp_send_ui_frame()
- if (!llcp_sock->local)
- llcp_sock->local = NULL
- nfc_put_device(dev)
- dereference llcp_sock->dev
- release_sock()
- return -ERRNO
The nfc_llcp_send_ui_frame() checked llcp_sock->local outside of the
lock, which is racy and ineffective check. Instead, its caller
llcp_sock_sendmsg(), should perform the check inside lock_sock().
Reported-and-tested-by: syzbot+7f23bcddf626e0593a39@syzkaller.appspotmail.com Fixes: b874dec21d1c ("NFC: Implement LLCP connection less Tx path") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In fuzzed image, SSA table may indicate that a data block belongs to
invalid node, which node ID is out-of-range (0, 1, 2 or max_nid), in
order to avoid migrating inconsistent data in such corrupted image,
let's do sanity check anyway before data block migration.
F2FS-fs (loop0): sanity_check_inode: inode (ino=49) extent info [5942, 4294180864, 4] is incorrect, run fsck to fix
F2FS-fs (loop0): f2fs_check_nid_range: out-of-range nid=31340049, run fsck to fix.
BUG: kernel NULL pointer dereference, address: 0000000000000000
folio_mark_dirty+0x33/0x50
move_data_page+0x2dd/0x460 [f2fs]
do_garbage_collect+0xc18/0x16a0 [f2fs]
f2fs_gc+0x1d3/0xd90 [f2fs]
f2fs_balance_fs+0x13a/0x570 [f2fs]
f2fs_create+0x285/0x840 [f2fs]
path_openat+0xe6d/0x1040
do_filp_open+0xc5/0x140
do_sys_openat2+0x23a/0x310
do_sys_open+0x57/0x80
The root cause is for special file: e.g. character, block, fifo or socket file,
f2fs doesn't assign address space operations pointer array for mapping->a_ops field,
so, in a fuzzed image, SSA table indicates a data block belong to special file, when
f2fs tries to migrate that block, it causes NULL pointer access once move_data_page()
calls a_ops->set_dirty_page().
Cc: stable@vger.kernel.org Reported-by: Wenqing Liu <wenqingliu0120@gmail.com> Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some weird devices set the codec SSID vendor ID 0, and
snd_pci_quirk_lookup_id() loop aborts at the point although it should
still try matching with the SSID device ID. This resulted in a
missing quirk for some old Macs.
Fix the loop termination condition to check both subvendor and
subdevice.
If we ever see a touch report with contact count data we initialize
several variables used to read the contact count in the pre-report
phase. These variables are never reset if we process a report which
doesn't contain a contact count, however. This can cause the pre-
report function to trigger a read of arbitrary memory (e.g. NULL
if we're lucky) and potentially crash the driver.
This commit restores resetting of the variables back to default
"none" values that were used prior to the commit mentioned
below.
AES hardware may internally re-classify a contact that it thought was
intentional as a palm. Intentional contacts are reported as "down" with
the confidence bit set. When this re-classification occurs, however, the
state transitions to "up" with the confidence bit cleared. This kind of
transition appears to be legal according to Microsoft docs, but we do
not handle it correctly. Because the confidence bit is clear, we don't
call `wacom_wac_finger_slot` and update userspace. This causes hung
touches that confuse userspace and interfere with pen arbitration.
This commit adds a special case to ignore the confidence flag if a contact
is reported as removed. This ensures we do not leave a hung touch if one
of these re-classification events occured. Ideally we'd have some way to
also let userspace know that the touch has been re-classified as a palm
and needs to be canceled, but that's not possible right now :)
Link: https://github.com/linuxwacom/input-wacom/issues/288 Fixes: 7fb0413baa7f (HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts) CC: stable@vger.kernel.org Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Reviewed-by: Ping Cheng <ping.cheng@wacom.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two values go hand-in-hand and must be valid for the driver to
behave correctly. We are currently lazy about updating the values and
rely on the "expected" code flow to take care of making sure they're
valid at the point they're needed. The "expected" flow changed somewhat
with commit f8b6a74719b5 ("HID: wacom: generic: Support multiple tools
per report"), however. This led to problems with the DTH-2452 due (in
part) to *all* contacts being fully processed -- even those past the
expected contact count. Specifically, the received count gets reset to
0 once all expected fingers are processed, but not the expected count.
The rest of the contacts in the report are then *also* processed since
now the driver thinks we've only processed 0 of N expected contacts.
Later commits such as 7fb0413baa7f (HID: wacom: Use "Confidence" flag to
prevent reporting invalid contacts) worked around the DTH-2452 issue by
skipping the invalid contacts at the end of the report, but this is not
a complete fix. The confidence flag cannot be relied on when a contact
is removed (see the following patch), and dealing with that condition
re-introduces the DTH-2452 issue unless we also address this contact
count laziness. By resetting expected and received counts at the same
time we ensure the driver understands that there are 0 more contacts
expected in the report. Similarly, we also make sure to reset the
received count if for some reason we're out of sync in the pre-report
phase.
Link: https://github.com/linuxwacom/input-wacom/issues/288 Fixes: f8b6a74719b5 ("HID: wacom: generic: Support multiple tools per report") CC: stable@vger.kernel.org Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Reviewed-by: Ping Cheng <ping.cheng@wacom.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uhid has to run hid_add_device() from workqueue context while allowing
parallel use of the userspace API (which is protected with ->devlock).
But hid_add_device() can fail. Currently, that is handled by immediately
destroying the associated HID device, without using ->devlock - but if
there are concurrent requests from userspace, that's wrong and leads to
NULL dereferences and/or memory corruption (via use-after-free).
Fix it by leaving the HID device as-is in the worker. We can clean it up
later, either in the UHID_DESTROY command handler or in the ->release()
handler.
Battery status on Elan tablet driver is reported for the HP ENVY x360
15t-dr100. There is no separate battery for the Elan controller resulting in a
battery level report of 0% or 1% depending on whether a stylus has interacted
with the screen. These low battery level reports causes a variety of bad
behavior in desktop environments. This patch adds the appropriate quirk to
indicate that the batery status is unused for this target.
When the TDP MMU is write-protection GFNs for page table protection (as
opposed to for dirty logging, or due to the HVA not being writable), it
checks if the SPTE is already write-protected and if so skips modifying
the SPTE and the TLB flush.
This behavior is incorrect because it fails to check if the SPTE
is write-protected for page table protection, i.e. fails to check
that MMU-writable is '0'. If the SPTE was write-protected for dirty
logging but not page table protection, the SPTE could locklessly be made
writable, and vCPUs could still be running with writable mappings cached
in their TLB.
Fix this by only skipping setting the SPTE if the SPTE is already
write-protected *and* MMU-writable is already clear. Technically,
checking only MMU-writable would suffice; a SPTE cannot be writable
without MMU-writable being set. But check both to be paranoid and
because it arguably yields more readable code.
Fixes: 46044f72c382 ("kvm: x86/mmu: Support write protection for nesting in tdp MMU") Cc: stable@vger.kernel.org Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20220113233020.3986005-2-dmatlack@google.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Legion Y9000X 2020 has a speaker, but the speaker doesn't work.
This can be fixed by applying alc285_fixup_ideapad_s740_coef
to fix the speaker's coefficients.
Besides, to support the transition between the speaker and the headphone,
alc287_fixup_legion_15imhg05_speakers needs to be run.
projects / thirdparty / kernel / stable.git / log
