Current state for the lan78xx driver does not allow for changing the
MAC address of the interface, without either removing the module (if
you compiled it that way) or rebooting the machine. If you attempt to
change the MAC address, ifconfig will show the new address, however,
the system/interface will not respond to any traffic using that
configuration. A few short-term options to work around this are to
unload the module and reload it with the new MAC address, change the
interface to "promisc", or reboot with the correct configuration to
change the MAC.
This patch enables the ability to change the MAC address via fairly normal means...
ifdown <interface>
modify entry in /etc/network/interfaces OR a similar method
ifup <interface>
Then test via any network communication, such as ICMP requests to gateway.
My only test platform for this patch has been a raspberry pi model 3b+.
Signed-off-by: Jason Martinsen <jasonmartinsen@msn.com>
-----
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure that we clear XPRT_CONNECTING before releasing the XPRT_LOCK so that
we don't have races between the (asynchronous) socket setup code and
tasks in xprt_connect().
In some case, when mac enable|disable and adjust link, may cause hard to
link(or abnormal) between mac and phy. This patch adds the code for rx PCS
to avoid this bug.
Disable the rx PCS when driver disable the gmac, and enable the rx PCS
when driver enable the mac.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ntuple-filters features is forced on by chip.
But it shows "ntuple-filters: off [fixed]" when use ethtool.
This patch make it correct with "ntuple-filters: on [fixed]".
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There will be a large number of MAC pause frames on the net,
which caused tx timeout of net device. And then the net device
was reset to try to recover it. So that is not useful, and will
cause some other problems.
So need doubled ndev->watchdog_timeo if device watchdog occurred
until watchdog_timeo up to 40s and then try resetting to recover
it.
When collecting dfx information such as hardware registers when tx timeout.
Some registers for count were cleared when read. So need move this task
before update net state which also read the count registers.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
1.In "hns_nic_init_irq", if request irq fail at index i,
the function return directly without releasing irq resources
that already requested.
2.In "hns_nic_net_up" after "hns_nic_init_irq",
if exceptional branch occurs, irqs that already requested
are not release.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If there are packets in hardware when changing the speed or duplex,
it may cause hardware hang up.
This patch adds the code to wait rx fbd clean up when ae stopped.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
After resetting dsaf to try to repair chip error such as ecc error,
the net device will be open if net interface is up. But at this time
if there is the users set the net device up with the command ifconfig,
the net device will be opened twice consecutively.
Function napi_enable was called when open device. And Kernel panic will
be occurred if it was called twice consecutively. Such as follow:
static inline void napi_enable(struct napi_struct *n)
{
BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
smp_mb__before_clear_bit();
clear_bit(NAPI_STATE_SCHED, &n->state);
}
This patchset fix this bug according to the flag NIC_STATE_DOWN.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the hip06 datasheet:
1.Six registers use wrong address:
RCB_COM_SF_CFG_INTMASK_RING
RCB_COM_SF_CFG_RING_STS
RCB_COM_SF_CFG_RING
RCB_COM_SF_CFG_INTMASK_BD
RCB_COM_SF_CFG_BD_RINT_STS
DSAF_INODE_VC1_IN_PKT_NUM_0_REG
2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be
0x103C + 0x80 * all_chn_num
3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG
is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be
overwrite
These registers are only used in "ethtool -d", so that did not cause ndev
to misfunction.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two test cases:
1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio,
and install them again, must use "ifconfig down/ifconfig up"
command pair to bring port to work.
This patch calls phy_stop function when init phy to fix this bug.
2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again,
all ports can not use anymore, because of the phy devices register
failed(phy devices already exists).
Phy devices are registered when hns_dsaf installed, this patch
removes them when hns_dsaf removed.
The two cases are sometimes related, fixing the second case also requires
fixing the first case, so fix them together.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the hip06 Datasheet:
1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num
2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The get_mac_address() function is normally inline, but when it is
not, we get a warning that this configuration is broken:
WARNING: vmlinux.o(.text+0x4aff00): Section mismatch in reference from the function w90p910_ether_setup() to the function .init.text:get_mac_address()
The function w90p910_ether_setup() references
the function __init get_mac_address().
This is often because w90p910_ether_setup lacks a __init
Remove the __init to make it always do the right thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning:
tentative array definition assumed to have one element
static const struct acpi_device_id xgene_enet_acpi_match[];
^
1 warning generated.
Both xgene_enet_acpi_match and xgene_enet_of_match are defined before
their uses at the bottom of the file so this is unnecessary. When
CONFIG_ACPI is disabled, ACPI_PTR becomes NULL so xgene_enet_acpi_match
doesn't need to be defined.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
csk leak can happen if a new TCP connection gets established after
cxgbit_accept_np() returns, to fix this leak free remaining csk in
cxgbit_free_np().
Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver sends update-SVID ramrod in the MFW notification path.
If there is a pending ramrod, driver doesn't retry the command
and storm firmware will never be updated with the SVID value.
The patch adds changes to send update-svid ramrod in process context with
retry/poll flags set.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Vlans are not getting removed when drivers are unloaded. The recent storm
firmware versions had added safeguards against re-configuring an already
configured vlan. As a result, PF inner reload flows (e.g., mtu change)
might trigger an assertion.
