The next call to sii8620_burst_get_tx_buf will result in off-by-one
When ctx->burst.tx_count + size == ARRAY_SIZE(ctx->burst.tx_buf). The same
thing happens in sii8620_burst_get_rx_buf.
This patch also change tx_count and tx_buf to rx_count and rx_buf in
sii8620_burst_get_rx_buf. It is unreasonable to check tx_buf's size and
use rx_buf.
Fixes: e19e9c692f81 ("drm/bridge/sii8620: add support for burst eMSC transmissions") Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220518065856.18936-1-hbh25y@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
It's possible for users to try to duplicate the CRTC state even when the
state doesn't exist. drm_atomic_helper_crtc_duplicate_state() (and other
users of __drm_atomic_helper_crtc_duplicate_state()) already guard this
with a WARN_ON() instead of crashing, so let's do that here too.
The divider calculations tried to find the divider just faster than the
clock requested. However if it required a divider of 7 then the for loop
aborted without handling the "error" case, and could end up with a clock
lower than requested.
The integer divider from parent PLL to DSI clock is also capable of
going up to /255, not just /7 that the driver was trying. This allows
for slower link frequencies on the DSI bus where the resolution permits.
Correct the loop so that we always have a clock greater than requested,
and covering the whole range of dividers.
Fixes: 86c1b9eff3f2 ("drm/vc4: Adjust modes in DSI to work around the integer PLL divider.") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-13-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Error return values are supposed to be negative in hdpvr_read. Most
error returns are currently handled via an unsigned integer "ret". When
setting a negative error value to "ret", the value actually becomes a
large positive value, because "ret" is unsigned. Later on, the "ret"
value is returned. But as ssize_t is a 64-bit signed number, the error
return value stays a large positive integer instead of a negative
integer. This can cause an error value to be interpreted as the read
size, which can cause a buffer overread for applications relying on the
returned size.
Fixes: 9aba42efe85b ("V4L/DVB (11096): V4L2 Driver for the Hauppauge HD PVR usb capture device") Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As mipi_dsi_driver_register could return error if fails,
it should be better to check the return value and return error
if fails.
Moreover, if i2c_add_driver fails, mipi_dsi_driver_register
should be reverted.
As a result of the execution of the inner while loop, the value
of 'idx' can be equal to LINK_QUAL_MAX_RETRY_NUM. However, this
is not checked after the loop and 'idx' is used to write the
LINK_QUAL_MAX_RETRY_NUM size array 'lq_cmd->rs_table[idx]' below
in the outer loop.
The fix is to check the new value of 'idx' inside the nested loop,
and break both loops if index equals the size. Checking it at the
start is now pointless, so let's remove it.
Detected using the static analysis tool - Svace.
Fixes: be663ab67077 ("iwlwifi: split the drivers for agn and legacy devices 3945/4965") Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220608171614.28891-1-aleksei.kodanev@bell-sw.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to not add fancy protection for drv_priv we can move
htc_handle->drv_priv initialization at the end of the
ath9k_htc_probe_device() and add helper macro to make
all *_STAT_* macros NULL safe, since syzbot has reported related NULL
deref in that macros [1]
We got the following warning when booting the kernel:
[ 3.243674] INFO: trying to register non-static key.
[ 3.243922] The code is fine but needs lockdep annotation, or maybe
[ 3.244230] you didn't initialize this object before use?
[ 3.245642] Call Trace:
[ 3.247836] lock_acquire+0xff/0x2d0
[ 3.248727] tw686x_audio_irq+0x1a5/0xcc0 [tw686x]
[ 3.249211] tw686x_irq+0x1f9/0x480 [tw686x]
The lock 'vc->qlock' will be initialized in tw686x_video_init(), but the
driver registers the irq before calling the tw686x_video_init(), and we
got the warning.
Fix this by registering the irq at the end of probe
Fixes: 704a84ccdbf1 ("[media] media: Support Intersil/Techwell TW686x-based video capture cards") Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the dsi_enable function, mtk_dsi_rxtx_control is to
pull up the MIPI signal operation. Before dsi_disable,
MIPI should also be pulled down by writing a register
instead of disabling dsi.
If disable dsi without pulling the mipi signal low, the value of
the register will still maintain the setting of the mipi signal being
pulled high.
After resume, even if the mipi signal is not pulled high, it will still
be in the high state.
The last case label can write two buffers 'mc_reg_address[j]' and
'mc_data[j]' with 'j' offset equal to SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE
since there are no checks for this value in both case labels after the
last 'j++'.
Instead of changing '>' to '>=' there, add the bounds check at the start
of the second 'case' (the first one already has it).
Also, remove redundant last checks for 'j' index bigger than array size.
The expression is always false. Moreover, before or after the patch
'table->last' can be equal to SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE and it
seems it can be a valid value.
Detected using the static analysis tool - Svace. Fixes: 69e0b57a91ad ("drm/radeon/kms: add dpm support for cayman (v5)") Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the copy_from_user() fails or the user gives invalid date then the
correct thing to do is to return a negative error code. (Currently it
returns success).
I made a copy additional related cleanups:
1) There is no need to check "buffer" for NULL. That's handled by
copy_from_user().
2) The "h2c_len" variable cannot be negative because it is unsigned
and because sscanf() does not return negative error codes.
Fixes: 610247f46feb ("rtlwifi: Improve debugging by using debugfs") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/YoOLnDkHgVltyXK7@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge rising - but instead rely on Devicetree to configure it.
