When 'ping' changes to use PING socket instead of RAW socket by:
# sysctl -w net.ipv4.ping_group_range="0 100"
the selftests 'router_broadcast.sh' will fail, as such command
# ip vrf exec vrf-h1 ping -I veth0 198.51.100.255 -b
can't receive the response skb by the PING socket. It's caused by mismatch
of sk_bound_dev_if and dif in ping_rcv() when looking up the PING socket,
as dif is vrf-h1 if dif's master was set to vrf-h1.
This patch is to fix this regression by also checking the sk_bound_dev_if
against sdif so that the packets can stil be received even if the socket
is not bound to the vrf device but to the real iif.
Fixes: c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind") Reported-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Experiments with MAX6680 and MAX6681 show that the alert function of those
chips is broken, similar to other chips supported by the lm90 driver.
Mark it accordingly.
Experiments with MAX6646 and MAX6648 show that the alert function of those
chips is broken, similar to other chips supported by the lm90 driver.
Mark it accordingly.
In one net namespace, after creating a packet socket without binding
it to a device, users in other net namespaces can observe the new
`packet_type` added by this packet socket by reading `/proc/net/ptype`
file. This is minor information leakage as packet socket is
namespace aware.
Add a net pointer in `packet_type` to keep the net namespace of
of corresponding packet socket. In `ptype_seq_show`, this net pointer
must be checked when it is not NULL.
Fixes: 2feb27dbe00c ("[NETNS]: Minor information leak via /proc/net/ptype file.") Signed-off-by: Congyu Liu <liu3101@purdue.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The bnx2fc_destroy() functions are removing the interface before calling
destroy_work. This results multiple WARNings from sysfs_remove_group() as
the controller rport device attributes are removed too early.
Replace the fcoe_port's destroy_work queue. It's not needed.
The problem is easily reproducible with the following steps.
struct rpmsg_eptdev contains a struct cdev. The current code frees
the rpmsg_eptdev struct in rpmsg_eptdev_destroy(), but the cdev is
a managed object, therefore its release is not predictable and the
rpmsg_eptdev could be freed before the cdev is entirely released.
The cdev_device_add/del() API was created to address this issue
(see commit '233ed09d7fda ("chardev: add helper function to register
char devs with a struct device")'), use it instead of cdev add/del().
Fixes: c0cdc19f84a4 ("rpmsg: Driver for user space endpoint interface") Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220110104706.v6.2.Idde68b05b88d4a2e6e54766c653f3a6d9e419ce6@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct rpmsg_ctrldev contains a struct cdev. The current code frees
the rpmsg_ctrldev struct in rpmsg_ctrldev_release_device(), but the
cdev is a managed object, therefore its release is not predictable
and the rpmsg_ctrldev could be freed before the cdev is entirely
released, as in the backtrace below.
The cdev_device_add/del() API was created to address this issue (see
commit '233ed09d7fda ("chardev: add helper function to register char
devs with a struct device")'), use it instead of cdev add/del().
Fixes: c0cdc19f84a4 ("rpmsg: Driver for user space endpoint interface") Signed-off-by: Sujit Kautkar <sujitka@chromium.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220110104706.v6.1.Iaac908f3e3149a89190ce006ba166e2d3fd247a3@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix for failed to init adminq: -53 while VF is resetting via MAC
address changing procedure.
Added sync module to avoid reading deadbeef value in reinit adminq
during software reset.
Without this patch it is possible to trigger VF reset procedure
during reinit adminq. This resulted in an incorrect reading of
value from the AQP registers and generated the -53 error.
Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface") Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Signed-off-by: Karen Sornek <karen.sornek@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was caused by PF queue pile fragmentation due to
flow director VSI queue being placed right after main VSI.
Because of this main VSI was not able to resize its
queue allocation for XDP resulting in no queues allocated
for main VSI when XDP was turned on.
Fix this by always allocating last queue in PF queue pile
for a flow director VSI.
Fixes: 41c445ff0f48 ("i40e: main driver core") Fixes: 74608d17fe29 ("i40e: add support for XDP_TX action") Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this patch VF interface vanished when
maximum queue number was exceeded. Driver tried
to add next queues even if there was not enough
space. PF sent incorrect number of queues to
the VF when there were not enough of them.
Add an additional condition introduced to check
available space in 'qp_pile' before proceeding.
This condition makes it impossible to add queues
if they number is greater than the number resulting
from available space.
Also add the search for free space in PF queue
pair piles.
Without this patch VF interfaces are not seen
when available space for queues has been
exceeded and following logs appears permanently
in dmesg:
"Unable to get VF config (-32)".
"VF 62 failed opcode 3, retval: -5"
"Unable to get VF config due to PF error condition, not retrying"
Fixes: 7daa6bf3294e ("i40e: driver core headers") Fixes: 41c445ff0f48 ("i40e: main driver core") Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com> Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently simplified i40e_rebuild causes that FW sometimes
is not ready after NVM update, the ping does not return.
Increase the delay in case of EMP reset.
Old delay of 300 ms was introduced for specific cards for 710 series.
Now it works for all the cards and delay was increased.
Fixes: 1fa51a650e1d ("i40e: Add delay after EMP reset for firmware to recover") Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been reported some configuration where the kernel doesn't
boot with KASAN enabled.
This is due to wrong BAT allocation for the KASAN area:
---[ Data Block Address Translation ]---
0: 0xc0000000-0xcfffffff 0x00000000 256M Kernel rw m
1: 0xd0000000-0xdfffffff 0x10000000 256M Kernel rw m
2: 0xe0000000-0xefffffff 0x20000000 256M Kernel rw m
3: 0xf8000000-0xf9ffffff 0x2a000000 32M Kernel rw m
4: 0xfa000000-0xfdffffff 0x2c000000 64M Kernel rw m
A BAT must have both virtual and physical addresses alignment matching
the size of the BAT. This is not the case for BAT 4 above.
Fix kasan_init_region() by using block_size() function that is in
book3s32/mmu.c. To be able to reuse it here, make it non static and
change its name to bat_block_size() in order to avoid name conflict
with block_size() defined in <linux/blkdev.h>
Also reuse find_free_bat() to avoid an error message from setbat()
when no BAT is available.
And allocate memory outside of linear memory mapping to avoid
wasting that precious space.