This change is going to remove vlans (same as we do for MACs) when doing
a chip cleanup during unload.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On some customer setups it was observed that shmem contains a non-zero fip
MAC for 57711 which would lead to enabling of SW FCoE.
Add a software workaround to clear the bad fip mac address if no FCoE
connections are supported.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the error handling block, nla_nest_cancel(skb, atd) is called to
cancel the nest operation. But then, ipset_nest_end(skb, atd) is
unexpected called to end the nest operation. This patch calls the
ipset_nest_end only on the branch that nla_nest_cancel is not called.
Fixes: 45040978c899 ("netfilter: ipset: Fix set:list type crash when flush/dump set in parallel") Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With PM enabled, I noticed that pressing a key on the droid4 keyboard will
block deeper idle states for the SoC. Let's fix this by using IRQF_ONESHOT
and stop constantly toggling the device OMAP4_KBD_IRQENABLE register as
suggested by Dmitry Torokhov <dmitry.torokhov@gmail.com>.
From the hardware point of view, looks like we need to manage the registers
for OMAP4_KBD_IRQENABLE and OMAP4_KBD_WAKEUPENABLE together to avoid
blocking deeper SoC idle states. And with toggling of OMAP4_KBD_IRQENABLE
register now gone with IRQF_ONESHOT, also the SoC idle state problem is
gone during runtime. We still also need to clear OMAP4_KBD_WAKEUPENABLE in
omap4_keypad_close() though to pair it with omap4_keypad_open() to prevent
blocking deeper SoC idle states after rmmod omap4-keypad.
Reported-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If "interface" is NULL then we can't release it and trying to will only
lead to an Oops.
Fixes: aea71a024914 ("[SCSI] bnx2fc: Introduce interface structure for each vlan interface") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When adjusting sack block sequence numbers, skb_make_writable() gets
called to make sure tcp options are all in the linear area, and buffer
is not shared.
This can cause tcp header pointer to get reallocated, so we must
reaload it to avoid memory corruption.
Right now, checkstack.pl isn't able to print anything on aarch64,
because it won't be able to match the stating objdump line of a function
due to this missing space. Hence, it displays every stack as zero-size.
After this patch, checkpatch.pl is able to match the start of a
function's objdump, and is then able to calculate each function's stack
correctly.
Link: http://lkml.kernel.org/r/20181207195843.38528-1-cai@lca.pw Signed-off-by: Qian Cai <cai@lca.pw> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sw2iso count should cover ARM LDO ramp-up time,
the MAX ARM LDO ramp-up time may be up to more than
100us on some boards, this patch sets sw2iso to 0xf
(~384us) which is the reset value, and it is much
more safe to cover different boards, since we have
observed that some customer boards failed with current
setting of 0x2.
Fixes: 05136f0897b5 ("ARM: imx: support arm power off in cpuidle for i.mx6sx") Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 6975a783d7b4 ("powerpc/boot: Allow building the zImage wrapper
as a relocatable ET_DYN", 2011-04-12) changed the procedure descriptor
at the start of crt0.S to have a hard-coded start address of 0x500000
rather than a reference to _zimage_start, presumably because having
a reference to a symbol introduced a relocation which is awkward to
handle in a position-independent executable. Unfortunately, what is
at 0x500000 in the COFF image is not the first instruction, but the
procedure descriptor itself, that is, a word containing 0x500000,
which is not a valid instruction. Hence, booting a COFF zImage
results in a "DEFAULT CATCH!, code=FFF00700" message from Open
Firmware.
This fixes the problem by (a) putting the procedure descriptor in the
data section and (b) adding a branch to _zimage_start as the first
instruction in the program.
Fixes: 6975a783d7b4 ("powerpc/boot: Allow building the zImage wrapper as a relocatable ET_DYN") Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
We just changed the code so we apply bias disable on the correct
register but forgot to align the register calculation. The result
is that we apply the change on the correct register, but possibly
at the incorrect offset/bit
This went undetected because offsets tends to be the same between
REG_PULL and REG_PULLEN for a given pin the EE controller. This
is not true for the AO controller.
Commit e82b0b382845 ("spi: bcm2835: Fix race on DMA termination") broke
the build with COMPILE_TEST=y on arches whose cmpxchg() requires 32-bit
operands (xtensa, older arm ISAs).
Fix by changing the dma_pending flag's type from bool to unsigned int.
Fixes: e82b0b382845 ("spi: bcm2835: Fix race on DMA termination") Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Martin Sperl <kernel@martin.sperl.org> Cc: Noralf Trønnes <noralf@tronnes.org> Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tpm_i2c_nuvoton calculated commands duration using TPM 1.x
values via tpm_calc_ordinal_duration() also for TPM 2.x chips.
Call tpm2_calc_ordinal_duration() for retrieving ordinal
duration for TPM 2.X chips.
Add the missing adjustment of the month range on alarm reads from the
RTC, correcting an issue coming from commit 9c6dfed92c3e ("rtc: m41t80:
add alarm functionality"). The range is 1-12 for hardware and 0-11 for
`struct rtc_time', and is already correctly handled on alarm writes to
the RTC.