All Qualcomm DTSI with WCN3990 define the interrupt type as level high,
so the mismatch between DTSI and driver causes rebind issues:
$ echo 18800000.wifi > /sys/bus/platform/drivers/ath10k_snoc/unbind
$ echo 18800000.wifi > /sys/bus/platform/drivers/ath10k_snoc/bind
[ 44.763114] irq: type mismatch, failed to map hwirq-446 for interrupt-controller@17a00000!
[ 44.763130] ath10k_snoc 18800000.wifi: error -ENXIO: IRQ index 0 not found
[ 44.763140] ath10k_snoc 18800000.wifi: failed to initialize resource: -6
Include sys/time.h and pthread.h in tmon.h, so that types
"pthread_mutex_t" and "struct timeval tv" are known when tmon.h
references them.
Without these headers, compiling tmon against musl-libc will fail with
these errors:
In file included from sysfs.c:31:0:
tmon.h:47:8: error: unknown type name 'pthread_mutex_t'
extern pthread_mutex_t input_lock;
^~~~~~~~~~~~~~~
make[3]: *** [<builtin>: sysfs.o] Error 1
make[3]: *** Waiting for unfinished jobs....
In file included from tui.c:31:0:
tmon.h:54:17: error: field 'tv' has incomplete type
struct timeval tv;
^~
make[3]: *** [<builtin>: tui.o] Error 1
make[2]: *** [Makefile:83: tmon] Error 2
Signed-off-by: Markus Mayer <mmayer@broadcom.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Acked-by: Alejandro González <alejandro.gonzalez.correo@gmail.com> Tested-by: Alejandro González <alejandro.gonzalez.correo@gmail.com> Fixes: 94f69966faf8 ("tools/thermal: Introduce tmon, a tool for thermal subsystem") Link: https://lore.kernel.org/r/20220718031040.44714-1-f.fainelli@gmail.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
dequeue_task_rt() only decrements 'rt_rq->rt_nr_running' after having
called sched_update_tick_dependency() preventing it from re-enabling the
tick on systems that no longer have pending SCHED_RT tasks but have
multiple runnable SCHED_OTHER tasks:
Every other scheduler class performs the operation in the opposite
order, and sched_update_tick_dependency() expects the values to be
updated as such. So avoid the misbehaviour by inverting the order in
which the above operations are performed in the RT scheduler.
Fixes: 76d92ac305f2 ("sched: Migrate sched to use new tick dependency mask model") Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Valentin Schneider <vschneid@redhat.com> Reviewed-by: Phil Auld <pauld@redhat.com> Link: https://lore.kernel.org/r/20220628092259.330171-1-nsaenzju@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
We should call the of_node_put() for the reference returned by
of_get_child_by_name() which has increased the refcount.
Fixes: 40e20d68bb3f ("regulator: of: Add support for parsing regulator_state for suspend state") Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20220715111027.391032-1-windhl@126.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The smem-state properties for the pronto node were incorrectly labelled,
reading `qcom,state*` rather than `qcom,smem-state*`. Fix that, allowing
the stop state to be used.
In error case in hisi_lpc_acpi_probe() after calling platform_device_add(),
hisi_lpc_acpi_remove() can't release the failed 'pdev', so it will be leak,
call platform_device_put() to fix this problem.
I'v constructed this error case and tested this patch on D05 board.
Fixes: 99c0228d6ff1 ("HISI LPC: Re-Add ACPI child enumeration support") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 00f7dc636366 ("ARM: zynq: Add support for SOC_BUS") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220605082807.21526-1-linmq006@gmail.com Signed-off-by: Michal Simek <michal.simek@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 1e037794f7f0 ("ARM: OMAP3+: PRM: register interrupt information from DT") Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220526073724.21169-1-linmq006@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 5e68c0fc8df8 ("soc: amlogic: Add Meson6/Meson8/Meson8b/Meson8m2 SoC Information driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20220524065729.33689-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When offset is larger than the size of the bit array, we should not
attempt to access the array as we can perform an access beyond the
end of the array. Fix this by changing the pre-condition.
Using "cmp r2, r1; bhs ..." covers us for the size == 0 case, since
this will always take the branch when r1 is zero, irrespective of
the value of r2. This means we can fix this bug without adding any
additional code!
Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is reporting hung task at misc_open() [1], for there is a race
window of AB-BA deadlock which involves probe_count variable. Currently
wait_for_device_probe() from snapshot_open() from misc_open() can sleep
forever with misc_mtx held if probe_count cannot become 0.
When a device is probed by hub_event() work function, probe_count is
incremented before the probe function starts, and probe_count is
decremented after the probe function completed.
There are three cases that can prevent probe_count from dropping to 0.
(a) A device being probed stopped responding (i.e. broken/malicious
hardware).
(b) A process emulating a USB device using /dev/raw-gadget interface
stopped responding for some reason.
(c) New device probe requests keeps coming in before existing device
probe requests complete.
The phenomenon syzbot is reporting is (b). A process which is holding
system_transition_mutex and misc_mtx is waiting for probe_count to become
0 inside wait_for_device_probe(), but the probe function which is called
from hub_event() work function is waiting for the processes which are
blocked at mutex_lock(&misc_mtx) to respond via /dev/raw-gadget interface.
This patch mitigates (b) by deferring wait_for_device_probe() from
snapshot_open() to snapshot_write() and snapshot_ioctl(). Please note that
the possibility of (b) remains as long as any thread which is emulating a
USB device via /dev/raw-gadget interface can be blocked by uninterruptible
blocking operations (e.g. mutex_lock()).