With this change we get correct alignment for BATs and KASAN shadow
memory is allocated outside the linear memory space.
---[ Instruction Block Address Translation ]---
0: 0xc0000000-0xc03fffff 0x00000000 4M Kernel x m
1: 0xc0400000-0xc05fffff 0x00400000 2M Kernel x m
2: 0xc0600000-0xc06fffff 0x00600000 1M Kernel x m
3: 0xc0700000-0xc077ffff 0x00700000 512K Kernel x m
4: 0xc0780000-0xc079ffff 0x00780000 128K Kernel x m
5: 0xc07a0000-0xc07bffff 0x007a0000 128K Kernel x m
6: -
7: -
The two 128K should be a single 256K instead.
When _etext is not aligned to 128Kbytes, the system will allocate
all necessary BATs to the lower 128Kbytes boundary, then allocate
an additional 128Kbytes BAT for the remaining block.
Instead, align the top to 128Kbytes so that the function directly
allocates a 256Kbytes last block:
---[ Instruction Block Address Translation ]---
0: 0xc0000000-0xc03fffff 0x00000000 4M Kernel x m
1: 0xc0400000-0xc05fffff 0x00400000 2M Kernel x m
2: 0xc0600000-0xc06fffff 0x00600000 1M Kernel x m
3: 0xc0700000-0xc077ffff 0x00700000 512K Kernel x m
4: 0xc0780000-0xc07bffff 0x00780000 256K Kernel x m
5: -
6: -
7: -
Changes to the AMD Thresholding sysfs code prevents sysfs writes from
updating the underlying registers once CPU init is completed, i.e.
"threshold_banks" is set.
Allow the registers to be updated if the thresholding interface is
already initialized or if in the init path. Use the "set_lvt_off" value
to indicate if running in the init path, since this value is only set
during init.
The membarrier command MEMBARRIER_CMD_QUERY allows querying the
available membarrier commands. When the membarrier-rseq fence commands
were added, a new MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ_BITMASK was
introduced with the intent to expose them with the MEMBARRIER_CMD_QUERY
command, the but it was never added to MEMBARRIER_CMD_BITMASK.
The membarrier-rseq fence commands are therefore not wired up with the
query command.
Rename MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ_BITMASK to
MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK (the bitmask is not a command
per-se), and change the erroneous
MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_RSEQ_BITMASK (which does not
actually exist) to MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_RSEQ.
Wire up MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK in
MEMBARRIER_CMD_BITMASK. Fixing this allows discovering availability of
the membarrier-rseq fence feature.
This fixes a deadlock case in ocfs2. We firstly export jbd2 symbols
jbd2_journal_[grab|put]_journal_head as preparation and later use them
in ocfs2 insread of jbd_[lock|unlock]_bh_journal_head to fix the
deadlock.
This patch (of 2):
This exports symbols jbd2_journal_[grab|put]_journal_head, which will be
used outside modules, e.g. ocfs2.
Link: https://lkml.kernel.org/r/20220121071205.100648-2-joseph.qi@linux.alibaba.com Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: Andreas Dilger <adilger.kernel@dilger.ca> Cc: Gautham Ananthakrishna <gautham.ananthakrishna@oracle.com> Cc: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com> Cc: "Theodore Ts'o" <tytso@mit.edu> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CCGx clears Bit 0:Device Interrupt in the INTR_REG
if CCGx is reset successfully. However, there might
be a chance that other bits in INTR_REG are not
cleared due to internal data queued in PPM. This case
misleads the driver that CCGx reset failed.
The commit checks bit 0 in INTR_REG and ignores other
bits. The ucsi driver would reset PPM later.
Fixes: 247c554a14aa ("usb: typec: ucsi: add support for Cypress CCGx") Cc: stable@vger.kernel.org Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Sing-Han Chen <singhanc@nvidia.com> Signed-off-by: Wayne Chang <waynec@nvidia.com> Link: https://lore.kernel.org/r/20220112094143.628610-1-waynec@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V before tcpm gets to read port->tcpc->get_vbus. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return. It turns out the issue is not unlinking
the URB; that works just fine. Rather, the problem arises when the
wakeup notification that the URB has completed is not received.
The reason is memory-access ordering on SMP systems. In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:
CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
... ...
atomic_inc(&urb->reject); atomic_dec(&urb->use_count);
... ...
wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);
Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:
write urb->reject, then read urb->use_count;
whereas the overall pattern of accesses on CPU 1 is:
write urb->use_count, then read urb->reject.
This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes. The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject. Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().
The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().
The problem is fixed by adding suitable memory barriers. To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs. The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.
Currently when gadget enumerates in super speed plus, the isoc
endpoint request buffer size is not calculated correctly. Fix
this by checking the gadget speed against USB_SPEED_SUPER_PLUS
and update the request buffer size.
Commit 7495af930835 ("ARM: multi_v7_defconfig: Enable drivers for
DragonBoard 410c") enables the CONFIG_PHY_QCOM_USB_HS for the ARM
multi_v7_defconfig. Enabling this Kconfig is causing the kernel to crash
on the Tegra20 Ventana platform in the ulpi_match() function.
The Qualcomm USB HS PHY driver that is enabled by CONFIG_PHY_QCOM_USB_HS,
registers a ulpi_driver but this driver does not provide an 'id_table',
so when ulpi_match() is called on the Tegra20 Ventana platform, it
crashes when attempting to deference the id_table pointer which is not
valid. The Qualcomm USB HS PHY driver uses device-tree for matching the
ULPI driver with the device and so fix this crash by using device-tree
for matching if the id_table is not valid.
Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT") Cc: stable <stable@vger.kernel.org> Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20220117150039.44058-1-jonathanh@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The basic flow:
1. run time suspend call xhci_suspend, xhci parent devices gate the clock.
2. echo mem >/sys/power/state, system _device_suspend call xhci_suspend
3. xhci_suspend call xhci_disable_hub_port_wake, which access register,
but clock already gated by run time suspend.
This problem was hidden by power domain driver, which call run time resume before it.
But the below commit remove it and make this issue happen.
commit c1df456d0f06e ("PM: domains: Don't runtime resume devices at genpd_prepare()")
This patch call run time resume before suspend to make sure clock is on
before access register.