It was correct up until commit 48e9766726eb ("drivers/rtc/rtc-m41t80.c:
remove disabled alarm functionality") too, which removed the previous
implementation of alarm support.
Although bit 31 of VTCR_EL2 is RES1, we inadvertently end up setting all
of the upper 32 bits to 1 as well because we define VTCR_EL2_RES1 as
signed, which is sign-extended when assigning to kvm->arch.vtcr.
Lucky for us, the architecture currently treats these upper bits as RES0
so, whilst we've been naughty, we haven't set fire to anything yet.
Cc: <stable@vger.kernel.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Christoffer Dall <christoffer.dall@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I was investigating an issue with seabios >= 1.10 which stopped working
for nested KVM on Hyper-V. The problem appears to be in
handle_ept_violation() function: when we do fast mmio we need to skip
the instruction so we do kvm_skip_emulated_instruction(). This, however,
depends on VM_EXIT_INSTRUCTION_LEN field being set correctly in VMCS.
However, this is not the case.
Intel's manual doesn't mandate VM_EXIT_INSTRUCTION_LEN to be set when
EPT MISCONFIG occurs. While on real hardware it was observed to be set,
some hypervisors follow the spec and don't set it; we end up advancing
IP with some random value.
I checked with Microsoft and they confirmed they don't fill
VM_EXIT_INSTRUCTION_LEN on EPT MISCONFIG.
Fix the issue by doing instruction skip through emulator when running
nested.
Fixes: 68c3b4d1676d870f0453c31d5a52e7e65c7448ae Suggested-by: Radim Krčmář <rkrcmar@redhat.com> Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
[mhaboustak: backport to 4.9.y] Signed-off-by: Mike Haboustak <haboustak@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While resolving a bug with locks on samba shares found a strange behavior.
When a file locked by one node and we trying to lock it from another node
it fail with errno 5 (EIO) but in that case errno must be set to
(EACCES | EAGAIN).
This isn't happening when we try to lock file second time on same node.
In this case it returns EACCES as expected.
Also this issue not reproduces when we use SMB1 protocol (vers=1.0 in
mount options).
Further investigation showed that the mapping from status_to_posix_error
is different for SMB1 and SMB2+ implementations.
For SMB1 mapping is [NT_STATUS_LOCK_NOT_GRANTED to ERRlock]
(See fs/cifs/netmisc.c line 66)
but for SMB2+ mapping is [STATUS_LOCK_NOT_GRANTED to -EIO]
(see fs/cifs/smb2maperror.c line 383)
Quick changes in SMB2+ mapping from EIO to EACCES has fixed issue.
Signed-off-by: Georgy A Bystrenin <gkot@altlinux.org> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 885872b722b7 ("MIPS: Octeon: Add Octeon III CN7xxx
interface detection") added RGMII interface detection for OCTEON III,
but it results in the following logs:
[ 7.165984] ERROR: Unsupported Octeon model in __cvmx_helper_rgmii_probe
[ 7.173017] ERROR: Unsupported Octeon model in __cvmx_helper_rgmii_probe
The current RGMII routines are valid only for older OCTEONS that
use GMX/ASX hardware blocks. On later chips AGL should be used,
but support for that is missing in the mainline. Until that is added,
mark the interface as disabled.
Fixes: 885872b722b7 ("MIPS: Octeon: Add Octeon III CN7xxx interface detection") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@vger.kernel.org Cc: stable@vger.kernel.org # 4.7+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KEXEC needs the new kernel's load address to be aligned on a page
boundary (see sanity_check_segment_list()), but on MIPS the default
vmlinuz load address is only explicitly aligned to 16 bytes.
Since the largest PAGE_SIZE supported by MIPS kernels is 64KB, increase
the alignment calculated by calc_vmlinuz_load_addr to 64KB.
Treat "block_count" from struct f2fs_super_block as 64-bit little endian
value in sanity_check_raw_super() because struct f2fs_super_block
declares "block_count" as "__le64".
This fixes a bug where the superblock validation fails on big endian
devices with the following error:
F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
F2FS-fs (sda1): Can't find valid F2FS filesystem in 1th superblock
F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
F2FS-fs (sda1): Can't find valid F2FS filesystem in 2th superblock
As result of this the partition cannot be mounted.
With this patch applied the superblock validation works fine and the
partition can be mounted again:
F2FS-fs (sda1): Mounted with checkpoint version = 7c84
My little endian x86-64 hardware was able to mount the partition without
this fix.
To confirm that mounting f2fs filesystems works on big endian machines
again I tested this on a 32-bit MIPS big endian (lantiq) device.
Fixes: 0cfe75c5b01199 ("f2fs: enhance sanity_check_raw_super() to avoid potential overflows") Cc: stable@vger.kernel.org Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mediatek Preloader is a proprietary embedded boot loader for loading
Little Kernel and Linux into device DRAM.
This boot loader also handle firmware update. Mediatek Preloader will be
enumerated as a virtual COM port when the device is connected to Windows
or Linux OS via CDC-ACM class driver. When the USB enumeration has been
done, Mediatek Preloader will send out handshake command "READY" to PC
actively instead of waiting command from the download tool.