Please also note that (a) and (c) are not addressed. Regarding (c), we
should change the code to wait for only one device which contains the
image for resuming from hibernation. I don't know how to address (a), for
use of timeout for wait_for_device_probe() might result in loss of user
data in the image. Maybe we should require the userland to wait for the
image device before opening /dev/snapshot interface.
But, Lenovo G40-45, a platform released in 2015, still needs NVS memory
saving during S3. A quirk is introduced for this platform.
Signed-off-by: Manyi Li <limanyi@uniontech.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Somehow the "ThinkPad X1 Carbon 6th" entry ended up twice in the
struct dmi_system_id acpi_ec_no_wakeup[] array. Remove one of
the entries.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In omapdss_init_fbdev(), of_find_node_by_name() will return a node
pointer with refcount incremented. We should use of_node_put() when
it is not used anymore.
Signed-off-by: Liang He <windhl@126.com>
Message-Id: <20220617145803.4050918-1-windhl@126.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
imx6ul is not compatible to imx6sx, both have different erratas.
Fixes the dt_binding_check warning:
spi@21e0000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-qspi', 'fsl,imx6sx-qspi'] is too long
Additional items are not allowed ('fsl,imx6sx-qspi' was unexpected)
'fsl,imx6ul-qspi' is not one of ['fsl,ls1043a-qspi']
'fsl,imx6ul-qspi' is not one of ['fsl,imx8mq-qspi']
'fsl,ls1021a-qspi' was expected
'fsl,imx7d-qspi' was expected
In yaml binding "fsl,imx6ul-lcdif" is listed as compatible to imx6sx-lcdif,
but not imx28-lcdif. Change the list accordingly. Fixes the
dt_binding_check warning:
lcdif@21c8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-lcdif', 'fsl,imx28-lcdif'] is too long
Additional items are not allowed ('fsl,imx28-lcdif' was unexpected)
'fsl,imx6ul-lcdif' is not one of ['fsl,imx23-lcdif', 'fsl,imx28-lcdif',
'fsl,imx6sx-lcdif']
'fsl,imx6sx-lcdif' was expected
operating-points is a uint32-matrix as per opp-v1.yaml. Change it
accordingly. While at it, change fsl,soc-operating-points as well,
although there is no bindings file (yet). But they should have the same
format. Fixes the dt_binding_check warning:
cpu@0: operating-points:0: [696000, 1275000, 528000, 1175000, 396000, 1025000, 198000, 950000] is too long
cpu@0: operating-points:0: Additional items are not allowed (528000, 1175000, 396000, 1025000, 198000, 950000 were unexpected)
All 3 properties are required by sram.yaml. Fixes the dtbs_check
warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Add checks verifying number of inodes stored in the superblock matches
the number computed from number of inodes per group. Also verify we have
at least one block worth of inodes per group. This prevents crashes on
corrupted filesystems.
Reported-by: syzbot+d273f7d7f58afd93be48@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
To fix this issue, keep the table->data as &insn->current_mode and
use container_of() to retrieve the insn pointer. Another mutex is
used to protect against the current_mode update but not for retrieving
insn_emulation as table->data is no longer changing.
Enable tracing of the execve*() system calls with the
syscalls:sys_exit_execve tracepoint by removing the call to
forget_syscall() when starting a new thread and preserving the value of
regs->syscallno across exec.
In nf_tables_updtable, if nf_tables_table_enable returns an error,
nft_trans_destroy is called to free the transaction object.
nft_trans_destroy() calls list_del(), but the transaction was never
placed on a list -- the list head is all zeroes, this results in
a null dereference:
BUG: KASAN: null-ptr-deref in nft_trans_destroy+0x26/0x59
Call Trace:
nft_trans_destroy+0x26/0x59
nf_tables_newtable+0x4bc/0x9bc
[..]
Its sane to assume that nft_trans_destroy() can be called
on the transaction object returned by nft_trans_alloc(), so
make sure the list head is initialised.
Fixes: 55dd6f93076b ("netfilter: nf_tables: use new transaction infrastructure to handle table") Reported-by: mingi cho <mgcho.minic@gmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When doing lookups for sets on the same batch by using its ID, a set from a
different table can be used.
Then, when the table is removed, a reference to the set may be kept after
the set is freed, leading to a potential use-after-free.
When looking for sets by ID, use the table that was used for the lookup by
name, and only return sets belonging to that same table.
This fixes CVE-2022-2586, also reported as ZDI-CAN-17470.
Reported-by: Team Orca of Sea Security (@seasecresponse) Fixes: 958bee14d071 ("netfilter: nf_tables: use new transaction infrastructure to handle sets") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usb core introduce the mechanism of giveback of URB in tasklet context to
reduce hardware interrupt handling time. On some test situation(such as
FIO with 4KB block size), when tasklet callback function called to
giveback URB, interrupt handler add URB node to the bh->head list also.
If check bh->head list again after finish all URB giveback of local_list,
then it may introduce a "dynamic balance" between giveback URB and add URB
to bh->head list. This tasklet callback function may not exit for a long
time, which will cause other tasklet function calls to be delayed. Some
real-time applications(such as KB and Mouse) will see noticeable lag.
In order to prevent the tasklet function from occupying the cpu for a long
time at a time, new URBS will not be added to the local_list even though
the bh->head list is not empty. But also need to ensure the left URB
giveback to be processed in time, so add a member high_prio for structure
giveback_urb_bh to prioritize tasklet and schelule this tasklet again if
bh->head list is not empty.