Reviewed-by: Peter Chen <peter.chen@kernel.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Frank Li <Frank.Li@nxp.com> Testeb-by: Abel Vesa <abel.vesa@nxp.com> Link: https://lore.kernel.org/r/20220110172738.31686-1-Frank.Li@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two people have reported (and mentioned numerous other reports on the
web) that VIA's VL817 USB-SATA bridge does not work with the uas
driver. Typical log messages are:
[ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD
[ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00
[ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd
[ 3606.328584] scsi host14: uas_eh_device_reset_handler success
Surprisingly, the devices do seem to work okay for some other people.
The cause of the differing behaviors is not known.
In the hope of getting the devices to work for the most users, even at
the possible cost of degraded performance for some, this patch adds an
unusual_devs entry for the VL817 to block it from binding to the uas
driver by default. Users will be able to override this entry by means
of a module parameter, if they want.
CC: <stable@vger.kernel.org> Reported-by: DocMAX <mail@vacharakis.de> Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for the some of the Brainboxes PCI range of
cards, including the UC-101, UC-235/246, UC-257, UC-268, UC-275/279,
UC-302, UC-310, UC-313, UC-320/324, UC-346, UC-357, UC-368
and UC-420/431.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF)
are the control characters defined in ISO/IEC 646. These shall be quoted if
seen in the data stream to avoid interpretation as flow control characters.
ISO/IEC 646 refers to the set of ISO standards described as the ISO
7-bit coded character set for information interchange. Its final version
is also known as ITU T.50.
See https://www.itu.int/rec/T-REC-T.50-199209-I/en
To abide the standard it is needed to quote DC1 and DC3 correctly if these
are seen as data bytes and not as control characters. The current
implementation already tries to enforce this but fails to catch all
defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most
significant bit shall be ignored for DC1 and DC3 handling. The current
implementation handles only the case with the most significant bit set 0.
Cases in which DC1 and DC3 have the most significant bit set 1 are left
unhandled.
This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only
the 7 least significant bits set 1) before comparing them with XON
(a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need
quotation via byte stuffing.
8250_of supports a reg-offset property which is intended to handle
cases where the device registers start at an offset inside the region
of memory allocated to the device. The Xilinx 16550 UART, for which this
support was initially added, requires this. However, the code did not
adjust the overall size of the mapped region accordingly, causing the
driver to request an area of memory past the end of the device's
allocation. For example, if the UART was allocated an address of
0xb0130000, size of 0x10000 and reg-offset of 0x1000 in the device
tree, the region of memory reserved was b0131000-b0140fff, which caused
the driver for the region starting at b0140000 to fail to probe.
Fix this by subtracting reg-offset from the mapped region size.
Fixes: b912b5e2cfb3 ([POWERPC] Xilinx: of_serial support for Xilinx uart 16550.) Cc: stable <stable@vger.kernel.org> Signed-off-by: Robert Hancock <robert.hancock@calian.com> Link: https://lore.kernel.org/r/20220112194214.881844-1-robert.hancock@calian.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The erratum 1418040 workaround enables CNTVCT_EL1 access trapping in EL0
when executing compat threads. The workaround is applied when switching
between tasks, but the need for the workaround could also change at an
exec(), when a non-compat task execs a compat binary or vice versa. Apply
the workaround in arch_setup_new_exec().
This leaves a small window of time between SET_PERSONALITY and
arch_setup_new_exec where preemption could occur and confuse the old
workaround logic that compares TIF_32BIT between prev and next. Instead, we
can just read cntkctl to make sure it's in the state that the next task
needs. I measured cntkctl read time to be about the same as a mov from a
general-purpose register on N1. Update the workaround logic to examine the
current value of cntkctl instead of the previous task's compat state.
Fixes: d49f7d7376d0 ("arm64: Move handling of erratum 1418040 into C code") Cc: <stable@vger.kernel.org> # 5.9.x Signed-off-by: D Scott Phillips <scott@os.amperecomputing.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20211220234114.3926-1-scott@os.amperecomputing.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do a runtime CPUID update for a vCPU if MSR_IA32_XSS is written, as the
size in bytes of the XSAVE area is affected by the states enabled in XSS.
Fixes: 203000993de5 ("kvm: vmx: add MSR logic for XSAVES") Cc: stable@vger.kernel.org Signed-off-by: Like Xu <likexu@tencent.com>
[sean: split out as a separate patch, adjust Fixes tag] Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220126172226.2298529-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While all userspace tried to limit commandstreams to 64K in size,
a bug in the Mesa driver lead to command streams of up to 128K
being submitted. Allow those to avoid breaking existing userspace.
Fixes: 6dfa2fab8ddd ("drm/etnaviv: limit submit sizes") Cc: stable@vger.kernel.org Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The user recently report a perf issue in the ICX platform, when test by
perf event “uncore_imc_x/cas_count_write”,the write bandwidth is always
very small (only 0.38MB/s), it is caused by the wrong "umask" for the
"cas_count_write" event. When double-checking, find "cas_count_read"
also is wrong.
The public document for ICX uncore:
3rd Gen Intel® Xeon® Processor Scalable Family, Codename Ice Lake,Uncore
Performance Monitoring Reference Manual, Revision 1.00, May 2021
On 2.4.7, it defines Unit Masks for CAS_COUNT:
RD b00001111
WR b00110000
So corrected both "cas_count_read" and "cas_count_write" for ICX.
Old settings:
hswep_uncore_imc_events
INTEL_UNCORE_EVENT_DESC(cas_count_read, "event=0x04,umask=0x03")
INTEL_UNCORE_EVENT_DESC(cas_count_write, "event=0x04,umask=0x0c")
New settings:
snr_uncore_imc_events
INTEL_UNCORE_EVENT_DESC(cas_count_read, "event=0x04,umask=0x0f")
INTEL_UNCORE_EVENT_DESC(cas_count_write, "event=0x04,umask=0x30")
Fixes: 2b3b76b5ec67 ("perf/x86/intel/uncore: Add Ice Lake server uncore support") Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Kan Liang <kan.liang@linux.intel.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20211223144826.841267-1-zhengjun.xing@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert a completely broken check on an "invalid" RIP in SVM's workaround
for the DecodeAssists SMAP errata. kvm_vcpu_gfn_to_memslot() obviously
expects a gfn, i.e. operates in the guest physical address space, whereas
RIP is a virtual (not even linear) address. The "fix" worked for the
problematic KVM selftest because the test identity mapped RIP.