Since Linux 4.12, the commit "tty: reset termios state on device
registration" (93857edd9829e144acb6c7e72d593f6e01aead66) causes Mediatek
Preloader receiving some abnoraml command like "READYXX" as it sent.
This will be recognized as an incorrect response. The behavior change
also causes the download handshake fail. This change only affects
subsequent connects if the reconnected device happens to get the same minor
number.
By disabling the ECHO termios flag could avoid this problem. However, it
cannot be done by user space configuration when download tool open
/dev/ttyACM0. This is because the device running Mediatek Preloader will
send handshake command "READY" immediately once the CDC-ACM driver is
ready.
This patch wants to fix above problem by introducing "DISABLE_ECHO"
property in driver_info. When Mediatek Preloader is connected, the
CDC-ACM driver could disable ECHO flag in termios to avoid the problem.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> Cc: stable@vger.kernel.org Reviewed-by: Johan Hovold <johan@kernel.org> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRQ handler bcm2835_spi_interrupt() first reads as much as possible
from the RX FIFO, then writes as much as possible to the TX FIFO.
Afterwards it decides whether the transfer is finished by checking if
the TX FIFO is empty.
If very few bytes were written to the TX FIFO, they may already have
been transmitted by the time the FIFO's emptiness is checked. As a
result, the transfer will be declared finished and the chip will be
reset without reading the corresponding received bytes from the RX FIFO.
The odds of this happening increase with a high clock frequency (such
that the TX FIFO drains quickly) and either passing "threadirqs" on the
command line or enabling CONFIG_PREEMPT_RT_BASE (such that the IRQ
handler may be preempted between filling the TX FIFO and checking its
emptiness).
Fix by instead checking whether rx_len has reached zero, which means
that the transfer has been received in full. This is also more
efficient as it avoids one bus read access per interrupt. Note that
bcm2835_spi_transfer_one_poll() likewise uses rx_len to determine
whether the transfer has finished.
Signed-off-by: Lukas Wunner <lukas@wunner.de> Fixes: e34ff011c70e ("spi: bcm2835: move to the transfer_one driver model") Cc: stable@vger.kernel.org # v4.1+ Cc: Mathias Duckeck <m.duckeck@kunbus.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Martin Sperl <kernel@martin.sperl.org> Cc: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If submission of a DMA TX transfer succeeds but submission of the
corresponding RX transfer does not, the BCM2835 SPI driver terminates
the TX transfer but neglects to reset the dma_pending flag to false.
Thus, if the next transfer uses interrupt mode (because it is shorter
than BCM2835_SPI_DMA_MIN_LENGTH) and runs into a timeout,
dmaengine_terminate_all() will be called both for TX (once more) and
for RX (which was never started in the first place). Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de> Fixes: 3ecd37edaa2a ("spi: bcm2835: enable dma modes for transfers meeting certain conditions") Cc: stable@vger.kernel.org # v4.2+ Cc: Mathias Duckeck <m.duckeck@kunbus.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Martin Sperl <kernel@martin.sperl.org> Cc: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a DMA transfer finishes orderly right when spi_transfer_one_message()
determines that it has timed out, the callbacks bcm2835_spi_dma_done()
and bcm2835_spi_handle_err() race to call dmaengine_terminate_all(),
potentially leading to double termination.
Prevent by atomically changing the dma_pending flag before calling
dmaengine_terminate_all().
Signed-off-by: Lukas Wunner <lukas@wunner.de> Fixes: 3ecd37edaa2a ("spi: bcm2835: enable dma modes for transfers meeting certain conditions") Cc: stable@vger.kernel.org # v4.2+ Cc: Mathias Duckeck <m.duckeck@kunbus.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Martin Sperl <kernel@martin.sperl.org> Cc: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some time back, nfsd switched from calling vfs_fsync() to using a new
commit_metadata() hook in export_operations(). If the file system did
not provide a commit_metadata() hook, it fell back to using
sync_inode_metadata(). Unfortunately doesn't work on all file
systems. In particular, it doesn't work on ext4 due to how the inode
gets journalled --- the VFS writeback code will not always call
ext4_write_inode().
So we need to provide our own ext4_nfs_commit_metdata() method which
calls ext4_write_inode() directly.
In ext4_expand_extra_isize_ea(), we calculate the total size of the
xattr header, plus the xattr entries so we know how much of the
beginning part of the xattrs to move when expanding the inode extra
size. We need to include the terminating u32 at the end of the xattr
entries, or else if there is uninitialized, non-zero bytes after the
xattr entries and before the xattr values, the list of xattr entries
won't be properly terminated.
Reported-by: Steve Graham <stgraham2000@gmail.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e2b911c53584 ("ext4: clean up feature test macros with
predicate functions") broke the EXT4_IOC_GROUP_ADD ioctl. This was
not noticed since only very old versions of resize2fs (before
e2fsprogs 1.42) use this ioctl. However, using a new kernel with an
enterprise Linux userspace will cause attempts to use online resize to
fail with "No reserved GDT blocks".
Fixes: e2b911c53584 ("ext4: clean up feature test macros with predicate...") Cc: stable@kernel.org # v4.4 Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: ruippan (潘睿) <ruippan@tencent.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function frees qf_inode via iput but then pass qf_inode to
lockdep_set_quota_inode on the failure path. This may result in a
use-after-free bug. The patch frees df_inode only when it is never used.