At the same time, we are able to prioritize tasklet through structure
member high_prio. So, replace the local high_prio_bh variable with this
structure member in usb_hcd_giveback_urb.
Fixes: 94dfd7edfd5c ("USB: HCD: support giveback of URB in tasklet context") Cc: stable <stable@kernel.org> Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com> Link: https://lore.kernel.org/r/20220726074918.5114-1-WeitaoWang-oc@zhaoxin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_CPUMASK_OFFSTACK and CONFIG_DEBUG_PER_CPU_MAPS is selected,
cpu_max_bits_warn() generates a runtime warning similar as below while
we show /proc/cpuinfo. Fix this by using nr_cpu_ids (the runtime limit)
instead of NR_CPUS to iterate CPUs.
On a bare-metal Power8 system that doesn't have an "ibm,power-rng", a
malicious QEMU and guest that ignore the absence of the
KVM_CAP_PPC_HWRNG flag, and calls H_RANDOM anyway, will dereference a
NULL pointer.
In practice all Power8 machines have an "ibm,power-rng", but let's not
rely on that, add a NULL check and early return in
powernv_get_random_real_mode().
Fixes: e928e9cb3601 ("KVM: PPC: Book3S HV: Add fast real-mode H_RANDOM implementation.") Cc: stable@vger.kernel.org # v4.1+ Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220727143219.2684192-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default old pre-3.0 Freescale PCIe controllers reports invalid PCI Class
Code 0x0b20 for PCIe Root Port. It can be seen by lspci -b output on P2020
board which has this pre-3.0 controller:
$ lspci -bvnn
00:00.0 Power PC [0b20]: Freescale Semiconductor Inc P2020E [1957:0070] (rev 21)
!!! Invalid class 0b20 for header type 01
Capabilities: [4c] Express Root Port (Slot-), MSI 00
Fix this issue by programming correct PCI Class Code 0x0604 for PCIe Root
Port to the Freescale specific PCIe register 0x474.
Fix activated by U-Boot stay active also after booting Linux kernel.
But boards which use older U-Boot version without that fix are affected and
still require this fix.
So implement this class code fix also in kernel fsl_pci.c driver.
test_bit(), as any other bitmap op, takes `unsigned long *` as a
second argument (pointer to the actual bitmap), as any bitmap
itself is an array of unsigned longs. However, the ia64_get_irr()
code passes a ref to `u64` as a second argument.
This works with the ia64 bitops implementation due to that they
have `void *` as the second argument and then cast it later on.
This works with the bitmap API itself due to that `unsigned long`
has the same size on ia64 as `u64` (`unsigned long long`), but
from the compiler PoV those two are different.
Define @irr as `unsigned long` to fix that. That implies no
functional changes. Has been hidden for 16 years!
There's a KASAN warning in raid10_remove_disk when running the lvm
test lvconvert-raid-reshape.sh. We fix this warning by verifying that the
value "number" is valid.
BUG: KASAN: slab-out-of-bounds in raid10_remove_disk+0x61/0x2a0 [raid10]
Read of size 8 at addr ffff889108f3d300 by task mdX_raid10/124682
Last potentially related work creation:
kasan_save_stack+0x1e/0x40
__kasan_record_aux_stack+0x9e/0xc0
kvfree_call_rcu+0x84/0x480
timerfd_release+0x82/0x140
L __fput+0xfa/0x400
task_work_run+0x80/0xc0
exit_to_user_mode_prepare+0x155/0x160
syscall_exit_to_user_mode+0x12/0x40
do_syscall_64+0x42/0xc0
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Second to last potentially related work creation:
kasan_save_stack+0x1e/0x40
__kasan_record_aux_stack+0x9e/0xc0
kvfree_call_rcu+0x84/0x480
timerfd_release+0x82/0x140
__fput+0xfa/0x400
task_work_run+0x80/0xc0
exit_to_user_mode_prepare+0x155/0x160
syscall_exit_to_user_mode+0x12/0x40
do_syscall_64+0x42/0xc0
entry_SYSCALL_64_after_hwframe+0x46/0xb0
The buggy address belongs to the object at ffff889108f3d200
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 0 bytes to the right of
256-byte region [ffff889108f3d200, ffff889108f3d300)
Memory state around the buggy address: ffff889108f3d200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff889108f3d280: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff889108f3d300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff889108f3d380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff889108f3d400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver use the non-managed form of the register function in
isl29028_remove(). To keep the release order as mirroring the ordering
in probe, the driver should use non-managed form in probe, too.
Currently, for all op verification we call __red_deduce_bounds() and
__red_bound_offset() but we only call __update_reg_bounds() in bitwise
ops. However, we could benefit from calling __update_reg_bounds() in
BPF_ADD, BPF_SUB, and BPF_MUL cases as well.
For example, a register with state 'R1_w=invP0' when we subtract from
it,
w1 -= 2
Before coerce we will now have an smin_value=S64_MIN, smax_value=U64_MAX
and unsigned bounds umin_value=0, umax_value=U64_MAX. These will then
be clamped to S32_MIN, U32_MAX values by coerce in the case of alu32 op
as done in above example. However tnum will be a constant because the
ALU op is done on a constant.
Without update_reg_bounds() we have a scenario where tnum is a const
but our unsigned bounds do not reflect this. By calling update_reg_bounds
after coerce to 32bit we further refine the umin_value to U64_MAX in the
alu64 case or U32_MAX in the alu32 case above.