Fully revert the hack instead of trying to translate RIP to a GPA, as the
non-SEV case is now handled earlier, and KVM cannot access guest page
tables to translate RIP.
Commit 49246466a989 ("fsnotify: move fsnotify_nameremove() hook out of
d_delete()") moved the fsnotify delete hook before d_delete() so fsnotify
will have access to a positive dentry.
This allowed a race where opening the deleted file via cached dentry
is now possible after receiving the IN_DELETE event.
To fix the regression in pseudo filesystems, convert d_delete() calls
to d_drop() (see commit 46c46f8df9aa ("devpts_pty_kill(): don't bother
with d_delete()") and move the fsnotify hook after d_drop().
Add a missing fsnotify_unlink() hook in nfsdfs that was found during
the audit of fsnotify hooks in pseudo filesystems.
Note that the fsnotify hooks in simple_recursive_removal() follow
d_invalidate(), so they require no change.
Dan reported that he was unable to write to files that had been
asynchronously created when the client's OSD caps are restricted to a
particular namespace.
The issue is that the layout for the new inode is only partially being
filled. Ensure that we populate the pool_ns_data and pool_ns_len in the
iinfo before calling ceph_fill_inode.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/54013 Fixes: 9a8d03ca2e2c ("ceph: attempt to do async create when possible") Reported-by: Dan van der Ster <dan@vanderster.com> Signed-off-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buffer handling in pm_show_wakelocks() is tricky, and hopefully
correct. Ensure it really is correct by using sysfs_emit_at() which
handles all of the tricky string handling logic in a PAGE_SIZE buffer
for us automatically as this is a sysfs file being read from.
Reviewed-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aditya reports [0] that his recent MacbookPro crashes in the firmware
when using the variable services at runtime. The culprit appears to be a
call to QueryVariableInfo(), which we did not use to call on Apple x86
machines in the past as they only upgraded from EFI v1.10 to EFI v2.40
firmware fairly recently, and QueryVariableInfo() (along with
UpdateCapsule() et al) was added in EFI v2.00.
The only runtime service introduced in EFI v2.00 that we actually use in
Linux is QueryVariableInfo(), as the capsule based ones are optional,
generally not used at runtime (all the LVFS/fwupd firmware update
infrastructure uses helper EFI programs that invoke capsule update at
boot time, not runtime), and not implemented by Apple machines in the
first place. QueryVariableInfo() is used to 'safely' set variables,
i.e., only when there is enough space. This prevents machines with buggy
firmwares from corrupting their NVRAMs when they run out of space.
Given that Apple machines have been using EFI v1.10 services only for
the longest time (the EFI v2.0 spec was released in 2006, and Linux
support for the newly introduced runtime services was added in 2011, but
the MacbookPro12,1 released in 2015 still claims to be EFI v1.10 only),
let's avoid the EFI v2.0 ones on all Apple x86 machines.
udf_expand_file_adinicb() calls directly ->writepage to write data
expanded into a page. This however misses to setup inode for writeback
properly and so we can crash on inode->i_wb dereference when submitting
page for IO like:
Fix the problem by marking the page dirty and going through the standard
writeback path to write the page. Strictly speaking we would not even
have to write the page but we want to catch e.g. ENOSPC errors early.
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com> CC: stable@vger.kernel.org Fixes: 52ebea749aae ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks") Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we fail to expand inode from inline format to a normal format, we
restore inode to contain the original inline formatting but we forgot to
set i_lenAlloc back. The mismatch between i_lenAlloc and i_size was then
causing further problems such as warnings and lost data down the line.
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com> CC: stable@vger.kernel.org Fixes: 7e49b6f2480c ("udf: Convert UDF to new truncate calling sequence") Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suppose we have an environment with a number of non-NPIV FCP devices
(virtual HBAs / FCP devices / zfcp "adapter"s) sharing the same physical
FCP channel (HBA port) and its I_T nexus. Plus a number of storage target
ports zoned to such shared channel. Now one target port logs out of the
fabric causing an RSCN. Zfcp reacts with an ADISC ELS and subsequent port
recovery depending on the ADISC result. This happens on all such FCP
devices (in different Linux images) concurrently as they all receive a copy
of this RSCN. In the following we look at one of those FCP devices.
Requests other than FSF_QTCB_FCP_CMND can be slow until they get a
response.
Depending on which requests are affected by slow responses, there are
different recovery outcomes. Here we want to fix failed recoveries on port
or adapter level by avoiding recovery requests that can be slow.
We need the cached N_Port_ID for the remote port "link" test with ADISC.
Just before sending the ADISC, we now intentionally forget the old cached
N_Port_ID. The idea is that on receiving an RSCN for a port, we have to
assume that any cached information about this port is stale. This forces a
fresh new GID_PN [FC-GS] nameserver lookup on any subsequent recovery for
the same port. Since we typically can still communicate with the nameserver
efficiently, we now reach steady state quicker: Either the nameserver still
does not know about the port so we stop recovery, or the nameserver already
knows the port potentially with a new N_Port_ID and we can successfully and
quickly perform open port recovery. For the one case, where ADISC returns
successfully, we re-initialize port->d_id because that case does not
involve any port recovery.
This also solves a problem if the storage WWPN quickly logs into the fabric
again but with a different N_Port_ID. Such as on virtual WWPN takeover
during target NPIV failover.
[https://www.redbooks.ibm.com/abstracts/redp5477.html] In that case the
RSCN from the storage FDISC was ignored by zfcp and we could not
successfully recover the failover. On some later failback on the storage,
we could have been lucky if the virtual WWPN got the same old N_Port_ID
from the SAN switch as we still had cached. Then the related RSCN
triggered a successful port reopen recovery. However, there is no
guarantee to get the same N_Port_ID on NPIV FDISC.
Even though NPIV-enabled FCP devices are not affected by this problem, this
code change optimizes recovery time for gone remote ports as a side effect.
The timely drop of cached N_Port_IDs prevents unnecessary slow open port
attempts.