Fixes: daf647d2dd5 ("ext4: add lockdep annotations for i_data_sem") Cc: stable@kernel.org # 4.6 Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on which functions are inlined in util/pmu.c, the snprintf()
calls in perf_pmu__parse_{scale,unit,per_pkg,snapshot}() might trigger a
warning:
util/pmu.c: In function 'pmu_aliases':
util/pmu.c:178:31: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size between 0 and 4095 [-Werror=format-truncation=]
snprintf(path, PATH_MAX, "%s/%s.unit", dir, name);
^~
I found this when trying to build perf from Linux 3.16 with gcc 8.
However I can reproduce the problem in mainline if I force
__perf_pmu__new_alias() to be inlined.
Suppress this by using scnprintf() as has been done elsewhere in perf.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20181111184524.fux4taownc6ndbx6@decadent.org.uk Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seen from the outside, the logic is pretty close with the former
helpers and people used it with the same logic as before: a
platform_msi_domain_alloc() call should be balanced with a
platform_msi_domain_free() call. While this is probably what was
intended to do, the platform_msi_domain_free() does not remove/free
the IRQ descriptor(s) created/inserted in
platform_msi_domain_alloc().
One effect of such situation is that removing a module that requested
an IRQ will let one orphaned IRQ descriptor (with an allocated MSI
entry) in the device descriptors list. Next time the module will be
inserted back, one will observe that the allocation will happen twice
in the MSI domain, one time for the remaining descriptor, one time for
the new one. It also has the side effect to quickly overshoot the
maximum number of allocated MSI and then prevent any module requesting
an interrupt in the same domain to be inserted anymore.
This situation has been met with loops of insertion/removal of the
mvpp2.ko module (requesting 15 MSIs each time).
Fixes: 552c494a7666 ("platform-msi: Allow creation of a MSI-based stacked irq domain") Cc: stable@vger.kernel.org Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
____kvm_handle_fault_on_reboot() provides a generic exception fixup
handler that is used to cleanly handle faults on VMX/SVM instructions
during reboot (or at least try to). If there isn't a reboot in
progress, ____kvm_handle_fault_on_reboot() treats any exception as
fatal to KVM and invokes kvm_spurious_fault(), which in turn generates
a BUG() to get a stack trace and die.
When it was originally added by commit 4ecac3fd6dc2 ("KVM: Handle
virtualization instruction #UD faults during reboot"), the "call" to
kvm_spurious_fault() was handcoded as PUSH+JMP, where the PUSH'd value
is the RIP of the faulting instructing.
The PUSH+JMP trickery is necessary because the exception fixup handler
code lies outside of its associated function, e.g. right after the
function. An actual CALL from the .fixup code would show a slightly
bogus stack trace, e.g. an extra "random" function would be inserted
into the trace, as the return RIP on the stack would point to no known
function (and the unwinder will likely try to guess who owns the RIP).
Unfortunately, the JMP was replaced with a CALL when the macro was
reworked to not spin indefinitely during reboot (commit b7c4145ba2eb
"KVM: Don't spin on virt instruction faults during reboot"). This
causes the aforementioned behavior where a bogus function is inserted
into the stack trace, e.g. my builds like to blame free_kvm_area().
Revert the CALL back to a JMP. The changelog for commit b7c4145ba2eb
("KVM: Don't spin on virt instruction faults during reboot") contains
nothing that indicates the switch to CALL was deliberate. This is
backed up by the fact that the PUSH <insn RIP> was left intact.
Note that an alternative to the PUSH+JMP magic would be to JMP back
to the "real" code and CALL from there, but that would require adding
a JMP in the non-faulting path to avoid calling kvm_spurious_fault()
and would add no value, i.e. the stack trace would be the same.
SIMCOM are reusing a single device ID for many (all of their?)
different modems, based on different chipsets and firmwares. Newer
Qualcomm chipset generations require setting DTR to wake the QMI
function. The SIM7600E modem is using such a chipset, making it
fail to work with this driver despite the device ID match.
Fix by unconditionally enabling the SET_DTR quirk for all SIMCOM
modems using this specific device ID. This is similar to what
we already have done for another case of device IDs recycled over
multiple chipset generations: 14cf4a771b30 ("drivers: net: usb:
qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201")
Initial testing on an older SIM7100 modem shows no immediate side
effects.
Reported-by: Sebastian Sjoholm <sebastian.sjoholm@gmail.com> Cc: Reinhard Speyerer <rspmn@arcor.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the cmd.read_write setting is not initialized so it contains
garbage from the stack. Fix this by setting it to 0 to indicate a
read is required.
Detected by CoverityScan, CID#1357925 ("Uninitialized scalar variable")
Fixes: c5c77ba18ea6 ("staging: wilc1000: Add SDIO/SPI 802.11 driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Cc: stable <stable@vger.kernel.org> Acked-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may
be concurrently executed.
The two functions both access a possible shared variable "hep->hcpriv".