When pinning a buffer, we should check to see if there are any
additional restrictions imposed by bo->preferred_domains. This will
prevent the BO from being moved to an invalid domain when pinning.
For example, this can happen if the user requests to create a BO in GTT
domain for display scanout. amdgpu_dm will allow pinning to either VRAM
or GTT domains, since DCN can scanout from either or. However, in
amdgpu_bo_pin_restricted(), pinning to VRAM is preferred if there is
adequate carveout. This can lead to pinning to VRAM despite the user
requesting GTT placement for the BO.
v2: Allow the kernel to override the domain, which can happen when
exporting a BO to a V4L camera (for example).
Signed-off-by: Leo Li <sunpeng.li@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the output of /proc/iomem to show the real hardware device name
including the pa_pathname, e.g. "Merlin 160 Core Centronics [8:16:0]".
Up to now only the pa_pathname ("[8:16.0]") was shown.
Some code paths cannot guarantee the inode have any dentry alias. So
WARN_ON() all !dentry may flood the kernel logs.
For example, when an overlayfs inode is watched by inotifywait (1), and
someone is trying to read the /proc/$(pidof inotifywait)/fdinfo/INOTIFY_FD,
at that time if the dentry has been reclaimed by kernel (such as
echo 2 > /proc/sys/vm/drop_caches), there will be a WARN_ON(). The
printed call stack would be like:
usbnet uses the work usbnet_deferred_kevent() to perform tasks which may
sleep. On disconnect, completion of the work was originally awaited in
->ndo_stop(). But in 2003, that was moved to ->disconnect() by historic
commit "[PATCH] USB: usbnet, prevent exotic rtnl deadlock":
The change was made because back then, the kernel's workqueue
implementation did not allow waiting for a single work. One had to wait
for completion of *all* work by calling flush_scheduled_work(), and that
could deadlock when waiting for usbnet_deferred_kevent() with rtnl_mutex
held in ->ndo_stop().
The commit solved one problem but created another: It causes a
use-after-free in USB Ethernet drivers aqc111.c, asix_devices.c,
ax88179_178a.c, ch9200.c and smsc75xx.c:
* If the drivers receive a link change interrupt immediately before
disconnect, they raise EVENT_LINK_RESET in their (non-sleepable)
->status() callback and schedule usbnet_deferred_kevent().
* usbnet_deferred_kevent() invokes the driver's ->link_reset() callback,
which calls netif_carrier_{on,off}().
* That in turn schedules the work linkwatch_event().
Because usbnet_deferred_kevent() is awaited after unregister_netdev(),
netif_carrier_{on,off}() may operate on an unregistered netdev and
linkwatch_event() may run after free_netdev(), causing a use-after-free.
In 2010, usbnet was changed to only wait for a single instance of
usbnet_deferred_kevent() instead of *all* work by commit 23f333a2bfaf
("drivers/net: don't use flush_scheduled_work()").
Unfortunately the commit neglected to move the wait back to
->ndo_stop(). Rectify that omission at long last.
The user may use the fbcon=vc:<n1>-<n2> option to tell fbcon to take
over the given range (n1...n2) of consoles. The value for n1 and n2
needs to be a positive number and up to (MAX_NR_CONSOLES - 1).
The given values were not fully checked against those boundaries yet.
To fix the issue, convert first_fb_vc and last_fb_vc to unsigned
integers and check them against the upper boundary, and make sure that
first_fb_vc is smaller than last_fb_vc.
If cooling_device_stats_setup() fails to create the stats object, it
must clear the last slot in cooling_device_attr_groups that was
initially empty (so as to make it possible to add stats attributes to
the cooling device attribute groups).
Failing to do so may cause the stats attributes to be created by
mistake for a device that doesn't have a stats object, because the
slot in question might be populated previously during the registration
of another cooling device.
Fixes: 8ea229511e06 ("thermal: Add cooling device's statistics in sysfs") Reported-by: Di Shen <di.shen@unisoc.com> Tested-by: Di Shen <di.shen@unisoc.com> Cc: 4.17+ <stable@vger.kernel.org> # 4.17+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All creation paths except for O_TMPFILE handle umask in the vfs directly
if the filesystem doesn't support or enable POSIX ACLs. If the filesystem
does then umask handling is deferred until posix_acl_create().
Because, O_TMPFILE misses umask handling in the vfs it will not honor
umask settings. Fix this by adding the missing umask handling.
Link: https://lore.kernel.org/r/1657779088-2242-2-git-send-email-xuyang2018.jy@fujitsu.com Fixes: 60545d0d4610 ("[O_TMPFILE] it's still short a few helpers, but infrastructure should be OK now...") Cc: <stable@vger.kernel.org> # 4.19+ Reported-by: Christian Brauner (Microsoft) <brauner@kernel.org> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Reviewed-and-Tested-by: Jeff Layton <jlayton@kernel.org> Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Yang Xu <xuyang2018.jy@fujitsu.com> Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If something manages to set the maximum file size to MAX_OFFSET+1, this
can cause the xfs and ext4 filesystems at least to become corrupt.
Ordinarily, the kernel protects against userspace trying this by
checking the value early in the truncate() and ftruncate() system calls
calls - but there are at least two places that this check is bypassed:
(1) Cachefiles will round up the EOF of the backing file to DIO block
size so as to allow DIO on the final block - but this might push
the offset negative. It then calls notify_change(), but this
inadvertently bypasses the checking. This can be triggered if
someone puts an 8EiB-1 file on a server for someone else to try and
access by, say, nfs.