While the problem might have been in code before v2.6.32 commit 799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp") this fix
depends on the gid_pn_work introduced with that commit, so we mark it as
culprit to satisfy fix dependencies.
Note: Point-to-point remote port is already handled separately and gets its
N_Port_ID from the cached peer_d_id. So resetting port->d_id in general
does not affect PtP.
Link: https://lore.kernel.org/r/20220118165803.3667947-1-maier@linux.ibm.com Fixes: 799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp") Cc: <stable@vger.kernel.org> #2.6.32+ Suggested-by: Benjamin Block <bblock@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Steffen Maier <maier@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
task_pt_regs() can return NULL on powerpc for kernel threads. This is
then used in __bpf_get_stack() to check for user mode, resulting in a
kernel oops. Guard against this by checking return value of
task_pt_regs() before trying to obtain the call chain.
Currently if z/VM guest is allowed to retrieve hypervisor performance
data globally for all guests (privilege class B) the query is formed in a
way to include all guests but the group name is left empty. This leads to
that z/VM guests which have access control group set not being included
in the results (even local vm).
Change the query group identifier from empty to "any" to retrieve
information about all guests from any groups (or without a group set).
If the size of the PLT entries generated by apply_rela() exceeds
64KiB, the first ones can no longer reach __jump_r1 with brc. Fix by
using brcl. An alternative solution is to add a __jump_r1 copy after
every 64KiB, however, the space savings are quite small and do not
justify the additional complexity.
When resume from suspend, besides skipping PTP registration, it also
skipping PTP HW initialization. This could cause PTP clock not able to
operate properly when resume from suspend.
To fix this, only stmmac_ptp_register() is skipped when resume from
suspend.
Fixes: fe1319291150 ("stmmac: Don't init ptp again when resume from suspend/hibernation") Cc: <stable@vger.kernel.org> # 5.15.x Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices
and sfp cages") added code which finds SFP bus DT node even if the node
is disabled with status = "disabled". Because of this, when phylink is
created, it ends with non-null .sfp_bus member, even though the SFP
module is not probed (because the node is disabled).
We need to ignore disabled SFP bus node.
Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") Signed-off-by: Marek Behún <kabel@kernel.org> Cc: stable@vger.kernel.org # 2203cbf2c8b5 ("net: sfp: move fwnode parsing into sfp-bus layer") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for out-of-bound read was being performed at the end of while
num_reports loop, and would fill journal with false positives. Added
check to beginning of loop processing so that it doesn't get checked
after ptr has been advanced.
A failing usercopy of the fence_rep object will lead to a stale entry in
the file descriptor table as put_unused_fd() won't release it. This
enables userland to refer to a dangling 'file' object through that still
valid file descriptor, leading to all kinds of use-after-free
exploitation scenarios.
Fix this by deferring the call to fd_install() until after the usercopy
has succeeded.
A task can end up indefinitely sleeping in do_select() ->
poll_schedule_timeout() when the following race happens:
TASK1 (thread1) TASK2 TASK1 (thread2)
do_select()
setup poll_wqueues table
with 'fd'
write data to 'fd'
pollwake()
table->triggered = 1
closes 'fd' thread1 is
waiting for
poll_schedule_timeout()
- sees table->triggered
table->triggered = 0
return -EINTR
loop back in do_select()
But at this point when TASK1 loops back, the fdget() in the setup of
poll_wqueues fails. So now so we never find 'fd' is ready for reading
and sleep in poll_schedule_timeout() indefinitely.
Treat an fd that got closed as a fd on which some event happened. This
makes sure cannot block indefinitely in do_select().
Another option would be to return -EBADF in this case but that has a
potential of subtly breaking applications that excercise this behavior
and it happens to work for them. So returning fd as active seems like a
safer choice.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the TDP MMU is write-protection GFNs for page table protection (as
opposed to for dirty logging, or due to the HVA not being writable), it
checks if the SPTE is already write-protected and if so skips modifying
the SPTE and the TLB flush.
This behavior is incorrect because it fails to check if the SPTE
is write-protected for page table protection, i.e. fails to check
that MMU-writable is '0'. If the SPTE was write-protected for dirty
logging but not page table protection, the SPTE could locklessly be made
writable, and vCPUs could still be running with writable mappings cached
in their TLB.
Fix this by only skipping setting the SPTE if the SPTE is already
write-protected *and* MMU-writable is already clear. Technically,
checking only MMU-writable would suffice; a SPTE cannot be writable
without MMU-writable being set. But check both to be paranoid and
because it arguably yields more readable code.
Fixes: 46044f72c382 ("kvm: x86/mmu: Support write protection for nesting in tdp MMU") Cc: stable@vger.kernel.org Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20220113233020.3986005-2-dmatlack@google.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, rcu_advance_cbs_nowake() checks that a grace period is in
progress, however, that grace period could end just after the check.
This commit rechecks that a grace period is still in progress while
holding the rcu_node structure's lock. The grace period cannot end while
the current CPU's rcu_node structure's ->lock is held, thus avoiding
false positives from the WARN_ON_ONCE().
As Daniel Vacek noted, it is not necessary for the rcu_node structure
to have a CPU that has not yet passed through its quiescent state.
Tested-by: Guillaume Morin <guillaume@morinfr.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0a6890b9b4df ("bnx2x: Utilize FW 7.13.15.0.")
added validation for fastpath HSI versions for different
client init which was not meant for SR-IOV VF clients, which
resulted in firmware asserts when running VF clients with
different fastpath HSI version.
This patch along with the new firmware support in patch #1
fixes this behavior in order to not validate fastpath HSI
version for the VFs.
This new firmware addresses few important issues and enhancements
as mentioned below -
- Support direct invalidation of FP HSI Ver per function ID, required for
invalidating FP HSI Ver prior to each VF start, as there is no VF start
- BRB hardware block parity error detection support for the driver
- Fix the FCOE underrun flow
- Fix PSOD during FCoE BFS over the NIC ports after preboot driver
- Maintains backward compatibility
This patch incorporates this new firmware 7.13.21.0 in bnx2x driver.
Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com> Signed-off-by: Alok Prasad <palok@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to flush TLBs before releasing backing store otherwise userspace
is able to encounter stale entries if a) it is not declaring access to
certain buffers and b) it races with the backing store release from a
such undeclared execution already executing on the GPU in parallel.