This shared variable is freed by r8a66597_endpoint_disable() via the
call path:
r8a66597_endpoint_disable
kfree(hep->hcpriv) (line 1995 in Linux-4.19)
This variable is read by r8a66597_urb_enqueue() via the call path:
r8a66597_urb_enqueue
spin_lock_irqsave(&r8a66597->lock)
init_pipe_info
enable_r8a66597_pipe
pipe = hep->hcpriv (line 802 in Linux-4.19)
The read operation is protected by a spinlock, but the free operation
is not protected by this spinlock, thus a concurrency use-after-free bug
may occur.
To fix this bug, the spin-lock and spin-unlock function calls in
r8a66597_endpoint_disable() are moved to protect the free operation.
Added USB serial option driver support for Fibocom NL678 series cellular
module: VID 2cb7 and PIDs 0x0104 and 0x0105.
Reserved network and ADB interfaces.
Even after disabling interrupts on the module, it could be possible
that irq handlers are still running. System hang is seen during
suspend path. It was found that, there were pending writes on the
HDA bus and clock was disabled by that time.
Above mentioned issue is fixed by clearing any pending irq handlers
before disabling clocks and returning from hda suspend.
I ran into a link-time error with the atmel-quadspi driver on the
EBSA110 platform:
drivers/mtd/built-in.o: In function `atmel_qspi_run_command':
:(.text+0x1ee3c): undefined reference to `_memcpy_toio'
:(.text+0x1ee48): undefined reference to `_memcpy_fromio'
The problem is that _memcpy_toio/_memcpy_fromio are not available on
that platform, and we have to prevent building the driver there.
In case we want to backport this to older kernels: between linux-4.8
and linux-4.20, the Kconfig entry was in drivers/mtd/spi-nor/Kconfig
but had the same problem.
Link: https://lore.kernel.org/patchwork/patch/812860/ Fixes: 161aaab8a067 ("mtd: atmel-quadspi: add driver for Atmel QSPI controller") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this by sanitizing both info.mode and info.port before using them
to index emu->portptrs[i]->ctrls, emu->portptrs[info.port]->ctrls and
emu->portptrs.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Fix this by sanitizing stream before using it to index pcm->streams
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Fix this by sanitizing ipcm->substream before using it to index emu->fx8010.pcm
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Fix this by sanitizing info->channel before using it to index hdsp->channel_map
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Also, notice that I refactored the code a bit in order to get rid of the
following checkpatch warning:
ERROR: do not use assignment in if condition
FILE: sound/pci/rme9652/hdsp.c:4103:
if ((mapped_channel = hdsp->channel_map[info->channel]) < 0)
__ptr_ring_swap_queue() tries to move pointers from the old
ring to the new one, but it forgets to check if ->producer
is beyond the new size at the end of the operation. This leads
to an out-of-bound access in __ptr_ring_produce() as reported
by syzbot.
Reported-by: syzbot+8993c0fa96d57c399735@syzkaller.appspotmail.com Fixes: 5d49de532002 ("ptr_ring: resize support") Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: Jason Wang <jasowang@redhat.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro mentioned (Message-ID
<20170626041334.GZ10672@ZenIV.linux.org.uk>)
that there is probably a race condition
lurking in accesses of sk_stamp on 32-bit machines.
sock->sk_stamp is of type ktime_t which is always an s64.
On a 32 bit architecture, we might run into situations of
unsafe access as the access to the field becomes non atomic.
Use seqlocks for synchronization.
This allows us to avoid using spinlocks for readers as
readers do not need mutual exclusion.
Another approach to solve this is to require sk_lock for all
modifications of the timestamps. The current approach allows
for timestamps to have their own lock: sk_stamp_lock.
This allows for the patch to not compete with already
existing critical sections, and side effects are limited
to the paths in the patch.
The addition of the new field maintains the data locality
optimizations from
commit 9115e8cd2a0c ("net: reorganize struct sock for better data
locality")
Note that all the instances of the sk_stamp accesses
are either through the ioctl or the syscall recvmsg.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add napi_disable routine in gro_cells_destroy since starting from
commit c42858eaf492 ("gro_cells: remove spinlock protecting receive
queues") gro_cell_poll and gro_cells_destroy can run concurrently on
napi_skbs list producing a kernel Oops if the tunnel interface is
removed while gro_cell_poll is running. The following Oops has been
triggered removing a vxlan device while the interface is receiving
traffic
Fixes: c42858eaf492 ("gro_cells: remove spinlock protecting receive queues") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When TIPC_NLA_UDP_REMOTE is an IPv6 mcast address but
TIPC_NLA_UDP_LOCAL is an IPv4 address, a NULL-ptr deref is triggered
as the UDP tunnel sock is initialized to IPv4 or IPv6 sock merely
based on the protocol in local address.
We should just error out when the remote address and local address
have different protocols.
Reported-by: syzbot+eb4da3a20fad2e52555d@syzkaller.appspotmail.com Cc: Ying Xue <ying.xue@windriver.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lock_sock() must be used in process context to be race-free with
other lock_sock() callers, for example, tipc_release(). Otherwise
using the spinlock directly can't serialize a parallel tipc_release().
As it is blocking, we have to hold the sock refcnt before
rhashtable_walk_stop() and release it after rhashtable_walk_start().