(2) ksmbd doesn't check the value it is given in set_end_of_file_info()
and then calls vfs_truncate() directly - which also bypasses the
check.
In both cases, it is potentially possible for a network filesystem to
cause a disk filesystem to be corrupted: cachefiles in the client's
cache filesystem; ksmbd in the server's filesystem.
nfsd is okay as it checks the value, but we can then remove this check
too.
Fix this by adding a check to inode_newsize_ok(), as called from
setattr_prepare(), thereby catching the issue as filesystems set up to
perform the truncate with minimal opportunity for bypassing the new
check.
Fixes: 1f08c925e7a3 ("cachefiles: Implement backing file wrangling") Fixes: f44158485826 ("cifsd: add file operations") Signed-off-by: David Howells <dhowells@redhat.com> Reported-by: Jeff Layton <jlayton@kernel.org> Tested-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Namjae Jeon <linkinjeon@kernel.org> Cc: stable@kernel.org Acked-by: Alexander Viro <viro@zeniv.linux.org.uk>
cc: Steve French <sfrench@samba.org>
cc: Hyunchul Lee <hyc.lee@gmail.com>
cc: Chuck Lever <chuck.lever@oracle.com>
cc: Dave Wysochanski <dwysocha@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 12,1 model requires the same configuration as the 12,2 model
to enable headphones but has a different codec SSID. Adds
12,1 SSID for matching quirk.
There is another LENOVO 20149 (Type1Sku0) Notebook model with
CX20590, the device PCI SSID is 17aa:3977, which headphones are
not responding, that requires the quirk CXT_PINCFG_LENOVO_NOTEBOOK.
Add the corresponding entry to the quirk table.
When injecting a #GP on LLDT/LTR due to a non-canonical LDT/TSS base, set
the error code to the selector. Intel SDM's says nothing about the #GP,
but AMD's APM explicitly states that both LLDT and LTR set the error code
to the selector, not zero.
Note, a non-canonical memory operand on LLDT/LTR does generate a #GP(0),
but the KVM code in question is specific to the base from the descriptor.
Fixes: e37a75a13cda ("KVM: x86: Emulator ignores LDTR/TR extended base on LLDT/LTR") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Link: https://lore.kernel.org/r/20220711232750.1092012-3-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wait to mark the TSS as busy during LTR emulation until after all fault
checks for the LTR have passed. Specifically, don't mark the TSS busy if
the new TSS base is non-canonical.
Opportunistically drop the one-off !seg_desc.PRESENT check for TR as the
only reason for the early check was to avoid marking a !PRESENT TSS as
busy, i.e. the common !PRESENT is now done before setting the busy bit.
Don't BUG/WARN on interrupt injection due to GIF being cleared,
since it's trivial for userspace to force the situation via
KVM_SET_VCPU_EVENTS (even if having at least a WARN there would be correct
for KVM internally generated injections).
Touch switch state is received through WACOM_PAD_FIELD. However, it
is reported by touch_input. Don't register pad_input if no other pad
events require the interface.
Neither wait_on_buffer nor buffer_uptodate contain any memory barrier.
Consequently, if someone calls sb_bread and then reads the buffer data,
the read of buffer data may be executed before wait_on_buffer(bh) on
architectures with weak memory ordering and it may return invalid data.
Fix this bug by adding a memory barrier to set_buffer_uptodate and an
acquire barrier to buffer_uptodate (in a similar way as
folio_test_uptodate and folio_mark_uptodate).
We won't really have enough skbs to need a 64-bit cookie,
and on 32-bit platforms storing the 64-bit cookie into the
void *rate_driver_data doesn't work anyway. Switch back to
using just a 32-bit cookie and uintptr_t for the type to
avoid compiler warnings about all this.
Fixes: 4ee186fa7e40 ("wifi: mac80211_hwsim: fix race condition in pending packet") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Cc: Jeongik Cha <jeongik@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Users of GNU ld (BFD) from binutils 2.39+ will observe multiple
instances of a new warning when linking kernels in the form:
ld: warning: arch/x86/boot/pmjump.o: missing .note.GNU-stack section implies executable stack
ld: NOTE: This behaviour is deprecated and will be removed in a future version of the linker
ld: warning: arch/x86/boot/compressed/vmlinux has a LOAD segment with RWX permissions
Generally, we would like to avoid the stack being executable. Because
there could be a need for the stack to be executable, assembler sources
have to opt-in to this security feature via explicit creation of the
.note.GNU-stack feature (which compilers create by default) or command
line flag --noexecstack. Or we can simply tell the linker the
production of such sections is irrelevant and to link the stack as
--noexecstack.
LLVM's LLD linker defaults to -z noexecstack, so this flag isn't
strictly necessary when linking with LLD, only BFD, but it doesn't hurt
to be explicit here for all linkers IMO. --no-warn-rwx-segments is
currently BFD specific and only available in the current latest release,
so it's wrapped in an ld-option check.
While the kernel makes extensive usage of ELF sections, it doesn't use
permissions from ELF segments.
Users of GNU ld (BFD) from binutils 2.39+ will observe multiple
instances of a new warning when linking kernels in the form:
ld: warning: vmlinux: missing .note.GNU-stack section implies executable stack
ld: NOTE: This behaviour is deprecated and will be removed in a future version of the linker
ld: warning: vmlinux has a LOAD segment with RWX permissions
Generally, we would like to avoid the stack being executable. Because
there could be a need for the stack to be executable, assembler sources
have to opt-in to this security feature via explicit creation of the
.note.GNU-stack feature (which compilers create by default) or command
line flag --noexecstack. Or we can simply tell the linker the
production of such sections is irrelevant and to link the stack as
--noexecstack.