The approach taken is to mark any buffer objects which were ever bound
to the GPU and to trigger a serialized TLB flush when their backing
store is released.
Alternatively the flushing could be done on VMA unbind, at which point
we would be able to ascertain whether there is potential a parallel GPU
execution (which could race), but essentially it boils down to paying
the cost of TLB flushes potentially needlessly at VMA unbind time (when
the backing store is not known to be going away so not needed for
safety), versus potentially needlessly at backing store relase time
(since we at that point cannot tell whether there is anything executing
on the GPU which uses that object).
Thereforce simplicity of implementation has been chosen for now with
scope to benchmark and refine later as required.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reported-by: Sushma Venkatesh Reddy <sushma.venkatesh.reddy@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Dave Airlie <airlied@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On an imx6dl-pico-pi board with a QCA9377 SDIO chip, simply trying to
connect via ssh to another machine causes:
[ 55.824159] ath10k_sdio mmc1:0001:1: failed to transmit packet, dropping: -12
[ 55.832169] ath10k_sdio mmc1:0001:1: failed to submit frame: -12
[ 55.838529] ath10k_sdio mmc1:0001:1: failed to push frame: -12
[ 55.905863] ath10k_sdio mmc1:0001:1: failed to transmit packet, dropping: -12
[ 55.913650] ath10k_sdio mmc1:0001:1: failed to submit frame: -12
[ 55.919887] ath10k_sdio mmc1:0001:1: failed to push frame: -12
, leading to an ssh connection failure.
One user inspected the size of frames on Wireshark and reported
the followig:
"I was able to narrow the issue down to the mtu. If I set the mtu for
the wlan0 device to 1486 instead of 1500, the issue does not happen.
The size of frames that I see on Wireshark is exactly 1500 after
setting it to 1486."
Clearing the HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE avoids the problem and
the ssh command works successfully after that.
Introduce a 'credit_size_workaround' field to ath10k_hw_params for
the QCA9377 SDIO, so that the HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE
is not set in this case.
Tested with QCA9377 SDIO with firmware WLAN.TF.1.1.1-00061-QCATFSWPZ-1.
Fixes: 2f918ea98606 ("ath10k: enable alt data of TX path for sdio") Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20211124131047.713756-1-festevam@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the unlikely event that both blocks 10 and 11 are marked as bad (on a
32 bit machine), then the process of marking block 10 as bad stomps on
cached entry for block 11. There are (of course) other examples.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com> Reviewed-by: Richard Weinberger <richard@nod.at> Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
[<miquel.raynal@bootlin.com>: Fixed the title] Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> Link: https://lore.kernel.org/linux-mtd/774a92693f311e7de01e5935e720a179fb1b2468.1616635406.git.ytc-mb-yfuruyama7@kioxia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hmm_range_fault() can be used instead of get_user_pages() for devices
which allow faulting however unlike get_user_pages() it will return an
error when used on a VM_MIXEDMAP range.
To make hmm_range_fault() more closely match get_user_pages() remove
this restriction. This requires dealing with the !ARCH_HAS_PTE_SPECIAL
case in hmm_vma_handle_pte(). Rather than replicating the logic of
vm_normal_page() call it directly and do a check for the zero pfn
similar to what get_user_pages() currently does.
Also add a test to hmm selftest to verify functionality.
Link: https://lkml.kernel.org/r/20211104012001.2555676-1-apopple@nvidia.com Fixes: da4c3c735ea4 ("mm/hmm/mirror: helper to snapshot CPU page table") Signed-off-by: Alistair Popple <apopple@nvidia.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Zi Yan <ziy@nvidia.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: 115978859272 ("i825xx: Move the Intel 82586/82593/82596 based drivers") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dtx_diff suggests to use <(...) syntax to pipe two inputs into it, but
this has never worked: The /proc/self/fds/... paths passed by the shell
will fail the `[ -f "${dtx}" ] && [ -r "${dtx}" ]` check in compile_to_dts,
but even with this check removed, the function cannot work: hexdump will
eat up the DTB magic, making the subsequent dtc call fail, as a pipe
cannot be rewound.
Simply remove this broken example, as there is already an alternative one
that works fine.
Fixes: 10eadc253ddf ("dtc: create tool to diff device trees") Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Reviewed-by: Frank Rowand <frank.rowand@sony.com> Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20220113081918.10387-1-matthias.schiffer@ew.tq-group.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This property was already mentioned in the old textual bindings
amlogic,meson-vpu.txt, but got dropped during conversion.
Adding it back similar to amlogic,gx-vdec.yaml.
Fixes: 6b9ebf1e0e67 ("dt-bindings: display: amlogic, meson-vpu: convert to yaml") Signed-off-by: Alexander Stein <alexander.stein@mailbox.org> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20211219094155.177206-1-alexander.stein@mailbox.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is used in meson-gx and meson-g12. Add the property to the binding.
This fixes the dtschema warning:
hdmi-tx@c883a000: 'sound-name-prefix' does not match any of the
regexes: 'pinctrl-[0-9]+'
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org> Fixes: 376bf52deef5 ("dt-bindings: display: amlogic, meson-dw-hdmi: convert to yaml") Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20211223122434.39378-2-alexander.stein@mailbox.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang static analysis reports this issue
ocelot_flower.c:563:8: warning: 1st function call argument
is an uninitialized value
!is_zero_ether_addr(match.mask->dst)) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The variable match is used before it is set. So move the
block.
Fixes: 75944fda1dfe ("net: mscc: ocelot: offload ingress skbedit and vlan actions to VCAP IS1") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change
modules") unintetionally changed the semantics for high power modules
without the digital diagnostics monitoring. We repeatedly attempt to
read the power status from the non-existing 0xa2 address in a futile
hope this failure is temporary:
[ 8.856051] sfp sfp-eth3: module NTT 0000000000000000 rev 0000 sn 0000000000000000 dc 160408
[ 8.865843] mvpp2 f4000000.ethernet eth3: switched to inband/1000base-x link mode
[ 8.873469] sfp sfp-eth3: Failed to read EEPROM: -5
[ 8.983251] sfp sfp-eth3: Failed to read EEPROM: -5
[ 9.103250] sfp sfp-eth3: Failed to read EEPROM: -5
We previosuly assumed such modules were powered up in the correct mode,
continuing without further configuration as long as the required power
class was supported by the host.