Fixes: 07f6c4bc048a ("tipc: convert tipc reference table to use generic rhashtable") Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Ying Xue <ying.xue@windriver.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least old Xen net backends seem to send frags with no real data
sometimes. In case such a fragment happens to occur with the frag limit
already reached the frontend will BUG currently even if this situation
is easily recoverable.
Modify the BUG_ON() condition accordingly.
Tested-by: Dietmar Hahn <dietmar.hahn@ts.fujitsu.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a server side socket is bound to an address, but not in the listening
state yet, incoming connection requests should receive a reset control
packet in response. However, the function used to send the reset
silently drops the reset packet if the sending socket isn't bound
to a remote address (as is the case for a bound socket not yet in
the listening state). This change fixes this by using the src
of the incoming packet as destination for the reset packet in
this case.
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets") Reviewed-by: Adit Ranadive <aditr@vmware.com> Reviewed-by: Vishnu Dasa <vdasa@vmware.com> Signed-off-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We miss a write barrier that guarantees used idx is updated and seen
before log. This will let userspace sync and copy used ring before
used idx is update. Fix this by adding a barrier before log_write().
Fixes: 8dd014adfea6f ("vhost-net: mergeable buffers support") Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported a kernel-infoleak, which is caused by an uninitialized
field(sin6_flowinfo) of addr->a.v6 in sctp_inet6addr_event().
The call trace is as below:
sin6_flowinfo is not really used by SCTP, so it will be fixed by simply
setting it to 0.
The issue exists since very beginning.
Thanks Alexander for the reproducer provided.
Reported-by: syzbot+ad5d327e6936a2e284be@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Validate packet socket address length if a length is given. Zero
length is equivalent to not setting an address.
Fixes: 99137b7888f4 ("packet: validate address length") Reported-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Packet sockets with SOCK_DGRAM may pass an address for use in
dev_hard_header. Ensure that it is of sufficient length.
Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When x25_asy_open() fails, it already cleans up by itself,
so its caller doesn't need to free the memory again.
It seems we still have to call x25_asy_free() to clear the SLF_INUSE
bit, so just set these pointers to NULL after kfree().
Reported-and-tested-by: syzbot+5e5e969e525129229052@syzkaller.appspotmail.com Fixes: 3b780bed3138 ("x25_asy: Free x25_asy on x25_asy_open() failure.") Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nr_find_socket(), nr_find_peer() and nr_find_listener() lock the
sock after finding it in the global list. However, the call path
requires BH disabled for the sock lock consistently.
Actually the locking is unnecessary at this point, we can just hold
the sock refcnt to make sure it is not gone after we unlock the global
list, and lock it later only when needed.
Reported-and-tested-by: syzbot+f621cda8b7e598908efa@syzkaller.appspotmail.com Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff59d ("phy: Move PHY PM operations into phy_device") Suggested-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 7969e5c40dfd ("ip: discard IPv4 datagrams with overlapping
segments.") IPv4 reassembly code drops the whole queue whenever an
overlapping fragment is received. However, the test is written in a way
which detects duplicate fragments as overlapping so that in environments
with many duplicate packets, fragmented packets may be undeliverable.
Add an extra test and for (potentially) duplicate fragment, only drop the
new fragment rather than the whole queue. Only starting offset and length
are checked, not the contents of the fragments as that would be too
expensive. For similar reason, linear list ("run") of a rbtree node is not
iterated, we only check if the new fragment is a subset of the interval
covered by existing consecutive fragments.
v2: instead of an exact check iterating through linear list of an rbtree
node, only check if the new fragment is subset of the "run" (suggested
by Eric Dumazet)
Fixes: 7969e5c40dfd ("ip: discard IPv4 datagrams with overlapping segments.") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Local variable description: ----data.i@capi_unlocked_ioctl
Variable was created at:
capi_ioctl drivers/isdn/capi/capi.c:747 [inline]
capi_unlocked_ioctl+0x82/0x1bf0 drivers/isdn/capi/capi.c:939
do_vfs_ioctl+0xebd/0x2bf0 fs/ioctl.c:46
Bytes 12-63 of 64 are uninitialized
Memory access of size 64 starts at ffff88807ac5fce8
Data copied to user address 0000000020000080
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xfrm6_policy_check() might have re-allocated skb->head, we need
to reload ipv6 header pointer.
sysbot reported :
BUG: KASAN: use-after-free in __ipv6_addr_type+0x302/0x32f net/ipv6/addrconf_core.c:40
Read of size 4 at addr ffff888191b8cb70 by task syz-executor2/1304
Memory state around the buggy address: ffff888191b8ca00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888191b8ca80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
>ffff888191b8cb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff888191b8cb80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888191b8cc00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 0d3c703a9d17 ("ipv6: Cleanup IPv6 tunnel receive path") Fixes: ed1efb2aefbb ("ipv6: Add support for IPsec virtual tunnel interfaces") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported the use of uninitialized udp6_addr::sin6_scope_id.
We can just set ::sin6_scope_id to zero, as tunnels are unlikely
to use an IPv6 address that needs a scope id and there is no
interface to bind in this context.
For net-next, it looks different as we have cfg->bind_ifindex there
so we can probably call ipv6_iface_scope_id().
Same for ::sin6_flowinfo, tunnels don't use it.