LLVM's LLD linker defaults to -z noexecstack, so this flag isn't
strictly necessary when linking with LLD, only BFD, but it doesn't hurt
to be explicit here for all linkers IMO. --no-warn-rwx-segments is
currently BFD specific and only available in the current latest release,
so it's wrapped in an ld-option check.
While the kernel makes extensive usage of ELF sections, it doesn't use
permissions from ELF segments.
RSB fill sequence does not have any protection for miss-prediction of
conditional branch at the end of the sequence. CPU can speculatively
execute code immediately after the sequence, while RSB filling hasn't
completed yet.
tl;dr: The Enhanced IBRS mitigation for Spectre v2 does not work as
documented for RET instructions after VM exits. Mitigate it with a new
one-entry RSB stuffing mechanism and a new LFENCE.
== Background ==
Indirect Branch Restricted Speculation (IBRS) was designed to help
mitigate Branch Target Injection and Speculative Store Bypass, i.e.
Spectre, attacks. IBRS prevents software run in less privileged modes
from affecting branch prediction in more privileged modes. IBRS requires
the MSR to be written on every privilege level change.
To overcome some of the performance issues of IBRS, Enhanced IBRS was
introduced. eIBRS is an "always on" IBRS, in other words, just turn
it on once instead of writing the MSR on every privilege level change.
When eIBRS is enabled, more privileged modes should be protected from
less privileged modes, including protecting VMMs from guests.
== Problem ==
Here's a simplification of how guests are run on Linux' KVM:
void run_kvm_guest(void)
{
// Prepare to run guest
VMRESUME();
// Clean up after guest runs
}
The execution flow for that would look something like this to the
processor:
1. Host-side: call run_kvm_guest()
2. Host-side: VMRESUME
3. Guest runs, does "CALL guest_function"
4. VM exit, host runs again
5. Host might make some "cleanup" function calls
6. Host-side: RET from run_kvm_guest()
Now, when back on the host, there are a couple of possible scenarios of
post-guest activity the host needs to do before executing host code:
* on pre-eIBRS hardware (legacy IBRS, or nothing at all), the RSB is not
touched and Linux has to do a 32-entry stuffing.
* on eIBRS hardware, VM exit with IBRS enabled, or restoring the host
IBRS=1 shortly after VM exit, has a documented side effect of flushing
the RSB except in this PBRSB situation where the software needs to stuff
the last RSB entry "by hand".
IOW, with eIBRS supported, host RET instructions should no longer be
influenced by guest behavior after the host retires a single CALL
instruction.
However, if the RET instructions are "unbalanced" with CALLs after a VM
exit as is the RET in #6, it might speculatively use the address for the
instruction after the CALL in #3 as an RSB prediction. This is a problem
since the (untrusted) guest controls this address.
Balanced CALL/RET instruction pairs such as in step #5 are not affected.
== Solution ==
The PBRSB issue affects a wide variety of Intel processors which
support eIBRS. But not all of them need mitigation. Today,
X86_FEATURE_RETPOLINE triggers an RSB filling sequence that mitigates
PBRSB. Systems setting RETPOLINE need no further mitigation - i.e.,
eIBRS systems which enable retpoline explicitly.
However, such systems (X86_FEATURE_IBRS_ENHANCED) do not set RETPOLINE
and most of them need a new mitigation.
Therefore, introduce a new feature flag X86_FEATURE_RSB_VMEXIT_LITE
which triggers a lighter-weight PBRSB mitigation versus RSB Filling at
vmexit.
The lighter-weight mitigation performs a CALL instruction which is
immediately followed by a speculative execution barrier (INT3). This
steers speculative execution to the barrier -- just like a retpoline
-- which ensures that speculation can never reach an unbalanced RET.
Then, ensure this CALL is retired before continuing execution with an
LFENCE.
In other words, the window of exposure is opened at VM exit where RET
behavior is troublesome. While the window is open, force RSB predictions
sampling for RET targets to a dead end at the INT3. Close the window
with the LFENCE.
There is a subset of eIBRS systems which are not vulnerable to PBRSB.
Add these systems to the cpu_vuln_whitelist[] as NO_EIBRS_PBRSB.
Future systems that aren't vulnerable will set ARCH_CAP_PBRSB_NO.
[ bp: Massage, incorporate review comments from Andy Cooper. ]
[ Pawan: Update commit message to replace RSB_VMEXIT with RETPOLINE ]
In do_adb_query() function of drivers/macintosh/adb.c, req->data is copied
form userland. The parameter "req->data[2]" is missing check, the array
size of adb_handler[] is 16, so adb_handler[req->data[2]].original_address and
adb_handler[req->data[2]].handler_id will lead to oob read.
Cc: stable <stable@kernel.org> Signed-off-by: Ning Qiang <sohu0106@126.com> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220713153734.2248-1-sohu0106@126.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Taking a recent change in the i8042 quirklist to this one: Clevo
board_names are somewhat unique, and if not: The generic Board_-/Sys_Vendor
string "Notebook" doesn't help much anyway. So identifying the devices just
by the board_name helps keeping the list significantly shorter and might
even hit more devices requiring the fix.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Fixes: c844d22fe0c0 ("ACPI: video: Force backlight native for Clevo NL5xRU and NL5xNU") Cc: All applicable <stable@vger.kernel.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TongFang PF5PU1G, PF4NU1F, PF5NU1G, and PF5LUXG/TUXEDO BA15 Gen10,
Pulse 14/15 Gen1, and Pulse 15 Gen2 have the same problem as the Clevo
NL5xRU and NL5xNU/TUXEDO Aura 15 Gen1 and Gen2:
They have a working native and video interface. However the default
detection mechanism first registers the video interface before
unregistering it again and switching to the native interface during boot.