Restore this behaviour, while preserving the intent of subsequent
patches to avoid the "Address Change Sequence not supported" warning
if we are not going to be accessing the DDM address.
Fixes: 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change modules") Reported-by: 照山周一郎 <teruyama@springboard-inc.jp> Tested-by: 照山周一郎 <teruyama@springboard-inc.jp> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang static analysis reports this problem
mtk_eth_soc.c:394:7: warning: Branch condition evaluates
to a garbage value
if (err)
^~~
err is not initialized and only conditionally set.
So intitialize err.
Fixes: 7e538372694b ("net: ethernet: mediatek: Re-add support SGMII") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq_optional()'s
call and blithely passes the negative error codes to devm_request_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL.
Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8562056f267d ("net: bcmgenet: request Wake-on-LAN interrupt") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56b765b79e9a ("htb: improved accuracy at high rates") broke
"overhead X", "linklayer atm" and "mpu X" attributes.
"overhead X" and "linklayer atm" have already been fixed. This restores
the "mpu X" handling, as might be used by DOCSIS or Ethernet shaping:
tc class add ... htb rate X overhead 4 mpu 64
The code being fixed is used by htb, tbf and act_police. Cake has its
own mpu handling. qdisc_calculate_pkt_len still uses the size table
containing values adjusted for mpu by user space.
iproute2 tc has always passed mpu into the kernel via a tc_ratespec
structure, but the kernel never directly acted on it, merely stored it
so that it could be read back by `tc class show`.
Rather, tc would generate length-to-time tables that included the mpu
(and linklayer) in their construction, and the kernel used those tables.
Since v3.7, the tables were no longer used. Along with "mpu", this also
broke "overhead" and "linklayer" which were fixed in 01cb71d2d47b
("net_sched: restore "overhead xxx" handling", v3.10) and 8a8e3d84b171
("net_sched: restore "linklayer atm" handling", v3.11).
"overhead" was fixed by simply restoring use of tc_ratespec::overhead -
this had originally been used by the kernel but was initially omitted
from the new non-table-based calculations.
"linklayer" had been handled in the table like "mpu", but the mode was
not originally passed in tc_ratespec. The new implementation was made to
handle it by getting new versions of tc to pass the mode in an extended
tc_ratespec, and for older versions of tc the table contents were analysed
at load time to deduce linklayer.
As "mpu" has always been given to the kernel in tc_ratespec,
accompanying the mpu-based table, we can restore system functionality
with no userspace change by making the kernel act on the tc_ratespec
value.
Fixes: 56b765b79e9a ("htb: improved accuracy at high rates") Signed-off-by: Kevin Bracey <kevin@bracey.fi> Cc: Eric Dumazet <edumazet@google.com> Cc: Jiri Pirko <jiri@resnulli.us> Cc: Vimalkumar <j.vimal@gmail.com> Link: https://lore.kernel.org/r/20220112170210.1014351-1-kevin@bracey.fi Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Linux bonding scenario, one packet is copied to several copies and sent
by all slave device of bond0 in mode 3(broadcast mode). The mode 3 xmit
function bond_xmit_broadcast() only ueses the last slave device's tx result
as the final result. In this case, if the last slave device is down, then
it always return NET_XMIT_DROP, even though the other slave devices xmit
success. It may cause the tx statistics error, and cause the application
(e.g. scp) consider the network is unreachable.
For example, use the following command to configure server A.
echo 3 > /sys/class/net/bond0/bonding/mode
ifconfig bond0 up
ifenslave bond0 eth0 eth1
ifconfig bond0 192.168.1.125
ifconfig eth0 up
ifconfig eth1 down
The slave device eth0 and eth1 are connected to server B(192.168.1.107).
Run the ping 192.168.1.107 -c 3 -i 0.2 command, the following information
is displayed.
PING 192.168.1.107 (192.168.1.107) 56(84) bytes of data.
64 bytes from 192.168.1.107: icmp_seq=1 ttl=64 time=0.077 ms
64 bytes from 192.168.1.107: icmp_seq=2 ttl=64 time=0.056 ms
64 bytes from 192.168.1.107: icmp_seq=3 ttl=64 time=0.051 ms
192.168.1.107 ping statistics
0 packets transmitted, 3 received
Actually, the slave device eth0 of the bond successfully sends three
ICMP packets, but the result shows that 0 packets are transmitted.
Also if we use scp command to get remote files, the command end with the
following printings.
ssh_exchange_identification: read: Connection timed out
So this patch modifies the bond_xmit_broadcast to return NET_XMIT_SUCCESS
if one slave device in the bond sends packets successfully. If all slave
devices send packets fail, the discarded packets stats is increased. The
skb is released when there is no slave device in the bond or the last slave
device is down.
Fixes: ae46f184bc1f ("bonding: propagate transmit status") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These properties aren't documented nor implemented in the driver.
Drop them.
Fixes warnings as:
$ make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/msm/gpu.yaml
...
arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml: gpu@b00000: 'qcom,gpu-quirk-fault-detect-mask', 'qcom,gpu-quirk-two-pass-use-wfi' do not match any of the regexes: 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/display/msm/gpu.yaml
...
DEVLINK_CMD_HEALTH_REPORTER_DUMP_GET command doesn't have .doit callback
and has no use in internal_flags at all. Remove this misleading assignment.
Fixes: e44ef4e4516c ("devlink: Hang reporter's dump method on a dumpit cb") Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of commit bf794bf52a80c627 ("powerpc/kprobes: Fix kallsyms
lookup across powerpc ABIv1 and ABIv2"), in ppc64 ABIv1, our perf
command eliminates the need to use the prefix "." at the symbol name.
But when the command "perf probe -a schedule" is executed on ppc64
ABIv1, it obtains two symbol address information through /proc/kallsyms,
for example:
The symbol "D schedule" is not a function symbol, and perf will print:
"p:probe/schedule _text+13958584"Failed to write event: Invalid argument
Therefore, when searching symbols from map and adding probe point for
them, a symbol type check is added. If the type of symbol is not a
function, skip it.