Fixes: 8024e02879dd ("udp: Add udp_sock_create for UDP tunnels to open listener socket") Reported-by: syzbot+c56449ed3652e6720f30@syzkaller.appspotmail.com Cc: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Packet sockets may call dev_header_parse with NULL daddr. Make
lowpan_header_ops.create fail.
Fixes: 87a93e4eceb4 ("ieee802154: change needed headroom/tailroom") Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Alexander Aring <aring@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 33a48ab105a7 ("ibmveth: Fix DMA unmap error") fixed an issue in the
normal code path of ibmveth_xmit_start() that was originally introduced by
Commit 6e8ab30ec677 ("ibmveth: Add scatter-gather support"). This original
fix missed the error path where dma_unmap_page is wrongly called on the
header portion in descs[0] which was mapped with dma_map_single. As a
result a failure to DMA map any of the frags results in a dmesg warning
when CONFIG_DMA_API_DEBUG is enabled.
------------[ cut here ]------------
DMA-API: ibmveth 30000002: device driver frees DMA memory with wrong function
[device address=0x000000000a430000] [size=172 bytes] [mapped as page] [unmapped as single]
WARNING: CPU: 1 PID: 8426 at kernel/dma/debug.c:1085 check_unmap+0x4fc/0xe10
...
<snip>
...
DMA-API: Mapped at:
ibmveth_start_xmit+0x30c/0xb60
dev_hard_start_xmit+0x100/0x450
sch_direct_xmit+0x224/0x490
__qdisc_run+0x20c/0x980
__dev_queue_xmit+0x1bc/0xf20
This fixes the API misuse by unampping descs[0] with dma_unmap_single.
Fixes: 6e8ab30ec677 ("ibmveth: Add scatter-gather support") Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. After freeing dev->ax25_ptr, we need to set it to NULL otherwise
we may use a dangling pointer.
2. There is a race between ax25_setsockopt() and device notifier as
reported by syzbot. Close it by holding RTNL lock.
3. We need to test if dev->ax25_ptr is NULL before using it.
Reported-and-tested-by: syzbot+ae6bb869cbed29b29040@syzkaller.appspotmail.com Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this by sanitizing vr.vifi before using it to index mrt->vif_table'
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this by sanitizing vr.mifi before using it to index mrt->vif_table'
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Directly including access_ok.h can result in the following compile errors
if an architecture such as ia64 does not support direct unaligned accesses.
include/linux/unaligned/access_ok.h:7:19: error:
redefinition of 'get_unaligned_le16'
include/linux/unaligned/le_struct.h:6:19: note:
previous definition of 'get_unaligned_le16' was here
include/linux/unaligned/access_ok.h:12:19: error:
redefinition of 'get_unaligned_le32'
include/linux/unaligned/le_struct.h:11:19: note:
previous definition of 'get_unaligned_le32' was here
Include asm/unaligned.h instead and let the architecture decide which
access functions to use.
Fix this by sanitizing nr before using it to index dev->driver->ioctls
and drm_ioctls.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
proc_sys_lookup can fail with ENOMEM instead of ENOENT when the
corresponding sysctl table is being unregistered. In our case we see
this upon opening /proc/sys/net/*/conf files while network interfaces
are being deleted, which confuses our configuration daemon.
The problem was successfully reproduced and this fix tested on v4.9.122
and v4.20-rc6.
v2: return ERR_PTRs in all cases when proc_sys_make_inode fails instead
of mixing them with NULL. Thanks Al Viro for the feedback.
Fixes: ace0c791e6c3 ("proc/sysctl: Don't grab i_lock under sysctl_lock.") Cc: stable@vger.kernel.org Signed-off-by: Ivan Delalande <colona@arista.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From printk()/serial console point of view panic() is special, because
it may force CPU to re-enter printk() or/and serial console driver.
Therefore, some of serial consoles drivers are re-entrant. E.g. 8250:
serial8250_console_write()
{
if (port->sysrq)
locked = 0;
else if (oops_in_progress)
locked = spin_trylock_irqsave(&port->lock, flags);
else
spin_lock_irqsave(&port->lock, flags);
...
}
panic() does set oops_in_progress via bust_spinlocks(1), so in theory
we should be able to re-enter serial console driver from panic():
However, this does not happen and we deadlock in serial console on
port->lock spinlock. And the problem is that console_flush_on_panic()
called after bust_spinlocks(0):
bust_spinlocks(0) decrements oops_in_progress, so oops_in_progress
can go back to zero. Thus even re-entrant console drivers will simply
spin on port->lock spinlock. Given that port->lock may already be
locked either by a stopped CPU, or by the very same CPU we execute
panic() on (for instance, NMI panic() on printing CPU) the system
deadlocks and does not reboot.
Fix this by removing bust_spinlocks(0), so oops_in_progress is always
set in panic() now and, thus, re-entrant console drivers will trylock
the port->lock instead of spinning on it forever, when we call them
from console_flush_on_panic().
Link: http://lkml.kernel.org/r/20181025101036.6823-1-sergey.senozhatsky@gmail.com Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Daniel Wang <wonderfly@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Cc: Jiri Slaby <jslaby@suse.com> Cc: Peter Feiner <pfeiner@google.com> Cc: linux-serial@vger.kernel.org Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