This results in a dangling SBIOS request for backlight change for some
reason, causing the backlight to switch to ~2% once per boot on the first
power cord connect or disconnect event. Setting the native interface
explicitly circumvents this buggy behaviour by avoiding the unregistering
process.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Cc: All applicable <stable@vger.kernel.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When queuing I/O request to LLD, STS_RESOURCE may be returned because:
- Host is in recovery or blocked
- Target queue throttling or target is blocked
- LLD rejection
In these scenarios BLK_STS_DEV_RESOURCE is returned to the block layer to
avoid an unnecessary re-run of the queue. However, all of the requests
queued to this SCSI device may complete immediately after reading
'sdev->device_busy' and BLK_STS_DEV_RESOURCE is returned to block layer. In
that case the current I/O won't get a chance to get queued since it is
invisible at that time for both scsi_run_queue_async() and blk-mq's
RESTART.
Fix the issue by not returning BLK_STS_DEV_RESOURCE in this situation.
Link: https://lore.kernel.org/r/20201202100419.525144-1-ming.lei@redhat.com Fixes: 86ff7c2a80cd ("blk-mq: introduce BLK_STS_DEV_RESOURCE") Cc: Hannes Reinecke <hare@suse.com> Cc: Sumit Saxena <sumit.saxena@broadcom.com> Cc: Kashyap Desai <kashyap.desai@broadcom.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Ewan Milne <emilne@redhat.com> Cc: Long Li <longli@microsoft.com> Reported-by: John Garry <john.garry@huawei.com> Tested-by: "chenxiang (M)" <chenxiang66@hisilicon.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using 'perf mem' and 'perf c2c', an issue is observed that tool
reports the wrong offset for global data symbols. This is a common
issue on both x86 and Arm64 platforms.
Let's see an example, for a test program, below is the disassembly for
its .bss section which is dumped with objdump:
First we used 'perf mem record' to run the test program and then used
'perf --debug verbose=4 mem report' to observe what's the symbol info
for 'buf1' and 'buf2' structures.
The perf tool relies on libelf to parse symbols, in executable and
shared object files, 'st_value' holds a virtual address; 'sh_addr' is
the address at which section's first byte should reside in memory, and
'sh_offset' is the byte offset from the beginning of the file to the
first byte in the section. The perf tool uses below formula to convert
a symbol's memory address to a file address:
We can see the final adjusted address ranges for buf1 and buf2 are
[0x30a8-0x30e8) and [0x3068-0x30a8) respectively, apparently this is
incorrect, in the code, the structure for 'buf1' and 'buf2' specifies
compiler attribute with 64-byte alignment.
The problem happens for 'sh_offset', libelf returns it as 0x3028 which
is not 64-byte aligned, combining with disassembly, it's likely libelf
doesn't respect the alignment for .bss section, therefore, it doesn't
return the aligned value for 'sh_offset'.
Suggested by Fangrui Song, ELF file contains program header which
contains PT_LOAD segments, the fields p_vaddr and p_offset in PT_LOAD
segments contain the execution info. A better choice for converting
memory address to file address is using the formula:
file_address = st_value - p_vaddr + p_offset
This patch introduces elf_read_program_header() which returns the
program header based on the passed 'st_value', then it uses the formula
above to calculate the symbol file address; and the debugging log is
updated respectively.
There are sleep in atomic context bugs in timer handlers of sctp
such as sctp_generate_t3_rtx_event(), sctp_generate_probe_event(),
sctp_generate_t1_init_event(), sctp_generate_timeout_event(),
sctp_generate_t3_rtx_event() and so on.
The root cause is sctp_sched_prio_init_sid() with GFP_KERNEL parameter
that may sleep could be called by different timer handlers which is in
interrupt context.
One of the call paths that could trigger bug is shown below:
This patch changes gfp_t parameter of init_sid in sctp_sched_set_sched()
from GFP_KERNEL to GFP_ATOMIC in order to prevent sleep in atomic
context bugs.
Fix the inability to bring an interface up on a setup with
only MSI interrupts enabled (no MSI-X).
Solution is to add a default number of QPs = 1. This is enough,
since without MSI-X support driver enables only a basic feature set.
Fixes: bc6d33c8d93f ("i40e: Fix the number of queues available to be mapped for use") Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com> Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20220722175401.112572-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 1033990ac5b2 ("sctp: implement memory accounting on tx path"),
SCTP has supported memory accounting on tx path where 'sctp_wmem' is used
by sk_wmem_schedule(). So we should fix the description for this option in
ip-sysctl.rst accordingly.
v1->v2:
- Improve the description as Marcelo suggested.
Fixes: 1033990ac5b2 ("sctp: implement memory accounting on tx path") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_tcp_invalid_ratelimit, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 032ee4236954 ("tcp: helpers to mitigate ACK loops by rate-limiting out-of-window dupacks") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_tcp_autocorking, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: f54b311142a9 ("tcp: auto corking") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_tcp_min_rtt_wlen, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: f672258391b4 ("tcp: track min RTT using windowed min-filter") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