Fixes: bf794bf52a80c627 ("powerpc/kprobes: Fix kallsyms lookup across powerpc ABIv1 and ABIv2") Signed-off-by: Zechuan Chen <chenzechuan1@huawei.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jianlin Lv <Jianlin.Lv@arm.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: Yang Jihong <yangjihong1@huawei.com> Link: https://lore.kernel.org/r/20211228111338.218602-1-chenzechuan1@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware channel next descriptor view structure contains just
fields of 32 bits, while dma_addr_t can be of type u64 or u32
depending on CONFIG_ARCH_DMA_ADDR_T_64BIT. Force u32 to comply with
what the hardware expects.
Since tx_submit can be called from a hard IRQ, xfers_list must be
protected with a lock to avoid concurency on the list's elements.
Since at_xdmac_handle_cyclic() is called from a tasklet, spin_lock_irq
is enough to protect from a hard IRQ.
Cyclic channels must too call issue_pending in order to start a transfer.
Start the transfer in issue_pending regardless of the type of channel.
This wrongly worked before, because in the past the transfer was started
at tx_submit level when only a desc in the transfer list.
tx_submit is supposed to push the current transaction descriptor to a
pending queue, waiting for issue_pending() to be called. issue_pending()
must start the transfer, not tx_submit(), thus remove
at_xdmac_start_xfer() from at_xdmac_tx_submit(). Clients of at_xdmac that
assume that tx_submit() starts the transfer must be updated and call
dma_async_issue_pending() if they miss to call it (one example is
atmel_serial).
As the at_xdmac_start_xfer() is now called only from
at_xdmac_advance_work() when !at_xdmac_chan_is_enabled(), the
at_xdmac_chan_is_enabled() check is no longer needed in
at_xdmac_start_xfer(), thus remove it.
Using grep -C with perf script -D can give erroneous results as grep loses
lines due to non-printable characters, for example, below the 0020, 0060
and 0070 lines are missing:
0 0 0x450 [0x98]: PERF_RECORD_AUXTRACE_INFO type: 1
PMU Type 8
Time Shift 31
perf's isprint() is a custom implementation from the kernel, but the
kernel's _ctype appears to include characters from Latin-1 Supplement which
is not compatible with, for example, UTF-8. Fix by checking also isascii().
Fixes: 3052ba56bcb58904 ("tools perf: Move from sane_ctype.h obtained from git to the Linux's original") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Link: http://lore.kernel.org/lkml/20220112085057.277205-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mask the ECN bits before calling ip_route_output_ports(). The tos
variable might be passed directly from an IPv4 header, so it may have
the last ECN bit set. This interferes with the route lookup process as
ip_route_output_key_hash() interpretes this bit specially (to restrict
the route scope).
Mask the ECN bits before initialising ->flowi4_tos. The tunnel key may
have the last ECN bit set, which will interfere with the route lookup
process as ip_route_output_key_hash() interpretes this bit specially
(to restrict the route scope).
Similar to commit 94e2238969e8 ("xfrm4: strip ECN bits from tos field"),
clear the ECN bits from iph->tos when setting ->flowi4_tos.
This ensures that the last bit of ->flowi4_tos is cleared, so
ip_route_output_key_hash() isn't going to restrict the scope of the
route lookup.
Use ~INET_ECN_MASK instead of IPTOS_RT_MASK, because we have no reason
to clear the high order bits.
Found by code inspection, compile tested only.
Fixes: 4da3089f2b58 ("[IPSEC]: Use TOS when doing tunnel lookups") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When under stress, cleanup_net() can have to dismantle
netns in big numbers. ops_exit_list() currently calls
many helpers [1] that have no schedule point, and we can
end up with soft lockups, particularly on hosts
with many cpus.
Even for moderate amount of netns processed by cleanup_net()
this patch avoids latency spikes.
[1] Some of these helpers like fib_sync_up() and fib_sync_down_dev()
are very slow because net/ipv4/fib_semantics.c uses host-wide hash tables,
and ifindex is used as the only input of two hash functions.
ifindexes tend to be the same for all netns (lo.ifindex==1 per instance)
This will be fixed in a separate patch.
Fixes: 72ad937abd0a ("net: Add support for batching network namespace cleanups") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both fields can be read/written without synchronization,
add proper accessors and documentation.
Fixes: d5dd88794a13 ("inet: fix various use-after-free in defrags units") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function bacct_add_task the code reading task->exit_code was
introduced in commit f3cef7a99469 ("[PATCH] csa: basic accounting over
taskstats"), and it is not entirely clear what the taskstats interface
is trying to return as only returning the exit_code of the first task
in a process doesn't make a lot of sense.
As best as I can figure the intent is to return task->exit_code after
a task exits. The field is returned with per task fields, so the
exit_code of the entire process is not wanted. Only the value of the
first task is returned so this is not a useful way to get the per task
ptrace stop code. The ordinary case of returning this value is
returning after a task exits, which also precludes use for getting
a ptrace value.
It is common to for the first task of a process to also be the last
task of a process so this field may have done something reasonable by
accident in testing.
Make ac_exitcode a reliable per task value by always returning it for
every exited task.
Setting ac_exitcode in a sensible mannter makes it possible to continue
to provide this value going forward.
With the latest stable kernel versions the rtc on the PXA based
Zaurus does not work, when booting I see the following kernel messages:
pxa-rtc pxa-rtc: failed to find rtc clock source
pxa-rtc pxa-rtc: Unable to init SA1100 RTC sub-device
pxa-rtc: probe of pxa-rtc failed with error -2
hctosys: unable to open rtc device (rtc0)
I think this is because commit f2997775b111 ("rtc: sa1100: fix possible
race condition") moved the allocation of the rtc_device struct out of
sa1100_rtc_init and into sa1100_rtc_probe. This means that pxa_rtc_probe
also needs to do allocation for the rtc_device struct, otherwise
sa1100_rtc_init will try to dereference a null pointer. This patch adds
that allocation by copying how sa1100_rtc_probe in
drivers/rtc/rtc-sa1100.c does it; after the IRQs are set up a managed
rtc_device is allocated.
I've tested this patch with `qemu-system-arm -machine akita` and with a
real Zaurus SL-C1000 applied to 4.19, 5.4, and 5.10.
projects / thirdparty / kernel / stable.git / log
